USER MANUAL OF PROGRAM CARD
Contents
1. Manual of Program Card USER MANUAL OF PROGRAM CARD Thank you for purchasing the program card for the brushless electronic speed controller ESC With this equipment you can set the ESC very easily The program card is pocket sized and has a very friendly user interface SPECIFICATION 1 SIZE 92mm 52mm 6mm 2 WEIGHT 26g as jeu is FRONT PANEL 1 Use up down button to select the programmable item use left right button to select the options of each programmable item 2 Brake When Brake is ON the motor will stop immediately when the throttle stick is moved to the lowest position 3 Low Voltage Protection Mode Cut off Type When Soft Cut is selected the ESC will gradually reduce the output power When Cut Off is selected the ESC will immediately shut off the output power 4 Low Voltage Protection Threshold Cut off Voltage Please check the user manual of the ESC to get detail information about this item 5 Music Lipo Cells The 4 LEDs have different meanings for the normal voltage ESC works with 2S to 6S Lipo or the high voltage ESC works with more than 6S Lipo For ESC without a postfix character of HV for example Flyfun 60A 4 LEDs have 16 possible states representing 16 rhythms for ESC The ESC will play the music when it is started Please refer to the Table 1 in the next page For ESC with a postfix character of HV for example Fl2. an individual data cable that is a very short trio wire just nearby the Rx cable please disconnect the Rx cable of the ESC from your receiver and then connect the individual data cable to the program card at the position marked with BEC 3 Connect the receiver battery pack 4 8 6V to the program card at the top right corner position marked with Batt 4 Connect the main battery pack to the ESC 5 The LEDs on the program card will light to show the current programmable values of the ESC NOTE2 The sequence of Step 2 step 3 and Step 4 cannot be reversed Otherwise the program card cannot work properly NOTE3 Don t use a battery pack higher than 6V to supply the program card OPERATION Click the up down button to select the programmable item the corresponding LED will blink Then click the left right button to select the options of this item the flashing LED shows the value you are just selecting Finally click the OK button the blue LED will blink which means the new settings are being transmitted to the ESC When the data transmission is finished the blue LED stops blinking it means the new settings are accepted and stored in the ESC Manual of Program Card MUSIC LIST Table 1 Music list No Sa ee ere ee Pro e o osenemsepamoman o o o osmu e o o o o oneen repo fo fe o owen o o e o o eorom e ole fo o ssn ci r o o e o remera cma e o o o o uessa o e o
3. o o mew o e o o o er n e o e o memar e o e o rrmoavuronemmn s e e o olm u e o o o oansein s e o o o Pesan e e e o olimme LED is lighting MUSIC HW SM801DUL 20130618 LI PO BATTERY CELLS AMOUNT LIST Table 2 Lipo cells amount list LED is lighting LED Li Poly Cells Number A po fo fe mwa ol o o e anwar Po fo fe 0 mwee ofo e ewe e e o o we Pe fe ole wm Pe fe fe o wm Te fe e fase We strongly suggest manually setting the cells amount of your Lipo battery pack Please be careful to use Auto detect options DECLARATION This program card is ONLY suitable for the ESC made by the same manufacturer Please ask your retailer for detail product information
4. yfun 100A HV 4 LEDs represent the number of Lipo battery cells amount Please refer to the Table 2 in the next page WIRING SEQUENCE A When you are using an ESC with a built in BEC Battery Elimination Circuit 1 Disconnect the main battery pack from the ESC 2 For ESC with a built in BEC please disconnect the Rx cable trio wires of the ESC from your receiver and then connect it to the program card at the top right corner position marked with BEC A att BEC HW SM801DUL 20130618 3 Connect the main battery pack to the ESC 4 The LEDs on the program card will light to show the current programmable values of the ESC NOTE1 The sequence of Step 2 and Step 3 cannot be reversed Otherwise the program card cannot work properly B When you are using an ESC without a built in BEC If the ESC is marked with OPTO For example Flyfun 80A OPTO that means this ESC hasn t a built in BEC then you must use an additional battery pack 4 8 6V to supply the program card and usually a receiver battery pack is a good choice By the way most of the high voltage ESC works up to 10 or 12S Lipo hasn t built in BEC 1 Disconnect the main battery pack from the ESC 2 Disconnect the Rx cable trio wires of the ESC from your receiver and then connect it to the program card at the top right corner position marked with BEC For high voltage ESC with a postfix character of HV if it has
Download Pdf Manuals
Related Search