Collector GPRS User Manual
Contents
1. connected COMM turns on every 5 seconds Guardus connected to Collector GPRS data collect COMM red light turns on ing interface for G3 and G5 or IrDA interface for G7 Guardus downloads data to Collector GPRS Guardus sounds one time and COMM red light blinks Guardus finishes the download COMM red light turns off and Guardus sounds three times Guardus is disconnected from Collector GPRS COMM green light and GPRS green light blink once Collector GPRS data collector sequence Data collecting from a Guardus to a Collector GPRS is simple and quick easily executed by the user Collector GPRS is permanently on active status without any on off key NOTE Be sure all Guardus to be downloaded on Collector GPRS were programmed with PROGuard 4 0 or high er or with GOL Former versions won t be processed Collector GPRS User Manual To download data from Guardus G3 and G5 to Collector GPRS follow these steps 1 Attach Guardus on the data collector interface to download the stored data 2 Wait for the COMM red light and SUCCESS sound signal PLIM inform ing the communication beginning 3 Keep Guardus in contact with the data collector interface while the COMM red light blinks It means the data is being transferred to Collector GPRS 4 Wait for the sound Restart three BIPS signalizing the download has finished 5 Detach Guardus from Collector GPRS interface 6 Wait unti2. Guardus downloads cole Infrared interface used for downloading the data collected from Guardus G7 or Collector Power supply connector Buzzer sound hole GPRS configuration Collector GPRS User Manual Charging the Collector GPRS Battery Collector GPRS is powered by a lithium polymer Li Polymer rechargeable battery pla ced on the backside of the device This battery must be recharged when the Collector GPRS sounds a beep each 20 seconds just like a cell phone does A totally discharged battery takes aproximately 4h30min to fully charge When recharging has finished the COMM green light and GPRS green light will blink simultaneously NOTE1 The battery status can be checked through the Con tronics Collector GPRS Tool at the status bar Battery Status NOTE2 The Collector GPRS will not transmit the data while the charger is connected Power supply input used for battery charging SIM Card chip Installation To insert a SIM Card chip on Collector GPRS execute the following steps 1 Open the Collector GPRS backside cover removing the screws and disconect the battery holding and pulling the white connector 2 Under the battery you will find the SIM Card slot Slide the SIM Card into the slot to insert it 3 Be sure that the SIM Card s metalic contacts are turned to the board 4 Slide the SIM Card support as showed on the figure until you feel it locks 5 Put back the battery with
3. and PC This transfering is processed when the Collector GPRS connects itself to the PC through GM GPRS mobile communication GOL BUSINESS Configuration To receive the data from Collector GPRS GOL BUSINESS monitoring system must be pro perly configured You must define the Collector GPRS as the interface assigned to send you the data from Guardus to your computer 10 Collector GPRS User Manual For a correct configuration follow these steps 1 Access the monitoring system GOL BUSINESS 2 In the configurations area access GolConfig 3 On GolConfig configuration screen access the tab GolComm 4 Access the tab Download Interface 5 Select the check box related to the Collector GPRS interface choosing the communication port reserved to receive the downloads transmitted by Collector GPRS 2 Configuration ProGolWinfi GolComm i BobxMLTranslator GolFileCatcher GolFilePitcher GolFilelmport GolReportGen GolReportDeployer GolScheduler GolTraxxerEngine GolKeeper GolLog GolDataBase Localiza o Communication port Active A 5131 Automatic initiate Server 127 0 0 1 Location l c Arquivos de programas Contronics G o G olComm G olComm EXE Download interface T ansfering file location Guardus Pomet T download using serial connector CI Collector download using USB connector Serial Communication Connector COM L ie No intial configuration CI Remote ISP NET
4. inter face is installed 3 Still on tab Settings on the right sided table insert conectivity information about your GSM operator APN user password and way of authentication 4 On Data Collector you will find the option Clean Guardus after download Check it if you want to clean up the downloaded data from Guardus to Collector GPRS 5 Click on button Write to send the configurations to Collector GPRS Collector GPRS User Manual If one of these settings was accidentally erased contact the Contronics support and ask about the data i Warning The settings GolComm Server and DNS Server must not be changed for GOL PREMIUM users to recover the correct settings ZI Collector GPRS Seles Interface Help Support Identification Serial Number Battery Status II Hardware version Monitor Firmware Version Application Firmware Version i IL RS General Settings Connectivity GolComm Server APH Address 0 0 00 apn com User Part 0 UZET Password Data Collector password Clean Guardus after download Authentication Type PAP L ONS Server Freferred Alternate 0 0 0 0 mono Collector GPRS data download Collector GPRS uses GOL monitoring system to transfer data between Collector GPRS
5. Collector _ User Manual collecto Collector GPRS User Manual This manual is also available on the CD ROM bundled with the product or at Contronics site Summary Introduction Collector GPRS Components Optional Accessories System Requirements Overview Charging the Collector GPRS Battery SIM Card chip Installation Data Colleting Collector GPRS Settings GOL Business Settings GOL Premium Settings Collector GPRS data download Signalling Interpretation Technical Specifications Recycling Acknowledgements declarations N Collector GPRS User Manual Introduction Collector GPRS is a portable electronic device used for collecting storing and transfe ring the data coming from the Contronics wand Guardus to a computer Its main be nefits are Allows downloads from several different Guardus wands right from the locations where they are being used e Sends the collected data to the computer at the operation center through GSM GPRS allowing on line management of the surveillance system This User Manual guides the operation of this device enabling its proper and maximum use The terms used in this manual follow the standard application in electronic sur veillance in conformity to the security market SIM Card not included proper activation from GSM mobile operator is necessary to use Collector GPRS Collector GPRS Components Collector GPRS data collector gt C
6. Download using Intranet or Internet CI Download i RF USB download using USB connector 5 Communication port l i lt gt No intial configuration CI USB Cable download using USB connector Communication port Automatic Collector GPRS download on computer Besides transmitting to aPC using a GSM GPRS mobile system Collector GPRS can trans mit the data downloaded from the wands directly through an IrDA interface if the GSM GPRS is out of signal 1 Align the IrDA window of your interface e g USB Communication Cable with Collector GPRS IrDA window 2 Wait finishing the data transfer and for the confirmation sound signalling three BIPS 11 Download iRF IrDA Collector GPRS User Manual IrDA IrDA i IMPORTANT The data downloads through IrDA will only be viewed for GOL BUSINESS monitoring system users Signalling Interpretation Collector GPRS signals through lights its working status Signalling Status COMM red light blinks every five seconds COMM red light turns on COMM red light blinks fastly COMM green light and GPRS green light blink once COMM green light and GPRS red light turn on COMM red light and GPRS green light turn on GPRS red light turns on GPRS green light turns on GPRS green light blinks three times GPRS red light blinks three times The two red lights blink simultaneously The two green lights blink simultaneously COMM red light and G
7. PRS green light blink and GPRS green light blinks once more COMM red light and GPRS red light blink and GPRS red light blinks twice more 12 Collector GPRS active and waiting transmission or con tact with a Guardus Collector GPRS waiting to communicate with a Guar dus or a command from PC for firmware updating Data from Guardus being transmitted to Colletor GPRS Collector GPRS is ready to receive downloads from the next Guardus Collector GPRS starts to register with GSM operator Collector GPRS starts GPRS communication Collector GPRS waiting for the data transmission to begin or confirmation from GOL Collector GPRS data being transmitted Transmission completed and confirmed Transmission interrupted Collector GPRS battery being charged Collector GPRS battery charge completed Pending download to be transmitted Collector GPRS memory is full Collector GPRS User Manual Technical Specifications Power source Capacity Physical Characteristics Signalling Operating Temperature Humidity Limit Size Weight Recycling Li Polymer 1800 mAh battery 50 Guardus downloads High resistance plastic box with 2 signalling leds reading interface and IrDA ac tivation key GSM GPRS Quadriband 850 900 1800 1900 MHz Hearable for start and end of downloads emitted by Guardus and for data transmitting confirmation or interruption emitted by Collector GPRS Visual through LEDs powered up COMM tra
8. its rubber support oriented on the initial position and aligned with the cover lids 6 Reconnect the battery 7 Screw the cover back Warning Scratches and folds may damage the SIM Card chip Be careful when inserting remov ing or storing this chip Be sure the battery is disconnected before insert or removal of the SIM Card chip Check the battery and its rubber support position after openning the back cover put ting them back to the same position after SIM Card chip insertion Collector GPRS User Manual Data Colleting To download data place Guardus G3 e G5 to the collector interface or put Guardus G7 close to the IrDA interface The download will happen automatically Downloading will be informed through sound and light signals Data transfering Collector GPRS stores the collected data on its non volatile memory with the date and time of reading Collector GPRS data transmission is made through its GSM GPRS mobile phone system through the USB Communication Cable interface or via IrDA interface NOTE1 SIM Card not included proper activation from GSM mobile operator is necessary to use Collector GPRS NOTE2 The Collector GPRS will not transmit the data while the charger is connected Signalling sequence during Guardus download Communication between Guardus and Collector GPRS is confirmed by a sequence of sound and light signalling Actions Signalling Collector GPRS active and no Guardus
9. l the COMM green light and GPRS green light blink once be fore downloading another device on Collector GPRS repeating the cycle above if needed To download data from Guardus G7 to Collector GPRS follow these steps 1 Press the red button on the side of Collector GPRS to enable the IrDA interface 2 Wait for the COMM red light to turn on 3 Put Guardus G7 close to the Collector GPRS aligning the IrDA interface with the light on the reader interface of the wand to download stored data 4 Wait for the sound signal Success PLIM informing the communication beginning 5 Keep Guardus in this position aligned with the Collector GPRS IrDA inter face while the COMM red light blinks It means the data is being transferred to Collector GPRS 6 Wait for the sound Restart three BIPS signalizing the download has finished AL Attention Be sure you hear three BIPs from Guardus at the end of the communication If you hear only one BIP repeat the operation If the maximum download store capacity has been reached the IrDA and contact interfaces won t be enabled until you transmit at least one of these downloads stored on Collector GPRS memorv Collector GPRS Settings In order to receive the download stored on Collector GPRS it is necessarv to set it up through the Contronics Collector GPRS Tool assigning the GSM operator data and the address of the server in charge of receiving the downl
10. menu The ap plication will be placed in folder Contronics To set up the Collector GPRS choose the right option for you GOL Business or GOL Pre mium and execute the following steps acording to your subscription GOL Business Settings 1 Run Contronics Collector GPRS Tool 2 On the pull down menu click on the button Interfaces and select the communication port on which your inter face is installed 3 On the tab Settings go to the left sided table insert the address and the port where your GOL BUSINESS server is installed and configured to receive the transmissions from Collector GPRS 4 Right below on Data Collector you will find the option Clean Guardus after download Check it if you want to clean up the downloaded data from Guardus to Collector GPRS 5 Still on tab Settings on the right sided table insert connectivity information about your GSM operator APN User Password and Authentication Type 6 At bottom side on DNS Server fill the fields Preferred and or Alternate if you need to use a specific DNS server 7 Click on button Write to send the configurations to Collector GPRS GOL Premium Settings Contact Contronics Technical Support and ask about the configuration settings address and port for the GolComm server 1 Run Contronics Collector GPRS Tool 2 On the pull down menu click on the button Interfaces and select the communication port on which your
11. nsferring data COMM and GPRS and low battery COMM GPRS 20 C to 50 C 4 F to 122 F 95 without condensation Width 64 mm x Depth 95 mm x Height 25 mm 2 51 x 3 74 x 0 98 85 g 3 ozor 0 187 Ibs Ro At the end of its lifetime this device must be delivered in a collecting center for recycling and not be disposed on a regular domestic trash can You will be contributing for better environmental conditions Acknowledgements declarations Contronics and Guardus are trademarks owned by Contronics Automa o Ltda Microsoft and Windows are trademarks owned by Microsoft Corporation Contronics reserves the right to change discontinue production and or characteristics of any product without previous notice Q contronics Contronics Technologies Inc 8121 NW 68th Street Miami FL 33166 USA sales contronics com www contronics com October 2009 13 CONTRONICS www contronics com
12. oads Before using Contronics Col lector GPRS Tool vou need to install it on vour PC The installation process is simple and quick easilv guided through an installation wizard NOTE Communication between PC and Collector GPRS is made bv using USB Communication Cable with IrDA inter face communication This cable must be properlv installed before using it according to its user guide Collector GPRS User Manual Contronics Collector GPRS Tool installing To install Contronics Collector GPRS Tool execute the following steps 1 Open Contronics CD ROM and access the folder applications 2 Run file eng_collector_gprs_tool_10 exe 3 When a welcome screen shows up click on Next 4 Check and confirm the user information and click on Next 5 You will be required to choose a folder to install the application We suggest the path C Program Files Contron ics Common Files Collector GPRS already written on the destination folder field Click on Next 6 You will be asked to start If everything is ok click on Next Contronics Collector GPRS Tool install will begin 7 Wait for the install process to finish and click on Finish 8 A Contronics Collector GPRS Tool icon will be created on your desktop 9 Contronics Collector GPRS Tool is ready for use Run the Contronics Collector GPRS Tool through its icon created on your desktop or select it and press ENTER You can also find this application on the Start
13. ollectsthedatafromGuardus and sends it to a remote computer allo ctor GPRS wing on line management of your electronic surveillance system CD ROM Contains all documents and software you need to configure check and operate the Collector GPRS Battery Collector GPRS uses a lithium polymer Li Polymer battery as a power source Power Supply Used to charge the Collector GPRS battery Installation Guide E Helps the user to understand the installation configuration and working ta fundamentals of the Collector GPRS NOTE These items can be sold separately Collector GPRS User Manual Optional Accessories USB Communication Cable Allows Collector GPRS to be configured through a com puter Nylon Case Extra protection while carrying and using the Collector GPRS Syste m Req u i reme nts for Contronics Collector GPRS Tools To install Contronics Collector GPRS Tool and configure the Collector GPRS you will need the following minimum environment Computer equiped with Pentium I 500 MHz or similar or superior 280 MB free hard disk space 128 MB RAM e USB interface port e Micrososft Windows XP OS with Pack 2 or superior e Microsoft NET Framework version 2 0 or superior Overview MAN Indicating lights active status com Data collecting interface munication and batterv Cover to access batterv and SIM card Button to turn on the IrDA reader and start the
Download Pdf Manuals
Related Search