Home

User`s Manual Speed Dome Camera

1. Choose the appropriate baud rate protocol by setting the DIP switch 2400 BPS 4800 BPS 2 Communication Protocol Setup 3 Baud Rate Setup Select the appropriate baud rate with DIP switch combination The factory default is 9600BPS Choose the termination resistor on off to notify the last camera Normal 2 Last Camera 4 RS 485 Termination Setup Pin 8 is use for on off of RS 485 termination Normally it must be off state Especially when you have trouble with long daisy chain style connection turn on this termination switch of the last camera Camera ID Setup ID number of camera is set using binary number The example is shown below Pin 1 2 3 4 5 6 7 8 ID Value 1 2 4 8 16 32 64 128 5 DIP Switch for Camera ID Setup If you want to control a certain camera you must match the camera ID with CAM ID setting of DVR or keyboard controller ID number of the camera is set using binary number The range o
2. Auto Calibration If the camera is exposed the high temperature over 50 for along time the camera can lose focus As a result you will get a blurry image In this case enter Preset key 165 to enable auto calibration If auto calibration is enabled the camera will be re focused once every 6 hours If you want to disable this function enter Preset key 165 Main Functions Preset Max 127 positions can be stored as preset positions The preset number can be assigned from 1 to 128 but 95 is reserved for starting OSD menu Refer page 28 ROOT MENU gt FUNCTION SETUP gt PRESET SETUP for more detailed information 1 Set Preset Method 1 Use keyboard controller Refer to keyboard controller manual Method 2 Use OSD menu 2 Run Preset Method 1 Use keyboard controller Preset key Number key 1 128 3 Delete Preset To delete pattern use OSD menu 2 Scan By using scan function you can make camera to move between 2 preset positions repeatedly Refer page 30 ROOT MENU gt FUNCTION SETUP gt SCAN SETUP for more detailed information 1 Set Scan To set scan use OSD menu 2 Run Scan Method 1 If there is scan key on the keyboard controller Scan key Scan number 1 8 Enter key Ex Run scan 2 Scan key 2 Enter key Method 2 If there is no scan key on the keyboard controller Preset key Scan number 1 8 140 Ex Run scan 2 Pr
3. Pate Anti vandal Speed Dome Camera User s Manual UMH Safety Information RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Warning Precaution This symbol indicates that dangerous voltage This exclamation point symbol is intended to alert the consisting a risk of electric shock is present within user to the presence of important operating and this unit maintenance servicing instructions in the literature accompanying the appliance WARNING To prevent damage which may result in fire or electric shock hazard do not expose this appliance to rain or moisture WARNING 1 Be sure to use only the standard adapter that is specified in the specification sheet Using any other adapter could cause fire electrical shock or damage to the product 2 Incorrectly connecting the power supply or replacing battery may cause explosion fire electric shock or damage to the product 3 Do not connect multiple cameras to a single adapter Exceeding the capacity may cause abnormal heat generation or fire 4 Securely plug the power cord into the power receptacle Insecure connection may cause fire 5 When installing the camera fasten it securely and firmly A falling camera may cause personal injury 6 Do not place conductive objects e g screw drivers coins metal t
4. Bottom of Main Body Mounting Hole 34 Pipe Mounting Hole Surface Mount Bracket Dome Cover Protects the camera module from outside environment Do not detach protection vinyl from the dome cover before finishing all installation processes to protect dome cover from scratches or dust Lockup Screw Fixes main body to the surface mount bracket 7P Terminal Block Slot Power keyboard controller DVR video device are connected to this terminal block Refer page 17 for details DIP Switch Adjusts camera ID and protocols Refer page 8 9 for details 5P Terminal Block Slot Alarm input and relay out cables are connected to this terminal block Refer page 16 for details Mounting Hole This is used to attach the surface mount bracket to the ceiling 22 Pipe Mounting Hole This is used to pass the cables to the cameras When water protection is needed connect the 34 pipe through this hole then pass the cables through the pipe DIP Switch Setup Before installing the camera you should set the DIP switch to configure the camera ID communication protocol Pin On Off If the pin is located ON side of the printed label it means on In reverse means Off i ON Pin On ON i H 1c 1 Pin Off 1 L J 1 DIP Switch for Communication It is consist of Communication protocol baud rate and RS 485 termination setup pins If you change the c
5. 440K pixels 752 H x 582 V
6. The rated power is marked on the bottom of the camera Power Range Power Consumption Monitor DC 12V DC 11V 15V 8W Connects to video output device such as monitor using the BNC coaxial cable Fan Heater model consumes 12W 17 Check Points before Operation 1 Before power is applied please check the cables carefully Check Points before Operation 2 The camera ID of the controller must be identical to that of the target camera The camera ID can be checked by reading DIP switch of the camera 3 If your controller supports multi protocols the protocol must be changed to match to that of the camera 4 If you changed camera protocol by changing DIP switch the change will be effective after you reboot the camera 5 Since the operation method can be different for each controller available refer to the manual for your controller if camera cannot be controlled properly Preset and Pattern Function Pre check Check how to operate preset and pattern function with keyboard controller DVR in advance to operate camera function fully when using keyboard controller DVR If keyboard controller DVR has no pattern key or function use shortcut keys with preset numbers For more information refer to Reserved Preset below Reserved Preset Some preset numbers are reserved to special functions Preset key 95 Enters into OSD menu Preset key 131 134 Runs pattern function 1 4 Preset key 141 148 Run
7. lt MANUAL gt AGC NORMAL SSNR MIDDLE SENS UP lt AUTO gt BACK EXIT IRIS AUTO MANUAL If iris is set to AUTO iris should have highest priority in adjusting AE and shutter speed should be fixed If iris is set to MANUAL iris should be fixed and iris has lower priority in adjusting AE in comparison with others SHUTTER ESC A FLICKER MANUAL If iris is set to MANUAL and shutter speed is set to ESC shutter speed should have highest priority Shutter speed is set to A FLICKER to remove flicker shutter speed should be set to 1 100 sec for NTSC and 1 120 for PAL AGC OFF NORMAL HIGH Enhances the image brightness automatically in case that luminance level of image signal is too low MANUAL IRIS IRIS LEVEL 0 SSNR OFF LOW MIDDLE HIGH Enhances the images by deducting noises when gain level of images is too high SENS UP AUTO OFF Activates the slow shutter function when luminance of image signal is too dark It is possible to set up the maximum number of frames piled up one on another by Slow Shutter function MANUAL SHUTTER SHUTTERSPD x2 EXIT AUTO SENS UP SENS UP LIMIT x2 EXIT MANUAL IRIS SCREEN IRIS LEVEL O 100 MANUAL SHUTTER SCREEN SHUTTER SPD x128 1 120000 AUTO SENS UP SCREEN SENS UP LIMIT x2 x128 37 OSD SYSTEM SETUP 38 SYSTEM SETUP Press
8. 1 4 SCAN 1 4 Select the function Select the function no separately Press Near Enter DWELL TIME 00 03 04 00 min sec Key Sets dwell time between function by moving joystick Up Down If the O A gt OPT of pattern group is set to repeat more than twice it means the repeat EDIT GROUP 1 interval NO ACTION NO DWELL OPT OPT PRESET 2 360 PATTERN amp SCAN 1 255 1 NONE It should be preset speed when preset is set in ACTION It should be the 2 NONE number of repeat when pattern or scan is selected in ACTION 3 NONE 4 NONE 5 NONE SAVE LNEAR EDIT ACT EDIT GROUP Select Function Sequence CANCEL FAR EDIT END l C P Note that max 20 functions are allowed in a group i Move cursor Up Down to rotate among 20 functions ress Near Enter K id EDIT GROUP Assign Function 5 m R Move cursor to the NO to assign the function press near key to EDIT GROUP 1 set up Select the function by moving joystick Up Down 32 EDIT GROUP 1 gt 4 Press Near Enter Key PATTERN1 00 03 1 NONE NONE NONE NONE 1 PATTERN1 00 03 1 2 NONE 3 NONE 4 NONE 5 NONE OSD FUNCTION SETUP gt GROUP SETUP EDIT GROUP Assign Function Move cursor Left Right to select items and move cursor Up Down to change each value EDIT GROUP Select Function Sequence Ea The function undefined cannot be set as action e g If PATTE
9. EXIT L 4 Press Near Enter Key g gt PATTERN SETUP PATTERN NO 1 DEFINED CLR PATTERN CANCEL lt EDIT PATTERN BACK EXIT lt A Select lt EDIT PATTERN gt Press Near Enter Key a N EDIT PATTERN 1 MOVE TO START POSITION NEAR START FAR CANCEL 0 0 x1 E Move Camera to Area Press Near Enter Key g N 1 BERRRRRRRREE LNEAR SAVE FAR DELETE 0 0 x1 E a 4 Record the Path of the Pattern by Camera Control NEAR SAVE FAR DELETE 0 0 x1 E S PATTERN SETUP It records the free path of camera by joystic control PATTERN NO 1 4 Select pattern number to edit If a selected pattern number is not defined UNDEFINED will be displayed under selected pattern number CLR PATTERN CANCEL OK Deletes data in the current pattern lt EDIT PATTERN gt Moves to edit the pattern assigned EDIT PATTERN Select the Position 1 By using joystick move to start position 2 By using joystick move to the appropriate zoom 3 To start pattern recording press near key EDIT PATTERN Records the Path 1 Move camera with joystick of controller or run preset function to memorize the path mostly curve path in a selected pattern 2 The total memory size and the rest memory size is displayed in the form of bar Refer screen 5 If bar is full as below the camera does not record any more paths B The pattern path includes the zoom magnification
10. Near Enter Key a DATE TIME SETUP DATE O1 JAN 2008 T UE TIME 00 00 01 H M S RELAY TYPE SETUP RELAY1 NORMAL OPEN ia EDIT PASSWORD a M234567890 OK ABCDEFGHIJ CANCEL KLMNOPQRST UVWXYZabcd DNAs EE ae opqrstuvwx br ee Nae 5 amp S SYSTEM SETUP lt DATE TIME SETUP gt Moves to DATE TIME SETUP screen Refer screen 2 below lt RELAY TYPE gt Moves to RELAY TYPE setup screen Refer screen 3 below lt PASSWORD gt Moves to PASSWORD setup screen Refer screen 4 below lt SET HOME POSITION gt Moves to SET HOME POSITION screen Refer screen 5 on page 39 lt SET NORTH DIRECTION gt Moves to SET NORTH DIRECTION screen Refer screen 6 on page 39 LANGUAGE ENGLISH ESPANOL FRANCAIS DEUTSCH ITALIANO PYCCKUN PORTUGUES Select a preferred language among English Spanish French German Italian Russian and Portuguese lt FAN HEATER SETUP gt Moves to FAN HEATER SETUP screen Refer screen 7 on page 39 This setup is only applicable for fan heater model DATE TIME SETUP DATE 01 JAN 2000 31 DEC 2037 Date is displayed in dd mm yy format 1 If you press the near key the focus will be placed on dd 2 Sets date moving joystick Up Down 3 Moves joystick Left Right to move to date month year 4 The values in the field are changed using Up Down keys Eg The day is automatically calcul
11. ON OFF CLEAR MASK CANCEL OK lt EDIT MASK gt Select the Camera location Select the Mask Size amp Color TEMPERATURE CELSIUS FAHRENHEIT OFF lt MOTION SETUP gt PRESET LOCK ON OFF PWR UP ACTION ON OFF AUTO FLIP ON OFF JOG MAX SPEED 2 SEC 360 SEC Default 140 SEC JOG DIRECTION INVERSE NORMAL FRZ IN PRESET ON OFF lt PARKING ACTION SETUP gt PARK ENABLE ON OFF WAIT TIME 00 00 05 04 00 00 PARK ACTION HOME PRESET SCAN PATTERN GROUP lt ALARM INPUT SETUP gt ALARM TYPE N O Normal Open N C Normal Close ALARM ACTION NOT USED HOME PRESET 1 128 SCAN 1 8 PATTERN 1 4 GROUP 1 4 lt FUNCTION SETUP gt lt PRESET SETUP gt PRESET NO 1 UNDEFINED 128 UNDEFINED lt EDIT SCENE gt Select the Camera location lt LABEL gt Input Label CLR PRESET CANCEL OK CAM ADJUST GENERAL SPECIAL ALARM OUT 1 lt SCAN SETUP gt SCAN NO 1 UNDEFINED 8 UNDEFINED 1ST POSITION PRESET 1 128 2ND POSITION PRESET 1 128 SCAN SPEED 2 SEC 360 SEC Default 30 SEC CLEAR SCAN CANCEL OK lt PATTERN SETUP gt PATTERN NO 1 UNDEFINED 4 UNDEFINED CLR PATTERN CANCEL OK lt EDIT PATTERN gt Select the Camera location lt GROUP SETUP gt GROUP NO 1 UNDEFINED 8 UNDEFINED CLEAR GROUP CANCEL OK lt EDIT GROUP gt Select the camera action operation time and option 1 NONE 20 NONE lt SCHEDULE SETUP gt MASTER ENABLE ON OFF Schedule No 1 UNDEFINED 7 UNDEFINED 22 LANGUAGE ENGLI
12. SCENE gt lt LABEL gt CLRPRESET CANCEL CAM ADJUST lt SPECIAL gt ALARM OUT BACK EXIT XX Press Near Enter Key g CAM ADJUST PRESET1 lt WHITE BALANCE SETUP gt lt AUTO EXPOSURE SETUP gt BACK EXIT a CAM ADJUST Sets WB AE for the preset when CAM ADJUST value is SPECIAL lt WHITE BALANCE SETUP gt Moves to WHITE BALANCE SETUP screen Refer page 36 lt AUTO EXPOSURE SETUP gt Moves to AUTO EXPOSURE SETUP screen Refer page 37 29 30 SNNT FUNCTION SETUP lt PRESET SETUP gt lt SCAN SETUP gt lt PATTERN SETUP gt lt GROUP SETUP gt lt SCHEDULE SETUP gt BACK EXIT S A Press Near Enter Key a N SCAN SETUP SCAN NO 1 1ST POS NOT USED 2ST POS NOT USED SCAN SPEED 30 SEC CLEAR SCAN CANCEL BACK EXIT N y OSD FUNCTION SETUP gt SCAN SETUP SCAN SETUP Up to 8 scans are available which makes the camera to move slowly between two preset positions When scan function runs the camera moves from the preset assigned as the 1st pos to the preset assigned as the 2nd pos in CW Clockwise direction Then camera moves from the preset assigned as the 2nd pos to the preset assigned as the 1st pos in CCW Counterclockwise direction Then it continues to move from the 1st pos to the 2nd pos back and forth If the 1st POS the2nd POS In case that the preset assigned as the 1st pos is same as the preset assigned as t
13. Sets maximum jog speed Jog speed is inversely proportional to zoom magnification As zoom magnification goes up pan tilt speed goes down JOG DIRECTION INVERSE NORMAL If you set this to INVERSE the view in the screen is moving same direction with jog tilting If NORMAL is selected the view in the screen is moving reversely FRZ IN PRESET ON OFF At start point of preset movement camera starts freezing the image of start point Camera keeps displaying the image of start point during preset movement and does not display the images which camera gets during preset movement As soon as camera stops at preset end point camera Starts displaying live images which it gets at preset end point This function availability should be different by models lt PARKING ACTION SETUP gt Moves to PARKING ACTION SETUP screen lt ALARM INPUT SETUP gt Moves to ALARM INPUT ACTION screen PARKING ACTION SETUP If PARK ENABLE is set to ON camera runs assigned function automatically if there is no PTZ command during assigned WAIT TIME PARK ENABLE ON OFF Enables Disables PARKING ACTION WAIT TIME 00 00 05 04 00 00 The time is displayed with hh mm ss format and you can change this by 1 sec unit 1 To place the cursor on the time marked as below press near key 0 10 00 2 Move joystick Left Right to adjust hours minutes and seconds 3 Move joystick Up Down t
14. Speed x128 1 120000 sec Anti Flickerless AGC Normal High Off White Balance Auto Manual Red amp Blue Gain Adjustable BLC Low Middle High Off Flickerless Selectable SSNR Low Middle High Off Other Functions Frame Freeze Function System Image Flip by Installation Type Pan 360 Endless Range Tilt 0 180 Auto Flip On 0 90 Auto Flip Off Preset 360 sec Pan Tilt Speed Manual 0 05 360 sec Zoom Proportional Scan 1 180 sec Pan Tilt Preset 127 Presets with Labels Independent Camera Setup Pattern 4 Patterns Approx 5 Minutes for Each Pattern Scan 8 Scans Group 8 Groups Max 20 Enters for Each Group Schedule 7 Rules Condition Day Time Action Preset Scan Group Pattern Other Functions Image Auto Flip Auto Parking Power up Action amp etc Communication RS 485 Protocol Auto Pelco D Pelco P Samsung Panasonic GE Kalatel AD American Dynamics Selectable Privacy Zone 4 Zones Sensor In Out Built in 2 Input 1 Relay Output oT Temperature Day and Date amp Time Display Support 7 Languages ENGLISH ESPANOL FRAN AIS DEUTSCH ITALIANO PYCCKUN PORTUGUES General ae DC 12V 7 8W Fan amp Heater Model Consumes 12W we Dual Voltage Model AC 24V DC 12V 7 8W Dome 115 mm Demension Housing 165 x 101 5 H mm Weight Approx 2 4 Kg 5 3Lbs Operating Temp 10 C 50 C 14 F 122 F 44 470K pixels 795 H x 596 V
15. display on main screen lt PRIVACY ZONE gt it is changed tea Re OFF ACTION TITLE ON OFF AUTO EXIT lt MOTION SETUP gt EXIT PRESET LABEL ON OFF AUTO a Setup for motion related settings D ALARM I O ON OFF AUTO lt FUNCTION SETUP gt hi R DATE TIME ON OEE Setup for various functions such as preset scan pattern group and schedule Key lt PRIVACY ZONE gt EE d Moves to the privacy zone setup lt gt Configure camera related functions and data PRIVACY ZONE TEMPERA TUBE CELSIUS FANRENBEN Or MASKNO Io lt SYSTEM SETUP gt UNDEFINED PRIVACY ZONE Configure for basic system setup DISPLAY OFF 3 CLEAR MASK CANCEL Selects area in image to mask lt SYSTEM INITIALIZE gt lt EDIT MASK gt It selects the area to mask and setup various function of the mask Initializes system configuration and sets all data to factory default configuration BACK MASK NO 1 4 EXIT FXIT Select mask number If the selected mask has data already camera moves To escape from the OSD setting go to exit lt J as it was set Otherwise UNDEFINED will be displayed under MASK NO Select lt EDIT MASK gt DISPLAY ON OFF l Press Near Enter Key Sets if the camera makes mask shows or not on images aa N CLEAR MASK CANCEL OK EDIT MASK 1 Deletes data in the selected mask no ES aad lt EDIT MASK gt Moves to setup the mask no ETRE REE DOCTOR EDIT MASK Select Mask Location 5 1 Move camera to area to mask o SYSTEM
16. of the mask must be 20 bigger than the original target size so as to mask the objects during high speed pan tilt k 24 25 26 OSD MOTION SETUP MOTION SETUP PRESET LOCK OFF PWR UP ACTION ON AUTO FLIP ON JOG MAX SPEED 140 SEC JOG DIRECTION NORMAL FRZ IN PRESET OFF lt PARKING ACTION SETUP gt lt ALARM INPUT SETUP gt B 4 Press Near Enter Key PARKING ACTOIN SETUP PARK ENABLE Q WAIT TIME 0 PARK ACTION HOME BACK EXIT MOTION SETUP Setup the general functions of pan tilt motions PRESET LOCK ON OFF If motion lock is set to on it is impossible to set up and delete preset scan pattern and group It is possible only to run those functions To set up and delete those functions enter into OSD menu PWR UP ACTION ON OFF This function enables to resume the last action executed before power down Most of actions such as preset pattern scan and group are available for this function but jog actions are not available to resume AUTO FLIP ON OFF In case that tilt angle arrives at the top of tilt orbit 90 zoom module camera keep moving to opposite tilt direction 180 to keep tracing targets As soon as zoom module camera passes through the top of tilt direction 90 images should be reversed automatically and F appears in screen If this function is set to OFF tilt movement range is 0 90 JOG MAX SPEED 2 SEC 360 SEC
17. the Wall Mount Bracket Drill the wall to Fix the Anchor Bolts Fix the Junction Box O Close the Junction Box Cover Fix the Sun Shield Bracket G Wire Cables Connect the Terminal Blocks Fix the Main Body Detach the Protection Vinyl Owire Cables Wire the cables to the terminal block Refer page 16 17 Connect the Terminal Blocks Connect terminal blocks to the main body Refer page 10 Fix the Main Body Screw the main body to the surface mount bracket Screws are included in the main body Detach the Protection Vinyl Detach the protection vinyl from the dome cover 15 Cabling the 5P Terminal Block Relay Out 5P Terminal Block 5p terminal block connects the sensor alarm input and the relay out device to the camer s main body Refer Installation Using Surface Mount Bracket of page 10 for the connection of the terminal block 2 Sensor Alarm Input Sensor Alarm Input It connects to IR sensor IrDA sensor or door switch If the sensor is activated it can activate to move camera to the specific angle and to connect the alarm device Sensor Alarm Input Slot Relay Out Input Slot A cable of the sensor should connect to input 1 or 2 and Relay Out the other should be connected to COM slot It connects to the alarm lights siren or lamps and it is If you want to use alarm input the types of sensor must be activated according Ton
18. 3 To save data and exit press near key 4 To cancel recording and delete the recorded data press far key When pattern is edited or ok pan tilt will turn to AUTO FLIP gt OFF temporarily 31 OSD FUNCTION SETUP gt GROUP SETUP O GROUP SETUP SCREEN FUNCTION SETUP a a a The group function allows running sequence of presets pattern SERESELS o and or scans Max 8 group can be stored Each group can have lt PATTERN SETUP gt i iti i lt CROUP SETUPS max 20 action entities which can be preset pattern or scan lt SCHEDULE SETUP gt Dwell Time BA K i J Peet eens L pattems he Press oo Max 20 Entities 2 Q GROUP SETUP GROUP NO Tef GROUP NO UN DEFIN ED Selects group number to edit If a selected group number is not defined CLEAR GRO up CANCEL UNDEFINED will be displayed under the selected group number lt 7 CLEAR GROUP CANCEL OK Deletes data in the current group BACK lt EDIT GROUP gt EXIT Moves to edit the group assigned N a EDIT GROUP Initial Screen To edit group press near key to move screen 4 At the current screen if moves joystick Down the cursor will move EDIT GROUP 1 to SAVE menu NO ACTION NO DWELL OPT l UT NONE NO 20 Means the sequence of the function in a group The functions will be run from lower no to higher no by sequence ACTION NO NONE PRESET 1 128 Excluding 95 PATTERN
19. Contents ROOT MENU The 1st screen The 2nd screen Value lt CAMERA SETUP gt FOCUS MODE AUTO MANUAL SEMIAUTO DIGITAL ZOOM ON OFF IMAGE FLIP ON OFF lt WHITE BALANCE SETUP gt WB MODE AUTO MANUAL RED ADJUST 10 60 BLUE ADJUST 10 60 lt EXPOSURE SETUP gt BACK LIGHT OFF LOW MIDDLE HIGH DAY NIGHT AUTO1 AUTO2 DAY NIGHT BRIGHTNESS 0 100 Default 25 IRIS AUTO MANUAL 0 100 SHUTTER ESC A FLICKER MANUAL x128 1 120000 sec AGC OFF NORMAL HIGH SSNR OFF LOW MIDDLE HIGH SENS UP AUTO 2 128 OFF lt SYSTEM SETUP gt lt DATE TIME SETUP gt DATE dd mm yyyy TIME hh mm ss lt RELAY TYPE gt RELAY 1 N O Normal Open N C Normal Close lt PASSWORD gt Input Password lt SET HOME POSITION gt Select the Camera location lt SET NORTH DIRECTION gt Select the Camera location ROOT MENU The 1st screen The 2nd screen The 3rd screen The 4th screen Value lt SYSTEM INFORMATION gt FIRMWARE VER 1 0 COLOR SYSTEM NTSC PROTOCOL PELCO D BAUD RATE 2400 ADDRESS 1 lt DISPLAY SETUP gt CAMERA ID ON OFF PTZ INFORMATION ON OFF AUTO ACTION TITLE ON OFF AUTO PRESET LABEL ON OFF AUTO ALARM I O ON OFF AUTO DATE TIME ON OFF lt PRIVACY ZONE gt MASK NO 1 UNDEFINED 4 UNDEFINED DISPLAY
20. F Initializes motion configuration CLR FUNCTION SET ON OFF Deletes preset data scan data pattern data group data and schedule data REBOOT CAMERA ON OFF Reboots zoom camera module REBOOT SYSTEM ON OFF Reboots speed dome camera OSD menu contents on page 22 23 default values of each content are marked in bold 40 157 5 64 N 1 34 NPT Q 83 5 41 4 Dimensions of Option Brackets Dimensions of Option Brackets 1 Flush Mount Ring Bracket Unit mm 2 Sun Shield Mount Bracket Unit mm 3 Wall Mount Bracket Unit mm 2 Ceiling Mount Bracket Unit mm 374 6 B 276 2 Ja 188 7 57 5 i 7 B141 5 355 5 71 6 1 F 164 6 Specifications Image Device 1 4 Interline Transfer CCD Total Pixel 410K pixels 811 H x 508 V Effective Pixel 380K pixels 768 H x 494 V H Resolution Color 500 TV Lines B W 570 TV Lines S N Ratio 50dB AGC Off Zoom x10 Optical Zoom amp x10 Digital Zoom Focal Length F 1 8 f 3 8 38mm Min IIluminance Color 0 7 Lux 50 IRE B W 0 02 Lux Camera Day amp Night Auto Day Night IR Cut Filter Focus Auto Manual Semi Auto Iris Auto Manual Shutter
21. INFORMATION E EEEE EERE eae 4 se ete oe 2 Adjust the mask size Use the zoom key to adjust the image size SYSTEM INFORMATION Shows basic information and current configuration of the system lt Tay E 3 Press near key to complete the location COLOR SYSTEM NTSC FIRMWARE VER Move Camera to Area to Mask E ProD Shows the current firmware version Pies Neal Enter Rey 0 EDIT MASK Select Mask Color and Size ADDESS COLOR SYSTEM O N 1 Choose the mask color using zoom key Shows the current analog video system EDIT MASK 1 The current color is 50 transparent When the mask setting aeck pRoroco S ooo oo is completed the mask area is masked by 100 opaque color L Shows the current PTZ control protocol 2 Move joystick Left Right to adjust the width 3 Move joystick Up Down to adjust the height BAUD RATE Shows the current baud rate of the PTZ control ZOOM COLOR CHANGE ates nee key My complete the seng gt ADJ UST MASK eee 5 If press far key it returns to the previous setting without ADDRESS storing the setting Shows the current camera ID of the PTZ control C NEAR SELECT FAR CANCEL 3 ve mg MASK SETTING Completion Screen Press Near Key to Save Run the mask no marked on the screen The value of DISPLAY is set to ON automatically O A ERINA ZONE N Can set mask 2 4 continuously The objects behind the mask can be shown when the camera is moving in a short period It is recommended that the size
22. MODE MANUAL RED ADJUST 117 BLUE ADJUST 40 BACK EXIT h 4 lt WHITE BALANCE SETUP gt Move to WHITE BALACE SETUP screen lt AUTO EXPOSURE SETUP gt Move to AUTO EXPOSURE SETUP screen WB SETUP WB MODE AUTO MANUAL Red and blue level can be set up manually only in manual mode RED ADJUST 10 60 Adjust the red color value It can be set only in manual mode BLUE ADJUST 10 60 Adjust the blue color value It can be set only in manual mode WB SETUP Set WB Mode to Manual If WB mode changes to MANUAL the value of RED ADJUST and BLUE ADJUST shows on the screen GO WB SETUP Change WB Color Value If WB mode changes to MANUAL the color value of RED ADJUST and BLUE ADJUST can be set up manually To save data and exit press near key OSD CAMERA SETUP gt AE SETUP AE SETUP Setup the video related function of zoom camera module BACKLIGHT OFF LOW MIDDLE HIGH Sets the backlight compensation DAY NIGHT AUTO1 AUTO2 DAY NIGHT AUTO1 exchanges day night mode faster than AUTO2 BRIHGTNESS 0 100 Adjusts the brightness of images CAMERA SETUP FOCUS MODE SEMIAUTO DIGITAL ZOOM ON IMAGE FLIP OFF lt WHITE BALANCE SETUP gt lt AUTO EXPOSURE SETUP gt BACK EXIT A Press Near Enter Key O AE SETUP BACKLIGHT OFF DAY NIGHT AUTOL BRIGHTNESS 25 IRIS lt MANUAL gt SHUTTER
23. O Temperature Current temperature Boxed C and F means celsius and fahrenheit respectively Refer page 25 for setting temperature unit ROOM MENU gt DISPLAY SETUP gt TEMPERATURE 20 Tilt Angle in Degree 12 Pan Angle in Degree Alarm Input Information This information shows current state of alarm Input If an input is on state it will show the number of input If an input is off state will be displayed ji Alarm 1 Slot of the Terminal Block Alarm 2 Slot of the Terminal Block Relay Out Information This information shows the current state of relay out If the output is on state it will show the number of output If an output is off state will be displayed Relay Out On Relay Out Off 0 1 0 Compass Direction Shows the current compass direction of the camera The direction is shown as N North S South E East W West NE Northeast NW Northwest SE Southeast SW Southwest Refer page 39 for setting compass direction ROOT MENU gt SYSTEM SETUP gt SET NORTH DIRECTION Zoom Magnification Shows the current zoom magnification Tilt Angle in Degree Shows the current tilt O 180 angle Pan Angle in Degree Shows the current fan 0 359 angle Moveto the Previous Screen Joystick Up a N ROOT MENU Joystick __ Up Down to k 4 Press Press Far Key Near Enter Key N DISPLAY SETUP an CE eee eee eee
24. RN 1 is not defined at ROOT MENU gt FUNCTION SETUP gt PATTERN SETUP then the ACTION 1 will be automatically changed to NONE EDIT GROUP 1 9 MAME lt ln case that PATTERN 1 is not defined gt EDIT GROUP Saves the Setting After finishing setting up all actions place cursor on SAVE Then press near key to save data 33 34 SNNT FUNCTION SETUP Press Near Enter 5 242222222 JJJJJJJ DEECcEECECEJ A Joystick Down Press Near Key SCHEDULE SETUP MASTER ENABLE 1 TN Q O OO ZT JJJJJ mmmmm N N N N N lt TN OuBoon QeCceee gt Joystick Down i N SCHEDULE SETUP orn Dae ID Oon z4 ooo 12n EL INOA UON e JJJJJJ gt ecccccc AZZZ2Z222 a k Assign Value A N SCHEDULE SETUP m N MMMM THT TIT T1T1 SS St I gt OSD FUNCTION SETUP gt SCHEDULE SETUP 2 SCHEDULE SETUP SCREEN The schedule function allows running the appropriate function like preset scan group pattern home move at designated day and time e g if you setup a rule Tuesday at 9 00AM and Preset 1 say main gate the camera will move to main gate every Tuesday at 9 00AM It is noted that due to the real time clock ROOT MENU gt SYSTEM SETUP gt DATE TIME SETUP the time data will be kept regardless of blackout The initial time and day setup is
25. SH ESPANOL FRAN AIS DEUTSCH ITALIANO PYCCKUII PORTUGUES lt FAN HEATER SETUP gt FAN RUN TIME 30 C 80 C 86 F 176 F Default 40 C HEATER RUN TIME 10 C 20 C 14 F 68 F Default 5 C lt SYSTEM INITIALIZE gt CLEAR ALL DATA NO YES CLR DISPLAY SET NO YES CLR CAMERA SET NO YES CLR MOTION SET NO YES CLR FUNCTION SET NO YES REBOOT CAMERA NO YES REBOOT SYSTEM NO YES The bold characters of the value are the default value of the system Refer page 40 SYSTEM INITIALIZE The menu of ROOT MENU gt SYSTEM SETUP gt FAN HEATER SETUP is applicable only for fan heater model 23 OSD ROOT MENU amp SYSTEM INFORMATION OSD DISPLAY SETUP O PEER ROOT MENU O E DISPLAY SETUP R o a ayainie To enter this screen enter Preset key 95 O O res This menu defines to enable disable of OSD display on main screen lt SYSTEM INFORMATION gt CAMERA ID ON lt DISPLAY SETUP gt PTZ INFORMATION ON CAMERA ID ON OFF lt MOTION SETUP E ction aca eaeoiourentan ACTION TITLE ON lt FUNCTION SETUP gt ows Information ana current configuration PRESET LABEL ON PTZ INFORMATION ON OFF AUTO re Ee PEE EnG RM V0 oN If an item is set to be AUTO the item is displayed only when the value of lt SYSTEM INITIALIZE gt Enable Disable of OSD
26. amera protocol by changing the DIP switch the change will be effective after rebooting the camera Bottom of Main Body DIP Switch for Communication DIP Switch for Camera ID Setup RS 485 Termination Baud Rate Setup Pin Setup Pin Communication Protocol Setup Pin 2 Communication Protocol Setup If you want to control using DVR or keyboard controller their protocol must be identical to the camera s protocol Otherwise you cannot control the camera The factory default is auto protocol Auto Protocol If you set the protocol as auto protocol camera will automatically recognize the kind of protocol Choose the appropriate communication protocol by setting the DIP switch PELCO D Auto Protocol If there is other combination of pins from above it will be recognize as auto protocol DIP Switch Setup Q AD American Dynamics
27. ass the cables 2 On the fixed anchor bolts attach the rubber gasket and fix the wall mount bracket with nuts and screws 2 Installing on the Wooden Wall Drill the Wall To pass cables to the wall make a hole about 30 mm on the wall Fix the Wall Mount Bracket Pass the cables into the wall mount bracket and screw the wall mount bracket to the wall Fix the Surface Mount Bracket Pass the cables through the hole of the surface mount bracket screw the surface mount bracket to the wall mount bracket wire Cables Wire the cables to the terminal block Refer page 16 17 Connect the Terminal Blocks Connect terminal block to the main body Refer page 10 Fix the Main Body Screw the main body to the surface mount bracket Screw are included in the main body Detach the Protection Vinyl Detach the protection vinyl from the dome cover 13 Drill the Wall to Fix the Anchor Bolts On the wall drill a hole 6mm diameter 50mm depth for fix the anchor bolts Pass Cables through the Wall Mount Bracket Pass cables before fixing the wall mount bracket Fix the Junction Box Fix the junction box to anchor bolts on the wall Close Junction Box Cover Close cover to the junction box using the torx driver Fix the Sun Shield Bracket Fix the sun shield bracket to the wall mount bracket 14 Installation Using Wall Mount Bracket with Junction Box Option Pass Cables through
28. ated when you set the day TIME Time is displayed in HH MM SS format Sets time same as setting date RELAY TYPE SETUP RELAY1 NORMAL OPEN N O NORMAL CLOSE N C Contacts type of relay out are defined Refer page 14 for the detailed information EDIT PASSWORD Sets the 4 characters long password If this function is set to ENABLE the password is required whenever you enter OSD menu The master password is 4321 B To input password refer LABEL on page 29 5 OSD SYSTEM SETUP SET HOME POSOTION MOVE TO TARGET POSITION LNEAR SELECT FAR CANCEL 0 0 x1 E 4 i SET NORTH DIRECTION MOVE TO TARGET POSITION LNEAR SELECT FAR CANCEL 0 0 x1 N 4 7 FAN HEATER SETUP FAN RUN TEMP 40 HEATER RUNTEMP 50C C SET HOME POSITION Home position means the origin of pan angle calculation The value of pan angle displayed on the screen is based on this home position By using joystick move the camera to the desired position and press near key Home is not effective to tilt angle If you change the location of the home position all horizontal location of functions such as preset scan pattern group and privacy zone mask will be shifted based on the changed home position Set Home Position When you replace the camera block or the orientation of camera is changed due to maintenance operations it is very difficult to mainta
29. e Avoid installing in humid or dusty places e Avoid installing in places where radiation is present e Avoid installing in places where there are strong magnetic fields and electric signals e Avoid installing in places where the camera would be subject to strong vibrations e Never expose the camera to rain and water Contents 1 Introduction 2 Installation 3 OSD Menu 4 Specification 4 Precation 6 Product amp Accessories 7 Parts Name amp Functions 8 10 11 12 13 14 16 17 18 19 20 21 22 24 25 26 28 30 31 32 34 36 37 38 40 42 44 DIP Switch Setup Installation Using Surface Mount Bracket Installation Using Flush Mount Ring Bracket Option Installation Using Ceiling Mount Bracket Option Installation Using Wall Mount Bracket Option Installation Using Wall Mount Bracket with Junction Box Option Cabling the 5P Terminal Block Cabling the 7P Terminal Block Check Points before Operation Main Functions OSD Information General Rules of Menu Operation OSD Menu Contents OSD ROOT MENU amp SYSTEM INFORMATION OSD DISPLAY SETUP OSD MOTION SETUP OSD FUNCTION SETUP gt PRESET SETUP OSD FUNCTION SETUP gt SCAN SETUP OSD FUNCTION SETUP gt PATTERN SETUP OSD FUNCTION SETUP gt GROUP SETUP OSD FUNCTION SETUP gt SCHEDULE SETUP OSD CAMRA SETUP gt WB SETUP OSD CAMRA SETUP gt AE SETUP OSD SYSTEM SETUP OSD SYSTEM INITIALIZE Dimensions Dimensions of Opt
30. e OSU menu setting selected in OSD menu ROOT MENU gt MOTION SETUP gt If you want to use relay out the types of sensor must be ALARM INPUT SETUP The sensor types are normal open selected in OSD menu ROOT MENU gt SYSTEM SETUP gt and normal close RELAY TYPE The sensor types are normal open and Normal Open Output voltage is high state when sensor is normal close N O activated Normal Open Output voltage is high state when sensor is N O activated Normal Close Output voltage is high state when sensor is not N C activated Normal Close Output voltage is high state when sensor is not N C activated In 25 cM Activation In 2 sp In 2 0om Activation In 2 lt c lt Inside of terminal block Activation type of alarm input N O N C gt lt Inside of terminal block Activation type of relay out N O gt 16 Cabling the 7P Terminal Block Monitor Keyboard Controller DVR Keyboard Controller DVR 7P Terminal Block O Key a Controls PTZ by connecting with keyboard controller or 7p terminal block connects the power keyboard controller DVR using RS 485 communication standards DVR or video device and etc to the camera s main body Refer Installation Using Surface Mount Bracket of page 10 for the connection of the terminal block Camera 1 Camera 2 Camera n Power Input Slot Video Input Slot Power EE ERE S Please check the correct rated power E
31. e linked with preset run means off 1 means on Gi PRESET SETUP LABEL Edits label to show on monitor when preset runs Max 10 alphabets are allowed Including space a N LABEL PRESET1e gt _j _ Ot i234567890 OK ABCDEFGHIJ CANCEL KLMNOPQRST UVWXYZabcd E opqrstuvwx Vgs j av PRESET NO 1 lt EDIT SCENE gt lt LABEL gt CLRPRESET CANCEL CAM ADJUST GENERAL ALARM OUT BACK EXIT lt Press Near Enter Key a LABEL PRESET1 E ORR ee 234567890 OK ABCDEFGHIJ CANCEL KLMNOPQRST UVWXYZabcd efghi k Imn opqrstuvwx Vaasa ana Press Near Enter Key d LABEL PRESET1 SKYE cue amp 1234567890 0K ABCDEFGHIJ CANCEL KLMNOPQRST UVWXYZabcd efghi k Imn opqrstuvwx V2 o Preset NO for Label Input Cursor The character which cursor is located will be input or edited Q Cursor Selecting Alphabet Using Left Right Up Down of joystick move to an appropriate character from the character set Space If you want to use blank choose space character Back Space If you want to delete a character before use back space character lt LABEL Alphabet Input If you complete the label editing move cursor to OK and press near key to save completed label To abort current change move cursor to CANCEL and press near key 4 PRESET SETUP PRESET NO 1 lt EDIT
32. ee Menu of the Press Press Far wf Near Enter gt Choose the Key Value N DISPLAY SETUP y CO00GRQ4 222222 z x y Move the Cursor Choose Menu Shift to the Sub Chosen Menu Joystick Up Joystick Down O Change the Value la DISPLAY SETUP N General Rules of Menu Operation This page explains how to operate the OSD menu using keyboard controller Read the manual of the keyboard controller If there are no keys or functions described below refer the manual of the keyboard controller Move the Cursor Up Down to Choose Menu To move from items to item in the menu move the joystick Up Down Shift to the Sub Menu of the Chosen Menu For all menu level to go into sub menu press near enter key Choose the Value To change the value press near enter key to move the cursor to the value Change the Value Move the joystick Up Down to change the value Move to the Previous Screen Press near key to save values and press far key to cancel values then go to the previous screen The menu items surrounded with lt gt always have its sub menu To move to the sub menu press near enter key This screen is the main menu of the Q DISPLAY SETUP Q This screen is the sub menu of DISPLAY SETUP on the screen O Qis the value of the each content 21 OSD Menu Contents OSD Menu
33. era moves to pre defined position and preset characteristics such as label and relay outputs show on monitor Refer screen 4 If a selected preset is not defined UNDEFINED shows on monitor lt EDIT SCENE gt Moves to EDIT SCENE setup screen EDIT SCENE 1 Using joystick move camera to desired position 2 Using zoom key move camera to desired screen size 3 By pressing near key the save current PTZ data PRESET SETUP If the preset is defined the information will be shown on the OSD menu with the setting and the alarm device if defined will be activated PRESET NO 1 128 Excluding 95 lt EDIT SCENE gt lt LABEL gt Edits Label to show on monitor when preset runs If the preset is not defined this is not shown Refer following page to setup label CLR PRESET CANCEL OK Deletes current preset data If the preset is not defined this is not shown CAM ADJUST GENERAL SPECIAL CAM ADJUST_GENERAL The general mode means that WB or AE defined ROOT MENU gt CAMERA SETUP will be applied to this preset CAM ADJUST_SPECIAL The Special mode means that WB or AE can be set up independently or separately for each preset in each preset setup menu Special WB AE value should activate only when the camera arrives at each preset location During jog operation general WB AE value should be applied Refer following page to set special WB AE ALARM OUT 1 Relay output can b
34. eset key 142 3 Delete Scan To delete scan use OSD menu Pattern Pattern function is that a camera memorizes the path mostly curve path by joystick of controller for assigned time and revives the path exactly as it memorized Refer page 31 ROOT MENU gt FUNCTION SETUP gt PATTERN SETUP for more detailed information 1 Set Pattern To set pattern use OSD menu 2 Run Pattern Method 1 If there is pattern key on the keyboard controller Pattern key Pattern number 1 4 Enter key Ex Run pattern 2 Pattern key 2 Enter key Method 2 If there is no pattern key on the keyboard controller Preset key Pattern number 1 4 130 Ex Run pattern 2 Preset key 132 3 Delete Pattern To delete pattern use OSD menu Group The group function allows running sequence of presets pattern and or scans Refer page 32 ROOT MENU gt FUNCTION SETUP gt GROUP SETUP for more detailed information 1 Set Group To set group use OSD menu 2 Run Group Method 1 If there is group key on the keyboard controller Group key Group number 1 8 Enter key Ex Run group 2 Group button 2 Enter key Method 2 If there is no group key on the keyboard controller Preset key Group number 1 8 150 Ex Run group 2 Preset key 152 3 Delete Group To delete group use OSD menu Schedule The schedule function allows running an appropriate function like
35. essential to proper schedule function Max 7 schedules are allowed MASTER ENABLE ON OFF Decide whether schedule function is active or not DAY UNDEFINED ALL WKD SUN MON Set the day for scheduling Undefined Inactivate All Applies to every day WKD Applies to every day except Sunday SUN MON Applies to designated day only TIME 00 00 23 59 hour min Set the time ACT NO HOM HOME PRS Preset 1 128 Excluding 95 Set the function and no SCN Scan 1 8 PTN Pattern 1 8 GRO Group 1 8 EgUnlike the group the undefined function can be assigned in schedule However no action is taken at the schedule ON ON OFF Decide to make this rule effective or not O SCHEDULE SETUP Assign Value Each field DAY TIME ACT NO ON can be selected by Left Right keys and the values in the field are changed using Up Down keys OSD FUNCTION SETUP gt SCHEDULE SETUP Q nn SCHEDULE SETUP MASTER ENABLE OFF DAY TIME ACT NO ON gt ALL 12 00 PRS 1280N 2 UNDEFINED 3 UNDEFINED 4 UNDEFINED 5 UNDEFINED 6 UNDEFINED CE ot aaa ea ate SCHEDULE SETUP Save Edited Setting To save data and exit press near key If there are rules conflicts to each other the higher number is the higher priority has e g The camera will move to Preset 127 at 12 00 on every Wednesday although Preset 128 and 127 were set at 12 00 on ever
36. f ID is 0 255 Factory default of camera ID is 1 Camera ID will be effective without rebooting the camera Drilling the Hole on the Ceiling To pass cables through the ceiling drill a hole 30mm diameter on the ceiling panel Fix the Surface Mount Bracket Pass the cables to the 34 pipe hole and screw the surface mount bracket to the ceiling Rubber Gasket Before installing the gasket the hole in the center is to be cut by knife when only necessary When installing gasket the protrusion of the gasket should be matched with the groove joint of the bottom of the surface mount bracket Connect the Cables Connect wire cables to the terminal blocks Refer page 16 17 for details Connect the Terminal Blocks Connect the terminal blocks to the main body Fix the Main Body Screw the main body to the surface mount bracket by screwing 4 lock up screws Detach the Protection Vinyl Detach the protection vinyl from the dome cover 10 Installation Using Surface Mount Bracket Drilling the Hole on the Ceiling Rubber Gasket Fix the Surface Mount Bracket Connect the Cables Connect the Terminal Blocks Fix the Main Body Detach the Protection Vinyl Installation Using Flush Mount Ring Bracket Option Drilling the Hole on the Ceiling l Po WJ Separate the Lock up Screws from the Main Body Q wire the Cables and Ter
37. he 2nd pos camera turns on its axis by 360 in CW direction and then it turns on its axis by 360 in CCW direction If one preset is not defined between the 1st POS and the 2nd POS If case that a position assigned is NOT USED camera turns on its axis by 360 in CW direction from the preset which is NOT USED and then it turns on its axis by 360 in CCW direction 2st POS 7 1st POS e 2 CCW direction 1 CW direction SCAN NO 1 8 Select scan number to edit If a selected scan is defined 2 presets will be displayed in the 1st position and the 2nd position 1ST POS PRESET 1 128 NOT USED Set up the 1st position for scan function If a selected preset is not defined UNDEFINED will be displayed as shown below h SCAN SETUP AN NO 1 1ST POS PRESET 1 PO NOT USED COARN CANAFrrA UNDEFINED Eg Undefined preset cannot be assigned as position If you press near key when the selected preset is UNDEFINED the preset will returned to previous position Available preset or NOT USED 2ST POS PRESET 1 128 NOT USED Same as the 1st pos setup SCAN SPEED 1 SEC 180 SEC Sets the scan speed CLEAR SCAN CANCEL OK Deletes the data in current scan OSD FUNCTION SETUP gt PAT TERN SETUP SI FUNCTION SETUP lt PRESET SETUP gt lt SCAN SETUP gt lt PATTERN SETUP gt lt GROUP SETUP gt lt SCHEDULE SETUP gt BACK
38. hings etc or containers filled with water on top of the camera Doing so may cause personal injury due to fire electric shock or falling objects 7 Do not install the unit in humid dusty or sooty locations Doing so may cause fire or electric shock 8 If any unusual smells or smoke come from the unit stop using the product In such case immediately disconnect the power source and contact the service center Continued use in such a condition may cause fire or electric shock 9 Ifthis product fails to operate normally contact the nearest service center Never disassemble or modify this product in any way x10 Anti vandal 10 When cleaning do not spray water directly onto parts of the product Doing so may cause fire or electric shock Speed Dome Camera User s Manual Ver 3 1 2009 09 Precautions Operating e Before using make sure power supply and others are properly connected e While operating if any abnormal condition or malfunction is observed stop using the camera immediately and then contact your Special dealer Handling e Do not disassemble or tamper with parts inside the camera e Do not drop or subject the camera to shock and vibration as this can damage camera e Care must be taken when you clean the clear dome cover Especially scratch and dust will ruin your quality of camera Installation and Storage e Do not install the camera in areas of extreme temperature which exceed the allowable range
39. in the same pan orientation Therefore all function data depending on pan orientation such as preset scan pattern group and privacy zone mask are not useful any more accordingly However even in this case you can reuse the data if you redefine set home position on the previous home position For setup refer EDIT SCENE on page 28 O SET NORTH DIRECTION The direction will be displayed on the right bottom of the screen pan is 0 and direction is N LINLARN JLLLU I I AIWAN U LET L O D EIN FAN HEATER SETUP Sets the fan heater enabled disabled according to the temperature This menu will be displayed only for fan heater model FAN RUN TEMP 30 C 80 C 86 F 176 F Above this temperature the blower fan will start automatically HEATER RUN TEMP 10 C 20 C 14 F 68 F Below this temperature the heater will be tuned on automatically 39 OSD SYSTEM INITIALIZE Dimensions Q SYSTEM INITIALIZE T ERR STEN I NITIALIZE wide wales Initializes to the camera setting CLEAR ALL DATA NO wee DISPLAY SET NO CLEAR ALL DATA ON OFF m LR MOTIOM SET NO Deletes all configuration data such as display camera motion setup and m CLRFUNCTION SET NO so on REBOOT CAMERA N REBOOT SYSTEM NO CLR DISPLAY SET ON OFF BACK Initializes display configuration EXIT S CLR CAMERA SET ON OFF Initializes camera configuration CLR MOTION SET ON OF
40. ion Brackets Specifications Product amp Accessories Please check if all the camera and accessories are included in the package Main Body Camera module screws terminal block slot and DIP switches are included Surface Mount Bracket It is used when installing the camera right on to the ceiling To install the camera with the surface mount bracket the bracket needs to be separated from the main body then needs to be re assembled the bracket and the main body according to the order Screw amp Plastic Anchor Screws are used to fix the surface mount bracket to the ceiling Plastic anchors are used to tighten the screws to the hole by inserting them into the holes in advance Terminal Block Power video communication and alarm input cables are connected through the terminal blocks O Torx Screw Driver It is used to screw unscrew the fixed screws on the main body O Rubber Gasket It is installed between the surface mount bracket and wall wall mount bracket to prevent the water leakage Manual Please read the manual carefully before installing Screw amp Plastic Anchor 4pcs i Owain Body Surface Mount Bracket Terminal Block x2 5P 7P Torx Screw Driver Manual Rubber Gasket Parts Name amp Functions e O Dome Cover OCA se A Lockup Screw Main Body ra 7P Terminal Block Slot 5P Terminal Block Slot Da DIP Switch 23
41. ling Mount Bracket Pass the cables into the ceiling mount bracket and screw the ceiling mount bracket to the ceiling Fix the Surface Mount Bracket Pass the cables through the hole of the surface mount bracket screw the surface mount bracket to the ceiling mount bracket Wire Cables Wire the cables to the terminal block Refer page 16 17 Connect the Terminal Blocks Connect terminal block to the main body Refer page 10 Q Fix the Main Body Screw the main body to the surface mount bracket Screws are included in the main body Detach the Protection Vinyl Detach the protection vinyl from the dome cover 12 Drill nian Fix the Anchor Bolts Rubber Gasket Fix the Ceiling Mount Bracket Fix the Surface Mount Bracket Wire Cables connect the Terminal Blocks Fix the Main Body Detach the Protection Vinyl Fix the wall Mount Bracket Rubber ee Drill the wall a Fix the Anchor Bolts Rubber Gasket Fix the Surface Mount Bracket Wire Cables O Connect the Terminal Blocks Fix the Main Body Detach the Protection Vinyl Installation Using Wall Mount Bracket Option 1 Installing on the Concrete Wall Drill the Wall and Fix the Anchor Bolts On the wall drill a hole 6mm diameter 50mm depth and fix the anchor bolts Fix the Wall Mount Bracket 1 Drill a hole 20mm diameter on the pipe of the bracket to p
42. minal Blocks S 7 NAA Fix the Flush Mount Ring Bracket to the Main Body Onw Omn _ ap Fix the Main Body A i Drilling the Hole on the Ceiling To pass cables through the ceiling drill a hole 7Omm diameter on the ceiling Separate the Lock up Screws from the Main Body Separate the 4 lock up screws from the main body in advance Fix the Flush Mount Ring Bracket to the Main Body Fix the flush mount ring bracket to the main body using torx screws Connect Wire the Cables and Terminal Blocks Connect wire cables to the terminal blocks Refer page 16 17 for details Fix the Main Body Screw the main body with the surface mount bracket to the ceiling using the screws on the surface mount bracket Detach the Protection Vinyl Detach the protection vinyl from the dome cover 11 Installation Using Ceiling Mount Bracket Option 1 Installing on the Concrete Ceiling Drill the Ceiling and Fix the Anchor Bolts On the ceiling drill a hole 6mm diameter 50mm depth and fix the anchor bolts Fix the Ceiling Mount Bracket 1 Drill a hole 20mm diameter on the pipe of the bracket to pass the cables 2 On the fixed anchor bolts attach the rubber gasket and screw the ceiling mount bracket 2 Installing on the Wooden Ceiling Drill the Ceiling To pass cables to upside of ceiling drill a hole 30mm diameter on the ceiling Fix the Cei
43. move the focus to set alarm type function name and function no 3 By pressing near key save the current setting 27 O FUNCTION SETUP OSD FUNCTION SETUP gt PRESET SETUP FUNCTION SETUP Configure 5 special functions with this menu lt PRESET SETUP gt Moves to PRESET SETUP screen lt SCAN SETUP gt Moves to SCAN SETUP screen Refer page 30 lt PRESET SETUP gt lt SCAN SETUP gt lt PATTERN SETUP gt lt GROUP SETUP gt lt SCHEDULE SETUP gt BACK EXIT S A Press Near Enter Key PRESET SETUP PRESET NO lt PATTERN SETUP gt Moves to PATTERN SETUP screen Refer page 31 lt GROUP SETUP gt Moves to GROUP SETUP screen Refer page 32 lt SCHEDULE SETUP gt Moves to SCHEDULE SETUP screen Refer page 34 OSD FUNCTION SETUP gt PRESET SETUP 28 1 UNDEFINED lt EDIT SCENE gt BACK EXIT A Select lt EDIT SCENE gt Press Near Enter Key N EDIT SCENE PRESET1 MOVE TO TARGET POSITION LNEAR SELECT FAR CANCEL Oye amp A Press Near Enter Key i PRESET SETUP PRESET NO 1 lt EDIT SCENE gt lt LABEL gt CLRPRESET CANCEL CAM ADJUST GENERAL ALARM OUT BACK EXIT A PRESET SETUP Undefined Screen 127 presets from the number 1 to 128 can be assigned excluding preset 95 reserved for menu PRESET NO 1 128 Excluding 95 If a selected preset is already defined cam
44. o select the digit 4 By pressing near key save current setting PARKING ACTION HOME PRESET 1 128 SCAN 1 8 PATTERN 1 4 GROUP 1 8 Select the action of parking Move joystick Up Down to choose the appropriate action OSD MOTION SETUP MOTION SETUP 4 Press Near Enter Key ALARM INPUT SETUP ALARM 1 N Q NOT USED ALARM 2 N 0 NOT USED BACK EXIT Press Near Enter Key i 2 a ono ALARM INPUT SETUP ALARM 1 wo NOT USED ALARM 2 N NOT USED BACK EXIT Joystick Right ALARM INPUT SETUP ALARM 1 N Q ALARM 2 NO NOPUSED BACK EXIT Joystick Down ALARM INPUT SETUP ALARM 1 N Q 1 ALARM 2 N0 WOT USED BACK EXIT ALARM INPUT SETUP If an external sensor is activated camera will move to corresponding action Alarm Type N O Normal Open N C Normal Close Sets sensor input type Refer page 14 for more detailed information Alarm Action NOT USED HOME PRESET 1 128 SCAN 1 8 PATTERN 1 4 GROUP 1 8 Assign counter action to each alarm input Among 149 actions choose the action as explained below ALARM INPUT SETUP Type Setup 1 Move joystick Up Down to set alarm type 2 Move joystick Left Right to set alarm action O ALARM INPUT SETUP Alarm Action Setup 1 Move joystick Up Down to set the action HOME PRESET SCAN PATTERN GROUP and no 2 On screen 5 move joystick Left Right to
45. preset scan group pattern home move at the designated day and time Refer Page 34 ROOT MENU gt FUNCTION SETUP gt SCHEDULE SETUP for more detailed information 19 OSD Information d Preset Label PRESET LABEL Date Time 2 M R 2009 OFM RS FICAM 1 359 180 x100 S A A Image Flip oe h PATTERN G Action Title Temperature Alarm Input Information Relay Out Information 2a C 2 0 1 ap Oomes Direction E o Zoom Magnification Camera ID Preset Label The label stored for specific preset Refer page 29 for setting preset label ROOT MENU gt FUNCTION SETUP gt PRESET SETUP gt LABEL Date Time Shows the current date time Refer page 38 for setting date time ROOT MENU gt SYSTEM SETUP gt DATE TIME SETUP Image Flip Shows that images are currently reversed by auto flip function Refer page 36 for setting image flip ROOM MENU gt CAMERA SETUP gt IMAGE FLIP Camera ID The current camera ID The camera ID is identical with the address of ROOT MENU gt SYSTEM INFORMATION O Action Title Shows the current action titles of the camera Action Title SET PRESET 123 Means to store preset 123 PRESET 123 Means it reached preset 123 PATTERN 9 Means tthe camera is running pattern 9 SCN 1 PRESET 123 Means the camera is running scan 1 UNDEFINED Means the action received is not defined
46. s scan function 1 8 Preset key 151 158 Runs group function 1 8 Preset key 161 Sets relay output to OFF Preset key 161 Sets relay output to ON Preset key 165 Sets auto calibration to ON Preset key 166 Sets auto calibration to OFF Preset key 167 Zoom proportional jog ON Preset key 167 Zoom proportional jog OFF Preset key 170 Sets camera BLC mode to OFF Preset key 171 Sets camera BLC mode to HIGH Preset key 174 Sets camera focus mode to AUTO Preset key 175 Sets camera focus mode to MANUAL Preset key 176 Sets camera focus mode to SEMI AUTO Preset key 177 Sets day amp night mode to AUTO1 Preset key 178 Sets day amp night mode to NIGHT Preset key 179 Sets day amp night mode to DAY Preset key 190 Sets OSD display mode to AUTO Except privacy mask Preset key 191 Sets OSD display mode to OFF Except privacy mask Preset key 192 Sets OSD display mode to ON Except privacy mask Preset key 193 Sets all privacy mask display to OFF Preset key 194 Sets all privacy mask display to ON Preset key 195 Sets fan heater to ON Turning off after 5 min turn to auto mode Preset key 196 Sets fan heater to OFF After turning off turn to manual mode Preset key 197 Fan ON Turning off after 5 min turn to auto mode Preset key 198 Fan OFF After turning off turn to manual mode Preset key 200 Sets digital zoom to ON Preset key 201 Sets digital zoom to OFF 18
47. y Wednesday 7 D SCHEDULE SETUP N 35 36 ns nnn OSD CAMERA SETUP gt WB SETUP CAMERA SETUP Setup the general functions of zoom camera module FOCUS MODE AUTO MANUAL SEMIAUTO Sets camera focus mode SEMIAUTO This mode exchanges focus mode automatically between manual focus mode and auto focus mode Manual focus mode activates in preset operation and auto focus mode activates when jog operation starts MANUAL With manual mode at presets focus data is memorized in each preset in advance and camera calls focus data in correspondence with presets as soon as camera arrives at a preset DIGITAL ZOOM ON OFF Sets digital zoom function to ON or OFF If this is set to OFF optical zoom function runs but zoom function stops at the end of optical zoom magnification IMAGE FLIP ON OFF Sets if the image should be reversed or not CAMERA SETUP FOCUS MODE SEMIAUTO DIGITAL ZOOM QN IMAGE FLIP OFF lt WHITE BALANCE SETUP gt lt AUTO EXPOSURE SETUP gt BACK EXIT N 4 Press Near Enter Key 4 N WB SETUP WB MODE AUTO RED ADJUST BLUE ADJUST BACK XIT x Press Near Key Joystic Down a WB SETUP WB MODE MANUAL RED ADJUST te BLUEADJUST 40 BACK EXIT S Press Near Enter Key a N WB SETUP WB MODE MANUAL RED ADJUST 117 BLUE ADJUST 40 BACK EXIT S d Joystic Down a N WB SETUP WB

User`s Manual Speed Dome Camera

Contents

Download Pdf Manuals

Related Search

Related Contents