Installation Manual
Contents
1. Tab In Ceiling Installation Manual Part List IR Smart Remote Control O AAA ep Le lt gt EI After installation please store instructions for future reference Areas Required Protected areas Operating areas WARNING To reduce the risk of fire or electric shock do not expose this apparatus in or near rain or moisture 1 Read and follow all instructions and warnings in this manual Keep for future reference 2 Do not use this apparatus near water 3 Clean only with a dry cloth 4 Do not block ay ventilation openings Install according to manufacturer s instructions 5 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 6 Do not override the safety purpose of the polarized or grounding type plug A polarized plug has two blades one wider than the other A grounding type plug has tow blades and a third grounding prong The wide blade or the third prong is provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet Protect the power cord from being walked on or pinched particularly at plug convenience receptacles and the point where it exits from the apparatus 8 Only use attachments accessories specified by the manufacturer 9 Unplug2. LL RS232 serial port setting Central controller Baud rate 2400 Data bit 8 de Control Unit Provided by Parity bit N others i e Crestron AMX Stop bit 1 Default HEX code FF101100DD Up FF 1011 00 EE Down FF101100CC Stop Wiring Diagram After finish the serial port setting connect the RJ2 and RS232 according the diagram Fill in the HEX code into the serial control software and press the learn button for about 1 second LED will start flashing Release the learn button and send the code from serial control software LED will stop flashing Once the learning procedure is done the screen will be controlled by serial port 6 RF remote control kale RF remote control frequency is 433MHz which has been setup in factory should work right away however in case it cannot work atfirst time you will need to use the learn function Please refer to the following method to finish learn function set up Press the hole atthe bottom of the left end cap partfor 3 seconds indicated by a light flash then pressthelearn hole ofthe remote control the receiver led light will become normally on from flash situation How to pair remote control and wireless trigger You need to pair new replaced RF remote control and wireless trigger the operating steps is the same with above If it is failure please press the learn code hole at the bottom of the left end cap part for 5 seconds the led light will flash
3. dirt on regular occasions 2 To clean the screen material use warm soapy water only never use chemicals or abrasives as this will damage the surface of the material which in turn will affect the viewing quality of your screen Preparing Installation 1 Measure the length of the trim panel A ja A AA a 14000 Open the ceiling with the length of A 20mm and the width of 140mm 2 The distance between two ceiling brackets would be A 120mm There is 48mm between right and left screw holes on the ceiling brackets and 60mm between front and back holes Expansion Screws Anchors are needed depending on the ceiling material Always ensure that the ceiling can support the weight of the screen Assemble the Components Slide four of M6 8 screws into the rail Install the screen brackets leave on the top of screen upside down 30mm sticking out the edge of the screen Tie the brackets with the nuts to make sure the screen to vibrate or slide during the installation Fix the threaded mounting rods to ceiling Use M8x80 anchor bolt for the concrete ceiling or M5x40 self brackets by using M10 nuts on the top and bottom of the brackets brackets to the ceiling Hanging Installation Attach one end of mounting rod to the screen bracket using M10 nut Al on the top and long nut in the bottonr as showing in the picture Make sure ee leave some space so the bracket can move when installing
4. this apparatus during lighting storms or when unused for long periods of time 10 Refer all servicing to gualified service personnel Servicing is reguired when the apparatus has been damaged in any way such as when the power supply cord or plug is damaged liguid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 11 Do not expose this eguipment to dripping or splashing ensure that no objects filled with liguids such as vases are placed on the eguipment 12 To completely disconnect this equipment from the AC mains disconnect the power supply cord plug from the AC receptacle 13 To avoid overheating the motor do not continually retract and lower the screen for over 3 minutes or more than 6 times Troubleshooting O Power cable to the film screen is incorrectly connected or plugged into an outlet that does not have power O Check connections and verify power on the outlet Screen does not react to any control Screen goes lower than desired or does Not Adjust the up and down limites as described rectract far enough Check the batteries in the IR RF remote that you are using IR RF control O Ensure that you are within range of the remote being does not work used The factory remote will work at a distance of up to 15m most situations 1 Do not clean the Screen case with water Use a dry cloth and keep clear of dust and
5. another end tapping wood screws forthe wood ceiling to attach the ceiling Use the same way to install another end of the screen The screen should be parallel with the ceiling after the installation Clip in the plastic cover as shown in the picture The screen when installed should look same as the diagram N Please make sure connections are compatible and safe Control Wiring Diagram RS232 control interface 12V trigger External IR Receiver IR Learn Hole P i Receiver O ri 1 ri K A a a E A n ci a Sa 7 Power Connections using specified power interface under rated voltage Trigger out LA 5V 12V DC The wireless trigger has been set up at factory should work Plug the trigger into trigger port on projector straightly right away however in case itcannot work atfirsttime you to synchronize the screen up and down with projector will need to use the learn function Please refer to the following power cycle method to finish learn function set up When projector power open the screen goes up Please press the hole at the bottom of the left end cap part for projector power close the screen goes down 3 seconds indicated by a light flash then press the learn hole automatically of the wireless trigger the receiver led light will become normally on from flash situation Now we finish the learn code function RS232 serial port control
6. en lower the screen and retract it repeat the action until the screen could stop at the desire position 1 Set the remote control at down position 2 While lower the screen if the screen could not be fully down use the accessory of 6 angles screw adjusting the down limit screw turning the screw around according to the direction until the screen is at the desire position 3 If you want shorten the top black border use the accessory of 6 angles screw adjusting the down limit screw turning the screw around according to the direction then retract the screen and lower it repeat the action until the screen is at the desire position
7. quickly which will clear all the codes just reply the above steps to finish learn code function IR smart remote control IR window Smart Remote Control The IR remote control has been set up at factory should work right away please refer to IR remote control user manual to understand more applications String tension adjustment more tension less tension Caution Keep the controller away from high temperature and humidity Please change the battery when the signal is low Please remove the battery from the remote control when the controller is not being used for a long time Please use the same type of battery as originally supplied If the receiver is to be out of use for a long time please turn the electricity off or unplug it Adjusting the screen length limits We only recommend that experienced AV installers undertake these procedures Drop Limit DOWN v lo e UP Retraction Limit Up Limit adjustable screw Down Limit adjustable screw 1 Set the remote control at up position 2 While retract the screen if the screen could not be fully retracted use the accessory of 6 angles screw adjusting the up limit screw turning the screw around according to the direction until the low bar at the desire position 3 if the screen exceed the desire position of the top use the accessory of 6 angles screw adjusting the up limit screw turning the screw around according to the direction th
Download Pdf Manuals
Related Search