Magic Box Wide Beam User Manual
Contents
1. INN WSC VVLIL2E Ss SS ZA AL10 Series User Manual OMNISISTEM www omnisistem com Introduction Specifications Thank you for purchasing Magic Box Wide Beam Magic Box Wide Beam is a 1 channel DMX laser can be controlled via a standard DMX controller It is a Product Name Magic Box Wide Beam lightweight mini intelligent fixture and is an ideal product for discos clubs exhibitions ModelNo and any place that need visionary effect For safe operation read this manual pose ALT10096 before powering or installing the fixture follow the safety precautions listed below and 4 9 observe all warnings printed in this manual and on the fixture Laser Color Green Safety Precautions gt S AC 120V 50 60HZ m Do not spill liquids into or onto your unit If this ever happens disconnect the main Classification 3R power immediately Do not connect this unit to any dimmer pack ze WE Tren m Always disconnect from main power before making any type of connection Size mm 0 x W280 x m Be sure to locate this unit in a place with adequate ventilation at least 15 cm from a Fuse 20mmx2A wall and mount this unit in safe and stable matter m To prevent fire or shock hazard do not expose this unit to a high temperature or 15 mid high humidity area Please unplug unit when not in use Operating temperature 180 250 m Always keep combustible materials away from the fixture m Class 3B laser should be mounted at or above 3 meters heigh2. Out from the first unit to In on the second Out from the second to In on the third and so on Auto mode E To set the master Set DIP switch pin 11 and 10 to ON other pins to OFF a To set the slaves Set pin 1 to ON other pins to OFF Sound Active mode a To set the master Set DIP switch pin 11 to ON other pins to OFF MI To set the slaves Set pin 1 to ON other pins to OFF DMX Operation DMX operation gives the user freedom to create his her own programs tailored to their own individual needs To run this unit in DMX mode connect the unit to any standard DMX controller via XLR connectors Please consult DMX controller manual to determine address DMX Signal Levels DMX 512 LEVEL 0 255 Laser effect Control Sound Active Effect45 10 14 Effect2 C There are 45 effects preset between value5 to 229 Select them EE SKI changing signal level as above introduction Operating Modes Cont Function Selection Chart orewnosowm mino ee eTe e e e eTe ar orr oor orr or forr orrore souno none ar orr or orrore orr ofore orelon gt 7 muro wone SET SOUND AUTO MODE o DMX MASTER Va DMX SLAVE A Not Used Trouble Shooting E If there is no light from the unit please check the main power supply and fuse E If unit does not respond to DMX please check the DMX cables are connected properly and are wired correctly a If unit does not response to the music please adjust the sound a
3. ctive sensitivity level by Sensitivity Adjustment Knob ma If the beam is fuzzy please refer to cleaning section to clean the mirror first hg If problems cannot be solved please contact your dealer for service Fuse Replacement Always disconnect from main power supply before attempting to replace the fuse Remove the old fuse from the holder and replace with the exact same type fuse Replacement with anything other than the specified part may damage your unit Control Panel Introduction P Bik 6 amp Key control Power Cord Connection Fuse Power Switch Sensitivity Adjustment Knob Microphone DMX In amp Out DIP Switch Pin lnterlock connector Key control
4. t Project Class 3B laser light above eye level Do not project Class 3B Laser light on specular material m he entrance to area where Class3B laser is used should be posted with appropriate warning signs m This unit is intended for indoor use Use of this unit outdoors voids all warranties m Always refer service to a qualified technician Never look directly into laser beam m Occasional breaks are necessary to prevent breakdowns m Caution Use of controls or adjustments or performance of procedures other than as specified herein may result in hazardous radiation exposure Set Up Unpacking Magic Box Wide Beam comes with 2 keys 1 hanging bracket 2 clamp levers 2 washers 1 power cord and 1 user manual Unpack carefully and be sure that no damage has occurred during shipping If there is anything missing or appear to be damaged please contact your dealer Power Connection Be sure the source voliage in your area matches the required voltage for your Magic Box Wide Beam before plugging your unit in Incorrect voltage selection will detrimentally affect the operation of this product DMX Cable Connection Magic Box Wide Beam is a one channel DMX fixture that can be operated with universal DMX controller This unit and DMX controller require a standard 3 pin XLR connector for data input and data output Installation Mounting Magic Box Wide Beam should be properly mounted by using a suitable hanging clamp and safety cable Use in a well ven
5. tilated area Be sure no ventilation slots are blocked Safety Label Position Bottom Identification label Certification label Warning label Laser aperture amp aperture label Cleaning Caution Shut off the main power prior to cleaning unit Cleaning mirrors BB Use a cotton swab and rubbing alcohol to clean the internal laser mirrors i Remember to twirl slowly and press gently Applying to much pressure can break the mirrors a Cleaning frequency depends on the environment in which the fixture operates Cleaning case Use a soft cloth and normal glass cleaner to clean the casing Be sure to dry all parts before plugging the unit back in Operating Modes Note User must turn on key control to emit laser W Stand Alone Operation Auto Sound Active Mode Auto mode E The unit runs built in program to change effects automatically Set DIP switch pin 10 to ON other pins to OFF to run Auto mode Sound Active mode m This unit has built in program that will react to sound and music under Sound Active mode Set all DIP switch pins to OFF to run Sound Active mode Master Slave Operation Auto Sound Active Mode This mode allows user to link up to 32 units to run the Master Slave operation In the Master Slave operation one unit will act as the controlling unit and the others will react to the controlling unit Daisy chain your units via the standard XLR microphone cables in the following configuration
Download Pdf Manuals
Related Search