ATLAS 550 Quad BRI-U Module User Manual
Contents
1. Quad BRI U Module User Manual 61200315L1 1 Appendix A Dial Plan Configuration SOURCE ID Write security 3 Read security 5 Simplifies the creation of a DIAL PLAN in applications where the criterion for switching calls to a certain endpoint is a function of which endpoint origi nated the call e Default value 0 The default ID for all endpoints is 0 and for all accept numbers is 0 With default values all calls are routed based only on the dialed number e Multiple endpoints can have the same SOURCE ID e When creating the CALL ACCEPT list specify a SOURCE ID s as well as a dialed number or range of dialed numbers to accept EXAMPLE An application requires that all calls that originate from Port 1 of the Quad BRI U Module in Slot 1 be switched to Port 2 of that same module Assign a unique Source ID e g 7 to Port 1 of the module and then configure Port 2 to only accept calls from that unique Source ID 7 61200315L1 1 Quad BRI U Module User Manual A 5 Appendix A Dial Plan Configuration A 6 Quad BRI U Module User Manual 61200315L1 1 Index A ATLAS features used with Quad BRI U 3 6 ATLAS menus and submenus Alarm 3 3 Factory Restore 3 6 Menu 3 3 Modules 3 2 Rev 3 4 Run Selftest 3 6 Slt 3 2 State 3 3 Status 3 3 Test 3 3 Type 3 3 C circuit wiring 2 3 clock source tests 1 2 connectors 1 2 customer service vi D description of the Ouad BRI U module 1 1 F factory restor2. Quad BRIU Module asitie UN n ENT S PH A Asli EB 1 3 Figure 2 1 Installing the Quad BRI U Module 2 2 Figure 3 1 Modules MERU 4 1 5 55 1estsv ns a vaha ST Lust hk Se 3 2 Figure 3 2 Menu Tree for Quad BRI U Modules Menu ss 3 2 Figure 3 3 Quad BRI U Module Menu Options nn 3 4 Figure AT Dial Plan Men s MUMM dvi tise nl A 1 61200315L1 1 Quad BRI U Module User Manual xi List of Figures xii Quad BRI U Module User Manual 61200315L1 1 List of Tables Table 2 1 Network Pinout Connection 61200315L1 1 Quad BRI U Module User Manual xiii List of Tables xiv Quad BRI U Module User Manual 61200315L1 1 Chapter 1 Introduction QUAD BRI U MODULE OVERVIEW The Quad BRI U Module is a member of the ATLAS 550 family of integrat ed access products providing four Basic Rate ISDN BRI U interfaces each capable of operating in either NT or LT mode Any port can deliver timing for the system The Quad BRI U Module combines with the ATLAS 550 Base Unit and other ATLAS 550 modules to support requirements calling for multiple BRI circuits As many Quad BRI U Modules can be installed in a system as can be physically accommodated in the ATLAS 550 chassis Figure 1 1 shows a sample application using the Quad BRI U Module PBX en ATLAS 550 BRI T1 PRI Module PRI BRI a dd 1113 BRI Module Figure 1 1 Quad BRI U Module System When combined with the ATLAS 550 Base Unit and
3. optionally one or more Dual T1 PRI Modules P N 1200314L 1 the Quad BRI U Module can im plement an ISDN access switch combining multiple BRI circuits into one or more Primary Rate ISDN PRI circuits Functional Description The Quad BRI U Module installs in any available option slot in the ATLAS 550 chassis You can view the status of the module itself as well as the cir cuits to which it interfaces via the terminal menus accessible through either a VT 100 terminal connected to the ATLAS 550 control port or via a Telnet session established through the Base Unit s Ethernet port Use the terminal menu to configure the Quad BRI U Module and to download application software 61200315L1 1 Quad BRI U Module User Manual 1 1 Chapter 1 Introduction Features The following list describes the features of the Quad BRI U Module e Four BRI U Interfaces e Near end and far end block error monitoring e Can use any port as a timing source for the entire system e Hot swappable e NT and LT mode support e Maximum distance of 18 000 feet QUAD BRI U MODULE SPECIFICATIONS Each port of the Quad BRI U Module conforms to the following specifica tions Line rate 160 kbps data rate 80 kbaud signaling 5 ppm Line codes 2B10 Framing options Framing per ANSI T1 601 1992 e Clock source Allows any Quad BRI U Module port operating in NETWORK TERM mode to be the master timing source Tests Circuit self test loopback in
4. Service Profile Identifiers SPIDs and phone number s that match the SPID s and phone number s programmed into the ISDN switch for this line Each BRI may have one or more phone numbers and SPIDs The SPID LIST submenu defines these parameters to ATLAS The phone number s assigned to this BRI phone line This entry must match the SPID number s which have been set in the net work s ISDN switch or in the PBX for this BRI line A SPID must be entered for each phone number The number of calls 1 or 2 which can be received or sent on this number SPID These options reflect the network provisions for this SPID If the BRI was purchased with different services provisioned for the SPIDs then the call must match the services supported A 2 Quad BRI U Module User Manual 61200315L1 1 Appendix A Dial Plan Configuration STRIP MSD SOURCE ID Write security 3 Read security 5 Strips a selected quantity choose from NONE 1 2 and 3 of the Most Signif icant Digits MSD of a dialed number prior to being forwarded out of the port EXAMPLE A network port could be set to accept all calls beginning with 9 9 and then with STRIP MSD set to 1 all digits would be sent toward the network except the leading 9 including the MSDs that are subsequently stripped are used as accept criterion STRIP MSD does not affect CALL ACCEPT criteria All of the digits Write security 3 Read security 5 Simplifi
5. alters the equipment in any way other than as specifically authorized by ADTRAN EXCEPT FOR THE LIMITEDWARRANTY DESCRIBED ABOVE THE FOREGOING CONSTITUTES THE SOLE AND EXCLUSIVE REMEDY OF THE CUSTOMER AND THE EXCLUSIVE LIABILITY OF ADTRAN AND IS IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESSED OR IMPLIED ADTRAN SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES INCLUDING WITHOUT LIM ITATION ALL WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PUR POSE SOME STATES DO NOT ALLOW THE EXCLUSION OF IMPLIEDWARRANTIES SO THIS EXCLUSION MAY NOT APPLY TO CUSTOMER In no event will ADTRAN or its suppliers be liable to Customer for any incidental special punitive exemplary or consequential damages experienced by either Customer or a third party including but not limited to loss of data or information loss of profits or loss of use ADTRAN is not liable for dam ages for any cause whatsoever whether based in contract tort or otherwise in excess of the amount paid for the item Some states do not allow the limitation or exclusion of liability for incidental or con sequential damages so the above limitation or exclusion may not apply to Customer vii viii Table of Contents List Of Figures ccsssssscssssssssscssssssssssscsesecssssssesesoesssssseseseesssssseseesesessssessesesessasesensesessesencesesseseseseseseesessesesesoeees xi List of Tables RAN xiii Chapter 1 Introduction eriein eee san ea sens essieu e
6. an authorized Canadian maintenance facility desig nated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power util ity telephone lines and internal metallic waterpipe system if present are connected together This precaution may be particularly important in rural areas Users should not attempt to make such connections themselves but should contact the appropriate CAUT electric inspection authority or an electrician as appropriate The Load Number LN assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device to prevent overloading The termination on a loop may consist of any combination of devices subject only to the equipment that the total of the LNs of all devices does not exceed 100 The ringer equivalence number REN assigned to each terminal adapter is used to determine the total number of devices that may be connected to each circuit The sum of the RENs from all devices in the circuit should not exceed a total of 5 0 Warranty and Customer Service ADTRAN will replace or repair this product within five years from the date of shipment if the product does not meet its published specification or if it fa
7. on the selected port If connected to another ATLAS both need to be set to the same type Choices include LUCENT 5E NORTHERN DMS 100 and NATIONAL ISDN Write security 3 Read security 5 The port acting as the network must use a SPID and a phone number in order to satisfy the ISDN connection protocol expected by the user s Termi nal Adapter TA The phone number s assigned to this BRI phone line Defines the SPID number s used for this BRI line Although the value of the SPID is not significant a SPID must be entered for each phone number Ku The Quad BRI U Module does not support autoSPID detection software which some terminal adapters offer The number of calls 1 or 2 which can be received or sent on this number SPID These options reflect bearer capability provisions for this SPID If this is changed from default then the call type must match the services supported Write security 3 Read security 5 Strips a selected quantity choose from NONE 1 2 and 3 of the Most Signif icant Digits MSD of a dialed number prior to being forwarded out of the port EXAMPLE A network port could be set to accept all calls beginning with 9 9 and then with STRIP MSD set to 1 all digits would be sent toward the user equipment except the leading 9 including the MSDs that are subsequently stripped are used as accept criterion N STRIP MSD does not affect CALL ACCEPT criteria All of the digits A 4
8. type of module actually installed in the slot or the type of module you plan to install in the slot Ifa Quad BRI U Module is installed the Type field automatically defaults to U BRI the Quad BRI U Module You can use this field to preconfigure a system before actually installing modules by simply specifying the module that you want to install in each slot want to preconfigure the slot for a different type of module you must set this field to EMPTY before selecting another module type N TYPE automatically displays the name of an installed module If you Displays additional status and configuration menus for the selected module To access the submenus for this item use the arrow keys to scroll to the Menu column for the module you want to edit and press Enter For detailed information on each submenu item see the section Ouad BRI U Module Menus on page 3 4 Read security 5 Displays an alarm condition on the Ouad BRI U Module Press Enter in this field to activate the menu Read security 5 Displays test name if the Ouad BRI U Module is executing a test Press Enter in this field to activate the menu This menu can activate a local loop back toward the U interface LOC U LB for each port PRT The loop back options include B1 LOOPBACK B2 LOOPBACK or ALL Displays module status as either ONLINE of OFFLINE Even though a module is physically installed it must be marked as online for it to be considered an available
9. ADIRAN Quad BRI U Module User Manual Part Number 1200315L1 61200315L1 1B April 2000 ADRAN 901 Explorer Boulevard P O Box 140000 Huntsville AL 35814 4000 256 963 8000 2000 ADTRAN Inc All Rights Reserved Printed in U S A Affidavit Requirements for Connection to Digital Services An affidavit is required to be given to the telephone company whenever digital terminal equipment without encoded analog content and billing protection is used to transmit digital signals containing encoded analog content which are intended for eventual conversion into voiceband analog signals and transmitted on the network The affidavit shall affirm that either no encoded analog content or billing information is being transmitted or that the output of the device meets Part 68 encoded analog content or billing protec tion specifications End user customer will be responsible for filing an affidavit with the local exchange carrier when connecting unprotected customer premise equipment CPE to 1 544 Mbps or subrate digital ser vices Until such time as subrate digital terminal equipment is registered for voice applications the affi davit requirement for subrate services is waived Affidavit for Connection of Customer Premises Equipment to 1 544 Mbps and or Subrate Digital Services For the work to be performed in the certified territory of telco name State of County of I name business address telep
10. Y REVISION Figure 3 3 shows the menu options available for the Quad BRI U Module see also the menu tree in Figure 3 2 on page 3 2 The following sections de scribe these options odule Alarms Alarm Test Activity Channel Status Performance Current Configuration Test Figure 3 3 Quad BRI U Module Menu Options Accesses additional submenus Provides information about module part number serial number and assem bly revision Displays the part number of the module read only Displays the serial number of the module read only Displays the assembly revision of the module read only 3 4 Quad BRI U Module User Manual 61200315L1 1 Chapter 3 Operation ALARM PRT ALARMS CHANNEL STATUS PRT CHA PERFORMANCE CURRENT CONFIGURATION TEST MODULE ALARMS TEST ACTIVITY Displays port number and alarms Indicates the port number Lists the alarms Displays the status of each of the Quad BRI U Module ports Displays the port number Channel Displays the status of individual channels The following symbols may display Unallocated channel Inactive channel B Active Bchannel D Active D channel The Performance Current field displays a count of Near End Block Errors NEBE and Far End Block Errors FEBE for each port PRT Allows the user to personally identify each port PRT with an appropriate name PORT NAME The default for all ports is Ouad BRI U Module Activates a lo
11. aan n Raisin sentent ina nl 3 4 Rev tard 3 4 Quad BRI U Module Menus 0 ccccccccssscecsscesseceseeessecsececsscessecesscesseceseecseecsacesacesesesaecsececsaeeeaaessetesseeesseces 3 4 TEBRI Meh US s 2 22 A PO mn DE e EI Baath eae dea Sea doe 3 4 Orne A lin innen EA Che dunes OA pea E In Ma sab a sage kes TULED ST 3 4 Part Numbers d mme aisladas 3 4 Serial Number ST 3 4 61200315L1 1 Quad BRI U Module User Manual ix Table of Contents Assembly REVISION rendit Sakk polonia 3 4 Alarm tissu AA ias 3 5 Piki SR RE an SNE din KA SEN KS EE ne REN a EER 3 5 INV ATT emakas laada Daa AA kanade is Se 3 5 Channel Status shit is nt tient dior ill et 3 5 A E Re en rer tienne ire lb tente bea Soe ae nl uniaan ms aikaa 3 5 Chain TE Nea SSE SA OEE ASS 3 5 Performance Current seks erat ke Rain le SANE IISA R IRAN asa incite 3 5 Configuration obscuridad 3 5 Tossa SR t t 3 5 Module ATA MS kige tina A ann ed ONNINEN Ses tre te en 3 5 Test AcHVily en ER ne AT RA NAR Unn dp Mer les ATA OITIS AIR AMT SAN Oa sn na 3 5 ATLAS Features Used with Quad BRI U Module Options ss 3 6 Factory Restore LE pases Sosa neo ne in unse a E L 3 6 Run elena STEN MESA Tent SINA NN ED NASAN Ca Sets SSS danse SEN BERS 3 6 Appendix A Dial Plan Configuration ss A 1 Index osisssa EPE AA MR dre dettes ed tr E con din nettes TA Index 1 X Quad BRI U Module User Manual 61200315L1 1 List of Figures Figure 1 1 Quad BRI U Module System ss 1 1 Figure 1 2
12. ble Technical Support 888 4ADTRAN Repair and Return If ADTRAN Technical Support determines that a repair is needed Technical Support will coordinate with the Custom and Product Service CAPS department to issue an RMA number For information regarding equipment currently in house or possible fees associ ated with repair contact CAPS directly at the following number CAPS Department 256 963 8722 Identify the RMA number clearly on the package below address and return to the follow ing address ADTRAN Customer and Product Service 6767 Old Madison Pike Building 6 Suite 690 Huntsville Alabama 35807 RMA
13. cal loopback toward the U interface LOC U LB for each port Prt The loopback options include B1 LOOPBACK B2 LOOPBACK or ALL Provides a shortcut to the ALARM menu see Alarm on page 3 5 Provides a shortcut to the TEST menu see Test on page 3 5 61200315L1 1 Quad BRI U Module User Manual 3 5 Chapter 3 Operation ATLAS FEATURES USED WITH QUAD BRI U MODULE OPTIONS FACTORY RESTORE RUN SELFTEST Two additional ATLAS menu items can operate in conjunction with the Quad BRI U Module FACTORY RESTORE and RUN SELFTEST You can restore the factory default settings for an Quad BRI U Module by pressing F either while the cursor is over the SLT number this action re stores the factory settings for all of the module options or while the cursor is over an individual field this action restores factory settings only for the particular field RUN SELFTEST asubmenu of the ATLAS main menu item TEST executes both the Quad BRI U Module internal test and the ATLAS internal test For additional information on RUN SELFTEST see the ATLAS User Manual When RUN SELFTEST displays place the cursor on it and press Enter to exe cute the test The unit continuously changes the display on the self test log screen until all test results are shown 3 6 Quad BRI U Module User Manual 61200315L1 1 Appendix A Dial Plan Configuration DIAL PLAN OVERVIEW The DIAL PLAN menu see Figure A 1 sets configuration parameters fo
14. ccordance with the instruction manual may cause harmful interference to radio freguencies Operation of this eguipment ina residential area is likely to cause harmful interference in which case the user will be reguired to correct the interference at his own expense Shielded cables must be used with this unit to ensure compliance with Class A FCC limits Change or modifications to this unit not expressly approved by the party responsible for compliance CAUT could void the user s authority to operate the eguipment Canadian Equipment Limitations The Industry Canada Certification label identifies certified equipment This certification means that the equipment meets certain telecommunications network protective operational and safety requirements The Department of Commerce does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facil ities of the local telecommunications company The equipment must also be installed using an accept able method of connection In some cases the company s inside wiring associated with a single line individual service may be extended by means of a certified connector assembly telephone extension cord The customer should be aware that compliance with the above conditions may not prevent deg radation of service in some situations Repairs to certified equipment should be made by
15. e using training mate rials and instructions provided by the manufacturer grantee of the equipment used to encode analog signals or An independent training course e g trade school or technical institution recognized by the manufacturer grantee of the equipment used to encode analog signals or D Inlieu of the preceding training requirements the operator s maintainer s is are under the control of a supervisor trained in accordance with circle one above I agree to provide telco s name with proper documentation to demonstrate compliance with the information as provided in the preceding paragraph if so requested Signature Title Date Transcribed and sworn to before me this day of 3 Notary Public My commission expires FCC regulations require that the following information be provided in this manual to the customer 1 This equipment complies with Part 68 of the FCC rules The required label is affixed to the bottom of the chassis 2 An FCC compliant telephone cord and modular plug is provided with this equipment This equip ment is designed to be connected to the telephone network or premises wiring using a compatible modular jack which is Part 68 compliant See Chapter 2 Installation for details 3 If your telephone equipment Octal BRI U Module causes harm to the telephone network the tele phone company may discontinue your service temporarily If possible they will
16. e 3 6 failed self test 2 3 FCC statement v framing options 1 2 I installing the Quad BRI U module 2 1 introducing the Quad BRI U module 1 1 L limited product warranty vii line codes 1 2 line rate 1 2 N network pinouts 2 3 network termination on the Quad BRI U A 2 O operating the Ouad BRI U module 3 1 operation alarms 2 3 p physical description of the Ouad BRI U 1 3 pinouts 2 3 power up 2 3 R RMA reguests vi S scrolling through the menus 3 2 service vi specifications for the Quad BRI U module 1 2 T terminal menu structure 3 1 U U BRI menus and submenus Alarm Alarms 3 5 Prt 3 5 Channel Status 3 5 Cha 3 5 Prt 3 5 Configuration 3 5 Performance Current 3 5 SPID List network termination A 2 SPID List user termination A 4 Switch Type network termination A 2 Switch Type user termination A 4 user termination on the Quad BRI U A 3 W warranty vi 61200315L1 1 Quad BRI U Module User Manual Index 1 Index Index 2 Quad BRI U Module User Manual 61200315L1 1 Product Support Information Pre sales Inquiries and Applications Support Please contact your local distributor ADTRAN Applications Engineering or ADTRAN Sales Applications Engineering 800 615 1176 Sales 800 827 0807 Post Sale Support Please contact your local distributor first If your local distributor cannot help please con tact ADTRAN Technical Support and have the unit serial number availa
17. e User Manual 3 1 Chapter 3 Operation MODULES MENU The ATLAS system controller automatically detects the presence of the Quad BRI U Module when it is installed in the system To see the menus for the Quad BRI U Module via the terminal menu use the arrow keys to scroll to the MODULES menu and press Enter to access the module choices Figure 3 1 shows the MODULES menu see also the menu tree in Figure 3 2 The fol lowing sections describe all of the MODULES menu options ystem Info System Status System Config System Utility Modules Packet Manager lt No Response No Response Empt pty No Response mpty Online Online No Response Empty IA pole Figure 3 1 Modules Menu Slt Info Part Number Type Serial Number U BRI Menus Assembly Revision Menu Module Alarms Alarm Prt shortcut Alarms Modules Channel Status Prt Cha Alarm Test Performance Prt State Current NEBE Status FEBE Rev Configuration Prt Port Name Test Activity Test Prt shortcut LOC U LB Figure 3 2 Menu Tree for Quad BRI U Modules Menu SLT Read security 5 Displays the number of the available slots in the ATLAS chassis Slot 0 refers to the ATLAS unit This field is read only 3 2 Quad BRI U Module User Manual 61200315L1 1 Chapter 3 Operation TYPE MENU ALARM TEST STATE STATUS ONLINE Write security 3 Read security 5 Displays the
18. ed to be serviced by qualified service N ARNING personnel only 2 2 Quad BRI U Module User Manual 61200315L1 1 Chapter 2 Installation WIRING Each module port uses a single RJ 45 jack to connect to a U interface circuit Table 2 1 shows the network pinout connection The required wiring con nection follows Connector Type USOC RJ 45 Table 2 1 Network Pinout Connection PIN NAME DESCRIPTION 1 2 3 6 7 8 Unused 4 Ring Ring to and from the Network Interface 5 Tip Tip to and from the Network Interface POWER UP AND INITIALIZATION The Ouad BRI U Module reguires no initialization input during the power up seguence as described in the ATLAS User Manual Any previously con figured setting for the Ouad BRI U Module is automatically restored upon power up Failed Self Test If the Quad BRI U Module fails self test a message will be displayed on the terminal menu self test log See the ATLAS User Manual for details Operation Alarms The red ALARM LED located with the Module LEDs on the front panel il luminates when an alarm condition is detected An interface alarm is shown for each port in the Alarm Menu of the Ouad BRI U Module 61200315L1 1 Quad BRI U Module User Manual 2 3 Chapter 2 Installation 2 4 Quad BRI U Module User Manual 61200315L1 1 Chapter 3 Operation OVERVIEW You can control and configure the Quad BRI U Module from a variety of sources including the foll
19. es the creation of a DIAL PLAN in applications where the criterion for switching calls to a certain endpoint is a function of which endpoint origi nated the call e Default value 0 The default ID for all endpoints is 0 and all accept numbers is 0 With default values all calls are routed based only on the dialed number e Multiple endpoints can have the same SOURCE ID e When creating the CALL ACCEPT list specify a SOURCE ID s as well as a dialed number or range of dialed numbers to accept EXAMPLE An application requires that all calls that originate from Port 1 of the Quad BRI U Module in Slot 1 be switched to Port 2 of that same module Assign a unique Source ID e g 7 to Port 1 of the module and then configure Port 2 to only accept calls from that unique Source ID 7 Quad BRI U Module User Termination While interfacing to user equipment terminal adapters the Quad BRI U Module acts like the network and should be configured in the USER TERM section of the Dial Plan accordingly When you are working in the USER TERM section of the DIAL PLAN menu and SLT is defined as U BRI 4 the fol lowing interface configuration options are available 61200315L1 1 Quad BRI U Module User Manual A 3 Appendix A Dial Plan Configuration SWITCH TYPE SPID LIST PHONE NUMBER SPID NUMBER CALLS D64 D56 AUDIO SPEECH STRIP MSD Write security 3 Read security 5 Defines the ISDN switch protocol to be emulated
20. hone number being duly sworn state I have responsibility for the operation and maintenance of the terminal equipment to be connected to 1 544 Mbps and or subrate digital services The terminal equipment to be connected com plies with Part 68 of the FCC rules except for the encoded analog content and billing protection speci fications With respect to encoded analog content and billing protection Iattest that all operations associated with the establishment maintenance and adjustment of the digital CPE with respect to analog content and encoded billing protection information continu ously complies with Part 68 of the FCC Rules and Regulations The digital CPE does not transmit digital signals containing encoded analog content or billing information which is intended to be decoded within the telecommunications network The encoded analog content and billing protection is factory set and is not under the control of the customer I attest that the operator s maintainer s of the digital CPE responsible for the establishment mainte nance and adjustment of the encoded analog content and billing information has have been trained to perform these functions by successfully having completed one of the following check appropriate blocks A A training course provided by the manufacturer grantee of the equipment used to encode analog signals or B A training course provided by the customer or authorized representativ
21. ils while in service For detailed warranty repair and return information refer to the ADTRAN Equipment Warranty and Repair and Return Policy Proce dure see the last page of this manual A return material authorization RMA is required prior to returning equipment to ADTRAN For service RMA requests or more information see the last page of this manual for the toll free contact number vi Limited Product Warranty ADTRAN warrants that for five 5 years from the date of shipment to Customer all products manu factured by ADTRAN will be free from defects in materials and workmanship ADTRAN also war rants that products will conform to the applicable specifications and drawings for such products as contained in the Product Manual or in ADTRAN s internal specifications and drawings for such prod ucts which may or may not be reflected in the Product Manual This warranty only applies if Cus tomer gives ADTRAN written notice of defects during the warranty period Upon such notice ADTRAN will at its option either repair or replace the defective item If ADTRAN is unable in a rea sonable time to repair or replace any equipment to a condition as warranted Customer is entitled to a full refund of the purchase price upon return of the equipment to ADTRAN This warranty applies only to the original purchaser and is not transferable without ADTRAN s express written permission This warranty becomes null and void if Customer modifies or
22. notify you in ad vance But if advance notice isn t practical you will be notified as soon as possible You will be advised of your right to file a complaint with the FCC 4 Your telephone company may make changes in its facilities equipment operations or procedures that could affect the proper operation of your equipment If they do you will be given advance notice to give you an opportunity to maintain uninterrupted service 5 If you experience trouble with this equipment Octal BRI U Module please contact ADTRAN at 256 963 8000 for repair warranty information The telephone company may ask you to discon nect this equipment from the network until the problem has been corrected or until you are sure the equipment is not malfunctioning This unit contains no user serviceable parts 7 The following information may be required when applying to your local telephone company for leased line facilities a Service Type REN SOC FIC USOC Basic Rate ISDN 6 0N 021S5 RJ 48C Federal Communications Commission FCC Radio Freguency Interference Statement This eguipment has been tested and found to comply with the limits for a Class A digital device pur suant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the eguipment is operated in a commercial environment This eguipment generates uses and can radiate radio freguency energy and if not installed and used in a
23. owing e The terminal menus both VT 100 and Telnet sessions allowing de tailed configuration status and diagnostics The remainder of this section describes the menu items presented when managing the Quad BRI U Module via the terminal menu Access the terminal menu using either a VT 100 terminal attached to the ATLAS Base Unit s control port or a Telnet session established through the Base Unit s Ethernet port The ATLAS User Manual provides detailed instructions on the operation of each of these management approaches To edit items in the terminal menu you must have the appropriate password level Each menu description in this section indicates the password level required for write and read access See Access Passwords in the ATLAS User Manual for detailed information on working with passwords Security level 0 users can view and edit every available field Security level 5 users can view any field but cannot edit TERMINAL MENU STRUCTURE ATLAS uses a hierarchical menu structure to provide access to all of its fea tures The top most menu level leads to submenus which are grouped by functionality All menu items display in the terminal window To access the Quad BRI U Module activate the MODULES menu The following sections describe the menu items for the MODULES menu navigating through the terminal menu Lu Refer to the ATLAS User Manual for detailed instructions on 61200315L1 1 Quad BRI U Modul
24. pping Contents The ADTRAN shipment includes the following items e Quad BRI U Module e Quad BRI U Module User Manual insert into the ATLAS User Manual e Four RJ 45 to RJ 11 cables ADTRAN P N 3125M007 INSTALLING THE QUAD BRI U MODULE Figure 2 1 on page 2 2 represents the actions required to properly install the Quad BRI U Module as described in the step action table on page 2 1 The four Option slots labeled 1 4 only accept Option Modules and the Network Interface slots labeled Network 1 and Network 2 only accept Network Interface Modules See the ATLAS 550 in Figure 2 1 on page 2 2 61200315L1 1 Quad BRI U Module User Manual 2 1 Chapter 2 Installation Instructions for Installing the Quad BRI U Module Step Action 4 Remove the cover plate from the appropriate option slot in the ATLAS rear panel 2 Slide the Quad BRI U Module into the option slot until the module is firmly positioned against the front of the chassis 3 Secure the thumbscrews at both edges of the module Tighten with a screwdriver 4 Connect the cables to the associated device s Complete installation of remaining modules and Base Unit as 5 specified in the Installation chapter of the ATLAS 550 User Manual Remove Cover Plate fuse ran ETHERNET CONTROL o O IN OUT MON NO NO CON GND Figure 2 1 Installing the Quad BRI U Module Option modules are intend
25. r each switched endpoint These parameters vary by the type of port selected The following sections describe the configuration options available for the Quad BRI U Module The DIAL PLAN menus are only accessible when using a VT 100 or Telnet session To access these options select DIAL PLAN from the top level menu User Term Global Param Figure A 1 Dial Plan Menus QUAD BRI U MODULE CONFIGURATION This section describes the NETWORK TERMINATION and USER TERMINATION configuration settings for the Quad BRI U Module when using the DIAL PLAN menus e See Quad BRI U Module Network Termination on page A 2 e See Quad BRI U Module User Termination on page A 3 61200315L1 1 Quad BRI U Module User Manual A 1 Appendix A Dial Plan Configuration Quad BRI U Module Network Termination SWITCH TYPE SPID LIST PHONE NUMBER SPID NUMBER CALLS D64 D56 AUDIO SPEECH The Ouad BRI U Module can interface directly with the network PSTN and should be configured in the NETWORK TERM section of the DIAL PLAN ac cordingly When you are working in the NETWORK TERM section of the DIAL PLAN menu and SLTis defined as U BRI 4 the following interface configu ration options are available Write security 3 Read security 5 Defines the ISDN switch protocol provided by the PSTN on the connected port Write security 3 Read security 5 To properly operate with a network PSTN ISDN switch the BRI interface must have
26. resource This parameter allows an installed module to be marked as offline which may be useful in system troubleshooting If you choose to mark a module as offline the module will not be in alarm condition but will display OFFLINE the ATLAS to use the module for any data bandwidth Lu Once a module is installed the state must be set to Online in order for This read only field provides status information on the Quad BRI U Module The following messages may display The module is enabled and is responding to the system controller s status polls This is the normal response of the system 61200315L1 1 Quad BRI U Module User Manual 3 3 Chapter 3 Operation No RESPONSE EMPTY OFFLINE OFFLINE NO RESPONSE REV The module is enabled but is not responding to the system controller s sta tus polls This response indicates either a problem in the system or that the module is not installed The system controller has not detected the presence of a module in the slot nor has a module been manually enabled for this option slot The module is installed but has been taken Offline by a user The module is still responding to controller polls The module is installed but has been taken Offline by a user The module is not responding to polls This read only field displays the assembly revision of the Quad BRI U Module QUAD BRI U MODULE MENUS U BRI MENUS INFO PART NUMBER SERIAL NUMBER ASSEMBL
27. ss 1 1 Quad BRI U M dul Overview RR a Nr 1 1 Functional Description sene suin ea ae enlarge nenne 1 1 ESAS most mei nn N hin ii te KA alt es len Rene rd at 1 2 Quad BRI U Module Specifications sisi 1 2 Physical Description RAR en en in es 1 3 Chapter 2 Installatiomissiccsissciscscctcessesesssanveccicnssevensessusnsosenstecensssesonchonbissedusstesebensisceubedsseneatenseseavtedestiedecssacees 2 1 Before Installing the Quad BRI U Module 2 1 Shipping Contents ee sth Date ata seas baht A N A KANI par un abt dem EE 2 1 Installing the Quad BRI U Module ss 2 1 WN TENT NS 2 3 Power Up and hiti liZ tiOfi isisslisassa i a de sa ena een due n cs slaves 2 3 Failed Self 0 GS te sn hi io lia dada Has stead Taika n ANI 2 3 Operation Alar ns Tue an stan te Te Re AITA a e Nang SE massa 2 3 Chapter 3 Operation tench suptsenvuonensivetessuansscoesoncvesentesesdesuiecensvenssddenus 3 1 IVIVE TR EEEE M den sh AA TA RENTE 3 1 Terminal Menu Structures ses Soe ai 3 1 Modiles MEN a ln RT SSD 3 2 SIE st SRE PT An AO Et A tte den srl es ds 3 2 Typen aber ein Says ne a se nt a lis ets kde alan SES nets 3 3 Menu Lesh an Dc eds S SES SSS YAI de MS 3 3 ATADO AA A A A Ka S IAS MAAN T suin aikas 3 3 Mais 3 3 e O 3 3 AU a a Sista SI A Cas OA oa ees 3 3 A TUNESTA NN NN 3 3 NO Responses sstsita ic radiales idas 3 4 ETP EY amma InI nn nant tia On Mamma hmm uneksia 3 4 OHIMENNEN NTT SNS IKEEN ASM MN e Aa 3 4 Offlin No Response an mass
28. ternal toward network or user equipment BRI switch support Provides support for the following switches AT amp T 5ESS NT or LT Nortel DMS 100 NT or LT National ISDN 1 Line performance data Reported via SNMP in RFC1406 format Connectors RJ 45 1 2 Quad BRI U Module User Manual 61200315L1 1 Chapter 1 Introduction PHYSICAL DESCRIPTION The Quad BRI U Module see Figure 1 2 plugs into any available option slot in the rear of the ATLAS chassis The four Option slots labeled 1 4 only accept Option Modules and the Network Interface slots labeled Network 1 and Network 2 only accept Network Interface Modules See the ATLAS 550 in Figure 2 1 on page 2 2 0 EE Figure 1 2 Quad BRI U Module The label over each RJ 45 connector refers to the port on the Quad BRI U Module 61200315L1 1 Quad BRI U Module User Manual 1 3 Chapter 1 Introduction 1 4 Quad BRI U Module User Manual 61200315L1 1 Chapter 2 Installation BEFORE INSTALLING THE QUAD BRI U MODULE Carefully unpack and inspect the Quad BRI U Module for shipping damag es If you suspect damage occurred during shipping file a claim immediate ly with the carrier and then contact ADTRAN Technical Support see the last page of this manual for pertinent information If possible keep the original shipping container for returning the Quad BRI U Module for repair or for verification of shipping damage Shi
Download Pdf Manuals
Related Search