X-17s Users Manual
Contents
1. 4 Click Commit Settings Once clicked the X 600M begins to monitor the newly added device 9 9 xseup x Um C D 192 168 1 2 setup html 2 eoo M Welcome Administrator CONTROLBYWEB c Commit Changes Denon Changes Logout LEN E Devices Find Devices Network List of automatically detected new devices E Devices New Devices Found Rescan Back Show 10 entries Serial Comm Model Address Description Name Select EH Edit Dashboards Number Type X 128 8 Relay Slave 00000057 SERIAL AUTO GENERATE AUTO GENERATE AUTO GENERATE Add X 13S K Thermocouple Type K Slave 0000000d SERIAL AUTO GENERATE AUTO GENERATE AUTO GENERATE Add H View Dashboards X 300 X 300 Temperature Monitor Mode 00 0c c8 02 5c 09 ETHERNET 192 168 1 70 AUTO GENERATE AUTO GENERATE Add X WR 1R12 11 WebRelay 00 0c c8 02 7f 46 ETHERNET 192 168 190 AUTO GENERATE AUTO GENERATE Add Status Ready For product support go to www ControlByWeb com Xytronix Research amp Design Inc Xytronix Research amp Design Inc Page 15 Configuration and Setup X 17s Users Manual 5 On the main menu click the View Dashboards menu tab The View Dashboards page shows a display similar to what users will see when accessing the X 600M s control page The status for each of the relays and inputs inputs should be shown Use this page to test and debug the dashboards panels widgets and components in real time A pull down menu allows acce2. are wired directly to the internal relays with no internal fuse or other over current protection The relays are isolated from all other circuits inside When a relay coil is energized the contacts are closed The load device that is connected to the relay contacts will be on when the coil is energized Digital Inputs The X 17s has four optically isolated digital inputs The inputs are connected with a common return negative connection for the four inputs The optically isolated inputs provide 3KV electrical isolation between the digital inputs and the low voltage control circuits of the X 600M Expansion Bus The expansion bus allows for a family of expansion modules to be connected directly to the X 600M without the need for an Ethernet switch The cable can be a daisy chain with multiple connectors The ribbon cable expansion bus provides both power and communications connections Power Supply The expansion bus can provide up to 1 7 Amps for powering up to 32 expansion modules however the maximum number of expansion modules depends on the module type and power source attached to the X 600M The X 17s employs modern switch mode power supply With this type of power supply the current draw decreases as the voltage increases therefore you can add more expansion modules by using a 24 volt power supply than you can with a 12 volt power supply See the X 600M User Manual for more details Indicators The green Power LED indicator is il
3. 2 Positive side of optically isolated input 2 3 Input 3 Positive side of optically isolated input 3 4 Input 4 Positive side of optically isolated input 4 Com Input COM Negative side of optically isolated inputs 1 thru 4 Com Input COM Negative side of optically isolated inputs 1 thru 4 Page 8 Xytronix Research amp Design Inc X 17s Users Manual Installation and Connections 2 4 Optically Isolated Input Connections Internally each input is connected thru a current limiting resistor directly to an opto isolator No external resistor is necessary as long as the input signal is within the proper range With the X 600M the optically isolated inputs can be used to control relays and remote relays over the network or simply to monitor the state of a discrete device To use these inputs connect a DC control voltage directly to the input and set up the input function using the configuration pages 2 4 4 DC Inputs With DC inputs no external components are required as long as the maximum input voltage is not exceeded See Specifications A DC voltage can be reduced with an external resistor of the appropriate value and power rating to reduce the input current See Section 3 2 2 4 2 AC Inputs If an AC signal voltage needs to be detected use a signal conditioner to convert the AC signal to a DC voltage within the input range An AC signal conditioner can be made using a diode or bridge rectifie
4. EH Edit Dashboards imber ype X 128 8 Relay Slave 00000057 SERIAL AUTO GENERATE AUTO GENERATE AUTO GENERATE Add X 138 K Thermocouple Type K Slave 00000004 SERIAL AUTO_GENERATE AUTO GENERATE AUTO GENERATE Add E View Dashboards X 17S 4 Input 4 Relay Slave 0000072 SERIAL AUTO GENERATE AUTO GENERATE AUTO GENERATE C Add X 300 X 300 Temperature Monitor Mode 00 0 68 02 5c09 ETHERNET 192 168 1 0 AUTO GENERATE AUTO GENERATE Add X WR 1R12 11 WebRelay 00 0c c8 02 7f 46 ETHERNET 192 168 1 90 AUTO GENERATE AUTO GENERATE Add Status Ready For product support go to www ControlByWeb com Xytronix Research amp Design Inc Page 14 Xytronix Research amp Design Inc X 17s Users Manual Configuration and Setupl 3 In the Select column click the checkboxes of the I O components you would like to configure and select the Create Device Widget checkbox This will display the status of the I O on the Dashboard Click Add Checked I O to submit these changes ES Setup x QC 1192 168 122 setup html 192 168 1 103 popup php EE 2X600M 4 Input 4 Relay Slave Add VO Welcome Administrator Amit Chany Abandon Char Le it CONTROL SY ee Add I O found on 4 Input 4 Relay Slave 00000072 Please see below the list for a description of each field oes Ss ae MIC i Network Veto vo Type VO Description VO Name Digital Input 1 AUTO GENERATE AUTO GENERATE Digital Input 2 AUTO GENERATE AUTO GENERATE Now D
5. digital signals are bridged to a remote location on the network A control voltage applied to the X 17s input module controls relay contacts of a WebRelay Quad or any other ControlByWeb devices at a remote location In this example three switches are connected to an X 17s and a remote WebRelay Quad controls three indicator lights The switches and indicator lights can be in separate buildings With this setup the high low liquid level of a tank could be monitored at a remote location X 17s X 600M WebRelay Quad Lights 1 3 Vswt Input 1 Switches This type of setup allows for switches to be placed far away from the devices they control and sensors to sound alarms at distant locations Note For dry contact switches a voltage source must be provided this could be via the power supply for the X 600M Page 12 Xytronix Research amp Design Inc X 17s Users Manual Example Applicationsl 3 5 Control a device over an IP network The illustration below shows a simple example of using the X 17s to control a device over an IP network The device to be controlled is wired in series with the relay contacts Note A fuse or circuit breaker is shown to limit current overload X 17s X 600M Device to be Controlled Power Supply Powers X 600M amp X 17s Power Source Fuse or Circuit Breaker Computer PLC or Controller 3 6 High Current Relay The illustration
6. the de bounce settings Note If the count mode is set to rise and fall the resulting frequency measurement will be the number of rise and fall edges that have occurred in 1 second De bounce Time The high time count and frequency functions employ a de bounce timer for each input The internal processor periodically polls the input state If the appropriate edge rise fall or both is detected a timer is initialized to the respective de bounce value If the input state subsequently changes a glitch the timer is restarted When the input stabilizes the debounce timer eventually expires and the appropriate high time or event counter is advanced Xytronix Research amp Design Inc Page 5 Installation and Connections X 17s Users Manual Section 2 Installation and Connections Installation consists of mounting the X 17s and connecting it to an X 600M controller with a 10 conductor ribbon cable Programming and testing is done by using a web browser to configure the web pages inputs and outputs for your specific needs 2 1 Installation Guidelines e This unit must be installed by qualified personnel This unit must not be installed in unprotected outdoor locations e This unit must not be used for medical life saving purposes or for any purpose where its failure could cause serious injury or the loss of life This unit must not be used in any way where its function or failure could cause significant loss or pr
7. 2 lt 17s CONTROLBYWEB x r 4 Relay 4 Input Expansion Module i i USERS MANUAL Revision 1 0 4 Relay 4 Input For models X 17s 4 Relays and 4 Digital Inputs e Removable Connector gt Indicator Lights gt Button Switch Inputs co gt Alarms gt Interface with a PLC a division of Xytronix Research amp Design Inc located in Nibley Utah USA Machine Status 2015 Xytronix Research and Design Inc TM www ControlByWeb com X 17s Users Manual X 17s User Manual Revisions Revision Description 1 0 Initial release Page 2 Xytronix Research amp Design Inc X 17s Users Manual Introductionl Section 1 Introduction The X 17s expansion module is used in conjunction with the X 600M controller The X 17s is a multi function module with four relays and four optically isolated digital inputs One or more X 17s expansion modules can be connected to a X 600M control module with a ribbon cable which provides both power and communications The four relays have Form A contacts SPST and can be used to control moderate loads such as solenoid valves alarms and indicator lights The isolated inputs are suitable for use in industrial environments and allow the grounding system of the monitored equipment and the low voltage circuits of the X 17s to be electrically separate Internally the X 17s has a co processor which provides e
8. 24 mA 12 VDC 14 mA 165 mA 24 VDC 8 mA 86 mA Digital Inputs Number of Inputs 4 Minimum Pulse Time high or low 2 5mS Input Current lin 950uA 4V 8 5mA 26V Isolation Viso 3 000 Vrms Reverse voltage Vr 6V max Vin 26V max Vin Hi AV min Vin Lo 3V max Digital Input Measurement Functions Asynchronous status of the digital inputs Pulse width 4 194 304 seconds max Accumulated time an input is asserted 4 194 304 seconds max Total number of transitions 32 bit 1 Hz min 200 Hz max Rising Falling or Both 0 9mS min 63 sec max 4 General purpose SPST 1 form A Silver nickel 125VAC 30VDC 2 5A 100K cycles typical rated load Over voltage Category II Pollution Degree 2 On Off or Pulsed 100ms to 86400 Seconds 1 day Xytronix Research amp Design Inc Page 17 Appendix A Specifications X 17s Users Manual Connector Type Connection wire Stripping Length Connection capacity Conductor minimum Conductor maximum Conductor Type Tightening torque 14 position removable 3 81 mm pitch Use wire rated for 75 C min for connections to the terminal blocks 7mm 1 5mm stranded 1 5mm solid 30AWG UL CUL 14 AWG UL CUL Copper 0 22 Nm min 0 25 Nm max Replacement part number Phoenix Contact 1803691 Expansion Connector Connector Communications LED Indicators Green Yellow Environmental Rating Altitude Operating Temperat
9. ansion bus and the local network for ControlByWeb devices and expansion modules 9 9 ssop e Q 192 168 1 2 setup html X6ooM Welcome Administrator CONTROLBYWEB Commit Changes Abandon Changes Logout Zm E Devices Add edit and delete devices that are attached to the X 600M either through the expansion bus or through the Ethemet network Devices must be added before setting up any I O Logic or Dashboards E Devices Note The Find New Device button resets all the devices attached to the expansion bus This will tur off any relays and outputs on these devices Zo ps 5 Device List New Devices Control Logic emos c Find gt 5 Ada New Device Name Description Address Port Model Serial Number Status Ge devicet X 600M master unit nla X 600M 00 0 c8 00 00 71 lt 1ms devices 8 Input Slave 2 nla X458 00000025 25ms Identify Edit Delete EH view Dashboards Showing 1 2 of 2 Devices Status Ready For product support go to www ControlByWeb com Xytronix Research amp Design Inc 2 In this example we are going to add an X 17s 8 expansion module Click the Add button for the X 17s 9 Oe zx s0tup gt QC 192 168 1 2 setup html gt lt 600m CONTROLBYWEB Welcome Administrator Commit Changes Abandon Changes Logout E Devices Find Devices Devices gt Pall z New Devices Found Rescan Back 5 l Logic F Show 10 entries E Logging Model obo CM Address Description Name Select
10. below shows an example of how the X 17s is used to control an AC motor A high current relay is used to switch the load current to the motor In this example a MOV Metal Oxide Varistor is used to help protect the relay contacts of the X 17s from arc damage Under normal conditions the resistance of the MOV is very high When a spike or surge occurs the resistance of the MOV drops and shunts the high voltage transients v mU Relay 1B Relay 1A Power Supply For X 600M MOV Transient Suppressor E High Current Relay AC Power Source Xytronix Research amp Design Inc Page 13 Configuration and Setup X 17s Users Manual Section 4 Configuration and Setup 4 1 Setup Example The Quick Start Demo After making the power and Ethernet connections the X 600M can automatically scan for the presence of any ControlByWeb Ethernet devices on the same sub net and also for any expansion modules connected to the X 600M via the ribbon cable connector It also automatically creates a dashboard web page and populates it with all of the resources components supported by the Ethernet devices and expansion modules This makes it easy to start experimenting with the web page s user interface and to try out the relays and sensors To quickly add a device do the following 1 Click on the Devices menu tab to pull up the Devices Overview page Then click on the Find New Devices button to scan the exp
11. e to be defective This warranty is extended to the original purchaser of the equipment only For warranty service or repair the product must be properly packaged and returned to Xytronix Research amp Design Inc The purchaser shall prepay all charges for shipping to Xytronix Research amp Design Inc and Xytronix Research amp Design Inc will pay the shipping charges to return the product to the purchaser as long as the product is shipped within the United States If the product is shipped outside of the United States the purchaser shall pay all shipping charges duties and taxes Limitation The foregoing warranty shall not apply to defects or damage resulting from improper use or misuse unauthorized repair tampering modification improper connection or operation outside the electrical environmental specifications for the product Further the warranty does not cover Acts of God such as fire flood hurricanes and tornadoes This warranty does not cover damage to property equipment direct indirect consequential or incidental damage including damage for loss of business profit business interruption loss of data and the like arising out of the use or misuse of this product UNDER NO CIRCUMSTANCES WILL THE LIABILITY OF XYTRONIX RESEARCH amp DESIGN INC TO THE PURCHASER OR ANY OTHER PARTY EXCEED THE ORIGINAL PURCHASE PRICE OF THE PRODUCT REGARDLESS OF THE FORM OF THE CLAIM No other warranty is expressed or implied Xytro
12. he equipment and receiver Connect the equipment into a relay on a circuit different from where the receiver is connected Consult the dealer or an experienced radio TV technician for help Notice Changes or modification not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Xytronix Research amp Design Inc Page 21 Appendix E Mechanical Dimensions X 17s Users Manual Appendix E Mechanical Dimensions dU an www ControlByWeb com 324 000 IU E 097 c D oo o S amp Fo cO e eo e M36 35mm DIN RAIL 000 481 2 981 3 879 000 703 1 406 V USE 48 PAN HFAD SCR EWS Page 22 Xytronix Research amp Design Inc
13. luminated whenever the module is powered To identify the module during installation the X 600M can send a blink command which will cause the power LED to blink for three seconds Eight yellow LEDs indicate the status of the relays and digital inputs and are illuminated when the respective relay coils are energized or a voltage is applied to the respective opto coupler 1 2 Part Numbers and Accessories Accessory Description Part Number X 17s Expansion module with 4 digital inputs and 4 relays X 17s 120VAC relays 4 26VDC inputs Spare Connector 14 position screw terminal connector X 1803691 Page 4 Xytronix Research amp Design Inc X 17s Users Manual Introductionl 1 3 Measurement Functions The internal co processor monitors the digital inputs and provides enhanced features including pulse counting pulse duration accumulated pulse time and frequency measurements All four inputs have separate measurements The following measurements are made Input State This register is the current asynchronously sampled status of the digital inputs High Time These registers measure the pulse width of the most recent pulse These are 32 bit values with a resolution of 0 977mS 1 1024 x 2 4 194 304 seconds max The registers are reset with a rising edge are updated while the input is asserted and remain unchanged until the next rising edge The counters are qualified by the respective de bounce ti
14. mer settings ON Time These registers measure the accumulated total time the respective inputs are asserted If the input is configured for rising edge pulses the counters advance when the opto couplers are ON If the input is configured for falling edge pulses the counters advance when the opto couplers are OFF The On Time counters do nothing when the edge is set to both rise and fall These counters are 32 bit values with a resolution of 0 977 mS 1 1024 x 2 4 194 304 seconds max The input state for the On Time counters is polled at a 1024Hz rate and are not qualified by the respective de bounce timer settings This measurement could be used to measure the total operating time of a pump or machine The measurement would indicate the total hours the pump or machine has operated since the On Time register was reset Count These registers measure the total number of pulse transitions rise fall or both that have occurred on the respective inputs The counters are qualified by the respective de bounce timer settings The counters are 32 bit which allows operation with paddle wheel flow meters and other devices which output a large number of pulses Frequency These registers measure the total number of pulses that have occurred over a 1 00 second interval The measurement is updated precisely once per second Since the event counters are qualified by the respective de bounce timer settings the frequency measurements are also qualified by
15. nhanced features including pulse counting pulse duration accumulated pulse time and frequency measurements All 4 inputs have separate measurements Programmable de bounce timers allow glitches and short pulses to be filtered out The X 600M is a multifunction web enabled industrial I O controller It performs control logic and monitoring functions similar to that of a Programmable Logic Controller PLC However unlike a PLC the X 600M is designed for web based applications from the ground up No add on software or hardware is required The X 600M can be fully configured programmed and tested using its built in web server The web setup pages are intuitive and easy to use and do not require special programming skills The X 600M together with the X 17s provides an easy flexible and reliable way to monitor sensors and control devices over a network The X 17s is suitable for use with security systems freezer doors light switches and water meters as well as with moderate loads such as solenoid valves alarms and indicator lights X lt 17s CONTROLBRYWER ex n 1 Y T 4 Relay 4 Input Xytronix Research amp Design Inc Page 3 Introduction X 17s Users Manual 1 4 Connectors amp Indicators Relays The X 17s has four relays Terminals are provided for the Common and Normally Open contacts of each relay A plug in screw terminal makes it easy to make the wiring connections The connector terminals
16. nix Research amp Design Inc specifically disclaims the implied warranties or merchantability and fitness for a particular purpose Some jurisdictions may not allow the exclusion of limitation of liability for consequential or incidental damage Page 20 Xytronix Research amp Design Inc X 17s Users Manual Appendix D FCC Statement Appendix D FCC Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions This device may not cause harmful interference This device must accept any interference received including interference that may cause undesired operation Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause interference to radio communications There is no guarantee however that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between t
17. ns electronic or mechanical including photocopying or scanning for any purpose other than the personal use by the purchaser of this product Xytronix Research amp Design Inc assumes no responsibility for any errors that may appear in this document Whereas reasonable effort has been made to make the information in this document as useful and accurate as possible Xytronix Research amp Design Inc assumes no responsibility for the application usefulness or completeness of the information contained herein Under no circumstance will Xytronix Research amp Design Inc be responsible or liable for any damages or losses including direct indirect special incidental or consequential damages or losses arising from either the use of any information contained within this manual or the use of any products or services referenced in this manual Xytronix Research amp Design Inc reserves the right to change any product s features specifications documentation warranties fee schedules and conditions at any time and without notice Xytronix Research amp Design Inc Page 19 Appendix C Warranty X 17s Users Manual Appendix C Warranty This Xytronix Research amp Design Inc product has a warranty against defects in material and workmanship for a period of one year from the date of shipment During the warranty period Xytronix Research amp Design Inc will at its option either repair or replace products that prov
18. operty damage 2 2 Mounting X 17s can be mounted to a standard 35mm by 7 55mm DIN Rail Normally expansion modules are mounted to the left side embossed logo side of the enclosure of the X 600M controller so that the ribbon cable doesn t cover the power connector The X 17s should be located in a clean dry location where it is protected from the elements Ventilation is recommend for installations where high ambient air temperatures are expected to be high See Appendix D Mechanical Information for additional mechanical details 2 2 1 DIN Rail Mounting Attach the X 17s to the DIN Rail by hooking the top hook on the back of the enclosure to the DIN Rail and then snap the bottom hook into place To remove the X 17s from the DIN Rail use a flat head screwdriver Insert the screw driver into the notch in the release tab and pry against the enclosure to release the bottom hook Page 6 Xytronix Research amp Design Inc X 17s Users Manual Installation and Connections 2 3 Making Connections CAUTION Make sure the power is shut off before making connections CAUTION This unit should be installed by a qualified technician CAUTION Miswiring or misconfiguration could cause permanent damage to the X 17s the equipment to which it is connected or both A removable terminal connector is provided for making the power connections The correct wiring procedure is as follows 1 Make sure power is turned off 2 Rem
19. ove the terminal connector from the X 17s and make wiring connections to the terminals This technique avoids stressing the internal components while torquing the screws 3 Reconnect the terminal connector 4 Apply power It is recommended that any load device to be controlled not be connected to the expansion modules until after the X 600M has been configured and tested By doing this wiring and configuration mistakes will not cause the load device to turn on unexpectedly Make certain the wires are properly inserted into to the terminals and that the screws are tight Wire Specification Use wire rated for 75 C min for connections to the terminal blocks Connector Specifications Type 14 position removable 3 81 mm pitch Connection wire Use wire rated for 75 C min for connections to the terminal blocks Stripping Length 7mm Connection capacity 1 5mm stranded 1 5mm solid Conductor minimum 30AWG UL CUL Conductor maximum 14 AWG UL CUL Conductor Type Copper Tightening torque 0 22 Nm min 0 25 Nm max Xytronix Research amp Design Inc Page 7 Installation and Connections X 17s Users Manual 14 Pin Wiring Connections Terminal Description 1A Relay 1 NO 1B Relay 1 COM 2A Relay 2 NO 2B Relay 2 COM 3A Relay 3 NO 3B Relay 3 COM 4A Relay 4 NO 4B Relay 4 COM 1 Input 1 Positive side of optically isolated input 1 2 Input
20. oviess _Dital input AUTO GENERATE AUTO GENERATE f Digital input 4 AUTO GENERATE AUTO GENERATE E Show 10 Relay1 AUTO GENERATE AUTO GENERATE Model Relay 2 AUTO GENERATE AUTO GENERATE E Select Relay3 AUTO GENERATE AUTO GENERATE E X 128 8 Reli TO GENERATE Add Rely4 AUTO GENERATE AUTO GENERATE X 13S K Th Input High Time 1 AUTO_GENERATE AUTO_GENERATE fo SENERATE Add X 3000 300 Input High Time 2 AUTO GENERATE AUTO GENERATE fO GENERATE Add XWRRig Input High Time 3 AUTO GENERATE AUTO GENERATE a Basan Add Input High Time 4 AUTO GENERATE AUTO GENERATE E Input On Time 1 AUTO GENERATE AUTO GENERATE aq pisos N y Input On Time 2 AUTO GENERATE AUTO GENERATE o Input On Time 3 AUTO GENERATE AUTO GENERATE 8 Input On Time 4 AUTO GENERATE AUTO GENERATE Frequency Input 4 AUTO GENERATE AUTO GENERATE Frequency Input 2 AUTO GENERATE AUTO GENERATE o Frequency Input 3 AUTO GENERATE AUTO GENERATE Frequency Input 4 AUTO GENERATE AUTO GENERATE Counter 1 AUTO GENERATE AUTO GENERATE 3 Counter 2 AUTO GENERATE AUTO GENERATE o Counter 3 AUTO GENERATE AUTO GENERATE a Counter 4 AUTO GENERATE AUTO GENERATE Showing 1 to 24 of 24 entries Select All Deselect All Add Checked 1 0 Create device widget on panelt WO List This shows the type and reference number of each input and output on the device Status Ready Status Ready For product support go to www ControlByWeb com Xytronix Research amp Design Inc
21. r and a capacitor Prepackaged signal converters are available as accessories at industrial automation distributors A simple voltage converter module manufactured by www redlion net is shown below These are available in two input voltage ranges that cover the spectrum from 4 270VAC DC These devices have a MOSFET output solid state DC contact closure which is compatible with the X 17s input The converter module accepts AC 50 60 Hz or DC voltages at input cycles up to 30 Hz The converter provides isolation between the input and output using an opto isolator You must provide a voltage source for the input of the X 17s as shown in the example below 12 24V Xytronix Research amp Design Inc Page 9 Example Applications X 17s Users Manual Section 3 Example Applications 3 1 Monitor a gate position over an IP network The illustration below shows an example of using the X 17s to monitor the status of a gate or door over an IP network The status of the device is detected with a switch These type of sensors are called dry contacts in that the device output is a bare switch with no power source A voltage source for the dry contact switch must be provided this could be via the power supply for the X 600M X 17s X 600M Input 1 T 11 28VDC Power Supply Voltage y O Dry Contact 3 2 Monitor a sensor with a high voltage output To monitor a DC voltage that is greater than the input rating of the X 17
22. s a series resistor can be used to reduce the input current X 17s X 600M Input 1 36VDC signal voltage di 1 2K resistor Dry Contact e The formula to calculate external resistor values is provided below The X 17s draws 8mA at 26V R V 26 0 008 Where V Desired Vin R External resistor value required The external resistor must also be rated with a minimum power value minWatts V 26 x0 008 Page 10 Xytronix Research amp Design Inc X 17s Users Manual Example Applicationsl For example to connect a 36VDC signal voltage to the X 17s R 36 26 0 008 1250 Ohm resistor The resistor must be at least 36 26 x 0 008 0 08 Watts A 1200 Ohm 1 4watt resistor would be suitable 3 3 Monitor the digital outputs of a PLC The illustration below shows a simple example connecting the digital outputs from a PLC to an X 17s Input Module In this example the voltage for the inputs is provided by the PLC so no other excitation voltage is needed X 17s X 600M Programmable Logic Controller PLC nEEHEHD n BEBEHD Digital Outputs from PLC Computer PLC or Controller Xytronix Research amp Design Inc Page 11 Example Applications X 17s Users Manual 3 4 Bridge switches to a remote location The illustration below shows an example where
23. ss to other dashboards Within minutes you can experience the power and flexibility of the dashboard s user interface and experiment test the buttons sliders and data entry boxes to meet your needs for your specific application eoe Setup x A 192 168 1 2 setup html Wiz x lt 6E600 M Welcome Administrator CONTROLBYWEB Commit Changes Abandon Changes Logout amp System X600M Dashboard 1 3 Network E Devices 4 Input 4 Relay Slave 0000007a gt vO rely ANN on on v NN noon Relays MEN os on EH Edit Dashboards c E digta neu 1 TT Digital Input 2 i Digital Input 3 er 1j Digital Input 4 pr Status Ready For product support go to www ControlByWeb com Xytronix Research amp Design Inc Page 16 Xytronix Research amp Design Inc X 17s Users Manual Appendix A Specifications Appendix A Specifications Power Requirements Input State High Time On Time Count Frequency Edge Trigger De bounce Time Relay Contacts Number of relays Load Type Contact Form Contact Material Max Voltage Max Current Electrical Life Environmental Rating Control Options Pulse Timer Duration Input Voltage 9 28 VDC power is supplied via the expansion bus cable 24V recommended Current See table below for typical values at 25 C Power Supply Opto couplers amp Relays OFF Opto couplers amp Relays ON 9 VDC 18 mA 2
24. ure Storage Temperature Humidity Mechanical Size Weight Ribbon cable 2x5 position polarized 0 100 pitch RS 485 Power On Input 1 thru 4 Relay 1 thru 4 Indoor use or NEMA 4 protected location up to 2000m 40 C to 65 5 C 40 F to 150 F 40 C to 85 C 40 F to 185 F 5 95 non condensing 1 41 x 3 88 x 3 1 in 35 7 x 98 5 x 78 mm not including connector 4 8 oz 136 g Electromagnetic Compliance IEC CISPR 22 CISPR 24 FCC 47CFR15 Class B EN55024 ITE Immunity 2010 EN55022 Emissions 2010 Product Safety Compliance UL 61010 1 CE Page 18 Xytronix Research amp Design Inc X 17s Users Manual Appendix B Trademark and Copyright Information Appendix B Trademark and Copyright Information This document is Copyright 2015 by Xytronix Research amp Design Inc All rights reserved X 600M WebRelay ControlByWeb and Xytronix Research amp Design are trademarks of Xytronix Research amp Design Inc 2005 2015 All other trademarks are the property of their respective owners All parts of this product and design including but not limited to firmware hardware design schematics PCB layout concept graphics users manual etc are property of Xytronix Research amp Design Inc 2005 2015 X 600M may not be opened disassembled copied or reverse engineered No part of this manual may be reproduced or transmitted in any form or by any mea
Download Pdf Manuals
Related Search