Washing Machine User`s Manual
Contents
1. S 12 EN Washing Machine User s Manual 4 6 Special programmes For specific applications select any of the following programmes e Rinse Use this programme when you want to rinse or starch separately e Spin Drain Use this programme to apply an additional spin cycle for your laundry or to drain the water in the machine Before selecting this programme select the desired spin speed and press Start Pause button First the machine will drain the water inside of it Then it will spin the laundry with the set spin speed and drain the water coming out of them If you wish to drain only the water without spinning your laundry select the Pump Spin programme and then select the No Spin function with the help of Spin Speed Adjustment button Press Start Pause button GJ Use a lower spin speed for delicate laundries 4 7 Temperature selection Whenever a new programme is selected the maximum temperature for the selected programme appears on the temperature indicator To decrease the temperature press the Temperature Adjustment button Temperature will decrease gradually If the programme has not reached the heating step GJ you can change the temperature without switching the machine to Pause mode 4 8 Spin speed selection Whenever a new programme is selected the recommended spin speed of the selected programme is displayed on the spin speed indicator To decr2. EN Washing Machine User s Manual 24 EN Washing Machine User s Manual
3. Manufacturer shall not be held liable for damages that may arise from procedures carried out by nauthorized persons AN WARN NG Prior to installation visually check if the product has any defects on it If so do not have it installed Damaged products cause risks for your safety ake sure that the water inlet and discharge hoses as well as the power cable are not folded pinched or crushed while pushing the product into its place after installation or cleaning procedures ong pi 2 1 Appropriate installation location e Place the machine on a rigid floor Do not place it on a e rug or similar surfaces e Total weight of the washing machine and the dryer with ull loa e Dono e Dono e Place other d when they are placed on top of each other reaches to approx 180 kilograms Place the product on a solid and flat floor that has sufficient load carrying capacity l place the product on the power cable install the product at places where temperature may fall below 0 C he product at least 1 cm away from the edges of urniture 2 2 Removing packaging reinforcement Tilt the m achine backwards to remove the packaging reinforcement Remove the packaging reinforcement by pulling th 6 ribbon 2 3 Removing the transportation locks A WARN NG Do not remove the transportation locks before taking out the packaging reinforcement A WARN NG
4. Remove the transportation safety bolts before operating the washing machine Otherwise the product will be damaged 1 Loosen all the bolts with a suitable spanner until they rotate freely C 2 Remove transportation safety bolts by turning them gently 3 Attach the plastic covers supplied in the User Manual bag into the holes on the rear panel P Cay Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future Never move the product without the transportation safety bolts properly fixed in place 2 4 Connecting water supply The water supply pressure required to run the product is between 1 to 10 bars 0 1 1 MPa It is necessary to have 10 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly Attach a pressure reducing valve if water pressure is higher If you are going to use the double water inlet product as a single cold water inlet unit you must install the supplied stopper to the hot water valve before operating the product Applies for the products supplied with a blind stopper group WARNING Models with a single water inlet should not be connected to the hot water tap In such a case the laundry will get damaged or the product will switch to protection mode and will not operate AN WARNING Do not use old or used water inlet hoses
5. gt gt gt Remove the transportation safety bolts ity in the machine might be too little gt gt gt Add more laundry to the machine be overloaded with laundry gt gt gt Take out some of the laundry from the machine or distribute the load by hand to balance it homogenously in the machine e Machi Machi e Machi ine m ine m igh be leaning on a rigid item gt gt gt Make sure that the machine is not leaning on anything ne stopped shortly after the programme started igh have stopped temporarily due to low voltage gt gt gt t will resume running when the voltage restores to the normal level Programme time does not countdown On models with display Timer may stop during water intake gt gt gt Timer indicator will not countdown until the machine takes in adequate amount of water The machine will wait until there is sufficient amount of water to avoid poor washing results due to lack of water Timer indicator will resume Q ountdown after this e Timer may stop during heating step gt gt gt Timer indicator will not countdown until the machine reaches the selected temperature e Timer may stop during spinning step gt gt gt Automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the drum achine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and
6. EU This product bears a Classification symbol for waste electrical and electronic equipment WEEE This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling Do not dispose of the waste product with normal domestic and other wastes at the end of its servi ce life Take it to the collection center for the recycling of electrical and elec tronic equipment Please consult your local authorities to learn about these collection centers Compliance with RoHS Directive The product you have purchased complies with EU RoHS Directive 2011 65 EU It does not contain harmful and prohibited materials specified in the Directive 4 EN Washing Machine User s Manual 2 Installation efer to t of the product To make the product ready for use review the inform electricity ation in the user manual and make sure that the tap water supply and water drainage systems are appropriate before calling the Authorized Service Agent If they are n any necessary arrangements carried out ot call a qualified technician and plumber to have e nearest Authorised Service Agent for installation Preparation of the location and electrical tap water and i waste water installations at the place of installation is nder customer s responsibility AN WARN NG Installation and electrical connections of the product must be carried out by the Authorized Service Agent
7. Use this programme to wash baby laundry and the laundry that belongs to allergic persons Longer heating time and an additional rinsing step provide a higher level of hygiene e Delicate Use this programme to wash your delicate clothes It washes with a gentle action without any interim spin compared to the Synthetics programme e Hand Wash Use this programme to wash your woolen delicate clothes that bear not machine washable tags and for which hand wash is recommended It washes laundry with a very gentle washing action to not to damage clothes e Daily Xpress Use this programme to quickly wash your little amount of lightly soiled cotton clothes e Xpress Super Short Use this programme to wash your little amount of lightly soiled cotton clothes in a short time Dark Care Use this programme to wash your dark coloured laundry or the coloured laundry that you do not want them get faded Washing is performed with less mechanical movements at low temperature It is recommended to use liquid detergent or wool shampoo for dark coloured laundry e Mix 40 Use this programme to wash your cotton and synthetic clothes together without sorting them e Shirts Use this programme to wash the shirts made of cotton synthetic and synthetic blended fabrics together e Sports Use this programme to wash your garments that are worn for a short time such as sportswear It is suitable to wash little amount of cotton synthetic blended garments
8. and colour of the fabric e Use different detergents for coloured and white laundry e Wash your delicate clothes only with special detergents liquid detergent wool shampoo etc used solely for delicate clothes e When washing dark coloured clothes and quilts it is recommended to use liquid detergent e Wash woolens with special detergent made specifically for woolens WARNING Use only detergents manufactured specifically for washing machines A Adjusting detergent amount The amount of washing detergent to be used depends on the amount of laundry the degree of soiling and water hardness e Do not use amounts exceeding the dosage quantities recommended on the detergent package to avoid problems of excessive foam poor rinsing financial savings and finally environmental protection e Use lesser detergent for small amounts or lightly soiled clothes Using softeners Pour the softener into the softener compartment of the detergent drawer e Do not exceed the gt max lt level marking in the softener compartment e f the softener has lost its fluidity dilute it with water before putting it in the detergent drawer Using liquid detergents If the product contains a liquid detergent cup e Make sure that you have placed the liquid detergent cup in compartment nr 2 e f the liquid detergent has lost its fluidity dilute it with water before putting in the detergent cup WARNING D
9. hair removal This function helps to remove pet hair that remain on your garments more effectively When you select this function Prewash and Extra Rinse steps are added to the normal programme Thus washing is performed with more water 30 and the pet hair is removed more effectively A N Never wash your pets in the washing machine Delayed Start With the Delayed Start function the startup of the programme may be delayed up to 19 hours Delayed start time can be increased by increments of 1 hour i Open the loading door place the laundry and put detergent etc Select the washing programme temperature spin speed and if required the auxiliary functions Set the desired time by pressing the Delayed Start button Press Start Pause button The delayed start time you have set is displayed Delayed start countdown starts _ symbol next to the delayed start time moves up and down on the display Do not use liquid detergents when you set Delayed Start There is the risk of staining of the clothes Additional laundry may be loaded during the delayed start period At the end of the countdown duration of the selected programme will be displayed _ symbol will disappear and the selected programme will start Changing the Delayed Start period If you want to change the time during countdown Press Delayed Start button Time will increase by 1 hour each time you pr
10. perform the Initial Use procedure in accordance with the methods described under 5 2 Cleaning the loading door and the drum section of the user manual Use an anti limescale suitable for the washing machines Some water might have remained in the product due to the quality control processes in the production It is not G harmful for the product 3 5 Correct load capacity The maximum load capacity depends on the type of laundry the degree of soiling and the washing programme desired The machine automatically adjusts the amount of water according to the weight of the loaded laundry WARNING Follow the information in the Programme and consumption table When overloaded machine s washing performance will drop Moreover noise and vibration problems may occur Laundry type Weight g Bathrobe 1200 Napkin 100 Duvet cover 700 Bed Sheet 500 Pillowcase 200 Tablecloth 250 Towel 200 Hand towel 100 Evening gown 200 Underclothing 100 Men s overalls 600 Men s shirt 200 Men s pajamas 500 Blouses 100 7 EN Washing Machine User s Manual 3 6 Loading the laundry 1 Open the loading door 2 Place laundry items loosely into the machine 3 Push the loading door to close until you hear a locking sound Ensure that no items are caught in the door The loading door is locked while a programme is running The door can only be opened a while after the prog
11. to its surrounding environment Laundry should be rearranged and re spun Foam is overflowing from the detergent drawer e Too much detergent is used gt gt gt Mix 1 tablespoontul softener and water and pour into the main wash compartment of the detergent drawer Put detergent into the machine suitable for the programmes and maximum loads indicated in the Programme and consumption table When you use additional chemicals stain removers bleachs and etc reduce the amount of detergent Laundry remains wet at the end of the programme e Excessive foam might have occurred and automatic foam absorption system might have been activated due to too much detergent usage gt gt gt Use recommended amount of detergent e Machine does not switch to spinning step when the laundry is not evenly distributed in the drum to prevent any damage to the machine and 0 its surrounding environment Laundry should be rearranged and re spun A WARNING If you cannot eliminate the problem although you follow the instructions in this section consult your dealer or the Authorized Service Agent Never try to repair a nonfunctional product yourself 22 EN Washing Machine User s Manual PRODUCT FICHE Complying Commission Delegated Regulation EU No 1061 2010 Supplier name or trademark odel name WMB 51032 UY Rated capacity kg Energy efficiency class Annual Energy Consumption kWh Energy consum
12. WMB 51032 UY Washing Machine Users Manual Document Number 2820523773 02 01 14 20 39 1 Important instructions for safety and environment This section contains safety instructions that will help protect from risk of personal injury or property damage Failure to follow these instructions shall void any warranty 1 1 General safety e This product can be used by children at and above 8 years old and by persons whose physical sensory or mental capabilities were not fully developed or who lack expe rience and knowledge provided that they are supervised or trained on the safe usage of the product and the risks it brings out Children must not play with the product Cleaning and maintenance works should not be performed by children unless they are supervised by someone e Never place the product on a carpet covered floor Otherwise lack of airflow beneath the machine will cause electrical parts to overheat This will cause problems with your product e f the product has a failure it should not be operated unless it is repaired by the Authorized Service Agent There is the risk of electric shock e This product is designed to resume operating in the event of powering on after a power interruption If you wish to cancel the programme see Cancelling the pro gramme section e Connect the product to a grounded outlet protected by a 16 A fuse Do not neglect to have the grounding installation made by a qualifie
13. and curtains i e Quick Wash This function can be used in Cottons and Synthetics programmes It decreases the washing times and also the number of rinsing steps for lightly soiled laundry i When you select this function load your machine with half of the maximum laundry specified in the e Extra Rinse programme table This function enables the machine to make another rinsing in addition to the one already made after the main wash Thus the risk for sensitive skins babies allergic skins etc to be effected by the minimal detergent remnants on the laundry can be reduced e Anti Crease This function creases the clothes lesser when they are being washed Drum movement is reduced and spinning speed is limited to prevent creasing In addition washing is done with a higher water level e Rinse Hold f you are not going to unload your clothes immediately after the programme completes you may use rinse hold function to keep your laundry in the final rinsing water in order to prevent them from getting wrinkled when there is no water in the machine Press Start Pause button after this process if you want to drain the water without spinning your laundry Programme will resume and complete after draining the water f you want to spin the laundry held in water adjust the Spin Speed and press Start Pause button The programme resumes Water is drained laundry is spun and the programme is completed e Pet
14. ay from the reach of the children by closing the cover of the detergent container or sealing the detergent package While washing the laundry at high temperatures the loading door glass becomes hot Therefore keep especially the children away from the loading door of the machine while the washing operation is in progress 1 4 Package information e Packaging materials of the product are manufactured from recyclable materials in ac cordance with our National Environment Regulations Do not dispose of the packaging materials together with the domestic or other wastes Take them to the packaging material collection points designated by the local authorities 1 5 Disposing of the waste product e This product has been manufactured with high quality parts and materials which can be reused and are suitable for recycling Therefore do not dispose the product with normal domestic waste at the end of its service life Take it to a collection point for the recycling of electrical and electronic equipment Please consult your local authorities to learn the nearest collection point Help protect the environment and natural resour ces by recycling used products For children s safety cut the power cable and break the locking mechanism of the loading door so that it will be non functional before dis posing of the product 3 EN Washing Machine User s Manual 1 6 Compliance with WEEE Directive This product complies with EU WEEE Directive 2012 19
15. cates Recommended temperature Recommended temperature Recommended Recommended e range aet range range based on soiling level 1 range based on soiling level i ie p 40 90 C cold 40 C based on soiling level based on soiling level cold 40 C cold 30 C It may be necessary to pre aa treat the stains or perform ee ended prewash Powder and liquid f i b dat Liquid det t Heavily Soiled detergents recommended or colours can be used ai iquid detergents y pries en awia dosages recommended for suitable for colours difficult stai h dosages recommended for heavily soiled clothes It is and dark colours can itticult S a SUC heavily soiled clothes It is recommended to use powder be used at dosages as grass COIEe recommended to use powder detergents to clean clay and recommended for fruits and blood detercents to clean clay and SOl Stains and the stains that heavily soiled clothes g are sensitive to bleaches Use ergents without bleach Prefer liquid detergents produced for delicate clothes Woolen and silk clothes must be washed with special woolen detergents soil stains and the stains that a are sensitive to bleaches Prefer liquid detergents produced for delicate clothes Powder and liquid detergents Liquid detergents recommended for colours suitable for colours l can be used at dosages and dark colours can l For example stains can be used at dosages recommended for normally sed at
16. ccording to the selected spin speed 15 7 EN Washing Machine User s Manual 4 10 Auxiliary function selection Select the desired auxiliary functions before starting the programme Furthermore you may also select or cancel auxiliary functions that are suitable to the running programme without pressing the Start Pause button when the machine is operating For this the machine must be in a step before the auxiliary function you are going to select or cancel If the auxiliary function cannot be selected or canceled light of the relevant auxiliary function will blink 3 times to warn the user Some functions cannot be selected together If a second auxiliary function conflicting with the first one is selected before starting the machine the function selected first will be canceled and the second auxiliary function selection will remain active For example if you want to select Quick Wash after you have selected the Prewash Prewash will be canceled and Quick Wash will remain active i An auxiliary function that is not compatible with the programme cannot be selected See Programme and consumption table i Auxiliary Function buttons may vary according to the model of the machine i e Prewash A Prewash is only worthwhile for heavily soiled laundry Not using the Prewash will save energy water detergent and time Prewash without detergent is recommended for tulle
17. d cycle and 60 C cotton standard cycle and indicated with the lt _ symbols on the panel The auxiliary functions in the table may vary according to the model of your machine Water and power consumption may vary subject to the changes in water pressure water hardness and temperature ambient temperature type and amount of laundry selection of auxiliary functions and spin speed and changes in electric voltage You can see the washing time of the programme you have selected on the display of the machine It is normal that small differences may occur between the time shown on the display and the real washing time Selectability of auxiliary functions might be changed by the manufacturer New selectabilities might be added or existing ones might be removed The spin speed of your machine may vary among the programmes however this speed cannot exceed the max spin speed of your machine Been Indicative values for Synthetics programmes EN Remaining Moisture Remaining Moisture Content Content lt 1000 rpm gt 1000 rpm Z x Q 5 E 5 72 a gt 5 S d C U Programme Duration min You can see the washing time of the programme you have selected on the display of the machine It is normal that small differences may occur between the time shown on the display and the real washing time P Remaining moisture content values may differ a
18. d it must be replaced by the manufacturer after sales service or a similarly qualified person preferably an electrician or someone designa ted by the importer in order to avoid possible risks 2 7EN Washing Machine User s Manual e Place the product on a rigid flat and level surface e Do not place it on a long pile rug or similar surfaces e Do not place the product on a high platform or near the edge on a cascaded surface e Do not place the product on the power cable e Never use sponge or scrub materials These will damage the painted chrome plated and plastic surfaces 1 2 Intended use e This product has been designed for domestic use It is not suitable for commercial use and it must not be used out of its intended use e The product must only be used for washing and rinsing of laundry that are marked accordingly e The manufacturer waives any responsibility arisen from incorrect usage or transporta tion 1 3 Children s safety e Packaging materials are dangerous to children Keep packaging materials in a safe place away from reach of the children e Flectrical products are dangerous for the children Keep children away from the pro duct when it is in use Do not let them to tamper with the product Use child lock to prevent children from intervening with the product e Do not forget to close the loading door when leaving the room where the product is located e Store all detergents and additives in a safe place aw
19. d electrician Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations e The water supply and draining hoses must be securely fastened and remain undama ged Otherwise there is the risk of water leakage e Never open the loading door or remove the filter while there is still water in the drum Otherwise risk of flooding and injury from hot water will occur e Do not force open the locked loading door The loading door will be ready to open just a few minutes after the washing cycle comes to an end In case of forcing the loading door to open the door and the lock mechanism may get damaged e Unplug the product when not in use e Never wash the product by spreading or pouring water onto it There is the risk of electric shock e Never touch the plug with wet hands Never unplug by pulling on the cable always pull out by grabbing the plug e Use detergents softeners and supplements suitable for automatic washing machines only e Follow the instructions on the textile tags and on the detergent package e The product must be unplugged during installation maintenance cleaning and repai ring procedures e Always have the installation and repairing procedures carried out by the Authorized Service Agent Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons e f the power cable is damage
20. dosages Woolen and silk caused by body on recommended for normally Soiled clothes Use detergents mended for clothes must be collars and cuffs soiled clothes f washed with special without bleach ally soiled clothes woolen detergents Normally Soiled Powder and liquid detergents recommended for whites Soiling Level Prefer liquid Powder and liquid detergents Liquid detergents detergents produced Lightly Soiled recommended for colours itable for colours 5 Rad recommended T can be used at dosages dark colours can for oeae comes No visible stains S recommended for lightly be used at dosages a eee for lightly soiled soiled clothes Use detergents recommended for lightly lie as EEM without bleach ed clothes woolen detergents Powder and liquid detergents 10 EN Washing Machine User s Manual 4 Operating the product 4 1 Control panel O 8 7 6 1 Programme Selection knob Uppermost position On Off 5 Start Pause button 2 Display 6 Auxiliary Function buttons 3 Delayed Start button 7 Spin Speed Adjustment button 4 Programme Follow up indicator 8 Temperature Adjustment button 11 7 EN Washing Machine User s Manual 4 2 Preparing the machine Make sure that the hoses are connected tightly Plug in your machine Turn the tap on completely Place the laundry in the machine Add detergent and fabric s
21. ease the spin speed press the Spin Speed Adjustment button Spin speed decreases gradually Then depending on the model of the product Rinse Hold and No Spin options appear on the display See Auxiliary function selection section for explanations of these options you can change the speed without switching the i If the programme has not reached the spinning step machine to Pause mode 13 EN Washing Machine User s Manual 4 9 Programme and consumption table Programme Temperature Energy Consumption kWh Water Consumption I Max Speed Quick Wash Anti Crease Rinse Hold Pet hair removal sann rna y a rr pa raps g arra o GHR e a OOO OR SDE mwa oe e e a D 9 mea far fast or TTT fe aa SE e 1 R RD 59 pro e e fof eT TT fe so pares pe fst pepe ORO oe aez TSO E fs R ORO ar T we fep e pe a OOO we Jel eepe o e o EAEE 0 E afea E me ee e pee OO S OO S Z mes o fe me fojaj e teja O OOO Ea MEAE eet E e Selectable Automatically selected no canceling Energy Label programme EN 60456 Ed 3 lf maximum spin speed of the machine is lower then this value you can only select up to the maximum spin speed See the programme description for maximum load 147 EN Washing Machine User s Manual Cotton Economic 40 C and Cotton Economic 60 C are standard cycles These cycles are known as 40 C cotton standar
22. ed If you press any seconds while any programme is running The lights on the Lock switch the Programme Selection knob to On GJ when the machine is unplugged If no change is allowed the relevant light will flash for 3 times 4 13 Progress of programme Progress of a running programme can be followed from the Programme Follow up indicator At the beginning of every programme step the relevant indicator light will turn on and light of the completed step will turn off You can change the auxiliary functions speed and temperature settings without stopping the programme flow while the programme is running To do this the change you are going to make must be in a step after the running programme step If the change is not compatible relevant lights will flash for 3 times If the machine does not pass to the spinning step GJ Rinse Hold function might be active or the automatic unbalanced load detection system might be activated due to the unbalanced distribution of the laundry in the machine 4 14 Loading door lock There is a locking system on the loading door of the machine that prevents opening of the door in cases when the water level is unsuitable Loading door light will start flashing when the machine is switched to Pause mode Machine checks the level of the water inside If the level is suitable Loading Door light illuminates steadily within 1 2 minutes and the loading door can be op
23. ed settings if necessary Press Start Pause button to start the machine 17 EN Washing Machine User s Manual 4 16 Canceling the programme To cancel the programme turn the Programme Selection knob to select another programme Previous programme will be canceled End Cancel light will flash continuously to notify that the programme has been canceled Pump function is activated for 1 2 minutes regardless of the programme step and whether there is water in the machine or not After this period your machine will be ready to start with the first step of the new programme Depending on the step where the programme was GJ canceled in you may have to put detergent and softener again for the programme you have selected anew 4 17 End of programme End appears on the display at the end of the programme Wait until the loading door light illuminates steadily Press On Off button to switch off the machine Take out your laundry and close the loading door Your machine is ready for the next washing cycle 4 18 Your machine is equipped with a Standby Mode In case of not starting any programme or waiting without making any other operation when the machine is turned on by On Off button and while it is in selection step or if no other operation is performed approximately 2 minutes after the programme you selected has come to an end your machine will automatically switch to energy saving mode Bri
24. ened If the level is unsuitable Loading Door light turns off and the loading door cannot be opened If you are obliged to open the Loading Door while the Loading Door light is off you have to cancel the current programme see Canceling the programme 4 15 Changing the selections after programme has started Switching the machine to pause mode Press the Start Pause button to switch the machine to pause mode while a programme is running The light of the step which the machine is in starts flashing in the Programme Follow up indicator to show that the machine has been switched to the pause mode Also when the loading door is ready to be opened Loading Door light will also illuminate continuously in addition to the programme step light Changing the speed and temperature settings for auxiliary functions Depending on the step the programme has reached you may cancel or activate the auxiliary functions see Auxiliary function selection You may also change the speed and temperature settings see Spin speed selection and Temperature selection Adding or taking out laundry Press the Start Pause button to switch the machine to pause mode The programme follow up light of the relevant step during which the machine was switched into the pause mode will flash Wait until the Loading Door can be opened Open the Loading Door and add or take out the laundry Close the Loading Door Make changes in auxiliary functions temperature and spe
25. ess the button If you want to decrease the delayed start time press Delayed Start button repeatedly until the desired delayed start time appears on the display Canceling the Delayed Start function If you want to cancel the delayed start countdown and start the programme immediately Set the Delayed Start period to zero or turn the Programme Selection knob to any programme Thus Delayed Start function will be canceled The End Cancel light flashes continuously Then select the programme you want to run again Press Start Pause button to start the programme 16 EN Washing Machine User s Manual 4 11 Starting the programme Press Start Pause button to start the programme Programme follow up light showing the startup of the programme will turn on If no programme is started or no key is pressed within GJ 1 minute during programme selection process the machine will switch to Pause mode and the illumination level of the temperature speed and loading door indicator lights will decrease Other indicator lights and indicators will turn off Once the Programme Selection knob is rotated or any button is pressed indicator lights and indicators will turn on again 4 12 Child Lock Use Child Lock function to prevent children from tampering with the machine Thus you can avoid any changes in a running programme auxiliary functions Even if another programme is selected with the P
26. ghtness of indicator lights will decrease Also if your product is equipped with a display showing the programme duration this display will completely turn off In case of rotating the Programme Selection knob or pressing any button lights and display will restore to their previous condition Your selections made while exiting the energy saving mode may change Check the appropriateness of your selections before starting the programme Readjust if necessary This is not a fault 5 Maintenance and cleaning ervice life of the product extends and frequently face problems decrease if cleaned at regular intervals 5 1 Cleaning the detergent drawer Clean the detergent drawer at regular intervals every 4 5 washing cycles as shown below in order to prevent accumulation of powder detergent in time 1 Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine If more than normal amount of water and softener mixture starts to gather in the softener compartment the siphon must be cleaned 2 Wash the detergent drawer and the siphon with plenty of lukewarm water in a washbasin Wear protective gloves or use an appropriate brush to avoid touching of the residues in the drawer with your skin when cleaning 3 Insert the drawer back into its place after cleaning and make sure that it is seated well If your detergent drawer is the one indicated in the followi
27. h your synthetic clothes shirts blouses synthetic cotton blends etc It washes with a gentle action and has a shorter washing cycle compared to the Cottons programme For curtains and tulle use the Synthetic 40 C programme with prewash and anti creasing functions selected As their meshed texture causes excessive foaming wash the veils tulle by putting little amount of detergent into the main wash compartment Do not put detergent in the prewash compartment e Woollen Use this programme to wash your woolen clothes Select the appropriate temperature complying with the tags of your Clothes Use appropriate detergents for woolens 4 5 Additional programmes For special cases additional programmes are available in the machine Additional programmes may differ according to the model of the machine e Cottone Eco You may wash your normally soiled durable cotton and inen laundry in this programme with the highest energy and water saving compared to all other wash programmes suitable for cottons Actual water temperature may differ from the declared cycle temperature Programme duration ay automatically be shortened during later stages of the programme if you wash less amount e g capacity or less of laundry In this case energy and water consumption ill be further decreased giving you the opportunity for a ore economical wash This feature is available for certain models having remaining time display e BabyProtect
28. hours before washing This will reduce pilling e Laundry that are subjected to materials such as flour lime dust milk powder etc intensely must be shaken off before placing into the machine Such dusts and powders on the laundry may build up on the inner parts of the machine in time and can cause damage 3 3 Things to be done for energy saving Following information will help you use the product in an ecological and energy efficient manner e Operate the product in the highest capacity allowed by the programme you have selected but do not overload see Programme and consumption table e Always follow the instructions on the detergent packaging e Wash slightly soiled laundry at low temperatures e Use faster programmes for small quantities of lightly soiled laundry e Do not use prewash and high temperatures for laundry that is not heavily soiled or stained e f you plan to dry your laundry in a dryer select the highest spin speed recommended during washing process e Do not use detergent in excess of the amount recommended on the detergent package 3 4 Initial use Before starting to use the product make sure that all preparations are made in accordance with the instructions in sections Important safety instructions and Installation To prepare the product for washing laundry perform first operation in Drum Cleaning programme If your product is not equipped with Drum Cleaning programme
29. impeller during discharge of washing water Thus the water ill be discharged without any problem and the service life of the pump will extend f the machine fails to drain water the pump filter is clogged Filter must be cleaned whenever it is clogged or in every 3 months Water must be drained off first to clean the pump filter n addition prior to transporting the machine e g when moving to another house and in case of freezing of the water water may have to be drained completely A n order to clean the dirty filter and discharge the water 1 Unplug the machine to cut off the supply power WARNING Foreign substances left in the pump filter may damage your machine or may cause noise problem WARNING Temperature of the water inside the machine may rise up to 90 C To avoid burning risk filter must be Cleaned after the water in the machine cools down 2 Open the filter cap If the filter cap is composed of two pieces press the tab on the filter cap downwards and pull the piece out towards yourself LL If the filter cap is one piece pull the cap from both sides at the top to open 19 EN Washing Machine User s Manual downwards with a thin plastic tipped tool through the gap above the filter cover Do not use metal tipped tools to remove the cover i You can remove the filter cover by slightly pushing 3 Some of our products have emergency drain
30. ing hose and some does not have Follow the steps below to discharge the water Discharging the water when the product has an emergency draining hose a Pull the emergency draining hose out from its seat b Place a large container at the end of the hose Drain the water into the container by pulling out the plug at the end of the hose When the container is full block the inlet of the hose by replacing the plug After the container is emptied repeat the above procedure to drain the water in the machine completely c When draining of water is finished close the end by the plug again and fix the hose in its place d Turn the pump filter to take it out Discharging the water when the product does not have an emergency draining hose Q Un A a Place a large container in front of the filter to catch water from the filter b Loosen pump filter anticlockwise until water starts to flow Fill the flowing water into the container you have placed in front of the filter Always keep a piece of cloth handy to absorb any spilled water c When the water inside the machine is finished take out the filter completely by turning it 4 Clean any residues inside the filter as well as fibers if any around the pump impeller region Install the filter If the filter cap is composed of two pieces close the filter cap by pressing on the tab If it is one piece seat the tabs in the lower part into their places first and then pre
31. ld be attached to a height of at least 40 cm and 100 cm at most e Incase the hose is elevated after laying it on the floor level or close to the ground less than 40 cm above the ground water discharge becomes more difficult and the laundry may come out excessively wet Therefore follow the heights described in the figure e To prevent flowing of dirty water back into the machine and to allow for easy discharge do not immerse the hose end into the dirty water or do not drive it in the drain more than 15 cm If it is too long cut it short e The end of the hose should not be bent it should not be stepped on and the hose must not be pinched between the drain and the machine e lf the length of the hose is too short use it by adding an original extension hose Length of the hose may not be longer than 3 2 m To avoid water leak failures the connection between the extension hose and the drain hose of the product must be fitted well with an appropriate clamp as not to come off and leak 2 6 Adjusting the feet more silently and vibration free it must stand level and balanced on its feet Balance the machine by adjusting the feet Otherwise the product may move from its place and cause crushing and vibration problems T WARNING In order to ensure that the product operates 1 Loosen the lock nuts on the feet by hand 2 Adjust the feet until the product stands level and balanced 3 Tighten all
32. lock nuts again by hand WARNING Do not use any tools to loosen the lock nuts Otherwise they will get damaged 2 7 Electrical connection Connect the product to a grounded outlet protected by a 16 A fuse Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with the local regulations e Connection must comply with national regulations e Power cable plug must be within easy reach after installation e f the current value of the fuse or breaker in the house is less than 16 Amps have a qualified electrician install a 16 Amp fuse e The voltage specified in the Technical specifications section must be equal to your mains voltage e Do not make connections via extension cables or multi plugs WARNING Damaged power cables must be replaced by the Authorized Service Agents Transportation of the product 1 Unplug the product before transporting it 2 Remove water drain and water supply connections 3 Drain all water that has remained in the product SEE 5 5 4 Install transportation safety bolts in the reverse order of removal procedure SEE 2 3 Never move the product without the transportation safety bolts properly fixed in place g WARNING Packaging materials are dangerous to children Keep packaging materials in a safe place away from reach of the children 6 EN Washing Machine Use
33. ng figure Lift the rear part of the siphon to remove it as illustrated After performing the above mentioned cleaning procedures replace the siphon back to its seating and push its front section downwards to make sure that the locking tab engages 18 EN Washing Machine User s Manual 5 2 Cleaning the loading door and the drum Residues of softener detergent and dirt may accumulate in your machine in time and may cause unpleasant odours and washing complaints To avoid this use the Drum Cleaning programme If your machine is not featured with Drum Cleaning programme use Cottons 90 programme and select Additional Water or Extra Rinse auxiliary functions as well Run the programme without any laundry in the machine Before starting the programme put max 100 g of powder anti limescale into the main wash detergent compartment compartment nr 2 If the anti limescale is in tablet form put only one tablet into compartment nr 2 Dry the inside of the bellow with a clean piece of cloth after the programme has come to an end i Repeat Drum Cleaning process in every 2 months i Use an anti limescale suitable for the washing machines After every washing make sure that no foreign substance is left in the drum If the holes on the bellow shown in the figure is blocked open the holes using a toothpick Foreign metal substances will cause rust stains in the drum Clean the
34. o not use soap powder If the product does not contain a liquid detergent cup e Do not use liquid detergent for the prewash in a programme with prewash e Liquid detergent stains your clothes when used with Delayed Start function If you are going to use the Delayed Start function do not use liquid detergent Using gel and tablet detergent Apply the following instructions when using tablet gel and similar detergents e f the gel detergent thickness is fluidal and your machine oes not contain a special liquid detergent cup put the el detergent into the main wash detergent compartment uring first water intake If your machine contains a liquid etergent cup fill the detergent into this cup before tarting the programme Qaaaqa nD 8 EN Washing Machine User s Manual e If the gel detergent thickness is not fluidal or in the shape of capsule liquid tablet put it directly into the drum before washing e Put tablet detergents into the main wash compartment compartment nr 2 or directly into the drum before washing Tablet detergents may leave residues in the detergent GJ compartment If you encounter such a case place the tablet detergent between the laundry close to the lower part of the drum in future washings Use the tablet or gel detergent without selecting the prewash function Using starch e Add liquid starch powder starch or the fabric dye into the
35. oftener 4 3 Programme selection 1 Select the programme suitable for the type quantity and soiling degree of the laundry in accordance with the Programme and consumption table and the temperature table below 90 C Heavily soiled white cottons and linens coffee table covers tableclothes towels bed sheets etc Normally soiled coloured fade proof linens cottons or 60 C synthetic clothes shirt nightgown pajamas etc and lightly soiled white linens underwear etc aa Blended laundry including delicate textile veil curtains Cold etc synthetics and woolens 2 Select the desired programme with the Programme Selection button Programmes are limited with the highest spin speed appropriate for that particular type of fabric When selecting a programme always consider the type of fabric colour degree of soiling and permissible water i temperature Always select the lowest required temperature Higher temperature means higher power consumption GJ For further programme details see Programme and consumption table 4 4 Main programmes Depending on the type of fabric use the following main programmes e Cottons Use this programme for your cotton laundry such as bed sheets duvet and pillowcase sets towels bathrobes underwear etc Your laundry will be washed with vigorous washing action for a longer washing cycle e Synthetics Use this programme to was
36. on the new product It may cause stains on your laundry 1 Connect the special hoses supplied with the product to the water inlets on the product Red hose left max 90 C is for hot water inlet blue hose right max 25 C is for cold water inlet gt B WARNING Ensure that the cold and hot water connections are made correctly when installing the product Otherwise your laundry will come out hot at the end of the washing process and wear out 2 Tighten all hose nuts by hand Never use a tool when tightening the nuts 5 EN Washing Machine User s Manual 3 Open the taps completely after making the hose connection to check for water leaks at the connection points If any leaks occur turn off the tap and remove the nut Retighten the nut carefully after checking the seal To prevent water leakages and damages caused by them keep the taps closed when the machine is not in use 2 5 Connecting to the drain e The end of the drain hose must be directly connected to the wastewater drain or to the washbasin WARNING Your house will be flooded if the hose comes out of its housing during water discharge Moreover there is risk of scalding due to high washing temperatures To prevent such situations and to ensure smooth water intake and discharge of the machine fix the end of the discharge hose tightly so that it cannot come out e The hose shou
37. ption of the standard 60 C cotton programme at full load kWh Energy consumption of the standard 60 C cotton programme at partial load kWh Energy consumption of the standard 40 C cotton programme at partial load kWh Power consumption in off mode W Power consumption in left on mode W Annual Water Consumption 9 Spin drying efficiency class a ae Maximum spin aul rpm 1000 Penance gg N A Duration of the left on mode min Airborne acoustical noise emissions washing spinning dB 59 77 Scale from A Highest Efficiency to D Lowest Efficiency Energy Consumption based on 220 standard washing cycles for cotton programmes at 60 C and 40 C at full and partial load and the consumption of the low power modes Actual energy consumption will depend on how the appliance is used Water consumption based on 220 standard washing cycles for cotton programmes at 60 C and 40 C at full and partial load Actual water consumption will depend on how the appliance is used Scale from A Highest Efficiency to G Lowest Efficiency Standard 60 C cotton programme and the standard 40 C cotton programme are the standard washing programmes to which the information in the label and the fiche relates and these programmes are suitable to clean normally soiled cotton laundry and that they are the most efficient programmes in terms of combined energy and water consumption 23
38. r s Manual 3__Preparation 3 1 Sorting the laundry e Sort laundry according to type of fabric colour and degree of soiling and allowable water temperature e Always obey the instructions given on the garment tags 3 2 Preparing laundry for washing e Laundry items with metal attachments such as underwired bras belt buckles or metal buttons will damage the machine Remove the metal pieces or wash the clothes by putting them in a laundry bag or pillow case e Take out all substances in the pockets such as coins pens and paper clips and turn pockets inside out and brush Such objects may damage the product or cause noise problem e Put small size clothes such as infant s socks and nylon stockings in a laundry bag or pillow case e Place curtains in without compressing them Remove curtain attachment items e Fasten zippers sew loose buttons and mend rips and tears e Wash machine washable or hand washable labeled products only with an appropriate programme e Do not wash colours and whites together New dark coloured cottons release a lot of dye Wash them separately e Tough stains must be treated properly before washing If unsure check with a dry cleaner e Use only dyes colour changers and limescale removers suitable for machine wash Always follow the instructions on the package e Wash trousers and delicate laundry turned inside out e Keep laundry items made of Angora wool in the freezer for a few
39. ramme comes to an end WARNING In case of misplacing the laundry noise and vibration problems may occur in the machine A 3 7 Using detergent and softener or limescale remover read the manufacturer s instructions on the package carefully and follow the suggested dosage values Use measuring cup if available i When using detergent softener starch fabric dye bleach Detergent Drawer The detergent drawer is composed of three compartments 1 for prewash 2 for main wash 3 for softener in addition compartment here is siphon piece in the softener an WT Detergent softener and other cleaning agents e Add detergent and softener before starting the washing programme e Never leave the detergent drawer open while the washing programme is running e When using a programme without prewash do not put any detergent into the prewash compartment Compartment nr 1 e n a programme with prewash do not put liquid detergent into the prewash compartment compartment nr 1 e Do not select a programme with prewash if you are using a detergent bag or dispensing ball Place the detergent bag or the dispensing ball directly among the laundry in the machine e If you are using liquid detergent do not forget to place the liquid detergent cup into the main wash compartment Compartment nr 2 Choosing the detergent type The type of detergent to be used depends on the type
40. rogramme Selection knob while the Child Lock is 3 seconds The lights on the 1 and 2 Auxiliary Function buttons will flash and C03 C02 C01 will appear on the display respectively while you keep the buttons pressed lights on the 1st and 2nd auxiliary function buttons that are used to deactivate the Child Lock will blink 3 times To deactivate the Child Lock you keep the buttons pressed for 3 seconds Then COFF will appear on the display indicating that the Child Lock is deactivated i If the Programme Selection knob is turned when the The Child Lock does not allow any change in the programmes and the selected temperature speed and active previously selected programme will continue To activate the Child Lock Press and hold 1 and 2 Auxiliary Function buttons for for 3 seconds Then Con will appear on the display button or turn the Programme Selection knob when the Child Lock is active same phrase will appear on the display The Press and hold 1 and 2 auxiliary function buttons for 3 1 and 2 Auxiliary Function buttons will flash and C03 C02 C01 will appear on the display respectively while i In addition to the method above to deactivate the Child Off position when no programme is running and select another programme Child Lock is not deactivated after power failures or Child Lock is active Con appears on the display G running indicating that the Child Lock is activat
41. softener compartment e Do not use softener and starch together in a washing cycle e Wipe the inside of the machine with a damp and clean cloth after using starch Using bleaches e Select a programme with prewash and add the bleaching agent at the beginning of the prewash Do not put detergent in the prewash compartment As an alternative application select a programme with extra rinse and add the bleaching agent while the machine is taking water from the detergent compartment during first rinsing step e Do not use bleaching agent and detergent by mixing them e Use just a little amount approx 50 ml of bleaching agent and rinse the clothes very well as it causes skin irritation Do not pour the bleaching agent onto the clothes and do not use it for coloured clothes e When using oxygen based bleaches select a programme that washes at a lower temperature e Oxygen based bleaches can be used together with detergents however if its thickness is not the same with the detergent put the detergent first into the compartment nr 2 in the detergent drawer and wait until the detergent flows while the machine is taking in water Add the bleaching agent from the same compartment while the machine is still taking in water Using limescale remover e When required use limescale removers manufactured specifically for washing machines only 9 EN Washing Machine User s Manual 3 8 Tips for efficient washing Clothes Deli
42. ss the upper part to close oo 20 EN Washing Machine User s Manual 6 Technical specifications a a ee e Available GJ Technical specifications may be changed without prior notice to improve the quality of the product GJ Figures in this manual are schematic and may not match the product exactly Values stated on the product labels or in the documentation accompanying it are obtained in laboratory conditions in accordance with the relevant standards Depending on operational and environmental conditions of the product these values may vary 21 EN Washing Machine User s Manual 7_Troubleshooting Programme cannot be started or selected e Washing machine has switched to self protection mode due to a supply problem line voltage water pressure etc gt gt gt Press and hold Start Pause button for 3 seconds to reset the machine to factory settings See Cancelling the programme Water in the machine e Some water ight have remained in the product due to the quality control processes in the production gt gt gt This is not a failure water is not harmful to the machine Machine vibrates or makes noise ach achine migh A hard substance might have entered into the pump filter gt gt gt Clean the pump filter Iransportati Laundry qui ine m ion anti igh be standing unbalanced gt gt gt Adjust the feet to level the machine safety bolts are not removed
43. stains on the drum surface by using Cleaning agents for stainless steel Never use steel wool or wire wool i WARNING Never use sponge or scrub materials These will damage the painted and plastic surfaces A 5 3 Cleaning the body and control panel Wipe the body of the machine with soapy water or non corrosive mild gel detergents as necessary and dry with a soft cloth Use only a soft and damp cloth to clean the control panel 5 4 Cleaning the water intake filters There is a filter at the end of each water intake valve at the rear of the machine and also at the end of each water intake hose where they are connected to the tap These filters prevent foreign substances and dirt in the water to enter the washing machine Filters should be cleaned as they do get dirty E 1 Close the taps 2 Remove the nuts of the water intake hoses to access the filters on the water intake valves Clean them with an appropriate brush If the filters are too dirty take them out by means of pliers and clean them 3 Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly under running water 4 Replace the gaskets and filters carefully in their places and tighten the hose nuts by hand 5 5 Draining remaining water and cleaning the pump filter The filter system in your machine prevents solid items such as buttons coins and fabric fibers clogging the pump
Download Pdf Manuals
Related Search