Trotec T660 Operating Manual
Contents
1. e 1 An The selected material is anhydrite screed e 2Ce The selected material is cementitious screed Please note that in case of the settings 1 and 2 an additional value will be indicated in the upper measurement value display 14 Itis a combination of the material 1 or 2 and the calculated per centage e Example 2_7 5 7 5 with cementitious screed Select MAT 17 whilst in configuration mode Press the OK button 10 Select the desired value by use of the Up 7 or Down 9 key Press the OK button 10 for approx 2 seconds The device switches to measuring mode With either setting 1 or 2 the indication MAT 17 continues to be displayed PON gt Setting the offset By use of CAL a single point calibration can be carried out for the selected sensor indications All sensors are already factory cali brated and have a corresponding characteristic calibration curve By stating a calibration value offset a global shift of the calibra tion curve which has an effect on the entire measuring range is performed for the single point calibration The offset value to be entered is that value by which the calibration curve will be shifted Example The displayed value is always 5 too high gt change the offset value for this measurement channel to 5 The offset value s default setting is 0 0 Changing the offset value brings about an automatic reset of the measured values 1 Select CAL 17 whilst in co2. entation Display digit Building moisture zone lt 40 digits dry 40 80 digits damp gt 80 digits wet PC software Use the MultiMeasure Studio Standard PC software free standard version or MultiMeasure Studio Professional paid professional version dongle required to carry out a detailed analysis and vis ualisation of your measured results You can only use all config uration visualisation and functional options of the device when using this PC software and a TROTEC USB dongle professional Installation requirements Ensure that the following minimum requirements for installing the MultiMeasure Studio Standard or MultiMeasure Studio Professional PC software are fulfilled e Supported operating systems 32 or 64 bit version Windows XP from service pack 3 Windows Vista Windows 7 Windows 8 e Software requirements Microsoft Excel to display stored Excel files Microsoft NET Framework 3 5 SP1 is otherwise automat ically installed during the software installation e Hardware requirements Processor speed min 1 0 GHz USB connection Internet connection 512 MB RAM minimum 1 GB hard disk space minimum Optional TROTEC USB dongle Professional for using the professional version of the PC software Operating manual Material moisture measuring device T660 DTROTEC Installing the PC software 1 Download the current PC so
3. for approx 4 seconds until a beep is emitted The device will be switched off Measuring principle The measurement is effected according to the dielectric measur ing principle Notes regarding the measurement principle e The measurement results are only to be used as reference for a rough orientation e An important variable influencing the measured value is the bulk density of the good to be measured The higher the bulk density the higher the measured value e Before measuring the measuring pointis to be cleared of any impurities e g paint residues dust e f the material to be measured contains metal e g nails screws lines pipes etc and is situated within the sensor s measuring field the measured value skyrockets In that event the measurement is not conclusive e When the ball head is held to corners e g window frames the measured value is generally higher because there is more matter in the measuring head s stray field Toward a corner a distance of more than 8 to 10 cm has to be ob served e During the measurement always hold the measuring head 6 in a vertical position to the measured material press it to the surface and do not tilt it e Rough surfaces will always result in a too low measured val ue e Depending on the material s bulk density the device s impact depth amounts to 20 to 40 mm Conclusions regarding zones located at a lower level cannot be drawn e With material t
4. help text of the software Errors and faults The accurate functionality of the device was tested during pro duction a number of times However if functionality faults do occur then check the device according to the following list The device does not switch on e Check the charging status of the batteries Change the bat teries when the message Batt lo is displayed upon switch on e Check that the batteries are properly positioned Check the polarity is correct e Never carry out an electrical check yourself instead contact your TROTEC customer service Maintenance For maintenance or repair work which requires the A housing to be opened contact TROTEC customer service Devices which have been opened unlaw fully are void of any warranty and warranty claims Cleaning the device 1 Use a soft lint free cloth for cleaning 2 Dampen the cloth with clean water Do not use sprays sol vents alcohol based or abrasive cleaners to dampen the cloth 3 Clear dirt from the housing the connections and the colour display Battery change Change the batteries when the message Batt lo is displayed upon switch on or the device can no longer be switched on See Insert ing the batteries on page 4 Operating manual Material moisture measuring device T660 D TROTEC Disposal In the European Union electronic equipment must not be treated as domestic waste but must be disposed of ma Professionally in accor
5. TRT BA T660 TC 001 EN T660 D TROTEC T660 D a 4 fi Cs MADE IN GERMANY OPERATING MANUAL MATERIAL MOISTURE MEASURING DEVICE gt TROTEC AT WORK D TROTEC Table of contents Notes regarding the operating manual uuenneneeenenneneeenennen 1 Information about the deviCE o ooccccncnnonicncnnonconcononcnnoncnnnons 2 Technical data cccccsscesessssssssesseessesssssescerseessesensesseeaees 3 MN ii a iia 3 Transport and storage oococccccconococncononcconnnononncononononnonnoncncnnnns 4 UO OF AU OMIM ie oi 4 Measuring principle c ccscscescssccsecsecsesssssessessessasersenseaes 8 PC SORWANG na Aes 9 Errors and faults ccccsscssescsscsecssssceessessssessessessessessssseeseeses 10 Maintenance ccccscccssessesssecsessessessessenseessescessneseesessnesseass 10 Disposalscnsssssean alas 11 Declaration of conformity coconccccoconccnnonanconconcnnnanoncnnoncnnnons 11 Notes regarding the operating manual Symbols A Danger Warns of a hazard which can lead to personal injury Caution Warns of a hazard which can lead to damage to prop erty The current version of the operating manual can be found at www trotec de Legal notice This release replaces all previous versions No part of this publi cation may be reproduced without written permission from TRO TEC The same applies for electronically processing duplicating or
6. ated The lower measurement value display 16 flashes 5 Press the keys Left menu 11 or Right back 8 to select a digit The selected digit flashes 6 Press the Up 7 or Down 9 key to change the value of the Configuration mode Description selected digit ALARM Setting the threshold value tor the alarm 7 Repeat the steps 5 and 6 until the value is set as desired Lamp Adjusting the display illumination 8 Press the OK button 10 for approx 2 seconds MAT Material settings The alarm was set based on your choice CAL Setting the offset E The device switches to measuring mode With activated alarm function the indication ALARM 17 continues to be displayed Adjusting the display illumination The display illumination can be adjusted within a range of 20 to 100 Another available setting is AL on AL on features a brightness of 100 and deactivates the automatic switch off function 1 Select the lamp 17 whilst in configuration mode 2 Press the OK button 10 to confirm 3 Select the desired value by use of the Up 7 or Down 9 key 4 Press the OK button 10 for approx 2 seconds The set value will be adopted The device switches to measuring mode EN Operating manual Material moisture measuring device T660 D TROTEC Material settings Here you can select the construction material for the measure ment The following options are available e Ono No material selected
7. dance with Directive 2002 96 EC of the European Parliament and Council of 27th January 2003 concerning old electrical and electronic equipment After the end of its use please dispose of this device in a manner appropriate to the relevant legal requirements In the European Union batteries must not be treated as domestic waste but must be disposed of professionally in accordance with Directive 2006 66 EC of the European Parliament and Council of 6th September 2006 concerning batteries and accumulators Please dispose of batteries in a manner appropriate to the rele vant legal requirements Declaration of conformity in accordance with the EC Low Voltage Directive 2006 95 EC and the EC Directive 2004 108 EC about electromagnetic compatibil ity Herewith we declare that the T660 material moisture measuring device was developed constructed and produced in compliance with the named EC directives The C marking is found on the rear of the device Manufacturer Trotec GmbH amp Co KG Grebbener Stra e 7 D 52525 Heinsberg Phone 49 2452 962 400 Fax 49 2452 962 200 E mail info trotec de Heinsberg 31 03 2014 Managing Director Detlef von der Lieck Operating manual Material moisture measuring device T660
8. ect sunlight e Observe the storage and operating conditions see chapter Technical data Intended use Only use the material moisture measuring device T660 for the moisture measurement of building materials Here read and observe the technical data To use the device for its intended use only connect and use accessories and spare parts which have been approved by TROTEC Improper use Do not use the device in potentially explosive atmospheres or for measurements in liquids TROTEC accepts no liability for dam ages resulting from improper use In such a case entitlements to a warranty are forfeited Any unauthorised modifications altera tions or structural changes to the device are forbidden Personnel qualifications People who use this device must e have read and understood the operating manual especially the Safety chapter For maintenance or repair work which requires the housing to be opened contact TROTEC customer service Devices which have been opened unlawfully are void of any warranty and warranty claims Residual risks A Danger Do not leave the packaging lying around Children may use it as a dangerous toy Danger The device is not a toy and does not belong in the hands of children Danger Dangers can occur at the device when it is used by untrained people in an unprofessional or improper way Observe the personnel qualifications Caution To prevent damages to the device do not expose
9. ent value display bottom 17 Configuration mode options Operating manual Material moisture measuring device T660 D TROTEC Technical data Value T660 209 mm x 63 mm x 35 mm approx 300 g Parameter Model Dimensions L x W x H Weight incl batteries Measuring range 0 to 200 digits Operating range Operating temperature 0 C to 50 C Relative humidity lt 90 or lt 20 g m non condensing Storage Relative humidity lt 95 non condensing Ambient temperature 20 C to 60 C Energy Battery 4 x Alkaline LR6 AA 1 5 V batteries comparable NiMH rechargeable batteries gt 2500 mAh approx 80 mA approx 70 pA at least 30 h Current consumption active Current consumption passive Battery life Scope of delivery The scope of delivery includes e 1x Material moisture measuring device T660 e 1xUSB cable e 4x Alkaline LR6 AA 1 5 V batteries e 1x Display protection film e 1x Getting started guide e 1x Factory test certificate Safety Carefully read the operating manual before using the device and keep it within reach e Do notuse the device in atmospheres containing oil sulphur chlorine or salt e Never use the device for measurements at live parts e Ensure that all connection cables are protected from damag es e g from kinks or crushing e Protect the device from permanent dir
10. ftware from the Internet To do so visit the website www trotec de First click on Service followed by Downloads and then Software Select the MultiMeasure Studio Standard software from the list If you want to use the optionally available professional version of the PC software MultiMeasure Studio Professional dongle then get in touch with your TROTEC customer service 2 Double click on the downloaded file to start the installation 3 Follow the instructions of the installation wizard Starting the PC software 1 Connect the device to your PC via the USB connection cable provided in the scope of delivery ZA lt gt Note Step 2 only needs to be performed when using the Professional software functions If you only use the Standard software functions please proceed to step 3 2 In order to enable the Professional functions connect the TROTEC USB dongle to a free USB port on your PC The TROTEC USB dongle Professional is automatically detected by the operating system If you only connect the TROTEC USB dongle Professional to your PC after starting the PC software click the Parameters menu item in the PC software Afterwards click the USB symbol dongle check to read the connected TROTEC USB dongle Professional Switch on the device see chapter Switching on on page 4 Start the MultiMeasure Studio software Information regarding the use of the MultiMeasure Studio software is provided in the
11. he On Off key 4 again The device emits a short beep The following message appears on the display LoC off Key lock is no longer activated Operating manual Material moisture measuring device T660 DTROTEC Configuration mode 1 Press the Left menu key 11 for approx 2 seconds The device emits a short beep The CFG symbol 12 is displayed in the upper right corner The available options for configuration mode 17 are dis played 2 Use the cross control 2 to select the desired option 3 Confirm the selection by pressing the OK button 10 The selected symbol will be illuminated crc 12 HOLD MAX MIN AVG ACT Y CAL 17 MAT Alarm Setting the alarm Here you can determine the limit value for the alarm function Upon exceeding this value the device emits an acoustic signal and the indication ALARM 17 flashes The alarm function draws on the current digit measured value The limit value can be deter mined within a range of 0 to 200 1 Select ALARM 17 whilst in configuration mode 2 Press the OK button 10 to confirm The upper measurement value display 14 flashes 3 Press the Up 7 or Down 9 key to activate or deactivate the alarm On or Off will be indicated in the upper measurement value display 14 4 Press the Right back key 8 Depending on the selection the alarm is either activated or deactiv
12. hicknesses of less than 20 mm there is a dan ger of humidity values from adjacent material layers affecting the measured value e The dielectric measurement method s main area of use con sists in comparative measurements at the same construction material or similar components Therefore this method is well suited for the examination of water damage leak detec tion and the localization of moisture zones for the purpose of marking the measuring spot for CM measurements Measured value assessment for wood The measurement result is either in the dry or the saturated area Saturated means that in addition to the water bound within the wood there is further liquid If there is hence a measured value of more than 80 the wood is most like soaked Display digit Wood moisture zone lt 50 digits dry gt 80 digits limit to the saturated range Since the measurement value displays of the dielectric measure ment method depending on marginal conditions are subject to great fluctuations a resistance measurement is always prefer able in particular for the determination of wood moisture Operating manual Material moisture measuring device T660 D TROTEC Measured value assessment for building material For building materials the measurement results of the dielectric measuring method can only be used as reference for a rough ori entation Conclusions with respect to absolute humidity in mass M ca
13. it to extreme temperatures extreme humidity or moisture Caution Do not use abrasive cleaners or solvents to clean the device gt bb Operating manual Material moisture measuring device T660 DTROTEC Transport and storage Transport Use a suitable bag to transport the device safely Storage When the device is not being used observe the following storage conditions e dry e protected from dust and direct sunlight e with a plastic cover to protect it from invasive dust if neces sary e The storage temperature is the same as the range given in the chapter Technical data e When storing the device for a long time remove the batteries Accessories Optionally the following accessories are available for transport and storage e TROTEC Holster 3 For further information please contact your TROTEC customer service Operation Inserting the batteries e Insert the supplied batteries before first use n Caution Make certain that the surface of the device is dry and the device is switched off 1 Open the cover of the battery compartment 3 2 Insert the batteries in the compartment as indicated in the figure 3 Close the cover of the battery compartment 3 The device can now be switched on Switching on Note The cross control is very sensitive Therefore avoid dirt on the control panel because it could be misinterpreted by the device as keystroke Before use make
14. m fw dd j 1 Hold the measuring device at the black rubber surfaces and maintain this position for otherwise the measurement results might be falsified 2 Firmly place the measuring head in a vertical position on the good to be measured Observe a minimum distance of 8 to 10 cm to corners Read the measured value from the display Carrying out a comparative measurement 1 Look for a preferably dry spot at the component 2 Perform a measurement as previously described The thus determined measured value will be the reference value for dry 3 Look for a preferably damp or wet spot at the component if any 4 Perform a measurement as previously described With regard to the present conditions the thus determined measured value will be the reference value for damp wet 5 Carry out further measurements at the component Higher measured values usually signify a higher moisture content in the near surface area of the material to be measured Particularly for larger areas it is always recommended to perform measurements in form of a preferably close meshed grid for it is only this way that changes in the moisture content of the material can relatively confidently be detected and occasional outliers minimized Key lock 1 Briefly press the On Off key 4 during operation The device emits a short beep The following message appears on the display LoC on Key lock is activated 2 Press t
15. m measured value MAX Maximum measured value HOLD Measured value will be held Holding the measured value 1 Setthe measuring mode to HOLD The current measured value will be held and displayed The device will hold this value until the measured values are set back or the device is switched off Resetting the measured values 1 Press the OK button 10 for approx 2 seconds All previously stored measured values of the measuring modes AVG MIN MAX and HOLD will be set back All measured values are then determined anew based on the measurement proceeding in the background Operating manual Material moisture measuring device T660 DTROTEC Checking current settings 1 Press the Right back key 8 for approx 2 seconds The selected settings are indicated in the two measure ment value displays 14 16 Measured value storage Please note that measured values cannot be saved on the device itself In order to save measured values the device has to be con nected to a PC via a USB cable using the MultiMeasure Studio software 1 Briefly press the OK button 10 The displayed measured value will be saved in the soft ware Further information can be gathered from the help text of the MultiMeasure Studio software USB interface The device can be connected to a PC via the USB interface 5 See chapter PC software on page 9 Switch off 1 Press and hold the On Off key 4
16. n making a warranty claim supply the device number see the rear of the device The invoice acts as warranty certificate When manufacturer s instructions or legal regulations have not been followed or after unauthorised changes to the device are made the manufacturer is not respon sible for the resulting damages Changes to the device or unau thorised replacement of individual parts can drastically impact the electrical safety of this product and leads to the forfeit of the warranty Liability does not extend to damages to people or prop erty caused by the device being used other than as described in the instructions in this operating manual Subject to changes to technical design and model changes as part of constant develop ment and product improvement without prior notice No liability is accepted for damages resulting from improper use In such cases entitlements to a warranty are then also forfeited Operating manual Material moisture measuring device T660 DTROTEC Information about the device Description of the device The material moisture measuring device T660 is a dielectric humidity sensor which can be used for the quick and non destructive localization of humidity or moisture distributions The device enables the detection of near surface moisture in walls or flooring The measured values will be displayed in real time A minimum maximum and average function is available for the direct analysis of the meas
17. n only be drawn for measurements performed with the exact same marginal conditions and compositions of the building material as indicated for the test set up in the chart below This graph was created in collaboration with the Institute of Build ing Materials Research of the RWTH Aachen IBAC and illustrates the correlation between the measured value and the mass related moisture content of the examined building materi als 8 7 H anhydrite floating screed 1 A 6 cementitious screed 2 Al 1 C 30 37 concrete 3 1 M 5 z 4 i a a r 2 7 _ 1 0 0 10 20 30 40 50 60 70 80 90 100 110 120 130 Measured value digits 1 E M CM E3 CM M 1 5 2 G The spread of the achieved measurement results for the dielectric measuring method is clearly higher than for the resistance meas uring method The dielectric measuring method is not suited for the quantitative but only for the qualitative moisture measurement in near surface areas The indicated measured values are not the result of a qualified moisture measurement as per VOB German Construction Con tract Procedures or relevant specialist regulations The measured values are only to be interpreted as indicators dry damp wet For building materials the measurement results of the dielectric measuring method can only be used as reference for a rough ori
18. nfiguration mode 2 Press the OK button 10 3 Press the keys Left menu 11 or Right back 8 to select a digit The selected digit flashes 4 Press the Up 7 or Down 9 key to change the value of the selected digit 5 Repeat the steps 5 and 6 until the value is set as desired 6 Press the OK button 10 for approx 2 seconds The offset is set The device switches to measuring mode With set offset value the indication CAL 17 continues to be displayed Exiting configuration mode Configuration mode will automatically be terminated after 8 sec onds without entry You can quit configuration mode yourself anytime Please note that in such an event no changes made to the settings will be adopted 1 Press the Right back key 8 for approx 2 seconds Configuration mode will be terminated Measuring mode In the lower measurement value display 16 the measured value is indicated in digits In the upper measurement value display 14 the measured value is indicated in mass or CM depending on the chosen setting 1 Press the keys Right back 8 or Left menu 9 until the de sired measuring mode is displayed CFG HOLD MAX MIN AVG 13 14 15 16 The device comes with the following measuring modes Measuring mode Description ACT Measured value in real time AVG Average value of measurements since switch on MIN Minimu
19. spreading the publication Subject to technical changes All rights reserved Trademarks are used without guarantee that they may be used freely and primarily following the spelling of the manufacturer Product names are registered Changes to construction in the interests of constant improve ments to the product as well as changes to the shape and colour are reserved The scope of delivery may vary from product images This docu ment was created with all due care TROTEC accepts no liability whatsoever for possible mistakes or omissions The only party responsible for determining measured results to be valid drawing conclusions and deriving actions is the user TROTEC accepts no claims of warranty for the correctness of the determined measured values or measured results Further TROTEC accepts no liability whatsoever for possible mistakes or damage which have been caused by utilising the determined measured results TROTEC Warranty The warranty is for 12 months Damages caused by incorrect use by untrained people or start up by unauthorised people are excluded from the warranty The device complies with the fundamental health and safety requirements of the applicable EU regulations and was tested at the factory for perfect functionality multiple times However if faults in the functionality occur and cannot be remedied with the measures in the chapter Errors and faults please get in touch with your dealer or distributor Whe
20. sure that the touchscreen control panel is dirt free If required clean the touchscreen control panel according to chapter Cleaning the device on page 10 1 Hold the device pointing into clear space The device should point away from the body and not at or near material surfaces When failing to observe the above instructions the following calibration will be corrupt 2 Press the On Off key 4 until a beep is emitted The device name and firmware version is shown on the dis play The battery charge is indicated on the display The device carries out an automatic calibration During calibration the display indicates the lettering CAL These flashing characters are accompanied by brief acoustic sig nals An extended acoustic signal indicates that the calibration has been completed The device is ready for operation Operating manual Material moisture measuring device T660 D TROTEC Carrying out a measurement Note Note that moving from a cold area to a warm area can lead to con densation forming on the device s circuit board This physical and unavoidable effect can falsify the measurement In this case the display shows either no measured values or they are incorrect Wait a few minutes until the device has become adjusted to the changed conditions before carrying out a measurement Please observe the information regarding the measurement prin ciple gt 8 10 cm _ _ 5 40 m
21. ured data Besides the currently measured value can be recorded via the hold function The device further features an alarm function Once the preset limit value is exceeded the device alerts the user through emit ting an acoustic signal The device is suited for the preliminary check of the building materials readiness for covering for subsequent measurements according to the calcium carbide method CM measurement The moisture indication allows the localization of the most significant measuring spots to extract material for the CM measurement You can connect the device to a computer by using the USB cable included in the scope of delivery Then you can extract and ana lyse your measured results with the optional MultiMeasure Studio software Device depiction No Operating element Display Cross control Battery compartment with battery cover On Off key USB interface Measuring head OD om Ae ow N Cross control I ye SJ 10 A No Operating element E NN 7 Up key 8 Right back key 9 Down key 10 OK button 11 Left menu key Display er CFG 12 HOLD MAX MIN AVG 13 iP 14 cM 15 16 Y CAL 17 MAT Alarm No Display element 12 Configuration mode display 13 Measuring mode 14 Measurement value display top 15 Display of the selected unit 16 Measurem
Download Pdf Manuals
Related Search