Operating Manual
Contents
1. Fig 1 A 4486 Rear Panel Connections 1 24V DC connector 2 1mm DC jack centre pin positive 2 RJ45 connector For connection back to the A 4487 Either port can be used 3 DIP switch options These switches set the chime options 4 BGM Background Music Input The background music can be connected via a 3 5mm Stereo Jack 5 BGM volume Use this volume to adjust the background music level 6 Chime volume Use this volume to adjust the chime level 7 Microphone volume Use this volume to adjust the microphone level DIP Switch Settings DIP switches on the rear of the unit set the Pre announcement chime options See Fig 2 DIP switch 1 sets the pre announcement chime on or off DIP Switches 1 4 Settings DIP switch 2 Not used Off DIP switch 3 Not used Pre announce Chime OnPre announce Chime Off Switch d 2 Not used DIP Switch 4 Not use Not used Not used Fig 2 IMPORTANT NOTE Ensure power is switched off when adjusting DIP switches New settings will be effective when power is switched back on 2 Redback Proudly Made In Australia www altronics com au Paging Console Connecting the A 4486 and A 4487 The Microphone and Line out box are connected by a CAT5e cable with a maximum run distance of 300 metres This CAT5e cable can be connected to either of the two RJ45 ports provided on the rear of the microphone A 24V DC power supply rated at a minimum of 500mA is required to power the system Power connection ca2. www altronics com au Operating Manual A 4486 Paging Console A 4487 Line Out Box N OVERVIEW The A 4486 paging microphone is a simple to use and elegant desk top design which provides paging to a single zone A pre announcement chime is available at the paging console and through the PA system Both of these are set by DIP switches on the rear of the unit Provision has also been made on the rear of the unit for a 3 5mm BGM input for back ground music The A 4487 Line out box provides a Microphone or Line level output which can be connected directly to the input of an amplifier Connection between the A 4486 and A 4487 is via a Cat5e cable which carries power and the balanced audio output from the microphone Power for the system can be connected at the microphone or the Line Out box Features e Single zone paging e High level balanced output via Cat 5 cable e 3 5mm BGM input on rear e 24V DC power supplied via Cat 5 cable e Pre announcement chime e Chime volume adjustment e Mic volume adjustment e BGM volume adjustment Distributed by Altronic Distributors Pty Ltd Phone 1300 780 999 Fax 1300 790 999 Internet www altronics com au Redback Proudly Made In Australia User manual revision number 1 1 20 02 2015 Paging Console DIP Switches 1 2 Settings WI n BGM BGM Chime Mic PA System Chime On PA System Chime Off Internal Chime On Internal Chime Off Input Volume Volume Volume
3. n Hi d REAR OF A 4486 BACKGROUND TO ACTIVATE THE BGM MUSIC SOURCE MOVE THE SWITCH TO THE LOCK ON POSITION Fig 5 SPECIFICATIONS OUTPUT MIC LEVEL ce cccccc cece maniaran ainan 3mV OUTPUT LINE LEVEC csi ccicutnntd saauiadiaaebedhatinnauh dada boaueeteles 1V BGM INPUT SENSITIVITY nescie cece eee eeeee eens 500mV OUTPUT CONNECTORS Audio Outputs A 4487 0 Euroblock terminal Paging Console A 4486 ccceee RJ45 8P8C INPUT CONNECTORS Line Out Box INPUt cee eens RJ45 8P8C 24V DC Power A 4487 Euroblock terminal 24V DC Power A 4486 2 1mm JACK centre ve CONTROLS Mi VOIUIMG s dita tisastichascdextalerenned ddiae Rear Volume Chime Volume cccccceeeeeeceeeeeeeeeeeees Rear Volume BGM VOlUM Sis isnintidascaetvadeidaseedcntadacnes Rear Volume POWER SUPPLEY si cs citccossadccsdactscaletsiniabtieass 24V DC 0 5 Amp DIMENSIONS Z ni A 4486 117W x 135D x 350H DIMENSIONS Z ni A 4487 90W x 52D x 30H WEIGH Seea arae aA A 4486 0 7 kg 4 Redback Proudly Made In Australia www altronics com au
4. installing ensure all connections are verified with a LAN cable tester before switching any system component on Failure to follow the correct wiring configuration may result in damage to system components and will Void the warranty TX TX 586A ane 2m Straight Through a ae both ends 2 6 RX 6 RX Pins Face Upwards 7 7 8 8 Fig 4 www altronics com au Redback Proudly Made In Australia 3 Paging Console Activating the BGM Background Music Backgound music can be supplied to the paging system by connecting an audio source such as a mobile phone tablet etc to the 3 5mm input jack on the rear of the paging microphone Figure 5 shows the position of this connector To activate the background music move the push to talk switch to the up position which is lablelled Lock On While the switch is in this position and only this position will the background music will be piped out The volume is adjusted by the BGM volume trimpot on the rear of the microphone If the switch is moved to the Page position the background music will stop and paging will be active If the switch is in the centre position the BGM and paging are not active Connecting an audio source to the BGM input ADJUST THE BACKGROUND 2 A4486 Communicator MUSIC VOLUME System Busy a zagen f a aa
5. n be made at the microphone itself via a 2 1mm DC Jack or by connecting power to the Line Out Box via a 2 way screw terminal Power is then fed through the CAT5e cable to feed the system from either end If powering the system at the A 4486 end we recommend fitting the power supply with the Altronics P 0602 2 1mm DC Plug with collar which can be screwed onto the DC socket to prevent accidental disconnection of power The balanced audio output from the microphone is transmitted down the CAT5e cable to the Line Out Box which splits and converts the signal to microphone and line level outputs These are provided as screw terminal connections Volume controls for the microphone volume and chime volume are located on the rear of the microphone Typical connection of the A 4486 and A 4487 with a single amplifier 24V DC POWER SUPPLY SUCH AS M 9391A PLUGPACK OR SIMILAR 24V SUPPLY LINE LEVEL SIGNAL TO LINE IN ON AMPLIFIER MIC LEVEL SIGNAL TO MIC IN ON AMPLIFIER CATS cable Max 300M _ NOTE ONLY ONE OUTPUT SHOULD BE USED POWER CAN BE CONNECTED EITHER AT THE A 4486 PAGING MICROPHONE OR AT THE A 4487 LINE OUT BOX 8 T A P P 0602 Fig 3 RJ45 cabling configuration 586A Straight through System components are connected using pin to pin configuration RJ45 data cabling as shown in fig 4 When
Download Pdf Manuals
Related Search