User Manual For WT-244 - GSM Gateways Premicell Fixed Cellular
Contents
1. WT 244 GSM 4 Ports Analog Gateway User Manual WhTURA CORPORATION SDN BHD Analog Gateway GSM Gateway Introduction Welcome to use our GSM Analog Gateway also named as Analog Channel Bank SIM Bank to enter a novel communication world which absorbs high tech and delicate design out of your imagine The GSM Analog Gateway enables you to quickly achieve the GSM cell telephone communication just via simple operations of wired telephone This briefing helps you understand the functions of GSM Gateway step by step Before using that equipment please read this briefing in details OVERVIEW e 4 Voice channels are individually connected with 4 ports of GSM brand new industrial GSM modules e Simple Installation Easy Configuration via DTMF e LED GSM status display e GSM Frequency Bands 900 1800Mhz dual band 850 900 1800 1900Mhz quad band e Anti Polarity Signal Better reversal for accurate billing e High gain external antenna with 3m cable for optimal signal strength e Quick call set up and release echo cancellation e 4 SIM per channel e Individual Channel power supply for easy card replacement e Thunderstorm and lighting protection WT 244 APPEARANCE VIEW Front View with Power Switch amp Antenna WT 244 USER MANUAL Rev 1 Technical Support technical witura com COPYRIGHT 2008 WITURA CORPORATION SDN BHD 1alog Gateway Rear View View of 4 SIM Card Holder at the boar2. 1 means able to use Example 3 20 means SIM Card No 2 is disable 3 41 means SIM Card No 4 is enable Notes If the Setting for SIM Card No X cannot be used it will automatically skip the SIM Card No X when the SIM Card is routing Auto switching when the SIM Card is routing iii If only required using ONE SIM Card it should be setting to disable for the rest of the 3 SIM Card At the same time set this SIM Card to enable and start to use from this SIM Card iv If using TWO SIM Card is enable if the number of times using did not set every SIM Card only will use ONE time system will automatically go into the routing mode The default Number of times using every SIM Card is 1 Incoming Call Setting 4X Setting for Barring Incoming Call X Q means Barred Incoming Call X 1 means Allowed Incoming Call Example 40 means Barred Incoming Call 41 means Allowed Incoming Call WT 244 USER MANUAL Rev 1 Technical Support technical witura com COPYRIGHT 2008 WITURA CORPORATION SDN BHD alog Gateway 4 Speed Dial Setting e 5X Indicate the delay time seconds for speed dial X 1 8 Example 52 means auto dial number after 2 seconds dialing destination no 55 means auto dial number after 5 seconds dialing destination no 5 Setting for Factory Default 000 e Default Setting for SPK is 2 e Default Setting for MIC is 2 e Default Setting for SIM Card is using SIM Card No 1 e D
3. e Block unwanted prefixes e High gain external antenna with 3M cable for optional signal strength e Quick call set up and release e Echo cancellation e Accurate called connected reverse polarity signal for billing e CLID PIN audio set capability e Automatic end of dialing after 3 seconds no SEND key e Support Inbound and Outbound Caller ID display e Worldwide flexible power supply e Add prefixed code automatically e Locking wireless terminal e Locking SIM Card e Locking service provider e Locking districts e Call billing prefixed e Caller ID blocked optional and need network supported e Voice volume adjustable e Providing corporate business fixed to mobile mobile to fixed telephony e Providing rural connectivity over GSM networks e Providing quick basic telephony provisioning e Providing GSM connectivity for river boats coastal cruise ships e Providing connectivity to fixed network back up via GSM e Providing VPN connectivity between two corporate businesses with high security requirements and many other more applications WT 244 USER MANUAL Rev 1 Technical Support technical witura com COPYRIGHT 2008 WITURA CORPORATION SDN BHD alog Gateway DESCRIPTION FOR SETTING Entering the setting 2008 from a DTMF Phone in order to go into the Setting Mode When hang up the phone it will save and quit from the setting mode 1 Volume Setting X Adjust the SPK High or Low X indicate H
4. Fix the bottom cover and tighten the screws d Wiring antenna into antenna electric outlet e Connect one end of the line with the RJ 11 telephone outlet and the other end with the telephone fee counter f Connect one end of a 85 240V AC power adapter into 110 220V power outlet the other end into 220V power outlet on behind panel g Open the power switch on behind panel switch is placed in NWN 7 appearance After the equipments installed each route of the equipments has to be initially systematic configured by dealer or network service provider to assure the formal operation of equipments 3 Instruction a This PRI Gateway Analog Channel Bank application figure GSM PRI Gateway Analog Channel Bank Advance VOIP Billing amp INTERNET Firewall GSM Network Global PSTN Phone Phone Client from GSM WT 244 USER MANUAL Rev 1 Technical Support technical witura com COPYRIGHT 2008 WITURA CORPORATION SDN BHD orts Analog Gateway GSM Analog Channel Bank Phones The installation connecting to charging device GSM Analog Channel Bank b The front panel indicator appearance illumination There are pick up or hang up handset indicator and strong or weak signal indicator for each route of the PRI Gateway Analog Channel Bank Pick up or hang up the handset If pick up a route of the PRI Gateway Analog Channel Bank the pick up or hang up indicator keep bright Red LED Stro
5. MANUAL Rev 1 Technical Support technical witura com COPYRI GHT 2008 WITURA CORPORATI ON SDN BHD inalog Gateway 2 SIM Card It support 3VG SIM Card 3 Phone Interface Supply main and assist double frequency interface RJ 11 Phone Interface Hanging Voltage 45V Picking Off Voltage 30mA 41mA Dialing Tone Frequency 450Hz 4 Antenna interface Antenna Amplifying gt 4 5DB 5 Adapter Interface INPUT AC 175 260V OUTPUT 9V 1000MA 6 Operation Circumstance Operation Temperature 10 C 60 C Storage Temperature 20 C 70 C Operation Humidity 45 95 Atmosphere pressure 86 106Kpa Environment noise lt 60DB Transmitting Power 2W Sensitivity lt 104Dbm Antenna Amplifying gt 1 5db Dialing frequency 450Hz Hanging Voltage 45V Picking current 30mMA 41mA Power input 85 240V WT 244 USER MANUAL Rev 1 Technical Support technical witura com COPYRIGHT 2008 WITURA CORPORATION SDN BHD alog Gateway EXCEPTION HANDLES 1 Network After opening the GSM PRI Gateway Analog Channel Bank the equipment needs about 10 seconds to search for the local network of GSM When searching the most right hand signal strong or weak indicator would flash once per second until searching completes then the strong or weak signal indicator starts indicating to make a phone call 2 Power Connect to power supply and make sure you have opened the power switch
6. PORATION SDN BHD 1g Gateway alo ew f Replacing SIM Card If the SIM Card needs to be often replaced the user can replace the single channel SIM Card without influencing others Please press the RED key in front of the unit regarding the channel which will be replaced and make it power off separately The power LED will be turn off and then open the front upper cover and press the key of channel which needs to replace SIM Card the LED light aside the SIM Card will go off Then the SIM Card can be placing press the key again and the LED light aside the SIM Card will shine bright If other SIM Cards need to be changed it is the similar with above steps OTHER SPECIFICATIONS p Support Protocol GSM07 10 Maximum RF power output 2W GSM Dialing Tone 450Mhz continuum Busy Tone 450Hz 0 35S 0 35S Product Shell Steel RF Parameter KOdulation 0 3GMSK Channel Interval 200KHz Frequency difference lt 0 1ppm Antenna Gain Inside keeping 3db outside keeping 5db Antenna Resistance 500hm Standby current lt 15mA Average communicating current lt 300MmA Support 3 0V 1 8V SIM Card Adaptively SS eS as eS YE e O he e KL U N TECHNOLOGY I NDEX 1 Antenna interface level 900 1800Mhz or 850 900 1800 1900Mhz GSM 850Mhz RX 869 894 TX 824 849 GSM 900Mhz RX 925 960 TX 880 915 GSM 1800Mhz RX 1805 1880 TX 1710 1785 GSM 1900Mhz RX 1930 1960 TX 1850 1910 WT 244 USER
7. atch with the equipments The unqualified antenna in use will damage the equipments Antenna must keep vertical and off the telephone the antenna cable cannot be bound with telephone line together Do not touch antenna or approach antenna in range of 10m during calling Power The equipments regularly use 110 220V AC Installation and connection Make sure the Power Switch on the panel is placed in break the switch is placed in the O position when installing the equipments and connecting with other equipments according to the guidebook Operating with electricity may damage the equipments Configuration After the equipments installed only after each route of the equipments has been system initially configured by dealers or network service provider the equipments can perform formally Only dealer or network service provider can initially configure the equipments system avoiding the equipments damage due to the mistake of system configuration Connecting to other equipments While connecting to other equipments please read the user guide carefully to acquire detailed safety guide Do not connect to the products which do not match with the equipments WT 244 USER MANUAL Rev 1 Technical Support technical witura com COPYRIGHT 2008 WITURA CORPORATION SDN BHD nalog Gateway SUMMARY The design of the PRI Gateway Analog Channel Bank aims to provide a kind of Standard frequency telephone in the area cov
8. behind the GSM PRI Gateway Analog Channel Bank power switch is placed in appearance and the switch key on the each route inside the equipment While turning on the equipment all indicators on front panel will flash once a Check out the 100 200V AC power line connecting well with an alternate current electric outlet and with the AC outlet of the PRI Gateway Analog Channel Bank intact b If the above check can t expel the breakdown yet please contact the dealer 3 Speakerphone It the speakerphone can t work normally please check whether the operation is correct and the connecting with GSM Analog channel bank is well Otherwise try to change another telephone to test whether the condition and internal circuits of the equipment work normally or not Due to the strong shooting power of the equipment it is Suggested to use the telephone with anti electromagnetism interference to prevent headphone from interference voice WT 244 USER MANUAL Rev 1 Technical Support technical witura com COPYRIGHT 2008 WITURA CORPORATION SDN BHD jalog Gateway FEATURES BENEFITS p e Plug And Play Simple installation and easy configuration via DTMF e Takes only minutes to install and start service e Supports 900 1800 dual band or 850 900 1800 1900Mhz quad band e Signal auto sensing for port hanged prevention e Providing Low cost to setup voice directly into the GSM Network over VOIP FXO termination
9. d of 1 Port ATTENTION e Please read the following specific rules Against the rules will cause danger or violate the law e Echo off Before using this equipment please make sure your position has no echo off function for wireless radio frequency signal e Interference The similar to all mobile telephones it is subject to the interference which affects functions of the telephone e Explosion district At explosion districts or places signed close wireless transmitting devices please do not use the equipments e Latent explosion environment At environment that there is latent explode possibility such as gas station chemistry products combustible liquid air conveyance car or store warehouse etc please do not use the equipments WT 244 USER MANUAL Rev 1 Technical Support technical witura com COPYRIGHT 2008 WITURA CORPORATION SDN BHD Children Do not let the children play the equipment Children may be stabbed or hurt other people with the antenna Children may damage the interface or make telephone calls freely to increase your telephone expenditure Maintenance Only the qualified technicians can install or maintain the equipments If the equipment aborts please contact the dealer Do not open the equipments or maintain them by groups and individuals without authorization to prevent damaging the equipments Antenna Only approval antenna can be used do not link the antenna which do not m
10. e arising out of abuse and improper application of the equipment Note Wherever possible return only the PCB to Witura Service Centres DO NOT return the enclosure The WT 244 is a product of Witura Corporation Sdn Bhd and is manufactured by Shenzhen Witura Telecommunications Co Ltd WT 244 USER MANUAL Rev 1 Technical Support technical witura com COPYRIGHT 2008 WITURA CORPORATION SDN BHD
11. efault Setting for Incoming Call is Barred Incoming Call e Default Setting for Speed Dial is Delay Time for 3 Seconds Notes a The default Number of times using every SIM Card is 1 b The default for SIM Card No 2 SIM Card No 3 SIM Card No 4 is disable and only can use SIM Card No 1 The system will keep continuing using SIM Card No 1 c If need to use SIM Card No 2 it cannot directly do setting for starting using SIM Card No 2 It must be first setting to SIM Card No 2 as Able to use mode otherwise it will indicate Error DESCRIPTION FOR PANEL INDICATOR me 1 Display Indicator Signal Strength SIM Card No X currently in used Display Alternatively e L1 L5 Indicate the Signal Strength Example L1 as Weakest L5 as Strongest e 1 S4 Indicate the SIM Card No X is currently in used WT 244 USER MANUAL Rev 1 Technical Support technical witura com COPYRIGHT 2008 WITURA CORPORATION SDN BHD Example S2 means SIM Card No 2 is currently in used Error Indicator E1 Indicate there is connection problem between the Modules and the PCB Board If the display show El more than 5 seconds after the terminal switch on E2 Indicate Cannot Read SIM Card E2 and SIM X will take turn to display E3 Indicate Can Read SIM Card but No Signal E3 and SIM X will take turn to display 2 LED Light Indicator 1 LED for WORK 1 LED for IN USE WORK The LED will lighten up when switch on t
12. ered by the digital mobile network The interface of the PRI Gateway Analog Channel Bank provides a transparent connection between the standard telephone and the mobile net which has the function of emulation exchange and offers the following function e Dialing tone e Dialing a number with DTMF e The bell flow signal e Versa pole signal The exterior interface of the PRI Gateway Analog Channel Bank has e RJ 11 electric outlets connecting to telephone or fee counter e Antenna electric outlets FME e Pick up or hang up the telephone handset indicator e The strong or weak signal indicator Configuration And I nstallation 1 The whole pack of the PRI Gateway includes e Analog Channel Bank Main Unit 1 set e High Gain Antenna 1 pcs e Antenna Splitter 1 pcs e 110 220V AC Power Line 1 pcs e Telephone Cord 4 pcs 2 Installation Procedure The equipment provides digital GSM network communication which required a valid SIM Card a Put he GSM Analog Channel Bank in pedestal b Switch of the power on the behind panel switch is kept at O c Insert the valid SIM Card WT 244 USER MANUAL Rev 1 Technical Support technical witura com COPYRIGHT 2008 WITURA CORPORATION SDN BHD e Screw off the two fixed screws in the bottom frontOpanel and remove the bottom front panel e Insert the SIM Card in the correct direction the most right hand route is from left to the right others are from right to left e
13. he terminal The LED will blink when the terminal finish register to the Network IN USE When the terminal is switch on the LED will lighten up When the terminal is switch off the LED will switch off One Reset button Can press Reset button when the terminal facing problem Notes After the setting please press Reset button then only start using If the setting is wrong there is a du du sound lii If the setting is successful there is a du sound iv When the call is successful start calculating charges then only consider as using the SIM for 1 time If the terminal indicates Error wait until the Light Indicator for WORK blink then the terminal will go into Setting mode It cannot call out If the user try to call out it will indicate du du sound WT 244 USER MANUAL Rev 1 Technical Support technical witura com COPYRIGHT 2008 WITURA CORPORATION SDN BHD Warranty Witura Corporation Sdn Bhd guarantees all WT 244 GSM 4 Ports Analog Gateway against defective parts and workmanship Witura Corporation Sdn Bhd shall at its option repair or replace the defective equipment upon the return of such equipment to any Witura branch This warranty applies ONLY to defects in components and workman ship and NOT to damage due to causes beyond the control of Witura such as incorrect voltage lightning damage mechanical shock water damage fire damage or damag
14. igh or Low X 1 5 1 is the Lowest SPK 5 is the Highest SPK Example 2 means SPK Volume as 2 4 means SPK Volume as 4 X Adjust the MIC High or Low X indicate High or Low X 1 4 1 is the Lowest MIC 4 is the Highest MIC Example 2 means MIC Volume as 2 4 means MIC Volume as 4 2 SIM Card Setting a b 1X Indicate starting to use from SIM Card No X X 1 4 Example 12 means starting to use from SIM Card No 2 14 means starting to use from SIM Card No 4 2 1XXX Indicate Number of times using SIM Card No 1 XX 001 999 2 2XXX Indicate Number of times using SIM Card No 2 XX 001 999 2 3XXX Indicate Number of times using SIM Card No 3 XX 001 999 2 AXXX Indicate Number of times using SIM Card No 4 XX 001 999 WT 244 USER MANUAL Rev 1 Technical Support technical witura com COPYRIGHT 2008 WITURA CORPORATION SDN BHD C Example 2 1008 means the number of times using SIM Card No 1 is 8 times 2 3125 means the number of times using SIM Card No 3 is 125 times 3 1X Indicate whether SIM Card No 1 enable or disable X 0 means disable to us X 1 means able to use 3 2X Indicate whether SIM Card No 2 enable or disable X 0 means disable to us X 1 means able to use 3 3X Indicate whether SIM Card No 3 enable or disable X 0 means disable to us X 1 means able to use 3 4X Indicate whether SIM Card No 4 enable or disable X 0 means disable to us X
15. ng or weak signal Indicating the received signal of each route GSM Analog Channel Bank The stronger the signal is the more the bright lights will show In the state of system configuration four lights flash Green LED WT 244 USER MANUAL Rev 1 Technical Support technical witura com COPYRIGHT 2008 WITURA CORPORATION SDN BHD c Make a call MSN Phone Il Phone 2 Base Station Phone 3 Phone 4 Terminal box Phonen GSM Terminal When the strong or weak signal indicator indicates there is enough receiving Signal pick up the telephone which connecting with the PRI Gateway Analog Channel Bank and you can hear the dialing tone immediately If connecting the machine with the fee counter it will show the telephone number you dial After the other side picks up the phone handset the charging machine starts working For shortening the network accessing time it is suggested to press the key after dialing the telephone number means to press the accelerates dial key Without dialing more numbers in 7 seconds after first dial the first telephone number will be redialed automatically d Callin When there is a call in the telephone rings Pick up the phone and converse e The operation method of the charge machine Please read the charge machine manual about the detailed operation method WT 244 USER MANUAL Rev 1 Technical Support technical witura com COPYRIGHT 2008 WITURA COR
Download Pdf Manuals
Related Search