Manual - Maytronics
Contents
1. MIMI communications cable Cable roller Floating cable Floating cable handle Impeller cover Roller inner connection Cable roller Connection cable between handle power supply and cable roller AC cable holder Power supply Main power supply Cable Figure 1 The Dolphin Wave Wave XL User Instructions 5 MMI GENERAL NOTES e n this user manual the instruction press Start is performed by pressing both green buttons 8 simultaneously on the MMI console Figure 2 The MMI is equipped with a screensaver that comes into effect after 5 minutes idle time Press Pool and Home in that order to unlock the MMI console Some options in the MMI menus are blocked by code in order to prevent un necessary changes of settings The code is the following key sequence OJOJOJO 3 2 1 6 DEFAULT SETTING FOR CLEANING SESSIONS This section explains how to proceed to the default setting for a cleaning session The robot is preset in the factory with certain configurations that enable you to commence pool cleaning immediately The settings made during this setup session remain in use until changed by the operator To start a pool cleaning session directly after you have assembled your Dolphin Wave proceed as follows 1 Lift the MMI s protective cover 2 Connect the robot s power supply to the main power supply line 3 Switch on the power supply The MMI s W2. Figure 13 Scanning mode 9 Set Scan Mode and choose either CrissCross Lines to scan or Pool with Obstacles ES CrissCross Scanning CrissCross Recommended Lines to Left Lines to Scan To be used when the pool scan needs to be limited to one direction or split into 2 sections Lines to Right Pool with Obstacles To be used in pools with an obstacle such as Island 10 After choosing the Scanning Mode you may choose the robot s progress direction Lines to Left or Lines to Right Figure 14 Scanning Direction screen Wave XL User Instructions 11 11 After setting the Scan Mode from the Pool Profile screen scroll down to the Pool A Profile next screen Figure 15 Delay Time Oh 12 Press Select to enter Delay Time Setting a Delay Time allows you to delay the start of cleaning operations by a time Reset Pool A profile factor selected from the MMI screen Line Spacing Medium 13 Line Spacing this parameter is used in order to optimize scanning Select Choose Fine Medium Coarse to set the distance between the lines 14 Reset Pool Profile Allows you to delete all igure 185 heels menur current pool profile parameters Pool Length Cycle Time Scan Mode Delay time During parameter setting operations Press Back to return to the previous screen Press HOME on the console to return to the Wave screen Starting Cleaning
3. On the spot turns On the spot turns can be carried out while the robot is in motion or executed when the robot is stationary 4 To turn the robot clockwise press and hold down the right arrow The robot will turn on the spot Release the button to stop the robot from turning 5 To turn the robot counter clockwise press and hold down the left arrow Release the button to stop the robot from turning 6 To deactivate the remote control unit press and hold down the touch pad The activation lights will switch off The robot reverts to its programmed direction mode of cleaning after the manual correction indicator lights switch off 41 The remote control unit deactivates automatically after approximately 3 minutes and the Maintaining the remote control unit The remote control unit is powered by 2 AAA batteries It is splash proof and should not be immersed in water To replace the batteries remove the 4 back cover securing screws and replace all the batteries with new battery cells Wave XL User Instructions 12 TROUBLESHOOTING How to save a log file to USB memory stick in case required by technician From the main Wave screen press on the green buttons in sequence right left right left and follow the further instructions Imp over load Imp over load Imp under load Drive over load Drive over load Drive under load DC input Robot is stuck on wall Out of water Robot is stuck
4. This is the default setting Maintenance 2 Clean the filter bag as needed When the MMI displays Filter Bag Full you should clean the bag before the next operating cycle Click the filter bag into its place e t is not necessary to stop the Dolphin Wave in the middle of the cycle when the Filter Full indicator appears Clean the filter before the next cycle e Filter bags can be cleaned in a washing machine hai o Before each operating cycle clean the robot s body brushes and driving belt area and remove foreign objects rubber bands hair etc Once a week clean the impeller area Remove the impeller cover s securing screw using a No 2 Philips manual screwdriver Twist counter clockwise and open the cylinder cover Remove foreign objects from the impeller Close the impeller s cover and replace the securing screw Keep the floating cable orderly enabling it to be rolled up easily Important Every 2 or 3 cleaning sessions disconnect the floating cable from the roller inner connection unroll the entire cable and re arrange it on the roller as required Preventive Maintenance PM should be performed on the Dolphin Wave robot in order to keep it in good and long lasting working condition Maytronics provides the parts required as a dedicated PM kit The work and the service will be provided through the dealer PM service should be performed every 1 500 wo
5. Navigation System Is there dirt or other foreign matter in the impeller Does the problem reoccur every operation Does the problem reoccur every operation Is there any interfering dirt in the driving belts brushes or drive axles Does the problem reoccur on every operation Does the problem reoccur on every operation Is there an electrical short partial or complete disconnection Is there a visible rupture in the floating cable Has the robot stopped in a vertical position of more than 70 Has the robot stuck on an obstacle Was the robot operated out of the water for an extended time Has the robot stopped on an obstacle Is there an obstruction in the water channel or in the robot s driving belts Does the problem reoccur every operation Wave XL User Instructions Unscrew the bolt that secures the protective cover of the impeller Turn it counter clockwise slightly until it is released Remove any dirt from around the impeller Replace the protective cover Contact Maytronics dealer Contact Maytronics dealer Remove any dirt or foreign bodies that might have become entangled with the driving belts brushes or drive axles Contact Maytronics dealer Contact Maytronics dealer Contact Maytronics dealer Move the robot from its position and remove the obstacle Reactivate If this reoccurs contact Maytronics dealer Check that the impeller is in order and that its
6. blades are not broken Reactivate If this re occurs contact Maytronics dealer Move the robot from its position and remove the obstacle Reactivate If this reoccurs contact Maytronics dealer Contact Maytronics dealer 15 Fuse Fail Wet connector Dry the connector and replace the fuse Note The fuse holder is located beneath the power supply on the right hand side Replace the fuse with the spare provided Note This is a special fuse and a replacement can be obtained from your Maytronics dealer No Does the problem occur when Contact Maytronics dealer Communication pressing POOL or HOME on Note You can work temporarily without using the MMI the MMI Disconnect it from the power supply thus disabling the Pool Home function and using the remote control Wave XL User Instructions WAVE 300 XL by Ma tre SNIC www maytronics com y y Re Exceptional y Experience
7. Operations Once all the customized settings have been configured you can proceed to a cleaning session 1 Prepare the Dolphin Wave for operation and immersion into the pool 2 On the MMI press POOL The robot starts moving towards the pool enters the pool and positioning itself on the pool floor 3 Wait for the WAVE screen to appear 4 In every activation of the robot it will straighten itself vertically to the wall of the starting point the robot will start moving backwards to straighten itself and then will continue in straight lines 5 Press Start The robot will start its cleaning operation If a Delay Time has been set see Configuring the Dolphin Wave above the countdown commences and the time remaining before automatic cleaning starts is displayed on the screen If no delay time is specified the robot begins cleaning immediately Once cleaning operations have started the MMI screen displays the countdown time as in Figure 4 To override the delay time to start cleaning immediately choose start from the delay countdown screen The robot will begin working immediately o If the screensaver is displayed press POOL and then HOME to unlock the MMI Wave XL User Instructions 10 OPERATING GUIDELINES A large sized swimming pool of approximately 300m requires approximately 3 4 hours to clean This is the default setting An Olympic size pool of 1 250m requires approximately 6 hours cleaning time
8. and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Changes or modifications to this equipment not expressly approved by the party responsible for compliance Maytronics Ltd could void the user s authority to operate the equipment 3 INTRODUCTION This user guide describes how to use your MMI operating console for the Dolphin Wave robotic pool cleaner The interactive state of the art MMI Maytronics Machine Interactive control console enables full control of the robot and allows you to determine the cycle time operation delay and cleaning scan that the robot performs It also enables diagnosis of various technical functions and parameters The console houses a remote control unit for manual operation and temporarily overriding automatic cleaning operations The Dolphin W
9. the receptacle is protected by a GFCI gt bs bs bs To reduce the risk of electric shock do not use extension cord to connect unit to electric supply provide a properly located outlet Please ensure that the following precautions are implemented Do not bury cord locate cord to minimize abuse from lawn mowers hedge trimmers and other equipment Only a trained operator should operate the Dolphin Wave Robot Pool Cleaner Operator should keep hands away from driving belt mechanism Position the Caddy and power supply at least 3 m 9 6 ft from the pool edge during operation Keep the Dolphin Wave Robot Pool Cleaner out of the reach of children Only an original power cable must be used at all times Replaced by a Dolphin Wave Robot Pool Cleaner certified technician in case of need When lifting the Dolphin Wave Robot Pool Cleaner take care to prevent back injury gt gt ib The Dolphin Wave Robot Pool Cleaner is suitable for outdoor use not for residential pools Wave XL User Instructions 2 FCC STATEMENT NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed
10. v food Vo V 951800 1984 o saur Uinipew Ye o seu auly Bur eds s ur1 A V BLOGVTECI ou Aejag V Figure 10 Pool profile diagram padeys Je nfuejoay ad 00d weg 4 gt 8BLIAGTECI w 91949 User Instructions Wave XL 10 Manual procedure for configuring pool profiles 1 From the Wave screen press Menu 2 From the Main Menu screen with Poo Pool A Profil Profile highlighted press Select and then ur TA modify to display the current active profile screen Cycle Time 3h 3 Using the Select and scroll buttons W A Esl RES set each parameter in turn Scan Mode Criscros R Select Back Figure 11 Pool A menu first screen 4 Press Select to enter the Pool Length Setup screen 5 With Pool Length highlighted press Select 25 30 35 40 50 60 The Pool Length Set Up screen is displayed Pool Length Set Up Meters 6 Using the arrows lt gt select the desired pool length Press Select and scroll down to ft b the next parameter Cycle Time Back Cycle Time determines the duration of each cleaning cycle Figure 12 Pool length setup screen Scannig Mode 7 Set each parameter and then scroll down to CresGross the next line Lines to Scan 8 Set Pool Type and choose either Rectangular Default or Shaped Rectangular Recommended for pools with parallel walls and 90 L shape Shaped Recommended for free formed pools Pool with Obstacles
11. The robot starts its cleaning cycle and the MMI displays the Countdown screen Figure 4 Figure 4 Countdown screen for 4 hour session The countdown screen shows that a 4 hour cycle time was selected and that the time remaining is 3 hours 59 minutes and 59 seconds At the end of the cleaning session the robot stops automatically To remove the robot from the pool proceed as explained in Removing the Robot from Swimming Pool on page 6 To avoid unauthorized changes to the MMI settings you can lock the MMI s keyboard From the Countdown screen press Lock Figure 4 To unlock the keyboard press POOL and then HOME in that order REMOVING THE ROBOT FROM THE SWIMMING POOL 1 Press HOME The robot starts moving in the direction of the floating cable Roll the floating cable neatly on the cable roller using the cable roller handle 2 Holding the floating cable gently pull the robot upwards and towards the Caddy As it reaches the side of the pool pull the cable gently until the floating cable handle emerges Grasp the handle and pull the robot out of the water The robot shuts down automatically By using the remote control you can drive the robot to the Caday Outside the pool do not pull the robot towards the Caddy by rolling up the floating cable with the cable roller handle Manual stop control If necessary you can stop the robot during the cleaning session Manual Stop 1 From the Countdown s
12. WAVE 300 XL EN User Instructions by m ayt fe ale i 8151452 EN Wave 300 XL User Instructions Table of Contents T SAFETY PRECAUTIONS irnos 2 2 POS STATEMEN Lesson ies 3 3 INTRODUCTION 3 4 CONTENTS 3 Assembly Instac VOTIS vrai iia 4 5 MMI GENERAL NOTES An Aaa 5 6 DEFAULT SETTING FOR CLEANING SESSIONS L l rire 5 Starting a cleaning rtr erro epu Raya n i 5 7 REMOVING THE ROBOT FROM THE SWIMMING POOL 6 Manual stop FN itp NN 6 p CUSTOMIZED SETTINGS n qd Rp bita EA ad 7 MM ers PM aad akad 7 Main menu 8 9 CONFIGURING ADDITIONAL POOL PROFILES 9 Manual procedure for configuring pool profiles 10 11 Starting cleaning operations siii ada dias 12 TO OPERATING GUIDELINES 13 EE EE ads 13 L FE REMOTE CONTROLUN 13 12 TROUBLESHOOTING Lande 15 Wave XL User Instructions 1 1 SAFETY PRECAUTIONS Please adhere strictly to the following warnings Do not operate the Dolphin Wave Robot Pool Cleaner when there are people in the swimming pool When examining the Dolphin Wave Robot Pool Cleaner disconnect the main power supply Risk of electric shock Connect only to a ground type receptacle protected by a ground fault circuit interrupter GFCI Contact a qualified electrician if you cannot verify that
13. ave screen figure 8 opens in the home window 4 Position the Caddy with robot about 0 5 1 0m 1 5 3ft from the pool s edge with its sloping edge facing the swimming pool ensuring that the floating cable is facing the direction of the Dolphin Wave power supply unit Starting a cleaning session Pool Length Set Up 25 30 35 40 50 60 Meters ft gt back Figure 3 Pool Length Setup screen Wave XL User Instructions Remote Wave Keyboard Control Unit Home Buttons Screen Figure 2 The Dolphin Wave robot MMI console On the MMI press POOL The robot will start moving towards the pool while pulling the floating cable and enter it and position itself on the pool floor Wait for the WAVE screen to appear In every activation of the robot it will straighten itself vertically to the wall of the starting point the robot will start moving backwards to straighten itself and then will continue in straight lines Press Start Please select pool length will appear on the screen After 2 seconds the Pool Length Setup screen appears 5 Using the arrows 4 gt select the required pool length Press Set For ft measure units continue scrolling to the Ane eycle right using b arrow CHSSCIOSS 6 Press Start The cleaning session will begin The factory default settings are used In order to change parameters refer to Configuring Additional Pool Profiles on page 9 03 59 59
14. ave robot is designed to handle 4 different swimming pool configurations and when these are set the pool configurations are stored in the MMI s memory The robot is preset in the factory with specific default pool settings which can be reset Please refer to the first Main Menu screen Figure 6 and Customized Settings page 7 4 CONTENTS Carefully remove all the items from the shipping box and check them against the packing list You should have Documentation and accessories Un assembled Caddy for storing and carrying the Dolphin Wave robot MMI console includes remote control unit Dolphin Wave robot and floating cable Filter Bags 2 fine porosity filter bags assembled in the Dolphin Wave robot for day to day cleaning 2 ultra fine filter bags for fine dust particles 2 loose weave filter bags for rough debris Power supply unit Wave XL User Instructions 3 Assembly instructions Refer to Figure 1 1 Attach the Caddy handle to the Caddy base and fasten with the 4 screws and 4 nuts provided 2 Attach the cable roller to its place and fasten with 2 screws Note the location of the connection cable between power supply and cable roller 3 Place the Dolphin Wave robot on the Caddy in front of the power supply as shown in Figure 1 4 Connect the MMI communication s cable to the power supply unit 5 Connect the connection cable between power supply and cable roller MMI
15. creen Figure 4 press Stop The MMI screen displays the message Stopping robot please wait After 5 seconds the Manual Stop screen Filter Bag is displayed Figure 5 Completed Time Total Hours 2 To stop the cleaning session completely press Exit The MMI display returns to the Wave screen Figure 5 Manual Stop screen Wave XL User Instructions MMI Alerts Filter bag This LED will light up when the filter bag is full and needs cleaning at the end of the cleaning cycle You are not required to immediately stop the operation The LED indicator will automatically reset on the next operation with a clean bag Alert LED will light up as an indication of an error that stops the robot Generally inspect the robot to locate the problem and re operate If the error repeats itself details of the specific error will be displayed on the MMI screen Refer to the Troubleshooting section at the end of this manual Loose weave filter bags are provided as an option to be used to collect large debris They should also be used in cases of sand accumulation in the pool 8 CUSTOMIZED SETTINGS The Dolphin Wave robot is controlled from the MMI console You can customize the robot s settings to match the specific type of swimming pool that is to be cleaned 4 different swimming pool configurations can be set and stored in the MMI s memory for future use When you configure a pool profile you ca
16. n also set the cleaning cycle time and the delay time before the robot starts its cleaning cycle The procedure for configuring additional pool profiles is explained in Configuring Additional Pool Profiles on page 9 The MMI keyboard procedures are explained in the next section MMI Operation Use the control buttons 6 8 8 amp located on the MMI below the screen to activate the various commands Use the MMI functions that appear in the various screen displays to navigate between the screens and to configure the software MMI Functions Menu From the Wave screen press Menu to display the Main Menu screen A Scroll up v Scroll down Start 1 Press both green buttons simultaneously to start pool cleaning Select Press Select to confirm your selection after using the scrolling buttons Modify Press Modify to change settings after making a selection Back Press to return to the previous screen Exit Press to return to the Wave screen Wave XL User Instructions 7 Defining the robot s parameters 1 Switch on the power supply The MMI Wave Main Menu screen opens in the home window Pool Profile 2 Press Menu to enter the Main Menu Filter State Figure 6 Technician Mode Statistics Select Figure 6 Main Menu screen There are 2 Main Menu screens and you access the nl Main Menu second screen by pressing the scroll down arrow W Clock Setup After Statistics scroll down to the second Main Date Se
17. rking hours or 1 year the earlier of the two Awarning message to perform PM will appear on the MMI screen when applicable It is obligatory that PM service be performed Please contact your dealer Failure to perform the PM service will void the warranty 11 THE REMOTE CONTROL UNIT The remote control unit RCU is located on the MMI console and held in position by a magnet Pull it upwards gently to remove it from its base When the robot is in automatic operation use the remote control to override the robot s programmed direction settings When the robot is moving in a forward direction the floating cable follows the robot from its tail end h The remote control unit has a control range of 50m 164ft from the Caddy hal Wave XL User Instructions 13 Using the remote control unit 1 To activate the remote control unit press the touch pad as indicated in the diagram Four activation lights will light up Forward On the spot 2 Press the forward arrow briefly The turning robot will start moving in a forward direction To stop the forward movement briefly press and release the forward arrow Backwards 3 Press the backward arrow briefly The robot will start moving in a backward direction To stop the reverse movement briefly press and release the backward arrow Touch pad On Off switch Figure 16 The remote control unit
18. tion proceed as follows 1 Go to the Wave screen Pool A is ES displayed as the currently defined setting Menu F Start l fan as shown in Figure 8 2 From the Wave screen press Pool A The Pool Profile screen opens Figure 9 Figure 8 Wave screen showing Pool A as default setting 3 To select a second pool profile scroll down Select Pool to Pool B and press Select The Wave screen automatically displays showing that Pool B is the currently defined pool Pool A Pool B 4 To configure Pools B C and D go to Step 1 Pool D of Starting a cleaning session on page 5 Select Figure 9 Pool Profile screen To go to a previously defined pool setting 1 From the Wave screen press the currently displayed pool setting at the right side of the screen see Figure 8 to open the Poo Profile screen 2 Scroll to the required pool and press Select The Wave screen is displayed with the chosen pool setting Wave XL User Instructions 9 Manual procedure for configuring pool profiles yoeg A v jes 1464 o saul ya o seur V s sajoe sqo yum oa UBIS saul SSOJOSSHD n Buiuue s q gt 11 BLOGVTECH S4 lN ujBue jood xoeg v 199 yoeg A 1u8u o seur ya o sour 9 01d y jood UINIPIN Buloeds seur1 euin ejdsig nu ul ajljoid v food poul UEIS adh 00g ajokg y Bua ood nu ul ajljoid
19. tu Menu screen Figure 7 Error Report Language English Select Exit Figure 7 Second Main Menu screen Main Menu Parameters The parameters that can be accessed from the Main Menu screen are explained in the table below Pool Profile Press Select to go to the Pool Profile screen The Pool Profile opens the Pool Profile screen and displays the 4 different Pool Profiles configured Pool A is the default setting Filter State Reports on the filter s condition Clean Filter bag is ready for use Full Change clean filter bag The filter bag warning light on the console will also indicate that the filter bag needs cleaning Technician Technician screen with restricted access Mode Statistics Press Select to review data on robot s usage Second Main Menu screen parameters Clock Setup Press Select to enter the Clock Setup screen and 12 24 hour mode Date Setup Press Select to enter the Date setup screen Error Report Displays information for service technicians Language Language interface mode Wave XL User Instructions In order to return to English from any other language press and hold the menu button for 3 4 seconds on the Wave screen 9 CONFIGURING ADDITIONAL POOL PROFILES The Dolphin Wave can be configured for 4 different pool profiles The configured settings are stored in the MMI s memory This section describes how to configure additional pool settings To add a new pool configura
Download Pdf Manuals
Related Search