ASSEMBLY & USER MANUAL
Contents
1. 11 STEP 10 Adjust the 3 springs Turn the springs has shown GOLDMUND REFERENCE II Assembly Manual 12 STEP 11 Take 4 rubber seals and insert them in one of the 3 holes on the table 4 rubber seals per hole Repeat the operation for both other holes STEP 12 When the seals are positioned place 1 golden insert in the hole Repeat the operation for both other holes GOLDMUND REFERENCE II Assembly Manual 13 STEP 13 For this step you need to be 2 persons One person take carefully the motor block by its basis and keep in above the 3 holes with the golden insert as shown on the picture The other person runs the cables trough the central hole and leave them hanging Then the first person can mount the motor on the table making each black serrated knurl facing its golden insert ATTENTION Please check the motor and the motor black knurl is in the same position as the one shown on the picture GOLDMUND REFERENCE II Assembly Manual 14 STEP 14 Take the tripod and mount it as shown on the left picture The arm with the 4 small holes should be directing towards the rear foot of the turntable ATTENTION Please check the tripod is well positioned GOLDMUND REFERENCE II Assembly Manual 15 STEP 15 Screw but not over tight the tripod to the feet with the 3 screws dismounted at the beginning of the assembly see STEP 4 STEP 16 Remove carefully the axis from the tr2. of the tripod feet STEP 4 Box 3 Tripod Unscrew the tripod from its 3 feet Keep the 3 screws that you will use back at the end of the assembly GOLDMUND REFERENCE II Assembly Manual 7 STEP 5 Box 3 Tripod Free the tripod assembly from the box and set it on 3 temporary supports like foam rubber or books leaving the center free GOLDMUND REFERENCE II Assembly Manual 8 STEP 6 Box 3 Tripod In the box n 3 you will find the 3 cylinder feet of the tripod Please take one cylinder foot to position it at the front left position Be carful to select the foot with the correct basis check the bottom of the foot Repeat the operation for the front right cylinder foot GOLDMUND REFERENCE II Assembly Manual 9 Box 4 Various Parts In the box n 4 you will find 1 platter 1 motor bloc 1 belt 12 rubber seals 1 large golden insert 3 small golden insert 1 clamp 1 small oil bottle STEP 7 Box 4 Various Parts Take the large golden insert STEP 8 Position it in the center of the third cylinder foot position GOLDMUND REFERENCE II Assembly Manual 10 STEP 9 Box 3 the tripod In the box n 3 take the last cylinder foot Check if its design is the same as the one shown on the left picture Position it in the bottom of the third cylinder foot position passing the axe through the hole The 3 cylinder feet are positioned GOLDMUND REFERENCE II Assembly Manual
3. ASSEMBLY amp USER MANUAL GOLDMUND REFERENCE II Turntable Congratulations Thank you for purchasing the GOLDMUND Reference II Turntable You have acquired a highly exclusive and refined limited series product holding a number of new features that have never been experienced before Please take some time to read this manual It will provide you with useful information to make your pleasure of using the Reference II Turntable even higher INTRODUC TION GOLDMUND REFERENCE II Turntable Goldmund was founded in 1978 and has ever since been dedicated to the accurate reproduction of sound and image At Goldmund we strive to lead in the creation development and manufacture of the industry s most advanced technologies including audio and video systems home networking and music distribution The guiding principle at Goldmund is to produce a precise sound with the least possible loss of quality through the different stages Goldmund will never adopt a technology before it is sufficiently developed to satisfy the high quality standards we set This is why Goldmund has often rejected mainstream technologies and developed its own Table of Contents O oF W N UNPACKING CHOICE OF TURNTABLE LOCATION TURNTABLE ASSEMBLY AMPLIFIER CONTROLS USER INSTRUCTIONS CLEANING amp MAINTENANCE 20 21 22 GOLDMUND REFERENCE II Assembly Manual 3 Ww A R N I N G The Goldmund Reference Il you just purchased represents a summ
4. emove the power supply from its box and position it nearby the turntable Then take the connector cable and plug it to the power supply Plug the second extremity to into the turntable right central foot base s socket GOLDMUND REFERENCE II Assembly Manual 19 AMPLIFIER CONTROLS The Goldmund Reference II can be used with most existing ton arms both pivoting and Straight line Up to three tone arms may be assembled on the turntable Even if the Goldmund T8 tone arm is installed two additional pivoting arms may be used Goldmund provides upon request various basis for the most common tone arm lengths available Please consult your Goldmund representative for any further information To assemble the Goldmund T8 tone arm please refer to the tone arm assembly manual GOLDMUND REFERENCE II Assembly Manual 20 D USER INSTRUCTIONS Now your turntable is assembled you can start using it 1 9 9 4 5 6 T Switch on the power supply Unscrew the clamp and remove it very carefully Position the record to play Re mount the clamp carefully tighten it holding its basis Select the speed corresponding to the disc e For 33T press the button 33 e For 45T press the button 45 e For 78T optional Please contact your local Goldmund distributor Position the tone arm on the record To stop the turntable press the button STOP after removing the tone arm We recommend leaving the turntable run for a f
5. ew hours in order to stabilize its performance Note the bottom line of keys is dedicated to the Goldmund T8 tone arm use See separate user manual GOLDMUND REFERENCE II Assembly Manual 21 CLEANING amp MAINTENANCE There is no special maintenance to be done on your turntable Clean with dust free soft cloth Drive wheel and motor pulley may be cleans after months of use or if abnormal speed variation occurs Note Clean with Isopropyl Alcohol only Belt may be changed after heavy use especially if it becomes too hard and does not grip enough on the pulley WARNING Always turn the power off on the power supply before cleaning your turntable All enquires relating to product servicing and operation should be referred to the local authorized retailer supplying and supporting your Goldmund equipment RUNNING IN TIME The Goldmund Reference Il shaft and axis are machined with extreme precision The optimal performance can only be reached after approximately 100 hours of use despite the initial working period of 50 hours processed at the factory GOLDMUND REFERENCE II Assembly Manual 22
6. ipod GOLDMUND REFERENCE II Assembly Manual 16 STEP 17 Add some oil contained in the bottle in the axis shaft IMPORTANT After this step make sure you clean your hands from any oil STEP 18 Reinsert the axis with extreme care into the shaft assembly Make the axis descend extremely slowly STEP 19 Mount the belt around the axis wheel and the motor pulley as shown on the pictures Check that the belt is flat against drive wheel and motor pulley GOLDMUND REFERENCE II Assembly Manual 17 STEP 20 Mount the platter on the center axis This should be done with great care and the platter must be set in position very slowly IMPORTANT The platter shouldn t at any time be dropped or shocked Take great care since the platter is very heavy Note To remove the platter help may be required Platter can be removed by pulling straight up slowly A second person may have to push on the central spindle to ease the process STEP 21 Set the 3 large finish cylinders Adjust height and lower the tripod assembly by turning the large adjustment cylinders Level the tripod assembly using a bubble level Repeat the operation if necessary GOLDMUND REFERENCE II Assembly Manual 18 STEP 22 Put the 3 top cylinders on the tripod STEP 23 Check the level of the table top first then the platter with a bubble level If needed repeat step 21 with the platter positioned STEP 24 Box 5 Please r
7. it in terms of design concept and quality of reproduction Therefore great care should be taken before attempting to put the unit together Read the instruction manual carefully This will eliminate the risk of damage or loss in performance PLEASE READ THE INSTALLATION MANUAL COMPLETELY PRIOR TO INSTALLATION PLEASE DO NOT CONNECT ANY CABLES OR MOVE ANY PART BEFORE READING THE FOLLOWING INSTRUCTIONS OBSERVE GENERAL ELECTRICAL SAFETY PRECAUTIONS PARTICULARY WITH REGARD TO AVOIDING WATER MOISTURE AND HEAT TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THE COVERS AND REFER SERVICING TO QUALIFIED PERSONNEL GOLDMUND REFERENCE II Assembly Manual 4 WARNING PLEASE READ INSTALLATION MANUAL COMPLETELY PRIOR TO INSTALLATION 3 PERSONS ARE NECESSARY TO INSTALL THIS TURNTABLE UNPACKING Your turntable is shipped in 4 separate wood boxes labeled 1 to 4 and 1 carton box labeled 5 Box 1 the base feet assembly Box 2 the table top Box 3 the tripod Box 4 all mechanical parts to be assembled Box 5 the power supply The electronic control box is already assembled under the table top ATTENTION Please keep the packaging in case you need to transport the turntable at a later date or if you have to send it for maintenance This packaging has been designed specifically to protect the Reference II turntable in transit Use of alternative packaging is likely to result in damage invalidating war
8. ranty CHOICE OF TURNTABLE LOCATION Due to the total weight of your turntable 300kg please choose the definitive location of your turntable in order to install it on site Locate the player on a support providing the most rigid possible connection to the floor Solid coupling is essential and if your Support is standing on a suspended floor at least one foot should be located over a supporting beam or close to a supporting wall for an optimal result GOLDMUND REFERENCE II Assembly Manual 5 3 TURNTABLE ASSEMBLY STEP 1 Box 1 the base feet assembly Unscrew and remove the top of the wood box n 1 Remove the protection cover Unscrew and remove a side of the wood box Free the feet base and position it at its definitive location the red bar on the back Note Make sure the small screen is facing toward the front with both central pointes bolt on the back STEP 2 Box 2 the Table top Unscrew and remove the top cover of the wood box n 2 Remove the protection cover Mount the table top on the base with the control panel keyboard facing the front Then unscrew the cover hiding of the electronics cables below the table Free the control panel cables from the base bottom and run all cables through base GOLDMUND REFERENCE II Assembly Manual 6 STEP 3 Box 3 Tripod Unscrew and remove the top cover of the wood box n 3 Remove the protection cover Remove the 3 cylindrical weights sitting on top
Download Pdf Manuals
Related Search