User`s Manual - Parts Express
Contents
1. RS485 422 VIDEO AB VIDEO IN RR T T OUT CCTV Tester User s Manual 2 4 Specification Model CT330 S CCTV Tester Signal Mode NTSC PAL automatically suitable Display inch LCD screen 960 x 240 resolution 3 0 Video Test Video Input 1 channel BNC Video Output 1 channel BNC Adjustable Brightness adjustable Communication RS232 RS422 simplex and RS485 Voltage DC12V Video analyzing Video signal attenuation analyzing 1 0SDMenu EngshOSDmeu a Rechargeable 6 hours recharging time Dimension 654x358x180 166mm x 91mm x 48mm PTZ Control and Test CCTV Tester User s Manual 3 Operation Introduction 3 1 Power and battery A G H The power slide switch is located at the side of the tester Turn the power slide switch on to power on the tester turn it off to power off the tester After the tester turning to sleeping mode turn the slide switch on again to restart it This tester has panel battery inside the device more capacity longer working time Without the authorization from the manufacturer please don t release the rear panel and try to repair the battery The batteries should be plugged in over 5 hours for full charge while charged the Charge Indicating LED will be on after full charging the Charge Indicating LED light will turn off and the charging stop automatically The charged batteries can operate for 10 hours or more When the battery indicator in system inform2. 90 gt Battery power status 100 90 75 50 25 5 B Press Set button to start the set up C Press num button 2 and 8 PTZ direction button UP and DOWN to select the option Battery power status can be edited D Press num button 2 6 8 PTZ direction button UP DOWN RIGHT to adjust the parameter Press num button 4 PTZ direction button LEFT to save and quit F Press num button 4 again to finish the setup situation the characters in the menu will stop glitter G Press MENU button for 1 second to back to the main menu Note In our device PTZ there are 16 some protocol ok has 7 levels for the PTZ 0 means the minimum speed 17 or 7 means the maximum speed 3 5 PTZ test A Connection Connect the tester with the PTZ camera as the picture Shows In the main menu press num button 2 to switch to the PTZ testing function CCTV Tester User s Manual submenu as the following PTZID lt ADDRESS 001 VIDEONULL gt Video format 001 255 PAL NTSC NULL Operation Press the ADR button input the PTZ address by using num button Press the SET button to save the setup Press the MENU button to hide the menu information and show a clean screen for camera image Press MENU button for 1 second to back to the main menu PTZ controlling When connect to the PTZ correctly the camera image will be displayed on the screen of the tester after setup the proper pr
3. CCTV Tester User s Manual CCTV Tester User s Manual Table of Contents Sa NOTAR 2 1 1 Precaution before using the tester srrrrrnrsrrrorrrrrrrrrrrnrrrnrrrrnrrrvvrrnnrrrnrrnssrrnnrressssnnne 2 1 2 Precautions when using the tester rsrrrrrsrrrrsrrrrronrrrrrnvrrrrrnnrrrrrnvrrrrnnrrrrnnnvrnnnnnnnn 2 1 3 Precautions for battery charging and using 2220000220000eseeneeeenenennnnn 2 IHTTOQUELION u ae une 2 2 1 Features and TUNCUON seen 2 2 2 Standard EMS saadan dekade 3 23 UNG UO Ol CAC Pal anea a 4 22 SDSCINIC AION hp 6 Operation INTFOGUCTION 2 000 ccc ccseccensecesseecessecesseecessseessseccsssecesseceesecesseeeenseeens 7 3 1 POWer and BANE 7 3 2 Main menu introduction sn a Baeeiaiehadsises 7 3 3 VIGEO EN 7 3 4 System information submenu 222022220002220000ssnnennnnnnnnnnnnnnsnnnnnnensnennennnnn 8 IDPIZleT an ea Ela 8 3 6 Video signal attenuation analyzing 0022000000ssssnneenssssnenssnnsnennennnnnennnnnn 9 3 7 Screen brightness AdjUStMeEN 0 ccc ccscccesecceseceessecesseecesseceeseeessaeeeses 10 320 UTP Cableilest ac na om R 10 3 7 Vid o generalinei ne mr rE ee eirchere 11 3 10 B5485 data EN ea ns An 11 3 11 Digital multimeter 0 0 0 ccc ccccsccccsseeccesseeeeesseeeeesseeeeessecceesseeseeseeeeeeseeesenaeees 12 3 12 Output power to CAMEL AL cc ccc ccesscccsseceeseeceesseceseeeeseeceeeeeesseeeseee
4. ation menu shows 25 the status number includes 100 90 75 50 25 5 please recharge it for use The tester can be used when it is being charged 3 2 Main menu introduction Turn on the device you will see the main menu as the following shows e 1 5 are five independent submenu e Press the corresponding number button to get into the submenu e Version number and S N can t be edited 1 SYSTEM SETUP 2 PTZ CONTROLLING 3 UTP TESTING 4 VIDEO GENERATING 5 RS485 DATAANALYZING 6 MULTI METER VER V1 09 S N 08110910 3 3 Video test gt System information gt PTZ controlling function gt UTP testing function gt Video generating function gt RS485 protocol analyzing gt Software version and S N CCTV Tester User s Manual Connect the output terminal of video output system to the video input BNC of tester turn on the tester the video can be displayed on the screen Connect the video output BNC of tester to the video input of other display device It can display the video signal generated by the tester or looped by tester 3 4 System information submenu A PROTOCOL Pelco P Press 1 to switch to the system information submenu as follows gt PTZ protocol COM 485 gt Communication port in used RATE 4800 gt Baudrate 2400 4800 9600 19200 SPEED 016 gt Pan and tilt speed IDLE TIME 000 gt Idle time from last operation to auto turn off minute BATTERY 0
5. eseeeeeseees 13 Warranty den ee a a RER 14 TTS ER 14 4 2 Warranty exception rrrrrrrnnrrrronnrrrrannrrrronnrrrrenvrrrnnnnrerannnnrnennnnrnnnnnrnnnnnvnsssnnvnssnnnvessnnnnee 14 4 3 Complemented 9 kp ee ee eee 14 CCTV Tester User s Manual 1 Safety Information 1 1 Precaution before using the tester A B Make sure to read the user s manual before using the product Make sure to check the input and output range of voltage or current at every input and output ports before connecting to prevent system overloading The following operational environment should be maintained constantly e Temperature 22 F 158 F 30 C 70 C e Relative humidity 30 90 e Recharging voltage DC5V 1 2 Precautions when using the tester OD OWD Do not use the tester in damp humidity or leaking gas environments Do not touch the tester with wet hands Be mindful not to shock or shake the tester while in use to avoid damage Avoid the places of strong magnetism or electric wave which could cause incorrect measuring Be careful not to expose the ports or joints to dirt or liquid Do not disassemble the tester 1 3 Precautions for battery charging and usage A B C Use only original chargeable battery when charging the batteries please use the original power adapter Make sure not to disorient the polarization of batteries Do not short circuit or disassemble batteries 2 Introduction 2 1 Features and
6. from the receiving day 2 Repairing service within 1 year change accessories and repair for free customers should responsible for the freight charge repairing service don t include battery 3 We provide whole life repairing service for our products with proper charge customers should be responsible for the freight charge 4 2 Warranty exception We provide repairing service with proper charge customers responsible for the freight charge 1 Damage caused by abuse unreasonable use mistreatment or neglect 2 Damage caused by modification or repair not authorized by our company working in hostile environments or natural disaster 3 Damage caused by improper or improperly used packaging or other devices work in the same system 4 3 Complemented items 1 Company is not responsible for other assurance and other derivative from capital loss The product and the user guides are not assured for particular users and some special purpose of use 2 Ifthe products returning for exchanging was damaged modified or miss accessory we will charge the proper payment 3 Ifthe components are no longer produced during the warranty limited period company will make a decision to replace similar products at no charge 4 Don t offer exchanging service for special design products by customers 15
7. function A Video test The video signal and the quality of picture can be tested PTZ controlling It has the basic operational test of PTZ products function include pan tilt zoom in out preset setting and operation speed adjustment etc support multiprotocol and baud rate communication via RS232 RS422 simplex and RS485 port RS485 protocol include Pelco D P Samsung Panasonic Molynx Additional Protocols may be added as per customer requests CCTV Tester User s Manual Baud rate include 2400 4800 9600 19200 C Power to camera The tester can output DC12V power to camera which is helpful if power supply is not available when testing a camera D Digital multimeter The tester can detect the AC DC voltage and resistance high testing range and precision can help installer find out the circuit problem E Video signal attenuation analyzing The tester can help installer to analyze the video signal attenuation by catching the video signal parameters F UTP cable test The wiring condition disconnected short of UTP cable can be tested and clearly shown on the screen G Video signal generating It can output Green white Black and Blue screen to allow technician to inspect video monitor or DVR The generating signal support PAL or NTSC don t support both meanwhile format H RS485 data test It can test the RS485 data sent from controlling device and display the hexadecimal data content for engineer to analyze 2 2 S
8. hows B Inthe main menu press the num button 4 to switch to the video generating function submenu as the follows Video Generating C Operation setup e Press num button 4 to switch to the video generating function mode e Press SET to switch the video generating signal Color bar Blue Red Pink Green Cyan Yellow and White e Press TELE to send the generated video signal to the display device e Press WIDE to recall the generated video signal e Press MENU button in short time to hid display the video generating menu character e Press MENU button for 1 second to back to the main menu 3 10 RS485 data test A Connect the tester to the controlling device as the picture shows 12 CCTV Tester User s Manual B In the main menu press num button 5 to switch to the RS485 protocol analyzing mode as follows DATA ANALYZING C Press SET to start the setup of baud rate D Press UP DOWN to select the tester s baud rate make it same with the controlling device s baud rate E Make the controlling device transfer the RS485 data to the tester the hexadecimal signal data will displayed on the screen as follows engineer can analyze the data to know if the controlling device works with the correct protocol DATA ANALYZING 00 01 00 00 00 00 00 00 00 00 00 00 01 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 3 11 Digital multimeter A Connect the 2 detecting cables on
9. ic signal number of camera is 0 3V tested by tester in the camera side after a long distance transmission via coaxial cable the synchronic signal number falls to 0 21V tested again by tester this means the attenuation of video signal via this coaxial cable is 30 User can evaluate if the quality of coaxial cable is good enough for this distance s usage e lf there is no signal is detected No Video will be displayed 3 7 Screen brightness adjustment At the mode of video and PTZ testing user can press the num button 7 BR and 9 BR to adjust the brightness of screen 3 8 UTP cable test A Connect the tester to the UTP cable tester as the picture shows B In the main menu mode press num button 3 to switch to the UTP testing mode C Press Set to start the test UTP cable information will be displayed in the screen D User can estimate the UTP cable connection situation from the information UTP CABLE TEST Sie ans 6 gt UTP tester side sequence HEER gt Q meansopen circuit CCTV o E S 5 ae os If there are 2 line show 0 it maybe Er e They open circuit separately sequence Er E 7 e They short circuit to each other B euer E User can estimate the connect situation based on the information F Press Menu button for 1 second to back to the main menu 11 CCTV Tester User s Manual 3 9 Video generating A Connect the tester to the displayer device as the picture s
10. otocol baud rate and the ID of the PTZ user can control the PTZ as follows Press UP DOWN LEFT RIGHT to control the movement of the PTZ Press OPEN CLOSE to control the iris Press FAR NEAR to adjust the focus manually Press WIDE TELE to zoom in out the camera lens Preset position Set up the preset position In the PTZ controlling mode press SPST button then input the preset position number by the num buttons press SET to save the setup operation user can use this method to set several preset positions one by one Calling the preset position In the PTZ controlling mode press the CPST button then input the preset position number by the num buttons press SET to save the setup operation user can use this method to call several preset positions one by one 3 6 Video signal attenuation analyzing At the mode of video and PTZ testing when there is an analogue video signal connected in and displayed on the screen correctly press the num button 1 to catch the parameter of video signal as MAX Vpp means the difference between maximum and minimum of video signal strength the video signal will be brighter when this parameter is larger AVERAGE Vpp means average of the difference between maximum and minimum of video signal strength 10 CCTV Tester User s Manual e SYNC SIGNAL means the voltage of the synchronic signal user can use this signal to evaluate the impedance of coaxial cable For example if the synchron
11. tandard items Battery 1 1 UTP cable tester BNC connect cable Multimeter cables 2 only for some Models Sa te CCTV Tester User s Manual 2 3 Function of each part Data Transmitting LED Data Receiving LED It lights when transmitting data It lights when receiving data Charge Indicating LED Power LED It is on when being charged It is on when the tester is on Glitters when charge finish 3 0 inch LCD Screen Open amp setup p P D O I 960x240 resolution ae CHARGE TX RX POWER Open iris amp setup the functions Close amp clear Close Iris amp clear the setup Menu Long press back to main menu Tele display hide sub menu To zoom in the PTZ lens amp send the generated video shift setup buttons signal out to the display Shifts up down right left for PTZ amp menus amp others me IRE Fag Wide To zoom out the PTZ lens amp NEUE NUMAS WIEN setup near recalls the generated video preset call preset amp PTZ ID BR BR op fom fa N He CCTY Tester device 0 9 num buttons Address Setup PTZ ID Far To adjust PTZ focus to far set preset Call preset Near In PTZ mode press to start In PTZ mode press to start To adjust PTZ focus to near to set preset to call preset CCTV Tester User s Manual RS232 port DC12V power output jack LY FY C SV k D UTP 4 OFF ON INPUT TEST ja FO
12. the tester as the picture shows 13 CCTV Tester User s Manual Press the num button 6 to open the multimeter submenu as follows DC 121 3mV 1 DC VOLTAGE 2 AC VOLTAGE 3 RESISTANCE C Press the num button 1 2 3 can select the corresponding option e DC voltage test range 01000V precision 0 1mV e AC voltage test range 750V precision 0 1mV e Resistance test range 040MQ precision 0 10 D Press MENU button for 1 second to return to the main menu Note Please don t test the voltage over the testing range it can break the tester 3 12 Output power to camera Connect the camera with the tester as the picture shows connect the DC12V output from tester to the DC12V input port from the camera using the accessory DC12V power cable 14 CCTV Tester User s Manual The working times of cameras vary due to camera consumption it can work for more than 4 hours if with a camera which consumption current is less than 100mA the maximum output current from tester is400mA Please use the proper camera Note 1 The output voltage of tester is DC12V please make sure it works with the proper camera 2 Please don t connect the output to the input of tester itself it can break the tester 4 Warranty 4 1 Warranty items Since the delivery day 1 Exchanging service within 15 days from the receiving day we responsible for the freight charge battery exchanging service within 90 days
Download Pdf Manuals
Related Search