User-RR.330 & RR.330A
Contents
1. 1 position OPERATION RRC and RRR have the same basic function Place the STOP RUN Switch in the STOP Position Place your Roll of Labels on the Roll Holder at the left of the Unit The Take Up Spindle on the right rotates in a counter clockwise direction Note that you can Wind In or Wind Out according to which way you place the Label Roll on the Roll Holder right side up or upside down There is a Butterfly Screw on the unwind Core Holder Hub Tightening this Screw will increase the braking effect Unwind tension Unscrew the Butterfly Screw for less tension or if the Core of the unwind roll is too tight on the unwind Hub The plastic Ring on the first paper guide needs to be used only if the unwind roll is unevenly wound to begin with Setting the Ring at the proper height will correct the unevenness of the Roll on the rewind side It is recommended to lower the speed if the unwind Roll is very uneven The machine will stop when out of labels To re start load labels on the Unwind Core Holder and place the STOP RUN Switch to STOP Thread the labels through the Photo Sensor Gap between the Idler Rollers Place an empty label Core not included over the Take Up Spindle and secure the Label Web using a piece of tape Start by switching to RUN THE UNIT WILL NOT RUN IF THERE IS NOTHING IN THE SENSOR RR 330 A ONLY USING THE ADJUSTABLE CORE HOLDER ACH Unlock the three Locking Levers underneath the ta2. 399 defective In no event shall Labelmate USA have any obligation to repair or replace until the customer 330 Fixed 3 Core Holder returns the defective product to Labelmate USA The customer assumes any and all responsibility and liability associated with transportation of products for service under this Warranty 33 0 A by 99 _ 4 2 A djustable Core Holder WARRANTY PERIOD PRODUCTS COVERED CAT and Mini CAT Label Rewinders Label Counters Excluding Counter Displays and Encoders Label Dispensers Excluding Counter Displays Label Slitters Mechanical Parts Only and excluding Counter 3 Years Displays Reel to Reel Machines Excluding Counter Displays and En coders Print Mechanisms Excluding Counter Displays and Encoders Quick Chucks Power Supplies AC DC Adaptors and Transformers Counter Displays Encoders Any other products or parts not specified herein In the event your product requires service or you have questions regarding Warranty coverage please call Remove all parts from shipping container and verify contents toll free 877 833 7149 inside the United States or 1 702 435 8535 outside the United States Variable Speed Control Bypass Switch for Maximum Speed High speed Motor Standard 13 330 mm Roll Diameter Capacity 1 Year LABELMATE MAKES NO OTHER WARRANTY OF ANY KIND WHETHER EXPRESS OR IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY SATISFACTORY QUALITY AND OR Package Contents FI
3. Place the RRC STOP RUN Switch in the STOP Position Place a Label Liner ONLY no label in the Label Sensor Gap Using a small flat bladed screwdriver adjust the Photocell Adjust Control until the green Photocell Adjust LED illuminates OR Adjust Photocell Adjust control for 3 to 5 VDC at the Photocell Test Jack 3 5 mm Plug Counter and Encoder option If you have the Encoder option for the RRC 330 330 A please see the enclosed Encoder Instruction Sheet for setup and operation When you switch to from the Counting to the Encoding Linear Mode you must remember to reset the Counter each time
4. Product Limited Warranty LABELMAT U SA LLC Labelmate USA warrants to the original end user customer that Labelmate USA products will be free from defects in materials and workmanship for the duration described herein below Labelmate USA s Limited Warranty covers only those defects that arise as a result of normal use of the products and does not cover any other problems including those that arise as a result of i improper maintenance or modification ii RR C 330 amp RR C 33 0 A parts or supplies not provided or supported by Labelmate USA iii operation outside the products specifications or iv unauthorized repair modification or misuse Use of any unauthorized accessory or attachment will void coverage RRR 330 amp RRR 33 0 A The Warranty period for all products commences the date of shipment from Labelmate USA and accrues to the original end user customer Warranty coverage is non transferable and terminates immediately upon rental resale or any other change in ownership Original purchase documentation should be retained for Reel to Reel Counter RRC Warranty coverage verification e e In the event Labelmate USA substantiates during the applicable Warranty period a defect in any product Unwinder Rewinder RRR which is covered by Labelmate USA s Warranty Labelmate USA shall repair or replace the product at Labelmate USA s option Labelmate USA retains sole discretion to determine whether or not a product is ei
5. TNESS FOR A PARTICULAR PURPOSE NO OTHER PERSON AGENT DEALER OR RESELLER IS AUTHORIZED TO GIVE ANY WARRANTIES ON BEHALF OF LABELMATE ANY OBLIGATION TO e Weer enuathiedecunent WARRANTY OTHER THAN THAT SPECIFICALLY ADDRESSED HEREIN IS EXPRESSLY DISCLAIMED e RRC 330 OR RRR 330 e Power Supply Module with Power Cord LABFELWATE USA uc e Separate User Manual for Counter Unit Retain the Shipping Container and Packaging for Storage and Transport 12A Sunset Way Henderson NV 89014 USA 702 435 8535 FAX 702 435 8536 e KEEP MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE Toll Free 877 833 7149 in USA support labelmateusa com www lf abelmateusa com WARNING This product is for indoor use only Not for use in wet locations Unplug unit before removing waste material or performing any cleaning or maintenance services A A SPECIFICATIONS Size Overall envelope HWD 13 x33 x9 330x584x229 mm Power Universal Power Supply 100 240vac 50 60Hz 50va Roll Width 6 5 170 mm Depending on Roll Diameter Core Diameter RR 330 Unwind amp Rewind 3 76 mm RR 330A Unwind 3 76 mm Rewind 1 4 25 100 mm RR 330 RR 330 A SET UP Plug the Power Supply Output Cable to the Power Jack on the Rear Panel of the RR 330 Plug the Power Supply into a suitable AC Power Outlet Rotate the SPEED Control to minimum full counter clockwise position Place the Power Switch on the rear of the RR 330 to the ON
6. ke up Flange by turning them clockwise If the Levers are difficult to grasp pull straight down on the Lever Arm and reposition the Arm so it is more or less perpendicular to the metal Hub While holding the Take Up Flange rotate the Black Plate underneath the Take Up Flange to bring the Fingers together Place your Take Up Core over the Fingers about half way down and rotate the Black Plate again to bring the Fingers in contact with the Core Lock the Locking Levers by turning them counter clockwise looking from the top Reposition the Lever Arms if necessary by pulling straight down and rotating them to a convenient position Push the Take Up Core all the way down on the Fingers The Core should now be held tight on the fingers If its not tight enough re do the operation For easy removal of the roll from the ACH release one of the Locking Levers temporarily remove the Roll and re tighten the Locking Lever Once the ACH diameter is set you can put the next empty core on the ACH without readjusting the Locking Levers NOTE Keep the Unwind Plate clean of particles and label adhesive The Bypass Switch on the side of the Unit will cause the RR to run at full speed approximately 10 faster than the maximum Adjustable Speed PHOTOCELL ADJUSTMENT The sensitivity of the Photocell that detects the Labels and triggers the Counter Display should be calibrated for the labels being counted Here s how
Download Pdf Manuals
Related Search