WWA-02AA Wireless Water & Freeze Alarm, Installation Instructions
Contents
1. of 2 seconds Battery Low Battery The WWA 02AA will send an alert on the Z Wave network at regular intervals when it detects a low battery condition In addition it will periodically blink the LED After a water leak please ensure that there is no moisture in the unit and around the battery Batteries are NOT covered under manufacturer warranty Please follow the guidelines to maximize your unit s battery life Program the unit into your home automation network according to instructions provided by your specific controller gateway Note Every z wave controller has its own default wake up cycle that it will automatically apply to the WWA 01 once installed into your network typically 4 hours FortrezZ recommends wake up cycle time to be increased to no less than 12 hours Remember that this wake up notification cycle time does not affect the units measurement settings for water leak detection If a water leak is detected by the WWA 01 it will send an alarm notification within seconds to the controller gateway In your controller interface manually set the wake up interval in your device s settings to 12 hours or more according to your preference You may need to consult your controller gateway manufacturer with questions you may have PLEASE DO NOT continually test the WWA 02 In alarm mode the WWA 02 turns ON the LED and communicates with the Z wave network using up a large amount of battery life A new batte2. WWA 02AA Wireless Water amp Freeze Alarm Installation Instructions sPeans Oav Products that speak Z Wave work together better A Initial Installation WWA 02AA Wireless Water amp Freeze Alarm Sensor includes 2 x AA batteries Remove isolator from battery terminal You will see the LED turning ON on the front side of the sensor Note If you do not see the LED turning ON please consult your user manual for trouble shooting your sensor Use the provided hardware 4 screws to screw the cover on After screwing the parts together the use of some sealant such as silicone caulk around the screws is recommended Choosing a mounting location The WWA 02AA is suitable for use in dry interior locations only Common applications include Jacuzzi tub under sinks sump pump refrigerator water heater toilets and washing machines Avoid placing the unit close to a metal frame or other metal enclosures that may affect RF range Do not place your sensor in an overly humid space This may trip false alarms Place the unit so that any leaks that may occur will not drip directly on the unit but puddle into the water sensor pads Testing the WWA 02AA Moisten a paper towel and place over both of the sensor metal pads on the water sensor until you observe two quick LED blinks If you do see the LED blink remove the moistened paper towel and clean the small metal pads of any water residue Reset alarm by holding the program switch for a minimum
3. fication The WWA 02AA will wakeup and send a notification every 4 hours default to a controller to query and update the status of the unit A controller can change this wakeup interval Battery life is decreased when the wakeup interval time is shorter Status LED Indications Numberof Blinks Meaning O 1 Wakeup Notification Sent after quick button press while in Network Water Alarm Temperature Alarm either high or low setpoint triggered WAKEUPS Wakeup1 Power saving design wakes up every 4 seconds to test water and freeze sensor Wakeup2 Once every 4 approx hours default unit wakes up to send a notification either to a wakeup node or broadcast Complete User Manual www fortrezz com _ 1080 Centre Rd Suite C Phone 248 481 7092 N L Auburn Hills MI 48326 sales fortrezz com FORTREZ www fortrezz com Made in USA 060212
4. ry is recommended to be installed after any actual alarm situation to ensure the unit has adequate power to continue to communicate in the z wave network Using the WWA 02AA in a Z Wave Network Program Switch for Inclusion or Exclusion Ses The switch is used for including or excluding the WWA 01AA in a Z Wave network thes Refer to your controller s User Manual for specific details on network inclusion exclusion and association Water amp Temperature Sensor Inclusion in adding to a network 1 Set the controller to Inclusion mode 2 Briefly press the program button once and the controller will indicate the unit has been included in the network The LED will blink when the inclusion completes Configuring the WWA 02AA The high and low temperature set points in the WWA 02AA can be configured The temperature set points can be configured via a smart controller after inclusion details are provided in the technical appendix Refer to your controller gateway s instruction manual Exclusion from removing from a network 1 Set up the exclusion mode at the controller 2 Press and hold the button for approx 2 seconds until the controller indicates the unit has been removed from the network The LED will blink when the exclusion completes Associations Once in a network a controller can be used to associate the WWA 02AA with other devices in the Z Wave network such as a light or another remote audible alarm Wakeup Noti
Download Pdf Manuals
Related Search