Home

1 User manual

1. 801 letters or numbers 0 20 digits user password Change the user name under the GPRS mode Description After the instruction is executed the user name of the terminal under the GPRS mode will be set according to the requirements After successful setting 801 CONFIG OK will be returned to the phone if the password is wrong 801 PASSWORD ER will be returned e g 801 13900139000 0000 After the instruction is executed the user name is 13900139000 802 APN letters or numbers 4 26 digits login user name letters or numbers 4 20 digits login password letters or numbers 4 20 digits user password Set the APN Description After the instruction is executed the terminal APN under the GPRS mode will be set according to the requirements After successful setting 802 CONFIG OK will be returned to the phone if the password is wrong 802 PASSWORD ER will be returned e g 1 802 CMNET 0000 After the instruction is executed the terminal APN is CMNET the login user name and password are blank e g 2 802 CCDLEN QIUXIA 21 RX 0000 After the instruction is executed the APN is CCDLEN the login user name is QIUXIA 21 and the login password is RX Note The default APN of this product is CMNET 751 fence radius meter sampling interval minute latitude longitude u ser password Set the electronic fence Description After successful setting
2. 760 CONFIG OK to the phone If the password is wrong 760 PASSWORD ER will be returned e g 760 0000 901 Read the user parameters 902 Read the GPRS parameters 90444 Connect to the GPRS 905 Disconnect to the GPRS Precautions This equipment is of non waterproof design The equipment shall work under the GSM GPRS network environment Make sure that there is sufficient balance in the SIM card account so as to avoid inconvenience The equipment can not work under power off status or outside the service area even you are a registered user This equipment supports GPS and GSM GPRS dual positioning mode Please use this equipment in the areas permitted by law Any consequence arising from violation of the laws shall be solely borne by the user Dyn OR D Note As this product adopts a GPS module of high sensitivity it is normal for drift in the case of weak GPS signal
3. Example 730 20 4 0000 Notes The parameter 20 indicates getting one point every 20s after getting points accumulatively for 4 times upload one piece of positioning information with the upload interval as 20 4 80s The user may change this parameter as the case may be 730 0 1 0000 the GPS is turned off and the timed return function is deactivated 803 fixed IP address port number user password This instruction is used to set the GPRS center server address The server address can either be a fixed IP whose format is xxx XXX XXX xxx Or a domain name whose length is less than 64 bytes After successful setting amp 803 amp CONFIG OK amp amp will be returned to the phone if the password is wrong amp 803 amp PASSWORD ER amp amp will be returned e g 803 120 149 139 114 30000 0000 It can also be set through the domain name e g 803 www xxx com 30000 0000 666 user password Single location query a message about the latitude and longitude will be returned 770 new password old password Description After the instruction is executed the terminal will change the user password according to the user s requirements After successful setting 770 CONFIG OK will be returned to the phone if the password is wrong 770 PASSWORD ER will be returned e g 770 1111 0000 After the instruction is executed the user password changes from 0000 to 1111
4. 751 CONFIG OK will be returned if the password is wrong 751 PASSWORD ER will be returned e g 751 5000 5 2232 6208N 11354 6378E 0000 After the instruction is executed the fence of 5 km radius is set for the terminal when the terminal leaves the area the fence alarm message will be sent to the center number 752 user password Read the electronic fence After the instruction is successfully sent the terminal reads the work status data of the fence and returns it to the phone If the password is wrong amp 752 amp PASSWORD ER amp amp will be returned e g 752 0000 The following will be returned open 1 lat 22 54368N Ing 113 91063E distance 500 time 5 status 2 Wherein open 1 refers to the activation of the fence open 0 refers to the deactivation of the fence lat 22 54368 refers to the latitude N S Ing 113 91063 refers to the longitude E W distance 500 refers to the radius of the fence time 5 refers to the sampling interval status 2 refers to that the terminal gets valid satellite data and the fence works normally status 1 refers to that the fence is activated but the terminal fails to get valid satellite data status 0 refers to that the electronic fence is not set 760 user password Cancel the electronic fence Description After the instruction is executed the terminal cancels the fence function After successful setting the terminal returns
5. Subminiature GPS Vehicle Tracker User Manual 1 Definition of external wiring PIN 1 V RL RX SOS ON MIC BAT PIN 13 PIN 2 V RL TX TA GND MIO BAT PIN 14 Pin 1 External power input positive voltage range DC 6V 24V Pin 2 External power input negative connected to GND Pin 3 Relay control output positive voltage 12V forbidden from connecting to GND during operation Pin 4 Relay control output negative connected to GND Pin 5 Debug port RX signal Pin 6 Debug port TX signal Pin 7 Emergency alarm signal input SOS high level under normal circumstances low level input to enable SOS alarm Pin 8 External status signal input TA low level under normal circumstances high level input indicates occurrence of external events Pin 9 Overall power on signal input ON high level under normal circumstances low level input to enable power on Pin10 External input signal reference ground connected to GND Pin11 External microphone input positive MIC Pin12 External microphone input negative MIC Pin13 External battery input positive BAT input voltage 3 6 4 2V the equipment may be permanently damaged if the input voltage exceeds the specified range Pin14 External battery input negative BAT connected to GND 2 Installation of SIM card Remove the shell and install the SIM card as illustrated below Beveled Corner of SIM Card Installation of SIM Card 3 After the SI M card is in
6. hone number 2 phone number 3 user password Set the preset numbers through the message sent by a mobile phone After successful setting the mobile phone will receive the message amp 711 amp CONFIG OK amp amp returned by the terminal e g 1 711 13800000001 413800000002 13800000003 0000 e g 2 711 13800000001 4 0000 After successful setting the terminal returns 711 CONFIG OK to the mobile phone if the password is wrong 711 PASSWORD ER will be returned 720 alarm mode0 3 user password Set the terminal alarm mode Alarm mode 0 No alarm Alarm mode 1 Dialing alarm Alarm mode 2 Message alarm Alarm mode 3 Dialing alarm Message alarm Note When the back cover is removed The terminal will give an alarm according to the preset alarm mode e g 720 3 0000 After the instruction is executed the terminal alarm mode is set as dialing alarm message alarm when the alarm message is sent the first preset number will also be dialed After successful setting the terminal returns 720 CONFIG OK to the mobile phone if the password is wrong 720 PASSWORD ER will be returned Note The default alarm mode of the terminal is 0 that is no alarm 730 Sampling interval Pieces of uploads User password The defaulted upload interval of this product is 0 meaning that the defaulted GPRS is closed The user may change the parameter according to actual demand
7. itude For example When 6660000 is sent the returned data format is as follows Lat latitude N S latitude value accurate to five decimal places Long longitude E W longitude value accurate to five decimal places Speed KM H accurate to two decimal places Direction direction of course accurate to two decimal places Date YYYY MM DD Time HH MM SS Greenwich time BS base station information FIX location status A V ID IMEI STATE information state Example of valid data Lat N22 6189 Long E113 6333 Speed 0 17 KM H Direction 62 58 Date 2008 06 17 Time 09 39 45 BS 27970eb3 FIX A ID 123456789000001 STATE SMS Query through mobile phone When you call the terminal with a mobile phone phone number preset number and hang up the phone after ringing 2 5 times the terminal will return a message about the latitude and longitude To use this function the calling number display function of the SIM card shall be subscribed 710 center number user password Description The center number setting instruction is set by the operator for the normal operation of the terminal under the center mode e g 710 1066512000 0000 After the instruction is executed the center number is set as 1066512000 After successful setting the terminal returns 710 CONFIG OK to the mobile phone if the password is wrong 710 PASSWORD ER will be returned 711 phone number 1 p
8. stalled close the shell tightly connect the wires and turn on the equipment GPS antenna Notice The motherboard indicators and the light slots of the shell shall be aligned with GPS antenna facing upwards For the most basic positioning function just connect to the vehicle power supply Product Characteristics e GPS vehicle location e GSM 850 900 1800 1900MHz e High sensitivity highly integrated GPS chip e Low energy consumption e Fast signal acquisition e Support single location and continuous tracking e Support the fence alarm e Support location information query through SMS and the Internet e Locate the user by telephone or through SMS Product Specifications GSM module GSM 850 950 18000 1900MHz GPS sensitivity 159dBm GPS center frequency L1 1575 42MHz GPS positioning accuracy 5 25m Speed accuracy 0 1 m s Time accuracy In sync with GPS Default data WGS 84 Hot start 1s Cold start 38 s Maximum altitude 18000 m Maximum speed 515 m s Acceleration of gravity lt 4g Operating temperature 20 65 C Humidity 5 95 Dimensions mm 50 45 21 Voltage 12V 24V Average standby current Less than 80MA LED Power supply work status indication Operating instructions of SMS positioning Send the message instruction 666 user password to the terminal and then the terminal will return a message about the latitude and long

1 User manual

Contents

Download Pdf Manuals

Related Search

Related Contents