Passive single channel analog signal TXXXXB
Contents
1. FEATURES MORNSUN e2 port isolation signal input and signal output Passive single channel analog signal High accuracy 0 1 F S Isolation barrier lin amp lout e High linearity 0 1 F S e Isolation voltage 83KVDC 60S 111008 e Low temperature drift 35PPM C e Industry class Operation temp 25 C to 71 C e High reliability MTBF gt 500 000 hours PART NUMBER SYSTEM GENERAL DESCRIPTION TXXXXB Analog signal isolation barrier is a signal conditioner with electrical insulation between input and output it can receive a variety of analog signal from the field instrument and transmit a Package standard output signal or user specified special signal to the Isolation power output control room or DCS The product is isolated between power a iad supply input and output It is widely used in the industrial Input measurement systems medical electronic equipment electrical Isolation amplifier equipment etc Adopting high efficiency electromagnetism isolation technology to achieve signal isolation it is available to keep high output accuracy good linearity and low temperature drift SELECTION GUIDE T1100B NONE 4 20mA 4 20mA NONE O ae ELECTRICAL CHARACTERISTICS Output Signal Output Load ability 3000 Output 20mA Load Regulation lt 0 05 meas val 1000 TRANSMISSION CHARACTERISTICS Zero Offset 0 1 F S Gain Error 0 1 F S Temperature drift coefficient 0 00385 F S2. C 25 C to 71 C ISOLATION CHARACTERISTICS Galvanic Isolation Two port isolation signal input and signal output Isolation Voltage 3kVDC Tested for 1minute and leakage current lt 1mA humidity lt 70 Insulation Resistance 100MQ 500VDC Between signal input signal output power supply and isolation power output The copyright and authority for the interpretation of the products are reserved by MORNSUN T1100B 2013 07 09 A 2 Page 1 of 3 OTHER CHARACTERISTICS Operation temperature 25 C to 71 C Ambient Temperature Transport and Storage temperature 40 C to 85 C Safety Class IP20 IEC 60529 EN60529 EMC compliance GB T 18268 IEC61326 1 Weight 60g typ Application Environment No dust fierce vibration impulsion and corrosive gas Note 1 All specifications measured at TA 25 C humidity lt 75 the value of nominal input and rated output load unless otherwise specified 2 Only typical models listed specifications of custom product may be different Please contact our service people directly for certain conditions APPLICATION CIRCUIT DIAGRAM amp PIN DESCRIPTION gt Input gt 5 4 gt i lin Output Oe gt CONNECTION 1 Cross section area of wiring 0 5mm 2 5 mm 2 Multi strand wire the length of bare wire is about 8mm fixed by the M4 bolt APPLICATION NOTE 1 Please read the user manual carefully before using If any question please contact our FAE 2 Please do not
3. NC Power out i Note iiaa ai 25 00 0 984 Small white box L W H 165 155 40mm Note Packaging Quantity 2pcs Unit mm inch Inner carton L W H 425 175 160mm General tolerances 0 50 0 020 THIRD ANGLE Packaging Quantity 20pcs eases oy Note 1 All specifications are measured at Ta 25 C humidity lt 75 the value of nominal input and rated output load unless otherwise specified 2 In this datasheet all the test setup and methods are based on our corporate standards 3 All characteristics are for listed models and non standard models may perform differently Please contact our technical support for more details 4 Please contact our technical support for any specific requirement 5 Specifications of this product are subject to changes without prior notice MORNSUN Science amp Technology Co Ltd Address No 5 Kehui St 1 Kehui development center Science Ave Guangzhou Science City Luogang district Guangzhou P R China Tel 86 20 38601850 Fax 86 20 38601272 E mail info mornsun cn Hitp www mornsun power com The copyright and authority for the interpretation of the products are reserved by MORNSUN T1100B 2013 07 09 A 2 Page 3 of 3
4. use this product in hazardous area AFTER SERVICE 1 Products are carefully inspected and quality controlled during production and before shipment If they operated abnormally or there was anything wrong please contact our agent from which you purchased or MORNSUN FAE as soon as possible 2 MORNSUN warranty our product for 3 years from manufacturing date During this period MORNSUN will repair or replace the product if product was found to have manufacturing defect INSTALLATION amp DISASSEMBLY DIN35mm standard rail installation 1 Use a screwdriver Width of edges6mm cut in the metal card lock from 1 Upside of the instrument card in the rail the underside 2 Push underside of the instrument into the rail 2 Boost up the screwdriver and prize the metal card lock downwards 3 Pull the instrument out of the rail _ The copyright and authority for the interpretation of the products are reserved by MORNSUN T1100B 2013 07 09 A 2 Page 2 of 3 PACKAGING DIMENSION amp PACKAGING DIAGRAM i PIN CONNECTION Pin Function 3 Signal output 4 Signal output 5 Signal input Power in z ING 2 NO 6 Signal Input Signal out Others NC 3 4 D e g AR a gi k MORNSUN 2 o gt s33 oO G om Isolation Amplifier T1100B 5 6 Signal in 7 NC 8
Download Pdf Manuals
Related Search