Home

User`s Manual

1. Copyright 2014 TRENDnet All Rights Reserved Reboot your access point Administration gt Restart You may want to restart your access point if you are encountering difficulties with your access point and have attempted all other troubleshooting There are two methods that can be used to restart your access point e Turn the access point off for 10 seconds using the access point On Off switch located on the right side of your access point or unplugging the device from the power source see Product Hardware Features on page 2 Then turn the device back on either using the On Off switch or plugging the device back into the power source Use this method if you are encountering difficulties with accessing your access point management page This is also known as a hard reboot or power cycle OR e Access Point Management Page This is also known as a soft reboot or restart 1 Log into your access point management page see Access your access point management page on page 9 2 Click on Administration and click on Restart 3 Click Restart Wait for the device to reboot Reboot Click the restart button to reboot the device Restart 25 TRENDnet User s Guide TPL 410AP TPL 410APK Upgrade your access point firmware Administration gt Firmware TRENDnet may periodically release firmware upgrades that may add features or fix problems associated with your TRENDnet access point model and version
2. Password E Display Language English Preset Wireless Settings Wi Fi Name SSID Wi Fi Key Confirm Settings IP Address 192 168 10 100 MAC Address EC FO 0E 13 45 Ad Wi Fi Network Name SSID TRENDnet410_2 4GHz_9AFC Management Login Wi Fi Key 41013424EA1 http 192 168 10 100 username admin password admin 2 Enter a new password and verifv the password bv entering a second in in the Confirmed Password field Click Next Note If this is the first time accessing the access point configuration the wizard should automatically appear If the wizard does not appear automatically click Main and then Copyright 2014 TRENDnet All Rights Reserved 10 TRENDnet User s Guide TPL 410AP TPL 410APK Wireless Networking and Security How to choose the type of security for your wireless network Setting up wireless security is very important Leaving your wireless network open and unsecure could expose your entire network and personal files to outsiders TRENDnet recommends reading through this entire section and setting up wireless security on your new access point There are a few different wireless security types supported in wireless networking each having its own characteristics which may be more suitable for your wireless network taking into consideration compatibility performance as well as the security strength along with using older wireless networking hardware also called legacy hardware It
3. EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY WHETHER BASED IN CONTRACT OR TORT INCLUDING NEGLIGENCE FOR INCIDENTAL CONSEQUENTIAL INDIRECT SPECIAL OR PUNITIVE DAMAGES OF ANY KIND OR FOR LOSS OF REVENUE OR PROFITS LOSS OF BUSINESS LOSS OF INFORMATION OR DATE OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE USE PERFORMANCE FAILURE OR INTERRUPTION OF THE POSSIBILITY OF SUCH DAMAGES AND LIMITS ITS LIABILITY TO REPAIR REPLACEMENT OR REFUND OF THE PURCHASE PRICE PAID AT TRENDNET S OPTION THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE Governing Law This Limited Warranty shall be governed by the laws of the state of California Some TRENDnet products include software code written by third party developers These codes are subject to the GNU General Public License GPL or GNU Lesser General Public License LGPL Go to http www trendnet com gpl or http www trendnet com Download section and look for the desired TRENDnet product to access to the GPL Code or LGPL Code These codes are distributed WITHOUT WARRANTY and are subject to the copyrights of the developers TRENDnet does not provide technical support for these codes Please go www gnu org licenses gpl txt or http www gnu org licenses Igpl txt for specific terms of each license EITHER IN FACT OR BY OPERATION OF LAW STATUTORY OR
4. FIW AC 100 240V 200mA 50 60Hz This device complies with Part 15 of FCC rules CE Made in China MAC Address Powerline Device Password Hardware amp Firmware Version Front View gun 44 Power PWR LED emm Powerline PL LED S we Ethernet Connection ETH LED Sync Reset Button zi keng Ethernet Port Copyright 2014 TRENDnet All Rights Reserved Side View Sync Reset see the section Using the Sync Button for instructions A 4 Power Prong SCH Initiate Sync Connection and generate random network name key PWR LED will start blinking Sync Push hold for 3 seconds Note The secondary or additional Powerline adapter s Sync button must also be pushed within 2 minutes 120 sec of pushing the Sync button on the first adapter in order to establish connectivity then release Reset Push Hold for 20 seconds Reset device to factory defaults All LEDs will turn off and turn back on Note Will reset to the factory default private then release network name HomePlug AV TRENDnet User s Guide TPL 410AP TPL 410APK um Color Definition Power ae ee Device powered off Powerline connected Connection quality is Solid Best Green Syncing or Powerline data Blinking transmitting receiving Connection quality is Best PL eg E connected Connection quality is Powerline O Ku Powerline data transmitting receiving Blinking
5. please follow the Alternative Sync button procedure below The Alternative Sync button procedure applies to the following TRENDnet Models TPL 305E 306E 307E 310AP 401E 402E 405E Use the procedure Adapter C below to connect additional adapters Repeat the procedure Adapter C below for each additional adapter you add to your network Note The product images in the diagram below may not accurately illustrate your exact Powerline model When pushing the Sync button either the PWR or PL LED may blink to indicate that the Sync process has been activated JIE D Alternative Connect additional adapters using the Sync button mimienttuntazjjr i anni e a ia amino em ww 4 Push Syne button for 15 sec then release LEDs will turn off thenon On Adapters A or B Push Syne button for 3 sec then i release PL LED will blink Push Syne button for 2 sec then release PL LED will blink On All Adapters l 4 PL LED will tum 1 l solid when j connected Push Syne button l for 3 sec then release PL LED will blink Push Syne button F for 3 sec then release PL LED will blink On Adapters A amp B PL LED will turn solid when connected ml E es Copyright 2014 TRENDnet All Rights Reserved 34 TRENDnet User s Guide TPL 410AP TPL 410APK Powerline settings in access point management page Powerline You can also initiate the Sync process or as
6. 2004 108 EG Polish wymogami oraz pozosta ymi stosownymi postanowieniami Dyrektywy befindet 2004 108 EC et Eesti K esolevaga kinnitab TRENDnet seadme TPL 406E vastavust direktiivi pt Portugu s TRENDnet declara que este TPL 406E est conforme com os requisitos Estonian 2004 108 EU pohin uetele ja nimetatud direktiivist tulenevatele teistele Portuguese essenciais e outras disposi es da Directiva 2004 108 CE asjakohastele s tetele sl Jslovensko TRENDnet izjavlja da je ta TPL 406E v skladu z bistvenimi zahtevami in er English Hereby TRENDnet declares that this TPL 406E is in compliance with the Slovenian ostalimi relevantnimi dolo ili direktive 2004 108 ES essential requirements and other relevant provisions of Directive z 2004 108 EC Slovensky TRENDnet t mto vyhlasuje e TPL 406E spl a z kladn po iadavky a Slovak v etky pr slu n ustanovenia Smernice 2004 108 ES es Espa ol Por medio de la presente TRENDnet declara que el TPL 406E cumple con Spanish los requisitos esenciales y cualesquiera otras disposiciones aplicables o Lfi Suomi TRENDnet vakuuttaa taten etta TPL 406E tyyppinen laite on direktiivin exigibles de la Directiva 2004 108 CE Finnish 2004 108 EY oleellisten vaatimusten ja sita koskevien direktiivin muiden ehtojen mukainen el EAANViKH ME THN NAPOYZA TRENDnet AHAONEI OTI TPL 406E 2YMMOPQOOQONETAI Greek MPOZ TIZ OYZINAEIZ ANAITHZEIZ KAI TIX AOINE ZXETIKEX AIATA EIZ TH srIsvenska H rmed intygar
7. 2006 95 ES a 2009 125 ES TRENDnet vakuuttaa taten etta TPL 410AP tyyppinen laite on direktiivin 1999 5 EY 2004 108 EY 2006 95 EY ja 2009 125 EY oleellisten vaatimusten ja sita koskevien direktiivin muiden ehtojen mukainen Harmed intygar TRENDnet att denna TPL 410AP star verensst mmelse med de v sentliga egenskapskrav och vriga relevanta best mmelser som framg r av direktiv 1999 5 EG 2004 108 EG 2006 95 EG och 2009 125 EG 60 TRENDnet User s Guide TPL 410AP TPL 410APK es Cesky TRENDnet timto prohlasuje ze tento TPL 406E je ve shode se zakladnimi rt Malti Hawnhekk TRENDnet jiddikjara li dan TPL 406E jikkonforma mal htigijiet Czech po adavky a dal mi p slu n mi ustanoven mi sm rnice 2004 108 ES Maltese essenzjali u ma provvedimenti o rajn relevanti li hemm fid Dirrettiva 2004 108 EC dal Dansk Undertegnede TRENDnet erkl rer herved at f lgende udstyr TPL 406E Danish overholder de v sentlige krav og vrige relevante krav i direktiv hu Magyar Alul rott TRENDnet nyilatkozom hogy a TPL 406E megfelel a vonatkoz 2004 108 EF Hungarian alapvet k vetelm nyeknek s az 2004 108 EC ir nyelv egy b el r sainak de Deutsch Hiermit erkl rt TRENDnet dass sich das Ger t TPL 406E in German bereinstimmung mit den grundlegenden Anforderungen und den pl Polski Niniejszym TRENDnet o wiadcza e TPL 406E jest zgodny z zasadniczymi brigen einschl gigen Bestimmungen der Richtlinie
8. 8 7 Vista XP Copyright 2014 TRENDnet All Rights Reserved Special Features e Auto connects to other TRENDnet Powerline adapters e Additional Ethernet port for wired connectivity Antenna Gain e 2 4 GHz 2 x 3 dBi Wireless Output Power Receiving Sensitivity e 802 11b 17 dBm typical 76 dBm typical 11 Mbps e 802 11g 14 dBm typical 65 dBm typical 54 Mbps e 802 11n 14 dBm typical 61 dBm typical 300 Mbps Power e Input 100 240 V AC 50 60 Hz 0 2 A e Consumption 8 Watts Max Operating Temperature e 0 40 C 32 104 F Operating Humidity e Max 90 non condensing Certifications e CE e FCC Dimensions e A 65x100x55 mm 2 56 x 3 94 x 1 97 in e EU 65 x 100 x 77 mm 2 56 x 3 94 x 3 03 in e UK 65 x 100 x 70 mm 2 56 x 3 94 x 2 76 in Weight e A 153 g 5 4 oz e EU 164 g 5 8 oz e UK 168 g 5 9 o2 Warranty 3 year limited 52 TRENDnet User s Guide TPL 410AP TPL 410APK TPL 406E Standards e IEEE 802 3 e IEEE 802 3u e IEEE 802 3x e EEE 1901 HomePlug AV Device Interfaces e 1x10 100 Mbps port e Svnc reset button e LED indicators e Power Plug A North America Type B NEMA 5 15 EU European Type C CEE 7 16 UK United Kingdom Type G BS 1363 Frequency Band e 2 68 MHz Networking Distance e 5 000 sq ft home or 300 m 980 ft linear distance over electrical power lines Security e 128 Bit AES Advanced Encryption Standar
9. Address E Si e ta 20 FEM Technical E d EE 52 Change your access point login username and password sssseeesssenenzesnnenzantenzzonnanz 21 l Troubleshooting ie 54 Set your access elle ERC eh ul E 21 Change your access point IP address 22 Appendix EEN 56 Set up the DHCP server on your access point sse sssenenzznnnnnzzanennzznnrnzzannenzznnnnzzontana 23 Copyright 2014 TRENDnet All Rights Reserved TRENDnet User s Guide TPL 410AP TPL 410APK Product Overview TPL 410AP TPL 410APK Package Contents TPL 410AP package includes e 1x TPL 410AP Powerline 500 AV Wireless Access Point e Quick Installation Guide e CD ROM Utility amp User s Guide e Network cable 1 5 m 5 ft TPL 410APK package includes e 1x TPL 410AP Powerline 500 AV Wireless Access Point e 1x TPL 406E Powerline 500 AV Nano Adapter e Quick Installation Guide e CD ROM Utility amp User s Guide e 2x network cables 1 5 m 5 ft If any package contents are missing or damaged please contact the retail store online retailer or reseller distributor from which the product was purchased Copyright 2014 TRENDnet All Rights Reserved Features Powerline 500 AV Wireless Access Point TPL 410AP TRENDnet s Powerline 500 AV Wireless Access Point model TPL 410AP uses an electrical outlet to create or expand a wireless network Two Powerline adapters are needed to start a network Connect one adapter to a router and plug
10. Internet Explorer Firefox Chrome Safari Opera and will be referenced frequently in this User s Guide If you have changed the default IP address you will need to ensure that your computer is configured with IP address settings in the same subnet as the as the access point in order to access the access point management page Ex Access Point IP address changed to 192 168 0 100 255 255 255 0 example computer address 192 168 0 25 255 255 255 0 1 Plug the wireless access point into an available wall power outlet within reach of your computer s network cable 2 Connect a network cable from your wireless access point network port into your computer s network port Copyright 2014 TRENDnet All Rights Reserved 3 Assign a static IP address to your computer s network adapter in the subnet of 192 168 10 x ex 192 168 10 25 and a subnet mask of 255 255 255 0 Please refer to the Appendix on page 55 on how to assign static IP address to your computer 4 Open your web browser and go to IP address http 192 168 10 100 Your access point will prompt you for a user name and password Ce http 192 168 10 100 5 By default the user name is admin and password is admin You can also find the Password on a sticker on the side of the access point and on the label on the back of the access point Enter your Username and Password select your preferred language then click Login Note If you have cha
11. OTHERWISE INCLUDING Copyright 2014 TRENDnet All Rights Reserved 62 TRENDNET Product Warranty Registration Please take a moment to register your product online Go to TRENDnet s website at http www trendnet com register TRENDnet 206 75 Manhattan Place Torrance CA 90501 USA Copyright 2014 All Rights Reserved TRENDnet
12. TCP IP and click Properties d Then click Obtain an IP address automatically and click OK MAC OS 10 4 10 5 10 6 a From the Apple drop down list select System Preferences b Click the Network icon c From the Location drop down list select Automatic d Select and view your Ethernet connection In MAC OS 10 4 from the Show drop down list select Built in Ethernet and select the TCP IP tab In MAC OS 10 5 10 6 in the left column select Ethernet e Configure TCP IP to use DHCP 56 TRENDnet User s Guide TPL 410AP TPL 410APK In MAC 10 4 from the Configure IPv4 drop down list select Using DHCP and click the Apply Now button In MAC 10 5 from the Configure drop down list select Using DHCP and click the Apply button In MAC 10 6 from the Configure drop down list select Using DHCP and click the Apply button f Restart your computer Note If you are experiencing difficulties please contact your computer or operating system manufacturer for assistance How to configure your network settings to use a static IP address Note Please note that although the following procedures provided to follow for your operating system on configuring your network settings can be used as general guidelines however it is strongly recommended that you consult your computer or operating system manufacturer directly for assistance on the proper procedure for configuring network settings Windows 7 8 8 1 a Go into the C
13. TRENDnet att denna TPL 406E star l verensst mmelse OAHTIA 2004 108 EK Swedish med de v sentliga egenskapskrav och vriga relevanta best mmelser som framg r av direktiv 2004 108 EG fr Francais Par la presente TRENDnet d clare que l appareil TPL 406E est conforme French aux exigences essentielles et aux autres dispositions pertinentes de la directive 2004 108 CE Lit italiano Con la presente TRENDnet dichiara che questo TPL 406E conforme ai Italian requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 2004 108 CE Latviski Ar o TRENDnet deklar ka TPL 406E atbilst Direkt vas 2004 108 EK Latvian butiskajam prasibam un citiem ar to saistitajiem noteikumiem Lietuviy Siuo TRENDnet deklaruoja kad Sis TPL 406E atitinka esminius Lithuanian reikalavimus ir kitas 2004 108 EB Direktvvos nuostatas rl Nederlands Hierbij verklaart TRENDnet dat het toestel TPL 406E in overeenstemming Dutch is met de essenti le eisen en de andere relevante bepalingen van richtlijn 2004 108 EG Copyright 2014 TRENDnet All Rights Reserved 61 TRENDnet User s Guide Limited Warranty Limited Warranty TRENDnet warrants its products against defects in material and workmanship under normal use and service for the following lengths of time from the date of purchase TPL 410AP TPL 410APK 3 Years Warranty AC DC Power Adapter Cooling Fan and Power Supply carry 1 year warranty If a pro
14. To check if there is a firmware upgrade available for your device please check your TRENDnet model and version using the link http www trendnet com downloads In addition it is also important to verify if the latest firmware version is newer than the one your access point is currently running To identify the firmware that is currently loaded on your access point log in to the access point click on the Administrator section and then on the Status The firmware used by the access point is listed at the top of this page If there is a newer version available also review the release notes to check if there were any new features you may want or if any problems were fixed that you may have been experiencing Note When upgrading through the access point management page of the TPL 410AP both wireless access point and powerline firmware functionality can be updated using the firmware bin file This is the recommended method If you would like to upgrade the powerline firmware only you can upgrade the powerline functionality using the Powerline Utility If you have the TPL 410APK which includes the TPL 406E adapter the powerline firmware can only be updated using the Powerline Utility 1 If a firmware upgrade is available download the firmware to your computer 2 Unzip the file to a folder on your computer Please note the following e Do not interrupt the firmware upgrade process Do not turn off the device or press the Reset button d
15. Using this setting can increase throughput However it can also Wireless Advanced Settings increase error rate in some installations due to increased sensitivity to ae Gating Index radio frequencv reflections g 9 Half OFuli o Full Using this setting can help to decrease the error rate in wireless Aggregation 8 Enable ODisable data transmission and receiving i e Aggregation This setting allows you to enable the aggregation feature to HE SERIO Ie 50000 increase overall wireless throughput bv sending more frames in a single ma l Aggration Min Size 32 66 wireless transmission and decreasing the frame overhead Enabling this feature mav increase performance however in busv wireless environments this mav WMM Disable Enable decrease your overall performance as the percentage of data loss may increase in busy environment It may be best to keep this option at its default setting Coexistence Disable Enable o Enable Enables or turns on the aggregation feature o Disable Disables or turns off the aggregation feature e Aggregation Frames Allows you to specify the maximum number of aggregation frames that can be sent in a single wireless transmission e Aggregation Size Allows you to specify the maximum size of each aggregation frame Bytes to be sent in a single wireless transmission e Aggregation Min Size Allows you to specify the minimum size of each aggregation frame to be sent in a single wirel
16. a Connection quality is Better Powerline connected Connection quality is Solid Good Powerline data transmitting receiving Blinking Connection quality is Good N A Off Powerline isnot synced or connected Powerline is not synced or connected soi 10 20 Mbps 100 200Mbps oli Half Full Duplex connected ETH Green Ethernet Connection 10 20 Mbps 100 200Mbps Half Full Duplex data transmitting receiving Port disconnected no Ethernet link Note Powerline PL LED color indicates the strength and quality of the Powerline connection through the electrical system Note The following factors may affect the Powerline network s connection quality e Noise Generated by appliances which use your electrical system e g Microwaves ovens blow dryer iron dishwasher etc The quality of your household electrical wiring may also cause additional noise on your electrical system e Distance Long lengths of electrical wiring through your electrical system between connected Powerline adapters Blinking Copyright 2014 TRENDnet All Rights Reserved Power Saving TPL 406E The device will automatically reduce power usage when the connected device via Ethernet is powered off unplugged or inactive for more than 5 minutes The device will return to active mode when the connected device via Ethernet is powered on and the link is active Note TPL 406E This device offers EU compliant Standby mode f
17. from obtaining higher performance and data rates Allowing 802 11b or 802 11g devices to connect to an 802 11n capable wireless network may degrade the wireless network performance below the higher performance and data rates of 802 11n Wireless devices that only support 802 11b or 802 11g will not be able to connect to a wireless network that is set to 802 11n only mode Wireless devices that only support 802 11b will not be able to connect to a wireless network that is set to 802 11g only mode 802 11 Mode Mixed 802 11n 802 119 and 802 11b 802 11b only 802 11g only a02 11n only Mixed 602 119 and 802 11b Mixed 802 11n and 602 119 e Channel Width Select the appropriate channel width for your wireless network This setting only applies to 802 11n For greater 802 11n performance select 20 40MHz Auto Options 20MHz or 20 40MHz Auto It is recommended to use the default channel bandwidth settings Note Please note that this setting may provide more stability than the higher channel bandwidth settings such as 20 40MHz Auto for connectivity in busy wireless environments where there are several wireless networks in the area e HT20 MHz This mode operates using a single 2OMHz channel for wireless devices connecting at 802 11n on both 2 4GHz and 5GHz This setting may provide more stability than 20 40MHz Auto for 16 TRENDnet User s Guide TPL 410AP TPL 410APK connectivity in busy wireless environments w
18. in the utility 1 In the Powerline Utility Map View window select one of the Powerline adapters listed under Remote Device No of Local Devices 1 No of Remote Devices 2 Network Type Private Remote Device s Device Name Password Quality Rate Mbps MAC Address Device 1 JIUD Z EA 00 14 D1 A3 85 37 Device 2 No Pa 00 20 16 2A 16 06 2 Click Rename 3 Inthe New Name field enter the new name for the GEES ege Device Current Name Device 1 New Name Current Name Device 1 New Name John s Room 5 To rename the adapter that is immediately connected to your computer move your computer to a different adapter and restart the process listed above Copyright 2014 TRENDnet All Rights Reserved Upgrade Powerline Firmware Note The firmware can only be upgraded when your computer is directly connected to the Powerline adapter Ethernet port also called network port using an Ethernet cable also called network cable The Device Password DPW is not required when upgrading the firmware 1 To check if firmware updates are available for your Powerline adapter check your Powerline model http www trendnet com downloads 2 Save the zipped firmware file zip and extract the file to your computer 3 Make sure you connect your computer with the utility installed is directly connected to the Powerline adapter using an Ethernet cable also called network cable when upgrading the devic
19. your new access point IP address will use the following format using your new IP address http new ipaddress here to access your access point management page Setting Saved Your changes have been saved The device must be rebooted for the changes to take effect You can reboot now or you can continue to make other changes and reboot later Save Continue 22 TRENDnet User s Guide TPL 410AP TPL 410APK Set up the DHCP server on your access point Main gt DHCP Server Your access point can be used as a DHCP Dynamic Host Configuration Protocol server to automatically assign an IP address to each computer or device on your network The DHCP server is disabled by default on your access point In most cases your network router has a built in DHCP server that is typically enabled and used as your network DHCP server If you already have a DHCP server on your network leave this settings disabled 1 Log into your access point management page see Access your access point management page on page 9 2 Click on Main and click on DHCP Server 3 Review the DHCP Server settings Click Save Settings to save settings Enable Check to enable or uncheck to disable the DHCP server IP Pool Starting Address Enter the starting IP address for the DHCP server range e g 192 168 10 200 Pool Size Enter the maximum number of address the DHCP server is able to distribute e g 50 the DHCP server will issue 192
20. your access point management page see on page 9 2 Click on Status and click on Information System Information e Firmware Version The current firmware version your access point is running e Build Day The build day and time of the current firmware version your access point is running e System Up Time The duration your access point has been running continuously without a restart power cycle hard or soft reboot or reset General Firmware Version v1 10 Build Day Tue Dec 17 18 59 22 CST 2013 system Up Time Powerline Interface e MAC Address The MAC address of your access point s powerline interface configuration Powerline Interface MAC Address EC FO 0E 13 45 A7 Copyright 2014 TRENDnet All Rights Reserved Ethernet Information e IP Address The current IP address settings assigned to your access point e Subnet Mask The current subnet mask assigned to your access point e Default Gateway The current gateway assigned to your access point e MAC Address Displays the current Ethernet wired interface MAC address Ethernet IP Address 197 168 10 100 Subnet Mask 255 255 255 0 Default Gateway 192 168 10 100 MAC Address EC F0 0E 13 45 A4 Wireless LAN e Wireless OP Mode Displays the current wireless mode e Name SSID Displays the current wireless network name assigned to your access point e Channel Displays the current wireless channel your access poin
21. your computers or network devices 4 After the additional Powerline adapter is connected and installed to your computer or network device wait for the Powerline PL LED to turn on After the Powerline PL LED turns on verify that the Power PWR LED is on the Powerline PL LED is on or blinking and the Ethernet Connection ETH LED or if multiple ports LEDs 1 2 3 etc is on or blinking Note To verify that your Powerline adapters are connected successfully to your network you can check if the computer s or network device s can access the Internet through your Powerline network To install additional Powerline adapters in other rooms repeat the steps above for each adapter Copyright 2014 TRENDnet All Rights Reserved 30 TRENDnet User s Guide TPL 410AP TPL 410APK Securing your Powerline Network Powerline networks consist of two or more Powerline devices connected together using the same encryption key TRENDnet Powerline adapters automatically connect to each other over a secure encrypted signal and share the same encryption key Default encryption key HomePlugAV In order for your Powerline devices to connect to the same Powerline network the same encryption key must be assigned to all Powerline devices in that network Powerline devices that are not assigned the same encryption key will not be able to connect to the Powerline network For additional security TRENDnet recommends changing adapter d
22. 00 Mbps Wireless N Wireless Coverage Expanded wireless coverage with MIMO antenna technology Pre Encrypted For your security the wireless is pre encrypted with a unique password One Touch Connection Securely connect wireless devices at the touch of the Wi Fi Protected Setup WPS button Compatibility Compatible with legacy 2 4 GHz Wireless devices Maximum wireless signal rates are referenced from IEEE 802 11 theoretical specifications Actual data throughput and coverage will vary depending on interference network traffic building materials and other conditions 500 Mbps is the maximum physical Powerline data rate Data throughput may vary by circuit wire condition overheads Maximum of 8 adapters nodes recommended for streaming video across your network XXX Powerline networking is limited to the same electrical system Power strips GFCI outlets and AFCI circuit breakers may degrade Powerline signals Copyright 2014 TRENDnet All Rights Reserved Product Hardware Features TPL 410AP Device Label Product Model Serial Number a Ti ota JEU or JUK C ce came ZE HIW vil OR AC 100 240V 50 60Hz 0 2A FCC ID XUSTPL4104P Wi Fi Name SSID TRENDnetd18 2 4GHz XXXIX Wi Fi Key 41020000008 Management login http 192 166 10 168 Webusername admin Web password admin DPW XXXX XXXAX XXQOX XOQUX MAC Address Hardware Version Wi Fi Network Name SSID Wi Fi Securitv Kev Device Managemen
23. 168 10 200 250 Note The Start IP and End IP specify the range of IP addresses to automatically assign to computers or devices on your network Release Time Enter the DHCP lease time in seconds Note The DHCP lease time is the amount of time a computer or device can keep an IP address assigned by the DHCP server When the lease time expires the computer or device will renew the IP address lease with the DHCP server otherwise if there is no attempt to renew the lease the DHCP server will reallocate the IP address to be assigned to another computer or device Copyright 2014 TRENDnet All Rights Reserved DHCP Setup Enable IP Pool Starting mg Address 132 168 10 200 Pool Size Release Time 4 To save changes click Save When prompted to Save or Continue vou can click Save to applv the changes or click Continue to additional changes in the access point management page before saving Setting Saved four changes have been saved The device must be rebooted for the changes to take effect fou can reboot now or you can continue to make other changes and reboot later Save Continue 23 TRENDnet User s Guide Access Point Maintenance amp Monitoring Reset your Access Point to factory defaults Administration gt Reset You may want to reset your access point to factory defaults if you are encountering difficulties with your access point and have attempted all other troubleshooting Before you reset
24. Finish to dose this wizard Press Page Down to see the rest of the agreement Copvright c 1999 2005 NetGroup Politecnico di Torino Italy Copyright c 2005 2010 CACE Technologies Davis California Copyright c 2010 2013 Riverbed Technology San Francisco California All rights reserved Redistribution and use in source and binary forms with or without modification are permitted provided that the following conditions are met 1 Redistributions of source code must retain the above copyright notice this list of conditions and the following disclaimer 2 Redistributions in binarv farm must reproduce the above copyright notice this list of e If you accept the terms of the agreement dick I Agree to continue You must accept the agreement to install WinPcap 4 1 3 Mullsaft Install System v2 46 Copyright 2014 TRENDnet All Rights Reserved oF TRENDnet User s Guide TPL 410AP TPL 410APK 8 At the Powerline Configuration Utility installation window click Next 10 At the Confirm installation window click Next ja TRENDnet Powerline Utility 5 9 99 9 a x ja TRENDnet Powerline Utility 771 E 7E Welcome to the TRENDnet Powerline Utility Setup Confirm Installation Wizard er The installer will guide you through the steps required to install TRENDnet Powerline Utility on your The installer is ready to install TRENDnet Powerline Utility on your computer Compuber Click Nest ta start th
25. S 10 4 1 Apple Menu gt System Preferences gt Network 2 From the Show menu select Built in Ethernet 3 On the Ethernet tab the Ethernet ID is your MAC Address In MAC OS 10 5 10 6 1 Apple Menu gt System Preferences gt Network 2 Select Ethernet from the list on the left 3 Click the Advanced button 3 On the Ethernet tab the Ethernet ID is your MAC Address 57 TRENDnet User s Guide TPL 410AP TPL 410APK How to connect to a wireless network using the built in Windows utility Note Please note that although the following procedures provided to follow for your operating system on configuring your network settings can be used as general guidelines however it is strongly recommended that you consult your computer or operating system manufacturer directly for assistance on the proper procedure for connecting to a wireless network using the built in utility Windows 7 8 8 1 1 Open Connect to a Network by clicking the network icon fall or We in the notification area 2 In the list of available wireless networks click the wireless network you would like to connect to then click Connect 4 You may be prompted to enter a security key in order to connect to the network 5 Enter in the security key corresponding to the wireless network and click OK Windows Vista 1 Open Connect to a Network by clicking the Start Button o and then click Connect To 2 In the Show list click Wireless 3 I
26. See Product Hardware Features on page 2 e Make sure your computer in which you are installing the utility is connected to your network and your Powerline adapters are also connected to your network e Ifyou have changed your encryption key using the Sync button and you are creating a customized encryption key it is required to reset all Powerline devices to factory defaults using the physical Reset button on your Powerline adapter first before using the utility See Product Hardware Features on page 2 e Please ensure that your Powerline adapters are already installed and connected and the Ethernet port on each adapter is connected to a device powered on Powerline Utility System Requirements e Windows 8 1 32 64 bit 8 32 64 bit Windows 7 32 64 bit Vista 32 64 bit or XP 32 64 bit e Microsoft NET Framework 2 0 installed Included with CD installation Software Installation Copyright 2014 TRENDnet All Rights Reserved Software Installation 1 Insert the included CD ROM into your computer s CD ROM drive 2 At the CD Autorun Prompt window click Run Autorun exe Note If the Autorun prompt does not appear automatically open the CD contents and double click Autorun exe 3 At the CD ROM main menu click Install Utility Install Utility 4 You may receive the following prompt about WinPcap Click OK to continue the installation Note The Powerline Configuration Utility requires the us
27. TPL 406E s network port and then to your router Management Login http 192 168 10 100 username admin password admin Copyright 2014 TRENDnet All Rights Reserved TRENDnet User s Guide TPL 410AP TPL 410APK Connect additional wired devices to your network Connect one of the available LAN ports labeled 1 amp 2 on the access point to your router using an Ethernet cable You can connect additional computers or other network enabled devices to your network by using Ethernet cables to connect them to your access point Check the status of the LED indicators 1 2 on the front panel of your access point to ensure the physical cable connection from your router and your computers or devices Note If you encounter issues connecting to your network there may be a problem with your computer or device network settings Please ensure that your computer or device network settings also called TCP IP settings are configured to obtain IP address settings automatically also called dynamic IP address or DHCP and to Obtain DNS Server address settings automatically Network Storage IE N MT Copyright 2014 TRENDnet All Rights Reserved TRENDnet User s Guide TPL 410AP TPL 410APK Configure your Wireless Access Point Access your access point management page Note Your access point management page default IP address http 192 168 10 100 is accessed through the use of your Internet web browser e g
28. To save changes click Save When prompted to Save or Continue you can click Save to apply the changes or click Continue to additional changes in the access point management page before saving Setting Saved Your changes have been saved The device must be rebooted for the changes to take effect You can reboot now or you can continue to make other changes and reboot later You can completely turn off or turn on the powerline functionality by clicking the Turn Off button or Turn On button Powerline Interface 35 TRENDnet User s Guide TPL 410AP TPL 410APK Using the Powerline Utility The Powerline Utility allows you to do the following e Create a customized encryption key for your Powerline network and apply it to multiple Powerline adapters at the same time e View the Powerline adapters connected to your network using the MAC address and the approximate connection quality and speed of each Powerline adapter e View and upgrade Powerline adapter firmware Note Link speed displayed in the utility of your Powerline adapters to another through your electrical system is estimated Actual link speed may vary Before installing and using the utility please ensure the following e Write down the Device Password DPW 16 digit characters A Z only and MAC Address 12 digit characters a f A F 0 9 of each Powerline adapter as this will be required to change the encryption key for multiple Powerline adapters
29. User s Guide TRENDNET TPL 410AP Powerline O AV Wireless Access Point TPL 410APK Powerline 500 Wireless Kit TPL 410AP TPL 410APK TRENDnet User s Guide Table of Contents Contents Access Point Maintenance amp Monitoring ss sssesenenzesenenezezenenenznen 24 L Reset your Access Point to factory defaults ncicsziuncssevosnivionscicanisantupssnaptensanctewnsonsttesvonsse 24 Product OV CRG WW sisirain E E 1 Access Point Default Settings mesirii erzzzontisittajanziejnjeiiin jet di enti resi dnirdakz az 24 Package Contents sarri anen E ea EE SEE A S E a 1 Backup and restore your access point configuration settinge 25 Su TT 1 Reboot your access en 25 Product Hardware FeatureS essssssesssresssssrrssssrresssrrresssreresssrrresssereesserresssereessseersese 2 o Upgrade your access point firmware sssssssssessssereesssreresssreresssreressererossreressereresseeee 26 TP nr P e ATE E EE AE AEEA 2 l SE E 4 Check the access point system information EEN ES Application Diagram eccsccccsssscccsssssecsssssescssssssesssssssssssesessssssvssssssesssssssessssssesesssucsesasevcesen 5 Wireless Chent LSE scoucsascacsaesusceccsasiacsuegerancaesausuheceoustanedadenvageaceanaed aeergariontaviauestedeiaeien 28 l P ine Device l E 28 Expanding a HOME Network iiss cccncssscsvssescetcensesstensevectesnesecnewvertetenness 6 SE View your access point log 28 Be E a AE E A T a A tA 7 Connect additional wired devices to your netwo
30. ae re ee E or Set All Devices Only the device attache is compu e vice Gite e Isolates this computer from others Set Local Device OR Set Local Device ALL devices whose password has been entered They communicate together but are isolated from devices with a Set Remote Device s different network name Changes the encryption key for the Powerline adapter listed as the Local Device on the adapter on the Main window Encryption Key Multicast Address Set Multicast address for the selected local device This will reboot the device Encryption key for your Powerline network Note If you change the encryption key for the Powerline adapter Local Device this will disconnect the Local Device Powerline adapter from the Powerline network Note The default encryption key is HomePlugAV If you have used the Sync button to change and generate a random encryption key Unknown Networkname will be displaved Device Setup Section lii EC FO 0E 13 45 A7 MAC QCA7420 1 1 1 1190 01 20130729 FINAL Set Remote Device s Changes the encryption key for all or multiple Powerline adapters connected to your Powerline network Note Please make sure you have added Multicast Address and entered the DPW for all Powerline Click Set to synchronize adapters in your Powerline network the multicast address on before applying this setting If you do all adapters in the same not the encryption key will not change powerline ne
31. age 2 For connecting additional WPS supported devices repeat this process for each additional device 14 TRENDnet User s Guide TPL 410AP TPL 410APK PBC Software Virtual Push Button Wireless gt Wi Fi Protected Setup In addition to the hardware push button located physically on your access point the access point management page also has push button which is a software or virtual push button you can click to activate WPS on your access point 1 Log into your access point management page see on page 9 2 Click on Wireless and click on Wi Fi Protected Setup 3 To add a wireless device to your network under the section Add Wireless Device next to Virtual Push Button click Start PBC in the access point management page Add Wireless Device Virtual Push Button Start PBC 5 Within 2 minutes push the WPS button on the wireless device consult wireless device s User s Guide for length of time you are connecting The wireless connection between the wireless client device and you r access point will automatically be established Copyright 2014 TRENDnet All Rights Reserved PIN Personal Identification Number Wireless gt Wi Fi Protected Setup If your wireless device has WPS PIN typically an 8 digit code printed on the wireless device product label or located in the wireless device wireless software utility you can use this method 1 Log into your access point management page s
32. asjakohastele s tetele Hereby TRENDnet declares that this TPL 410AP is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC 2004 108 EC 2006 95 EC and 2009 125 EC Por medio de la presente TRENDnet declara que el TPL 410AP cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999 5 CE 2004 108 CE 2006 95 CE 2009 125 CE y ME THN NAPOYZATRENDnet AHAONEI OTI TPL 410AP VMMOPOONETAI MPO TI OYZIOAEIZ ANAITHZEIZ KAI TI AOINE2 2XETIKEX AIATA EIZ TH2 OAHTIAZ 1999 5 EK 2004 108 EK 2006 95 EK 2009 125 EK kat Par la pr sente TRENDnet d clare que l appareil TPL 410AP est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999 5 CE 2004 108 CE 2006 95 CE 2009 125 CE et Con la presente TRENDnet dichiara che questo TPL 410AP conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999 5 CE 2004 108 CE 2006 95 CE e 2009 125 CE ArsoTRENDnetdeklar ka TPL 410AP atbilstDirektivas 1999 5 EK 2004 108 EK 2006 95 EK un 2009 125 EK butiskajamprasibam un citiemar to saistitajiemnoteikumiem Copyright 2014 TRENDnet All Rights Reserved Lietuviy Lithuanian rl Nederlands Dutch rt Malti Maltese bul Magyar Hungarian ell Polski Polish Portugu s Portuguese sl Slovensko Slovenian Slovensky S
33. ayed How can I access the access point management page Answer Assign your computer a static IP address in the subnet of 192 168 10 x ex 192 168 10 25 and access the access point using the default IP address 192 168 10 100 http 192 168 10 100 Q typed http 192 168 10 100 in my Internet Browser Address Bar but an error message says The page cannot be displayed How can l access the access point management page Answer 1 Check your hardware settings again See Basic Installation on page 7 2 Make sure the LAN port you are connected to is on 3 Make sure your network adapter TCP IP settings are set to Obtain an IP address automatically or DHCP see the steps below 4 Make sure your computer is connected to one of the access point s LAN ports 5 Press on the factory reset button for 15 seconds the release Windows 7 a Go into the Control Panel click Network and Sharing Center b Click Change Adapter Settings right click the Local Area Connection icon c Then click Properties and click Internet Protocol Version 4 TCP IPv4 d Then click Obtain an IP address automatically and click OK Windows Vista a Go into the Control Panel click Network and Internet b Click Manage Network Connections right click the Local Area Connection icon and click Properties c Click Internet Protocol Version TCP IPv4 and then click Properties d Then click Obtain an IP address automatically and click OK Windo
34. be found on the sticker on the side of the access point or on the device label at the bottom of the access point security Mode Wireless Security Settings Preset Wireless Settings Mode OPEN Shared Auto Wi Fi Name SSID ARA ANN R NN RN Primary Key Key 1 E Wi Ky Key 1 XXXXXXXXXXXX http 92 168 10 100 username admin password admin Key 3 ooo00000000 Key 4 ooodoo0000 e Mode Choose Open Shared or Both Note It is recommended to use Auto which includes both Open and Shared Open is known to be more secure than Shared Key e Primary Key Select the key index 1 4 to use 1 Log into your access point management page see Access your access point management page on page 9 2 Click on Wireless and click on Security Note Please note that the key index number also must match the setting on the wireless client devices you are connecting 3 Click on the Security Mode drop down list to select your wireless security type e Key 1 4 Next to the Key number you select for the Primary Key enter the WEP key This is the password or key that is used to connect your computer to this access point wirelessly You can enter a 64 bit or 128 bit key Note It is recommended to use 128 bit because it is more secure to use a key that consists of more characters WEP Key Format HEX I asc Character set 0 9 amp A F a f only Alphanumeric a b C 1 2 etc Review the wireless security settin
35. ce support for all TRENDnet products Products that are sent to TRENDnet for RMA service must have the RMA number marked on the outside of return packages and sent to TRENDnet prepaid insured and packaged appropriately for safe shipment Customers shipping from outside of the USA and Canada are responsible for return shipping fees Customers shipping from outside of the USA are responsible for custom charges including but not limited to duty tax and other fees WARRANTIES EXCLUSIVE IF THE TRENDNET PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE THE CUSTOMER S SOLE REMEDY SHALL BE AT TRENDNET S OPTION REPAIR OR REPLACE THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE INSTALLATION MAINTENANCE OR USE OF TRENDNET S PRODUCTS TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER S OR ANY THIRD PERSON S MISUSE NEGLECT IMIPROPER INSTALLATION OR TESTING UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE OR BY ACCIDENT FIRE LIGHTNING OR OTHER HAZARD LIMITATION OF LIABILITY TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO
36. consoles and Internet cameras e Modem Connects a computer or router to the Internet or ISP Internet Service Provider e Router Connects multiple devices to the Internet e Switch Connect several wired network devices to your home network Your router has a built in network switch the LAN port 1 4 If you have more wired network devices than available Ethernet ports on your router you will need an additional switch to add more wired connections How to expand a home network Wireless Access Points add or extend wireless connectivity to an existing network Integrated Powerline technology allows you to further extend your network using your existing electrical system in your home using multiple powerline adapters Where to find more help In addition to this User s Guide you can find help below www trendnet com support documents downloads and FAQs are available from this Web page Copyright 2014 TRENDnet All Rights Reserved BU IBAA d all TPL 4 10AP HomePlug AV or IEEE 1901 compliant Ethernet Ethernet Ethernet Cable DSL Modem Wireless Router Media Center TRENDnet User s Guide TPL 410AP TPL 410APK Basic Installation 5 Once you have successfully connected the powerline adapters through the electrical system you can move the TPL 410AP to the desired location to create or extend Note It is recommended to plug the adapters into nearby outlets before installing the wirel
37. d Utility OS Compatibility e Windows 8 1 8 7 Vista XP Special Features e Auto connects to other TRENDnet Powerline adapters Power e Input 100 240 V AC 50 60 Hz 0 1 A o Consumption Active mode 3 Watts max Standby mode 0 5 Watts max Operating Temperature e O 40 C 32 104 F Copyright 2014 TRENDnet All Rights Reserved Operating Humidity e Max 95 non condensing Certifications e CE e FCC Dimensions e A 70x50x43 mm 2 76 x 1 97 x 1 69 in e EU 70x 50 x 63 mm 2 76 x 1 97 x 2 48 in e UK 70x50 x 58 mm 2 76 x 1 97 x 2 28 in Weight e A 51g 1 8 oz e EU 56 7 g 2 0 o2 e UK 68 g 2 4 02 Warranty 3 year limited Maximum wireless signal rates are referenced from IEEE 802 11 theoretical specifications Actual data throughput and coverage will vary depending on interference network traffic building materials and other conditions 500 Mbps is the maximum physical Powerline data rate Data throughput may vary by circuit wire condition Maximum of 8 adapters nodes recommended for streaming video across your network Powerline networking is limited to the same electrical system Power strips GFCI outlets and AFCI circuit breakers may degrade Powerline signals 53 TRENDnet User s Guide TPL 410AP TPL 410APK Troubleshooting Q typed http TPL 410AP in my Internet Browser Address Bar but an error message says The page cannot be displ
38. d e Rx Rate Displays the receive rate your powerline device has established Powerline Link Status Remote Device Tx Rate Mbps Rx Rate Mbps 00 14 D1 A3 85 37 358 323 Copyright 2014 TRENDnet All Rights Reserved View your access point log Status gt System Log Your access point log can be used to obtain activity information on the functionality of your access point or for troubleshooting purposes 1 Log into your access point management page see Access your access point management page on page 9 2 Click on Status and click on System Log Note Log messages display the date time type and additional information for each entry 1969 12 31 22 52 29 Informational hostapd ath STA dBreb 37 23 5c 39 IEEE 80 1969 12 31 22 52 29 Informational hostapd athd STA dB eb 97 23 5c 39 IEEE DO ey 28 TRENDnet User s Guide TPL 410AP TPL 410APK Installing your Powerline Adapters Before you Install 1 Before you proceed with the installation verify the following e You already have a router already installed e You already have Internet access through your existing network e An Ethernet port also called LAN port is available on your router e Verify that you have at least two Powerline adapters You will need at least two Powerline adapters to create a Powerline network Note The TPL 410AP package only includes a single Powerline adapter The TPL 410APK package includes TPL 406E an
39. d TPL 410AP to create your Powerline network Please ensure that your other Powerline adapter is HomePlug AV or IEEE 1901 compliant e g TRENDnet models TPL 303E TPL 304E TPL 305E TPL 306E TPL 307E TPL 308E TPL 310AP TPL 401E TPL 402E TPL 405E TPL 4052E TPL 406E TPL 407E TPL 408E TPL 420E or another TPL 410AP 2 Plan the location of where you will install your Powerline adapters e Avoid plugging the adapters into power strips extension cords or surge protectors as this may prevent the adapter from functioning correctly or degrade performance e Avoid plugging the adapters into wall power outlets that are controlled by a light switch to prevent the Powerline adapter from being turned off accidentally e Avoid plugging the adapters into wall power outlets that are located near appliances that consume a lot of power e g refrigerators washers dryers as this may degrade performance e Make sure there is an available wall power outlet in the room where the router is installed and also near the router e Make sure there is an available wall power outlet in the room where you want to extend network connectivity Copyright 2014 TRENDnet All Rights Reserved Connect a Powerline adapter to your router 1 Plug the Powerline adapter into an available wall power outlet near your router Note This will allow devices connected to your Powerline network to access the Internet and other devices connected to your net
40. dditional Powerline networks above the recommended may result in significant degradation in Powerline performance Powerline Group 1 Powerline Group 2 Encryption Key key1 Encryption Key key2 Adapter A eee eee Electrical Wiring mm Electrical Wiring Powerline Group 1 Powerline Group 2 58 TRENDnet User s Guide TPL 410AP TPL 410APK Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV t
41. duct does not operate as warranted during the applicable warranty period TRENDnet shall reserve the right at its expense to repair or replace the defective product or part and deliver an equivalent product or part to the customer The repair replacement unit s warranty continues from the original date of purchase All products that are replaced become the property of TRENDnet Replacement products may be new or reconditioned TRENDnet does not issue refunds or credit Please contact the point of purchase for their return policies TRENDnet shall not be responsible for any software firmware information or memory data of customer contained in stored on or integrated with any products returned to TRENDnet pursuant to any warranty There are no user serviceable parts inside the product Do not remove or attempt to service the product by any unauthorized service center This warranty is voided if i the product has been modified or repaired by any unauthorized service center ii the product was subject to accident abuse or improper use iii the product was subject to conditions more severe than those specified in the manual Warranty service may be obtained by contacting TRENDnet within the applicable warranty period and providing a copy of the dated proof of the purchase Upon proper submission of required documentation a Return Material Authorization RMA number will be issued An RMA number is required in order to initiate warranty servi
42. e The default encryption key assigned to TRENDnet Powerline adapters is HomePlugAV Before changing the default encryption please ensure that your Powerline adapters are already installed and connected using the default encryption key See Installing your Powerline Adapters on page 29 Important Note When using the Sync Button to change the default encryption key it is highly recommended to plug the adapters into nearby outlets first and follow the Sync button procedure before installing the adapters in the desired locations 31 TRENDnet User s Guide TPL 410AP TPL 410APK The Sync button procedure below applies to the following TRENDnet models TPL 303E 304E 308E 4052E 406E 407E 410AP 408E 420E Note The product images in the diagram below may not accurately illustrate your exact Powerline model When pushing the Sync button either the PWR or PL LED may blink to indicate that the Sync process has been activated z Push Syne button for 3 sec then release PL LED will blink Copyright 2014 TRENDnet All Rights Reserved P E E EE E E E EE EE E E E EE E E E E E Push Syne button E for 3 sec then release PL LED will blink On Adapters A amp B PL LED will turn solid when connected 32 TRENDnet User s Guide TPL 410AP TPL 410APK Add adapters using the Sync button If you have changed the default encryption key assigned to your adapters additional adapters wil
43. e Basic Administration o Enable Disable Wireless e Time Settings o Wireless Network Name SSID p d e asswor Channel O S e Firmware O ode o Upgrade Firmware o Channel Width e Restart Soft Reboot o Enable Disable SSID Broadcast e Reset Reset to Factory Default e Advanced l e Backup Restore e Security e Wi Fi Protected Setup WPS o PBC Push Button o PIN e MAC Filters o Backup configuration to file o Restore configuration from file Powerline e Setup o Enable Disable Powerline o Change Powerline Encryption Key e Sync o Virtual Powerline Sync Button Copyright 2014 TRENDnet All Rights Reserved 51 TRENDnet User s Guide TPL 410AP TPL 410APK Technical Specifications TPL 410AP Standards e IEEE 802 3 e IEEE 802 3u e IEEE 802 3x e IEEE 802 3az e IEEE 802 11b e IEEE 802 11g e EEE 802 11n up to 300 Mbps e IEEE 1901 HomePlug AV Device Interface e 2x 10 100 Mbps ports e Sync reset button e WPS button e Power switch e LED indicators e Power Plug A North America Type B NEMA 5 15 EU European Type C CEE 7 16 UK United Kingdom Type G BS 1363 Frequency Band e 2 68 MHz Networking Distance e Powerline 5 000 sq ft home or 300 m 980 ft linear distance over electrical power lines Security e Wireless encryption up to WPA2 e Powerline encryption 128 bit AES Advanced Encryption Standard Utility OS Compatibility optional e Windows 8 1
44. e Port Enter the port your RADIUS server is configured to use for RADIUS authentication Note It is recommended to use port 1812 which is typical default RADIUS port Secret Enter the shared secret used to authorize your access point with your RADIUS server 13 TRENDnet User s Guide TPL 410AP TPL 410APK Connect wireless devices to your access point A variety of wireless network devices can connect to your wireless network such as e Gaming Consoles e Internet enabled TVs e Network media players e Smart Phones e Wireless Laptop computers e Wireless IP cameras Each device may have its own software utility for searching and connecting to available wireless networks therefore you must refer to the User s Manual Guide of your wireless client device to determine how to search and connect to this access point s wireless network See the Appendix on page 55 for general information on connecting to a wireless network Copyright 2014 TRENDnet All Rights Reserved Connect wireless devices using WPS WPS Wi Fi Protected Setup is a feature that makes it easy to connect devices to your wireless network If your wireless devices support WPS you can use this feature to easily add wireless devices to your network Note You will not be able to use WPS if you set the SSID Broadcast setting to Disabled or if you are using WEP or WPA security Please note that WPS functionality will only be available when usin
45. e firmware 49 TRENDnet User s Guide TPL 410AP TPL 410APK 4 Launch the Powerline Utility by double clicking the icon TRENDnet Powerline Utility 5 Click on the Advanced section in the left hand panel and in the Upgrade Firmware section click Upgrade Selected Local Device EC sFO 0E 13 45 24 744AC OCA 420 1 1 1 1190 01 20130729 FINAL Upgrade Firmware Upgrade firmware for the selected local device Reset Device Reset selected local device Factory Defaults Reset selected local device with factory default settings QoS Settings Set VLAN Tags Set TOS Bits Copyright 2014 TRENDnet All Rights Reserved 6 Navigate to the unzipped folder with the firmware files and select the NVM file Ex TPL 410AP NVM v1 1 1 1190 01 X FINAL nvm Important Note Please make sure to select the correct firmware file 7 Navigate to the unzipped folder with the firmware files and select the PIB file Ex TPL 410AP PIB v1 1 1 1190 01 pib Important Note Please make sure to select the correct firmware file Wait until the firmware upload completed and the device reboot Important Do not turn off the device or press the reset button while this procedure is in progress 50 TRENDnet User s Guide TPL 410AP TPL 410APK Access Point Management Page Structure Main Status e Wizard e Information e Network Settings e DHCP Server Optional e Wireless e Powerline e System Log Wireless
46. e installation WARNING This computer program is protected by copyright law and international treaties Unauthorized duplication or distribution of this program or any portion of it may result in severe civil or criminal penalties and will be prosecuted ta the maximum extent possible under the law 9 At the License Agreement window select Agree to accept the terms and click Next 18 TRENDnet Powerline Utility rel eeng License Agreement B Select Installation Folder Please take a moment ta read the license agreement now IF you accept the terms below click I The installer will install TRENDnet Powerline Utility ta the following folder Agree then Nest Othenwse click Cancel To install in this folder click Next Ta install ta a different folder enter it below or click Browse Qualcomm Atheros Ine Software License Agreement Folder PLEASE READ THIS SOFTWARE LICENSE AGREEMENT LICENSE K C Program Files TRENDnet TRENDnet Powerline Utility CAREFULLY BEFORE USING THE QCA SOFTWARE BY USING THE QCA SOFTWARE YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE IF YOU DO NOT AGREE TO THE TERMS OF THIS LICENSE DO NOT USE THE Install TRENDnet Powerine Utility for yourself or for anyone who uses this computer SOFTWARE IF YOU DO NOT AGREE TO THE TERMS OF THE LICENSE YOU MAY RETURN THE QCA SOFTWARE TO THE PLACE WHERE YOU E O Everyone Do Not Agree Just me Copyright 2014 TRENDnet All Rig
47. e of the WinPcap application If you are prompted to install the WinPcap application continue through the following steps to complete the installation Otherwise if you are not prompted to install WinPcap reboot your computer to complete the installation WinP cap Software version 4 1 2 or higher is either not installed or some previous version Is already installed on this workstation The WinPcap version 4 1 3 installer is being launched Please follow the instructions for installing the WinP cap software 36 TRENDnet User s Guide TPL 410AP TPL 410APK 5 At the WinPcap installer window click Next 7 In the Install Options window leave the option Automatically start the WinPcap WinPcap 4 13 Setup driver at boot time checked and click Install Wait for the installation to complete Welcome to the WinPcap 4 1 3 i D P Installation options Setup Wizard JW cap Please review the following options before instaling WinPcap L3 This Wizard will guide you through the entire WinPcap installation For more information or support please visit the WinPcap home page http jaww winpcap 0rg 7 After the process is completed click Finish p WinPcap 4 1 3 Setup i WinPcap 4 1 3 Setup Completing the WinPcap 4 1 3 Setup Wizard WinPcap 4 1 3 has been installed on your computer A IV ap Please review the license terms before installing WinPcap 4 1 3 Click
48. eate a customized encryption key Copyright 2014 TRENDnet All Rights Reserved To create a customized encryption key 1 In the Powerline Utility Device Setup window under Private Network Name enter the new encryption key for your Powerline network Private Network Name TRENDnet OR Use Default Public Network Do not share the network name with others you do not want to be a part of this network 2 After you have entered your new Powerline encryption key click Set Remote Device s After setting the name above choose how it will be applied below Place On This Network Only the device attached to this computer the Local Device Isolates this computer from others ALL devices whose password has been entered They communicate together but are isolated from devices with a different network name 3 Click OK If successful you will receive a message indicating that all Powerline adapters were added to your network verifying that the encryption key was changed for all Powerline adapters Click OK Note The field will not display your customized encryption key For security purposes the field will display UnknownNetworkname Set All Devices 48 TRENDnet User s Guide TPL 410AP TPL 410APK To rename the Powerline adapters Note Renaming the Powerline adapters Remote devices to describe the location of the device will help you to easily identify which Powerline adapter you are monitoring
49. echnician for help FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired Operation For product available in the USA Canada market only channel 1711 can be operated Selection of other channels is not possible This device and it s antennas s must not be co located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi transmitter product procedures IMPORTANT NOTE FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with minimum distance 20cm between the radiator amp your body RoHS This product is ROHS compliant Copyright 2014 TRENDnet All Rights Reserved Europe EU Declaration of Conformity This device complies with the essential requirements of the R amp TTE Directive 1999 5 EC 2004 108 EC 2006 95 EC and 2009 125 EC Regulation EC No 1275 2008 EN 55022 2010 AC 2011 Class B EN 55024 2010 EN 61000 3 2 2006 A2 2009 EN 61000 3 3 2008 CISPR IXX CDV Op
50. ected For example if the first wireless client that connects to your wireless network uses WPA encryption your wireless network will use WPA encryption Only when all wireless clients disconnect to the network and a wireless client with WPA2 encryption connects your wireless network will then change to WPA2 encryption Copyright 2014 TRENDnet All Rights Reserved Note WPA2 encryption supports 802 11n speeds and WPA encryption will limit your connection speeds to 54Mbps e WPA2 This is the most secure wireless encryption available today similar to WPA encryption but more robust This encryption standard also supports the highest connection speeds TRENDnet recommends setting your access point to this encryption standard If you find that one of your wireless network devices does not support WPA2 encryption then set your access point to either WPA or WPA Auto encryption Note Check the specifications of your wireless network adapters and wireless appliances to verify the highest level of encryption supported Below is brief comparison chart of the wireless security types and the recommended configuration depending on which type you choose for your wireless network Security Standard IEEE 802 11b g 802 11n devices will operate at 802 11g to connect using this standard IEEE 802 11b g 802 11n devices will operate at 802 11g to connect using this standard Compatible Wireless Standards Highest Performance Under This Se
51. ed to reset your access point to default all your customized settings would be lost and would require you to manually reconfigure all of your access point settings instead of simply restoring from a backed up access point configuration file To backup your access point configuration 1 Log into your access point management page see Access your access point management page on page 9 2 Click on Administration and click on Backup Restore 3 Next to Save Settings to Local Hard Drive section click Save Configuration save Settings to e Local Hard Drive SE 4 Depending on your web browser settings you may be prompted to save a file specify the location or the file may be downloaded automatically to the web browser settings default download folder Default Filename tp 410cfg dat To restore your access point configuration 1 Log into your access point management page see Access your access point management page on page 9 2 Click on Administration and click on Backup Restore 3 Next to Load Settings From Local Hard Drive depending on your web browser click on Browse or Choose File EE Local Hard Drive TOWSE 4 A separate file navigation window should open 5 Select the access point configuration file to restore and click Restore Default Filename tp 410cfg fi dat If prompted click Yes or OK Wait for the access point to restore settings Restore Configuration From Restore File
52. ee on page 9 2 Click on Wireless and click on Wi Fi Protected Setup 3 To add a wireless device to your network under the section Add Wireless Device next to Client PIN enter the wireless device s 8 digit numeric PIN in the field and click Start PIN in the access point management page Note You may need to initiate the WPS PIN on your wireless device first when using this method Refer to your wireless device documentation for details on the operation of WPS Add Wireless Device Virtual Push Button Start PBC 5 Within 2 minutes initiate the WPS PIN method on the wireless device consult wireless device s User s Guide for how to initiate the WPS method you are connecting he wireless connection between the wireless client device and you r access point will automatically be established 15 TRENDnet User s Guide TPL 410AP TPL 410APK Basic Wireless Settings Wireless gt Basic This section outlines available management options under basic wireless sub tab 1 Log into your access point management page see on page 9 2 Click on Wireless and click on Basic 3 Review the basic wireless settings and click Save when finished When prompted to Save or Continue you can click Save to apply the changes or click Continue to additional changes in the access point management page before saving Setting Saved Your changes have been saved The device must be rebooted for the changes t
53. efault encryption key to prevent a neighbor with a Powerline adapter and the same default encryption key from gaining access to your network Note After the default encryption key has been changed and the Powerline adapters have been connected using a new encryption key the Powerline adapters will retain their security settings when they are unplugged and moved to a new location No additional reconfiguration of the Powerline adapters is needed after the default encryption has been changed There are two methods to change the default encryption key e Use the physical Sync button on your Powerline adapter to generate a random encryption key See Using the Sync Button on page 31 Racommended method OR e Create a customized encryption key for your Powerline network using the included Powerline Utility See Using the Powerline Utility on page 35 IF users first use the Sync button method the adapters will need to be reset to factory defaults in order to change setting using the Powerline Utility Copyright 2014 TRENDnet All Rights Reserved Using the Sync button Change your default encryption key using the Sync button The physical Sync button on the Powerline adapter provides an easy method of changing the default encryption key The Sync button generates a random encryption key for your Powerline network To create a customized encryption key see Using the Powerline Utility on page 35 Not
54. ess connectivity to your existing network devices to the desired locations Note If you are connecting the adapters to a third party powerline device other than TRENDnet and encounter issues please refer to the manufacturer s documentation for the appropriate sync button procedure 6 For added security the TPL 410AP has been pre configured with a unique wireless network name SSID and wireless key which can be found on the Preset Wireless Settings sticker or device label Use these settings to connect your wireless laptops Note The sync button procedure steps below demonstrate using TRENDnet powerline mobile devices and other wireless network devices to your network model TPL 406E included with the Powerline 500 Wireless Kit only but the same procedure applies to TRENDnet powerline models TPL 303E 304E 308E 4052E 407E 408E 420E Move TPL 410AP to the desired location and connect your wireless network devices Connecting the adapters using Powerline Internet TPL 406E TPL 410AP k Push Sync button for 3 Push Sync button for 3 i seconds then release PWR seconds then release PL l Power LED will blink Power Line LED will blink TPL 406E TPL 410AP PL Power mm PL Power Line LED will Line LED will turn solid turn solid when when connected connected Preset May take May take Wireless Settings over one over one Wi Fi Name SSID 1 Connect a network cable to the Wi Fi Key
55. ess transmission Copyright 2014 TRENDnet All Rights Reserved 19 TRENDnet User s Guide TPL 410AP TPL 410APK MAC Address Filters Wireless gt MAC Filters Every network device has a unique 12 digit MAC Media Access Control address Using MAC filters you can allow or deny specific computers and other devices from using this access point s wireless network 1 Log into your access point management page see on page 9 2 Click on Wireless and click on MAC Filters 3 Review the basic wireless settings and click Save when finished When prompted to Save or Continue you can click Save to apply the changes or click Continue to additional changes in the access point management page before saving Setting Saved Your changes have been saved The device must be rebooted for the changes to take effect You can reboot now or you can continue to make other changes and reboot later First click the MAC Filter Policy drop down list to choose the MAC filter function then click Save e Disabled disables the MAC address filter e Allow Listed MAC Addresses Only Allow computers devices with MAC addresses listed to wirelessly connect to the access point Deny all others e Deny Listed MAC Addresses Only Deny computers devices with MAC addresses listed to wirelessly connect to the access point Allow all others Note MAC filter can be configured to allow access to the listed MAC address and deny a
56. g WPA2 security There are two methods the WPS feature can easily connect your wireless devices to your network e Push Button Configuration PBC method e RECOMMENDED Hardware Push Button method with an external button located physically on your access point and on your client device e WPS Software Virtual Push Button located in access point management page e PIN Personal Identification Number Method located in access point management page Note Refer to your wireless device documentation for details on the operation of WPS Recommended Hardware Push Button PBC Method e Note It is recommended that a wireless key passphrase or password is created before connecting clients using the PBC method By default your access point is preconfigured with a wireless encryption key If no wireless key is defined when connecting via PBC the access point will automatically create an encryption key that is 64 characters long This 64 character key will then have to be used if one has to connect computers to the access point using the traditional connection method To add a wireless device to your network simply push the WPS button on the wireless device you are connecting consult client device User s Guide for length of time then push and hold the WPS button located on your access point for 3 seconds and release it The PWR LED will blink to indicate WPS has been activated on your access point See Product Hardware Features on p
57. g the access point on or near metal objects such as file cabinets and metal furniture reflective surfaces such as glass or mirrors and masonry walls c Any obstruction can weaken the wireless signal even non metallic objects so the fewer obstructions between the access point and the wireless device the better d Place the access point in a location away from other electronics motors and fluorescent lighting e Many environmental variables can affect the access point s performance so if your wireless signal is weak place the access point in several locations and test the signal strength to determine the ideal position 2 Building materials can have a large impact on your wireless signal In an indoor environment try to position the wireless devices so that the signal passes through less dense material such as dry wall Dense materials like metal solid wood glass or even furniture may block or degrade the signal 3 Antenna orientation can also have a large impact on your wireless signal Use the wireless adapter s site survey tool to determine the best antenna orientation for your wireless devices Copyright 2014 TRENDnet All Rights Reserved 4 Interference from devices that produce RF radio frequency noise can also impact your signal Position your wireless devices away from anything that generates RF noise such as microwaves radios and baby monitors If possible upgrade wireless network interfaces suc
58. gs click Save when finished When prompted to Save or Continue you can click Save to apply the changes or click Continue to additional 64 bit key length changes in the access point management page before saving 128 bit key length Copyright 2014 TRENDnet All Rights Reserved Wireless Security Settings Security Mode 12 TRENDnet User s Guide TPL 410AP TPL 410APK Selecting WPA WPA2 Auto Personal Shared Key WPA2 AES recommended Note Please note that WPS will only work when using WPA2 encryption If using WPA encryption you must disable WPS feature first under Wireless gt Wi Fi Protected Setup Wireless Security Settings Security Mode WPA f Type Personal Shared Key Mode e WPAQ WPA2G Auto Encrvption TKF AES Auto PSK Key First in the Security Mode drop down list select WPA In the Type drop down list select either Personal Shared Key or Enterprise RADIUS support e Personal Shared Key Create your own personal security key Recommended e Enterprise Also called RADIUS Remote Dial In User Service Requires an external RADIUS server to authenticate clients The following section outlines options when selecting Personal Shared Key WPA WPA2 Auto Then in the Mode section select WPA WPA2 or Auto WPA2 Recommended Finally in the Encryption section select TKIP AES or Auto o When selecting WPA mode it is recommended to use TKIP encryption o When selecting WPA2 m
59. h as wireless cards in computers from older wireless standards to 802 11n or 802 11ac If a wirelessly networked device uses an older standard the performance of the entire wireless network may be slower If you are still experiencing low or no signal consider repositioning the wireless devices installing additional access points or wireless extenders 18 TRENDnet User s Guide TPL 410AP TPL 410APK Advanced Wireless Settings e WMM Wi Fi Multimedia is a Quality of Service QoS feature which prioritizes audio and video data packets This feature requires the wireless device to also Wireless gt Advanced support WMM Click Enabled recommended or Disabled to turn this feature on These settings are advanced options that can be configured to change advanced or off on your access point wireless broadcast specifications It is recommended that these settings remain set to their default values unless you are knowledgeable about the effects of changing these e Coexistence If set to Enable will not allow legacy devices such as 802 11b g to values Changing these settings incorrectly can degrade performance connect wireless This will ensure that access point will provide the best possible performance rate available If set to Disable will allow all wireless clients to connect including 802 11b g Gating Index Select the option that works best for your installation It may be best to keep this option at its default setting o Halt
60. hen release sec of pushing the Sync button on the first adapter in section order to establish connectivity Note Powerline PL LED color indicates the strength and quality of the Powerline Using the connection through the electrical system sync Button Reset Reset device to factory defaults PWR PL and WIFI LEDs Note The following factors may affect the Powerline network s connection quality ae Push Hold for 10 will turn off and turn back on to indicate reset e Noise Generated by appliances which use your electrical system e g instructions seconds Note Will reset to the factory default private network Microwaves ovens blow dryer iron dishwasher etc The quality of your then release name HomePlug AV household electrical wiring may also cause additional noise on your electrical WPS Activates WPS Wi Fi Protected Setup The PWR kid Push Hold for 3 Power LED will blink to indicate WPS has been Distance Long lengths of electrical wiring through your electrical system between seconds then release successfully activated connected Powerline adapters Copyright 2014 TRENDnet All Rights Reserved TRENDnet User s Guide TPL 410AP TPL 410APK TPL 406E Important Note Please note that the TPL 406E powerline adapter will only be included when purchasing the Powerline 500 Wireless Kit model TPL 410APK Device Label Product Model Serial Number ae No MAC XAXXXXXXAX DPW seins MFA HIW
61. here there are several neighboring wireless networks in the area e HT20 40MHz Auto When 20 40MHz Auto is active this mode is capable of providing higher performance only if the wireless devices support the channel bandwidth settings Enabling 20 40MHz Auto typically results in substantial performance increases when connecting an 802 11n client Channel Width HT20 H7T20 40 e Broadcast SSID e Enable Allows wireless devices to search and discover your wireless network name also called SSID broadcasted by your access point e Invisible Turns off the ability for wireless devices to find your network It is still possible for wireless devices to be configured to connect to your wireless network Disabling this setting will disable WPS functionality Broadcast SSID Enable Disable Copyright 2014 TRENDnet All Rights Reserved 17 TRENDnet User s Guide TPL 410AP TPL 410APK Steps to improve wireless connectivity There are a number of factors that can impact the range of wireless devices Follow these tips to help improve your wireless connectivity 1 Keep the number of obstructions to a minimum Each obstruction can reduce the range of a wireless device Position the wireless devices in a manner that will minimize the amount of obstructions between them a For the widest coverage area install your access point near the center of your home and near the ceiling if possible b Avoid placin
62. hts Reserved 38 TRENDnet User s Guide TPL 410AP TPL 410APK 12 In the Completion window click Close fq TRENDnet Powerline Utility a Installation Complete TRENDnet Powerline Utility has been successfully installed Click Close to exit Cancel Back Copyright 2014 TRENDnet All Rights Reserved 39 TRENDnet User s Guide TPL 410AP TPL 410APK Using the Utility Before using the utility please ensure the following e Write down the Device Password DPW 16 digit characters A Z only and MAC Address 12 digit characters a f A F 0 9 of each Powerline adapter as this will be required to change the encryption key for multiple Powerline adapters See Product Hardware Features on page 2 e Make sure your computer in which you are installing the utility is connected to your network and your Powerline adapters are also connected to your network e Ifyou have changed your encryption key using the Sync button and you are creating a customized encryption key it is required to reset all Powerline devices to defaults using the physical Reset button on your Powerline adapter first before using the utility See Product Hardware Features on page 2 e Please ensure that your Powerline adapters are already installed and connected and the Ethernet port on each adapter is connected to a device powered on Upon completing the software installation a desktop shortcut is automatically created Double c
63. in the TPL 410AP on your electrical system to create or expand a high performance wireless network Powerline 500 Wireless Kit TPL 410APK TRENDnet s Powerline 500 Wireless Kit model TPL 410APK uses electrical outlets to create a hybrid Powerline Wireless network The included TRENDnet Powerline adapters TPL 406E TPL 410AP auto connect out of the box Network the TPL 406E to a router and plug the TPL 410AP into an outlet on the electrical system to extend a high performance wireless network Hardwire a smart TV gaming console or media player to the two Ethernet ports on the TPL 410AP Powerline Auto Connect Powerline Simply plug in the Powerline adapters all TRENDnet adapters auto connect out of the box Sync Button Press the Sync button to change existing Powerline encryption keys Pre Encrypted For your security the Powerline signal is pre encrypted Powerline 500 High speed Powerline networking over existing electrical lines Ethernet Ports Two convenient Ethernet ports to hardwire computers smart TVs and other network enabled devices Cross Compatible TRENDnet Powerline 500 and 200 adapters work together TRENDnet User s Guide TPL 410AP TPL 410APK Whole Home Coverage Connects over electrical lines for houses up to 5000 square foot home 300 m 984 ft linear distance over electrical lines Wireless Quick Setup Get up and running in minutes with the intuitive guided setup N300 Wireless Proven 3
64. is strongly recommended to enable wireless security to prevent unwanted users from accessing your network and network resources personal documents media etc In general it is recommended that you choose the security type with the highest strength and performance supported by the wireless computers and devices in your network Please review the security types to determine which one you should use for your network Wireless Encryption Types e WEP Legacy encryption method supported by older 802 11b g hardware This is the oldest and least secure type of wireless encryption It is generally not recommended to use this encryption standard however if you have old 802 11 b or 802 11g wireless adapters or computers with old embedded wireless cards wireless clients you may have to set your access point to WEP to allow the old adapters to connect to the access point Note This encryption standard will limit connection speeds to 54Mbps e WPA This encryption is significantly more robust than the WEP technology Much of the older 802 11g hardware was been upgraded with firmware driver upgrades to support this encryption standard Total wireless speeds under this encryption type however are limited to 54Mbps e WPA Auto This setting provides the access point with the ability to detect wireless devices using either WPA or WPA2 encryption Your wireless network will automatically change the encryption setting based on the first wireless device conn
65. isplays the current device time and date information You can click Sync with host to force the device to check for updated date and time information with the NTP server configured in the NTP server setting Current Time Wed Dec 31 19 34 27 GMT 1969 Sync with host e Location Time Zone Click the drop down list and select your time zone Location GMT 08 00 Pacific Time e NTP Server Your access point will update the date and time settings by synchronizing with an NTP Network Time Protocol server address e g pool ntp org Enter the NTP server address next to Default NTP server e g pool ntp org Note NTP servers are used for computers and other network devices to synchronize time across an entire network NIP Server us pool ntp org e NTP Sync Cycle You can set the interval in hours when you access point will synchronize with the NTP server NTP Sync Cycle 21 TRENDnet User s Guide TPL 410AP TPL 410APK Change your access point IP address Main gt Network Settings Typically the access point IP address settings only needs to be changed when connecting the access point to your network and configuring to the device to be in the same IP network as your existing network Default Access Point IP Address Settings 192 168 10 100 255 255 255 0 1 Log into your access point management page see Access your access point management page on page 9 2 Click on Main and click on Netw
66. l LEDs will turn off then turn back on This will reset the Powerline adapters to their default settings The default encryption key is HomePlugAV The Powerline adapters can provide better connectivity and performance when plugged directly into a power outlet Connecting the Powerline adapters to a power strip or surge protector may degrade or block Powerline signals Copyright 2014 TRENDnet All Rights Reserved TPL 410AP TPL 410APK e Avoid using the Powerline adapters on GFI protected outlets and electrical systems with AFCI circuit breakers They may degrade or block Powerline signals e The Powerline adapters should not be used in areas with excessive heat e Florescent and incandescent lighting can generate significant Powerline interference e Ifvourbuilding has more than one circuit breaker box the Powerline adapter may not be able to establish connectivity between them In this case connect a Powerline adapter into a power outlet located on each of the circuit breaker boxes Then connect an Ethernet cable between the Powerline adapters to bridge the two circuits together In addition to this User s Guide you can find help below e http www trendnet com support documentation downloads FAQs how to contact technical support e Autorun CD Quick Installation Guide 55 TRENDnet User s Guide TPL 410AP TPL 410APK Appendix How to find your IP address Note Please note that although the follo
67. l not automatically connect to your Powerline network after they are plugged into a wall power outlet For any additional adapters you will need to use the Sync button to connect any additional adapters to use the same encryption key of your existing Powerline network Use the procedure Adapter C below to connect additional adapters Repeat the procedure Adapter C below for each additional adapter you add to your network The Sync button procedure below applies to the following TRENDnet models TPL 303E 304E 308E 4052E 406E 407E 410AP 408E 420E Note The product images in the diagram below may not accurately illustrate your exact Powerline model When pushing the Sync button either the PWR or PL LED may blink to indicate that the Sync process has been activated _ Connect additional adapters using the Sync button Push Syne button for 3 sec then PL LED will blink Push Syne button release will Blin for 3 sec then release PL LED will blink On Adapters A or B Push Syne button for 3 sec then release PL LED will blink Push Syne button for 3 sec then release PL LED will blink On Adapters A amp B PL LED will turn solid when connected On All Adapters PL LED will turn solid when connected Copyright 2014 TRENDnet All Rights Reserved JA TRENDnet User s Guide TPL 410AP TPL 410APK If adding a TRENDnet adapter models Adapter C not listed in the previous page
68. lick the icon to start the utility or open the utility if it is already running Closing the utility will exit the application TRENDnet Powerline Utilitv You can also launch the utility from the Start Menu programs Start gt Programs or All Programs gt TRENDnet gt TRENDnet Powerline Utility TRENDnet 41 TRENDnet Powerline Utility Gei TRENDnet Powerline Utility Copyright 2014 TRENDnet All Rights Reserved 40 TRENDnet User s Guide TPL 410AP TPL 410APK Powerline Utility Overview MAC Address Local Device Map View Window x 7 Firmware Version Map View Section Local Device Local Device Version MACACA 420 1 1 1 1190 01 20 MAC Address A Local Devices Local Device hum QCA 420 ei Device Setup a Advanced d Options The Powerline adapter connected to your router d Selected QCA7420 EC FO0 0E 13 45 47 Auto Scan enabled Note If your computer is connected directly to l vour Powerline ae No of Remote Devices 1 Network Type Private adapter the Local Remote Device s Device listed will be the l Device Name Password Quality Rate Mbps MAC Address EE Device 1 No Pa OU 381 00 14 D1 A3 85 37 computer is directly connected to 1 1 1 1 Device Device Connection Speedor MAC Remote Devices Name Password Qualitv Link Rate Address Powerline adapters in DPW remote locations that are connected to the selected Powerline adapter L
69. ll others unlisted or vice versa The recommended function is to choose to only allow access to the MAC addresses listed and deny all others unlisted because it is easier to determine the MAC addresses of devices in your network then to determine which MAC addresses you do not want to allow access Copyright 2014 TRENDnet All Rights Reserved MAC Filtering Policy Policy Disabled e Allow Listed MAC Addresses Deny Listed MAC Addresses Add the MAC addresses to the MAC Address List first Click Save to add each entry to the MAC Address List e MAC Address Check the box next to the entry to enable and in the empty field enter the MAC address of the devices you would like to filter e g 00 11 22 AA BB CC e Comment Enter a short description of the MAC address to help you to easily identify it Add MAC Address Comment Note If you wireless clients are currently connected you can check Status gt Wireless to find the MAC address If you device is not listed please refer to your computer or device documentation to find the MAC address In the MAC Address List you can click Delete All to delete all MAC addresses in the list or select the specific MAC address entry under the Se ect column and click Delete to delete a specific entry MAC Address List MAC Address Comment Select No MAC Addresses Listed 20 TRENDnet User s Guide TPL 410AP TPL 410APK Change your access point login username and
70. lovak Lti suomi Finnish L svenska Swedish iuo TRENDnet deklaruoja kad is TPL 410AP atitinka esminius reikalavimus ir kitas 1999 5 EB 2004 108 EB 2006 95 EB ir 2009 125 EB Direktyvos nuostatas Hierbij verklaart TRENDnet dat het toestel TPL 410AP in overeenstemming is met de essenti le eisen en de andere relevante bepalingen van richtlijn 1999 5 EG 2004 108 EG 2006 95 EG en 2009 125 EG Hawnhekk TRENDnet jiddikjara li dan TPL 410AP jikkonforma mal ti ijiet essenzjali u ma provvedimenti o rajn relevanti li hemm fid Dirrettiva 1999 5 KE 2004 108 KE 2006 95 KE u 2009 125 KE Alul rott TRENDnet nyilatkozom hogy a TPL 410AP megfelel a vonatkoz alapvet6 k vetelm nyeknek s az 1999 5 EK ir nyelv a 2004 108 EK a 2006 95 EK s a 2009 125 EK ir nyelv egy b eldirasainak Niniejszym TRENDnet oswiadcza ze TPL 410AP jest zgodny z zasadniczymi wymogami oraz pozostatymi stosownymi postanowieniami Dyrektywy 1999 5 WE 2004 108 WE 2006 95 WE i 2009 125 WE TRENDnet declara que este TPL 410AP esta conforme com os requisitos essenciais e outras disposi es da Directiva 1999 5 CE 2004 108 CE 2006 95 CE e 2009 125 CE TRENDnet izjavlja da je ta TPL 410AP v skladu z bistvenimi zahtevami in ostalimi relevantnimi dolo ili direktive 1999 5 ES 2004 108 ES 2006 95 ES in 2009 125 ES TRENDnettymtovyhlasuje Ze TPL 410AP splfazakladn po iadavkv a vsetkyprisluSn ustanoveniaSmernice 1999 5 ES 2004 108 ES
71. n the list of available wireless networks click the wireless network vou would like to connect to then click Connect 4 Vou mav be prompted to enter a securitv kev in order to connect to the network 5 Enter in the securitv kev corresponding to the wireless network and click OK Windows XP 1 Right click the network icon in the notification area then click View Available Wireless Networks 2 In Connect to a Network under Available Networks click the wireless network you would like to connect to 3 You may be prompted to enter a security key in order to connect to the network 4 Enter in the security key corresponding to the wireless network and click Connect Copyright 2014 TRENDnet All Rights Reserved Overlapping Powerline networks It is possible to create multiple Powerline networks on the same electrical system separated and grouped by different network encryption keys The Powerline networks will work and communicate independently of each other which can provide security between different groups of Powerline adapters For example if you have five powerline adapters Adapter A Adapter B Adapter C Adapter D Adapter E you can group Adapters A B and C together on one powerline network and group Adapters D and E on a different Powerline network Each group will use a different encryption key Note It is recommended that only a maximum of up to 4 Powerline networks can be created per electrical system Any a
72. net All Rights Reserved Powerline Utility Overview About Window Co TRENDNET TRENDnet Version v7 1 Build 0101 Released September 05 2013 ciTRENDnet Inc All rights reserved License Copyrights Copyright c 1999 2015 NetGroup Politecnico di Torino Italy A Copyright c 2015 2009 CACE Technologies Davis California 8 All rights reserved Redistribution and use in source and binary forms with or without modification are permitte 1 Redistributions of source code must retain the above copyright notice this list of conditio 2 Redistributions in binary form must reproduce the above copyright notice this list of conc 3 Neither the name of the Politecnico di Torino CACE Technologies nor the names of its cor THIS SOFTWARE I5 PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS AS IS This product indudes software developed by the University of California Lawrence Berkele This product indudes software developed by the Kungliga Tekniska HOaskolan and its contr This product indudes software developed by Yen Yen Lim and North Dakota State Universit 46 TRENDnet User s Guide TPL 410AP TPL 410APK Add adapters in the utility and create a customized encryption key If you have not written down the Device Password DPW and MAC address for each of your Powerline adapters please do so as it is required to applying the customized encryption key for all of your Powerline adapters using the u
73. nged the password already such as in the Setup Wizard you will need to login using the new password Default User Name admin Default Password admin Note User Name and Password are case sensitive Preset Wireless Settings Wi Fi Name SSID XXXXXXXXXXXX C TPL 410AP LOGIN User Name Wi Fi Kev XXXXXXXXXXXX Management Login http 192 168 10 100 username admin password admin Password E Display Language English Login TRENDnet User s Guide TPL 410AP TPL 410APK Setup Wizard click Wizard For security purposes you are required to change the admin password during the initial setup 1 Log into your access point management page see on page 9 Set Password New Password TPL 410AP LOGIN Maximum characters is 30 User Name 3 For added security the Wi Fi Name SSID and WiFi Key or encryption key have been ee preconfigured with unique settings The wizard will list your preconfigured Wi Fi settings in the confirmation window You can also find these preconfigured settings on the A Preset Wireless Settings sticker or on the device label on the back on the device You will need to use this information to connect your wireless devices to your access point To change the Wi Fi key please refer to the section Secure your Wireless Network on page 11 If the access point is reset to factory defaults the Wi Fi Key and Wi Fi Name will reset to the preconfigured default settings
74. o take effect You can reboot now or you can continue to make other changes and reboot later e Enable Wireless LAN Interface Check the option to enable the wireless network band or uncheck to disable Note It is recommended to leave this setting checked Enable Wireless LAN Interface e Wireless Network Name SSID Enter the wireless name SSID for your wireless network This acronym stands for Service Set Identifier and is the name of your wireless network It differentiates your wireless network from others around you By default the access point s wireless name is unique to the device If you choose to change the SSID change it to a name that you can easily remember Wireless Network Name SSID Copyright 2014 TRENDnet All Rights Reserved e Channel Selecting the Auto option will set your access point to scan for which wireless channel s to use automatically Otherwise you to manually set the channel on which the access point will broadcast Click the drop down list and select the desired Channel for wireless communication The goal is to select the Channel that is least used by neighboring wireless networks Channel When applying the Mode setting please keep in mind the following e Wireless devices that support 802 11n are backwards compatible and can connect wirelessly at 802 11g or 802 11b Connecting at 802 11b or 802 118 will limit the capability of your 802 11n supported wireless devices
75. ocal Device across the electrical svstem Note If all of vour Powerline adapters are alreadv connected to vour Powerline network thev will Enter Password Add Device Scan automaticaliv detected and BS Allows you to enter the DPW Allows you to adda Rescans the Powerline appear in the list If not you Renames the for the listed Powerline Powerline adapter to adapters that are will need to add them listed Powerline adapter Remote Device your Powerline connected to your MARAE adapter THIS MUST BE ENTERED FOR Network that is not Powerline network Remote Device ALL DEVICES TO CHANGE THE listed Remote Device Remote Device ENCRYPTION CODE Copyright 2014 TRENDnet All Rights Reserved 41 TRENDnet User s Guide TPL 410AP TPL 410APK Powerline Utility Overview Detailed View Window Detailed View Section e PE olsen system Imformation Application TRENDnet Powerline Utility Version v7 1 Build 0101 Released September 05 2013 Computer Name JEREMY User Name jeremy Microprocessor 586 No of Processors 2 Operating System Windows 7 Service Pack 1 System Information Detailed View Device Setup Advanced Displays the device and other related information such as firmware version MAC address and encryption key also called network 4 password NIC 1 You can vertically scroll the window to view all of RxR the system information Remote Device History Log MAC Address Pas
76. ocal Device MAC Address Version QCA 420 BA F0 0E 13 45 A MAC QCA 420 1 1 1 1150 01 20 Local Devices Selected QCA7420 EC FO 0E 13 45 A7 Auto Scan enabled No of Local Devices 1 No of Remote Devices 2 Network Type Private Remote Device s MAC Address 00 20 16 7A4 16 06 00 14 D1 A3 85 37 Device Name Password Quality Rate Mbps Device 2 No Pa u Device 1 No Pa H 3 Select one of the Powerline adapters listed under Remote Device No of Local Devices 1 No of Remote Devices 2 Network Type Private Remote Device s Device Name Password Quality Rate Mbps MAC Address paas lilu Device 1 Pa 00 14 D1 A3 85 37 4 TRENDnet User s Guide TPL 410AP TPL 410APK 4 Click Enter Password Enter Password 5 Enter the Device Password DPW and click OK Note Match the Device Password DPW to the corresponding MAC address Set Device Password Device Device 2 Password fECC 77 C WIVY GFR5 The password typically appears as a number and letter code in group of four seperated by dashes For example XKBY SH26 BR 1K L75A Itis found on the device or packaging 6 If successful you will receive a message indicating that the password is correct Click OK Repeat steps 2 6 for each additional Powerline adapter listed in Remote Device until you have added all of your remaining Powerline adapters before continuing to the next step To cr
77. ode it is recommended to use AES encryption o When selecting Auto mode it is recommended to use AES encryption Create your WiFi Security Key PSK e PSK Key Enter the key or passphrase e Note This is the key that is used to connect your computer and other wireless client devices to your router Note 8 63 alphanumeric characters a b C 4 1 2 etc Copyright 2014 TRENDnet All Rights Reserved Selecting WPA WPA2 Auto Enterprise RADIUS Support The following section outlines options when selecting WPA Enterprise EAP or RADIUS This security type is also known as EAP Extensible Authentication Protocol or Remote Authentication Dial In User Service or RADIUS Note This security type requires an external RADIUS server Pre Shared Key only requires you to create a passphrase Type Enterprise RADIUS support Mode e 802 1x WPA WPA20 Auto Encryption TKIPO AES Auto RSN Preauth Disable Enable EAP Reauth Period Server 192 168 123 200 Port secret 1234567690 RSN Preauth Enable this feature only if your external RADIUS server and wireless client support RSN Robust Security Network Pre authentication used more commonly for wireless client roaming between multiple access points EAP Reauth Period Set the time in seconds when the wireless access point will request for re authentication from the wireless client Server Enter the IP address of the RADIUS server e g 192 168 10 250
78. ontrol Panel click Network and Sharing Center b Click Change Adapter Settings right click the Local Area Connection icon c Then click Properties and click Internet Protocol Version 4 TCP IPv4 d Then click Use the following IP address and assign your network adapter a static IP address Click OK Windows Vista a Go into the Control Panel click Network and Internet b Click Manage Network Connections right click the Local Area Connection icon and click Properties c Click Internet Protocol Version TCP IPv4 and then click Properties d Then click Use the following IP address and assign your network adapter a static IP address Click OK Windows XP 2000 a Go into the Control Panel double click the Network Connections icon b Right click the Local Area Connection icon and the click Properties c Click Internet Protocol TCP IP and click Properties Copyright 2014 TRENDnet All Rights Reserved d Then click Use the following IP address and assign your network adapter a static IP address Click OK MAC OS 10 4 10 5 10 6 a From the Apple drop down list select System Preferences b Click the Network icon c From the Location drop down list select Automatic d Select and view your Ethernet connection How to find your MAC address In Windows 2000 XP Vista 7 8 Your computer MAC addresses are also displayed in this window however you can type getmac v to display the MAC addresses only In MAC O
79. ork Settings 3 Under LAN Interface Setup review the settings e Dynamic IP Check this option to set the access point to automatically obtain IP address settings from a DHCP server Note Typically your network router has a built in DHCP server e Static IP Uncheck the Dynamic IP option to manually specify an IP address in the IP Address Subnet Mask and Default Gateway fields e IP Address Enter the new access point IP address e g 192 168 0 100 e Subnet Mask Enter the new access point subnet mask e g 255 255 255 0 e Gateway Address Enter the default gateway address of your network This parameter is required for the access point to access Internet for functions such as e mail notifications Note Typically your network router IP address is used as the default gateway address to access the Internet e g 192 168 10 1 Note Typically your network IP address is used as the DNS server address Copyright 2014 TRENDnet All Rights Reserved LAN Interface Setup Dynamic IP m IP Address 192 168 10 100 Subnet Mask 255 255 255 0 Default Gatewav 192168 10 100 4 To save changes click Save When prompted to Save or Continue you can click Save to apply the changes or click Continue to additional changes in the access point management page before saving Note You will need to access your access point management page using your new access point IP address e g Instead of using the default http 192 168 10 100
80. outdoor radio links and or for supplying public access to telecommunications and or network services This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 2483 5 MHz For detailed information the end user should contact the national spectrum authority in France 59 TRENDnet User s Guide TPL 410AP TPL 410APK cs Cesky Czech da Dansk Danish Deutsch German et Eesti Estonian en English es Espa ol Spanish EAAnvikn Greek Lft Francais French Lit Italiano Italian Latviski Latvian TRENDnet t mto prohla uje ze tento TPL 410AP je ve shod se zakladnimi pozadavky a dalsimi prislusnymi ustanovenimi smernice 1999 5 ES 2004 108 ES 2006 95 ES a 2009 125 ES Undertegnede TRENDnet erkl rer herved at f lgende udstyr TEW TPL 410AP overholder de v sentlige krav og vrige relevante krav i direktiv 1999 5 EF 2004 108 EF 2006 95 EF og 2009 125 EF Hiermit erkl rt TRENDnet dass sich das Ger t TPL 410AP in bereinstimmung mit den grundlegenden Anforderungen und den brigen einschl gigen Bestimmungen der Richtlinie 1999 5 EG 2004 108 EG 2006 95 EG und 2009 125 EG befindet K esolevaga kinnitab TRENDnet seadme TPL 410AP vastavust direktiivi 1999 5 EU 2004 108 EU 2006 95 E ja 2009 125 EU pahin uetele ja nimetatud direktiivist tulenevatele teistele
81. password Administration gt Password 1 Log into your access point management page see on page 9 2 Click on Administration and click on Password 3 In the User Name field enter the new user name and in the Password field enter the new password Then enter the password again in the Confirmed Password field to verify Password User Name New Password Maximum characters is 30 3 To save changes click Save When prompted to Save or Continue you can click Save to apply the changes or click Continue to additional changes in the access point management page before saving Setting Saved Your changes have been saved The device must be rebooted for the changes to take effect You can reboot now or you can continue to make other changes and reboot later Note If you change the access point login password you will need to access the access point management page using the User Name admin and the new password Copyright 2014 TRENDnet All Rights Reserved Set your access point date and time Administration gt Time Settings 1 Log into your access point management page see on page 9 2 Click on Administration and click on Time Settings 3 Review the Time settings Click Save to save settings When prompted to Save or Continue you can click Save to apply the changes or click Continue to additional changes in the access point management page before saving e Current Time D
82. rk 8 Installing your Powerline Adapterg EEN 23 Berore EECH 29 Configure your Wireless Access Point ssseseneneenezenenenneneneneanenenna 9 l Connect a Powerline adapter to your router ss sse eennnznnnnnnnzznnenznnzznnenznzzzznnnnnnzzna 29 Access your access point management page ssssssccccccceeseseeccceeeseeseeecceesesuessseeseees 9 Add adapters to your network cseccccccssssecceeeesseccecseesecceseueseceessauaeeeessuaaeeeessaaaeeeeees 30 Sette V2 ANd EE 10 Wireless Networking and S CULItY cccccccssssecceceeeseceeccesececesseseceessseueeeessaaaeeeesaees 11 Securing your Powerline Network EEN 31 How to choose the type of security for your wireless NetWork s 11 Using the Sync button ccecccccccssssececccesseccccaeeseceeceeeeceeseeeeecessueaseceesauneeessegaeseeesaees 31 Secure your wireless network sssssseeeenennnnnnnnnnnnnzzznznnrennzzznennnnnnzznnnnznnzznn 12 Using the Powerline Utility ccsccssscssccssccssscsssscesscessccssenecenes 36 Connect wireless devices to vour ACCESS Doint ENEE 14 Powerline Utility System Requirements ss sessensensnnzansenzansnnennennnnnnnnnznnznnznann 36 Connect wireless devices USING WS 14 Software Stall Atl OM EE 36 Basic Wireless Settings ENEE 16 Uoma the Eege 40 Steps to improve wireless CONNECTIVITY EE 18 Bee Ee Me 49 Advanced Wireless SCUUINGS issiierr ai iri tri e re a Se 19 Access Point Management Page Structure 51 MAC
83. sign a customized encryption key instead of using Powerline Utility using the access point management page Applies to TPL 410AP Access Point only To initiate the Sync process using the access point management page Powerline gt Sync 1 Log into your access point management page see on page 9 2 Click on Powerline and click on Sync 3 Click the Sync button sync User can use this page to make two PLC devices pair or use hardware push button trigger behavior Click the Sync button to activate the synchronization process and connect to another Powerline device where the synchronization process has also been activated Using the Sync button will change the default network name encryption key to a randomly generated key for additional security You can also push the hardware SYNC RESET button located on device to activate the synchronization process Copyright 2014 TRENDnet All Rights Reserved To assign a customized encryption key Powerline gt Setup Note Please note that you must use the same customized encryption key for all other powerline devices in order to establish powerline connection 1 Log into your access point management page see on page 9 2 Click on Powerline and click on Setup 3 Under Powerline Configuration enter your customized encryption key in the Network Name key field Note It is strongly recommended to keep the CCo mode at the default settings Auto 4
84. status and your IP address settings displayed Copyright 2014 TRENDnet All Rights Reserved Note If you are experiencing difficulties please contact your computer or operating system manufacturer for assistance How to configure your network settings to obtain an IP address automatically or use DHCP Note Please note that although the following procedures provided to follow for your operating system on configuring your network settings can be used as general guidelines however it is strongly recommended that you consult your computer or operating system manufacturer directly for assistance on the proper procedure for configuring network settings Windows 7 8 8 1 a Go into the Control Panel click Network and Sharing Center b Click Change Adapter Settings right click the Local Area Connection icon c Then click Properties and click Internet Protocol Version 4 TCP IPv4 d Then click Obtain an IP address automatically and click OK Windows Vista a Go into the Control Panel click Network and Internet b Click Manage Network Connections right click the Local Area Connection icon and click Properties c Click Internet Protocol Version TCP IPv4 and then click Properties d Then click Obtain an IP address automatically and click OK Windows XP 2000 a Go into the Control Panel double click the Network Connections icon b Right click the Local Area Connection icon and the click Properties c Click Internet Protocol
85. sword Tx Rate Mbps 00 14 D1 A3 85 37 Mo Password En 381 Device Device 1 Remote Device History Log Displays Powerline adapters or other Powerline devices Remote Device that have been previously connected to or discovered on your Powerline Network Copyright 2014 TRENDnet All Rights Reserved Delete Deletes or removes the selected entry listed in the Remote Device History Log Remote Device Save Report Saves the information contained in the System Information window to a text file on your computer Print Report Prints the information contained in the System Information window Show Active Device s Only Check this option to display only the currently connected powerline adapters Uncheck to display all previously connected powerline adapters 42 TRENDnet User s Guide TPL 410AP TPL 410APK Powerline Utility Overview Device Setup Window Use Default Public Network Selected Local Device Replaces the current encryption key value with the Device Setup Private Network Name default HomePlugAV Advanced f f HomePlugAy OR Use Default Public Network Note You will still need to Do not share the network name with others you do not want to be a part of this network apply the settings to your After setting the name above choose how it will be applied below ge werline adapters by clicking Set Local Device Only Place On This Network
86. t B EN 50412 2 1 2005 AC 2009 EN 62311 2008 EN60950 1 2006 A11 2009 A1 2010 A12 2011 Safety of Information Technology Equipment EN 50385 2002 Product standard to demonstrate the compliance of radio base stations and fixed terminal stations for wireless telecommunication systems with the basic restrictions or the reference levels related to human exposure to radio frequency electromagnetic fields 110MHz 40 GHz General public EN 300 328 V1 7 1 2006 10 Electromagnetic compatibility and Radio spectrum Matters ERM Wideband Transmission systems Data transmission equipment operating in the 2 4 GHz ISM band and using spread spectrum modulation techniques Harmonized EN covering essential requirements under article 3 2 of the R amp TTE Directive EN 301 489 1 V1 9 2 2011 09 Electromagnetic compatibility and Radio Spectrum Matters ERM ElectroMagnetic Compatibility EMC standard for radio equipment and services Part 1 Common technical requirements EN 301 489 17 V2 2 1 2012 09 Electromagnetic compatibility and Radio spectrum Matters ERM ElectroMagnetic Compatibility EMC standard for radio equipment Part 17 Specific conditions for 2 4 GHz wideband transmission systems 5 GHz high performance RLAN equipment and 5 8 GHz Broadband Data Transmitting Systems In Italy the end user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up
87. t URL Default User Name Default Password Powerline Device Password Made in Taiwan Front View 10 100Mbps Ethernet LAN Ports 1 2 Power PWR LED Wireless WIFI LED Powerline PL LED TRENDnet User s Guide TPL 410AP TPL 410APK Side View PWR Power Blinking WPS is activated device on or Blinking Wireless enabled data transmitting receiving off WIFI Wireless Ste Wireless disabled Solid Powerline connected Connection quality is Best Green Blinkin Syncing or Powerline data transmitting receiving Connection quality is Best WPS Button On Off Power Sync Reset Button Power Prong Solid Powerline connected Connection quality is Better PL Powerline Amber ae Powerline data transmitting receiving Connection 6 quality is Better Solid Powerline connected Connection quality is Good Powerline data transmitting receiving Connection Blinking quality is Good ina off Powerline is not synced or connected Powerline is not synced or connected 10 20 Mbps 100 200Mbps Half Full Duplex connected LAN Ports 1 2 Initiate Sync Connection and generate random network Sync name key PL LED will start blinking Ethernet Blinking 10 20 Mbps 100 200Mbps sil Push hold for 3 Note The secondarv or additional Powerline adapter s SERRESSEN Half Full Duplex data transmitting receiving seconds Sync button must also be pushed within 2 minutes 120 see the t
88. t is operating e Security Mode Displays the wireless security type applied e MAC Address The MAC address of your access point s wireless LAN or interface configuration Wireless LAN WLAN OP Mode Access Point Name SSID TRENDnet410_2 4GHz_9AFC Channel Auto Security Mode WPA MAC Address EC FO 0E 13 45 A6 2 TRENDnet User s Guide TPL 410AP TPL 410APK Wireless Client List Status gt Wireless You can view the list of active wireless devices currently connected to your access point 1 Log into your access point management page see Access your access point management page on page 9 2 Click on Status and click on Wireless You can also click Refresh to refresh the status e Address Displays the MAC address of your wireless client e Channel Displays the current channel that the wireless client is connectioned e RSSI Displays the signal strength of your wireless client e Rate Displays the current rate your wireless client has established Associated Wireless Client List Address Channel d8 eb 97 23 5c 39 1 Powerline Device List Status gt Wireless You can view the list of active powerline devices currently connected to your access point 1 Log into your access point management page see Access your access point management page on page 9 2 Click on Status and click on Powerline e Tx Rate Displays the transmission rate your powerline device has establishe
89. tility This information is on the sticker on the inside face of each adapter Note Write down the Device Password DPW 16 digit characters A Z only and MAC Address 12 digit characters a f A F 0 9 of each Powerline adapter first before proceeding Example Location of Powerline Adapter Device Password DPW MAC Address At Router ZAYB VIMV YFAQ ZFPA EC FO OE 13 45 A7 John s Room WECC ZZYC WJVY GZRS 00 20 16 2A 16 06 UXMA UOUP IQXJ UTVN 00 14 D1 A3 85 37 Note It is recommended to ensure that your Powerline adapters are already installed and connected and the Ethernet port on each adapter is connected to a device powered on Jane s Room First add all of the Powerline adapters to the utility and enter the Device Password DPW for each Powerline adapter to ensure you can change the encryption key for multiple adapters This is required when using the Powerline utility to change the encryption key for multiple Powerline adapters To add automatically detected Powerline adapters to the Powerline Utility 1 Launch the Powerline Utility TRENDnet Powerline Utility Copyright 2014 TRENDnet All Rights Reserved 2 In the Powerline Utility Map View window wait for the utility to automatically scan for Powerline adapters already connected to your Powerline network If your Powerline adapters have already been installed and connected using the same encryption key they should appear in the Remote Device list L
90. tting Up to 54Mbps EE Strength Low Open System or Shared Key HEX or ASCII Different key sizes IEEE 802 11b g n Up to 54Mbps Up to 300Mbps Medium High TKIP or AES TKIP or AES Preshared Key or Preshared Key or RADIUS RADIUS Additional Options TKIP AES Preshared Key Preshared Key 8 63 characters 8 63 characters Recommended Configuration Open System ASCII 13 characters Dependent on the maximum 802 11n data rate supported by the device 150Mbps 300Mbps 11 TRENDnet User s Guide TPL 410AP TPL 410APK Secure your wireless network Selecting WEP Wireless gt Security If selecting WEP Wired Equivalent Privacy please review the WEP settings to configure After you have determined which security type to use for your wireless network see and click Save to save the changes then click Save again to commit the changes How to choose the security type for your wireless network on page 11 you can set up Note Please note that you may receive an error message regarding WPS when wireless security attempting to set to WEP encryption WPS will not work when using WEP security and must be disabled first under Wireless gt Wi Fi Protected Setup before using WEP security Note By default your access point is configured with a predefined wireless network WPS will only work when using WPA2 encryption name SSID and security key using WPA2 Personal The predefined wireless network name and security can
91. twork for any Powerline adapters without the DPW entered Copyright 2014 TRENDnet All Rights Reserved 43 TRENDnet User s Guide TPL 410AP TPL 410APK Powerline Utility Overview Advanced Window Selected Local Device Advanced Section Upgrade Firmware Allows you to upgrade Upgrade Firmware bei devi Uparade firmware for the selected local device Upgrade the Ore kien powerline firmware Reset Device Reset selected local device s Reset Device Reboots the local Factory Defaults device Reset selected local device with factory default settings Fact Default actory DerauIts QoS Settings Resets the local device Set VLAN Tags powerline configuration to factory default Set VLAN Tags Set VLAN Tag for stream identity Set TOS Bits Set Type of Service ToS bits to differentiate packets Copyright 2014 TRENDnet All Rights Reserved 44 TRENDnet User s Guide TPL 410AP TPL 410APK Powerline Utility Overview Options Window scan Options Auto Scan be Detailed View Options Section h Device Setup 7 sec Check this option to Advanced automatically e detect scan for powerline devices Scan Interval Click the up and down arrows to set amount of time in seconds between each auto scan for powerline devices Copyright 2014 TRENDnet All Rights Reserved 45 TRENDnet User s Guide TPL 410AP TPL 410APK Device Setup z Adwanced Copyright 2014 TREND
92. unctionality To turn off the device unplug it from the power outlet Note TPL 410AP This device offers EU compliant Off mode functionality To turn off the device push the power switch into the off position lication Diagram LI la PC ming HD streaming L l J andor and or 500 sa Ss SS ema pa me em pm me mi T i 5 T I U in CH E im m D movies The first Powerline unit is networked to a router which is in turn connected to a modem typically from your Internet Service Provider ISP which provides Internet connectivity ex TPL 406E The Powerline Access Point is plugged into a wall power outlet near a media center and can allow a network game console and another network enabled media device such as a network enabled media player to connect to the Ethernet ports and provide Internet connectivity and WiFi connectivity TRENDnet User s Guide TPL 410AP TPL 410APK Expanding a Home Network What is a network A network is a group of computers or devices that can communicate with each other A home network of more than one computer or device also typically includes Internet access which requires a router A typical home network may include multiple computers a media player server a printer a modem and a router A large home network may also have a switch additional routers access points and many Internet capable media devices such as TVs game
93. uring the upgrade If you are upgrade the firmware using a laptop computer ensure that the laptop is connected to a power source or ensure that the battery is fully charged Disable sleep mode on your computer as this may interrupt the firmware upgrade process Do not upgrade the firmware using a wireless connection only using a wired network connection Any interruptions during the firmware upgrade process may permanently damage your access point Copyright 2014 TRENDnet All Rights Reserved 1 Log into your access point management page see Access your access point management page on page 9 2 Click on Administration and click on Firmware 3 Depending on your web browser next to Select File click Browse or Choose File Note In addition this page displays the access point current firmware version and build date Upgrade Firmware Firmware Version 1 10 Build Day Tue Dec 17 18 59 22 CST 2013 Select File 4 Navigate to the folder on vour computer where the unzipped firmware file bin is located and select it 5 Click Upload If prompted click Ves or OK 26 TRENDnet User s Guide TPL 410AP TPL 410APK Check the access point system information Status gt Information You may want to check the system information of your access point such as IP address settings access point mode wireless and wired network settings access point wireless MAC addresses and firmware version 1 Log into
94. ve wireless connectivity on page 18 if you continue to have wireless connectivity problems 54 TRENDnet User s Guide Please reference the items below if you continue to experience difficulty with installing and using your Powerline adapters Do not plug the Powerline adapters into a power strip Make sure to plug the adapters directly into a power outlet and not through power strip Using adapters through a power strip may negatively affect Powerline connectivity and performance Do not use the Sync button for more than 2 Powerline adapters to connect simultaneously Wait for each Powerline adapter to connect to your Powerline network one at a time before connecting the next adapter Using more than one adapter to Sync simultaneously may cause some of your adapters not to Sync and establish connection to your Powerline network Power cycle the Powerline adapters by disconnecting them from their power outlets for 15 seconds and then reconnect them If the Powerline PL LED is red try plugging the Powerline adapter into another available power outlet The quality of the connection may be better ina different power outlet If you are having issues connecting the Powerline adapters after changing the encryption key using the Sync button or Powerline utility reset the Powerline adapters to defaults using the physical Reset button Using a pin or paperclip press and hold the Reset button for 1 second on each Powerline adapter Al
95. wing procedures provided to follow for your operating system on configuring your network settings can be used as general guidelines however it is strongly recommended that you consult your computer or operating system manufacturer directly for assistance on the proper procedure for configuring network settings Command Prompt Method Windows 2000 XP Vista 7 8 8 1 1 On your keyboard press Windows Logo R keys simultaneously to bring up the Run dialog box 2 In the dialog box type cmd to bring up the command prompt 3 In the command prompt type ipconfig all to display your IP address settings MAC OS X 1 Navigate to your Applications folder and open Utilities 2 Double click on Terminal to launch the command prompt 3 In the command prompt type ipconfig getifaddr en or en1 gt to display the wired or wireless IP address settings Note en0 is typically the wired Ethernet and en1 is typically the wireless Airport interface Graphical Method MAC OS 10 6 10 5 1 From the Apple menu select System Preferences 2 In System Preferences from the View menu select Network 3 In the Network preference window click a network port e g Ethernet AirPort modem If you are connected you ll see your IP address settings under Status MAC OS 10 4 1 From the Apple menu select Location and then Network Preferences 2 In the Network Preference window next to Show select Network Status You ll see your network
96. work 2 Connect the included Ethernet cable also called network cable from the Ethernet port also called network port of your Powerline adapter to an available Ethernet port also called LAN port on your router 3 Once the Powerline adapter is installed and connected to your router verify that the Power PWR LED is on or blinking and the Ethernet Connection ETH LED or if multiple ports LEDs 1 2 3 etc is on or blinking 29 TRENDnet User s Guide TPL 410AP TPL 410APK Add adapters to your network Once you have installed and connected the first Powerline adapter to your router you can easily extend your network to other rooms by adding additional Powerline adapters To extend your network using an additional Powerline adapter 1 First make sure the first Powerline adapter is installed and connected to your router Note This will allow devices connected to your Powerline network to access the Internet and other devices connected to your network See Connect a Powerline adapter to your router on page 29 2 Plug the additional Powerline adapter into an available wall power outlet in another room near a computer or network device e g game consoles network enabled TVs network attached storage network media server players etc that you would like to connect to your network 3 Connect the included Ethernet cable from the Ethernet port on your Powerline adapter to the to the Ethernet port of
97. ws XP 2000 a Go into the Control Panel double click the Network Connections icon b Right click the Local Area Connection icon and the click Properties c Click Internet Protocol TCP IP and click Properties d Then click Obtain an IP address automatically and click OK Copyright 2014 TRENDnet All Rights Reserved Note If you are experiencing difficulties please contact your computer or operating system manufacturer for assistance Q The Wizard does not appear when I access the access point What should do Answer 1 Click on Main and Wizard on the left hand side 2 Near the top of the browser Pop up blocked message may appear Right click on the message and select Always Allow Pop ups from This Site 3 Disable your browser s pop up blocker Q I cannot connect wirelessly to the access point What should I do Answer 1 Double check that the Wireless LED on the access point is on 2 Power cycle the router Unplug the power to the access point Wait 15 seconds then plug the power back in to the access point 3 Contact the manufacturer of your wireless network adapter and make sure the wireless network adapter is configured with the proper SSID The default predefined SSID is printed on the device label on the bottom or on the sticker on the side of the unit 4 To verify whether or not wireless is enabled login to the access point management page click on Basic and Wireless 5 Please see Steps to impro
98. your access point to defaults if possible you should backup your access point configuration first see Backup and restore your access point configuration settings on page 25 There are two methods that can be used to reset your access point to factory defaults e Reset Button Located on the left side of your access point see Product Hardware Features on page 2 Use this method if you are encountering difficulties with accessing your access point management page OR e Access Point Management Page 1 Log into your access point management page see Access your access point management page on page 9 2 Click on Administration and click on Reset 3 Click the Reset button to reset your access point to factory defaults Reset When click default button system will reset to default settings Reset Copyright 2014 TRENDnet All Rights Reserved Access Point Default Settings Administrator User Name Administrator Password Access Point IP Address Access Point Subnet Mask Wireless Interface Wireless Network Name Encryption WPA2 PSK AES Powerline Encryption Key TPL 410AP TPL 410APK Please refer to sticker or device label HomePlugAV 24 TRENDnet User s Guide TPL 410AP TPL 410APK Backup and restore your access point configuration settings Administration gt Backup Restore You may have added many customized settings to your access point and in the case that you ne

User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents