PEB-3730/3732 Series User`s Manual
Contents
1. 1 3 System Architecture The system architecture of PEB 3730 3732 includes two main Intel EID chips Intel 855GME 852GM chipset supports Intel low power Pentium M or Celeron M processor DDR SDRAM Intel extreme graphics 2 and its ICH4 supports PCI bus interface APM ACPI compliant power management USB port SMBus communication and Ultra DMA 33 66 100 IDE Master and it also provides a Fast Ethernet controller The Winbond I O Controller is responsible for PS 2 Keyboard Mouse UARTs FDC Hardware Monitor Parallel Watch Dog Timer and Infrared interface The special pin configuration of the CPU socket adopts the uFC PGA2 478 pins in total This new generation Pentium M or Celeron M provides better performance to many applications As for PEB 3732 the Ultra Low Voltage Celeron M is in uFC BGA 2 is populated on board at 600Mhz with FSB 400Mhz PEB 3730 3732 Series User s Manual 1 9 System Overview The on board PCI connector can supports additional embATX PCI riser card for further PCI extension up to 3 PCI devices Pentium M IMVP IV VR Processor DDR DIMM DDR_series DDR Termination Resistors Giele Resistors amp Cap LVDS ue am Connectors IEEE 1394 82562 82540 LAN 82551 82540 Gm LANZ 200 266MHz DDR AC97 CODEC ver 2 2 1x IDE Pin Header amp 1x Compact Flash socket LPC I O Controller W83627HF LPC I O2. CPU Feature Virus Warning CPU L1 Cache CPU L2 Cache Quick Power On Self Test First Boot Device Second Boot Device Third Boot Device Boot Other Device Swap Floppy Seek Boot Up Floopy Seek Boot up NumLock Status Gate A20 Option Security Option APIC Mode Typematic Rate Setting X Typematic Rate Chars sec X Typematic delay Msec MPS Version Control For OS OS Select For DRAM gt 64MB Report No FDD For WIN 95 Small Logo EPA Show Press Enter Disabled Enabled Enabled Enabled Floppy HDD 0 LS120 Enabled Disabled Enabled On Fast Disabled 6 250 Setup Enabled 1 4 Non OS2 No Disabled Item Help Menu Level gt N gt lt Move F5 Previous Values Enter Select PU PD Value F6 Fail Safe Defaults F10 Save ESC Exit F7 Optimized Defaults F1 General Help PEB 3730 3732 Series User s Manual 4 6 BIOS Setup Information Virus Warning It allows you to choose the VIRUS warning feature for IDE Hard Disk boot sector protection If this function is enabled and someone attempt to write data into this area BIOS will show a warning message on screen and alarm beep Enabled Activates automatically when the system boots up causing a warning message to appear when anything attempts to access the boot sector or hard disk partition table Disabled No warning message will appear when anything attempts to access
3. PEB 3730 series System Block Diagram PEB 3730 3732 Series User s Manual 1 10 System Overview Celeron M 600 Processor Li CLOCK DOR DUM DDR Termination we Le H Been VE ll Resistors amp Cap es ei Gerbe AC97 CODEC E Tine In ver 2 2 IEEE 1304 NE 2 v2 3 1x IDE Pin Header amp oo mm CZ A USB Ports LS Pin header 4 WATCH DOG TIMER Header 2X5_2mm COM1 COM4 PEB 3732 series System Block Diagram PEB 3730 3732 Series User s Manual 1 11 Hardware Configuration Chapter 2 Hardware Configuration This chapter gives the definitions and shows the positions of jumpers headers and connector All of the configuration jumpers on PEB 3730 3732 series are in proper position The default jumper settings shipped from factory are marked with an astral 2 1 Jumper Setting Jumpers provide a convenient and reversible way of reconfiguring the circuitry on a printed circuit board When reconfiguring the system you may need to change jumper settings on the system board In the following sections Short means covering a jumper cap over jumper pins Open or NC Not Connected means removing a jumper cap from jumper pins Refer to Figure 2 1 for the Jumper locations LETI Jm e EE 14 J14 a LKH ererelelelerelerererelel il seisleleleie slelslelelelel BSS EE EEN EE e EE SSO geass SH 83388 SH e EH ES SS SH IPS 327 JP 135 Bl oo OOOOH 00000 200 9000000 doo Ooo 07 Do 88 0000 BSGG0 GG60
4. Power requirements TBD Operating temperature 0 to 55 C Relative Humidity 5 to 95 non condensing PEB 3730 3732 Series User s Manual 1 5 System Overview PEB 3732VLA Chipset Intel 852GM Intel GMCH and Intel ICH4 CPU Intel ULV Celeron M FSB speed 400MHz 2x32KB L1 cache 512KB L2 cache Celeron M also support OK L2 cache model by specific project based System memory One DIMM sockets Supports 200 266MHz DDR SDRAM up to 1GB Available bandwidth up to 2 1GB s DDR266 64 128 256 512 Mb SDRAM technologies 64bit non parity 2 5V DDR SDRAM support Registered DIMM not supported Support ECC functionality SSD One type I or type II Compact Flash socket Display controller Intel GMCH integrated graphics controller 852GM Integrated Intel Extreme graphics 2 Intel DVMT shared display memory up to 64MB DDR Memory Analog Display Support up to 2048 x 1536 60Hz refresh Multiplexed Digital Display Channels supports flat panels up to 2048x1536 O 60Hz or CRT HDTV at 1920 x 1080 x 18 amp 24bpp 85Hz AGP 4X 1 5V Intel Direct AGP Software DVD at 30 fps full screen Motion Video Acceleration Dual channel LVDS interface for LVDS Panel Display Support TMDS DVI port through daughter board Analogue and digital output through one DVI I connector on daughter board Panel Signal voltage must be 3 3V or 5V Inverter voltage 12V Dual LVDS ports poss
5. The choice Enabled Disabled Typematic Rate Chars sec The rate at which character repeats when you hold down a key The choice 6 8 10 12 15 20 24 30 Typematic delay Msec The delay before key strokes begin to repeat The choice 250 500 750 1000 Security Option Select whether the password is required every time the system boots or only when you enter setup System The system will not boot and access to Setup will be denied if the correct password is not entered at the prompt Setup The system will boot but access to Setup will be denied if the correct password is not entered at the prompt PEB 3730 3732 Series User s Manual 4 8 BIOS Setup Information APIC Mode The choice Enabled Disabled MPS Version Control For OS The choice 1 1 1 4 OS Select For DRAM gt 64MB Select OS 2 only if you are running SO 2 operating system with greater than 64MB of RAM on the system The choice Non OS2 OS2 Report No FDD for WIN 95 The choice No Yes Small Logo EPA Show The choice Enabled Disabled PEB 3730 3732 Series User s Manual 4 9 BIOS Setup Information 4 6 Advanced Chipset Features This section allows you to configure the system based on the specific features of the Intel 82852GME Chipset This Chipset manages bus speeds and access to system memory resources such as DRAM DDR SDRAM and the external cache It also coordinates communications between the conventional ISA
6. J13 IR Connector Signal Description 5V NC Receiving Input GND Transmitter Output NC J14 LVDS Interface Connector PIN No Signal Description PIN No Signal Description LVDS VDD LVDS VDD 4 Channel ADatal 3 Channel AData0 6 Channel ADatal JL 5 Channel ADatal 8 Channel AData2 7 Channel AData2 10 Channel A Data3 Lg Channel AData3 12 Channel A Clock f 11 ChamnelAClock 14 PanelDDCClock 13 Panel DDC Data IET B5 GND 18 O17 RE WEE 22 21 O24 28 25 2 4 10 12 14 16 GND GND 18 20 22 24 26 28 26 Channel B Clock 28 Panel DDC Clock 27 Panel DDC Data 30 GND _ GND 1 3 5 7 11 13 15 17 19 21 23 25 27 29 J15 CPU FAN Connector Function PEB 3730 3732 Series User s Manual 2 8 Hardware Configuration 16 MIC Line IN Line OUT Interface Connector PIN No Signal Description PIN No Signal Description 1 MIC 2 GND 5 LineINRight 6 GND _ y 7 LineOUTIefe Is GND 9 ine0UTRigt______ __ ______ J18 BUZZER Connector BUZZER BUZZER Signal Description MDI Signal Description MDI LANZ BI_DA LANZ BI_DA LAN2 BI_DB 4 LAN2 BI_DB LAND DC 6 LAN2BIDCH LAN2BI_DD 8 LAN2BLDD 13 Active LED 13 LANZ GND Link LED LAN2 GND 120 Thermal Sense Interface Connector Optional Signal Thermal Sens
7. PIN No Signal Description 1 GND GND Drive Density Select bit 0 oe NG e 6 Drive Density Select bit1 A INDEX 10 MotorAOn 12 DriveSeletB__ G 14 DriveSelectA G 16 MotorBOn_ ND ASADO 9 GND La str OE 21 GND Writedata GND 24 Writeemabble 26 ak S D 28 Writeprotected D 0 RDATA O o 31 GND f 32 Head Select 34 Diskette Change e 2 4 10 12 14 16 18 20 22 24 26 28 30 32 34 PEB 3730 3732 Series User s Manual 2 6 Hardware Configuration 6 Power ON OFF IDE1 Campact Flash Active LED System Reset Header Status ON Power ON OFF OFF Normal LED Power LED Power ON Reset OFF Normal 8 USB Port1 USB Port Interface Connector PIN No Signal Description PIN No Signal Description 1 USB1 Power 2 GND 5 USBiData Le USB2Datat 7 USBIGND Lg USB2Data 9 0ND 10 UsSB2Power O 9 USB Port3 USB Port4 Interface Connector PIN No Signal Description PIN No Signal Description 1 USB3 Power 2 GND 3 USB3 Data 4 USB4 GND 5 USB3 Datar Le USB4Datar 7 USB3GND_ 8 USBiData 2 GND 910 USB4Power ______ Signal Description SMBUS Clock GND SMBUS Data 5V Signal Description CD IN Left CD IN GND CD IN GND CD IN Right PEB 3730 3732 Series User s Manual 2 7 Hardware Configuration J12 System FAN Connector Function
8. PEB 3730 3732 Series User s Manual 2 12 Hardware Configuration 135 VGA Connector PIN No Signal Description PEB 3730 3732 Series User s Manual 2 13 System Installation Chapter 3 System Installation This chapter provides the instructions to set up PEB 3730 3732 series The additional information enclosed to help you set up onboard PCI device and handle Watch Dog Timer WDT operation in software programming 3 1 INF Chipset Component Driver Intel 855GM 852GME chipset is a new chipset that a few old operating systems might not be able to recognize To overcome this compatibility issue for Windows Operating Systems such as Windows 95 98 98SE 2000 please install INF Chipset Component driver before any of other Drivers are installed You can find very easily the INF chipset component driver in Chipsetl Intell INF directory of PEB 3730 3732 series CD title Please execute infinst_autol exe to start installation 3 2 Intel 855GM 852GME Graphics Controller Intel 855GM 852GME chipset is the result of new design approach to optimize the shared memory architecture while maintaining the cost benefits of integration through Direct AGP and Dynamic Video Memory Technology With no additional video adaptor this onboard video will be the system display output However system will automatically switch to off board video adaptor if there is any In this case onboard 855GM 852GME graphic features will be d
9. PEB 3730 Sereis User s Manual Appendix B Interrupt Request Lines IRQ Peripheral devices can use interrupt request lines to notify CPU for the service required The following table shows the IRQ used by the devices on board IRO Current Use Default Use IRQ 0 SMARTDRV System Timer IRQ1 SMARTDRV Keyboard Event IRQ 2 Unassigned Usable IRQ IRQ 3 System ROM COM2 IRQ 4 System ROM COM1 IRQ 5 Unassigned Usable IRQ IRQ 6 System ROM Diskette Event IRQ 7 Unassigned Usable IRQ IRQ 8 System ROM Real time Clock IRQ 9 Unassigned Usable IRQ IRQ 10 Unassigned Usable IRQ IRQ 11 Unassigned Usable IRQ IRQ 12 System ROM IBM Mouse Event IRQ 13 System ROM Coprocessor Error IRQ 14 System ROM Hard Disk Event IRQ 15 Unassigned Usable IRQ PEB 3730 Series User s Manual
10. is enabled this item could allow users to configure the date parameter of the timing dateline on which to power on the system The choice 0 31 Time hh mm ss Alarm When Resume by Alarm is enabled this item could allow users to configure the time parameter of the timing dateline on which to power on the system The choice hh 0 23 mm 0 59 ss 0 59 Primary Secondary IDE 0 1 This item is to configure IDE devices being monitored by system so as to keep system out of suspend mode if the associated device is busy The choice Enabled Disabled FDD COM LPT Port This item is to configure floppy device COM ports and parallel port being monitored by system so as to keep system out of suspend mode if the associated device is busy The choice Enabled Disabled PCI PIRQ A D This option can be used to detect PCI device activities If they are activities the system will go into sleep mode The choice Enabled Disabled PEB 3730 3732 Series User s Manual 4 22 BIOS Setup Information 4 9 PnP PCI Configurations This section describes configuring the PCI bus system PCI or Personal Computer Interconnect is a system which allows I O devices to operate at speeds nearing the speed the CPU itself uses when communicating with its own special components This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default sett
11. the boot sector or hard disk partition table CPU L1 Cache CPU L2 Cache These two categories speed up memory access However it depends on CPU chipset design Enabled Enable cache Disabled Disable cache Quick Power On Self Test Allows the system to skip certain tests while booting This will decrease the time needed to boot the system Enabled Enable quick POST Disabled Normal POST First Second Third Boot Device Select your Boot Device Priority The choice Floppy LS120 HDD 0 SCSI CDROM HDD 1 HDD 2 HDD3 ZIP100 USB FDD USB ZIP USB CDROM USB HDD and Disabled Boot Other Device Select Your Boot Device Priority The choice Enabled Disabled Swap Floppy Drive If the system has two floppy drives choose enable to assign physical driver B to logical drive A and Vice Versa The choice Enabled Disabled PEB 3730 3732 Series User s Manual 4 7 BIOS Setup Information Boot Up Floppy Seek Enabled tests floppy drives to determine whether they have 40 or 80 tracks The choice Enabled Disabled Boot Up NumLock Status Select power on state for NumLock The choice Off On Gate A20 Option Fast lets chipsets control Gate A20 and Normal a pin in the keyboard controller controls Gate A20 Default is Fast The choice Normal Fast Typematic Rate Setting Keystrokes repeat at a rate determined by the keyboard controller When enabled the typematic rate and typematic delay can be select
12. EN 61000 3 3 1995 The following manufacturer is responsible for this declaration Portwell Inc Company Name 3F No 88 Sec 1 Nei Hu Rd Taipei Taiwan R O C Company Address Taipei R O C Place Date Legal Signature of Authorized Person System Overview Chapter 1 System Overview PEB 3730VLA is designed based on Intel 855GME with high performance and high integration but low power consumption platform It is positioned at innovation high integration and high quality Embedded System Board in the embedded computing market The board is based on Intel 855GME chipset and latest high performance low power processor Intel Pentium M Processor running at up to 1 6Ghz with 400Mhz Process system bus and 90nm process technology with 533Mhz With Intel 855GME chipset that support high speed ECC DDR SDRAM high performance graphic controller AGP 4X controller with dual display Panel and Intel fast Ethernet connection enable Portwell PEB 3730 series to provide most versatile low power Embedded System Board ESB in the market All in all PEB 3730 series are designed to meet all kinds of low power embedded computing application With Intel most advance mainstream chipset for low power mobile computing 855GME PEB 3730VLA is aiming the low power mobile multimedia and networking applications in the market Its compact design with industry 5 25 ESB standard form factor makes it the most favorable solution for high den
13. II Compact Flash socket e Display controller Intel GMCH integrated graphics controller 855GME Integrated Intel Extreme graphics 2 Intel DVMT shared display memory up to 64MB DDR Memory Analog Display Support up to 2048 x 1536 60Hz refresh Multiplexed Digital Display Channels supports flat panels up to 2048x1536 60Hz or CRT HDTV at 1920 x 1080 x 18 amp 24bpp 85Hz AGP 4X 1 5V Intel Direct AGP Software DVD at 30 fps full screen Motion Video Acceleration Dual channel LVDS interface for LVDS Panel Display Support TMDS DVI port through daughter board Analogue and digital output through one DVI I connector on daughter board Panel Signal voltage must be 3 3V or 5V Inverter voltage 12V Dual LVDS ports possible thorough daughter board O System BIOS Award BIOS with PC 98 support 4Mbit flash ROM Intel FWH for easy upgrade Support DMI PnP Green function and ACPI default support ACPI support suspend to RAM USB wake up O Storage IDE Interface Support one enhanced IDE channel up to two HDDs or CD ROM support PIO 4 Ultra DMA 33 66 100 and Bus master feature e On Board YO I O Support four serial ports Parallel port support SPP EPP ECP Support four USB 2 0 Ports UHCI compliant Support one IrDA share one serial port e Hardware Monitoring Support CPU voltage temperature and FAN monitoring TBD O Watch Dog Timer Support Watch Dog Timer PEB 3730 373
14. Mouse Support Disabled Menu Level Init Display First Onboard AGP TJ Move Enter Select PU PD Value F10 Save ESC Bit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults USB Controller This item allows you to enable disable USB Universal Serial Bus function The choice Enabled Disabled USB 2 0 Controller This entry is for disable enable EHCI controller only This BIOS itself may may not have high speed USB support built in the support will be automatically turn on when high speed device were attached The choice Enabled Disabled USB Keyboard Support This item allows you to enable USB keyboard function under POST BIOS setup menu DOS or Windows NT with no USB driver loaded The choice Enabled Disabled USB Mouse Support This item allows you to enabled USB Mouse function under POST BIOS Setup menu DOS or Window NT with no USB driver loaded The choice Enabled Disabled PEB 3730 3732 Series User s Manual 4 15 BIOS Setup Information Init Display First This item allows you to select the first display port to be initialized The choice PCI Slot Onboard AGP Phoenix AwardBIOS CMOS Setup Utility Super IO Device Onboard FDC Controller Enabled Item Help Onboard Serial Port 1 3F8 TROQ4 Onboard Serial Port 2 2F8 IRQ3 UART Mode Select Normal Mente d X RxD TxD Active Hi Lo X IR Transmission Delay Enabled X UR2 Duplex Mod
15. Y N N Pressing Y loads the default values that are factory settings for optimal performance system operations 4 13 Supervisor User Password Setting You can set either supervisor or user password or both of then The differences between are Set Supervisor Password can enter and change the options of the setup menus Set User Password just can only enter but do not have the right to change the options of the setup menus When you select this function the following message will appear at the center of the screen to assist you in creating a password ENTER PASSWORD Type the password up to eight characters in length and press lt Enter gt The password typed now will clear any previously entered password from CMOS memory You will be asked to confirm the password Type the password again and press lt Enter gt You may also press lt Esc gt to abort the selection and not enter a password To disable a password just press lt Enter gt when you are prompted to enter the password A message will confirm the password will be disabled Once the password is disabled the system will boot and you can enter Setup freely PEB 3730 3732 Series User s Manual 4 26 BIOS Setup Information PASSWORD DISABLED When a password has been enabled you will be prompted to enter it every time you try to enter Setup This prevents an unauthorized person from changing any part of your system configuration Additionally when a pas
16. and SCO OpenServer 5 0 2 SCO Unixware 7 0 OS2 and Linux On board LED Indicator for LAN status PEB 3730 3732 series provides two LED indicators with RJ 45 connector to report Intel 82801BA MAC Fast Ethernet interfaces status Please refer to the table below as a quick reference guide Intel 82562EX Operation of Ethernet Port ese eae LAN speed LED 100 Mbps 10 Mbps LAN active LED Active No active No active Green LAN Link Integrity LED Active enger link in 10 or No link 100 Mbps There is no way to disable this onboard Ethernet function PEB 3730 3732 Series User s Manual 3 2 System Installation 3 4 Intel 82801DB AC 97 Codec Controller This on board Audio function is supported by Intel 82801DB ICH4 embedded AC 97 Codec Controller Drivers Support Please find Sound driver in Audio AC97 Realtek directory of PEB 3730 3732 series CD title The drivers support Windows NT 4 0 Windows 95 98 98SE Windows 2000 and Windows XP To disable this onboard Audio function please configure the Integrated Peripheral Setup Menu in BIOS Change the AC 97 Audio setting to Disabled will help you to turn off this PCI Audio device PEB 3730 3732 Series User s Manual 3 3 BIOS Setup Information Chapter 4 BIOS Setup Information PEB 3730 3732 series is equipped with the AWARD BIOS stored in Flash ROM The BIOS has a built in Setup program that allows users to modify the basic system configurati
17. bus architecture Enter for more options IRQ 3 IRQ 4 IRQ 5 IRQ 7 IRQ 9 TRQ 10 IRQ 11 IRQ 12 IRQ 14 IRQ 15 assigned to The choice PCI Device Reserved PCI VGA Palette Snoop Legacy ISA for devices compliant with the original PC AT bus specification PCI ISA PnP for devices compliant with the plug and play standard whether designed for PCI or ISA bus architecture The choice Enabled Disabled 4 10 PC Health Status Phoenix AwardBIOS CMOS Setup Utility PC Health Status CPU Warning Temperature Disabled Item Help Current System Temp 42 C 107 F Current CPU Temperature 38 C 100 F CPU FAN Speed 6750 RPM e te System FAN Speed 0 RPM CPU Vcore 1 45 V 1 05 V 1 04 V 3 3 V 3 26 V 5 V 4 99 V 12 V 11 91 V VBAT V 3 07 V 5VSB V 4 92 V CPU Throttle Temperature Disabled TJ Move Enter Select PU PD Value F10 Save ESC Bit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults PEB 3730 3732 Series User s Manual 4 24 BIOS Setup Information CPU Warning Temperature This item allows you to set a temperature above which the system will start the beeping warning Default setting is Disabled This function will only with ACPI power management and S3 STR suspend type The choices Disabled 50 C 122 F 53 C 127 F 56 C 133 F 60 C 140 F 63 C 145 F 66 C 151 F 70 C 158 F CPU Throttle Temperature This item a
18. mail us to get your download account number Portwell Download Center http www portwell com tw download as To request your Account Number for Download Center please fill out the information form on our Internet after selecting the information that you want PEB 3730 3732 Series User s Manual 5 4 Troubleshooting Note Please visit our technical web site at http www portwell com tw For additional technical information which isn t covered in this manual you can mail to tsdOmail portwell com tw or you can also send mail to our sales they will be very delighted to forward them to us PEB 3730 3732 Series User s Manual 5 5 Appendix A System Memory Address Map Each On board device in the system is assigned a set of memory addresses which also can be identical of the device The following table lists the system memory address used Memory Area Size Device Description 0000 003F 1K Interrupt Area 0040 004F 0 3K BIOS Data Area 0050 006F 0 5K System Data 0070 04C3 17K DOS 04C4 089B 15K Program Area 089C 9FFE 605K Available OFFF 9FFF 0 1K Unused Conventional memory ends at 640K A000 AFFF 64K VGA Graphics B000 B7FF 32K Unused B800 BFFF 32K VGA Text C000 CCDF 51K Video ROM CCEO CE49 5 7K Unused CE4A D7FF 38K High RAM D800 E7FF 64K Page Frame E800 EFFF 32K Unused F000 FFFF 64K System ROM HMA 64K First 64K Extended
19. 0 OOO Ber 22 2 11 B 5 we 0 TES ele con SS 88 ele 15 ee 55 BAT oo SA oo 00 1221 OO 120 OO 129 00 122 00 129 ei 00 QO OOF 20 Ors O oo Ip H 33 Ooo JP4 oo 109 OOO JPS DO ee OO 120 OO 120 88 88 So 29 SEH O OO Jig 35 Bae e do 33 SAS 88 JES Es a OO o 00000000 oon PEB 3730 PEB 3732 80 yy CN1 12 000 PEB 3730 3732 Series User s Manual 2 1 Hardware Configuration d 1 0 gt PEB 3730 PEB 3732 Figure 2 1 PEB 3730 3732 Series Jumper Location JP1 LVDS Panel Power Source Selector LVDS Panel VDD JP3 Power Source for CPU VCCA Selector CPU VCCA 1 8V for BANIAS 1 5V for DOTHAN JP4 Power Source for CPU VCCP Selector LVDS VCCP 1 2V for BANIAS 1 35V for DOTHAN PEB 3730 3732 Series User s Manual d 2 2 Hardware Configuration JP5 RTC CMOS Clear Jumper Setting Normal Operation Clear CMOS Contents JP6 LVDS Panel Resolution Selector OFF Disable LVDS Panel 5 6 1280 1024 18Bits 1 2 5 6 1280 1024 24Bits JP7 LVDS Panel Backlight Active Type Selector Backlight Power Active Type JP8 LVDS Panel Backlight Power Type Selector Backlight Power Type P9 COM2 RS 232 RS 422 485 Selector Jump Setting RS 232 5 6 9 11 10 12 15 17 16 18 RS 422 3 4 7 9 8 10 13 15 14 16 21 22 RS 485 1 2 7 9 8 10 19 20 x PEB 3730 3732 Series User s Manual 2 3 Hardware Configuration 2 2 Connector Allocation I O peripheral dev
20. 2 Series User s Manual 1 4 System Overview PCI Expansion Support one standard PCI slot EmbATX defined PCI slot with expansion capability through riser card up to 3 PCI slots PCI bus mastering On Board Ethernet Support 10 100 MB Base TX One ICH4 Integrated MAC controller with external 10 100 Mb phy 562 Support two LEDs to indicator LAN access and link status on RJ45 jack Audio AC97 v2 3 CODEC 1 8 photo jack for line in or microphone 1 8 photo jack for line out 4 pin stereo CDIN header for external CD line in ACPI compliant support the full on S0 Stop Grant S1 power management states if ATX power supply unit applied Real Time Clock Calendar RTC Compatible for 7 years of data retention to support real Y2K An external Li battery Overcurrent protection to comply with IEC 601 Power on off Soft on and 4 seconds override Header for connection to membrane switch Keyboard and PS 2 Mouse interface Support one mini DIN 6 pin connectors for keyboard and mouse Internal Connector IDE connector LCD LVDS interfaces LCD inverter interface PS 2 mouse connector 3 pin 0 10 pitch fan header 8 pin input power header 8 pin header for connection to membrane switch panel 2 pin reset header 10 pin header x2 for USB Physical and Environmental requirements Outline Dimension L x W 203mm X 146mm with Portwell standard 5 25 ESB dimension and mounting
21. 4X768 LVDS 1280X1024 LVDS 1400X1050 LVDS 1600X1200 LVDS Onboard AC97 Control This item allows you to enable AC97 Audio function The choice Enabled Disabled Onboard LAN Control This item allows you to enable LAN function The choice Enabled Disabled FWH Write Protection The choice Enabled Disabled 4 7 Integrated Peripherals Phoenix AwardBIOS CMOS Setup Utility Integrated Peripherals gt OnChip IDE Device Press Enter Item Help gt Onboard Device Press Enter gt Super IO Device Press Enter Menu Level gt TJ Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults PEB 3730 3732 Series User s Manual 4 13 BIOS Setup Information Phoenix AwardBIOS CMOS Setup Utility OnChip IDE Device On Chip Primary PCI IDE Enabled Item Help IDE Primary Master PIO Auto IDE Primary Slave PIO Auto M Level j IDE Primary Master UDMA Auto A O IDE Primary Slave UDMA Auto On Chip Secondary PCI IDE Enabled IDE Secondary Master PIO Auto IDE Secondary Slave PIO Auto IDE Secondary Master UDMA Auto IDE Secondary Slave UDMA Auto IDE HDD Block Mode Enabled N e Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults OnChip Primary Secondary PCI IDE The c
22. 732 Series User s Manual 1 2 System Overview 1 1 Check List The PEB 3730 3732 series package should include the following items v One Portwell Embedded System Board Y One User s Manual v One Installation Resources CD Title One optional cable set for system integration includes One IDE cable with 44pin to 40pin converter One FDC cable 2 0mm pitch One serial port cable with 2 connectors One USB cable 2 ports One parallel port cable One VGA cable One PS 2 keyboard and mouse cable One Fast Ethernet Cable One audio in out cable One I O connector extension board ATX power cable HDD and power indicator cable SO RON A e SONOROS SORES If any of these items is damaged or missing please contact your vendor and keep all packing materials for future replacement and maintenance 1 2 Product Specification PEB 3730VLA e Chipset Intel 855GME Intel GMCH and Intel ICH4 e CPU Intel Pentium M or Celeron M Support socket 478 Pentium M processor up to 1 8GHz FSB speed 400MHz easy upgrade to 533Mhz 1MB 2MB L2 cache Pentium M 2x32KB L1 cache O System memory One DIMM sockets Supports 200 266 333MHz DDR SDRAM up to 1GB Available bandwidth up to 2 1GB s DDR266 64 128 256 512 Mb SDRAM technologies PEB 3730 3732 Series User s Manual 1 3 System Overview 64bit non parity 2 5V DDR SDRAM support Registered DIMM not supported Support ECC functionality e SSD One type I or type
23. C PEB 3730 3732 Series User s Manual 4 11 BIOS Setup Information System BIOS Cacheable Selecting Enabled allows caching of the system BIOS ROM at F0000h FFFFFh resulting in better system performance However if any program writes to this memory area a system error may result The choice Enabled Disabled Video BIOS Cacheable Select Enabled to enable caching VGA BIOS into L2 cache to get higher display performance Disabled to ignore this BIOS caching function The choice Enabled Disabled Memory Hole At 15 16M In order to improve performance certain space in memory is reserved for ISA cards This memory must be mapped into the memory space below 16MB The choice Enabled Disabled Delayed Transaction Select Enabled to enable delay transaction This will enhance performance for data transmission between different PCI bus The choice Enabled Disabled Delay Prior to Thermal The choice 4 Min 8 Min 16 Min 32 Min AGP Aperture Size MB The choice 4 8 16 32 64 128 256 On Chip VGA The choice Enabled Disabled On Chip Frame Buffer Size Users can set the display memory size that shared from main memory The choice 1MB 4MB 8MB 16MB 32MB Boot Display The choice CRT LVDS CRT LVDS EFP CRT EFP PEB 3730 3732 Series User s Manual 4 12 BIOS Setup Information Panel Scaling The choice Auto On Off Panel Type The choice 640X480 LVDS 800X600 LVDS 102
24. CPU will be shut off The choice Disabled 1 Min 2 Min 4 Min 8 Min 12 Min 20 Min 30 Min 40 Min 1 Hour HDD Power Down When enabled and after the set time of system inactivity the hard disk drive will be powered down while all other devices remain active The choice Disabled 1 Min 2 Min 3 Min 4 Min 5 Min 6 Min 7 Min 8 Min 9 Min 10 Min 11 Min 12 Min 13 Min 14 Min 15 Min Soft Off by PWR BTTN This item allows users to set the time to remove the power after the power button is pressed The choice Instant Off Delay 4 Sec CPU THRM Throttling When the CPU temperature reaches the preset standard The CPU usage will be reduced to a selected level to avoid overheating The choice 82 5 75 0 62 5 50 0 37 5 25 0 12 5 Wake Up by PCI card This option can be enabled to support Wake Up by on board LAN The choice Disabled Enabled Power On by Ring When select Enabled a system that is at soft off mode will be alert to Wake On Modem The choice Enabled Disabled USB KB Wake up From S3 The choice Enabled Disabled PEB 3730 3732 Series User s Manual 4 21 BIOS Setup Information Resume by Alarm This item allows users to enable disable the resume by alarm function When Enabled is selected system using ATX power supply could be powered on if a customized time and day is approached The choice Enabled Disabled Date of Month Alarm When Resume by Alarm
25. DRAM chips installed so that greater delays may be required to preserve the integrity of the data held in the slower memory chips PEB 3730 3732 Series User s Manual 4 10 BIOS Setup Information DRAM Timing Selectable This option provides DIMM plug and play support by serial presence detect SPD mechanism via the system management bus SMBUS interface The choice Manual By SPD CAS Latency Time This option controls the number of SCLKs between the time a read command is sampled by the SDRAMs and the time the GMCH samples correspondent data from the SDRAMs The choice 2 2 5 Active to Precharge Delay This is to DDR standard accordingly The choice 5 6 7 DRAM RAS to CAS Delay This option controls the number of SCLKs SDRAM Clock from a row activate command to a read or write command If your system installs good quality of SDRAM you can set this option to 3 SCLKs to obtain better memory performance Normally the option will be set to Auto The choice 2 3 DRAM RAS Precharge This option controls the number of SCLKs for RAS precharge If your system installs good quality of SDRAM you can set this option to 3 SCLKs to obtain better memory performance It is set to auto normally The choice 2 3 DRAM Data Integrate Mode There are two options available The DRAM integrity mode will be implemented by the parity algorithm when this option is set to Non ECC The choice Non ECC EC
26. PEB 3730 3732 Series Embedded System Board User s Manual P N B8981070 Version 1 0 Copyright Portwell Inc 2004 All rights reserved All other brand names are registered trademarks of their respective owners Preface Table of Contents How to Use This Manual Chapter 1 System OvervVie Women 1 1 1 1 Check List lee ao 1 3 1 2 Product Specification tin a isa 1 3 1 2 Mechanical Dra Wi Berta li a eeh CEA s 1 9 1 3 System Architecture coccion ibi ee e E AAR 1 9 Chapter 2 Hardware Configuration oommomccoconnnccinnenncninnancnnnnnnncn crac rre 2 1 2 1 Jumper Setting intacta dla daa lolis 2 1 2 2 Connector Allocation testar dei 2 4 Chapter 3 System Installation cccesceccceeseceeeeeeeeseeeeeeeeeeeseeeseeeseeeseeeeseeseseseeeseseseanseseseenseeensees 3 1 3 1 INF Chipset Component Driver 3 1 3 2 Intel 855GM 852GME Graphics Controller A 3 1 3 3 Intel Fast Ethernet Controller esesenssscsssessesesesensnessenssessessesnesessesessnsvasvessesenesaesessnsesenss 3 2 3 4 Intel 82801DB AC 97 Codec Controller AAA 3 3 Chapter 4 BIOS Setup InformatioN oooomonmcocccncnnonnnnoncccncncnnnnnnnnnncnnnncnnnnnn EEN enn nn nn enn 4 1 4 LEntering SetuP esiin oct wagest suds sactoueeres ic 4 1 42 Maln Menu sariei eniai eine ta VAi aA n eee REE RAKLA RENEO AA REO ERANA AARE Ear EN AE EARE ERIAN APRN 4 2 4 3 Standard CMOS Setup Mem sanis tsn ieee E E R EENE E E E E 4 3 4 4 IDE Adaptors Setup Menu dee r Ee e haa dont essssessoes 4 5 4 5 A
27. Sector Virus Protection Status Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Date mm dd yy Tue May 18 2004 Item Help Time hh mm ss 10 29 50 IDE Primary Master Maxtor 52049H3 Menu Level S IDE Primary Slave None IDE Secondary Master None Change d daye monti gt IDE Secondary Slave None ee Drive A 1 44M 3 5 in Drive B None Video EVG VGA Halt On All But Keyboard Base Memory 640K Extended Memory 1014784K Total Memory 1015808K NW gt lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults PEB 3730 3732 Series User s Manual 4 3 BIOS Setup Information E Menu Selections Item Options Description Date mm dd yy Change the day month year and century Time hh mm ss Change the internal clock IDE Primary Options are in its sub Press lt Enter gt to enter the sub menu of Master menu detailed options IDE Primary Options are in its sub Press lt Enter gt to enter the next page for Slave menu detail hard drive settings IDE Secondary Options are in its sub Press lt Enter gt to enter the next page for Master menu detail hard drive settings IDE Secondary Options are in its sub Press lt Enter gt to enter the next page for Slave menu detail hard drive settings Drive A None Press lt Enter gt to enter the
28. aning of each setup parameters how to get advanced BIOS performance and update new BIOS In addition POST checkpoint list will give users some guidelines of trouble shooting Chapter 5 Troubleshooting Provides various useful tips to quickly get PEB 3730 3732 series running with success As basic hardware installation has been addressed in Chapter 3 this chapter will basically focus on system integration issues in terms of backplane setup BIOS setting and OS diagnostics The content of this manual and EC declaration document is subject to change without prior notice These changes will be incorporated in new editions of the document Portwell may make supplement or change in the products described in this document at any time Updates to this manual technical clarification and answers to frequently asked questions will be shown on the following web site http www portwell com Preface EC Declaration of Conformity To Be Added For the following equipment Product Name Model Name Trade Name is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive 89 336 EEC The equipment was evaluated and passed the test the following standards were applied EMC EN 55022 1994 A1 1995 Class A EN 50082 2 1991 EN 61000 4 2 1995 EN 61000 4 3 1996 EN 61000 4 4 1995 EN 61000 3 2 1995
29. bled Disabled UR2 Duplex Mode The available choices are full duplex mode and half duplex mode The choice Full Half Use IR Pins The available choices are IR Rx2Tx2 RxD2 TxD2 The choice IR Rx2Tx2 RxD2 TxD2 Onboard Parallel Port This item allows you to configure I O address of the onboard parallel port The choice Disabled 378 IRQ7 278 TRQ5 3BC IRQ7 Parallel Port Mode There are four different modes for the onboard parallel port SPP Switch to SPP mode EPP Switch to EPP mode ECP Switch to ECP mode ECP EPP Switch to ECP EPP mode PEB 3730 3732 Series User s Manual 4 17 BIOS Setup Information EPP Mode Select Select different version of EPP mode The choice EPP1 7 EPP1 9 ECP Mode Use DMA Select a proper DMA channel for ECP mode The choice 3 1 PWRON After PWR Fail This item allows user to configure the power status of using ATX power supply after a serious power loss occurs System automatically restores power back OFF System stays at power off Former Sts System restores back to previous status On or Off Watch Dog Timer Select This BIOS testing option is able to reset the system according to the selected table The choice Disabled 10 Sec 20 Sec 30 Sec 40 Sec 1 Min 2 Min 4 Min Onboard Serial Port 3 Port 4 The choice 3F8 2F8 3E8 2E8 Disabled Serial Port 3 Port4 Use IRQ The choice IRO10 IRQ11 IRQ3 IRO4 IRO5 IRQ7 IRQ9 PEB 3730 3732 Ser
30. bus and the PCI bus It must be stated that these items should never need to be altered The default settings have been chosen because they provide the best operating conditions for your system The only time you might consider making any changes would be if you discovered that data was being lost while using your system Phoenix AwardBIOS CMOS Setup Utility Advanced Chipset Features DRAM Timing Selectable By SPD Item Help X CAS Latency Time 2 X Active to Precharge Dela 6 X DRAM RASH to CASH GE 3 Menor R X DRAM RAS Precharge 3 DRAM Data Integrity Mode Non ECC System BIOS Cacheable Enabled Video BIOS Cacheable Disabled Memory Hole At 15M 16M Disabled Delayed Transaction Enabled Delay Prior to Thermal 16 Min AGP Aperture Size MB 64 On Chip VGA Setting On Chip VGA Enabled On Chip Frame Buffer Size 32MB Boot Display CRT Panel Scaling Auto Panel Type 640X480 LVDS Onboard AC97 Control Enabled Onboard LAN Control Enabled FWH Write Protection Enabled N e Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults This chipset settings deal with CPU access to dynamic random access memory DRAM The default timings have been carefully chosen and should only be altered if data is being lost Such a scenario might well occur if your system had mixed speed
31. ctor MIC Line IN Line OUT Interface Connector BUZZER Connector LAN2 Connector PEB 3730VLA amp PEB 3732VLA NONE Thermal Sense Interface Connector Optional IDE1 Interface Connector Front Panel Connector LVDS Inverter Connector LAN1 Connector GPIO Interface Connector PS 2 Keyboard Mouse Connector Compact Flash Connector DVI Interface Connector VGA Connector Pin Assignments of Connectors CN1 ATX Power Connector Signal Description 5V 5V 5VSB 12V PS ON GND GND ATX PWROK CO NI OD OT G2 Nf A CN2 1394 Connector PS PEB 3730VLA amp PEB 3732VLA NONE Signal Description 12V GND Port B Port B Port A Port A PEB 3730 3732 Series User s Manual 2 5 Hardware Configuration J1 COM Portl COM Port2 COM Port3 COM Port4 Connector Signal Description Signal Description COM1 DCD COM1 DSR COM1 RXD COM1 RTS COM1 TXD COM1 CTS COM1 DTR COM1 RI COM1 GND NC COM2 DCD RS 485 TX COM2 DSR COM2 RXD RS 485 TX COM2 RTS COM2 TXD RS 422 RX COM2 CTS COM2 DTR RS 422 RX COM2 RI COM2 GND NC COM3 DCD COM3 DSR COM3 RXD COMB RTS COM3 TXD COMB CTS COM3 DTR COM3 RI COM3 GND NC COM4 DCD COM4 DSR COM4 RXD COMA4 RTS COM4 TXD COM4 CTS COM4 DTR COMA4 RI COM4 GND NC
32. discuss about BIOS setting OS diagnostics and system integration issues 5 1 BIOS Setting It is assumed that users have correctly adopted modules and connected all the device cables required before turning on AT power CPU CPU fan CPU fan power cable 184 pin DDR SDRAM keyboard mouse floppy drive IDE hard disk printer VGA connector device power cables ATX accessories or 12V 4 pin power cable are good examples that deserve attention With no assurance of properly and correctly accommodating these modules and devices it is very possible to encounter system failures that result in malfunction of any device To make sure that you have a successful start with PEB 3730 3732 series it is recommended when going with the boot up sequence to hit DEL key and enter the BIOS setup menu to tune up a stable BIOS configuration so that you can wake up your system far well Loading the default optimal setting When prompted with the main setup menu please scroll down to Load Optimal Defaults press Enter and Y to load in default optimal BIOS setup This will force your BIOS setting back to the initial factory configuration It is recommended to do this so you can be sure the system is running with the BIOS setting that Portwell has highly endorsed As a matter of fact users can load the default BIOS setting any time when system appears to be unstable in boot up sequence Auto Detect Hard Disks In the BIOS gt Standa
33. dvanced BIOS FeatlreSinnn aiii 4 6 4 6 Advanced Chipset Features nei nine iera E ala ia ica 4 10 4 7 Integrated Peripherals ui AAA 4 13 4 8 Power Management SetUP ee Zoe SEENEN ati Eeer 4 19 4 9 PnP PCL CONSUL ON ind ae 4 23 Ee ER EE 4 24 4 11 Frequency Voltage Control see NEEN iia 4 25 4 12 Default Men uan ta tl datada 4 26 4 13 Supervisor User Password Setting ENEE 4 26 A 14 Exiting EE 4 27 Chapter 5 Trouble ShootiNg cocida 5 1 Dil BIOS SEO iii dia a da cles teases so sede EEEREN EEIEIEE EAS EEAS 51 LAA O asia di 5 3 Appendix A System Memory Address Map Appendix B Interrupt Request Lines IRQ Preface How to Use This Manual The manual describes how to configure your PEB 3730 3732 series system to meet various operating requirements It is divided into five chapters with each chapter addressing a basic concept and operation of Single Board Computer Chapter 1 System Overview Presents what you have in the box and give you an overview of the product specifications and basic system architecture for this series model of single board computer Chapter 2 Hardware Configuration Shows the definitions and locations of Jumpers and Connectors that you can easily configure your system Chapter 3 System Installation Describes how to properly mount the CPU main memory and Compact Flash to get a safe installation and provides a programming guide of Watch Dog Timer function Chapter 4 BIOS Setup Information Specifies the me
34. e Half X Use IR Pins IR Rx2Tx2 Onboard Parallel Port 378 IRQ7 Parallel Port Mode SPP X EPP Mode Select EPP1 7 X ECP Mode Use DMA 3 PWRON After PWR Fail Off Watch Dog Timer Select Disabled Onboard Serial Port 3 3E8 Serial Port 3 Use IRQ IRQ10 Onboard Serial Port 4 2E8 Serial Port 4 Use IRQ RQ11 N e Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Onboard FDC Controller This item allows you to enable disable onboard Floppy disk controller The choice Enabled Disabled Onboard Serial Port 1 Port 2 Select an address and corresponding interrupt for the first and second serial ports The choice 3F8 IRQ4 2E8 IRQ3 3E8 IRQ4 2F8 IRQ3 Disabled Auto PEB 3730 3732 Series User s Manual 4 16 BIOS Setup Information UART Mode Select This item allows users to select Infrared transmission mode Normal Disable Infrared function Select IrDA mode transmission ASKIR Select ASKIR mode transmission RxD TxD Active This item is to configure Infrared transmission rate Four options are available High rate for receiving High rate for transmitting High rate for receiving Low rate for transmitting Low rate for receiving High rate for transmitting Low rate for receiving Low rate for transmitting IR Transmission Delay This option will be available when IR is enabled The choice Ena
35. ether it inserts properly Beep rapidly Power error warning Please check Power mode setting Information Support Q I am using an ATA 66 or 100 hard drive how can I know that ATA 66 function is started A First of all you need to use the 80 pin ATA 66 IDE flat cable to have this function ready During POST you can see ATA 66 or 100 message while hard drive is being detected Besides after Microsoft series OS installation successfully you must install ATA 66 100 driver then the function can be active Q How can I connect my PEB 3730 3732 series to panel A First of all you need to read the Panel spec and Inverter spec to understand which type of panel you will use on PEB 3730 3732 series different panel will connect to different connector LVDS is J14 and DVO is J34 PEB 3730 3732 Series User s Manual 5 3 Troubleshooting Q I am using an ATA 66 or 100 hard drive how can I know that ATA 66 100 is A active As matter of fact you need to use 80 pins ATA 66 IDE cable to enable ATA 66 function While POST stage of detecting hard drive you will see ATA 66 100 messages Besides after installing Microsoft Windows system you also need to install ATA 66 100 driver Otherwise this function won t be active in Windows After setting up my serial port from RS 232 to RS 485 why my serial port still cannot work Unlike RS 232 RS 485 signal is differential signal and only two pins DATA and DATA
36. hipset contains a PCI IDE interface with support for two IDE channels Select Enabled to activate the primary IDE interface Select Disabled to deactivate this interface The choice Enabled Disabled IDE Primary Secondary Master Slave PIO The four IDE PIO Programmed Input Output fields let you set a PIO mode 0 4 for each of the four IDE devices that the onboard IDE interface supports Modes O through 4 provide successively increased performance In Auto mode the system automatically determines the best mode for each device The choice Auto Mode 0 Mode 1 Mode 2 Mode 3 Mode 4 IDE Primary Secondary Master Slave UDMA Ultra DMA 33 66 100 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver Windows 95 OSR2 or a third party IDE bus master driver If your hard drive and your system software both support Ultra DMA 33 66 100 select Auto to enable BIOS support The choice Auto Disabled PEB 3730 3732 Series User s Manual 4 14 BIOS Setup Information IDE HDD Block Mode If your IDE hard drive supports block mode select Enabled for automatic detection of the optimal number of block read writes per sector the drive can support The choice Enabled Disabled Phoenix AwardBIOS CMOS Setup Utility Onboard Device USB Controller Enabled Item Help USB 2 0 Controller Enabled USB Keyboard Support Disabled USB
37. ible thorough daughter board System BIOS Award BIOS with PC 98 support 4Mbit flash ROM Intel FWH for easy upgrade Support DMI PnP Green function and ACPI default support ACPI support suspend to RAM USB wake up PEB 3730 3732 Series User s Manual 1 6 System Overview O Storage IDE Interface Support one enhanced IDE channel up to two HDDs or CD ROM support PIO 4 Ultra DMA 33 66 100 and Bus master feature IDE header x1 e On Board YO I O Support four serial ports for UART Parallel port support SPP EPP ECP Support four USB 2 0 Ports four panel mount connectors UHCI compliant Support one IrDA share one serial port One IEEE 1394A fire wire port This function is optional only for PEB 3732VL2A model e Hardware Monitoring Support CPU voltage temperature and FAN monitoring e Watch Dog Timer Support Watch Dog Timer e PCI Expansion Support one standard PCI slot EmbATX defined PCI slot with expansion capability through riser card up to 3 PCI slots PCI bus mastering e On Board Ethernet Support 10 100 MB Base TX One ICH4 Integrated MAC controller Support Wake on LAN e IEEE 1394 optional only for PEB 3732VL2A by project PCI 1394a integrated Host controller 1394a OHCI Link Layer controller with integrated 400Mbit 2 port PHY Supports provisions of IEEE 1394 1995 standard for high performance serial bus and P1394a supplement 4 0 6 pin header for 2 IEEE 1394 Por
38. ices and flash disk are connected to the interface connectors and CF socket on this board computer Figure 2 2 D 129 Sop pocoo lee SSO SSSSSSGG E 3157 GC GC ee Se sta OCH GC GC OO GC oo GC GC ee GC OO 34 CODO OOOO OO OOOOOODODOn OOOO OOOO JZ JA EC a3 OOOO OOOOOO OO OOO JP 335 Blo oo 00990 00000 CoN 0006000 Ooo a J24 ao 5 20 OD RSS SEI CK OKIE Soo ss OOO JPL 28 28 qi B we mi TFB OO con SS 88 Qe m5 28 Codec BAT oo 2 8 D Bo tela HE FWH OO 102 00 109 Oo 102 OO 120 de 00 QO 28 MN OO IPS SS NN COD JP4 So Leite Cono JPS OO 122 00 120 SG 199 oo S OG ISS Un re 0072 a los o Lee CPU O Lee 8 83 o 155 OO En ee Se o MES SE GE escoa D een E 000000 Gol CN2 88 88 83 gt OOO OO OOO oon PEB 3730 PEB 3732 80 yy CNI J12 O00 Figure 2 2 PEB 3730 3732 Series Connector Location Connector Function List ATX Power Connector 1394 Connector PEB 3730VLA amp PEB 3732VLA NONE COM Port1 COM Port2 COM Port3 COM Port4 Connector FDC Interface Connector Power ON OFF IDE1 Campact Flash Active LED System Reset Header USB Port1 USB Port2 Interface Connector USB Port3 USB Port4 Interface Connector Front Panel SMBUS Header PEB 3730 3732 Series User s Manual 2 4 Hardware Configuration CD IN Connector System FAN Connector IR Connector LVDS Interface Connector CPU FAN Conne
39. ies User s Manual 4 18 BIOS Setup Information 4 8 Power Management Setup The Power Management Setup allows you to configure you system to most effectively save energy while operating in a manner consistent with your own style of computer use Phoenix AwardBIOS CMOS Setup Utility Power Management Setup ACPI Function Enabled Item Help ACPI Suspend Type S1 POS X Run VGABIOS if S3 Resume Auto Power Management User Define Menu Level d Video Off Method DPMS Video Off In Suspend Yes Suspend Type Stop Grant Suspend Mode Disabled HDD Power Down Disabled Soft Off by PWR BTTN Instant Off CPU THRM Throtting 50 Wake up by PCI card Disabled Power On by Ring Disabled X USB KB Wake Up FromS3 Disabled Resume by Alarm Disabled X Date of Month Alarm 0 X Time hh mm ss Alarm 0 0 0 Reload Global Timer Events Primary IDE 0 Disabled Primary IDE 1 Disabled Secondary IDE 0 Disabled Secondary IDE 1 Disabled FDD COM LPT Port Disabled PCI PIRQ A D Disabled N e Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults ACPI Function This item allows you to enable disable the Advanced Configuration and Power Management ACPI The choice Enabled Disabled PEB 3730 3732 Series User s Manual 4 19 BIOS Setup Information ACPI Suspend Type To decide which ACPI suspend mode to
40. ings Phoenix AwardBIOS CMOS Setup Utility PnP PCI Configurations Reset Configuration Data Disabled Item Help Resources Controlled By Auto ESCD X IRQ Resources Press Enter Menu Level S PCI VGA Palette Snoop Disabled Default is Disabled Select Enabled to reset Extended System Configuration Data ESCD when you exit Setup if you have installed a new add on and the system reconfiguration has caused such a serious conflict that the OS cannot boot N e Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Reset Configuration Data Default is Disabled Select Enabled to reset Extended System Configuration Data ESCD when you exit Setup if you have installed a new add on and the system reconfiguration has caused such a serious conflict that the OS cannot boot The choice Enabled Disabled Resource Controlled By BIOS can automatically configure all the boot and plug and play compatible devices If you choose Auto you cannot select IRQ DMA and memory base address fields since BIOS automatically assigns them The choice Auto ESCD Manual PEB 3730 3732 Series User s Manual 4 23 BIOS Setup Information IRO Resources Legacy ISA for devices compliant with the original PC AT bus specification PCIISA PnP for devices compliant with the Plug AND play standard whether designed for PCI or ISA
41. isabled There is no way to disable this onboard video function unless one off board PCI video card is applied onto the backplane In this case the off board video card shall be picked up first based on the default BIOS setup Initial Display First in Integrated Peripheral Setup Menu Drivers Support Please find Intel 855GM 852GME driver in Graphics directory of PEB 3730 3732 series CD title Drivers support Windows 95 98 98SE ME Windows NT 4 0 Windows 2000 OS2 and Linux 1 Windows 95 98 98SE ME Please execute Graphicl Intel Extreme win9x1 win9x1361 exe to start graphics driver installation PEB 3730 3732 Series User s Manual 3 1 System Installation 2 Windows NT 4 0 Please execute Graphicl Intel Extreme WinNT4 winnt41361 exe to start graphics driver installation 3 Windows 2000 XP Please execute Graphic Intel Extremel Win2KXP win2k_xp141 exe to start graphics driver installation 4 Redhat Linux V6 2 Please refer to the 20030425 i386 txt file in Graphic Intell Extreme Linux directory for graphics drivers installation guide 3 3 Intel Fast Ethernet Controller This Fast Ethernet function is supported by Intel 82562 82551 82540 embedded PHY and interfaced via Intel 82562EX Platform LAN Connect PLC Drivers Support Please find LAN driver in Ethernet Intel PRO directory of PEB 3730 3732 series CD title The drivers support Windows NT 3 51 4 0 Windows 95 98 98SE ME Windows 2000
42. llows you to set a temperature above which the system will operate in lower speed immediately Default setting is Disabled This function will only with ACPI power management and S3 STR suspend type The choice Disabled 60 C 140 F 65 C 149 F 70 C 158 F 75 C 167 F 4 11 Frequency Voltage Control Phoenix AwardBIOS CMOS Setup Utility Frequency Voltage Control Auto Detect DIMM PCI Clk Enabled Item Help Spread Spectrum Disabled Menu Level gt N e Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Auto Detect PCI Clk The choice Enabled Disabled Spread Spectrum This item allows you to enable disable the spread spectrum modulate The choice Enabled Disabled PEB 3730 3732 Series User s Manual 4 25 BIOS Setup Information 4 12 Default Menu Selecting Defaults from the main menu shows you two options which are described below Load Fail Safe Defaults When you press lt Enter gt on this item you get a confirmation dialog box with a message similar to Load Fail Safe Defaults Y N N Pressing Y loads the BIOS default values for the most stable minimal performance system operations Load Optimized Defaults When you press lt Enter gt on this item you get a confirmation dialog box with a message similar to Load Optimized Defaults
43. next page for Drive B 360K 5 25 in detail hard drive settings 1 2M 5 25 in 720K 3 5 in 1 44M 3 5 in 2 88M 3 5 in Video EGA VGA Select the default video device CGA 40 CGA 80 MONO Halt On All Errors Select the situation in which you want the No Errors BIOS to stop the POST process and notify All But Keyboard you All But Diskette All But Disk Key Base Memory 640K Displays the amount of conventional memory detected during boot up Extended N A Displays the amount of extended memory Memory detected during boot up Total Memory N A Displays the total memory available in the system PEB 3730 3732 Series User s Manual 4 4 BIOS Setup Information 4 4 IDE Adaptors Setup Menu The IDE adapters control the IDE devices such as hard disk drive or CDROM drive It uses a separate sub menu to configure each hard disk drive Phoenix AwardBIOS CMOS Setup Utility IDE Primary Master IDE HDD Auto Detection Press Enter Item Help IDE Primary Master Auto Set Y Access Mode Auto Menu Leve To atuo detect the HDD s Capacit 20492MB pasi size head on this Cylinder 39704 SE Head 16 Precomp 0 Landing Zone 39703 Sector 63 N e Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults E Menu Selections Item Options Description IDE HDD Auto Press Enter Press Enter to auto detect
44. on easily This type of information is stored in CMOS RAM so that it retained during power off periods When system is turned on PEB 3730 3732 series communicates with peripheral devices and check its hardware resources against the configuration information stored in the CMOS memory If any error detected or the CMOS parameters need to be initially defined the diagnostic program will prompt the user to enter the SETUP program Some errors are significant enough to abort the start up 4 1 Entering Setup Turn on or reboot the computer When the message Hit lt DEL gt if you want to run SETUP appears press lt Del gt key immediately to enter BIOS setup program If the message disappears before you respond but you still wish to enter Setup please restart the system to try COLD START again by turning it OFF and then ON or touch the RESET button You may also restart from WARM START by pressing lt Ctrl gt lt Alt gt and lt Delete gt keys simultaneously If you do not press the keys at the right time and the system will not boot an error message will be displayed and you will again be asked to Press lt F1 gt to Run SETUP or Resume In HIFLEX BIOS setup you can use the keyboard to choose among options or modify the system parameters to match the options with your system The table below will show you all of keystroke functions in BIOS setup F Menu in BIOS 1 2 5 6 5 e 10 PEB 3730 3732 Series Use
45. or Resistor Thermal Sensor Resistor PEB 3730 3732 Series User s Manual 2 9 Hardware Configuration J21 IDE1 Interface Connector PIN No Signal Description PIN No Signal Description RESETH GND Signal Description 5V Power LED Key lock GND J27 LVDS Inverter Connector Signal Description 12V GND GND 5V SMBCLK LVDS Backlight LVDS Enable PEB 3730 3732 Series User s Manual 2 10 Hardware Configuration J29 LAN1 Connector Signal Description MDI Signal Description MDI LAN1 BI_DA LAN1 BI D n LAN1 BI D 4 LAN1 BI_DB LAN1 BL_DC 6 LANIBIDC LAN1BI_DD 8 LANIBLDD PIN No Signal Description 1 GPI 4 ESE GPI7 PIN No Signal Description PIN No Signal Description Mouse Data 2 Keyboard Data 4 1 4 IN a PIN No Signal Description G 25 GND a De 2 9 H ATASEL o O PEB 3730 3732 Series User s Manual 2 11 Hardware Configuration 134 DVI Interface Connector PIN No Signal Description PIN No Signal Description 1 NC 2 NC ME NG NC NC NC O NC DVO Detect 6 peo pes E E DvocDii 12 DVODetect DvocDio LH DVOBCINTR pDvocD9 Lie DVOCBlank DVOCD8 LN DVOCD7 Lu Rest DVOCD6 LN pDvocDS LX PCData DvocD4 TGC Clock pDvocD3 BBV DNOCD Lu BV pbvocD1 La py DVOcDo LN GND 5V O L 28 DVOCHSYNC EXA ESOS EE A ao vc GND
46. r s Manual 4 1 BIOS Setup Information 4 2 Main Menu Once you enter PEB 3730 3732 series AWARD BIOS CMOS Setup Utility you should start with the Main Menu The Main Menu allows you to select from eleven setup functions and two exit choices Use arrow keys to switch among items and press lt Enter gt key to accept or bring up the sub menu Phoenix AwardBIOS CMOS Setup Utility gt Standard CMOS Features gt Advanced BIOS Features gt Advanced Chipset Features gt Integrated Peripherals gt Power Management Setup gt PnP PCI Configurations gt PC Health Status gt Frequency Voltage Control Load Fail Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save amp Exit Setup Exit Without Saving ESC Quit F10 Save amp Exit Setup Hi gt Select Item Time Date Hard Disk Type Note It is strongly recommended to reload Optimal Setting if CMOS is lost or BIOS is updated PEB 3730 3732 Series User s Manual 4 2 BIOS Setup Information 4 3 Standard CMOS Setup Menu This setup page includes all the items in a standard compatible BIOS Use the arrow keys to highlight the item and then use the lt PgUp gt lt PgDn gt or lt gt lt gt keys to select the value or number you want in each item and press lt Enter gt key to certify it Follow command keys in CMOS Setup table to change Date Time Drive type and Boot
47. rd CMOS setup menu pick up any one from Primary Secondary Master Slave IDE ports and press Enter Setup the selected IDE port and its access mode to Auto This will force system to automatically pick up the IDE devices that are being connected each time system boots up Improper disable operation There are too many occasions where users disable a certain device feature in one application through BIOS setting These variables may not be set back to the original values when needed These devices features will certainly fail to be detected PEB 3730 3732 Series User s Manual 5 1 Troubleshooting When the above conditions happen it is strongly recommended to check the BIOS settings Make sure certain items are set as they should be These include the floppy drive COM1 COM2 ports parallel port USB ports external cache on board VGA and Ethernet It is also very common that users would like to disable a certain device port to release IRQ resource A few good examples are Disable COM1 serial port to release IRQ 4 Disable COM2 serial port to release IRQ 3 Disable COM3 serial port to release IRQ 10 Disable COM4 serial port to release IRQ 11 Disable parallel port to release IRQ 7 etc A quick review of the basic IRQ mapping is given below for your reference IRQ Description IRQ 0 System Counter IRQ 1 Keyboard IRQ 3 COM2 IRQ 4 COM1 IRQ 5 Display Cont
48. roller IRQ 5 USB 1 0 1 1 IRQ 5 USB 2 0 IRQ 5 Ethernet Controller IRQ 6 Floppy Disk Controller IRQ 7 Printer Port Parallel Port IRQ 8 System CMOS Real time Clock IRQ 9 Multimedia Controller IRQ 9 SMBus Controller IRQ 9 Serial Bus Controller IRQ 9 Ethernet Controller IRQ 9 IEEE 1394 Controller IRQ 9 ACPI Controller IRQ 10 COM3 IRQ 11 COM4 It is then very easy to find out which IRQ resource is ready for additional peripherals If IRQ resource is not enough please disable some devices listed above to release further IRQ numbers PEB 3730 3732 Series User s Manual 5 2 Troubleshooting 5 2 FAQ Unboot issues Symptom After installing CPU and cable all required but why my Embedded board is still not working Solution First of all please double check if your CPU is installed and fasten on CPU socket properly Otherwise Embedded board will result in failure booting up Symptom My PEB 3730 3732 series just keeps beeping and nothing has been shown on the screen Solution As a matter of fact each beep sound represents different definition of error message Therefore please refer to the table as follow Beep sounds Meaning Action One long beep with one DRAM error Change DRAM or reinstall it short beeps One long beep constantly DRAM error Change DRAM or reinstall it One long beep with two Monitor or Display Please check Monitor connector short beeps Card error wh
49. sity server High reliability compact size and easy to use features fulfill the demand for critical embedded and Interactive client application including Wearable computing Heath care Vehicle POS KIOSK ATM Gaming and medical application Key Features e Compact 5 25 ESB form factor to fit in most wide range of system architecture O Intel new generation mobile longevity chipset Intel 855GME powered by Pentium M with frequencies of up to 2 0GHz with uFC PGA socket 478 for easy processor configuration e Dual independent on board display support CRT LVDS and DVO for other display possibility like DVI e On board standard I O display LVDS panel network and audio to meet the requirements of interactive client platform e On board 10 100BASE TX Ethernet to provide network connection e Up to 1GB high performance DIMM DDR SDRAM allows to run versatile embedded programs but keep lower profile for slim system design for ultra low voltage model e One PCI with PCI expansion capability defined by EmbATX One Type II CF socket for 8 320MB Compact Flash disk to provide space of resident system setting data and software PEB 3730 3732 Series User s Manual 1 1 System Overview PEB 3732 series Portwell also provide a ultra low power model with Intel Celeron M 600Mhz processor since this model adopt uFC BGA2 packaged processor we only provide a default model as PEB 3732VLA PEB 3732VLA is based on Intel 852GM with ultra low vol
50. sword is enabled you can also require the BIOS to request a password every time your system is rebooted This would prevent unauthorized use of your computer You determine when the password is required within the BIOS Features Setup Menu and its Security option see Section 3 If the Security option is set to System the password will be required both at boot and at entry to Setup If set to Setup prompting only occurs when trying to enter Setup 4 14 Exiting Selection Save amp Exit Setup Pressing lt Enter gt on this item asks for confirmation Save to CMOS and EXIT Y N Y Pressing Y stores the selections made in the menus in CMOS a special section of memory that stays on after you turn your system off The next time you boot your computer the BIOS configures your system according to the Setup selections stored in CMOS After saving the values the system is restarted again Exit Without Saving Pressing lt Enter gt on this item asks for confirmation Quit Without Saving Y N N This allows you to exit Setup without storing in CMOS any change The previous selections remain in effect This exits the Setup utility and restarts your computer PEB 3730 3732 Series User s Manual 4 27 Troubleshooting Chapter 5 Trouble shooting Due to the fact that detailed hardware installation and Pins definition on PEB 3730 3732 series have been addressed on early Chapters of this manual this Chapter will mainly
51. t Audio AC97 v2 3 CODEC 1 8 photo jack for line in or microphone 1 8 photo jack for line out 4 pin stereo CDIN header for external CD line in e ACPI compliant support the full on S0 Stop Grant S1 power management states if ATX power supply unit applied PEB 3730 3732 Series User s Manual 1 7 System Overview Real Time Clock Calendar RTC Compatible for 7 years of data retention to support real Y2K An external Li battery Overcurrent protection to comply with IEC 601 Power on off Soft on and 4 seconds override Header for connection to membrane switch Keyboard and PS 2 Mouse interface Support one mini DIN 6 pin connectors for keyboard and mouse Internal Connector IDE connector LCD LVDS interfaces LCD inverter interface PS 2 mouse connector 3 pin 0 10 pitch fan header 8 pin input power header 8 pin header for connection to membrane switch panel 2 pin reset header 10 pin header x2 for USB 6 pin header for 2 IEEE 1394 Port optional Physical and Environmental requirements Outline Dimension L x W 203mm X 146mm Power requirements TBD Operating temperature 0 to 55 C Relative Humidity 5 to 95 non condensing PEB 3730 3732 Series User s Manual 1 8 System Overview 1 2 1 Mechanical Drawing O GI i
52. tage Celeron M processor It is positioned at cost effective and low power fan less Embedded System Board in the growing embedded computing market The board is based on Intel 852GM chipset and latest Intel low power processor Intel Celeron M Processor running at 600Mhz with 400Mhz Process system bus With Intel 852GM chipset that support high speed ECC DDR SDRAM high performance graphic controller AGP 4X controller with dual display Panel and dual Intel fast Ethernet connection enable Portwell PEB 3732 series to provide most versatile low power Embedded System Board ESB in the market Key Features e Compact 5 25 ESB form factor to fit in most wide range of system architecture O Intel new generation mobile longevity chipset Intel 852GM powered by ULV Celeron M 600 Mhz with uFC BGA direct mount to board e Dual independent on board display support CRT LVDS and DVO for other display possibility e On board standard I O display LVDS panel network and audio to meet the requirements of interactive client platform e On board 10 100BASE TX Ethernet to provide network connection e Up to 1GB high performance DIMM DDR SDRAM allows to run versatile embedded programs but keep lower profile for slim system design for ultra low voltage model e One PCI with PCI expansion capability defined by EmbATX e One Type II CF socket for 8 320MB Compact Flash disk to provide space of resident system setting data and software PEB 3730 3
53. the HDD on this detection channel If detection is successful it fills the remaining fields on this menu IDE Primary None Selecting manual lets you set the Master Auto remaining fields on this screen Selects the Manual type of fixed disk User Type will let you select the number of cylinders heads etc Note PRECOMP 65535 means NONE Access Mode CHS Choose the access mode for this hard disk LBA Large Auto Capacity Auto Display your Disk drive capacity Approximated disk drive size Note that this size is usually slightly greater than the size of a formatted disk given by a disk checking program Manual The following options are selectable only if the IDE Primary Master item is set to Cylinder Min 0 Set the number of cylinders for this hard PEB 3730 3732 Series User s Manual 4 5 BIOS Setup Information Max 65535 disk Head Min 0 Set the number of read write heads Max 255 Precomp Min 0 Warning Setting a value of 65535 Max 65535 means no hard disk Landing zone Min 0 CSC Max 65535 Sector Min 0 Number of sectors per track Max 255 4 5 Advanced BIOS Features This section allows you to configure your system for basic operation You have the opportunity to select the system s default speed boot up sequence keyboard operation shadowing and security Phoenix AwardBIOS CMOS Setup Utility Advanced BIOS Features
54. use The choice SI POS S3 STR 1 amp S3 Run VGA BIOS if S3 Resume The choice Auto Yes No Power Management This category allows you to select the type or degree of power saving and is directly related to HDD Power Down Suspend Mode There are three selections for Power Management three of which have fixed mode settings Min Power Saving Minimum power management Suspend Mode 1 Hour and HDD Power Down 15 Min Max Power Saving Maximum power management Suspend Mode 1 Mim and HDD Power Down 1 Min User Defined Allows you to set each mode individually When not disabled Suspend Mode ranges from 1 min to 1 Hour and HDD Power Down ranges from 1 Min to 15 Min Video Off Method This determines the manner in which the monitor is blanked V H SYNC Blank This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer Blank Screen This option only writes blanks to the video buffer DPMS Initial display power management signaling Video Off In Suspend This allows user to enable disable video off in Suspend Mode The choice Yes No Suspend Type Two options are available Stop Grant and PwrOn Suspend The choice Stop Grant PwrOn Suspend PEB 3730 3732 Series User s Manual 4 20 BIOS Setup Information Suspend Mode When enabled and after the set time of system inactivity all devices except the
55. will be used As for connection of RS 485 its DATA and DATA must connect to the same definition pin For instance DATA must connect to another device s DATA DATA must connect to another device s DATA Otherwise RS 485 won t be able to transfer its data to another device Moreover while creating RS 485 cable two data wires must be twisted together to prevent its signal from being nosed After installing Compact Flash why the device on Secondary has been missing In fact the default setting for Compact Flash at Secondary Channel is master Therefore you might want to check if your missing device is set to the same as its default setting master If it is you must set up your device to slave at Secondary Channel to avoid the devices confliction I am a developer of the embedded system but I cannot find embedded driver on Portwell website or CD Where can I get them Indeed for Intel Chipset It is available on Intel website here is hyperlink of Intel website http www intel com design intarch software driver index htm For other devices please visit their website to download those embedded drivers However we will put those drivers on our website in future and CD Q I am a customer of Portwell where can I get a new BIOS to update my SBC A Indeed you can always go to Portwell Download center to download update BIOS Besides before downloading anything please
Download Pdf Manuals
Related Search