AVM301 MEGAPIXEL NETWORK CAMERA SERIES
Contents
1. LAN Port WAN Port Router gt AVM301 Modem E gt Devices connected with a RJ45 network cable Step2 Open IPScan exe 4 to search your AVM301 The default IP address of AVM301 is 192 168 1 10 If you connect two or more AVM301 to the same router IPScan will list many AVM301 with different IP addresses after searching To know which AVM301 you re configuring you may identify each with its unique MAC address Note The MAC address can be found on the sticker at the rear panel of AVM301 Search IP Port Type Mac 192 168 1 10 88 IP CAMERA FIX 00 De 53 1d 6f f1 A Confiqure 192 168 2 11 88 IP CAMERA FIX 00 0e 53 1d 6f e8 Upgrade ServerIP 192 168 2 25 DNS 168 05 1 1 Mac Address 00 0e 53 10 6611 NetMask 255 255 255 0 GateWay 192 168 2 1 Step3 Select the IP address you want to configure and click Configure to show the IP setting page and change the IP address gateway and port number For example the IP address of your router is 192 168 2 1 Then in this step you need to change the IP address to 192 168 2 xx xx means any value from 2 50 and change the gateway to 192 168 2 1 the same as the IP address of your router Then change the port number to any value other than 88 if needed Note Make sure the IP address you change is not used by other devices connected to the same router Step4 Enter the user n2. EEE Username office Username admin AA AAA AA A ooo LL a Password seeeeee Password eesesses Confinm ff STP Confirm Sirera Password Macia Password CA User Lavel SUPERVISOR user Level SUPERVISOR B Life Time INFINITE D Life Time INFINITE wa av Account List Save Account List 11 2 BEFORE YOU START TO USE After you finish network configurations some camera configurations in Config are recommended to complete for the camera to work properly Below assumes you re using Internet Explorer to access the camera Note For iPhone users please access the camera and select on the top right corner of the live view to enter the configuration page 2 1 Video Adjustment When you ve accessed the camera successfully for the first time its recommended to adjust the video images if needed To adjust the clearness of the video rotate the camera lens manually as shown in Figure 1 To slightly adjust the color of the video in the live page of your web browser click Config on the top right side of the browser to open the configuration page Then click Camera gt Color to adjust the brightness contrast hue saturation of the video images as shown in Figure 2 i z Color Configuration P JO ROTATE Brightness Contrast Hue CO Oo O Saturation 4 Reset Default w Reload Figure 1 Figure 2 12 APPENDIX 1 CHANGE IP ADDR
3. AVM301 MEGAPIXEL NETWORK CAMERA SERIES ADVANCED NETWORK SETUP Please read instructions thoroughly before operation and retain it for future reference m301_network_V0 9 IMPORTANT SAFEGUARD All lead free products offered by the company comply with the requirements of the RoHS European law on the Restriction of Hazardous Substances RoHS directive which means conform our manufacture processes and products are strictly lead free and without the hazardous substances cited in the directive The crossed out wheeled bin mark symbolizes that within the European Union the product must be collected separately at the product end of life This applies to your product and any peripherals marked with this symbol Do not dispose of these products as unsorted municipal waste Contact your local dealer for procedures for recycling this equipment E This apparatus is manufactured to comply with the radio interference requirements Federal Communications Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital service pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation Any changes or modifications made to this equipment may void the user s authority to operate this equipment This equipment generates uses and can radiate radio frequency energy If not installed
4. default in System Name c In Hostname keep the default value i e the MAC address of this camera Then note down the whole address of the camera for example MACO000e531d6ff1 ddns eagleeyes tw d Optional Enter your email address to receive messages from the DDNS server Note Please at least use the default address to access your network camera remotely once This is to ensure our DDNS server has your camera registered Then you may change the host name to a more meaningful name to memorize later here e Click Save to return to the network setting page Then click Next Step6 Check if the changes you ve made are correct and click Save to complete Wizard f de Step4 Network Step5 Apply lt Account gt lt Time gt Username admin e hange Password 7 E lt Network gt IP Type DHCP Port 80 DNS1 168 95 1 1 DNS 139 175 55 244 lt DDNS gt Disable System Name default Hostname MACODO0E5S320E73E E Mail manager tech com Ea Check your connection Step1 Disconnect your camera and your laptop PC and connect them to Internet separately Note If you changed the IP address of your laptop PC for LAN connection remember to restore it back for Internet access to work properly Step2 Enter the host name you just noted down and the port number in the URL address box of the web browser and see if you can access the login page of the camera successfully The fo
5. gt You have downloaded IPScan exe in your laptop PC Note Please download IPScan exe from www surveillance download com user m301 swf Step1 Connect your laptop PC to the wireless network with AVM301 connected Laptop or PC Ms N es E A LAN Port Wireless Router o A Modem AVM301 3 Devices connected with a RJ45 network cable a Devices connected wirelessly Step2 Open IPScan exe amp to search your AVM301 The default IP address of AVM301 is 192 168 1 10 If you connect two or more AVM301 to the wireless router IPScan will list many AVM301 with different IP addresses after searching To know which AVM301 you re configuring you may identify each with its unique MAC address Note The MAC address can be found on the sticker at the rear panel of AVM301 Search IP Port Type Mac 192 168 1 10 88 IP CAMERA FIX 00 0e 53 1d 6f f1 Configure 192 168 2 11 88 IP CAMERA FIX 00 0e 53 1d 6f e8 Upgrade Server IP 192 168 2 23 MAC Address 00 0e 53 1d 6f f1 NetMask 255 255 255 0 GateWay 192 168 2 1 Step3 Select the IP address you want to configure and click Configure to show the IP setting page and change the IP address gateway and port number For example the IP address of your router is 192 168 2 1 Then in this step you need to change the IP address to 192 168 2 xx
6. A2 1 Prerequisites Before installing EagleEyes to your mobile phone for remote surveillance make sure you have checked the following v Your mobile platform is iPhone iPad Android v Mobile Internet services are subscribed and available to use for your mobile phone Note You might be charged for Internet access via wireless or 3G networks For the Internet access rate details please check with your local network operator or service provider v You have noted down the IP address port number user name and password used to access your network camera from Internet A2 2 Where to download Connect to www eagleeyescctv com from your mobile phone and sign in Note Please DO NOT try to download EagleEyes from your computer Then select Software and the mobile platform of your phone to download EagleEyes to your phone E For Android amp iPad select the download link from the website to start downloading E For iPhone two versions of EagleEyes are available EagleEyes Plus US 4 99 and EagleEyes Lite Free Select the version you want and you ll be directed to App Store to download the application Note You can also find EagleEyes on App Store from your iPhone Go to App Store and select Search Enter the keyword eagleeyes to find and download the version you want iPhone BlackBerry Symbian Win Mobile lownload iPhone EagleEyes Plus US 4 99 More ower of mobile surve
7. AVM301 and enable this rule Take D Link router as an example Go to ADVANCED gt PORT FORWARDING DIR 635 SETUP ADVANCED TOOLS STATUS SUPPORT Helpful Hints PORT FORWARDING This option is used to open multiple ports or a range of ports in your router and redirect data Check the Application through those ports to a single PC on your network This feature allows you to enter ports in various formats including Port Ranges 100 150 Individual Ports 80 68 888 or Mixed 1020 5000 689 This option is only applicable to the INTERNET session predefined applications z If you select one of the NETWORK FILTER Don t Save Settings predefined applications click the arrow button ACCESS CONTROL next to the drop down 24 PORT FORWARDING RULES menu to fill out the corresponding field INBOUND FILTER You can select a Schedule computer from the list Always of DHCP clients in the Computer Name drop Inbound Filter down menu or you Name my home IP Address FIREWALL SETTINGS Application Name iv Es ROUTING ADVANCED WIRELESS 192 168 2 25 Computer Name IV Alowar v NA AE IP address of the LAN WISH Schedule computer to which you rey payee o Application Name Always would like to open the e IP Address UDP Inbound Fiter iS q 0 0 0 0 Computer Name v Allow All Y ADVANCED NETWORK Select a schedule for
8. of the http 60 248 97 4 80 or https 60 248 97 4 59207 BM Wizard Config amp admin Logout Disable IP CAMERA Fixed AVN806 000E5320E73E O Disable Your IP C router using the following URL LAN 1P Address 80 59207 If set to blank or 0 a port number wil be set automatically upon enable Check your connection Step1 Open your web browser e g Internet Explorer Step2 Enter the IP address or host name you just noted down and the port number in the URL address box of the web browser and see if you can access the login page of the camera successfully The format is http ipaddress portnum or http hostname portnum 1 5 Modem Hub Modem You may use your laptop PC to complete the network configuration of the camera Before configuring this camera on your laptop PC make sure gt Your Windows operating system is Windows 7 Vista or XP gt You have changed the IP address of your laptop PC to 192 168 1 xxx where xxx could be 0 255 except 10 Note To know how to change the IP address of your laptop PC please refer to APPENDIX 1 CHANGE IP ADDRESS OF YOUR LAPTOP PC at page 13 E Stepi LAN Connection fer WAN Port Hub Optional AVN801 Modem Devices connected with a RJ45 network cable Step1 Disconnect your laptop PC from the hub or modem and connect it to this camera with a network cable Note Make sure the IP address of y
9. successfully m f yes your network setup is successfully E f no go to Step3 Step3 Switch your network mode to wireless mode on iPhone or iPad Step4 Start EagleEyes and add a new connection with the IP address e g 192 168 2 25 and the port number e g 88 Then try this connection and see if you can access the camera successfully m f yes go for port forwarding setting as instructed in APPENDIX 3 CONFIGURE PORT FORWARDING at page 17 EH f no return to Step1 in 1 2 2 Configuring on iPhone iPad and re configure the network again 1 4 Router Modem You may use your laptop PC to complete the network configuration of the camera Before configuring this camera on your laptop PC make sure gt Your Windows operating system is Windows 7 Vista or XP gt Recommended Your router supports UPnP and this function is enabled Note If your wireless router doesn t support UPnP you need to additionally access your router for port forwarding For details please refer to APPENDIX 3 CONFIGURE PORT FORWARDING at page 17 gt You have noted down the IP address of your router Note For details please refer to the user manual of your router or check with your installer gt You have downloaded IPScan exe in your laptop PC Note Please download IPScan exe from www surveillance download com user m301 swf Step1 Connect your laptop PC to the router Laptop or PC t E benno
10. to the next step Step4 In Network configure the network setting of your camera based on the network type you re using There re three types Static IP PPPOE and DHCP For Static IP a Enter the information of Server IP Gateway and Net Mask obtained from your ISP Internet Service Provider b Enter the port number The valid number ranges from 1 to 9999 The default value is 88 c Click Save to save your network configurations and log out d Disconnect your camera and your PC and connect them to Internet separately Then enter the IP address you just note down in the URL address box of the web browser and see if you can access the camera successfully For PPPOE a Enter the user name and password obtained from your ISP and click Save b Continue the DDNS setting as instructed in Step5 For DHCP a Before selecting this option you need to finish the DHCP router settings first b Get a router and connect it to the Internet via your PC with Static IP or PPPoE setting There are different setting methods for different routers Please refer to their respective user manuals c Continue the DDNS setting as instructed in Stepb Step5 Optional Click DDNS 44 0018 to continue setting for PPPOE and DHCP DDNS DDNS Enable 0 Disable System Name default Y Hostname MACOD0Des31d6ft1 ddns eagleeyes tw E Mail manager tech com tw a Enable DDNS b Select
11. to your wireless router router hub modem with a network cable and power it on Note Check LAN status indicator is always on not blinking If it s blinking check your RJ45 network cable and ensure it s not disconnected or defect lf you re using m Wireless router modem please refer to 1 3 Wireless Router Modem m Router modem please refer to 1 4 Router Modem E Modem or modem hub please refer to 1 5 Modem Hub Modem For your account safety its recommended to change the default account setting For details please refer to 1 6 Change Default Account at page 11 1 3 Wireless Router Modem You may use your laptop PC or your iPhone iPad to complete the network configuration of the camera 1 3 1 Configure on Laptop PC Before configuring this camera on your laptop PC make sure gt Your Windows operating system is Windows 7 Vista or XP gt Recommended Your wireless router supports UPnP and this function is enabled If your wireless router doesn t support UPnP you need to additionally access your router for port Note forwarding For details please refer to APPENDIX 3 CONFIGURE PORT FORWARDING at page 17 You have noted down the IP address of your router and the assigned IP address es and port s of other devices connected to the same router Note For details please refer to the user manual of your wireless router or check with your installer
12. 5 255 0 planexuser a O SYSTEM a DNS 192 168 2 2 TecomGuest a gt Search Domains Y WLANO3 az Client ID Note This address will be needed when you want to access your router for port forwarding later Step1 Connect your iPhone to the wireless router which has AVM301 connected iPhone or iPad a LAN Port Wireless 5 Router Y AVM301 Devices connected with a RJ45 network cable 1 Devices connected wirelessly step2 Open EagleEyes on your iPhone or iPad In the address book click to add new device Then select Local Network Search to search your network camera You ll see an IP address assigned by your router Note If you can t find AVM301 make sure your LAN status indicator is always on and search again after 3 minutes lf you connect two or more AVM301 to the wireless router you ll see many AVM301 with different IP addresses after searching To know which AVM301 you re configuring you may identify each with its unique MAC address Note The MAC address can be found on the sticker at the rear panel of AVM301 lh PRIM 7 F4F6 18 O 98 Ga ah PRM S FF6827 O 96 Ga 192 168 2 197 Port 60 IPGAM FIXED 00 08 53 10 28 2b Username Password IP add ress assigned to the camera by your router Get Type Unknown Optional Audio OFF CH1 6 Quality BEST A Step3 Select the IP address you want to configure to show the IP address setting page IP Ad
13. ESS OF YOUR LAPTOP PC For LAN connection with this network camera you need to change the IP address of your laptop PC to 192 168 1 xxx 1 255 except 10 first Note Before changing the IP address make sure you note down the original IP address setting of your laptop PC You need to restore the IP address setting when you complete the network configuration of this camera For Windows XP users a Select start gt Control Panel gt Network and Internet Connections gt Network Connections If you re in Category View e Control Panel Pick a category Ge Switch to Classic View EA EE Appearance and Themes 20 Printers and Other Hardware ue gt h Windows Update 7 4 Help and Support rm Network and Internet Connections oi User Accounts Othar Control Panel gt Options a MEL addorRem Programs Al Date Time Language and Regional i i Options Network and Internet Connections See Also bility Options e os im 7 va Performance and Maintenance IU Security Center oan Network and Internet Connections See Also L a GD My Network Places a Printers and Other Hardware 49 Remote Desktop Ls Phone and Modem Options Pick a task El Set up or change your Internet connection E Create a connection to the network at your workplace Troubleshooters gt Set up or change your home or small office network Z Home or Small Office Network Connections Netwo
14. Name lt q TCP Schedule when the rule will be lt lt Application Name Y Always f English v g IP Address UDP Inbound Filter 0 0 0 0 lt lt Computer Name iv Allow All Y schedules go to the IP Address The IP address of AVM301 such as 192 168 2 176 Ports to Open The port number you set for AVM301 17 APPENDIX 4 Q amp A For more details about EagleEyes Q amp A please visit our official website www eagleeyescctv com supp QnA aspx Answer Question cant connect to AVN80X with 3G network from my iPhone iPad but it works with my wireless network Why My live images are not fluent Why The detection range of the built in human detection sensor seems too short and the sensor is not sensitive enough Did do anything wrong on installation The live video keeps flickering Why Your network configuration is not yet completed Please set port forwarding as instructed in APPENDIX 5 CONFIGURE PORT FORWARDING Image fluency could be affected by the local network upload bandwidth router efficiency client network download bandwidth complexity of live view and more Recommended To have the best image fluency select QVGA to have the best image quality select SXVGA to have normal image fluency and quality select VGA The human detection sensor might be influenced by the temperature of ambient environment and human beings and the applicable working temperat
15. ame and password of this camera to confirm the change and exit IPScan The default user name and password are both admin Step5 Open the web browser such as Internet Explorer on your laptop PC and enter the IP address you just set on the URL column to access this camera In the login page enter the user name password and security code to access Note Please skip the wizard Step6 Go to Config gt DDNS and enable the DDNS service Wizard Config amp admin Logout E Live View amp 2 DDNS E Config 4 DDNS DDNS Configuration DDNS Enable Disable System Name default v Hostname MACOO0ES320E73E ddns eagleeyes tw E Mail E f your router supports UPnP please proceed Step7 E f your router doesn t support UPnP click Save and access your router for port forwarding as instructed in APPENDIX 3 CONFIGURE PORT FORWARDING at page 17 Step7 Go to UPnP and enable the UPnP service Then enable Port Mapping and click Save to start port mapping When the configurations are saved successfully you ll see a message indicating the IP address and port number assigned to your device Note down the IP address and port number and log out the camera UPnP UPnP Configuration UPnP Friendly Name Port Mapping Configuration Port Mapping Por tono 9 Enable Router IP HTTP Port HTTPS Port amera is accessible from the other side
16. anage network connections If you re in Category View e a SE Network and Internet Network and Sharing Center vw gt fl Search A kopen Network and Sharing Center View computers and devices View full map Connect to a network Set up a connection or network A Bye bedi 2 i Manage network conns Hons 3 a GEMINI Multiple networks Internet Diagnose and air This computer Manage network connections is Access Local and Internet Connection Local Area Connection 2 View status i Name Status Device Name Connectivity Network Category Owner LAN or High Speed Internet 3 A la Local rea Connection ie ie Network cable unplugged NVIDIA nForce Networking Note If your local area connection is not enabled please also enable it c In the Networking tab select Internet Protocol Version 4 TCP IPv4 and select Properties d In the General tab select Use the following IP address and set the IP address as described below Note It s recommended to note down the current settings first and then change as instructed It s helpful when you need to restore the PC network settings for connecting to Internet later SI Internet Protocol Version 4 TCP 1Pv4 Properties e x General You can get IP settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator
17. and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures gt Reorient or relocate the receiving antenna gt Increase the separation between the equipment and receiver gt Connect the equipment into an outlet on a circuit different from that to which the receiver is connected gt Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device mat not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation FCC Caution gt Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment gt All external cables connecting to this basic unit must be shielded For cables connecting to PCMCIA cards see the option manual or installation instructions Trademark Acknowledgements iPad iPhone are the registered trademarks of Apple Inc Android M is a trademark
18. cally When the configurations are saved successfully you ll see a message indicating the IP address and port number assigned to your camera Note down the IP address and port number and log out the camera BM Wizard Config amp admin Logout E Live View 22 UPnP e l UPnP UPnP Configuration UPnP O vsti Friendly Name IP CAMERA Fixed AVN806 000E5320E73E Port Mapping Configuration Port Mapping oios Seme ome Your IP Camera is accessible from the other side of the router using the following URL http 60 248 97 4 80 or https 60 248 97 4 59207 Router IP LAN 1P Address HTTP Port 80 HTTPS Port 59207 f set to blank or 0 a port number wil be set automatically upon enable Check your connection Step1 Connect your laptop PC to Internet with the wireless network other than the one AVM301 is connected Step2 Enter the IP address or host name you just noted down and the port number in the URL address box of the web browser and see if you can enter the login page of the camera successfully The format is http ipaddress portnum or http hostname portnum 1 3 2 Configure on iPhone iPad Before configuring this camera on iPhone iPad make sure gt You have installed our mobile program EagleEyes Lite or EagleEyes Plus on your iPhone or iPad For details please refer to APPENDIX 2 MOBILE SURVEILLANCE VIA EAGLEEYES at page 16 Note EagleEyes HD for iPad doesn t
19. ccnccconcnccocccnnoonccononconononnoonocanonnonanonnonnnnanon 17 APRENDO A A O Anido 18 1 CAMERA NETWORK CONFIGURATIONS Please follow the instructions below to finish camera installation and network configurations You may configure the network connection of this network camera with your laptop computer or with your iPhone or iPad based on your network environment 1 1 Assemble amp Install Camera Y O O gt Step1 Fasten the base of the bracket the round one to where the camera is installed Note The distance between your camera and the location you want to monitor should be 3 4 meters for the built in human detection function to work properly Step2 Assemble the bracket and the camera and adjust the viewing angle of the camera Step3 Connect the supplied power adapter to the camera s power jack DC 5V 2A on the rear panel and the power outlet Step4 Continue to proceed network configurations as instructed in the following sections 1 2 Understand How Your Laptop Computer Connect to Internet 1 Wireless router Modem PC El Laptop Wireless Modem Router Devices connected with a network cable Devices connected wirelessly 2 Router Modem PC 6555 eee Laptop r Router Modem 3 Modem or Modem Hub gt Modem Devices connected with a network cable Then connect your network camera directly
20. dress The default port number is 88 You may change it to any value such as 8080 if the port number of 88 is AN blocked Port 88 DNS 168 95 1 1 Account User Name admin Password 00000 MAC 00 0e 53 1e 2e 2b al PRIME S FF6333 O 88 Gat Step4 Select Apply to confirm all your changes Then wait till you see Done or Fail in Status Regardless which message you see proceed as DNS 198 95 1 1 instructed below Account E For Done you ll return to the new device page User Name admin m For Fail select E on the top right side You ll later be Password e prompted to select DDNS or Local IP Select DDNS Status Change and return to the new device page E ronesateze Y When Selecting Apply DDNS MAC000e531e2e2b ddns eagleeyes tw Processing y 3 Status Processing Done or Fail ill PIA S F4F6 33 O 95 tab Step5 In the new device page give a meaningful name for this connection in Title and click Save Required Please continue with configuring port forwarding as instructed in APPENDIX 3 CONFIGURE PORT FORWARDING at page 17 IP Address MAC000e531e2e2b Port 88 Username boss Password essonbes Get Type IPCAM FIX Optional Audio OFF CH1 Check vour connection Step1 Switch the network mode to 3G mode on iPhone or iPad Step2 Start EagleEyes and select the connection you just added to see if you can access the camera
21. dress 4 92 4 68 4 XXX M 21005 Packet Scheduler IP address 192 168 1 238 4 gt 55 a t 10 Ed 2 File and Printer Sharing for Microsoft Networks ida A excep M Intemet Protocol Version 6 TCP IPv6 a eines dol EFS Intemet Protocol Version 4 TCP IPv4 du Internet Protocol Version 4 TCP IPv4 Default gateway Wi Link Layer Topology Discovery Mapper 1 0 Driver Wi Link Layer Topology Discovery Responder AAA O Use the following DNS server addresses Install Jninsta Properties Properties Preferred DNS server Description Alternate DNS server Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication across diverse interconnected networks OK Cancel e Click OK to close the Internet Protocol Version 4 TCP IPv4 Properties dialog box Then click Close to close the Local Area Connection Properties dialog box 15 APPENDIX 2 MOBILE SURVEILLANCE VIA EAGLEEYES EagleEyes is a mobile phone program used with our surveillance system for remote surveillance It has several advantages E ts free Except EagleEyes Plus for iPhone E It s compatible with several popular mobile platforms such as iPhone iPad and Android It s easy to download install and configure For more details about configuring and operating this program please visit our official website www eagleeyescctv com
22. for the appropriate IP settings amp DVB Net ETAdapter Obtain an IP address automatically Use the following IP address This connection uses the following items v o Client for Microsoft Networks M 2 005 Packet Scheduler Y 23 File and Printer Sharing for Microsoft Networks a ride Protocol Version 6 TCP IPv6 Subnet mask 255 255 255 0 MRS intemet Protocol Version 4 TCP IPv4 Internet Protocol Version 4 TCP IPv4 Default gateway Y Link Layer Topology Discovery Mapper 1 0 Dri Y Link Layer Topology Discovery Responder 192 168 1 XXX 1 255 except 10 IP address 192 168 1 238 Obtain DNS server address automatically Use the following DNS server addresses Uninstal Properties Properties Preferred DNS server O Description Transmission Control Protocol Intemet Protocol The default Alternate DNS server wide area network protocol that provides communication across diverse interconnected networks e Click OK to close the Internet Protocol Version 4 TCP IPv4 Properties dialog box Then click Close to close the Local Area Connection Properties dialog box For Windows 7 users a Select y start gt Control Panel gt Network and Internet to enter the Network and Sharing Center Then click Change adapter settings E Control Panel Home View your basic network infor Change adapter
23. illance within your iPhone Working hand in hand EE to you even when you are on the road and allows non your treasured property lf you have controllable When the download is completed EagleEyes will be installed automatically to the location where all applications are saved in your phone by default or where you specify Note For more details about configuring and operating this program please visit our official website www eagleeyescctv com 16 APPENDIX 3 CONFIGURE PORT FORWARDING You need to additionally access your router for port forwarding when your router doesn t support UPnP Each router has different setting page Here we re taking D Link wireless router as an example Step1 Access your router for port forwarding f you re configuring AVM301 with laptop PC or iPhone iPad over wireless network open your web browser e g Internet Explorer or Safari and enter the IP address of your router f you re configuring AVM301 with laptop PC over LAN disconnect AVM301 and connect to your router Then open your browser e g Internet Explorer and enter the IP address of your router Step2 In the router setting interface go to the port forwarding or virtual server rule configuration page Note The naming of port forwarding or virtual server may vary based on different router brands To know where it is please refer to the user manual of your router Then enter the IP address and port number you set for
24. of Google Inc Use of this trademark is subject to Google Permissions Microsoft Windows amp Internet Explorer are registered trademarks of Microsoft Corporation in the United States and or other countries Disclaimer AVTECH reserves the right to revise or remove any content in this manual at any time We do not warrant or assume any legal liability or responsibility for the accuracy completeness or usefulness of this manual The content of this manual is subject to change without notice MPEG4 Licensing THIS PRODUCT IS LICENSED UNDER THE MPEG4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON COMMERCIAL USE OF A CONSUMER FOR i ENCODING VIDEO IN COMPLIANCE WITH THE MPEG4 VISUAL STANDARD MPEG 4 VIDEO AND OR ii DECODING MPEG4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON COMMERCIAL ACTIVITY AND OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE MPEG4 VIDEO NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA LLC SEE HTT P WWW MPEGLA COM GPL Licensing This product contains codes which are developed by Third Party Companies and which are subject to the GNU General Public License GPL or the GNU Lesser Public License LGPL The GPL Code used in this product is released without warranty and is subject to the copyright
25. of the corresponding author Further source codes which are subject to the GPL licenses are available upon request We are pleased to provide our modifications to the Linux Kernel as well as a few new commands and some tools to get you into the code The codes are provided on the FTP site and please download them from the following site or you can refer to your distributor http download dvrtw com tw GPL 076D_ Series arm linux 2 6 tar gz TABLE OF CONTENTS 1 CAMERA NETWORK CONFIGURATIONS 0 00 c ccc cece esc eecceceeeeeeeseeseeueaueuueaueaueueeeeeeeeeaeeaesauenueeeas 1 1AASSemble se Install Camera nc ida 1 1 2 Understand How Your Laptop Computer Connect to Internet cccoooccnnccnncccccnnnncnncnnannnnnnnancnnnnnarennnnnos 1 1 3 Wireless Ro ter F MOE ar DS 2 Sl COMIQUEROS e DR o dd 2 1 3962 GONIgure 0n IPHONES IP AG ini a 4 ROUE ENOG rra oa arado li 6 125 Modem IUD lt b MOE tados 8 1 6 Mame DSTA ACCOUN Li A ei 11 MBA Fr OM Vi CD IB FOW SON it A 11 102 FOIOS ac dias 11 2 BEFORE VOUS VAR TO USE sicario 12 Zoli VMISO A US MEL ios asad cada 12 APPENDIX 1 CHANGE IP ADDRESS OF YOUR LAPTOP PCoonocccccncnncnncnnnnnnonanononanonananonccnnoncnnnnns 13 APPENDIX 2 MOBILE SURVEILLANCE VIA EAGLEEYES 20 0 cccecceceeeeeeee eee seeeeeeeeesaeeaeeanees 16 Ae A FeO GUIS IC AAA attend Gcruenclentien E ne rulnatcueutinaam iene namatioreuemeanens 16 A22 Where O downoad suso 16 APPENDIX 3 CONFIGURE PORT FORWARDING oocooccccccn
26. our laptop PC is changed to 192 168 1 xxx 1 255 except 10 To know how to change please refer to APPENDIX 1 CHANGE IP ADDRESS OF YOUR LAPTOP PC at page 13 Step2 Open the web browser such as Internet Explorer on your laptop PC and enter http 192 168 1 10 88 on the URL column to access this camera In the login page enter the user name password and security code to access Note The default user name and password for remote access are both admin 8 Step3 The wizard starts to analyze your network environment When it s completed select One Step Wizard to enter the quick camera setting page Wizard Step1 Network Environment Starting Wizard C Do not start wizard at Analyzing the network environment Ep 30 One Step Wizard x Account Date and Time Username Date 2011 09 20 Password Time 15 el 28 ml 136 kai Mew Password Confirm Password Network IP Type 0 Static IP PPPoE DHCP Username c33158935 Password seeee Port 80 DNS1 168 95 1 1 DNS2 0 0 0 0 MAC Address 00 0e 53 1d 6f f1 2 DONS A Wizard x Close A save Item Description Account Change your default account password if needed This change can also be made in Config gt General 3 Account Date and Time Check and select the current date and time Network Configure your network setting based on the network type you re using For details please refer
27. rking a nternet Esas or pick a Control P el icon 2 Network Diagnostics w a Internet Options Network Connections E po b In LAN or High Speed Internet right click on Local Area Connection and select Properties LAN or High Speed Internet Network Tasks Other Places i Local Area Connection nabled Firenalle E WED PCHET Disable g Control Panel Status a My Network Places caul 1 My Documents Bridge Connections ig My Computer Create Shortcut Rename Note If your local area connection is not enabled please also enable it gt gt Details Properties Local Area Connection c In the General tab select Internet Protocol TCP IP and select Properties d In the General tab select Use the following IP address and set the IP address to 192 168 1 XXX XXX can be any value from 1 255 except 10 Note It s recommended to note down the current settings first and then change as instructed It s helpful when you need to restore the PC network settings for connecting to Internet later e Click OK to close the Internet Protocol TCP IP Properties dialog box Then click Close to close the Local Area Connection Properties dialog box 13 For Windows Vista users a Select dii start gt Control Panel gt Network and Internet to enter the Network and Sharing Center Then click M
28. rmat is http hostname portnum 10 1 6 Change Default Account To ensure your account safety please access the camera after network configuration to change the default user name and password with new one you prefer 1 6 1 From Web Browser Log into the camera and select Config gt General gt Account You may NW Select the default account admin and click Edit to change the default password or m Directly click Add to create a new account and remove the default account Account Username User Level Life Time admin SUPERVISOR INFINITE os C add edit Delete gt C add Edit New Account Info x Palit Account kako x Username office Username admin Password eececesee Password e o Confirm Password o Confirm Password eeeceses User Level SUPERVISOR v User Level SUPERVISOR v Life Time INFINITE lv Life Time INFINITE v f save 2 Close E save Bg Close 1 6 2 From iPhone iPad Log into the camera and click E gt on the top right corner to enter the system configuration page Then select Advance Setup gt Account You may NW Select the default account admin and click Edit to modify the default password or mE Directly click Add to create a new account and remove the default account Username User Level Life Time admin SUPERVISOR INFINITE Add user info Edit user info
29. settings ge adap A Changead ced sharing settings WIN IDL2GU4VA2G This computer Change adapter settings x Network Public network 14 b Right click on Local Area Connection and select Properties Gori t Control Panel Network an File Edit View Tools Advanced Help Organize A ls Local Area Connection gt el ES Broadcom NetXtreme 57x Gigabi Note If your local area connection is not enabled please also enable it c In the Networking tab select Internet Protocol Version 4 TCP IPv4 and select Properties d In the General tab select Use the following IP address and set the IP address as described below Note It s recommended to note down the current settings first and then change as instructed It s heloful when you need to restore the PC network settings for connecting to Internet later r Y Local Area Connection 3 Properties i 2 Internet Protocol Version 4 TCP 1Pv4 Properties E Networking Sharing l General Connect using You can get IP settings assigned automatically if your network supports a DVB Net ETAdapter this capability Otherwise you need to ask your network administrator for the appropriate IP settings This connection uses the following items Obtain an IP address automatically Y Cat kr Mc ds O Use the following IP ad
30. support network configuration Please install EagleEyes Lite or EagleEyes Plus on your iPad instead gt Recommended Your wireless router supports UPnP and this function is enabled Note If your wireless router doesn t support UPnP you need to additionally access your router for port forwarding For details please refer to APPENDIX 3 CONFIGURE PORT FORWARDING at page 17 gt Your camera is connected to your wireless router with a RJ45 network cable and It s powered on Note Check LAN status indicator is always on not blinking If it s blinking check your RJ 45 network cable and ensure it s not disconnected or defect gt You have checked the IP address used by your wireless router with AVM301 connected as instructed below and written it down You ll need it later Connect your iPhone iPad to the wireless router with AVM301 connected and go to Settings gt Wi Fi Select gt near the selected wireless network to enter the details The IP address shown in Router is the IP address used by your wireless router In the following example the IP address of your router is 192 168 2 7 ail PARE T F45 16 98 Ge all Pais gt TP F5 16 O 98 i TEMI A AL A E i ve HE i WI FI Networks MN poa i Networks Wi Fi Forget this Network Choose a Network IP Address CH COM a BootP Static CONFERENCE az IP Address 192 168 2 101 MEETING a Subnet Mask 255 25
31. ure is up to 30 C To get more accurate and precise detection you may connect external alarm devices such as magnetic contacts There re some tips for installation For details please go to www eagleeyescctv com supp QnA aspx Please try adjusting the power line frequency to 60 Hz or 50 Hz for the Camera For iPhone users access the camera and select ED on the top right corner to enter IPCAM Configuration page Then go to Advance Setup gt Camera to change setting For access from Internet Explorer log into the camera and select Config gt Camera gt Camera 18
32. xx means any value from 2 50 and change the gateway to 192 168 2 1 the same as the IP address of your router Then change the port number to any value other than 88 if needed Note Make sure the P address you change is not used by other devices connected to the same router Step4 Enter the user name and password of this camera to confirm the change and exit IPScan The default user name and password are both admin Step5 Open the web browser such as Internet Explorer on your laptop PC and enter the IP address you just set on the URL column to access this camera In the login page enter the user name password and security code to access Note Please skip the wizard Step6 Go to Config gt DDNS and enable the DDNS service Wizard Config amp admin Logout Live View amp 2 DDNS x Co nfig 4 DDNS DDNS Configuration DDNS Enable D Disable System Name default y Hostname MACOO0ES320E73E ddns eagleeyes tw E Mail EH f your router supports UPnP please proceed Step7 E f your router doesn t support UPnP note down the host name such as MAC000e531d6ff1 ddns eagleeyes tw and click Save Then access your wireless router for port forwarding as instructed in APPENDIX 3 CONFIGURE PORT FORWARDING at page 17 Step7 Go to UPnP and enable the UPnP service Then enable Port Mapping and click Save to start port mapping automati
Download Pdf Manuals
Related Search