Home
        YOUR PO49X PIZZA OVEN CONNECTING TO POWER
         Contents
1. YOUR PO49X PIZZA OVEN    Our range of pizza ovens are manufactured in the United Kingdom by skilled  craftsmen using top quality materials to ensure many years of trouble free  service  provided the instructions contained within this hand book are followed     CONNECTING TO POWER    Before connecting your pizza oven to the electricity supply  please ensure that  the voltage of your electricity supply is the same as indicated on the serial  number plate     This appliance is supplied with a 13 amp plug to British Standard protected by  a 13 amp fuse     If the supply cord is damaged  it must be replaced by either the manufacturer   its service agent or a similarly qualified person in order to avoid a hazard     The green and yellow wire must be connected to the terminal in the unit  marked with the earth symbol  The blue wire must be connected to the  terminal in the connector block marked with the letter  N   The brown wire must  be connected to the terminal in the connector block marked with the letter  L      IMPORTANT   THIS APPLIANCE MUST BE EARTHED  The wires in the  mains lead are coloured in accordance with the above codes     The unit must be positioned so that the plug is accessible    UNPACKING    Whilst every effort has been made to ensure that your pizza oven reaches you  in perfect condition  we recommend that after unpacking the unit is thoroughly  cleaned with a sanitising agent    SITING YOUR PIZZA OVEN    Your pizza oven should ideally be sited in a dry well 
2. regulator controls the power supply to the bottom element  The  energy regulator should not be left on maximum after the required  temperature in the oven space has been achieved     The unit is now ready to start cooking     We recommend that produce is not placed within the pizza oven until the  desired operating temperature is achieved     CLEANING    Before attempting to clean your pizza oven it must be disconnected from the  electricity supply  WARNING  Do not wet electrical components     Fire brick base   This may be removed for cleaning   This appliance must not be cleaned with a water jet     General Cleaning   The unit should be cleaned using a non abrasive cloth and  warm soapy water  Abrasive creams and scourers should not be used on any  metal surfaces     SERVICING    There are no user serviceable parts in the unit    The Control Thermostat is labelled as follows    Caution  Filler reacts  with water  danger of fire and or etching    If the thermostat fails the unit must not be used and should be checked  by an authorised service agent taking the necessary precautions to  avoid personal injury     Lincat    WHISBY ROAD   LINCOLN  LN6 3QZ  TELEPHONE  01522 875565  FAX  01522 875575    PO49X  PIZZA OVEN    IS109  Important Information    Taking Care of Your Pizza Oven    
3. ventilated environment   with a gap of at least 50mm between the back and sides of the unit and  adjacent walls or other appliances    The base of your pizza oven will become hot and therefore should not be  placed directly onto wooden or formica surfaces also a gap of 25mm should be  kept between the unit and the surface on which it is situated  The height of the  unit can be set by adjusting the screw feet     Please note     To comply with safety regulations  please site your pizza  oven so that the plug is always accessible    STACKING TWO UNITS    The PO49X pizza oven can be stacked two high  if this is to be done ensure  that the previous siting instructions are followed     SWITCHING ON YOUR PIZZA OVEN    Plug in the unit and switch on the supply  The green neon will illuminate to  show that the unit has power connected  Turn the thermostat knob to the  required cooking temperature  top control knob  clockwise   and set the  energy regulator to maximum  between off and 6 anti clockwise  to preheat  the unit  The amber neons will illuminate to show that the elements are turned  on    The thermostat amber neon will go off when the unit has reached the required  temperature  When the unit is up to temperature turn the energy regulator  down to 3  This is only a recommend setting and should be set to suit  individual requirements  The lower amber neon will then only be lit when the  lower element is on and will go through a continuos cycle of on off  on off as  the energy 
    
Download Pdf Manuals
 
 
    
Related Search
    
Related Contents
Philips SRC3036/27 Universal Remote User Manual    Draytek Vigor N61  Minka Lavery 6551-84 Installation Guide  Intellinet Pro Series Network Dome Camera    圓ロ円ー日ーnロ・ 取扱説明書  Fördergeräte  Epson ActionScanning System II Parts User Manual  T。SHーBA 東芝街路照明器具取扱説明書 保管用    Copyright © All rights reserved. 
   Failed to retrieve file