KT-LCD2 eBike Display User Manual Functions and Display
Contents
1. KT LCD2 eBike Display User Manual V2 5 Dear customer please read this manual before you use KT LCD2 instrument The manual will guide you use the instrument correctly to achieve a variety of vehicle control and vehicle status display Functions and Display Instruments using the structure form of instrument body portion and the operation buttons are designed separately Riding speed imperial O oo Toate C wergea o ASSIST Pse Operation 1 ON OFF Hold V button long to turn on the power and hold LO long for a second time to turn off the power When the motor stops driving and when the e bike is not used for a consecutive 5 minutes it will automatically shut down and turn off the motor power supply 2 Display interface Hold ROF button to start up and enter display interface w p88BBE 2 1 Turn on backlight and headlights Hold Aa long to turn on backlight and headlights the controller should have headlight drive output function hold a long again to turn off the backlight and headlights 2 2 Assist ratio gear ASSIST switch Hold A or Y shortly to switch 1 5 file gear Gear 1 is EFA m G bo ASSIST ry ry f c OO for the minimum power gear 5 is for the highest power Each mla startup will automatically restore the gear shutdown last time Gear 0 is without booster function dma 90 08 0 8 8 LI not more than 6Km h Release iv button the function is Hold iv and R2. flashes the vehicle drives at the speed invalid After power on for 5 seconds hold a and y at the am BODO same time single trip riding time TM and single trip distance CI Gj amp OO 4 2 9999A DST flash hold K button shortly the content of both is cleared If failed holding the button within 5 seconds it will automatically return the display interface after 5 seconds original content is preserved 2 5 Display of total trip time and distance LO SON w DODO Hold amp button shortly to display of total trip time TTM a FOC Ow OO 4 w LI 9558s and total trip distance ODO hold LD button shortly again to return the display interface In the riding mode after 5 seconds automatically returns to display interface 2 6 Display of single maximum speed and average speed In the display of total trip time and distance hold or mm 000 OU Ges C BBB Y shortly to display of single maximum speed MXS and average speed AVS hold D button shortly again to return the display interface In the riding condition 5 seconds later automatically returns to display interface 2 7 Battery capacity indicator display The meter can automatically identify the battery capacity when the battery capacity indicator is supporting use with the specified controller When the battery capacity is over 70 the four power displays of the meter are lit and the battery capacities drop the
3. four power displays are off in order when the power capacity is less than 15 the four power displays are totally turned off When the controller is under the protection of voltage shortage the power capacity indicator flashes indicating the vehicle is under voltage shortage and power off 3 Error Code display Electronic control system failure will display flashing fault code Once the fault was removed it automatically exits from the fault code display interface Error Code Definition 01__info Throttle Abnormality 03 info Motor hall signal Abnormality 04 info Torque sensor signal Abnormality 05__info Axis speed sensor Abnormality only applied to torque sensor 06__info Motor or controller has short circuit Abnormality General Project Setting 1 Set maximum riding speed After power on for 5 seconds hold Aa and ivy at the same time maximum riding speed Km H flash hold aA or W shortly to set the maximum riding speed default 25Km H Hold LD button shortly and go to the next parameter settings The wheel diameter will be set after finishing setting the maximum riding speed wheel diameter specifications flashes Hold A or Wd shortly to set the specifications of wheel diameter Select the range8 10 12 14 16 18 20 22 24 26 700c and 28 inches Hold LO button shortly and go to the next parameter settings The metric units will be set after finishing setting wheel diameter Km H and Km or MPH and Mil flash Ho
4. ld a or Wd shortly and select the metric units of speed and mileage in synchronization wee pet Mil 4 Hold V button shortly Km H and Km or MPH and Mil stop flash after metric unit setting is completed Hold LO button shortly again to re enter the maximum riding speed setting interface or hold wD button long to exit from setting environment of routine projects and save the setting values returning to display interface 5 Exit from routine project setting All three routine project settings can exit from the setting environment and return to the display if hold button long after each setting is completed meanwhile the setting values are saved Under each setting interface if the button failed holding for more than 1 minute it will automatically return to display interface and the setting value is invalid Outline Drawings and Dimensions 1 Dimensions of instrument body Rear view Side view 2 Wiring diagram f PY f oa O E a D VB Red 1 a Control Blue H v GND Black FA One Datal Green Data2 Yellow K Prepared by Suzhou Kunteng Electronics Co Ltd
Download Pdf Manuals
Related Search