USER MANUAL SCC 2
Contents
1. Manifold Exhaust Temperature measured before turbo charger Page 14 of 28 500156 usermanual scc2 en 2 0 doc STEYRMOTORS INNOVATION ITH LIGHTNESS USER MANUAL SCC 2 5 2 1 Set Fuel Tank size Gear Ratio and Propeller Pitch Below screen will appear once the function key for menu Fuel is pressed a second time or pressed longer than 1 second The user can enter e the fuel tank size preset value 200 litre e the gear ratio preset value 0 the fuel tank limit preset value 20 litre NOTE An alarm will appear if fuel quantity in tank is below the set limit The icon for the fuel lights yellow e propeller pitch for slip calculation preset value 0 If gear ratio and propeller pitch are set to O preset values the slip calculation is off FUEL TANK SIZE FUEL TANK LIMIT 33 Page 15 of 28 500156 usermanual scc2 en 2 0 doc STEYRMOTORS e INNOVATION WITH LIGHTNESS Wesen USER MANUAL SCC 2 Procedure to change parameter values 1 Select required parameter with gt lt N 2 Select Enter J 3 Following screen with choice box will appear FUEL TANK SIZE 4 Enter required digit via buttons VA and quit with 5 If the total value for parameter is okay select button Yo and press ad Page 16 of 28 500156 usermanual scc2 en 2 0 doc STEYRMOTORS Q ITH LIGHTNES USER MANUAL SCC 2 5 3 Engine menu On this mask the engine related values are displayed2. 00 LOAD gauge Displays the load on the engine in percent Calculated from ECU via actual fuel injection quantity to max possible fuel quantity SLIP gauge e When no GPS input exist the gauge for SLIP shall not be displayed e See displayed gauge for SLIP in above illustration e See non displayed gauge for SLIP in below illustration NOTE The gauge SLIP is an indicator for the driving efficiency It is the ratio of actual velocity determined by GPS and the calculated velocity out of engine speed gear ratio and propeller pitch FUEL gauge Displays the actual fuel quantity in fuel tank NOTE Fuel quantity signal only to transfer via engine CAN BUS ASSUMED OPERATION RADIUS Displays the range in hour and kilometer NOTE Operation radius is only calculated if a fuel quantity via fuel gauge received ASSUMED FUEL CONSUMPTION Displays the fuel consumption in selected unit in Liter hour and selected unit in Liter 100 km Page 13 of 28 500156 usermanual scc2 en 2 O doc Fe USER MANUAL SCC 2 DENSITY and MET gauge When no Fuel Compensation Kit is installed or no fuel density message is received for 90 seconds the gauges bottom left and right will not be displayed see below illustration See displayed gauges in above illustration Unit ID 1650076 100 Al LOAD 0 FUEL It 100 ASSUMED OPPERATION RADIUS ASSUMED FUEL CONSUMPTION 0 0 h 0 km 0 0 itn 0 0 id Density Displays actual measured fuel density MET
3. 120 20 f s 90 16 2s 32 WATER C EXHAUST C BATTERY V 29 58 14 5 43 5 29 87 0 58 8 0 0 6 MAP PSI N Fuel PSI M USER MANUAL SCC 2 Unit ID Unit ID 1650076 NNOVATION WITH L Rs 24 ENGINE HOURS ENGINE ID Current time On the top left you can see the GPS information If you have connected a GPS receiver and it is receiving data you see this kind of information Without communication to the GPS the speed gauge the whole gauge including scaling etc and the current time shall not be displayed Unit ID The unit ID hardware number of the SCC2 shall be displayed top right Software Version The Software Version shall be displayed bottom left Current time Current time shall be displayed bottom right NOTE Only in combination with GPS input signal displayed Battery charge indication light Below 800 rpm the battery charge indication light won t appear The battery charge indication will appear under following circumstances e gt above 800 rpm e by a 24 V system the battery voltage may be below 25 0 V e by a 12 V system the battery voltage may be below 12 5 V Page 12 of 28 500156 usermanual scc2 en 2 0 doc STEYRMOTORS YRMOTORS USER MANUAL SCC 2 5 2 Fuel menu Below screen will appear once the function key for menu Fuel is pressed ASSUMED OPPERATION RADIUS ASSUMED FUEL CONSUMPTION 0 0 h 0 km 0 0 itn 0 0 M 800 800 600 DENSITY kg m3 10
4. Below screen will appear once the function key for menu Engine is pressed gt 48 04 20 N 14 25 44 E ENGINE NUMBER ENGINE HOURS _ ENGINEID 82340123 Dei Ru Engine coolant water temperature top left The bar will change color from green to red when temperature exceeds the tolerance programmed in ECU Software Exhaust temperature top middle The bar will change color from green to red when temperature exceeds the tolerance programmed in ECU Software Battery top right The gauge for battery voltage shall adjust the scaling automatically Vales Voliagerange 16V i2V Range 1eV PAV Range Boost pressure bottom left MAP Manifold Air Pressure Fuel pressure bottom right Engine Number Engine Hours Engine ID This information is sent automatically from the ECU Page 17 of 28 500156 usermanual scc2 en 2 0 doc ZF USER MANUAL SCC 2 STEYRMOTORS INNOVATION TH LIGHTNESS 5 4 Alarm menu Page 18 of 28 Below screen will appear once the function key for menu Alarm is pressed Clear Service Code 1314 Voltage of sensor LPS too low 4352 functional error of WAR button 1831 Voltage of sensor RPM too law 280 Voltage of sensor ECT too high 274 Voltage of sensor ACT too low 8745 Voltage of sensor MAP too high 600 Voltage of sensor RPOS toa low 396 Voltage af sensor FSP too low 4098 Voltage of sensor ITP too high 1315 Voltage of sensor LPS too high The Alarm
5. C 2 View back side ME1504010 Kit includes 1 P No 800732 STEYR CONTROL CENTER SCC 2 2 P No 701807 HARNESS SCC 2 a 0 2m Connection cable to b 3x Video inputs c 1x USB connection readout update d 1 5m Connection cable to e Engines instrument panel 4 pole Deutsch plug f GPS NMEA 2000 connector g 120 Ohm CAN terminator Connection to other instruments via 4 pole Deutsch plug and 120 Ohm CAN terminator T 3 P No 500156 USER MANUAL SCC2 Page 10 of 28 500156 usermanual scc2 en 2 0 doc STEYRMOTORS 2 USER MANUAL SCC 2 5 Display menus 5 1 Home menu Below screen will appear once the function key for menu Home is pressed Fuel 5 Alarm menu menu 87 0 ff 120 NS a m m Engine A 131 M OU Diagram menu menu 2000 0 5 RPM X 1000 menu C KEEP ENTER BUTTON PRESSED FOR CHANGING DAY OR NIGHT MODE Home The Home menu displays e Engine RPM Oil pressure Engine coolant temperature opeed of the vessel Note Only in combination with GPS input signal displayed For engine rpm and coolant temperature a warning range red range shall be displayed as shown in the above illustration The length of the red bar is adjusted automatically according the engine model in use Page 11 of 28 500156 usermanual scc2 en 2 O doc GPS coordinates 05 00 00 N 01 06 36 E 85 ENGINE NUMBER SCC2 Software Version GPS coordinates 55 20 28 50 o
6. INNOVATION WITH LIGHTNESS USER MANUAL SCC 2 4A DR BEN 014 2 7 44E P N 500156 Date July 2015 Issue 2 0 Language EN SCC 2 Software Version 1 3 X USER MANUAL SCC 2 STEYR MOTORS GmbH www steyr motors com Im Stadtgut B1 A 4407 Steyr Gleink AUSTRIA Page 2 of 28 500156 usermanual scc2 en 2 0 doc STEYRMOTORS N mk A 7 Dimensions for Installation 8 Technical Data Table of contents Table OEGODIGnliS uiii iiio eiusman caves aetuns E cui musa dE C rir e 2 1 Important safety and legal information 2 2 CGICAMING Me CISD ss ER EE RE EE De Ee ZO AOI CV le OMS Ms ese ee EE AE EE ER EE ie Re 2 4 Hardware Installation ese ee ee Ee EER EE ee ee EE ee ee RE ee ee ee ee ee Basie UN COINS MR ER EE EE Connecting the display c EER RR GEE RR RR ae EE EE BEI ass es oe ee Re ER EER ee ER ee Ee se ig ie se TONS O RE EE EE N 5 2 Fuel MENU ee ee ee ee ee ee ee ee ee ee ee ee ee ee 5 2 1 Set Fuel Tank size Gear Ratio and Propeller Pitch go geld MENU sa Ee n T 5 4 Alarm Menura Ee ee pax ee ee RE n FUA ados DU Re RE S9 Dladiam ie IE Eie OE 5 5 1 Change displayed parameter 5 6 l O Box menu ODOM sesse sies ek EN Ge De RR Gee ENG Ee ee ie 5 7 Display Settings MENU see ee ee RE EE ee Re EE ee ee ee ee ee 5 7 1 Day Night appearance Software update ec 6 1 Softwa
7. be found on the STEYR MOTORS homepage http www steyr motors com network STEYR MOTORS GmbH Im Stadtgut B1 A 4407 Steyr Gleink AUSTRIA www steyr motors com Page 28 of 28 500156 usermanual scc2 en 2 0 doc
8. c2 en 2 0 doc STEYRMOTORS YRMOTORS USER MANUAL SCC 2 The following engine parameters can be selected Short name Description EXT Engine Exhaust Gas Temperature T30 Page 20 of 28 500156 usermanual scc2 en 2 O doc USER MANUAL SCC 2 5 6 VO Box menu Option Select Pi gt output NS Unit ID 1650076 VO menu Page 1 or Page 2 Output ON ON OFF OFF Output 1 Output 2 To display the optional SCC l O Box menu update the SCC as described under chapter 6 2 Software update to display VO Box menu The value of each connected sensor is shown at the top otatus of outputs is shown at the bottom Selecting output gt 1 With the arrow buttons you can select between the outputs Output ON OFF Pressing the button the selected output can be switch ON OFF VO menu Page 1 Page 2 Pressing the button a second time VO Box menu page 2 appears Page 21 of 28 500156 usermanual scc2 en 2 0 doc USER MANUAL SCC 2 5 7 Display Settings menu Once the MENU Key see in below illustration is pressed the following will be displayed Following settings are to change Brightness selection Selection of time zone for GPS GMT is default value Temperature unit selection Speed selection Pressure selection Volume unit selection LOAD CONFIG see 6 2 Software update to display VO Box menu 5 7 1 Day Night appearance Between Day Night mode can be switched if Enter key see in below illu
9. ch or socket to tighten Torque lock nuts to 8 10 inch pounds Flush Mounting the Dash 1 Cut the dash to allow for the display without bezel Carefully follow the measurements of the included dash cut out to ensure enough of the dash is available to properly secure the display Torque the 6 32 Nylock nuts to 5 inch pounds 2 Place the display behind dash and line up the four mounting holes on the display with the holes in dash 3 Install four bolts and tighten nuts Page 8 of 28 500156 usermanual scc2 en 2 0 doc IE NE STEYRMOTORS INNOVATION WITH LIGHTNESS USER MANUAL SCC 2 3 Basic Functions Function Keys Function Keys MENU Key ENTER Key Flat Screen Display A color screen displays gauges fault messages and menu options for setup and configuration Function Keys Via the function Key s the different menus and options can be selected MENU Key Pressing the MENU key at any time displays the list of menu options ENTER Key Pressing the ENTER key will select the option displayed much like the ENTER key ona keyboard Wrong Hardware After SCC2 is activated the hardware is checked If an error is detected the following error message is displayed Please contact STEYR MOTORS Wrong Hardware Please contact STEYR MOTORS for more information Page 9 of 28 500156 usermanual scc2 en 2 0 doc Mi WV WZ STEYRMOTORS d em INNOVATION TH LIGHTWHESS USER MANUAL SC
10. ds it Precautions Do not use sharp or hard things such as ball pens Warranty The STEYR CONTROL CENTER is classified as an electronic device and the Warranty Conditions apply as specified in the STEYR MOTORS Marine Warranty Conditions Software Updates ooftware status and version undergo continuous improvements within their product life Software up dates can be called up on demand with specified procedures as provided by Steyr Motors NOTE In order to consistently bring you the highest quality full featured products we reserve the right to change our specifications and designs at any time Before beginning Installation or operation of this product e Read and follow all installation and operation manuals e Read and follow this user manual e Please contact STEYR MOTORS Service Partner immediately if you have any questions Page 4 of 28 500156 usermanual scc2 en 2 O doc STEYRMOTORS YRMOTORS USER MANUAL SCC 2 2 2 Cleaning the display Take care when cleaning the display to avoid damaging it e Do NOT wipe the display screen with a dry cloth as this could scratch the screen coating e Do NOT use acid ammonia based or abrasive products Regularly clean your Display as follows 1 Switch off the power to the Display 2 Wipe the Display with a clean soft cloth To remove oily finger marks use a spray cleaning agent of the type used for cleaning spectacles Cleaning the case Take care when cleaning the case to avo
11. id damaging it e Do NOT apply too high pressure to the case especially near the display as this could damage the display e Clean the case with a clean soft cloth water and soap e For obstinate soiling you can carefully use a mild detergent rinsing afterward with plenty of water 2 3 Abbreviations In this document the following terms and abbreviations are used Engine Control Unit M Steyr Control Center Version 2 Controller Area Network Serial communication protocol Global Positioning System Greenwich Mean Time Page 5 of 28 500156 usermanual scc2 en 2 O doc E Fe RR hee STEYRMOTORS M b L n ANA ut zy i ae INNOVATION WITH LIGHTNESS eer USER MANUAL SCC 2 2 4 Hardware Installation The following instructions will guide you through installing the PowerView display Inspecting Package Contents Be sure to inspect the kit for all parts before beginning installation If any parts are missing or damaged please get in contact with the Company the product has been purchased The items included in the box are Display unit Faceplate and cover Four each screws flat washers and nylock nuts Installation and Operations manual User manual P No 500156 not illustrated HelmView Model HVS780 Operations Manual Ci E N J o z LI A EE er 940 AT an g HelmView e Model HVS780 jar UN TOE Pena ana ert iA Page 6 of 28 500156 usermanua
12. l scc2 en 2 O doc Gr STEYRMOTORS Q innovation wir cronTness WEY USER MANUAL SCC 2 Dash Mounted Installation Tools needed e Drill with 5 32 in size bit e Saw e Wrench or socket 6 32 Nylock nuts provided to studs Preparing the Dash e Determine the location of the PowerView in the dash e Use the Installation Template see illustration below as a guideline to cut a hole in the dash to the specified dimensions HATCHED AREA INDICATES CRITICAL AREA 7 apo 315 ee 7 99 ae EXTERIOR BEZEL OUTLINE 4 76 E AA VG AA Yd EG SS CUT DOTTED LINE FG i 729 7 me l p 7 5 138 me 130 51 7 7 4 X 4 315 8 869 7 99 225 27 e Drill holes where indicated on the template for the mounting screws NOTE When using the paper template from this manual be aware that the pdf file may not automatically print to scale Check the accuracy of the printed template by verifying the measurements labeled on the template are correct Page 7 of 28 500156 usermanual scc2 en 2 0 doc STEYRMUTORS Q YRMO TORS USER MANUAL SCC 2 Mounting the Unit 1 Place the back side of the display through the opening in the dash 2 Use the four screws to line up the unit with the drilled holes 3 Push the unit through the opening and screws through the drilled holes until the back of the case Is flush 4 Use the Nylock nuts provided to tighten unit to the dash Use the appropriate wren
13. m color transmissive TFT LCD Resolution WVGA 800 x 480 pixels 16 bit color Viewing Angle 65 horizontal 55 65 vertical Orientation Landscape Backlighting LED 1000 nit typical brightness 40 000 hr minimum Contrast Ratio 400 1 Refresh Rate 60 Hz Microprocessor Freescale M i MX357 32 bit 532 MHz ARM11 core QNX Real time Operating System Flash Memory 2 GB total 1 GB available for data logging RAM 128 Mbytes SRAM Operating Voltage 6 36 VDC reverse polarity protected Environmental Operating Temperature 40 C to 85 C Storage Temperature 40 C to 85 C Protection IP66 and 67 front and back Emissions SAE J1113 Immunity SAE J1113 Vibration Random vibration 7 86 Grms 5 2000 Hz 3 axis Page 26 of 28 500156 usermanual scc2 en 2 0 doc STEYRMOTORS YRMOTORS USER MANUAL SCC 2 CE Marking Quality Standard ISO 9001 Directive 2004 108 EC European Electromagnetic Compatibility European Harmonised standard EN 61000 4 3 RADIATED EMF IMMUNITY EN 61000 4 4 EFT IMMUNITY POWER and I O LINES EN 61000 4 5 SURGES POWER LINES EN 61000 4 6 RF IMMUNITY EN 61000 4 8 MAGNETIC FIELD IMMUNITY EN 60945 ESD EN 60945 CONDUCTED EMISSIONS HYBRID EN60945 CISPR 11 CLASS B RADIATED EMISSIONS Page 27 of 28 500156 usermanual scc2 en 2 0 doc STEYRMOTORS YRMOTORS USER MANUAL SCC 2 SERVICE NETWORK Authorised Service Partner amp Dealer Easy access to established Service Partner Network can
14. mask displays max 10 active Service Codes Level 1 Service Code Level L1 current If a Service Code is active the icon for Alarm menu will change from grey to yellow see above illustration For Service Code table refer to Operation Manual of engine If an error Level 1 L1 occurs after ignition OFF and ON again the fault is stored in ECU as Level 2 L2 Level 2 Service Codes are not displayed via SCC 2 Clear Service Codes Once button Clear Service Codes is selected the active Service Codes Level 1 can be deleted In case the Service Code s reappears the Service Code is still active and the root cause must be determined For further assistance contact earliest possible a STEYR MOTORS authorized Service Partner Contacts of STEYR MOTORS authorized Service Partners under www steyr motors com network 500156 usermanual scc2 en 2 0 doc um STEYRMOTORS TH LIGHTNESS Jj A USER MANUAL SCC 2 5 5 Diagram menu Below screen will appear once the function key for menu Diagram is pressed In this mask three engine parameters can be selected The parameter graph shows the actual value present on the engine Unit ID 1650076 2000RPM RPM 5 5 1Change displayed parameter Below screen will appear once the function key for menu Diagram is pressed a second time Graph 2 Graph 3 Select Graph 1 2 or 3 Select engine parameter out of the preset list Page 19 of 28 500156 usermanual sc
15. re update for SCC ee ee ee RR EE ee Re Ee ee ee ee ee ee ee 6 2 Software update to display VO BOX menu Page 3 of 28 USER MANUAL SCC 2 500156 usermanual scc2 en 2 O doc STEYRMOTORS YRMOTORS USER MANUAL SCC 2 2 General 2 1 Important safety and legal information Liability STEYR MOTORS can accept no liability for e Consequential damage due to use of the SCC e Possible errors in the manuals and the results thereof e Use that is inconsistent with the purpose of the product Safety Do not work on an electrical system if it is still connected to a current source Only allow changes in your electrical system to be carried out by qualified electricians Under no circumstances shall STEYR MOTORS or any of its subsidiaries or any of its external suppliers accept liability for any loss of data income incidental damage or consequential losses incurred as a result of the use of the product whosoever caused when used as a monitor for electronically controlled engines or other systems even if the information shown on the display are wrong Navigation The GPS coordinates are only aid to navigation Its accuracy can be affected by many factors including equipment failure or defects environmental conditions and improper handling or use It is the user s responsibility to exercise common prudence and navigational judgment Always check that your route to a waypoint is safe before traveling towar
16. stration is kept pressed above gt 1second The Day Night mode can be displayed only for the Home menu Page 22 of 28 500156 usermanual scc2 en 2 0 doc STEYRMOTORS EEN fi d DY ALIE tie INNOVATION WITH LIGHTNESS WES USER MANUAL SCC 2 6 Software update 6 1 Software update for SCC 1 The Update Software File is to download only for STEYR MOTORS Service Partner from STEYR MOTORS homepage http www steyr motors com download manuals spare parts option equipment 2 Copy Update File on a USB Stick 3 Connect USB Stick to USB Port on the SCC2 display See chapter 4 Connecting the display point c 4 Press and hold any button on the SCC2 and turn at the same time the Ignition OFF and ON until the below mask is shown 5 Press Enter Key button two times 6 Update is proceeded automatically see below photo 7 The Update is finished when the Home menu appears 8 The updated SCC2 Software Version is displayed bottom left Page 23 of 28 500156 usermanual scc2 en 2 0 doc INNOVATION WITH LIGHTNESS if lE NE USER MANUAL SCC 2 6 2 Software update to display VO Box menu Procedure to load configuration file on SCC 2 display menu VO Box NOTE SCC Config txt is configured and provided from STEYR MOTORS on customers request b 2 3 Page 24 of 28 Copy the file SCC_Config txt on a USB Stick Ensure SCC2 is shutdown turn ignition OFF via engine s instrument panel key swi
17. tch or push button Connect USB Stick to USB Port on the SCC2 display See chapter 4 Connecting the display point c Turn on the SCC2 turn ignition ON via engine s instrument panel key switch or push button Press the button MENU key as below illustrated Wait until the button LOAD CONFIG is green Shutdown SCC2 turn ignition OFF via engine s instrument panel key switch or push button Remove USB Stick from USB Port of SCC2 refer to point 3 Turn on the SCC2 turn ignition ON via engine s instrument panel key switch or push button Menu l O Box appears with agreed settings 500156 usermanual scc2 en 2 O doc P r man a STEYRMOTORS Lj Au d AMS f INNOVATION WITH LIGHTNESS WEE USER MANUAL SCC 2 7 Dimensions for Installation 9 7485 247 41 6 225 158 12 8 849 4X D189 225 27 480 THRU HOLES 1 191 30 26 2 756 70 00 5 138 130 51 8 32 X 25 DEEP BRASS INSERTS 4 PLACES 8 878 225 50 THREADED INSERTS Page 25 of 28 500156 usermanual scc2 en 2 0 doc USER MANUAL SCC 2 8 Technical Data 4x 8 189 in 8 869 in 225 27 mm d nn 1 191 in 30 26mm 70mm 130 50mm 2 758 in 5 138 in 8 32 x 25 deep brass inserts 4 places L 9 748 in 247 7 mm 1 959 in 0 620 in 15 n n 49 75mm 6 225 in 158 2mm 8 869 in 225 27mm 0 708 in 18mm l Technical Display 7 178m
Download Pdf Manuals
Related Search