B2K PDS - 141PAINTBALL
Contents
1. NCoMhity Zip Postal Code Email Telephone Date of Purchase Place of Purchase If you wish to register by mail you should copy this page fill it out and mail it to Indian Creek Design Inc 1019 First Street North Nampa Idaho 83687 Or You may copy this page fill it out and fax it to 208 468 66502. Tilt the marker so that the loader is upside down and beneath the pos the marker 5 Remove the paintball loader from the direct vertical feed tube PA ing the loader in a clockwise direction 6 Inspect the inside of the direct vertical feed tube to be sure A a ball does not remain inside the breech aw N A MAINTENANCE AN CAUTION Before attempting to perform any maintenahce operations or any marker disas sembly make sure that all paintballs and the propellant source have been removed from the marker Install the barrel blocking devices push the on off switch to the OFF position and keep the marker in its SAFE mode Simple Maintenance Keep your B2K PDS clean and lubricated to eliminate the friction that would prevent reliable operation Clean and lube the marker before each use and do not put it away dirty USE NO OILS Do not use petroleum basgd lubricants in the lubrication of this marker Teflon or silicon spray lubricants are the re ommended types of lubrication for the bolt area of the main housing Lithium grease isf f cdmmended for lubricating the regulator pistons and the cylinder assembly Be sure it iSsLithium Grease and not axel grease Cleaning Paint from the Batreh 4 Unscrew the barrel with approximately one and one half 1 1 2 revolutions to remove the barrel for swabbing cleaning Keep the barrel clean to insure the continued accuracy of the B2K PDS Gelatin fr th Paintballs has a tendency to b
3. dealers afffffates or agents will not be liable under this warranty nor under any state or federal law r the common law or otherwise for any dam 1 LED functions but the marker does not fire age or failure including personal injury fEsulting from such use and or alteration This war ranty gives you specific legal nant ere you may also have other rights that may vary from 2 Alternately missed shots state to state x 3 Velocity drops while firing several shots For warranty parts service or information contact Indian Creek Design Inc 4 Erratic Velocities Jumps of 20 fps or more 1019 First Street North Nampa Idaho 8368 5 Unexplainable paintball breakage 208 468 0446 4 NN 6 Slight leak from the solenoid in the back of the grip Or visit www i dpaintball com a Change the battery The LED only requires 1_ volts to function The solenoid NO lt requires a minimum of 5 volts to operate This means the marker may appear to be getting enough power when it is not All batteries are NOT created equal Performance will vary Therefore if you experience any erratic behavior always change the battery first LIMITED WARRANTY gt The manufacturer warrants the replacement of any original part due to defect in matefials and or workmanship of this air marker This warranty will be in effect for twelve az months for parts and twelve 12 months for labor following the original date of purch s dorthe orig inal purc
4. the grip battery area Reason the 4a valve is leaking a Tighten the 4 way valve to the manifold Take care not i over tighten b Check for over pressurization from the low ieee A Re adjust the low pressure regulator c Replace the O rings on the cylinder assembly ao ots d Replace the piston O ring Sized 011 ON e Replace the solenoid valve assembly mN Ball Breakage Problems 1 The ball breaks in the breech a Ball breakage is often caused by poor quality paintballs Make sure you always use fresh high quality paintballs b The balls in your loader can bind messing up your trigger timing Note Always use an agitated loader c As you run and shoot you actually Waweigh the gravity fed balls in your loader This can cause a ball to hesitatelin its drop This affects your trigger timing d If the ball retention O rings d hotmove freely the paintballs will crush against it or it may have stuck in the Gepressed position allowing double feeding Check their tension regularly andk ep this area as clean as possible e If the ball retentionMO ings are too sloppy the ball will not be held in the proper position This maya allow the next ball to enter the path of the bolt subjecting it to impact VAD for shearing Verify the tension of the O rings Regulator Related Pfoblefns 1 The gauge sea carrecily when charged but climbs in pressure after a few moments af The fequiator seal has been contamin
5. If you have an adjustable tank regulator the input pressure from your tank should be set at 350 500 PSI Higher input pressures will not provide increased performance 2 If you have a fixed output regulator on your tank pre set then you may have to re adjust the pressure shown on the gauge using the method discussed previously 3 If you plan to use CO2 then please use an anti siphon tank and a filter Low pressure regulator adjustment Velocity adjustment The low pressure regulator is externally adjustable via the adjustment screw with the slot for a wide screw driver or even a quarter in the front of the low pressure regulator The low pressure regulator is pre set at the factory to 85 95 PSI to operate the 4 way solenoid actuated valve It may be necessary to re adjust the low pressure regulator from time to time to achieve desired velocities Bench adjusting the regulator can be done by pressurizing the marker be sure the input regulator is set properly and then turing the adjustment screw inward clock wise until you hear a leak coming from the 4 way valve in the grip area The 4 way valve has an over pressurization relief valve that will start to bleed off at approximately 125 PSI once you hear the leak start then back off the adjustment screw 2 tum and the leak will stop That will approximate the pressure to about 90 PSI The low pressure regulator is designed to shut down and preserve the integrity of the low pressure system if it
6. K PDS for any reason the box in which you purchased the marker _ is acceptable to all major carriers Never ship charged CO2 or pressurized gas containers y ADJUSTING THE TRIGGER PULL You will notice three 3 screws in your trigger These screws adjust the length of ptill actu ation point and spring tension of the trigger The bottom screw adjusts your trigger stop point length of pull The top screw is the contact point for your micro switch or actuation point The center screw is the spring tension adjustment screw J 1 Use blue loctite while adjusting the screws Normal activity can Auss he screws to back out of adjustment DO NOT glob the loctite on it can cause daade to the micro switch if you use too much 2 Begin by adjusting the bottom screw to your desired pall Noes it in to lessen the dis tance the trigger must travel NN 3 Very Carefully screw in the top screw Making large Sydiments can force the screw into the micro switch and damage it You will want to screw it in to the point where it makes contact with the micro switch but does not p yhanently rest on it Continually check to verify that the LED flashes off and thena kof When you pull the trigger If you pull the trigger and the LED goes off and stays off you have adjusted the screw in too far Back it out 4 Adjust the spring tension by turning the screw in for more tension and out for less tension 5 Clean up any excess loctite and let it dry fo
7. PDS 6 3 04 10 39 AM Page 5 Be2eK PDS USER MANUAL OPERATION Read the entire manual before you prepare your B2K PDS for firing Safety and safe mark er handling are the most important aspects of paintball sports Please practice each of the following steps with an unloaded marker before attempting to charge your marker with com pressed air and paintballs Do not load compressed air and paintballs into your B2K PDS until you feel completely confident with your ability to handle your B2K PDS safely Keep your finger out of the trigger guard and away from the trigger point the muzzle of the marker in a safe direction at all times Keep the marker turned off until ready to operate The B2K PDS does not have a mechanical safety only an on off switch Always keep your B2K PDS pointed in a safe direction Always use a barrel plug Installing the 9 volt Power Source The B2K PDS requires a single 9 volt battery as the electronic power source The use of long life batteries is recommended The 9 volt battery is located in the grip behind the trigger and below the on off switch The battery is accessed through the grip panel located on the left side of the marker Remove the 2 screws that hold the grip panel in place Connect the battery to the terminal and place the battery inside the frame carefully being sure that the black and red wites to the terminal are toward the top Make sure that there are no abrupt kinks and the Se are co
8. ated Disassemble the regulator and NO clean the seal with a Q tip and alcohol If you need assistance in the disassem N N bly of the regulator please call 208 468 0446 d P The gauge reads correctly when charged but drops in pressure after a few shots a The regulator may not be adjusted correctly Remove all pressurized gas and back off the regulator adjustment screw 3 turns Pressurize the system and adjust the pressure back up to the desired pressure b Slow regulator recovery can be directly related to the recovery time of the tank regulator All compressed air tank regulators are not created equally some may perform and some may not 3 The gauge reads correctly when charged but drops in pressure after a few shots and is slow to climb back to normal pressure a The recovery side of the regulator is sluggish and may need cleaning and lubrication If you need assistance in the disassembly of the regulator please call 208 468 0446 b The regulator seal needs to be replaced if it has a deep groove in it from the regulator cup c Slow regulator recovery can be directly related to the recovery time of the tank regulator All compressed air tank regulators are not created equally some may perform and some may not Replacing or removing the original regulators voids all warranties MANUAL PDS 6 3 04 10 39 AM Page 13 Be2eK PDS USER MANUAL Battery Related Problems The manufacturer its authorized
9. haser Such warranty service will be provided only if the warrantytegistration card included with this manual is filled in completely and on file with the manutactirer All other service will be duly charged for and returned via UPS C O D 7 4 The manufacturer will replace without charge any original part that is determined by Indian Creek Design Inc to be defective under the terms of this Warranty However shipping charges are not covered hereunder Failure due to an acbidSpt abuse neglect modifica tion normal wear operator error maintenance by other Maman authorized the manufactur er dealer or use of parts inconsistent with the use ay intended for the air marker as sold is not covered by this warranty J There are no other warranties or guarantees expressed or implied made by the manufac turer on this air marker The sole and exclusive liability of the manufacturer and or its authorized dealers affiliates or agents pursuant to this warranty will be for repair or replace ment of the defective part incidental or consequential damages are expressly excluded hereunder E MANUAL PDS 6 3 04 10 39 AM Page 15 BeK PDS USER MANUAL NOTES Warranty Registration A Please take the time to send in this wagrantyby mail or fax or go to www icdpaintball com registration htm for convenient online warranty registration PDS Serial Your Name Address Address City N State
10. mfortably placed do not force them into place Replace the grip panel and sords y If you need to remove the complete battery frame and grip follow these instructions Before removing the tray remove the grip frame side panel on the left side exposing the CPU and battery To remove the tray use a 7 64 hex wrench and remove the fOut 6 32X1 screws around the bottom of the tray Gently separate the upper section from the lower section being careful not to put stress on the wiring harness blue wires connected to the solenoid valve on the upper section Place the tray and upper body Togather being careful not to pinch any wires in the body bring the blue wire loop backito its original position Turn the main on off switch to the on position and be sure the LEDA hts up then turn off Replace the four 6 32X1 screws and the grip panel CO2 Nitrogen or Compressed Air Usage The B2K PDS comes with a female _ Puin fitting adapter on the input of the regulator The B2K PDS can be set up to use a nitrogen or compressed air system Although it may be used CO2 is not recommended for use as the propellant Adjustable regulator compressed air systems The input pressure from your compressedeair system should be regulated down to 350 500 PSI output pressure Note on MOST s Stems there is a large difference between the set ting pressure and the actual output operating pressure If your compressed air system does not have an ou
11. njury or death The manufacturer assumes no responsibility for physical injury or property damage resulting from the use of this marker LS V The manufacturer makes no warranties with respect to this NA nein and disclaims any implied warranties of merchantability or fitness for af Pariioular purpose The information in this document is subject to change without notice Ahewmanufacturer assumes no respon sibility for any errors that may appear in this document Z WARNING This is not a toy Misuse may cause serious injury or death Eye protection designed specifically for paintball must be worn by the user and persons within range Recommend 18 years of age or older to purchase Persons under 18 years of age must have adult supervision READ OWNER S MANUAL BEFORE USING B2K PDS OVERVIEW AA IRS Av The B2K PDS Paintball Detection Sytem is a high quality paintball marker specially designed to meet the needs of the professional style tournament player The B2K PDS is an electronic solenoid actuated computer controlled marker The major components of the B2K PDS are machined from solid aircraft grade aluminum and then hard anodized per mil itary specifications No castings are used in the construction of the B2K PDS thereby pro viding the end user with a high quality precision engineered marker The PDS paintball detection system is degighed to detect whether or not a paintball is seated in the breach ready
12. r at least an hour before using your B2K PDS This ensures the screws will remain in place B2K PDS TUNING GUIDE JA High pressure regulator adjustment A The B2K PDS has an innovative systema Jhe pressurized gas is regulated internally The pressure regulator is externally adjustable via the screw in the side of the high pressure reg ulator To increase the pressur use a 3 32 hex wrench inserted into the screw and turn clockwise NS gt NOTE Only slight t Tiel are Needed to accomplish changes in the pressure used to shoot the paintball To decrease HANA shown on the gauge turn the screw counter clockwise You must take a clearit Shot before the change in the decreasing direction can be registered A predsurdgduge has been installed into the regulator body to indicate the exact operating pre assure tof the marker This gauge is extremely useful At the factory we set the regulator Q gauge to 180 200 PSI with an input pressure of 400 PSI using Compressed air as the base propellant Under normal circumstances these settings will produce paintball velocities at approximately 280 300 fps The input pressure from your tank should be set at 350 500 PSI Higher input pressures will not provide increased performance There is a specific input side and output side of the main input regulator If the gauge and input sides are switched the outcome will be total bypassing of the main input regulator 1
13. s twist it off in a CLOCKWISE direction as well The B2K PDS uses 68 caliber water soluble paintballs The paintballs are gravity fed from the loader through the direct vertical feed nipple and into the breech of the marker MANUAL PDS 6 3 04 10 39 AM Page 7 Be2eK PDS USER MANUAL Firing the B2K PDS Keep your finger out of the trigger guard and away from the trigger point the muzzle of your marker in a safe direction at all times during this process Be sure your goggles are secure ly in place Push the on off switch into the off position Always keep your B2K PDS pointed in a safe direction Place the empty loader onto the marker Be sure that it is securely mounted in place Apply the compressed gas pressurizing the marker Put the paintballs into the loader Remove the barrel plug Aim the marker at the target Push the on off switch to the ON position the LED will light up Place your finger on the trigger Pull the trigger with a smooth squeezing motion BANG ONONAWD UNLOADING THE B2K PDS Keep your finger out of the trigger guard and away from the trigger point the muzzle of yours marker in a safe direction during this entire process Always keep your B2K PDS peer wD a safe direction 1 Install the barrel blocking device 2 Push the on off switch to the off position The LED will be off CA 3 Remove the pressurized gas from the marker carefully pee 4
14. sees an input pressure over approximately 400 PSI coming from the main input regulator This marker was designed with safety and safety standards in mind If you attempt to shoot paintballs at velocities higher than established safety standards the marker will not function properly MANUAL PDS 6 3 04 10 39 AM Page 11 Be2eK PDS USER MANUAL NOTE 1 You may notice that if you attempt to operate the marker at extremely high veloc ities the internals will not function properly NOTE 2 The B2K PDS is not designed to shoot above the safety limits established by industry standards Leak Related Problems 1 The B2K PDS has a leak down the barrel Reason gas is leaking through or around the valve pin seal or O ring area a Can you hear the leak when the gas is removed Yes There is no leak You hear the ocean b The valve seal is marred scratched or worn out or dirt has gotten to it Replace it 2 The B2K PDS has a leak around the high pressure regulator seam Reason the seal between the regulator body and the main body is bad a Tighten the regulator to the body b Check and or replace the O ring en k N 3 The B2K PDS has a leak around the low pressure regulator seam Reason the seal j between the regulator body and main body is bad or the regulator has loosened A a Tighten the regulator into the body b Check and or replace the O ring gasket Sized 019 af 4 The B2K PDS has a leak inside
15. sia IndianjCreek 52K PDS paintball detection system USERS MANUAL MANUAL PDS 6 3 04 10 39 AM Page 3 Be2eK PDS USER MANUAL INSTRUCTION MANUAL Version 2 1 Indian Creek Design BushMaster series Model B2K PDS Copyright 1993 2004 All Rights Reserved No part of this document may be copied or reproduced in any form or by any means without the prior written consent of the manufacturer Trademark Notices Panther VTS Panther II VTS Puma Bobcat Thunder CAT Desert FOX 45 68 Magnum VTS BushMaster 2000 BKO and BKO2 are all registered trademarks of Indian Creek Design Inc its assigns and or its distributors Notice is hereby given that this manual is part of the article owned in whole by the manufac turer known as indicated in this manual and drawings All rights of manufacture and repro N duction of such articles or any part thereof are reserved by the manufacturer Neither sajd article nor any part thereof may be manufactured or reproduced except by written authorize J tion from the manufacturer All proprietary rights and information are the sole property a manufacturer STATEMENT OF LIABILITY The manufacturer delivers this marker with the understanding that the A nutacturer assumes no responsibility for its resale or safe handling Misuse abuse Of failure to follow the manufacturer s instructions contained in this manual could result irf property damage bodily i
16. the link pin is engaged PROPERLY with the hammer if the link pin IS NOT PROPERLY replaced you may damage the hammer cylinder assembly Remember operator error is not covered by warranty MANUAL PDS 6 3 04 10 39 AM Page 9 Be2eK PDS USER MANUAL STORAGE AND TRANSPORTATION Your B2K PDS must be clear of all paint and propellant when not being used Be sure the on off switch is off and the LED is not lighted Put the barrel blocking device in place Make sure the marker is clean Store your B2K PDS in a clean cool dry place Keep your B2K PDS away from any unauthorized users Your B2K PDS must be clear of all paint and any source of propellant during transportation to and from the playing field Keep your barrel plug in place Keep the on off switch in the off position Protect your B2K PDS from excessive heat during transportation Observe and obey all local state and federal laws concerning the transportation of paintball markers For information concerning any of the laws in your area contact your nearby friendly law enforcement agency IMPORTANT Never carry your B2K PDS uncased when not on a playing field The non playing public and law enforcement personnel may not be able to distinguish between a paintball marker and firearm For your own safety and to protect the image of the sport always carry your B2K PDS in a suitable marker case or in the box in which it was shipped If you must ship your B2
17. to fire Ifa paintball iS not there it will not fire An on off switch has been provided for the PDS for the REN of dry firing and simply over riding the PDS Paintball markef amp get a lot of abuse Indian Creek Design Inc has built the B2K PDS with this in mind A internal parts wear and contact surfaces have been heat treated or hard anodized he toughest and most resilient materials and components have been used in the design Own marker h Th BAK PDS uses a single standard 9 volt battery for operation The circuitry is a micro processor based digital controller The B2K PDS does not need tools in order to field striped Removing the field strip link pin of the bolt enables the removal of the entire bolt assembly The B2K PDS offers low pressure operation The main operating pressure is 180 220 PSI nominally adjusted to visually via the gauge on the primary input regulator The secondary pressure is factory pre set and regulated to 85 95 PSI Gas usage is controlled through these 2 internal regulators One unique feature of this marker is the regulator adjustment This allows precise adjustment for the velocity control of the marker and for gas efficiency The B2K PDS comes with a removable barrel system This feature allows the user to select a barrel that is most suitable for the playing conditions All barrels are mirror honed with a step bore and straight and spiral tip porting and stock length is 12 MANUAL
18. tput pressure gauge en its regulator we do not recommend its use Fixed output regulated compressed air systems The B2K PDS will work just dig wwith a pre set tank You will get better performance from a lower output pressure t than af high 750 850 output VERIFY the output pressure from the regulator If your compr sseq air system does not have an output pressure gauge on its reg ulator we do not recomr erfd its use CO2 usage AA Although it may Be used CO2 is not recommended for use as the propellant Generally the CO2 that We uSe as an industry is industrial grade CO2 It is dirty pumped from large tanks full offeontaminates including rust and metal flakes CO2 can be used successfully if used with ant Bsiphon systems and filters Be aware that the use of CO2 may result in less than N opti De performance REMEMBER CO2 compressed air or nitrogen systems can be extremely dangerous if misused or improperly handled Use only properly certified cylinders Before pressurizing your BKO check to make sure that you have a barrel blocking device in place and there are no paintballs in the marker The on off switch should be OFF Air can now be applied the marker will become pressurized and the bolt will move backwards Paintball and Loader Usage The B2K PDS comes equipped to accept 1 03 OD standard gravity feed loaders Fit the loader directly into the vertical feed tube Always twist it down in a CLOCKWISE direction Alway
19. uild up in the barrel As part of your cleaning ritual Wash gut the barrel with hot soapy water and rinse it well PDS pamiwal een system Keep the refed emitters and detectors clean for your best results negova ne Bolt Assembly Field Stripping NK the paint and pressurized gas from the marker The marker can be field stripped while it is pressurize but this is not recommended 1 Install the barrel blocking device 2 Push the on off switch to the off position The LED will be off 3 Remove the pressurized gas from the marker carefully 4 Remove pull the knurled pin from the top of the marker Pull the bolt body out the back of the main body Once the bolt assembly is removed it is possible to clean the entire upper receiver of the marker including the breech and feed tube area You may slightly lubricate the rear section of the bolt and bolt chamber with a light synthetic spray lubricant before re installing the bolt Do not use petroleum oil based lubricants do use Teflon or silicon based lubricants The bolt is NOT a simple plastic it is a natural Delrin acetate material which is a Dupont 3M material developed specifically for this type of application The use of a metal type of bolt will void all warranties 1 Point the barrel downward and slide the bolt in until the link pin hole lines up with the slot in the hammer and carefully install the link pin 2 Carefully install the link pin Note You must be sure that
Download Pdf Manuals
Related Search