OSCAR POS58 Line Thermal Printer User`s Manual
Contents
1. Printer Head UpperCover p Opening Button Lack Paper Sensor SPRT ash drawer interface Power swit Power socket oo Ommunication interface 2 2 Paper Installation POS58 adopts 57 5 0 5mm width thermal paper The steps of thermal paper installation are as the following 1 When there is no paper in the print head pls don t press FEED button to avoid affecting the life of printing head Opening open button to open the case cover and change paper 2 After paper case cover is closed pls do not draw the paper forwards or backwards with hands 2 3 Interface Connection 2 3 1 Parallel Interface Connection The Parallel interface of POS58 printer is compatible with CENTRONICS supports BUSY and ACK handshaking protocol it uses DB25 socket male the pin order of parallel port is as below shows 3 Pin Order of Parallel Port The pin assignment of parallel interface is shown as below Strobe pulse to latch data reading occurs at raising edge STB SPRT These signals represent the 1 bit to 8 bit of the parallel interface data each signal is at HIGHT level when data is logic 1 and LOW when data is logic 0 Answer pulse LOW level signal indicates that data have already been received and the printer gets ready to receive the next data A O ACK HIGH level signal indicates that the printer is BUSY and can not receive data BUSY HIGH level signal indicates that2. N ESS ee gt S ie OOOO O SPRT Introduction POS58 printer is a new type line thermal printer it features in fast speed print low print noise high reliability perfect print quality and ribbon needless avoiding the vexation of regular maintenance POS58 printer small in outline dimension simple operation and extensive application especially suitable for commercial cash register PC POS bank POS and all kinds of receipts print SPRT Chapter 1 Characteristic and Specification 1 1 Printing specification Printing method direct thermal Printing paper width 57 5 0 5mm Printing density 8 dots mm 384 dots line Printing speed approx 75mm s valid content of each line isn t over 25 Reliability Printing head life 100km MCBF 5 million lines Using condition Print 12 x 24 ASCII characters print 50 lines each time intermittent print repeatedly Each dot line printing at the same time should not exceed 25 each character line and one dot vertically printing repeatedly should not exceed 11 times Use specified thermal paper Valid printing width 48mm 1 2 Printing Paper e Thermal paper model TF50KS E Japan paper co ltd AF50KS E JUJO THERMAL e Thermal paper Width 5 5 0 5mm Outer Diameter 80mm max Inner Diameter 13mm min Thickness 0 06 0 08mm 1 3 Printing Font e ANK Character set 12x24 dots 1 5 CW x3
3. OSCAR POS58 Line Thermal Printer User s Manual VER1 03 SPRT Introduction Content Chapter 1 Characteristic and SpecificationN 1 1 Printing specification 1 2 Printing Paper 1 3 Printing Font 1 4 Interface 1 5 Printing Control Command i 1 6 Power Supply 1 7 Operation Environment 1 8 Outline Dimension Chapter 2 Installation and Operation 2 1 Printer Appearance 2 2 Paper Installation 2 3 Interface Connection 2 3 1 Parallel Interface CONNECTION cc cceccccccescccccececcccceccccauecceeeas 2 3 2 RS232 Interface Connection 2 3 3 USB Interface 2 3 4 Bluetooth Interface 2 3 5 Cash Drawer Interface 2 3 6 Power Connection 2 4 Buttons and Indicators 2 4 1 Power switch 2 4 2 Feed Button 2 4 3 Opening Upper Cover Button i 1 2 4 4 Power indicator light QFCen i 1 2 4 5 Status Indicator light and Buzzer i 1 2 5 Self test 2 6 Hexadecimal Dump 2 7 Upgrade Mode Chapter 3 Printing Driver Installation 1 Appendix 1 Performance INDEX iii 1
4. SPRT The pin assignment of the cash drawer interface Is as follows Signal Chassis Ground Pe Cash drawer driver signal Out Cash drawer on off status signal 12V DC Out N C i Cash drawer on off status signal ground 2 3 6 Power Connection POS58 uses external power supply as 12VDC 10 2A one core model as below 2 4 Buttons and Indicators 2 4 1 Power switch Control on off status of power IZ is off status Press is on status 2 4 2 Feed Button FEED is paper feed button Print command can enable or disable FEED status to be on or off Under enable status hold down FEED start paper feeding release the button paper feeding stops 2 4 3 Opening Upper Cover Button Hold down opening upper cover button to open the case cover 2 4 4 Power indicator light green If the power is on the power indicator light will be on 2 4 5 Status Indicator light and Buzzer During normal working red STATUS light is off If the working status is 1 0 SPRT abnormal the red indicator light will flicker to alarm error Setting Buzzer can also alarm the abnormal working status Off Off Normal Flicker 1 time and stay Alarm 1 time Paper out and waiting for 1s off and stay 1s loading paper Alarm 2 times Print head is overheated and Flicker 2 times and a and stay 1s just waiting for back to normal Stay 1s off temperature Flicker 3 times and Alarm 3 times Thermal print head damaged stay 1s o
5. 00 H mm e GB2312 80 Chinese 24x24 dots 3 00 W x3 00 H mm 1 4 Interface e RS232 interface DB25 socket female supports XON XOFF and RTS CTS protocol Baud rate 1200 115200bps adjustable Data structure one start bit 7 or 8 data bits one stop bit e Parallel interface DB25 socket male 8 bit parallel interface supports BUSY ACK handshaking protocol TTL SPRT e USB interface standard B type USB interface e Bluetooth interface Support Bluetooth2 0 Bluetooth4 0 Single mode BLE e Cash drawer control DC12V 1A 6 pin RJ 11 socket 1 5 Printing Control Command e Character print command supports double width and double height printing of ANK characters user defined characters and Chinese characters the character line spacing is adjustable e Graphics print command supports the printing of bit map graphics with different density e GS bar code print command supports UPC A UPC E EAN 13 EAN 8 CODE39 ITF25 CODABAR CODE93 CODE128 bar code print 1 6 Power Supply e DC12V 10 2A one core 2A 1 7 Operation Environment e Operation environment temperature 0 50C Relative humidity 10 80 e Storage temperature 20 60 C Relative humidity 10 90 1 8 Outline Dimension e 138 CW x200x L x120 H mm SPRT Chapter 2 Installation and Operation 2 1 Printer Appearance Paper Roller Upper Cover Printer body Power Indicator Status Indicator Paper Case Feed Button
6. 3 00 H mm SPRT RS232 interface DB25 socket female supports XON XOFF and RTS CTS protocol Baud rate 1200 115200bps optional Data structure 1 start bit 8 data bits 1 stop bit Parity optional Parallel interface DB25 socket male or 36pins 8 bit parallel interface BUSY ACK handshaking protocol TTL signal level Cash drawer control DC12V 10 1A 6 pin RJ 11 socket Power Supply DC12V 10 2A A 1009 3P socket Operation Environment Operation temperature 5 50 C Relative humidity 10 80 Storage temperature 20 60 C Relative humidity 10 90C Warning This is a class A product In the domestic environment this product may cause radio interference in which case the user may be required to take adaptable measures
7. e mode are set to 9600bps 8 data bits no parity bit and 1 stop bit The serial interface of POS58 can be connected with standard RS 232C interface When connected to IBM PC or compatible machine connection can accord to the below SPRT pane Serial interface of IBMPC printer SSOP AE epr E Rae Zapin socket 25pin socket DB 25 Fig Connection between POS58S and IBM PC Serial Interface 2 3 3 USB Interface standard B type USB interface 2 3 4 Bluetooth Interface The handheld terminal notebook or other terminals with Bluetooth can drive the printer through Bluetooth interface POS58 printer can support Bluetooth2 0 Bluetooth4 0 Single mode BLE principles Power rate is CLASS2 Valid distance is 10m Device name is POSS8IV initial password is 1234 Device name and password can also be set and changed by Setting Tool Before printing POS58 printer needs to pair with the host firstly The pairing process is as below 1 Turn on the printer 2 The host searches the Bluetooth devices 3 If several Bluetooth devices are found pls choose POSS58IV printer 4 Input password 1234 5 Complete pairing During pairing the printer must be on Note If the device name is not changed during pairing pls do not turn on several printers at the same time Otherwise it will be difficult to identify the one printer paired 2 3 5 Cash Drawer Interface The cash drawer interface of POS58 is RJ 11 6pin socket as below
8. ff and stay 1s needs to repair 2 5 Self test The self test can check the condition of printer In the self test software version interface type characters etc will be printed If the printer prints out the self test receipt correctly it means the printer works normally except the interface with host Otherwise it needs to repair Method of self test Holding down FEED button and turn on the power the red indicator light will flicker at 1 time s within 3 times then release the button self test begins automatically If the self test receipt can be printed correctly it means except the interface the other parts of printer are all well 2 6 Hexadecimal Dump Holding down FEED button and turn on the power the red indicator light will flicker at 1 time s after 3 times then release the button the red light will go on flicker 3 times then the printer will print out 3 lines information as bellow Hexadecimal Dump To terminate hexadecimal dump Press FEED button three times Under this mode all the input will print out as Hexadecimal data Put the FEED button will feed one line each time 3 times together will print out as bellow Completed Then quit the Hexadecimal Dump print mode 2 7 Upgrade Mode Holding down FEED button and turn on the power the red indicator light will flicker at 1 time s after 3 times then release the button The printer enters into Mode Choosing Status Then press LF button 5 times a
9. nd the 11 SPRT time distance between two times must be within 3s The indicator will flicker at 1s on and 1s off status At this time the printer enters into Upgrade Mode Chapter 3 Printing Driver Installation Printing driver for POS58 can be downloaded from the company of our website After downloading the name of driver software is DRV211 During installing driver software choose printer model 58 thermal series About other operation pls refer to the detailed installation manual Appendix 1 Performance Index Print method Direct thermal Print width 57 5 0 5mm Valid print width 48mm Print density 8 dots mm 384 dots line Print speed approx 75mm sec The valid printed content of each line doesn t exceed 25 Reliability Print head life 100km Using condition Print 12 x 24 ASCII characters print 50 lines each time intermittent print repeatedly Each dot line printing at the same time should not exceed 25 each character line and one dot vertical printing repeatedly should not exceed 11 times Use specified thermal paper Thermal paper roll model TF50KS E Japan paper co ltd AF50KS E JUJO THERMAL Thermal paper roll Width 57 5 0 5mm Outer Diameter 80mm max Inner Diameter 13mm min Thickness 58 60g m2 Print Font IBM Character set Il ANK 12x24 dots 1 5 W x3 00 H mm GB GB2312 80 Chinese 24x24 dots 3 00 W x
10. paper is end N PE Pulling up to HIGH level signal SEL by a resistor indicates the printer is online 1 Q3 Pulling up to HIGH level signal by a resistor indicates there is no error 15 ERR 14 16 17 19 NC 18 20 25 GND a Grounding logical 0 level Note 1 In denotes inputting to the printer Out denotes outputting from the printer 2 Signal level is TTL standard Fig Pin Assignment of Parallel Interface 2 3 2 RS232 Interface Connection The RS232 interface of POS58 printer is compatible with RS232C standard SPRT supports RTS CTS and XON XOFF handshaking protocol it uses DB25 socket female the pin order of the RS232 port is as below l 3 oog0g0g000gC0c00 Di 14 Fig Pin Order of the Serial Port The pin assignment of RS232 interface is shown as below 2 R Host Printer receives data from host Printer Printer transmits control code X ON X OFF and data to host R D 3 T receiving data TS Printer Signal MARK indicates that the printer is BUSY and unable to receive data SPACE indicates that the printer is READY for SR printer When this signal is SPACE it means the printer online GND Signal Ground Same with signal CTS Fig Pin Assignment of Serial Interface O7 8 Note Source denotes the source that signal comes from 2 Logical signal level is EIA The baud rate and data structure in RS232 interfac
Download Pdf Manuals
Related Search