User Manual for Wicker Patio Heater model 60763
Contents
1. 17 TROUBLESHOOTING Problem Problem cause solution Burner will not light Pilot light assembly bent Place pilot in proper position or not in correct location and retry Supply hose is bent or twisted Blockage in burner Clean or replace injector injector Burner flame goes Low gas pressure Let the pilot flame stay lit for off immediately 10 minutes before setting nition variable knob to LO Blockage in burner Clean or replace burner injector injector surface cylinder Blockage in burner Turn off the heater and let it cool Remove blockage and clear burner inside and outside Clean reflector screen Straighten hose and perform leak test on hose Burner flame is low burner Emitter unevenly glows Thick black smoke Dirt or film on reflector and flame and flame screen Carbon build up Manufacturer Changzhou Wellife Furnace Co Ltd Add Xingiao Village Zouqu Town Wujin Distrct Changzhou City Jiangsu Province China Tel 86 519 83310111 Fax 86 519 83311577 www globalwellife com 18 Distributed By Well Traveled Living 716 S 8 Street Amelia Island FL 32034 Toll Free 866 WTL SUPP 1 YEAR LIMITED WARRANTY Customers in the Continental US All components are warranted for a period of 1 year after date of purchase by the original owner against defects in material2. re Be yE af 2tLow d ae oo O O amp Incorrect flame HIGH Correct flame LOW Visually check the hose assembly inside the post and check for any cracks or worn sections 1 Unscrew gas hose and regulator hose with 3 4 inch open end wrench and adjustable wrench Screw down the screws on pole and take out the burner head assembly Check if there are any cracks or worn sections on hose If yes contact your gas supplier to replace the hose 4 At least once a year the unit should be inspected for the presence of spiders spider webs or other insects Air flow must be unobstructed Keep controls burner and circulating air passageways clean Signs of possible blockage include 1 Gas odor with extreme yellow tipping of flame 2 Heater does not reach the desired temperature 3 Heater glow is excessively uneven 4 Heater makes uneven popping noise Spiders and insects can nest in burner or orifices This dangerous condition can damage heater and render it unsafe for use Clean burner holes by using a heavy duty pipe cleaner Compressed air may help clear away smaller particles Carbon deposits may create a fire hazard Clean dome and engine with warm soapy water if any carbon deposits develop NOTE In a Salt air environment such as near an ocean corrosion occurs more quickly than normal If the heater is exposed to this type of environment you should frequently check for corroded areas and repair them promptly
3. base 12 Post support 13 6pcs M6x1i2mm bolts for connection of LPG cylinder fixed parts with base 14 3 pcs Support legs 15 Base 16 1 pcs open end wrench 10 amp 13mm 17 Wheel assembly PRECAUTIONS ATTACHING WHEEL ASSEMBLY Step 1 1 1 Locate Wheel Assembly 17 and 2 nuts bolts contained in plastic bag with Wheel Assembly Fig 1 Fig 1 ae A pea Step 2 2 1 Turn Base 15 so that holes for attachment of Wheel Assembly are facing you Fig 2 2 2 Align holes in Wheel Assembly 17 with holes on Base 15 Fig 3 Insert bolts through both sets of holes and secure nuts on end of bolt Fig 4 Fig 3 Fig 4 Step 3 3 1 Wheel Assembly 17 should now be attached to Base 15 as shown Fig 5 idee Fig 5 ASSEMBLY WARNING This appliance requires installation by a competent person Proper assembly is the responsibility of the installer Step 1 1 1 Attach 3pcs LPG cylinder fixed parts on the base with 6pcs M6x12mm bolts 1 2 Position the 3 pcs support legs on the base as shown in the picture to the right 1 3 Use 3 pcs M8x16mm bolts to affix the support legs to the base Step 2 2 1 Put the post support on top of the 3 pcs support legs 2 2 Use 6 pcs M6x30mm bolts and 6mm nuts to connect the post support and support legs 2 3 Use 4 pcs M6X10mm bolts to connect the first piece of the post assembly to the post support ASSEMBLY Step 3 3
4. 1 Connect the second piece of the post assembly to the first piece of the post assembly and screw on clockwise Step 4 4 1 Place the tank cover on the base Step 5 5 1 Secure the 3 pcs 90mm pins reflector support bolts on the cap of emitter screen Route the gas hose up through the post and out of the top Connect the gas hose to the gas burner inlet connector Use 2 wrenches to screw the gas hose and connector to gether tightly Fix the head unit collar to the post with 4 pcs M6x10mm bolts PRECAUTIONS Reflector 2 is comprised of 3 outer pieces and 1 center piece Locate all 4 pieces of Reflector 2 which are wrapped in bubble wrap Unwrap and remove all pieces and peel off the protective blue plastic on each piece Locate 9 bolts and 9 cap nuts in the plastic bag Align the 3 outer pieces with the 1 center piece and place a bolt through the center hole on each piece as shown below Tighten castle nut on each bolt Next align the sides of each outer piece and the center piece and insert the next 3 bolts through both holes Tighten castle nuts on bolts Finally insert bolt through holes located at outside edge of adjoining panels of the reflector side pieces 3 bolts required and tighten castle nuts on bolts ASSEMBLY step 6 6 1 Put 8mm washer on each reflector support bolt 6 2 Fasten the reflector with 3 pcs washers and 3 pcs M8 mm castle nuts step 7
5. 7 1 Lift the tank cover and rest it on the post flange 7 2 Connect the other end of gas hose with regulator to the gas cylinder and tighten Warning When connecting the gas cylinder and regulator make sure the connection is tight and always check for any leaks Please see page 9 Check for Leak for full instructions 7 3 Put gas cylinder on the stand ee ASSEMBLY 7 4 Lower tank over gas cylinder and down to cover base Check for Leak Your patio heater has been checked at all factory connections for leaks but you should always check when you attach the LPG cylinder To check for leaks follow these instructions Assemble all gas connections Connect regulator assembly to the propane tank Make sure the heater valve is turned OFF 1 Make soapy solution by mixing 1 part liquid dish soap and 3 parts water 2 Open the propane tank valve 3 Spoon several drops or use squirt bottle of the soapy solution onto the gas hose regulator and regulator cylinder connection 4 Inspect the connections and look for bubbles 5 If no bubbles appear the connection is safe 6 If bubble appears there is leakage Close the propane tank valve and loosen and re tighten this connection 7 Check for leakage again ee ASSEMBLY 8 If bubbles still appear close the propane tank valve and contact your gas supplier If a leak is detected DO NOT attempt to use the heater A N i A 4
6. HILE IN USE CAUTION WHEN CERTAIN MATERIALS OR ITEMS ARE LEFT UNDER THIS HEATER WHILE IN USE THEY WILL BE SUBJECT TO RADIANT HEAT AND COULD BE SERIOUSLY DAMAGED This heater is to be used for the heating of outdoor patios decks spas pool and open working areas This heater is for outdoor use ONLY Always make sure that adequate fresh air ventilation is provided and follow the spacing tolerances shown in the picture below The minimum clearances must be maintained at all times This heater must be placed on level firm ground Never operate in an explosive atmosphere Keep away from areas where gasoline or other flammable liquids or vapors are stored or used Ge MAINTENANCE CLEANING AND MAINTENANCE WARNING To enjoy years of outstanding performance from your FOR YOUR SAFETY heater make sure you perform the following maintenance DO NOT touch or move on a regular basis heater for at least 45 minutes after use Allow all burner elements 1 Use warm soapy water for cleaning Never use flammable to cool before touching or corrosive cleaning agents 2 While washing your heater be sure to keep the area around the burner and pilot assembly dry at all times If the gas control is exposed to water in any way DO NOT try to use it It must be replaced Keep exterior surfaces clean Keep the heater area free and clean from combustible materials gasoline or other flammable vapors and liquids Visually check burner flames
7. OTICE Do NOT return to place of purchase For customer service and warranty issues contact our Customer Service Center at 866 985 7877 OR Email cservice welltraveled net Customer Service Hours Mon Fri 9 00 a m 6 00 p m EST Fire Sense and Well Traveled Living are registered trademarks of Well Traveled Imports Inc All assembly instruction presentations are the property of Well Traveled Imports Inc and are protected by U S copyrights and trademarks All rights reserved
8. OVE PURCHASER ASSUMES ALL RISKS IN THE ASSEMBLY AND OPERATION OF THIS UNIT FAILURE TO FOLLOW WARNINGS AND OPERATIONAL INSTRUCTIONS CONTAINED IN THIS MANUAL CAN RESULT IN SEVERE PROPERTY DAMAGE AND OR PERSONAL INJURY IN NO EVENT WILL WELL TRAVELED LIVING OR ITS DIRECTORS OFFICERS OR AGENTS BE LIABLE TO THE PURCHASER OR ANY THIRD PARTY WHETHER IN CONTRACT IN TORT OR ON ANY OTHER BASIS FOR ANY INDIRECT SPECIAL PUNITIVE EXEMPLARY CONSEQUENTIAL OR INCIDENTAL LOSS COST OR DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE SALE MAINTENANCE USE OR INABILITY TO USE THE PRODUCT EVEN IF WELL TRAVELED LIVING OR ITS DIRECTORS OFFICERS OR AGENTS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES COSTS OR DAMAGES OR IF SUCH LOSSES COSTS OR DAMAGES ARE FORESEEABLE IN NO EVENT WILL WELL TRAVELED LIVING OR ITS OFFICERS DIRECTORS OR AGENTS BE LIABLE FOR ANY DIRECT LOSSES COSTS OR DAMAGES THAT EXCEED THE PURCHASE PRICE OF THE PRODUCT SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO THE PURCHASER This limited warranty gives you specific legal rights and you may also have other rights which vary from jurisdiction to jurisdiction The provisions of the United Nations Convention on Contracts for the Sales of Goods shall not apply to this limited warranty or the sale of products covered by this limited warranty IMPORTANT N
9. Patio Heater Model PHO1 S PHO1 SS Item number 60763 WARNING For outdoor use only FOR YOUR SAFETY If you smell gas 1 Shut off gas to the appliance 2 Extinguish any open flame 3 If odor continues immediately call gas supplier FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance PLEASE retain this manual for future reference WTERTEK CERTIFICATE TO ANSI 83 26a 2008 cw CONFORM TO CSA 2 37a 2008 C US LISTED 3177588 Intertek Instruction Manual amp Parts List INSTALLER Please leave this manual to the consumer CONSUMER Please retain with this manual for future reference Manufacturer Changzhou Wellife Furnace Co Ltd Tools and parts needed for assembly DANGER CARBON MONOXIDE HAZARD This appliance can produce carbon monoxide which has no odor Using it in an enclosed space can kill you Never use this appliance in an enclosed space such as a camper tent car or home WARNING Improper installation adjustment alteration service or maintenance can cause injury or property damage Read the operating and installation maintenance instructions thoroughly before installing or servicing this equipment WARNING For Outdoor Use Only LPG cylinders to be used must be constructed and marked in according with US DOT specifications Storage of the heater indoors is permissible only if the LPG cylinder
10. e heater without the top canopy reflector or radiant screen Do not shorten the burner post assembly Do not use the heater in basements or below ground level It must always be placed on a solid and level surface Always ensure there is ample fresh air ventilation This heater is for outdoor use ONLY Never replace or substitute the regulator with any regulator other than the factory suggested replacement Do not clean the heater with cleaners that are combustible or corrosive Do not paint radiant screen control panel or top canopy reflector All leak tests should be done with a soapy solution NEVER USE AN OPEN FLAME TO CHECK FOR LEAKS The LPG cylinder should be turned off when the heater is not in use At least once a year the unit should be inspected for the presence of spiders spider webs or other insects PRECAUTIONS CHECK THE HEATER IMMEDIATELY IF ANY OF THE FOLLOWING EXIST 1 The smell of gas in conjunction with extreme yellow colored tips of the burner flames 2 The heater does not reach temperature 3 The burner makes a popping noise during use a slight popping noise is normal when the burner is extinguished after using Children and adults should be aware of the hazards of high surface temperature and should stay away to avoid burns or clothing ignition Young children should be carefully supervised when they are in the area of the heater Clothing or other flammable material should not be hung fr
11. ian K i j 3 j MAKE SURE to check all THREE connections between the cylinder and gas line NOTE 1 The cylinder must be provided with a shut off valve terminating in a LPG supply cylinder valve outlet specified as applicable for connection NO 510 in the standard for compressed gas cylinder valve outlet and inlet connections ANSI CGA v 1 2 The cylinder supply system must be arranged for vapor withdrawal 3 The cylinder used must include a collar to protect the cylinder valve Annually check operation A Lift the tank housing up above the LPG cylinder and rest it on the support leg assembly B Open the propane tank valve 12 ASSEMBLY C Spoon several drops or use squirt bottle of the solution onto gas hose connection and pilot connection D Inspect the connections and look for bubbles E If no bubbles appear the connection is safe F If bubbles appear there is a leak Close the propane tank valve and loosen and re tighten this connection G Check for leaks again H If bubbles still appear close the propane tank valve and call the gas supplier DO NOT attempt to use the heater OPERATION WARNING DO NOT attempt to operate heater until you have read and understand all precautions Failure to do so can result in serious personal injury death or property damage Before Turning Gas Supply ON Your heater was designed and approved for OUTDOOR USE ONLY _DO NOT use it inside a bu
12. ilding or any other enclosed area Make sure surrounding areas are free of combustible materials such as gasoline and other flammable vapors or liquids Ensure that there is no obstruction to air ventilation Be sure all gas connections are tight and there are no leaks Be sure the access panel is clear of debris Be sure any component removed during assembly or servicing is replaced and fastened prior to starting Before Lighting Heater should be thoroughly inspected before each use Have a qualified service person inspect the heater at least annually If relighting a hot heater always wait at least 5 minutes oes he ae OPERATION LIGHTING INSTRUCTIONS TO TURN ON THE HEATER 1 Turn the control knob OFF 2 Open gas valve fully 3 Press and turn the contro knob to HI position counterclockwise 90 Press down the control knob and hold 3 5 seconds While holding down the control knob press the igniter button several times until the pilot flame ignites Hold the knob about 30 seconds and then release control knob IGNITER Note If the pilot flame does not light or it goes out repeat Step 3 above NOTE If a new tank has just been connected please WARNING allow at least one minute or more for the air FOR YOUR SAFETY in the gas pipeline to purge out through the If at any time you are pilot hole or simply do Step 3 unable to light burner and When lighting the pilot flame make sure
13. is turned off and removed NOTE Use only 20Ib LPG tank with size of 18 1in 46cm Height x 12 5in 32cm Width Do not use if the environment temperature is below 40 degrees F 4 4 degrees C Tools needed e Open end wrench 10 amp 13mm included NOT included e Adjustable opening wrench 8 loang e Slip joint 9 long e Philips screwdriver with medium blade e Spray bottle of soap solution for leak testing PRECAUTIONS NOTE PLEASE READ THE FOLLOWING SAFETY RULES WARNING This heater must only be used outdoors Using this product in an enclosed area may cause injury death or property damage Only use in a well ventilated space Do not use in a building garage or any other enclosed area Read the instructions before use This heater must be installed in accordance with local codes or in the absence of local codes with the National Fuel Code ANSI Z223 1 If applicable the heater when installed must be electrically grounded in accordance with local codes or in the absence of local codes with The National Electrical Code ANSI NFPA70O Do not use the heater in an explosive atmosphere Keep the heater away from areas where gasoline or other flammable liquids or vapors are stored Prior to use check for damaged parts such as hoses regulators pilot or burner Turn off and disconnect the LPG cylinder before moving the heater Do not attempt to alter this heater in any manner EXAMPLE Using th
14. ning White smoke may appear around the radiant head during the first minutes of the initial firing When heater is ON Emitter screen will become bright red due to intense heat The color is more visible at night Burner will display tongues of blue flame These flames should not be yellow or produce thick black smoke indicating an obstruction of airflow through the burners If the flame is very small this indicates the supply pressure is not enough Relighting the heater 1 Turn the control knob to OFF position 2 Wait five 5 minutes before attempting to relight pilot 3 Repeat steps beginning with step 2 on page 12 Before leaving the heater unattended 1 Turn the control knob to OFF position and turn LP cylinder to OFF position 2 Never leave the patio heater unattended while in use Shut down instructions 1 Push in and turn control knob clockwise to OFF position 2 Turn LP tank gas valve clockwise to OFF position when heater is not in use NOTE After use some discoloration of the emitter screen is normal If you suspect gas leakage 1 Turn the control knob to OFF position 2 Turn LP cylinder to OFF position 3 Wait 5 minutes to allow gas to dissipate 4 If odor continues immediately call your gas supplier Warning Heater will be hot after use Handle with extreme care 15 control knob IGNITER control knob IGNITER LOCATION OF HEATER W
15. om the heater or placed on or near the heater Any guard or other protective device removed for servicing the heater must be replaced prior to operating the heater Installation and repair should be done by a qualified service person The heater should be inspected before use and cleaning may be required at least once a year or as necessary It is imperative that the control compartment burner and circulating passageways of the heater are kept clean Keep the heater area clear of combustible materials such as gasoline and other flammable vapors and liquids Do not obstruct the flow of combustion and ventilation air Keep the ventilation opening of the LPG cylinder enclosure free and clear of debris Storage of the heater indoors is permissible only if the LPG cylinder is turned off disconnected and removed from the heater Cylinders must be stored outdoors in a well ventilated area out of the reach of children Disconnected cylinders must have threaded valve plugs tightly installed and must not be stored in a building garage or any other enclosed area ASSEMBLY 3 pcs castle nuts Reflector 6 pcs 8mm washers for pins support 3 pcs 90mm L pins for reflector support Head assembly 4 pcs M6x10mm bolts 2 pcs Post assembly Tank housing Regulator 0 6 pcs M6x30mm bolts and 6mm nuts for connection of post support and support legs 11 3 pcs M8x16mm bolts for connection of support legs and
16. s and workmanship under normal use This warranty does NOT cover normal wear and weathering assembly and or maintenance OR use in a commercial application At Well Traveled Living s sole discretion products under warranty will be repaired and or replaced at no charge to the customer Any returns sent back to Well Traveled Living must be sent via prepaid freight and in the original retail packaging Web www wtliving com Email cservice welitraveled net For warranty service contact Well Traveled Living at the address phone numbers or internet site and email listed in this owners manual Be sure to have your sales receipt date of purchase and catalogue model numbers available when calling All warranty service will be coordinated by the Well Traveled Living s Amelia Island Florida service center This warranty is extended only to the original purchaser Proof of purchase will be required before warranty service is rendered The sales receipt is the only valid proof of purchase This warranty only covers failures due to defects in materials or workmanship which occur during normal use Failures and or damage which result from accident negligence misuse abuse neglect mishandling alteration or modification failure to maintain improper assembly or maintenance service by unauthorized agency or use of unauthorized components or damage that is attributable to acts of God are NOT covered THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED AB
17. that smell gas wait 5 minutes the variable control knob is continuously to allow gas to dissipate depressed while pressing the igniter button before attempting to light Variable control knob can be released after heater If after 1 minute the pilot flame has been lit for 20 20 you are unable to light seconds burner wait 5 minutes Pilot flame can be watched and checked from and allow flammable the peephole located on the base of burner Vapors to dissipate before If the pilot flame does not light or it goes attempting to light heater out repeat Step 3 again If the burner flame goes out accidentally or it is blown out by wind turn off the heater and wait at least 5 minutes or more to let the gas dissipate before relighting to avoid possible gas explosion Repeat steps 2 to 4 TO TURN OFF THE HEATER 1 Press and turn the control knob to OFF position 2 Turn off the valve on the gas cylinder and disconnect the cylinder IGNITER j OPERATION CAUTION Avoid inhaling fumes emitted from the heater s first use Smoke and odor from the burning of oils used in manufacturing will appear Both smoke and odor will dissipate after approximately 30 minutes The heater should not produce thick black smoke Note The burner may be noisy when initially turned on To eliminate excessive noise from the burner turn the control knob to the LO position then turn the knob to the level of heat desired War
Download Pdf Manuals
Related Search