Instruction Manual - Kellyco Metal Detectors
Contents
1. Before you can determine the depth of the detected object you have to scan a further image It only should cover the blue marked area All other metals and mineralized ground should be ig nored because it would disturb the measurement After this you can determine the correct depth 10 3 Regulation of the Number of Impulses There is no special rule for the number of impulses But there are different aspects which has to be considered These are for example e the length of your measured area and e the size of the objects you are searching OKM Ortungstechnik GmbH www okm gmbh de User s manual GEMS 38 The optimal distance between two impulses is about 20cm until 30cm The smaller the distance between two impulses is the more exactly will be the graphical representation If you are looking for small objects you have to select a small distance for big objects you can increase the distance between each impulse Figure 40 shows the effects of the distance and the number of impulses per scan line for some objects bboy ba d tett UL Figure 40 Effect of number of impulses and their distance Figure 41 shows the difference between very few impulses left side and much more impulses on the same scan line length right side The second record right side shows much more details and also smaller objects can be seen Figure 41 Comparison of small and high number of impulses Do not hesitate to record more measurement2. dialog will open like it is represented in figure 11 43 Bluetooth Local COM Vorhandene COM Parts COM COM2 COME COM10 COM11 COM12 COM13 COM14 COM20 COM21 Pat Beschreibung K ommunik ationsanschluss C K ommunik ationsanschluss E Toshiba BT Port COMB Toshiba BT Port COM Toshiba BT Port COM10 Toshiba BT Port COM11 Toshiba BT Port COM1 2 Toshiba BT Port COM13 Toshiba BT Port COM 4 Toshiba BT Port COM 20 Toshiba ET Port COM21 Eigentumer System System LocalCO Mm Clert LocalCOM Server SeralPort T OSHIBA Lo Information Exchanger Information Exchanger Information Exchanger Information Exchanger Information Exchanger HSF Manager HSF Manager Hinzufiugen Loschen Figure 11 Determining the given COM Port There you can find the entry LocalCOM Server SerialPort TOSHIBA LocalCOM which in dicates on which COM Port your Bluetooth Dongle has been installed This COM Port you always have to indicate for the data transmission to the software program OKM Ortungstechnik GmbH www okm gmbh de 6 Installation of Radio Transmission Toshiba 19 6 3 Configurate connection After installation and configuration of your Bluetooth connection you should test if the data transmission from your measuring instrument to the computer is working correctly Be sure that the USB Dongle is attached to your computer Take your measuring instrument and power on the
3. Bluetooth Installation Setup Click now on the button Install to start to copy the files Now wait until the installation is finished and all files has been transferred to your computer OKM Ortungstechnik GmbH www okm gmbh de 7 Installation of Radio Transmission Conceptronic 23 ie BlueSoleil InstallShield Wizard InstallShield Wizard Completed The InstallShield Wizard has successfully installed BlueSoleil Click Finish to exit the wizard Back Gancel Figure 19 Bluetooth Installation Finish As soon as the installation is finished a dialog as in figure 19 appears Click on the button Finish fr BlueSoleil Installer Information You must restart your system For the configuration changes made to BlueSoleil to take effect Click Yes to restart now or No if you plan to restart later Figure 20 Bluetooth Installation Reboot To terminate the installation you have to reboot your computer A message like in figure 20 will appear Confirm it with a click on the button Yes OKM Ortungstechnik GmbH www okm gmbh de User s manual GEMS 24 7 2 Install Bluetooth Dongle After you have reboot the computer the message from figure 21 appears on your screen Now you have to plug in the Bluetooth Dongle into your computer Please insert Bluetooth device 4 ya Le P 17 53 Figure 21 Bluetooth Installation Plug in the Bluetooth Dongle Now your computer tries to install automatically the Bluet
4. secondly there is a chance that the object reacts in an insulted way and strikes back Note the colour of the ground close to the surface A red or reddish color of the ground is an indicator of rust traces As regards the finds themselves you should definitely pay attention to their shape Curved or round objects should be a sign of alarm especially if buttons rings or little pegs can be identified or felt The same applies to recognizable ammunition or bullets and shells Leave that stuff where it is do not touch anything and most importantly do not take any of it home with you The killing machines of war made use of diabolical inventions such as rocker fuses acid fuses and ball fuses Those components have been rusting away in the course of time and the slightest movement may cause parts of them to break and be triggered Even seemingly harmless objects such as cartridges or large ammunition are anything but that Explosives may have become crystalline over time that is sugar like crystals have formed Moving such an object may cause those crystals to produce friction leading to an explosion If you come across such relics mark the place and do not fail to report the find to the police Such objects always pose a danger to the life of hikers walkers farmers or children OKM Ortungstechnik GmbH www okm gmbh de User s manual GEMS 42 13 Maintenance and Services In this section you will learn how to maintain your measuring instr
5. 2 Possible Health Hazards 0 0 0 000 000 2 a eee Qo NN ANC ec oe Be Ge AAA AAA Oe EE le o sta a eee eee Gee eee AA 3 Technical Specifications Gal Sail EEE upep eeg anene wee Date NNN varer ee RE ee wee ew ee A 3 3 Computer Minimum Requirements 0 4 Scope of Delivery 5 Assembly 6 Installation of Radio Transmission Toshiba 6 1 Install Software amp Drivers 2 0 0 0 0 eee ee ee 62 PM e gt s veve cee eevee 6 3 Configurate connection sova ved 2b bo Sed H SG 7 Installation of Radio Transmission Conceptronic 7 1 Install Software amp Drivers 22 r ra rv rv eee eee 7 2 Install Bluetooth Dongle 7 3 Configurate connection e ee 8 Control Elements SL Front View posea a a 6 2 Back VIW o carr AAA 8 3 Touchpad for Menu Navigation 2 00 9 Operating Modes EE ow Gk ee OO OHSS EES NE 9 1 Activate Magnetometer 0 0 0 eee ee ee es JE EE serra Ee REESE EERE DYES Se Ew 9 3 Transfer To PC orcas ea M GEA ek AG 10 Analysis and Evaluation of Measurements 10 1 Metal or Mineralisalion lt 4 6484684 6 Ab aD eee 10 2 General Procedure 0 0000 a ee eae 10 3 Regulation of the Number of Impulses 11 Charging the device 11 1 Front View of the Charger 0 11 2 Charging the Device o 20 we eGR RAE SE Hew GO OKM Ortungstechnik GmbH www okm gmbh de OO CO
6. 22 Bluetooth Installation Setup e 22 Blueto tbh Installation PUSO lt lt sc s6 8ecse ene oh ek be case 23 Bluetooth Installation Reboot 0 0 0 00 ee ee ee aa 23 Bluetooth Installation Plug in the Bluetooth Dongle 24 Bluetooth Installation Set up Bluetooth Dongle 24 Bluetooth Installation Bluetooth Dongle has been installed 24 Find out the assigned COM Port e 25 Find out the assigned COM Port e 25 Find out the assigned COM Port 0 2 ee 26 USB Connection Enter PIN Code 0 vr aar ar aa aa 27 USB Connection Confirm Access arr ra ar aa 27 USB Connection Connection established 27 250 III 28 PAC Vd SoA wea EE EE ee eae ee 29 ode oa ce eee RE eee NE ee 30 Probo OMe osa a oe eee Pe AAA eo GS 32 Graphical Representation Of A Measurement With Horizontal Probe 39 Comparison of object and mineral 35 Givon o EE EE 36 First measurement of an area 2 2 a vr vnr naar aa 37 Control scan Varian ddd we ie ba dbb eee SHES ade ee ee ROH 37 Control stam Vari BS oidos anios aa 37 Effect of number of impulses and their distance 0 0 0084 38 Comparison of small and high number of impulses 38 Front View Charter va aw bh da ee dw ee SPS HRS A 39 Connection OF the OE 40 OKM Ortungstechnik GmbH www okm gmbh de U
7. Of course by selling our products we cannot guarantee that you really make a find during your research The recognition of hidden objects and structures depends on a hugh number of factors like you know Determining factors are the dielectricity constant of the ground the grade of mineralisation and the dimensions of an object relating to its depth Specially in very wet soil clay and sand with high conductivity of the ground recording of the measured results can be falsified strongly With this product you purchased a device which stood the tests in regular operation like all other products of us If you are interested in where our devices have gone into action please visit our homepage For our company it is necessary that we protect our developments within the framework of exist ing legislation to a patent or trademark registration Therewith we offer you a higher warranty while using our products Please take your time consecutively read this user s manual and familiarize yourself with the utilisation and operation of this GEMS OKM Ortungstechnik GmbH www okm gmbh de User s manual GEMS 8 2 Important Notes Please read these operating instructions carefully and closely before using GEMS and its ac cessories These instructions give information on how to use the device and point out potential sources of danger GEMS and its accessories serves for documentation and analysis of detect objects deposited and changes perf
8. appropriate operating mode 9 1 Activate Magnetometer In operating mode Activate Magnetometer the device will activate the integrated magnetome ter mode This mode allows you to notice acoustically the existing field strength The higher the field strength the higher will be the acoustic signal In this operating mode it is easily possible to find metalic objects in particulary iron objects close to the surface 9 2 Ground Scan This operating mode allows you to do a measurement with graphical representation All mea sured data will be stored in the internal memory of the device or sent directly to a connected PC Further information on how to prepare the software programm you can find in the appropriate user s manual Before starting the measurement you have to calibrate the connected probe This procedure is used to adjust the probe to a special area The exacter you execute this procedure the better will be your measurement If you overleap this procedure you should avoid to turn the probe during the following measurement which means the probe should never be turned in another direction during one measurement Three modulators are situated on the upper part of the probe to adjust the sensors like rep resented in figure 33 Hold the probe in your left hand and turn yourself to north direction A number will appear on the display of your device which you should memorize Now turn yourself about 180 degrees so that you look
9. better you can decide afterwards if it is a real object or not Temperature other radio transmission sun energy mineralisation of the ground loam salt water etc can influence negatively the measure results Before you start to dig take your time to do some control scans Repeat exactly the same scan about 3 5 times to be sure about your results Only if all these graphics have almost the same values you can be sure about your results Figure 37 is a graphical representation of a measured area The blue rectangle marks a possible object in the ground To be absolutely sure that there is an object in the ground you have to do a control scan Measure exactly the same area same starting point and the same number of impulses and lines Take also the same distance between the measure points Figure 38 and 39 shows two possible measurements OKM Ortungstechnik GmbH www okm gmbh de 10 Analysis and Evaluation of Measurements 37 Fi E surement of an area Figure 38 Control scan Variant A It is easy to recognize that the control scan in figure 38 is totally different from the first measure ment in figure 37 This means only a mineralisation of the ground not a concrete metalic object Even if the control scan in figure 39 is not exactly the same to the first one you can see that the blue marked parts show nearly the same values This is a reference for the existence of an object Figure 39 Control scan Variant B
10. cue ea cree cree cet cues a aa ewes eens No Maxima Penetration Depth escitas about 8 meters Table 1 Technical Specifications Control Unit 3 2 Data Transmission Tel A Bluetooth Fear Faser ak ees 2 4 2 4835 GHz Maximal Data Transmission Rate cece cent nee n eens 1 Mbps a O o EU on ae EREN 85 dBm Maximal Rante ems ob bete bits a ed od boe id labia bce about 100 meters Table 2 Technical Specifications Data Transmission depends on object size and ground conditions OKM Ortungstechnik GmbH www okm gmbh de 3 Technical Specifications 11 3 3 Computer Minimum Requirements The computer is not part of the scope of delivery The indicated values should help you for a correct selection of a suitable computer for analysis of your measured results CORON A A No CES EA minimum 4x COM Port Data Transmission 0cooccccoccconccrnnncrn ner USB ERES ISO aaa minimum 20 MB Working Memory RAM vrake minimum 128 MB E a IESS minimum 64 MB OpenGL kompatible Operating System as 6 655554 45 056455045454095454540no00 0 Windows 98SE Me 2000 XP Table 3 Technical Specifications Computer Minimum Requirements OKM Ortungstechnik GmbH www okm gmbh de User s manual GEMS 12 4 Scope of Delivery In the following section you can find all standard equipment The scope of delivery can be dif ferent in some circumstances because of some optional accessories which should not be included in the basic equipment 1 Co
11. device Select a operating mode which includes the direct data transmission to PC Additional information on direct data transmission to PC you can find in section 9 on page 3l Bluetooth Manager Bluetooth Sicherheit 3 Bluetooth Schlussel PIM Falls das Feld leer bleibt wird die Standard FIN verwendet Gerat anfordern Bluetooth Gerateadresse D 0B6 53 13 50 1 4 Bluetooth Geratename unknown Abbrechen Figure 12 s soon as you confirm your selected operating mode the device will try to get a radio connection to the computer If this connection is successful a message like in figure 12 appears In this dialog you have to enter OKM It is neccessary to write in capital letters OKM Ortungstechnik GmbH www okm gmbh de User s manual GEMS 20 7 Installation of Radio Transmission Conceptronic This section describes the installation of the USB Bluetooth Dongle Consider that the rep resented figures not necessarily agree with the current version of your operating system or the version of your USB installation The instructions in this chapter are only valid for the Conceptronic usb drivers If you are using the Toshiba usb drivers please read chapter 6 7 1 Install Software amp Drivers Now it is time to install the software and driver on your system Therefore you have to insert your Bluetooth CD into the CD ROM drive of your computer If the CD does not start automatically plea
12. in south direction Compare the represented number OKM Ortungstechnik GmbH www okm gmbh de User s manual GEMS 32 Figure 33 Probe Calibration on the display with the number you kept in mind Try to adjust both values from north and south to each other by turning the modulators Repeat the same procedure also for east and west direction To start a measurement you have to navigate through some submenus At first you have to select the length of the measured field 5m 10m 50m If you want to scan a length of 8m for example you have to select either 5m or 10m in the menu At the selection of 5m the measurement will be less precisely than at 10m In the last step you specify what should be done with the recorded measured values e Store amp Send The measured data will be sent directly to a pc and additionally stored in the internal memory e Store only The measured data will only be stored in the internal memory of the device Go to your start position and power on the device Confirm the operating mode by pressing the key Activate operating mode After you finished the calibration and all other adjustments press the Start Button While the device is now sending out impulses you have to walk even your first measure line step by step When all impulses are sent out the device stops Go to the start of the next measured line which always has to be on the left side from the measured line before and press aga
13. is established Now you have set up successfully your Bluetooth connection OKM Ortungstechnik GmbH www okm gmbh de User s manual GEMS 28 8 Control Elements In this section you will learn more about the fundamental use of all control elements for this measuring instrument All connections inputs and outputs are explained in detail 8 1 Front View Figure 30 shows the front side of the control unit Power On and Off Button Start Button Input for Charger Figure 30 Front View The Power On and Off Button is used to switch on and off the control unit Before operating the device you have to control if the internal battery is charged fully The Start Button is used to start your measurement and to release manually every impulse in the appropriate mode The Input for Charger is used to connect the charger to the main unit It is used to charge the internal battery of the device OKM Ortungstechnik GmbH www okm gmbh de 8 Control Elements 29 8 2 Back View Figure 31 shows the back side of the control unit with all connections Connection Antenna for of Probe Bluetooth Connection of Headphones Figure 31 Back View In the Connection of Probe the cable of the probe has to be plugged in In the Connection of Headphones the delivered headphones has to be connected to the device The Antenna for Bluetooth is used for the data transmission to PC OKM Ortungstechnik GmbH www okm gmbh de User s ma
14. o ox 10 10 10 11 12 14 15 15 18 19 20 20 24 21 28 28 29 30 31 31 31 33 34 34 36 37 User s manual GEMS 12 Danger of Explosion during Excavation 13 Maintenance and Services OKM Ortungstechnik GmbH www okm gmbh de Al 42 List of Figures 5 List of Figures O 0 JO OCA WNW FR A A BWW A A a A www A NN NN NN Ww WWW WW DN FF FF FF FF KF FH wW N HO OOOO UR ONO OO0o0o JO 00430 NPOOOOO Nowvwvb Wn re Oo eo Delivery o se so samer ea sekaa giaa d aro epa 13 Connection antenna and headphones a es 14 Connection of charger and USB dongle at pc 14 Bluetooth Installation a aoao aaa 84 woe dee ee ee we ew 15 Bluetooth Installation Select Language ooa 0000 ee eae 15 Bluetooth Installation Stat s e ssas een eed be ee OGY oO SRDS G 16 Bluetooth Installation Licence Agreement 00 0000 eae 16 Bluetooth Installation Setup 2 ceed ee Nr dat he cues 17 Bluetooth Installation Finish be eee AT 17 Bluetooth Installation Reboot e 18 Determining the given COM Port 222 aa 2 rv rn eee ee aa 18 AE 19 Bluetooth Installation coco awe w ed wide nadan eos 20 Bluetooth Installation Select Language rv vr rn nr eae 20 Bluetooth Installation Start e o 21 Bluetooth Installation Licence Agreement 21 Bluetooth Installation Destination Folder
15. Future Series GEMS User s manual User s manual GEMS 2 Any information contained in these operating instructions may be changed without prior notice OKM does not make any warranty for this document This also applies without limitation to implied assurances of merchantability and fitness for a specific purpose OKM does not assume any responsability for errors in this manual or for any incidental or consequential damage or loss associated with the delivery exploitation or usage of this material This documentation is available as presented and without any kind of warranty In no circumstances OKM takes responsibility for lost profits usage or data losts interruption of business activities or all kind of other indirectly damages which developed because of errors in this documentation This instruction manual and all other stored media which are delivered with this package should only be used for this product Program copies are allowed only for security and savety purposes The resale of these programs in original or changed form is absolutely forbitten This manual may not be copied duplicated or translated into another language neither in part nor completely over the copyright matters without the prior written consent of OKM Copyright 2002 2006 OKM Ortungstechnik GmbH All rights reserved OKM Ortungstechnik GmbH www okm gmbh de Contents Contents 1 Preface 2 Important Notes EE EJA IIA 2
16. all to start to copy the files Afterwards you will be refered that the installation process can take about 15 minutes Answer this question with a click on OK If you did not connect the Bluetooth Dongle until now you will be asked to do so during the installation of the driver Now wait until the installation is finished and all files has been trans ferred to your computer 2 Bluetooth Stack for Windows by Toshiba InstallShield Wizard InstallShield Wizard Completed The InstallShield Wizard has successfully installed Bluetooth Stack for Windows by Toshiba Click Finish to exit the wizard Figure 9 Bluetooth Installation Finish s soon as the installation is finished a dialog as in figure 9 appears Click on the button Finish OKM Ortungstechnik GmbH www okm gmbh de User s manual GEMS 2 Bluetooth Stack for Windows by Toshiba Installer You must restart your system For the configuration changes made to Bluetooth Stack For Windows by Toshiba to take effect Click Yes to restart now or No if vol plan to restart later 18 Figure 10 Bluetooth Installation Reboot To terminate the installation you have to reboot your computer message like in figure 10 will appear Confirm it with a click on the button Yes 6 2 Software Configuration To find out on which COM Port your Bluetooth connection is been installed click on Start Settings Control Panel Double click the entry Bluetooth Local COM
17. all Bluetooth Stack For Windows by Toshiba on your computer To continue click Next Back Cancel Figure 6 Bluetooth Installation Start Now simply click on Nezt to continue the installation A dialog like in figure 7 appears on your screen fr Bluetooth Stack for Windows by Toshiba InstallShield Wizard License Agreement Please read the following license agreement carefully TOSHIBA CORPORATION End User License Agreement This End User License Agreement EULA is a legal agreement between you and TOSHIBA CORPORATION TOSHIBA wath regard to the copyrighted Software provided with this EULA fe I accept the terms in the license agreement I do not accept the terms in the license agreement Installshield lt Back Cancel Figure 7 Bluetooth Installation Licence Agreement Select the option I accept the terms in the licence agreement and confirm it with a click on Next OKM Ortungstechnik GmbH www okm gmbh de 6 Installation of Radio Transmission Toshiba 17 2 Bluetooth Stack for Windows by Toshiba InstallShield Wizard Ready to Install the Program The wizard is ready to begin installation Click Install to begin the installation IF vou want to review or change any of your installation settings click Back Click Cancel to exit the wizard Installshield lt Back Install Cancel Figure 8 Bluetooth Installation Setup Click now on the button Inst
18. an find in the manual of your software product Immediately after confirming the operating mode by pressing the key Activate operating mode the message Connecting with Computer will appear on the display of your device This pro cedure can take a few seconds Further information about the connection establishment via Bluetooth you can find in section on page Afterwards you will be asked to press the Start button The measured data will now be transmitted to your computer at one time OKM Ortungstechnik GmbH www okm gmbh de User s manual GEMS 34 10 Analysis and Evaluation of Measurements Before measurement you have to know what kind of objects or cavities you are looking for and if the area you choose is suitable for this Measurement without a plan will not give you the results you would like For this reason please consider the following indications e What are you looking for graves tunnels buried objects This question has its effects on your concrete manner to measure an area If you are looking for big objects you can enlarge your distance between the measure points impulses for small objects use small distances see section 10 3 on page 37 e Inform yourself about the area you select for measurement Is it usefull to search at this place Are there historical indications which confirm your speculations What type of soil is on this area Are there good conditions for data recording e Your fi
19. ation e Depth With a small depth of about 0 10m or 0 40m there is a high possibility that there is only a mineralisation of the ground OKM Ortungstechnik GmbH www okm gmbh de 10 Analysis and Evaluation of Measurements 35 e Color Filter If position and form of the object are changing with the use of the color filter it is probably a mineralisation e Control Scan If position depth and form of the object stay nearly the same also in further control scans you can conclude of a real object Also if some graphics look similiar you always have to compare all indications Figure 35 shows a real object left side and a mineralized accumulation right Figure 35 Comparison of object and mineral OKM Ortungstechnik GmbH www okm gmbh de User s manual GEMS 36 10 2 General Procedure The main rule for scanning an area is The more exactly you scan an area the better will be your graphical evaluation You have to scan in a given manner that the software can calculate the measured values in the right way Your device has following possibilities e Zig Zag e Parallel Figure 36 shows all different ways of scanning in a scheme The measurement starts at your starting point O and ends at point Figure 36 Given manner If you have finished one scan line the next line has to be on the left side Do not change the direction of your probe The more you repeat your scanning above a possible object control scans the
20. direct data transmission to PC Additional information on direct data transmission to PC you can find in section 9 on page 31 Enter Bluetooth Passkey X gt remote device needs a Bluetooth Passkey to create Paired se relationship for future connections Please use the same passkey on this device and on the remote device Cancel Remote Device Address 00 08 53 13 81 66 Passkey E Time Left 18 2 Figure 27 USB Connection Enter PIN Code As soon as you confirm your selected operating mode the device will try to get a radio connection to the computer If this connection is successful a message like in figure 27 appears In this dialog you have to enter OKM It is neccessary to write in capital letters Confirm this entry by a click on the button OK Bluetooth Service Authorization X a Bluetooth device 00 0B6 53 13 81 6B is attempting to access Bluetooth Serial Port service Click Tes to allow this device to access this service 7 a e Always allow this device to access this service Time Left 22 Figure 28 USB Connection Confirm Access Another window will open where you mark the entry Allways allow this device to access this service and confirm this entry by a click on Yes Remote Device O0 08 53 13 317 66 has connected to mp Serial Port A COM 7 service cc sa Y O 17 53 Figure 29 USB Connection Connection established The message from figure 29 indicates that the connection
21. ed Also you have to remove keys telephones chains and rings and all other magnetic and metallic objects from yourself OKM Ortungstechnik GmbH www okm gmbh de 2 Important Notes 9 2 4 Voltage The power supply should not be outside the indicated range of values Use only chargers bat teries and rechargable batteries which are included in the scope of delivery Never use the 230 Volt mains supply 2 5 Data safety There can be errors in the process of data collection if e the range of the sender module is been exceeded e the power supply of the device is to low the cables you are using are to long other electronic devices sends out disturbances or atmospherics occurs lightnings OKM Ortungstechnik GmbH www okm gmbh de User s manual GEMS 10 3 Technical Specifications The following technical indications are medial values During operation small variations are quite possible 3 1 Control Unit Dimensions Hx Wx DD ene rsrsrsr 170mm x 90mm x 35mm e eo arden eure axons ere eee eee about 0 35 kg VOLTS on pedusedeucvecedaueveuuvepuendscetedededadsteasdadedadadaededanedes 9 12 VDC PROCESOS pen we re EAE EE PERE EEE ERE EEE EEE EIDE OREO PERE Motorola 32 MHz Data Memory internal 45 09 45 0945 05450095 4 000 044s09 eon9 a eye ne 65 500 measured values Operating Temperature 0 eee e ene enn t nee nanee 0C 50 C TANN eee 20 C 60 C NNN SS 5 75 VINNE evaporar nea re e cuss cues
22. in the Start Button Repeat this procedure until you scanned the whole area you want to measure In your software programm there will appear a graphical representation of this area like you can see in figure 34 The graphic should include prevalent green color values which represent the normal ground Therein could be visible red and blue objects Metallic objects will mostly be represented in red color and cavities water and excavations in blue color Beware that mineralisations of the OKM Ortungstechnik GmbH www okm gmbh de 9 Operating Modes 33 Figure 34 Graphical Representation Of A Measurement With Horizontal Probe ground will also be represented in red color How to discriminate between mineralized rocks or soils and real metals you can read in section 10 1 on page 34 or in the user s manual for your software program Please read attentively section 10 2 on page 36 where the procedure of a graphical measurement is explained in detail 9 3 Transfer To PC With operating mode Transfer to PC measured values can be transmitted from the internal memory of the device to a computer Therefore it is necessary that the software has to be prepared before starting the transmission Only if all preparations of the software are made correctly and the software program is ready to receive the measured data you can confirm this function Further information about a correct preparation of the software program you c
23. ing the time of discharging OKM Ortungstechnik GmbH www okm gmbh de User s manual GEMS 40 11 2 Charging the Device To load the GEMS the delivered charger has to be connected with the control unit in the provided input like represented in figure 43 Figure 43 Connection of the Charger During the loading time the Control Lamp B is shining red As soon as the complete charg ing is finished the Control Lamp B change to green color It is recommended to discharge the GEMS completely after about 5 charging procedures and reload it afterwards By pressing the Button to Discharge the internal batteries of the device will be discharged completely and afterwards reloaded automatically During the time of discharging the Control Lamp for Discharging is shining yellow The discharging and charging procedure should not be intermitted unnecessarily Only if the Control Lamp B is shining in green color the charging procedure is finished OKM Ortungstechnik GmbH www okm gmbh de 12 Danger of Explosion during Excavation 41 12 Danger of Explosion during Excavation Unfortunately the last two world wars also made the ground in many places of the world a potentially explosive scrap heap A host of those lethal relics are still buried in the ground Do not start digging and hacking for an object wildly when you receive a signal of a piece of metal from your device Firstly you might indeed cause irreparable damage to a truly rare find and
24. ntrol Unit 1 Probe 1 Charger for Control Unit 1 USB Bluetooth Dongle 1 USB Setup CD 1 3D Software Visualizer 3D 1 Headphones 1 Manual 1 Carrying Case Table 4 Scope of Delivery Beware that pictures in this manual could be different to delivered parts OKM Ortungstechnik GmbH www okm gmbh de 4 Scope of Delivery 13 Control Unit EN 1 ox OKM USB Bluetooth Dongle Headphones Charger for Control Unit Figure 1 Scope of Delivery OKM Ortungstechnik GmbH www okm gmbh de User s manual GEMS 14 5 Assembly In this section is explained how to assemble the device and how to prepare a measurement Figure 2 Connection antenna and headphones In figure 2 you can see how to assemble the antenna Do it without any unnecessary application of force Also it is visible where to connect the headphones Figure 3 Connection of charger and USB dongle at pc Figure 3 shows how to connect the delivered charger to the main unit Also you can see how to connect the bluetooth dongle with the USB port of your computer Further information of the correct use and installation of the USB driver you can find in section on page OKM Ortungstechnik GmbH www okm gmbh de 6 Installation of Radio Transmission Toshiba 15 6 Installation of Radio Transmission Toshiba This section describes the installation of the USB Bluetooth Dongle Consider that the rep resented figure
25. nual GEMS 30 8 3 Touchpad for Menu Navigation The top of the device is including a touchpad like in figure 32 With this touchpad you can navigate to the different operating modes in the menu LCD Display Activate Operating Mode Previous Operating Mode Next Operating Mode Figure 32 Touchpad With keys and you can select every operating mode To confirm your selection press ok OKM Ortungstechnik GmbH www okm gmbh de 9 Operating Modes 31 9 Operating Modes In this section you will learn more about the different operating modes of the device Every function is been explained in particulary in its proper subsection The right selection of an op erating mode depends primarily of your planned measurement So for example there are some special functions which have to be used for a first measurement in a unknown area to get a general overview against which others are more suitable for a detailed search and analysis with a special processing software program The device prossesses the following operating modes e Sound Mode Activate Magnetometer e Ground Scan Send measured values directly to a pc for analysis or store measured data in the internal memory of the device to get a graphical representation of the measured area e Transfer To PC Send measured values stored in the internal memory of the device to a PC for analysis Via a touchpad on the top of your device you can select and confirm your
26. ooth Dongle Wait until a dialog window like in figure 22 appears on your screen Click on the button OK Welcome to Bluetooth xX Welcome to Bluetooth General _ __________ Please set your Bluetooth device name and device type This information will be shown to other Bluetooth devices Device Address 00 80 54 46 17 82 Device Name Device Type Desktop n 5 ecu ao Tou security level is Medium now Other Bluetooth devices P must provide a Bluetooth passkey before connecting with your computer If you do not want to have security authentication uncheck Use security level Medium M Use security level Medium Figure 22 Bluetooth Installation Set up Bluetooth Dongle After a successful set up of the Bluetooth Dongle the message from figure 23 appears on your screen Bluetooth started ya e P 17 53 Figure 23 Bluetooth Installation Bluetooth Dongle has been installed OKM Ortungstechnik GmbH www okm gmbh de 7 Installation of Radio Transmission Conceptronic 25 To find out on which COM Port the Bluetooth connection has been installed you have to click with the right mouse button on the Bluetooth symbol in the task bar A dialog window like in figure 24 will appear Exit v Show Messages Display Figure 24 Find out the assigned COM Port If you click here on the entry Display a window like represented in figure 25 will open Select in the menu View the option Ser
27. ormed in the ground The registered data of the ground structure will be transmitted to a PC for visual representation in a special software program using the components we offer Any additional notes relating to this has to be observed Please read attentively the manual according to the software you are using 2 1 General Notes Being an electronic device GEMS has to be treated with the caution and care necessary when such devices are used Any failure to observe the safety precautions given or any use for purposes other than the ones it is conceived for may result in a damage or destruction of the processing unit and connected components The device will get destroyed if it is opened improperly 2 2 Possible Health Hazards If used properly the device normally does not pose any health hazards According to current scientific knowledge the high frequency signals are not harmful to the human body on account of their low power 2 3 Surrounding Area Having been transferred from a cold to a warmer place the device should not be operated im mediately afterwards Any condensation which may have formed might cause the device to get destroyed Avoid strong magnetic fields which may occur in places such as near machines or loudspeakers and avoid using a detector within a radius of 50 meters Metallic objects on the ground such as cans doses catches nails screw or others can influence negatively your measurement and have to be remov
28. rs on your screen 2 BlueSoleil InstallShield Wizard License Agreement Please read the Following license agreement carefully N Bluesoleil End User License Agreement NOTICE TO USER PLEASE READ THIS AGREEMENT CAREFULLY THE BLUESOLEIL END USER LICENSE AGREEMENT AGREEMENT IS VALID AND BINDING AGREEMENT BETWEEN YOU As A USER AND PVT CORPORATION IVT BY USING ALL OR ANY PORTION OF THE SOFTWARE YOU ACCEPT ALL THE TERMS AND CONDITIONS Pa o FIL ele e om d A AT TTT TTL T TIT T TTT TIT TLT ao AMO T AT TT AAA fe I accept the terms in the license agreement Print I do not accept the terms in the license agreement Installshield lt Back Cancel Figure 16 Bluetooth Installation Licence Agreement Select the option I accept the terms in the licence agreement and confirm it with a click on Next OKM Ortungstechnik GmbH www okm gmbh de User s manual GEMS 22 3 BlueSoleil InstallShield Wizard Destination Folder Click Next to install to this Folder or click Change to install to a different folder Installshield Figure 17 Bluetooth Installation Destination Folder Inside the dialog from figure 17 you have the possibility to select another destination folder Normally there is no changing necessary Click only on the button Next 8 BlueSoleil InstallShield Wizard Ready to Install the Program The wizard is ready to begin installation Installshield Figure 18
29. rst measurement in a unknown area has to be large enough to get representative values f ex 20 impulses 20 search lines e What is the form of the object you search If you are looking for an angular metal box the identified object in your graphic should have a form according to this e To get exact values concerning the depth measurement the object has to be in the centre of the graphic which means it has to be framed by normal reference values normal ground If the object is on the side of the graphic and not totally visible a correct depth measurement is not possible e There should not be more than one object in a graphic This will influence the exactness of depth measurement e You should do at least two control scans to get sure about your results So you also can recognize and isolate mineralized ground see section 10 1 on page 34 10 1 Metal or Mineralisation At the beginning it is not always easy to make a difference between real objects and mineralized ground In principle metals are represented in red color but mineralized accumulations can also include red signals Here some advice how you can differentiate between a real object and a mineralisation e Form If the object represented in your graphic has a special form f ex rectangle circle you can conclude of a possible real found e Color If there are many yellow and orange color values around the object it will be probably a mineralis
30. s not necessarily agree with the current version of your operating system or the version of your USB installation The instructions in this chapter are only valid for the Toshiba usb drivers If you are using the Conceptronic usb drivers please read chapter 7 6 1 Install Software amp Drivers Now it is time to install the software and driver on your system Therefore you have to insert your Bluetooth CD into the CD ROM drive of your computer If the CD does not start auto matically please double click on Desktop and then double click on the symbol of your CD ROM drive With a further double click on file setup exe you start the installation Toshiba Drivers Dual Mode Utility y Flash Disk Tool y CD Explore Exit Figure 4 Bluetooth Installation The first window of your installation will open Click here on the entry Toshiba Driver and follow the instructions on the screen Choose Setup Language xX Select the language for this installation from the choices below Figure 5 Bluetooth Installation Select Language OKM Ortungstechnik GmbH www okm gmbh de User s manual GEMS 16 First there is a possibility to select the language of the installation Click on OK to change to the installation dialog from figure 6 iis Bluetooth Stack for Windows by Toshiba InstallShield Wizard X Welcome to the InstallShield Wizard for Bluetooth Stack tor Windows by Toshiba The InstallShieldiR Wizard will inst
31. s with different numbers of impulses For example you can scan a large area before doing a second detailed precision measurement Especially for the search of bigger objects you can proceed like this With this manner you can measure relatively fast a large area and afterwards you can record the interesting subsection Further information about the graphical analysis you can find in the appropriate software man ual OKM Ortungstechnik GmbH www okm gmbh de 11 Charging the device 39 11 Charging the device In this section you will learn more about how to operate the delivered charger 11 1 Front View of the Charger Figure 42 indicates the front side of the charger and its control elements Connector Button to Discharge Control Control Lamp A Lamp B Charging Charging Panel A Panel B Control Lamp for Discharging Figure 42 Front View Charger Der Connector is used to connect the charger to the control unit With the Button to Discharge the discharge process can be started Control Lamp A and Control Lamp B signalize the charging process of the corresponding charging panel During the time of charging the control lamp will shine red as soon as this procedure is finished it will shine in green color The Charging Panel A can be used to reload a 9V battery The Charging Panel B cannot be used to reload 9V batteries T herefore please use the Charging Panel A The Control Lamp for Discharging is shining yellow dur
32. se double click on Desktop and then double click on the symbol of your CD ROM drive With a further double click on file autorun exe you start the installation Conceptronic Bluetooth 1 Install drivers and application software for Windows S8SE ME 2000 XP Manual 3 Application Note 4 Acrobat Reader 5 Browse this CD p pl E a p B a o E O 3 3 Figure 13 Bluetooth Installation The first window of your installation will open Click here on the entry 1 Install drivers and application software and follow the instructions on the screen Wahlen Sie eine Setup Sprache aus Wahlen Sie die Sprache dieser Installation aus der unten En aufgetuhrten Auswahl aus Abbrechen Figure 14 Bluetooth Installation Select Language OKM Ortungstechnik GmbH www okm gmbh de 7 Installation of Radio Transmission Conceptronic 21 First there is a possibility to select the language of the installation Click on OK to change to the installation dialog from figure 15 7 BlueSoleil InstallShield Wizard x Welcome to the InstallShield Wizard for BlueSoleil The InstallShieldiR Wizard will install BlueSoleil on your computer To continue click Next WARNING This program is protected by copyright law and international treaties Back Cancel Figure 15 Bluetooth Installation Start Now simply click on Next to continue the installation dialog like in figure 16 appea
33. ser s manual GEMS 6 List of Tables Aa wW N e Technical Specifications Control Unit a 02000 10 Technical Specifications Data Transmission rn 10 Technical Specifications Computer Minimum Requirements 11 PCcOpe of Deliyery s sares sano AO Ee wee ak Ro oe YR a we eee 12 OKM Ortungstechnik GmbH www okm gmbh de 1 Preface 7 1 Preface Dear customer in the first instance we want to thank you that you made your decision on a product of OKM Ortungstechnik GmbH With the GEMS you purchased a product which is based on a electromagnetic pulse method which can be used to locate anomalies in the target area Thus the device is able to detect natural features such as formations of strata cavities groundwater level as well as sepulchers or buried objects such as pipes tanks boxes or suchlike The GEMS is able to locate to document and to analyse buried objects with different structures without making necessary any excavation Particularly in areas next to the surface there are many advantages to geoelectric seismic and magnetic procedures and it is further more a usefull complement to these methods The GEMS has a facile and flexible handling and provides fast and easy reproducible results With our team of specialists we guarantee that our products are under recurrent control Our specialists try to implement new developments in terms of further quality improvements for you
34. ument with all included ac cessories to keep it in good condition a long time and to get good measuring results The following list indicates what you absolutely should avoid e penetrating water e strong dirt and dust deposits e hard impacts e strong magnetic fields e high and long lasting heat effect If you want to clean your device please use a dry rag of soft material To avoid any damage you should transport the device and accessories always in the appropriate carrying cases Beware that all batteries and accumulators are always charged fully while operating with your system You should only load the batteries when they are completely discharged no matter if you are working with the external power supply or with the internal accumulators In this way a long durability of the used batteries is guaranteed To load the external and internal batteries you have to use only chargers which are part of our scope of delivery OKM Ortungstechnik GmbH www okm gmbh de Index Activate operating mode 32 33 Bluetooth 15 20 Bluetooth Dongle 24 Button to Discharge 39 40 Charger 28 39 Charging Panel A 39 Charging Panel B 39 Connector 39 Control Lamp A 39 Control Lamp B 39 40 Control Lamp for Discharging 39 40 Dongle 15 20 Start Button 32 Start button 33 USB 15 20 43
35. vice Window IVT Corporation BlueSoleil Main Window Ioj xj File View My Bluetooth My Services Tools Help Main Window Ctrl Tab Service Window Ctrl Tab Arrange Devices Refresh Devices F5 ul Displays Service window Starting service Personal rea Networki PAN IP 0 0 0 0 Figure 25 Find out the assigned COM Port An image like in figure 26 is represented Behind the indication Serial Port A you can read the number of the assigned COM Port In this figure it is COM7 this can be different on your computer OKM Ortungstechnik GmbH www okm gmbh de User s manual GEMS I T Corporation BlueSoleil Service Window i ioj xj File View My Bluetooth My Services Tools Help Personal Area Networking Serial Port COM Serial Port B COMES To Object Push File Transfer Information Synchronization LAN Access AV Headphone Basic Image r Starting service Personal Area Networki PAN IP 0 0 0 0 4 Figure 26 Find out the assigned COM Port OKM Ortungstechnik GmbH www okm gmbh de 26 7 Installation of Radio Transmission Conceptronic 27 7 3 Configurate connection After installation and configuration of your Bluetooth connection you should test if the data transmission from your measuring instrument to the computer is working correctly Be sure that the USB Dongle is attached to your computer Take your measuring instrument and power on the device Select a operating mode which includes the
Download Pdf Manuals
Related Search