TDB-120 - User manual
Contents
1. AND GENE for PCR analyses for temperature ENGINEERING CELL BIOLOGY stabilisation in DNA RNA restriction and denaturation reaction e BIOCHEMISTRY for the enzyme processes analyses e MICROBIOLOGY for the anaerobic microorganism cultivation e CHEMISTRY for the preliminary heating of reagents in chromatography especially when analysing chemical and biological components of fatty acids which condense in cold microsyringes 3 1 3 2 Getting started Unpacking Remove packing materials carefully and retain them for future shipment or storage of the unit Examine the unit carefully for any damage incurred during transit The warranty does not cover in transit damage Complete set Package contents TDB 120 Thermostat with lid and aluminium block ssassn POWON CONG oss fesises cond serre aean Arana aeee a ean ai aaee EEA spare fuse inside fuse holder Operating manual Certificate asnon arisi Setup place the unit upon even horizontal non flammable surface at least 20 cm away from any flammable materials remove protective film from the display plug the power cord into the socket on the rear side and position the unit so that there is easy access to the power switch and the plug 4 Operation Recommendations during operation Don t heat the tubes over the melting point of the material they are made of Remember that thin walled tubes have a higher thermoconducting factor Please check the2. D Medical Biological Research amp Technologies TDB 120 Dry Block Thermostat Operating Manual for versions fi V 1AE Certificate wane V 2AE V 2AD Contents Safety Precautions General Information Getting Started Operation Specifications Maintenance Warranty and Claims 2 Noa wn Declaration of Conformity 1 Safety Precautions The following symbols mean A Caution Make sure you have fully read and understood the present Manual before using the equipment Please pay special attention to sections marked by this symbol A Caution Surfaces can become hot during use GENERAL SAFETY Use only as specified in the Operating Manual provided The unit should be saved from shocks or falling After transportation or storage keep the unit under room temperature for 2 3hrs before connecting to electric circuit Use only cleaning and decontamination methods recommended by the manufacturer Do not make modifications to the design of the unit ELECTRICAL SAFETY Connect only to electric circuit with voltage corresponding to that on the serial number label Do not plug the unit into an ungrounded power socket and do not use an ungrounded extension lead Ensure that the switch and the plug are easily accessible during use If liquid penetrates into the unit disconnect it from electric circuit and have it checked by a repair and maintenance technician Disconnect the unit from electric circuit before mov
3. ators and closed laboratory rooms at ambient temperature from 4 C to 40 C in a non condensing atmosphere and maximum relative humidity 80 for temperatures up to 31 C decreasing linearly to 50 relative humidity at 40 C 5 1 Temperature specifications Setting RAMOS erheen tae eepe e E eee 25 C to 120 C Control rang cccccecceeeeneeeeeeeeeeeeeeeeeesenenees 5 C above ambient 120 C Setting reSOlUtion ccccecceecceeeeeeeeeeeeeeeeeeneeeeeeseaeeeeeeeseaeeeeseseeeeeeteees 0 1 C Stabilt at FIr Ca e r edad ei aves Meret a ees 0 1 C Uniformity at 37 Q sssrini astmai a aai 0 1 C Over temperature protection cceeeeeeeeeeeeeeeee internal thermal breaker General specifications Digital time setting range ccccccesseeeeeeeeeneeeeeeteseaeeeeeeeeeeees 1 min 96 hrs Display saenga ana teas tate ean ee Masetianietctelancs LCD 2x16 signs DIMENSIONS srein rna NEA 230x210x110 mm Working voltage ceccesceeeeeeeeeeeees 120 V 50 60 Hz or 230 V 50 60 Hz Consumed power 120 V 230 V ese 200 W 1 7 A 200 W 870 mA Weini aesir ete acth ieee ete N N eee a eee 2 8 kg Accurate within 10 TDB 120 with the built in block Catalogue number A 53 21 x 0 5 ml 32 x 1 5 ml tubes BS 010401 PAA A 103 21 x 0 5 ml 32 x 1 5 ml 50 x 0 2 ml tubes BS 010401 QAA Biosan is committed to a continuous programme of improvement and reserves the right to alt
4. er design and specifications of the equipment without additional notice 6 1 6 2 6 3 Maintenance If the unit requires maintenance electric circuit disconnect the unit from electric circuit and contact Biosan or your local Biosan representative All maintenance and repair operations must be performed only by qualified and specially trained personnel Standard ethanol 75 or other cleaning agents recommended for cleaning of laboratory equipment can be used for cleaning and decontamination of the unit Fuse replacement Disconnect from electric circuit Remove the power plug from the rear side of the unit Pull out the fuse holder by applying leverage in recess Fig 2 A Remove the fuse from the holder Check and replace with the correct fuse if necessary M 2 A for 230 V or M 4A for 120 V type M time lag Medium Fig 2 Fuse replacement 10 TAs 2 7 3 7 4 Warranty and Claims The Manufacturer guarantees the compliance of unit with the requirements of Specifications provided the Customer follows the operation storage and transportation instructions The warranted service life of unit from date of delivery to the Customer is 24 months Contact your local distributor to check availability of extended warranty If any manufacturing defects are discovered by the Customer an unsatisfactory equipment report shall be compiled certified and sent to the local distributor address Please visit www bi
5. ing Do not operate the unit in premises where condensation can form Operating conditions of the unit are defined in the Specifications section DURING OPERATION e Use only tubes of standard size e Do not check the temperature by touch Use a thermometer e Do not leave the operating unit unattended e Do not operate the unit in environments with aggressive or explosive chemical mixtures Please contact manufacturer for possible operation of the unit in specific atmospheres e Do not operate the unit if it is faulty or has been installed incorrectly e Donotuse outside laboratory rooms BIOLOGICAL SAFETY e Itis the user s responsibility to carry out appropriate decontamination if hazardous material is spilt on or penetrates into the equipment 2 General Information TDB 120 Dry Block Thermostat has been designed for heating and maintaining the set temperature in the aluminium block with special sockets for tubes TDB 120 Dry Block Thermostat has obvious advantages when working with the microquantities of the reagents used in the microtubes The device possesses unprece dentedly high precision and uniformity of temperature distribution over the block Two models are available offering a choice of tube configurations to meet the needs of many standard laboratory procedures e BlockA 53 21 x0 5ml 32x 1 5 ml microtubes e BlockA 103 21 x 0 5 ml 32 x 1 5 ml 50 x 0 2 ml microtubes The TDB 120 device is applicable in e MOLECULAR
6. n independent timer for convenient control over the sample incubation time Use the A and W Time keys Fig 1 5 to set the required time in hours and minutes hr min using as a guide the set time readouts shown in the upper line of the display Fig 1 1 Pressing the key for more than 2 s will increase the increment Press the Run key Fig 1 7 to start the timer The elapsed time will be indicated in the lower line of the display Fig 1 2 After the set time elapses the timer will give a sound signal and the blinking STOP indication will be shown on the display Press the Stop key Fig 1 8 to stop the signal Caution Stopping the timer does not stop the heating temperature maintenance process The heating can be stopped by reducing the temperature below 25 C using the Y T C key Fig 1 6 OFF indication will be shown on the display fig 1 3 The timer can be stopped before the set time elapses if required by pressing Stop key Pressing the Run key again will restart the timer with the same set time interval The set time interval can be changed at any time during the timer operation just stop the timer and make the changes required If the working time is set to 00 00 the unit will operate non stop After finishing the operation turn OFF position O the unit with the power switch at the rear panel and disconnect the unit from electric circuit 5 Specification The unit is designed for operation in cold rooms incub
7. osan lv Technical support section to obtain the claim form The following information will be required in the event that warranty or post warranty service comes necessary Complete the table below and retain for your records Model TDB 120 Dry Block Thermostat Serial number Date of sale Declaration of Conformity Declaration of Conformity Equipment name TDB 120 Type of equipment Dry Block Thermostat Directive EMC Directive 2004 108 EC Low Voltage Directive 2006 95 EC RoHS 2011 65 EC WEEE 2002 96 EC amp 2012 19 EU Manufacturer SIA BIOSAN Ratsupites 7 build 2 Riga LV 1067 Latvia Applied Standards EN 61326 1 Electrical equipment for measurement control and laboratory use EMC requirements General requirements EN 61010 1 Safety requirements for electrical equipment for measurement control and laboratory use General requirements EN 61010 2 010 Particular requirements for laboratory equipment for the heating of materials We declare that this product conforms to the requirements of the above Directive s N me WW Signature Svetlana Bankovska Aleksandr Shevchik Managing director Engineer of R amp D 12 20 Ad 06 204 SS 11 Biosan SIA Ratsupites 7 build 2 Riga LV 1067 Latvia Phone 371 67426137 Fax 371 67428101 http www biosan lv Version 1 2 04 January 2015
8. tubes before using be sure that tubes are thermoresistant e Tube caps can open under the action of high temperature gt 85 C thus causing sample volume shrinkage or potential health risk when working with infected material To prevent such cases it is recommended to use tubes with cap lock of Safe Lock type e Do not fill tubes more than 3 5 mm over the level they are immersed into the heating block Time hr min Temperature C TDB 120 Dry Block Thermostat Fig 1 Control panel 4 1 Connect the power cord to a grounded power socket and switch ON position 1 the power switch located on the rear panel of the unit 4 2 The unit will turn on and the following readouts will be shown on the display previously set time and temperature in the upper line Set timer indication STOP and current temperature in the lower line Actual 4 3 Temperature setting Use the A and W Temp keys Fig 1 6 to set the required temperature using as a guide the set temperature readouts shown in the upper line of the display Fig 1 3 Pressing the key for more than 2 s will increase the increment 4 4 The unit will start heating The actual temperature is shown in the lower line of the display Fig 1 4 4 5 When the required temperature is reached open the heating block lid and place tubes into the block sockets 4 6 4 7 4 8 4 9 4 10 4 11 Timer setting The unit is equipped with a
Download Pdf Manuals
Related Search