Gasboy CFN Series Site Controller III Technician`s Guide
Contents
1. may be directed to them LPT1 2 can only be used as log printers or command output The SCIII has one more RS422 channel available than the SCII This has been assigned to be another island loop Broadcast messages will be sent to both of these channels The POS loop is the only loop that Profit Points can be connected to The following is a list of ports and their assignments Gasboy CFN Series SC III Technician s Guide Site Controller III Ports and Switches 13 Name Channel Location Function CON 0 PC CRT Keyboard Local port login SCI 1 COMM CPU top DIN RS232 SC2 2 COMM CPU 26 pin ribbon RS232 all cont lines SC3 3 COMM MEM DB 9 Tokheim pumps SC4 4 COMM MEM bottom DIN RS232 SC5 5 COMM MEM middle DIN RS232 SC6 6 COMM MEM top DIN RS232 COMI 7 PC RS232 COM2 8 PC RS232 COM3 9 PC RS232 COM4 10 PC RS232 LPTI 11 PC Parallel output LPT2 12 PC Parallel output LOOPI N A COMM CPU bottom handset Island loop LOOP2 N A COMM CPU middle handset Island loop LOOP3 N A COMM CPU top handset POS loop DIP Switch Settings Memory Board DIP Switch SC Memory I O S1 On the SC MEMORY I O board top left DIP switch Position amp Definition Setting 1 Boot to monitor after reset open Boot to OS after reset closed 2 Debug mode open Normal closed 3 Don t talk to PC while in monitor open Monitor I O goes to PC also closed 4 Monitor I O goes t2. 3000 Op op op op E9000 Gasboy CFN Series SC III Technician s Guide Site Controller III Ports and Switches 15 SC3 Comm Board DIP Switch CPU S3 SC3 Comm Board DIP Switch S3 position 4 default signon Jumper Settings SC Comm CPU Board settings Jumper Description Setting K3 AC power fail sense 2 3 to enable 1 2 to disable K4 AC watch dog timer 1 2 to enable K5 SC Comm CPU testing only 1 2 to reset K6 RS 485 loop 1 2 3 for 4 wire 1 2 for 2 wire K7 RS 485 loop 2 2 3 for 4 wire 1 2 for 2 wire K8 Rx Clock from synchronous modem 1 2 to connect DB 25 15 K9 ETC output to synchronous modem 1 2 to connect DB 25 24 K10 Tx clock input from synchronous 1 2 to connect modem DB 25 17 KII EPROM type 2 3 for 27128 or 27256 K12 EPROM type 2 3 for 27128 or 27256 default Gasboy CFN Series 16 Site Controller III Ports and Switches SC III Technician s Guide SC Comm Memory I O board settings Jumper Description Setting KI Date Time Clock Speed 1 2 for 4 wait state 2 3 for 1 wait state K2 Enable A19 to RAM 2 3 for 128Kx8 1 2 for 512Kx8 K3 RAM size 2 3 for 128Kx8 1 2 for 512Kx8 K5 Tokheim Reset Output Channel 2 1 2 for reset Do not Install not supported default Gasboy CFN Series
3. 35745 Profit Point Clerk s Manual version 2 1 C35746 Profit Point Reference Manual version 2 1 C09215 Point of Sale and Shift Change version 003 Pump Interface C09146 Pump Interface Manual C01745 Current Loop Interface Unit Manual Card Encoding and Miscellaneous C09136 CEN Series Clubcard Format C01687 CFN Series Card Encoding Manual Remote Communications C09141 PC SiteControl User s Manual Technical Publications C01759 CFN Diagnostic Manual C35922 Technician s Manual SC III Technician s Guide Table of Contents iii Table of Contents OVVIE W ise da E RS da UR duced a epa a 1 Provided Equipment 2 citi ERREUR REI E ERR 1 Optional Equipment depending on setup 0 0 00 0c eee eee eee 2 Cable and Wiring essel bmp REI Pee ba Hee E awe er PES 2 Site Controller Board Installation 3 Screen SAVER 2 uua ud DUCES SIENTEN DE TETTE GUAE UNS 3 Installing the SCII software 4 Printer setup optional esise renis eir Seaia tee ete 5 Netscape Navigator Browser 0 0 0 eee eee eee ene 6 Installationits lt 5 s tac eee CETERIS EE ee i 6 On line Documentation setup 6 New SCIII configuration menus LL 6 Creating the desktop icon for SCHI 0 0 2 ee eee ee eee 7 Creating the Profit Point desktop icon 8 Creating the SC3 Help desktop icon 0 00 cee eee eee 10 Starting the Icon editor provided with OS 2 LL 10 Front panel components 0 0 0 eee cece ete eee
4. Customer display Pin Pad Cash Drawer UPC scanner Cable and Wiring The following drawing illustrates the SCIII cable layout Loop 2 Island 485 Port Loop 1 Island 485 Port Loop 3 POS High Speed 485 Port SC Comm DIP Switch Local RS232 Port 1 enw a Ribbon Cable W amp M Switch T CA Ik to RS232 Port 2 NH 23 OOO RE RE RE CHAR AR ERR GE a R3232 Port 6 Dual Tokheim RS232 Port 3 RS232 Port 5 RS232 Port 4 e Port 1 Local RS232 use cable number C05994 SCIII terminal cable assembly e Port 2 Ribbon Cable to RS232 use ribbon cable number C05554 not currently used e Port 3 RS232 use cable number C05996 two 67 98 box or C07119 single 67 98 box SCIII to Tokheim cable assembly e Port 4 RS232 use cable number C05995 SCIII modem cable assembly e Port 5 RS232 use cable number C06006 SCII Wayne cable assembly e Port 6 is extra and can be used as either a modem or Wayne Note Ports 1 4 5 and 6 are interchangeable Loops 1 2 and 3 use cable number C05670 cable assembly 4 position 1 1 HS Line 8ft phone cable Gasboy CFN Series SC III Technician s Guide SCIII and OS 2 3 Site Controller Board Installation Identify and set all switches Refer to a later chapter in this manual for reference 2 If PC is powered up
5. Gasboy CFN Series Site Controller Ill Technician s Guide Version 3 0 Part Number C35922 Gasboy International Inc a Tokheim subsidiary Gasboy CFN Series Site Controller Ill Technician s Guide Version 3 0 April 10 2000 Gasboy International Inc Lansdale Pennsylvania Gasboy International Inc P O Box 309 Lansdale PA 19446 Copyright 1997 2000 by Gasboy International Inc A subsidiary of Tokheim Corporation Inc All rights reserved Printed in the United States of America The information in this document is confidential and proprietary No further disclosure thereof shall be made without permission from Gasboy International Inc Gasboy International Inc believes that the information in this document is accurate and reliable However we assume no responsibility for its use nor for any infringements of patents or other rights of third parties resulting from its use We reserve the right to make changes at any time without notice REVISION RECORD OF THIS DOCUMENT Part No Date Published SC III Release Levels C35922 May 1997 Version 3 0 C35922 August 28 1997 Version 3 0 C35922 April 10 2000 Version 3 0 Site Controller Ill Related Publications Site Controller IIl version 3 0 Part No Title C35920 SC III Manager s Manual version 3 0 C09226 SC III Configuration Manual version 3 0 C35921 SC III Pocket Reference version 3 0 C09204 Check Point Reference Manual C
6. Icon tab find the Help icon by clicking the Find button In the appearing window type the name of the icon file help ico in the Name box and in the Start folder enter C SC3 When the icon is displayed click OK If the icon is not found you will need to locate the file on the release diskettes Gasboy CFN Series SC III Technician s Guide Icons 11 Place in the SC3 directory and follow these instructions again 6 Click Save and close the windows Starting the Icon editor provided with OS 2 In a OS 2 session at the prompt type iconedit This will start the icon editor program to create or change existing icons Gasboy CFN Series 12 Site Controller III Ports and Switches SC III Technician s Guide Site Controller Ill Ports and Switches For your general information the ports and switches are listed in this manual You can find this same information in Appendix A of the SCIII Manager s Manual Front panel components e Power Switch controls the power to the Site Controller III PC system e PC reset Switch resets the PC but leaves the SC Comm operations running e PC Power Indicator indicates that power is being supplied to the controller e HardDisk Status Indicator lights when the disk is being accessed Serial Parallel Ports The RS232 ports on the SC can be used for any function that needs a RS232 port The ports on the PC are more limited Com1 4 can be used for login log printers and command output
7. ene 11 Serial Parallel Ports eoo beoe b Wee SAS Renee es ES ae Es 11 DIP Switch Settings iii oe e es Peu RECS RR UR ane 12 Memory Board DIP Switch SC Memory I O SIL 12 Memory Board DIP Switch SC Memory I O 52 13 PC IRQ Switch SC COMM CPU Sl 13 PC Address Switch SC COMM CPU 82 sees 13 SC3 Comm Board DIP Switch CPU 83 LL 14 Jumper Settings is hola rile ia eco hg n 14 SC Comm CPU Board settings 14 SC Comm Memory I O board settings 15 Gasboy CFN Series iv Table of Contents SC III Technician s Guide Gasboy CFN Series SC III Technician s Guide SCIII and OS 2 1 SCIII and OS 2 Overview This guide steps through the installation of the Site Controller III boards installing the OS 2 and Site Controller software creating desktop icons and other information necessary to install a Site Controller III Provided Equipment Site Controller III board assembly PC which consists of e keyboard mouse e case PC tower e power cable e diskettes Monitor one of the following e 9 B W monitor part number C09502 e 14 B W monitor part number C09503 e 4 color monitor part number C09504 Monitor cable Manuals Gasboy CFN Series 2 SCIII and OS 2 SC III Technician s Guide Optional Equipment depending on setup Modem cable Modem Parallel printer Serial printer Printer cables Wayne SCIII cable Tokheim cable POS Distribution box with cables
8. g printer assigned to the same port as an OS 2 printer driver When the setup is completed click OK Another screen will give you the option of learning about OS 2 Click Quit to bypass this option or Ok if you want to learn more Screen Saver VGA monitors do not need screen savers but if you want to enable the screen saver that comes with OS 2 use the following steps from the desktop not a window 1 Place the arrow cursor someplace on the screen that doesn t cover an icon 2 Press the right mouse button A small window will open 3 From the options select Properties 4 In Auto Lockup lower left set the delay that you want Gasboy CFN Series SCIII and OS 2 SC III Technician s Guide 5 6 Click on Plus sign upper right on page 3 Enable Screen Saver mode You do not need a password for screen saver mode Close the window by clicking in the left corner Installing the SCIII software The OS 2 operating system is slightly different from a Microsoft Windows display 1 10 11 From the menu bar at the top of the screen select the Command options icon on the rightside From Options select OS 2 window Place SCIII disk number 1 into the A drive At the prompt enter C a install Enter the IRQ number which is either 10 11 12 or 15 The default is 12 The IRQ number must match the SCIII board setting and must not be used by anything else ex ports hard drive mouse etc Ente
9. he installation the window will return to OS 2 Note If the internal Profit Point has problems check if the following exist in the config sys file If they do comment them out from the file by placing REM in front of the line REM device c tcpip bin vdostcp vdd REM device c tcpip bin vdostcp sys REM run c tcpip bin V DOSCTL EXE Printer setup optional 1 Double click on the OS 2 system icon to open 2 Select System Setup from the displayed icons and double click on the icon 3 Inthe System Setup window Select the Install Remove icon In the Install Remove window select the Selective Install icon The System Configuration menu appears 4 Click on the printer icon located in the lower right corner A window will open displaying a list of printers on the left and port options on the right 5 Select LPTI by clicking in the radio button next to the words LPT1 6 Then select your printer from the listed options by clicking once on the words to highlight 7 Click OK to return to the System Configuration menu 8 Inthe System Configuration menu click NEXT until the OS 2 install window opens 9 Inthe OS 2 install window click the Install button A small Source Directory window will appear to select what drive to install the software from The default if you have been installing from a CD is D OS2 image Gasboy CFN Series 6 SCIII and OS 2 SC III Technician s Guide If you were installing from diskettes
10. ling you to hit CTRL ALT DEL to reboot Follow the instructions Remove the floppy from the A drive To continue installing the SCIII software insert the disk labeled number one in the A drive and at the prompt enter C a install You will proceed to the software installation Select the package s to install from the menu that appears They are 1 Site III software 4 Internal Profit Point Gasboy CFN Series SC III Technician s Guide SCIII and OS 2 5 2 Report Package Q Quit 3 HTML on line documentation Select the package by entering the numbers with a space between them as in this example 1234 Do not use a comma or omit the spacebar between the numbers Then press return You will be given the chance to correct or make any changes The installation process takes several diskettes You will notice that you will be prompted to replace some BIN files that don t exist if this is a new installation Type the letter A in uppercase you will not be prompted again Replace the diskettes as requested at the prompt If you should need to stop the installation process press CTRL C You will return to the C prompt You will need to start the install process from the beginning when you return It is not recommended that you stop the installation process When you insert diskette number 3 and press return the window will change to a DOS window to install the Profit Point software When it has completed t
11. o SC port 1 open No monitor I O to SC port 1 closed Gasboy CFN Series 14 Site Controller III Ports and Switches SC III Technician s Guide Memory Board DIP Switch SC Memory I O S2 On the SC MEMORY I O board top right DIP switch Position amp Definition Setting 1 Battery 1 open disabled closed enabled 2 Battery 2 open enabled closed disabled 3 N A unused 4 N A unused PC IRQ Switch SC COMM CPU S1 On the SC COMM CPU board in the bottom middle DIP switch is the IRQ enable DIP switch The IRQ enable switch chooses one of the four possible interrupt priorities Only one may be selected and no other device on the PC can use that interrupt SC3 EXE currently assumes level 15 Other choices are 12 11 and 10 Closed IRQ 15 Default closed 2 Closed IRQ 12 Default open 3 Closed IRQ 11 Default open 4 Closed IRQ 10 Default open PC Address Switch SC COMM CPU S2 On the CPU board bottom right the PC address DIP sets where in the PC address space the Dual RAM will occur The SC Comm board currently assumes D0000 Switch Address Switch Address cl cl cl cl C0000 op cl cl cl D6000 cl cl cl op C3000 op cl cl op D9000 cl cl op cl C6000 op cl op cl DC000 cl cl op op C7000 op cl op op DF000 cl op cl cl CC000 op op cl cl E0000 cl op cl op CF000 op op cl op E3000 cl op op cl D0000 op op op cl E6000 cl op op op D
12. ouse button Click the Create button at the lower left of the screen Another window will automatically open In the Program tab enter the path C SC3 SC3 exe If the path is correct and the icon is in the same directory as the exe file then the program will automatically find the icon and display it on the desktop when the windows are closed If the icon is not found you will need to locate the file on the release diskettes Place in the SC3 directory and follow these instructions again Creating the Profit Point desktop icon This function is automatically done at the installation process if you use the install program If for some reason that you need to create an icon use the following steps 1 Click once on the CFN icon on the desktop using the RIGHT mouse button 2 Click once on the arrow to the right of Create Another using the LEFT mouse button and select New Program 3 At the top of the appearing window enter Profit Point in the Name box 4 Click the Create button at the lower left of the screen few pue Pria Paini 4 Sai a fodder aa ria ip bas bila apin Doer etto E 15 penal S a T Const tto 5 Another window will open In the Program tab a Enter the path C bin menu bat b Set the parameter 1 c Working directory C pos 4 Inthe Session tab a Choose DOS Full Screen then click on the DOS Properties button Select OK for all DOS Settings b Highlight DOS HIGH In the Value box set
13. r the PC address switch The default is 1001 You will be prompted to enter each switch individually pressing the return key after each entry After you have entered all 4 you will be prompted to check your entry If correct press Y If not press N and you will return to enter the switch sequence again Do you want to save the configuration Enter a Y to save the configuration and reboot the site If you enter No N you will not save this configuration information Do you want to add the SCIII software files to your hard disk Enter a Y to add the files that you want installed on the hard disk Enter an N if you do not want to install any SCIII files If you enter No then only the configuration will be saved This is useful when you are updating a site that is currently running and needs only to change the IRQ or the PC Address leaving the rest of the SCIII software intact A warning message will appear about the site shutting down Follow the instructions on the screen The instructions will vary depending on if you selected to save the configuration or if you are saving the SCIII files to your disk Once you configure the site and it reboots you will not have to enter this information again Any subsequent installation will buypass the configuration and go directly to the SC3 software A popup box labeled Install cmd will open asking if you want to close the session without saving your data Click Yes Another popup box will open tel
14. t any other time for configuration changes You will not have to use the R window Gasboy CFN Series 8 Icons SC III Technician s Guide Icons Creating the desktop icon for SCIII This function is automatically done at the installation process if you use the install program If for some reason that you need to create an icon use the following steps 1 Open the OS2 system folder by clicking on the icon using the LEFT mouse button 2 Double click on the Command Prompts icon 3 Click once on the OS 2 window icon using the RIGHT mouse button 4 Click once on the arrow to the right of Create Another using the LEFT mouse button and select New Program o 59 B BG cam ENTERS 3 pels 0138234M b S Mol MS 05 2 System Icon View SEE Folder Edit View Selected Help E i A Open as Minimized WarpCenter System Setup Properties a Window Viewer Help bi IC CENE gt Default Templates Problem Determination Tools riv Move Program copy Create shadow Folder Edit View Selected Help Delete Pickup fang Lock in Place o DOSfromDrive A wIN OS 2 Window WIN OS 2FullScreen DOS Window DOS Full Screen ir SENTIS 05 2 Full Screen ue e Shredder 5 Atthe top of the appearing window enter SC3 in the Name box Gasboy CFN Series SC III Technician s Guide Icons 9 6 From the options listed select Desktop by clicking once on the name with the left m
15. the window will display A 10 Click install to install the printer software for your printer Once installed close any remaining open windows You may have to reboot your PC for the changes to take effect Netscape Navigator Browser Installation Instructions on installation and how to use the browser come with the purchased software Install Netscape according to the instructions given with your purchased copy Once Netscape Navigator is installed open the browser by double clicking on the Netscape icon on the desktop See the Netscape documentation on how to use the browser On line Documentation setup The installation of the SCIII software will automatically install the correct path to the on line documentation The setup described here is for reference only The Index htm is the main page to access all of the documentation It is also known as the Home page through out the documentation At any time when using the documents click on the word Home or Home Page and you will return to this page Index htm to select another document Home page or Home is a term used on the Internet for the base or beginning page To open a document click on the name of the manual you wish to review Finding the Home page 1 Open Netscape Navigator It may complain about not being able to establish a con nection Ignore this error message by clicking OK the browser will open anyway Once you set the startup page to point to a local file as instr
16. to On c Highlight DOS AUTOEXEC In the Value box type C bin OS2exec bat Highlight DPMI DOS API In the Value box select Enabled Gasboy CFN Series 10 Icons SC III Technician s Guide e Highlight DOS DEVICE In the Value box DELETE any text listed f Highlight DOS files In the Value box set the number of sessions that can be opened The default is 20 The setting in the installation program is 50 7 Inthe Icon tab find the PP icon by clicking the Find button In the appearing window type the name of the icon file pp ico in the Name box and in the Start folder enter C SC3 Hans pu ED BwkFbrkc j pam DI por l Search All jubizicari Le cool Heel When the icon is displayed click OK If the icon is not found you will need to locate the file on the release diskettes Place in the SC3 directory and follow these instructions again 8 Click Save and close the windows Creating the SC3 Help desktop icon This function is automatically done at the installation process if you use the install program If for some reason that you need to create an icon use the following steps 1 Click once on the CFN icon on the desktop using the RIGHT mouse button 2 Click once on the arrow to the right of Create Another using the LEFT mouse button and select New Program 3 At the top of the appearing window enter SC3 On line in the Name box 4 Click the Create button at the lower left of the screen 5 Inthe
17. turn off and unplug the PC 3 Remove the PC tower cover The SCIII boards require two full length ISA side by side slots in the PC tower Locate two side by side slots and remove the slot covers if they are still attached 4 Slide the boards gently into the ISA slots of the PC motherboard Make sure that the front of the boards rest on the brackets of the tower and the back bracket aligns with the screw hole 5 Screw the board bracket onto PC and replace cover Turn on the PC booting from the OS 2 install diskette or CD Follow the instructions on the screen If you are installing from diskettes you will be using several to install the OS 2 operating system Under most install circumstances take the default options that appear 8 Choose easy install If you are re installing from a disk crash then you must choose Advanced Installation If you need assistance with the advanced install contact your IBM representative For Advanced Installation only When prompted select these two options 1 Do not format the partition 2 FAT file system for Windows compatibility After several diskettes you will boot from the OS 2 screen Follow the instructions System Configuration Take the defaults listed for the system configuration except for e Primary Display select VGA from the options listed e Do not install TCP IP e Do not install a printer driver unless you have separate OS 2 and log printers Note You cannot have the lo
18. ucted below this will go away 2 From the Menu bar at the top of the page select File Open file A window will open Find your on line documentation folder on the C drive This should be located in the path C SC3 HTML When you locate your on line folder open it and select the file called Index htm 3 When the path is displayed in the File name box press OK 4 The program will display the document Index htm This is the beginning of the on line documentation Set up Netscape Navigator to open this page every time you start the browser 1 From the Menu bar select Options General Preferences 2 Fromthe Appearance selection middle of the page Enter the path to Index htm in the box Browser Starts With It will be C SC3 HTML index htm or similar 3 Click OK Now the browser will display Index htm as the start page every time you open the browser 4 To Quit from the Menu bar select File Exit Gasboy CFN Series SC III Technician s Guide SCIII and OS 2 Once the browser is set to open the Index htm on the local disk C it will no longer produce an error message on startup New SCIII configuration menus As of this writing the Graphical User Interface will not be shipping with release 3 0x As currently set up only 90 of the site information could be entered and that was only at startup The complete interface will ship with a later release and will allow 100 of the SCIII to be configured at setup and a
Download Pdf Manuals
Related Search