LED MOTION ACTIVATED FLOOD LIGHT
Contents
1. Utilitech amp UT Design are registered trademarks of LF LLC All Rights Reserved N a x a p L K HR ea Laa TT ATTACH YOUR RECEIPT HERE Serial Number Purchase Date oze SRS0SR SSR aKT AAA Laa Ca LT ITEM 0611551 0611550 LED MOTION ACTIVATED FLOOD LIGHT MODEL SE1036 BP2 02LF0 U SE1036 WH3 02LF0 U Frangais p 10 Espanol p 19 Questions problems missing parts Before returning to your retailer call our customer service department at 1 866 994 4148 8 a m 6 p m EST Monday Thursday 8 a m 5 p m EST Friday AB14519 FUTILI Lowes com U PRO PACKAGE CONTENTS PARTS DESCRIPTION QUANTITY PARTS DESCRIPTION QUANTITY LED Head B Sensor Arm 1 D Wall Plate 1 HARDWARE CONTENTS Note Hardware shown actual size 6 i Machine Machine Silcone Screw Screw Wire Nut Cap Foam Gasket lt Qty 3 Long Not shown Qty 2 Qty 2 Mounting Strap Machine Qty 1 to size Not shown Screw Qty 1 to size Qty 1 Qty 1 SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble operate or install the product SAVE THESE INSTRUCTIONS IN A LOCATION CLOSE TO YOUR LIGHT FIXTURE SO YOU CAN REFER TO THEM AT A LATER TIME WARNING Shut off power at the circuit breaker or fuse panel before removing the old fixture or installing the new one e LED electronics can be damaged by electrostatic discharge2. ESD shock Before installation discharge yourself by touching a grounded bare metal surface to remove this hazard To avoid damage do not remove the clear lens over the LED module CAUTION e DO NOT USE THIS FIXTURE WITH A DIMMING CIRCUIT If you currently have dimmer controls you will need to remove them and replace them with regular electrical switches If you have a three way dimmer you will have to replace it with a regular three way switch If you are unfamiliar with electrical installations it is recommended you have a qualified electrician do your installation Lowes com A SAFETY INFORMATION IMPORTANT SAFETY INSTRUCTIONS Turn power OFF before installing or servicing Do NOT touch or install fixture while in contact with standing water Do NOT remove the protective LED lens Do NOT look directly at lighted LEDs for any length of time Do NOT leave bare wires exposed outside the wall canopy enclosure Electrical requirements 120 V AC 60 Hz 0 31A Minimum 90 supply conductors Suitable for wall or eave mounting onto recessed or round surface mounted electrical boxes rated for wet locations Not suitable for ground mount electrical boxes Do NOT allow the sensor head to touch the LED head housing Maintain at least 1 in spacing between the LED heads and the sensor head 9 For proper operation and protection against water damage the motion sensor adjustment controls MUST be facing downward 10 Do NOT mou
3. hat circuit breaker and or wall at night when motion delivered to the fixture switch power is on is detected 2 Another light source is 2 Turn off surrounding lights and or re aim causing the security light the sensor head to think it is daylight 3 Wiring inside electrical box 3 AFTER turning power off to the fixture came loose reconnect any loose wiring 8 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Security light comes 1 Dusk to dawn sensor is 1 Shine a flashlight onto the light sensor If the on during the day a shaded area and is security light turns off then the fixture is fooled into thinking it mounted in an area that does not allow enough is nighttime light to enter the sensor Relocate security light 2 Dusk to dawn sensor 2 If under warranty contact Customer Service is faulty Security light cycles ON 1 Dusk to dawn sensor is 1 Change position of light head aim light and OFF continuously sensing reflected light away from the reflecting surfaces from the security light 2 Put a small piece of black electrical tape over the Dusk to dawn sensor control 3 Relocate security light to a different location where it no longer causes reflected light Security light comes 1 Light is sensing motion 1 Make sure the sensor is not picking up moving on for no apparent in the detection zone objects such as bushes trees traffic water etc reason at night 2 Test the mot
4. ich is 1 to person or property or otherwise II incidental or consequential in nature III based upon theories of warranty contract negligence strict liability tort or otherwise or IV directly or indirectly related to the sale use or repair of the product This warranty gives you specific rights and you may also have other rights which vary from state to state Printed in China Utilitech amp UT Design are registered trademarks of LF LLC All Rights Reserved 2814INSSE1036 9 tits OD SS
5. iginal settings of the AUTO motion sensor mode At any point while in manual ON mode return to the AUTO motion sensor mode by toggling the wall light switch OFF and ON again within 2 seconds SECURITY LIGHT OPERATION SLIDE SWITCH WALL SWITCH SENSITIVITY Test Mode Test Turn on Any setting AUTO Motion Sensor 1 5 or 10 Minutes ON Any setting Mode Manual ON Mode 1 5 or 10 Minutes Toggle OFF and ON Any setting within 2 seconds Return to AUTO Motion 1 5 or 10 Minutes Toggle OFF and ON Any setting Sensor Mode within 2 seconds CARE AND MAINTENANCE e Periodically clean the fixture and diffuser using a mild non abrasive glass cleaner and soft cloth Do NOT use solvents or cleaners containing abrasive agents When cleaning the fixture make sure you have the power turned off and do not spray liquid cleaner directly onto any part of the fixture or LEDs TROUBLESHOOTING e Extreme hot or cold weather could affect the performance of the built in sensors that detect body heat Certain winter clothing can shield a person s body heat from the sensor during extreme cold weather During extreme hot weather the sensor may not be able to distinguish the difference between normal body temperatures and the surrounding high temperatures The sensor will begin working normally once weather conditions return to normal PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Light does not come on 1 No power is being 1 Check t
6. ion sensor by covering up the front curved lens with cardboard to block the view If the light turns off then something in the detection zone is triggering the sensor Reposition the motion sensor or change the sensitivity distance of the sensor WARRANTY The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of 5 years from the date of original purchase by the consumer We will repair or replace at our option the unit in the original color and style if available or in a similar color and style if the original item has been discontinued without charge The manufacturer warrants the LEDs for 5 years providing the fixture is not used in a commercial application where it is on 24 hours per day but is used in a residential environment for 3 5 hours per day Defective units must be properly packed and returned to the manufacturer with a letter of explanation and your original purchase receipt showing date of purchase Call 1 866 994 4148 to obtain a return authorization number and an address where to ship your defective product Note No C O D shipments will be accepted The liability of the manufacturer is in any case limited to replacement of the defective light fixture product The manufacturer will not be liable for any other loss damage or injury which is caused by the product This limitation upon the liability of the manufacturer includes any loss damage or injury wh
7. ned to the ON position and check that your light is functioning properly If the light is functioning properly fit the silicone cap FF into the mounting screw opening to prevent water seepage into the housing Hardware Used Silicone Cap C x 1 INSTALLATION INSTRUCTIONS FOR RECESSED ELECTRICAL BOXES With power to the electrical box turned off remove the old fixture If the old fixture is attached to an electrical box that has more than two wire leads mark the wires to keep track of the correct ones to use Remove any mounting hardware that was used to mount the old fixture 1 Pull the supply wires out of the electrical box Using the machine screws AA or BB that fit the electrical box secure the mounting strap CC to the electrical box making sure that the side marked FRONT is facing out Hardware Used x2 e Ws K BB A Machine Screws cc Mounting Strap gt x4 2 For safety and proper installation the fixture must be properly grounded If unfamiliar with the methods of properly grounding the fixture consult with a qualified electrician A green copper ground wire is pre attached to the fixture If the electrical box is made of plastic and or has a green or bare copper grounding wire inside the fixture grounding wire and the electrical box ground wire should be connected together using one of the small wire nuts included If the electrical box is made of metal and alread
8. nsor arm 4 Each light head can be adjusted at the sensor arm and base of the fixture s Oc SITTIN TEST 1510 A lt K Vsiq S TEST 1 OPERATING INSTRUCTIONS 5 Once the fixture has been tested for proper operation and sensitivity move the switch to the 1 5 or 10 position Each of these positions allows the fixture to go into AUTO motion sensor mode Each of these settings indicates the time frame that the light SP will remain on after detecting motion If set for the 1 Sa setting the lights will come on for 1 minute after gE detecting motion and then will go off and return to the Term TEST 1 510 AUTO motion sensor mode When set for 5 the lights will remain on for 5 minutes after detecting motion If yz ao K TIMER ZO set for 10 the lights will remain on for 10 minutes 10 Minutes Oo Aion Gus c SN TEST 1 R 10 W after detecting motion If motion is continuously Were TESTT 510 detected during the lights ON cycle the lights will remain on until the motion ceases 6 To be able to manually turn on the security light from inside your home toggle the wall light switch OFF and ON within 2 seconds The security light will turn on and stay on for approximately 8 hours or until the dusk to dawn sensor detects light in the morning Once the dusk to dawn sensor detects light the manual ON mode will automatically go back to its or
9. nt below 5 ft 11 Do not mount near other light sources that can compromise the dusk to dawn sensor 12 This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation o JW EMM A PREPARATION Before beginning installation of product make sure all parts are present Compare parts with package contents list and hardware contents list If any part is missing or damaged do not attempt to install the product Estimated Assembly Time 45 minutes Tools Required for Assembly not included Phillips screwdriver and silicone adhesive caulking Select the installation location carefully Do not install in areas having pedestrian or motorized traffic pools or bodies of water or trees bushes that move in the wind All of these may trigger the motion sensor security light and may be disruptive to the intended operation of the light Do NOT install near other sources of light The other light sources can fool the dusk to dawn sensor into thinking it is daylight INSTALLATION INSTRUCTIONS FOR ROUND SURFACE MOUNT ELECTRICAL BOXES With power to the electrical box turned off remove the old fixture If the old fixture is attached to an electrical box that has more than two wire leads mark the wires to keep track of the correct ones to use Remo
10. rom the electrical box to the fixture wire leads using the wire nuts DD The black lead from the fixture is connected to the black supply lead and the white fixture lead is connected to the white supply lead Tighten the wire nuts properly to prevent them from coming loose If needed use electrical tape to secure the wire nuts onto the wire leads Push the excess wires back into the electrical box Hardware Used D Wire Nut L x3 4 Position the wall plate over the mounting strap so the center hole of the wall plate aligns with the center hole in the mounting strap While holding the wall plate in place put the long machine screw EE through the center hole of the wall plate and mounting strap Tighten the screw properly to secure the wall plate onto the electrical box NOTE Make sure the gasket GG properly seals the gap between the wall plate and the electrical box to prevent water seepage into the electrical box Hardware Used EE Long Machine Screw 5 If eave mounting the fixture position the sensor head with the adjustment controls and drain holes facing downward to prevent water damage The position of the sensor head should not exceed 45 degrees from horizontal Lowes com INSTALLATION INSTRUCTIONS FOR ROUND SURFACE MOUNT ELECTRICAL BOXES 6 Restore power to the electrical box at the circuit breaker or fuse panel Make sure the wall switch that controls the electrical box for your security light is retur
11. t stops it will turn off in 5 seconds 2 There is also a rotary knob on the bottom of the motion sensor labeled SENSITIVITY Rotating this knob clockwise raises the sensitivity of the motion sensor for up to 60 ft of distance Rotating the knob counterclockwise lowers the sensitivity down to as close as 5 ft It may be necessary to adjust the SENSITIVITY knob several times until you find the proper setting for your particular installation NOTE The higher sensitivity level for longer distances up to 60 ft increases the likelihood of false triggering For maximum range performance allow the fixture to operate in any mode with power for at least 48 hours 3 The 180 coverage of the motion sensor is measured side to side Therefore the sensor will better detect motion across the field of view side to side rather than motion coming straight at the sensor in and out Adjust the motion sensor head so that it sees motion moving across the coverage area Make sure the sensor head is positioned with the front lens facing slightly downward 5 15 angle to prevent water accumulation on the sensor head Do not aim the motion sensor at a body of water bushes or plants that may move in the wind pedestrian traffic moving cars etc as this will trigger the motion sensor NOTE If the sensor arm becomes loose it will not hold the sensor head at the proper angle Readjust the sensor head and tighten the joint screw on the se
12. ty light is returned to the ON position and check that your light is functioning properly If the light is functioning properly use silicone adhesive caulking not included to caulk the gap between the wall plate and the mounting surface to prevent water seepage into the electrical enclosure 6 Fit the silicone cap FF into the mounting screw opening to prevent water seepage into the housing Hardware Used Silicone Cap x1 ma UTILI 6 Lowes com OPERATING INSTRUCTIONS The fixture comes with a 180 motion sensor and a built in dusk to dawn sensor The dusk to dawn sensor disables the motion detector during daylight hours and only allows the motion sensor to activate the light after dark The security light will not activate during daylight hours regardless of whether it sees motion or not 1 The slide switch on the bottom surface of the motion sensor has four settings TEST 1 5 10 In the TEST position the motion sensor will turn the lights on for 40 seconds after power is applied to the fixture To test your fixture switch the wall switch that controls power to the fixture to the ON position The lights will come on for 40 seconds regardless of whether there is motion or not and regardless of whether it is day or night Leave the slide switch in the TEST setting and adjust the sensitivity by crossing in the path of the sensor The light will come on only if it senses movement Once movemen
13. ve any mounting hardware that was used to mount the old fixture 1 Pull the supply wires out of the electrical box Using the machine screws AA or BB that fit the electrical box secure the mounting strap CC to the electrical box making sure that the side marked FRONT is facing out Hardware Used x2 Machine Screws m eD ZN cc Mounting Strap gt x1 U UTILI Lowes com PRO INSTALLATION INSTRUCTIONS FOR ROUND SURFACE MOUNT ELECTRICAL BOXES 2 Remove the protective paper barrier from the adhesive face of the foam gasket GG Trace the supply wires through the openings in the gasket and adhere the gasket to the mounting strap and outer edge of the round surface mount electrical box Hardware Used GG Foam Gasket x1 3 For safety and proper installation the fixture must be properly grounded If unfamiliar with the methods of properly grounding the fixture consult with a qualified electrician A green copper ground wire is pre attached to the fixture If the electrical box is made of plastic and or has a green or bare copper grounding wire inside the fixture grounding wire and the electrical box ground wire should be connected together using one of the small wire nuts included If the electrical box is made of metal and already grounded secure the bare end of the fixture ground wire to the mounting strap marked GND using the green grounding screw Connect the supply leads f
14. y grounded secure the bare end of the fixture ground wire to the mounting strap marked GND using the green grounding screw Connect the supply leads from the electrical box to the fixture wire leads using the wire nuts DD The black lead from the fixture is connected to the black supply lead and the white fixture lead is connected to the white supply lead Tighten the wire nuts properly to prevent them from coming loose If needed use electrical tape to secure the wire nuts onto the wire leads Push the excess wires back into the electrical box Hardware Used DD Wire Nut x3 U UTILI PRO Lowes com INSTALLATION INSTRUCTIONS FOR RECESSED ELECTRICAL BOXES 3 Position the wall plate over the mounting strap so the center hole of the wall plate aligns with the center hole in the mounting strap While holding the wall plate place the long machine screw EE through the center hole of the wall plate and mounting strap Tighten the screw properly to secure the wall plate onto the mounting surface Hardware Used B Long Machine Screw 4 If eave mounting the fixture position the sensor head with the adjustment controls and drain holes facing downward to prevent water damage The position of the sensor head should not exceed 45 degrees from horizontal 5 Restore power to the electrical box at the circuit breaker or fuse panel Make sure the wall switch that controls the electrical box for your securi
Download Pdf Manuals
Related Search