Home

ARC RUNNER WELDING CARRIAGE

1. A range of a change of the working parameters is 1 to 40 and is electronically limited e To enter a programming mode of different parameters of the carriage the machine has to be stopped by toggling the travel direction switch B to 0 position then the function knob F1 has to be pressed for approx 3 seconds Following information will be displayed Weld length ipm 5 0 20 0 The machine is a programming mode of positional welding Using the F2 function knob set required value from a range 1 to 100 INFORMATION All technological parameters excluding an overall length of a weld may be set in a resolution of 0 1 or 1 To set a parameter in a resolution of 0 1 the knob has to be simultaneously pressed and turned in a required direction e Aturn of the function knob F1 in a clockwise direction causes a step into next menu Following information will appear on the display Skip lpm 5 0 20 0 The machine is in a programming mode of a length of an interval between positional welds Using F2 functional knob a required value has to be set in a range of 0 to 40 gt 12 ARC Runner 11 2011 Operations Manual for Welding Carriage INFORMATION A skip value of 0 automatically switches the machine to a continuous welding mode e Aturn of the F1 functional knob in a clockwise direction causes a step into next menu Following information will appear on the display
2. Crater fill lpm 3 0 20 0 The machine is in a programming mode of a crater filling time A required value of time has to be set in a range 0 to 3 seconds with the function knob F1 INFORMATION The time of a crater filling backweld is defaulted to a resolution of 0 1 seconds e A turn of the function knob F1 in a clockwise direction causes a step to a next menu Following information will appear on the display Backweld lpm 0 5 20 0 The machine is in a programming mode of the length of an overlap for filling craters Using the F2 functional knob set the required value for a range of 0 to 2 Basic resolution of the parameter is 0 1 e A turn of the function knob F1 in a clockwise direction will cause a step to a next menu Following information will appear on the display Total length lpm 120 20 0 The machine is in a programming mode of a total length of a travel Using the function knob F2 set a required value of a range Weld length Skip to 400 inches INFORMATION a The minimum distance of the total travel is automatically computed by the control system and equals to a sum of a length of positional weld and a length of intervals between welds b The fundamental resolution of the parameter is 10 To set the parameter in a resolution of 1 the knob has to be simultaneously pressed and turned in a required direction A setting of
3. 1 20 0 A particular setup number should be chosen by turning the function knob F2 in a range O to 40 and then pushing it to call up from memory the particular setup is recommended that a log of each setup parameter be kept for quick and easy reference The control system will confirm the transfer with a following message Load setup ipm Done 20 0 INFORMATION In this mode an operator also has a few options a Turning the function knob F2 again depending on the rotation direction increases or decreases a number of the set parameters Pushing the function knob F2 will cause a read of data again e g from another number of the set parameters The last program called into memory will be the program executed by the machine Turning the function knob F1 depending on the direction results in a step to a next or previous menu of the carriage A push and hold of the function knob F1 for approx 3 seconds results in an exit to the main menu of the carriage The machine is ready to work A turn of the function knob F1 in a clockwise direction results in a step to a procedure of saving into the carriage memory with default values In this case a following information will appear on the screen Defaults ipm Sure F2 20 0 Completion of this operation will take place after pushing the function knob F2 Pushing and holding the function knob F1 for approx 3 seconds results in a
4. 6 Clamp a torch into the torch holder and hoses into the hose holder 7 If the carriage is to ignite a torch undo the cover of the arc ignition socket and plug a cable controlling the torch to it 8 Place the carriage onto work piece 9 Adjust the guiders distance front guider in the direction of travel slid out about 10 mm less than the rear guider 10 Set the power switch to O position 11 Set the arc ignition switch to 0 position 12 Set the travel direction switch to STOP middle position 13 Plug in the power cable to an outlet 7 START UP WITHOUT ARC IGNITION 1 Toggle the power switch to I position 2 Input required parameters of work see instructions of parameters programming section 7 3 Using the travel direction switch choose desired direction of travel The carriage will begin the travel with programmed welding parameters Make sure that the guiders are correctly positioned for the direction of travel as discussed in 5 9 4 Check if travel and speed are correct if needed change the position of the guiders or the settings of torch and welding parameters 5 To stop the carriage toggle the travel direction switch to 0 position or toggle the power switch to 0 position welding parameters are saved 6 Switch the power off the power switch to O 10 ARC Runner 11 2011 Operations Manual for Welding Carriage 8 PROGRAMMING OF WELDING PARAMETERS INFORMATION a A li
5. ARC Runner 11 2011 Operations Manual for Welding Carriage 12 3 Mounting of the oscillation assembly Dismantle the torch holder 1 Dismantle the torch plate 3 by undoing four M5x10 2 bolts from the guides assembly 5 e Unscrew the oscillator connection socket cover 4 Ae a Ge e Mount the oscillator assembly 7 to the guides assembly 5 with two M5x20 bolts 6 e Connect the oscillator assembly plug 7 with the socket 8 e Mount the torch holder 1 18 ARC Runner 11 2011 Operations Manual for Welding Carriage 12 4 The oscillator programming After a establishing a correct communication with the oscillator the carriage control system enables programming of its basic parameters from the control panel This solution removes regulation potentiometers from the control panel In a present stage of the design the software does not allow a real time correction of welding parameters during its work This inconvenience will be resolved in a next design development e A turn of the function knob F1 in a clockwise direction results in a step to next menu which is related to the oscillator parameters On the display the following information will appear Mode F1 ipm Disabled 20 0 It is page intended to record one out of four parameters of the oscillator to the function button F1 e Aturn of the function knob F1 in a clockwise direction results in a step into a next menu which
6. accordance with the following standard s placed below EN 50144 1 EN 55014 and satisfies safety regulations of guidelines 2004 108 EC 2006 95 EC 2006 42 EC Bialystok 2011 10 05 Pd Wiktor Marek Siergiej Prezes 24 ARC Runner 11 2011 Operations Manual for Welding Carriage ARC Runner 15 MACHINE TEST CERTIFICATE Machine control card Serial No Date of test Electric test results Test Result Test with sinusoidal voltage of 1000 V and frequency 50 Hz Resistance of the protective circuit Q The above mentioned product meets the requirements of safe usage as prescribed in standard IEC 745 Name of tester Quality Control 25 ARC Runner 11 2011 Operations Manual for Welding Carriage 16 WARRANTY CARD WARRANTY CARD No Steelmax Tools LLC in the name of Manufacturer warrants the Drilling Machine to be free of defects in material and workmanship under normal use for a period of twelve months from date of original sale to the end user This warranty does not cover cutters damage or wear arises from misuse accident tempering or any other causes not related to defects in workmanship or material Date of Production Serial GO ande a Date of Purchases eire E a ed Dd rM EE eee Signature of Selefie ino OL 26 Runn
7. drive with no belts to replace This saves time and money compared to competitors Lightweight with compact dimensions Adhesion with permanent magnets block with the toggle switch Driving unit is self braking Travel speed control Quick clamping for different types of MIG MAG type torches Precise adjustment of the welding torch Programmable for all standard welding functions including o Speed Oscillation speed Oscillation Width Oscillation Delays Left and Right Crater Fill Backweld Stitching with full speed between stitches vary stitch length and length between stitches Crater fill for full quality weld o Does not replace welding technician but makes them more productive and increases weld quality substantially Less QC rejection saves cost no underweld Reduces weld wire and gas use by eliminating overweld 10 Forty 40 programs are available in non volatile memory o Never erased even when powered off for long periods o Easier for communication between engineering and operations Rather than detailed specifications just say use program 4 o Operator still has limited control for variations on weld wire gases base steel etc Extremely easy and intuitive to program m 0 7 0 0 Runner 11 2011 Operations Manual for Welding Carriage 4 TECHNICAL DATA ARC Runner without oscillation ARC Runner 372 300 390 mm 324 359 mm 334 409
8. is related to a configuration of the oscillator parameters On the display the following information will appear Mode F2 lpm Disabled 20 0 It is a page intended to record one out of four parameters to the function button F2 e Aturn of the function knob F1 in a clockwise direction results in a step to a next menu which is related to the configuration of the oscillator parameters On the display the following information will appear Osc ampl lpm 10 20 0 The machine is in a mode of programming the oscillation amplitude A value of 0 100 should be set with the function knob F2 A value of 0 is corresponding with no oscillation where a value of 100 is corresponding with the maximum reach of the oscillator arm The actual length of the oscillation will depend on the actual connection through various fixtures of the torch to the oscillator assembly The control system automatically stores input value and does not require a confirmation e next turn of the function knob F1 in a clockwise direction results in a step to a next menu which is related to a configuration of the oscillator parameters The following information will appear on the display 19 ARC Runner 11 2011 Operations Manual for Welding Carriage ARC Runner Osc speed ipm 10 20 0 The machine is in a mode of programming of the speed frequency of the oscillation A desired value in a range 0 10096 should be
9. 4 ARC RUNNER WELDING CARRIAGE Steelmax Tools LLC 6200 S Troy Circle Suite 110 Centennial CO 80111 1 87steelmax www steelmax com sales steelmax com FAX 303 690 9172 1 PURPOSE c 3 2 GENERAL DESIGN visicsisctsstssdassinssdesssncinnessscnccesasscnssanaccenuas 4 3 ARC RUNNER PROPERTIES 5 4 TECHNICAL Rada ranas mn nn 6 EE 12a 8 6 PREPARATION FOR WORK 10 7 START UP WITHOUT ARC IGNITION 10 8 PROGRAMMING OF WELDING PARAMETERS 11 9 WORK 14 10 ADJUSTMENT AND MAINTENANCE 14 11 PARTS LIST AND DRAWINGS 15 12 OSCILLATION ASSEMBLY OPTIONAL 16 12 1 General design of the welding carriage with oscillation 16 12 2 Technical data of the welding carriage with oscillation 16 12 3 Mounting of the oscillation assembly 18 12 4 The oscillator programming 19 12 5 The oscillator setting operation 22 13 ELECTRICAL SCHEMATIC DIAGRAM 23 14 EC DECLAR
10. ATION OF CONFORMITY 24 15 MACHINE TEST CERTIFICATE 25 15 WARRANTY 26 m ARC Runner 11 2011 Operations Manual for Welding Carriage L 1 PURPOSE The ARC Runner is a welding carriage designed to work with MIG MAG type welding torches with a grip diameter of 0 63 to 1 inch 16 25 mm It enables the production of fillet welds butt joints in a horizontal or vertical position and lap joints It enables continuous or stitch welding Optionally the carriage may produce welds with an oscillation to aid in the filling of larger spaces between sections to be welded Do not use the machine in an upside down position on the ceiling of a vessel or structure due to safety concerns It is not designed for this type of use Fitting torches other than MIG MAG type of diameters different from 16 25 mm 16 35 mm is not allowed The torch hoses should be suspended not rubbing against base material to avoid additional drag on the machine and possible hose damage Maximum weight of hoses is 26 4 Ibs 12 kg for a horizontal position and 17 6 lbs 8 kg for a vertical position Maximum reach out of its envelope 3 2 80 mm ARC Runner 11 2011 Operations Manual for Welding Carriage 2 GENERAL DESIGN The ARC Runner welding carriage is a compact c
11. EP 1 once per month ARC Runner 11 2011 Operations Manual for Welding Carriage 14 ARC Runner 11 PARTS LIST AND DRAWINGS ITEM PART NUMBER VERSION DESCRIPTION Q TY 1 PRW 0476 04 00 00 0 2397 FOLLOWER ASSEMBLY 2 2 SRB 0476 08 00 00 0 FOLLOWER SCREW 4 3 NKR 000120 SAFETY NUT 1 4 WKR 000096 SOCKET BUTTON HEAD CAP SCREW M5x10 4 5 PDK 000036 ROUND WASHER 5 5 4 6 KOL 0476 01 07 00 0 2252 DRIVE WHEEL 4 7 OSL 000036 LEVER KEY COVER 2 8 ZLP 000025 PLUG M12 SERIES713 1 9 UCW 0476 20 00 00 0 2360 TORCH HOLDING ASSY 1 9 1 ZRZ 0466 04 01 00 0 2092 TORCH CLAMP ASSY 1 9 2 TLJ 0419 04 02 03 0 INSULATION SLEEVE 1 10 UCW 0476 06 00 00 0 2073 LOW TORCH HOLDING ASSY 1 10 1 ZCS 0476 06 01 00 0 2109 CLAMPING BLOCKS 1 10 2 TLJ 0419 04 02 03 0 INSULATION SLEEVE 1 15 ARC Runner 11 2011 Operations Manual for Welding Carriage 12 OSCILLATION ASSEMBLY OPTIONAL 12 1 General design of the welding carriage with oscillation 4 Oscillator 6 Torch holder 7 Hose holder 2 Guides assembly 1 Drive unit 3 Follower 5 Control panel 9 Toggle switch 8 Wheel 12 2Technical data of the welding carriage with oscillation 372 300 390 mm 275 292 258 293 334 409 mm 16 ARC Runner 11 2011 Operations Manual for Welding Carriage ARC Runner Power supply 115 230
12. V 50 60Hz separate units due to plug interface Welding position vertical horizontal Material thickness 3 16 5 mm minimum Base material clearance 3 16 5 mm Driving system Four high temperature resistant silicone wheels with the magnetic block gear driven no belts to replace Guiding system Two roller guides in various configurations Towing force 33 7 Ft lbs 150 vertical 49 5 Ft lbs 220 horizontal Torch Top Down 1 4 in 35 mm adjustment Left Right 1 4 in 35 mm Follower adjustment 3 0 in 75 mm program start direction left Travel direction switch stop program start direction right Function button F1 The carriage A change of technological parameter controller Function button F2 nw Value change Arc ignition switch TEST 0 1 Speed knob 0 47 2 in min 0 1200 mm min horizontal 0 43 3 in min 0 1100 mm min vertical Magnets deactivation Toggle switch Automatic stop Terminal contact switches at both ends 0 47 2 in min 0 1200 mm min horizontal Dimensions 0 43 3 in min 0 1100 mm min vertical Weight 17 6 1 5 8 kg Noise Level 70 dB Oscillation type Angular max 11 Amplitude R 6 150 mm 0 07 1 2 2 30 mm Oscillator Frequency 12 115 cycles min Delay at ends 0 3 s Max moment 1 1 Ft Ibs 5 Nm 17
13. a total travel distance above a value of 400 inches switches the machine to a mode of an infinite travel distance A stopping of the machine is only enabled by using the travel direction switch or activation of any terminal contact switch sd ARC Runner 11 2011 Operations Manual for Welding Carriage ARC Runner The infinite travel distance mode is displayed in such form Total length ipm Infinity 20 0 9 WORK Connect a welding generator to the arc ignition socket E 2 Toggle the arc ignition switch C to I No arc is initiated but the machine is ready To test the function of arc initiation to ensure that all connections are made use the Test position No travel will take place 3 Toggle the power switch to I A This will initiate the arc and after a slight delay will cause the carriage to begin travelling and if installed and programmed will cause the oscillator to begin its programmed movement 4 Toggle the travel direction switch to a desired direction B The welding carriage will begin to weld with programmed parameters To stop the carriage toggle the travel direction switch B 10 ADJUSTMENT AND MAINTENANCE Adjustment and maintenance activities should be carried out after unplugging the carriage from power Maintenance 1 Cleaning of wheels of sand and metal chips the lower plate guiders each time after finishing work 2 Lubricate threads in the guiders assembly e g Mobilux
14. ast design with a ergonomic access to operation components It is lightweight easy to carry and position on the workpiece The drive is provided with a 30W motor reducer in the drive unit 1 which drives 4 wheels 8 equipped with high thermal resistance properties It is powered by 115 230 V 50 60 Hz The magnetic block with permanent magnets activated by the toggle switch 9 enables adherance of the carriage to flat ferromagnetic surfaces at a maximum pitch of 90 The follower 3 in the driving assembly 1 enables a stable controlled direction travel during a welding process The guides assembly 2 enables a precise adjustment of a torch position in a horizontal or vertical axis The control panel 5 with the large display enables the input of various operational parameters for the carriage and the oscillator in a comfortable and precise way Different types of torch holders 6 may be mounted on the torch plate 4 or the oscillator 10 The welding carriage without oscillation 4 Torch plate 6 Torch holder 7 Hose holder 2 Guides assembly 1 Driving unit 3 Follower 5 Control panel 9 Toggle switch 8 Wheel ARC Runner 11 2011 Operations Manual for Welding Carriage 3 ARC RUNNER PROPERTIES 1 Forged and sealed housing which prevents corrosive welding substances from entering This compares to bent sheet metal units which are not sealed and fail often from ingestion of foreign elements Gear driven four wheel
15. be suspended to decrease towed weight For welding operations on surfaces in a vertical or upward angled position use a safety string that prevents uncontrolled movement as shown below SAFEGUARD CARRIAGE ARC Runner 11 2011 Operations Manual for Welding Carriage 14 It is not permitted to use to safety strings when welding operations are carried out on surfaces pitched sideways to a direction of travel SAFEGUARD CARRIAGE SAFEGUARD 15 Do not leave the machine unattended especially when it is travelling 16 Do not force the Carriage to stop by hand Always use the STOP setting 17 Do not take off the Drive Wheels Guard as this will cause damage to the wheels if the welding is close to the carriage 18 Do not stand or walk underneath the machine 19 Any assembly and disassembly of parts must be done when the carriage is disconnected from power 20 The carriage should be removed from working area and locked away in a secure place when not in use ARC Runner 11 2011 Operations Manual for Welding Carriage 6 PREPARATION FOR WORK 1 Take the welding carriage out of its packaging 2 Inspect the welding carriage for any shipping damage only original packaging guarantees appropriate protection 3 Inspect power supply cable if damaged replace it with a new original unit 4 Inspect the power socket clean it if needed do not use compressed air 5 Connect a power cable to the machine
16. ds the process of programming of the technological parameters of the carriage and oscillator It is a screen that allows saving of the settings under a chosen number of the set parameters The following information will appear on the display Save setup ipm Setup 1 20 0 A specific setup should be chosen by turning the function knob F2 in a range 1 to 40 and then the knob should be pushed Be careful not to overwrite and existing program that is still being used The system will confirm saved settings with the following information on the display Save setup Done ipm 20 0 ARC Runner 11 2011 Operations Manual for Welding Carriage INFORMATON In this mode an operator has following options Turning the function knob F2 again and depending on the rotation direction increases or decreases the number of parameters set Pushing the function knob F2 results in saving of the set parameters again e g under different number of the set parameters Turning of the function knob F1 depending on a direction results in a step to next or previous menu of the carriage Pushing and holding for approx 3 seconds results in an exit to the main menu of the carriage The machine is ready to work A turn of the function knob F1 again results in a step to a procedure of loading previously set technological parameters In this case a following information will appear on the display Load setup ipm Setup
17. er 11 2011 Operations Manual for Welding Carriage
18. mm Power supply 115 230V 50 60Hz separate units due to plug interface Welding position vertical horizontal Material thickness 3 16 5 mm minimum Base material clearance 3 16 5 mm Driving mechanism Four high temperature resistant silicone wheels with the magnetic block gear driven no belts to replace Guiding system Two roller guides in various configurations Towing force 33 7 Ft Ibs 150 vertical 49 5 Ft lbs 220 horizontal Torch Top Down 1 4 in 85 mm adjustment Left Right 1 4 in 35 mm Guider adjustment 3 0 in 75 mm program start direction left Travel direction switch stop program start direction right Function button F1 Continuous welding dash crater fill backweld The carriage controller Function button F2 Value change Arc ignition switch TEST 0 1 Speed knob 0 47 2 in min 0 1200 mm min horizontal 0 43 3 in min 0 1100 mm min vertical Automatic stop Terminal contact switches at both ends 15 x 14 6 W x 15 4 Dimensions 382 mm L x 372 mm W x 390 mm H Weight 17 6 lbs 8 kg Noise Level 70 dB ARC Runner 11 2011 Operations Manual for Welding Carriage Steeimax ARC Runner THE CARRIAGE CONTROL PANEL Power switch 1 0 Travel direction and program activation switch Program start left direction stop prog
19. only three options A change of a travel speed with a resolution 1 or 0 1 b A choice of work parameters of the carriage C Access to programming parameters of welding parameters of the carriage Turning of the control knobs F1 and F2 does not result in a change to another previously stored control program of the carriage It is a safety feature against accidental change of the welding parameters which were previously configured or input by an operator sas ARC Runner 11 2011 Operations Manual for Welding Carriage INFORMATION a In order to adjust the welding speed with the 0 1 resolution the SPEED knob has to be pressed and turned simultaneously in required direction A clockwise turn increases a the speed by 0 1 min where a turn in counter clockwise direction reduces it with by 0 1 min A turn of the SPEED knob without pressing causes a change of the welding speed with 1 min step The range of the speed adjustment is 0 to 40 ipm and is electronically limited To choose a set of working parameters Setup 1 to Setup 40 the F2 function knob has to be simultaneously pressed and turned in the required direction A turn in a clockwise direction causes a step to a next set of parameters where a turn in counter clockwise direction causes a step to a previous set of parameters After setting a required set of parameters the control system stores it automatically and further confirmation is not required
20. ram start right direction Arc ignition switch TEST 0 I Power socket Arc ignition socket Function knob F1 Function knob F2 Travel speed adjustment knob SPEED Oscillator connection socket Display cTIOTIMUN gt Runner 11 2011 Operations Manual for Welding Carriage 5 SAFETY All set up handling and repair operations of the Carriage may only be carried out by trained personnel Read the User s Manual and follow all the instructions before using the machine The machine is not waterproof Operations in damp conditions may be cause damage to the machine Check if the drive wheels are properly engaged on the workpiece Place all the wheels on a steel plate Contact between the lower face of the chassis and base material is not permitted Inspect rubber tires of the driving wheels for damage and metal chips Clean off any metal objects adhering to the lower face of the chassis Before starting operations ensure that the magnet block is switched on Carry and place the carriage only when the magnet block is switched off in the 0 position Carry the machine by holding its handle do not grip it by its lower plate it may cause injury to your fingers Always place the Carriage on clean surfaces sand or metal chips free Do not plug in to the power source unless the Power Switch is in 0 position Use appropriate power supply cables without cracks and isolated Torch hoses should
21. set with the function knob F2 A range of a change of the oscillation is specified in the paragraph 10 2 e Anext turn of the function knob F1 in a clockwise direction results in a step to a next menu which is related with a configuration of the oscillator parameters The following information will appear on the display Osc UP ipm 1 0s 20 0 The machine is in the mode of programming of a delay time oscillation stopping for an upper position of the oscillator arm A desired value in a range of 0 25 seconds should be set with the function knob F2 A value of 0 is corresponding with a lack of the time delay in the upper position of the oscillator arm and the oscillator immediately changes the direction of motion e Anextturn of the function knob F1 in a clockwise direction results in a step to a next menu which is related to a configuration of the oscillator parameters The following information will appear on the display Osc dly DN ipm 1 0s 20 0 The machine is in a mode of programming of a delay time oscillation stopping for the lower position of the oscillator arm A desired value in a range of 0 25 seconds should be set with the function knob F2 A value of 0 is corresponding with a lack of the time delay in the lower position of the oscillator arm and the oscillator immediately changes the direction of motion e Anextturn of the function knob F1 in a clockwise direction en
22. st of working parameters of the carriage depends on the machine configuration In case of work with the oscillator the main menu contains additional options specific for a welding with oscillation b The welding carriage automatically recognises the presence of the oscillator immediately when the machine is activated with the power switch A after oscillator was plugged into J socket beforehand A correct connection between the welding carriage and the oscillator is signalled with a message Oscillator found After a correct installation of the control system of the welding carriage not interrupted by alerts from the terminal contact switches or the travel direction switch the following message is displayed Ready ipm Setup 1 20 0 DESCRIPTION ipm unit of travelling speed inch per minute NOTE At the current level of a design development of the welding carriage all technological parameters referring to a length of a weld or dash are given in inches Ready the field shows current state of work of the carriage The machine is ready to begin operations Depending on the work mode different messages are displayed Setup 1 a setting of work parameters No 1 saved in the carriage s memory It is possible to save up to 40 independent sets of welding parameters input value of a travel speed During work this field displays a real welding speed In a Reagy state the control system allows
23. step to the main menu of the carriage The machine is ready to work 21 ARC Runner 11 2011 Operations Manual for Welding Carriage 12 5 The oscillator setting operation The oscillator is automatically detected by the carriage after connection Set technological parameters of the oscillator in the control panel see 10 4 The oscillator is ready to work Carry out a test of the technological parameters see paragraph 6 The carriage is ready for work Runner 11 2011 Operations Manual for Welding Carriage 22 V 13 ELECTRICAL SCHEMATIC DIAGRAM ACE Runner without oscillation m P1102 12 Supply cta 1 1 C ARC ENABLE TRAVEL SWITCH i400 CARRIAGE mo 470205000 1 T LIMIT FRONT LIMIT REAR IE F ii SUPPLY i i Li 1 amooo 47601 17 00 0 T 460118060 1 L 1 di bb kh 4760904000 466 17 0000 0 5 SWC14 P1104 V11 MainBoard TERE EE ddd de 476 02 02 020 Vm 476 01 06 040 0 P i I S ble o F 8 23 11 2011 Operations Manual for Welding Carriage ARC Runner 14 EC DECLARATION OF CONFORMITY Declaration of compatibility We PROMOTECH Ltd Elewatorska Street 23 1 15 620 Bialystok Poland declare with full responsibility that product ARC Runner Welding Carriage which the declaration applies to is in

ARC RUNNER WELDING CARRIAGE

Contents

Download Pdf Manuals

Related Search

Related Contents