PTZCON manual
Contents
1. perimeter scan Adjust camera focus Adjust camera zoom 2 D Close open camera iris for non auto iris cameras Menu Esc button for navigating setup menu amp key lock Ot Show protocol and baud rate for current PTZ ID es Keyboard Functions PLEASE NOTE Availability of some features will depend on compatibility and specification of your PTZ camera Some controller functions may not be supported by your PTZ camera please check with the product manufacturer Function Function Camera set keys recall keys control keys Menu setup keys MENU SETUP KEYS Menu Hold for 3s to enter setup configuration menu 2 Enter password default 8888 See page 5 for further details Back Escape to previous menu exit menu Press once during normal operation to lock keys will not work in menu ae Show protocol and baud rate for current PTZ ID FUNCTION SET KEYS preset To store a preset camera position press 0 255 Preset rater To record a predefined movement pattern press for 3s All camera movements will be recorded exactly as per user input Press again to stop recording To set up a patrol points at preset camera positions presets must be defined first see Preset button Press Patrol choose the first preset position 0 255 then push joystick downwards to choose dwell time 0 255 then push joystick downwards to select movement speed 0 99 and push the joystick downw2. PTZLCON PAN TILT AND ZOOM CONTROLLER USER MANUAL www espuk com Product Overview FEATURES e Supports up to 255 PTZ cameras e Multiple protocols and baud rates supported across multiple PTZ cameras e LCD display e Control lock feature to deny unauthorised use e Supports Pelco D Pelco P Samsung Panasonic and HikVision protocols e Supports baud rates 1200 2400 4800 9600 19200 INSTALLATION OVERVIEW RS 485 Input Output Transmit Receive LED Power LED RS485 8XPORT T R PW pifefafs s dr le Ta To Ra Rb G oo Installation It is highly recommended that a screened cable is used to connect the RS485 control wires et from PTZ controller or interference may occur 1 Connect Ta to the RS485 on the PTZ camera s 2 Connect Tb to the RS485 on the PTZ camera s 3 Connect GND to the ground on the PTZ camera s if applicable 4 Connect the cable screen to GND 5 Set camera protocol s and baud rate s RS 485 EXPORT KEYBOARD OVERVIEW s Function Define a preset camera position Record new movement pattern will directly mimic user input Set up a patrol route based on preset camera positions positions must be defined by the user Turn auxiliary PTZ controllers on or off Patrol wW c o gt Select PTZ camera ID select a PTZ ID to control the associated camera Recall preset position Recall pattern Recall patrol Set camera to auto pan mode
3. ards to setup the next point in the patrol Once all points in the patrol have been set press Patrol FUNCTION RECALL KEYS To recall a specific preset camera position press 0 255 Shot Press to run recorded pattern To recall a specific patrol tour press 0 255 Patrol Configuration menu To enter menu press E for 1s then enter password default 8888 Use the joystick up down to navigate through menu tree Use the joystick left right to alter the current value where applicable Press to confirm select press Sto escape go back SYSTEM SETUP ADDRESS PTZ SETUP Menu Item Explanation SET PW Set 4 digit PIN to lock keypad DEFAULT Restore factory default settings SOUND SET Key tones on off ID SET Set keyboard ID when using multiple controllers LOCK SET Toggle key lock on off ADDRESS Sets protocol and baud rate for each PTZ camera Push joystick left right to select camera ID then press Push joystick up down to change between protocol baud rates push joystick left right to alter values Press to confirm Key Lock Function Key lock must be enabled from the menu see page 5 Key lock can only be engaged if not in setup menu Press then enter password PIN to lock keyboard Repeat process to unlock To reset a lost password please call ESP Technical Support on 01527 51 51 50 Warnings Do not disassemble product warranty will become void Only for use indoors i
4. n environments lt 95 humidity Only use the supplied 12V PSU Technical Specifications Protocol Pelco P Pelco D Panasonic HikVision Samsung RULE Dahua SAE Baud rate bps 1200 2400 4800 9600 19200 Max camera support 255 Controllers supported 16 in total 15 auxiliary Power supply DC 12V 10 Power consumption 6W MAX Working temperature 0 C 50 C Dimension 420 x 260 x 170mm Elite Security Products Telephone 01527 515150 Unit 7 Target Park Shawbank Rd Fax 01527 5151 43 Lakeside Redditch B98 8YN email info espuk com www espuk com
Download Pdf Manuals
Related Search