Gen-Eye SD - General Pipe Cleaners
Contents
1. e Check to see if the monitor brightness and contrast controls are turned up e Check the interface cord for possible damage or inter mittent problem by flexing the cable e Check the cable for possible breaks or intermittent open circuits by flexing the cable e Remove the camera from the cable assembly and plug it into the Camera Test Terminal e Disconnect the main power and contact the factory service department Dark Picture e Check to see if the monitor brightness and contrast controls are turned up e Check the Light Head to see if it is not supplying suffi cient light due to weak dirty or burned out bulbs e Check to see if the Light Head intensity control is turned up e Disconnect the main power source and contact the factory service department Bad or Grainy Picture e Check the camera lens for dirt grime scratches or other foreign matter e Check the Light Head to see if it is not supplying suffi cient light due to weak dirty or burned out bulbs e Check for external electrical noise being radiated by outside sources such as a power station etc e Check the cable for possible breaks or intermittent open circuits by flexing the cable e Remove the camera from the cable assembly and plug it into the Camera Test Terminal e Disconnect the main power source and contact the factory service department Not Recording e Always check record and play functions prior to in spections to ensure th2. camera housing is normal and should be of no concern however use the trap skid to protect the camera and help it slide around elbows more easily The camera lens is made of sapphire and should be cleaned with a soft damp cloth Grease dirt or scratches will affect the quality of the video picture LIGHT HEAD REPLACEMENT The light heads for the Gen Eye SD cameras use LED lighting and cannot be replaced by the operator These lights use very little power Unless physically damaged or extreme voltage is applied to them they should last indefinitely If replacement is necessary the camera should be returned to the factory The camera lights are wired in a series parallel configura tion This means that there are 4 sets of 4 color camera each wired together Each set is wired in series and then the 4 sets are wired in parallel Therefore should one lamp burn out in one set the other sets will still remain lit CABLE AND REEL ASSEMBLY CLEANING WHEN CLEANING THE REEL ASSEMBLY DO NOT USE A POWER WASHER WATER MAY GET INTO UNSEALED AREAS SUCH AS THE REEL HUB AS SEMBLY AND SLIP RING HOUSING CAUSING DAM AGE AND VOIDING THE WARRANTY The cable and reel assembly should be kept clean from dirt When rewinding the cable back onto the reel after an inspection it is good practice to use a clean rag to wipe off any debris the cable may have CAMERA REMOVAL FROM THE CABLE AND REEL ASSEMBLY TO PREVENT DAMAGE TO THE CAMERA AND
3. depending on pipe conditions You may also adjust the brightness and contrast controls on the monitor Lighting may be adjusted to highlight various pipe conditions and objects as desired In some cases white or lighter colored objects may cause the picture to flare or wash out If this happens simply turn the light control down until a good picture is achieved Push the camera slowly and carefully during the in spection taking note of the pipe condition for possi ble hazards that may entangle or damage the cam era on entry or retrieval When negotiating a corner care should be taken not to butt the nose of the camera against the sidewall with any force It would be better to let the camera work its way around the corner If resistance is en countered when turning the corner and there is no visible signs of blockage turning the push rod or pull ing the camera back and forth slowly sometimes helps Should resistance become extreme or the camera gets entangled or stuck slowly push back and forth to free it Sometimes turning the push rod may also help If the camera is visible you may be able to free it with your hand or some other means To start the recording process press the REC but ton on the SD Recorder or the SD Recorder remote control To end the recording press the STOP button on the SD Recorder or the SD Recorder remote control Gen Eye SD Video Pipe Inspection Location Syst
4. followed by 1 9 ex ESC 5 Type text on screen Press F5 to save screen text to selected page AL wy NOR Table 1 Reel Selection Guide Lengths Reel Type Pipe Sizes Available Standard 3 to 10 200 300 or 400 ft Reel 75 to 300mm 60 90 or 120m T 1 1 2 to 4 100 or 200 ft Mini Reel 38 to 100mm 30 or 60m SKIDS Depending on the size of pipe you are inspecting you may need to use the supplied skid so the camera is cen tered of off the bottom of the pipe Care should be taken so the skids do not snag in the pipe Under normal operating situations the camera is used with the smaller protective sleeve in 4 lines or the larger finned sleeve in 6 and larger pipes The skids supplied should be slipped onto the camera with the lip of the sleeve at the front Make sure the cam era body is clean and the set screws tightened only until they touch the camera body Do not over tighten as you may damage the camera housing Gen Eye SD Video Pipe Inspection Location System RECORDING THE INSPECTION 1 Make sure you have established live image on the monitor prior to recording OPERATION 2 Insert an SD card into the SD card reader 1 Slowly push the camera into the pipe Make sure the spring does not kink or double back on itself 2 Once the camera is in the pipe adjust the lights to a level which produces the best picture with the least amount of light This will vary
5. if dropped or butted severely against the pipe or any other hard surface The stainless steel camera housing is made to protect the camera and electronics to a large ex tent however it can be damaged by denting which may cause possible failure of the protective and wa tertight O ring seals that may cause the camera to fail The camera housing and front viewing lens should be checked thoroughly after each use for signs of damage and if required should be corrected prior to further use e The camera should always be cleaned and inspected after every use as dirt grime and grease can cause unnecessary problems such as failure of the camera seals e The standard camera spring is attached to the cable via three 3 4 40 x stainless steel hex socket cap screws This connection includes an O ring sealing the connection from water leakage This connection should be checked after every use to ensure that the screws have not loosened during the course of the inspection e f disconnecting the camera from the push rod make sure that the O ring is in good condition and or re placed when replacing the camera onto the push rod e The camera lens front nose piece and lights should be cleaned and checked after every use for possible damage to the lens or light covers and to prevent a build up of dirt and grime which may cause a degra dation of the video picture e Should camera disassembly be required for any rea son for rep
6. should be taken to check the entire length on any pipe you are going to inspect Prevent object and liquid entry Never push ob jects of any kind into this product through the open ings as they may touch dangerous voltage points or short circuit to parts that could result in a fire or elec tric shock Never spill liquid of any kind on the prod uct Tool Use and Care 1 Use clamps or other practical way to secure and support the workpiece to a stable platform Hold ing the work by hand or against your body is unstable and may lead to loss of control Do not force tool Use the correct tool for your application The correct tool will do the job better and safer at the rate for which it is designed Do not use tool if switch does not turn it on or off Any tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect the plug from the power source be fore making any adjustments changing accesso ries or storing the tool Such preventative safety measures reduce the risk of starting the tool acciden tally Store idle tools out of reach of children and other untrained persons Tools are dangerous in the hands of untrained users Maintain tools with care Keep cutting tools sharp and clean Properly maintained tools with sharp cut ting edges are less likely to bind and are easier to control Inspect for misalignment or binding of moving parts breakage of parts and any other condition
7. Gen Eye SD Video Pipe Inspection Location System Operating Instructions Your Gen Eye Video Pipe Inspection Location System is designed to give you years of trouble free profitable service However no machine is better than its op erator Read understand and follow all safety warnings and instructions provided with the product Failure to follow the warnings and instructions may result in electric shock and or serious injury Save all warn ings and instructions for future reference SAVE THESE INSTRUCTIONS PIPE CLEANERS Gen Eye SD Video Pipe Inspection Location System GENERAL SAFETY RULES Read and understand operator s manual before using this machine Failure to follow operating instructions could result in death or serious injury WARNING Read and understand all instructions Failure to follow all instructions listed below may result in electric shock fire and or serious personal injury Replacement manuals are available upon request at no charge or may be downloaded from our web site www drainbrain com Instructional videos are available for download on our website and may be ordered If you have any questions or problems please call General s customer service department at 412 771 6300 SAVE THESE INSTRUCTIONS These instructions are intended to familiarize all personnel with the safe operation and maintenance procedures for the Gen Eye SD Video Pipe Inspection Location Syst
8. OR SYSTEM DISCONNECT POWER FROM THE CONTROL UNIT BEFORE REMOVING OR RECONNECTING THE CAMERA TO THE REEL The camera and associated electronics are not user ser viceable Servicing should be left to qualified personnel your dealer can advise you with regards to service etc In the event the camera needs to be returned to the fac tory the following instructions should be used with ex treme care to remove the camera head and spring from the end of the cable 1 On standard reels disconnect the complete camera and spring assembly by removing the 3 screws 4 40 x 2 SSTL that are countersunk into the cone shaped aluminum coupler at the end of the push ca ble The screws can be removed using the Xcelite allen wrench provided with the unit Screws should be removed very carefully and simultaneously Each screw should be turned approximately one 1 full turn alternatively so as not to damage the connector While backing out each screw hold the connector and camera assembly together until all the screws are out and then unplug the camera from the cable reel taking care not to lose the O ring or screws 2 After unplugging the camera inspect the O ring for any damage and if worn replace it with a new one Also when replacing any O rings make sure there is no dirt or grit on it as it may not seal properly and apply silicon grease or petroleum jelly to the O ring for proper sealing 3 To reconnect carefully align the rear co
9. Press F4 followed by or and five digits Press ENTER to confirm Save current on screen text to memory page Time and Date ON OFF toggle ENTER Move cursor to next line Backspace erases letter and goes back one position ESC ESC followed by 1 9 recalls saved pages on screen CTRL D Set Time Date ENTER to quit Reposition counter in one of the four cor JOIN GES ners and the bottom center of the screen CTRL B Type black characters with white border CTRL F Turn flashing characters ON CTRL N Turn flashing characters OFF CTRL W Type white characters COUNTER SET UP Before starting the inspection and only after you have placed the camera in the line you should make sure to zero your counter This is your starting point for measure ments TO SET THE COUNTER To set the counter to a preset value press the F4 key Then press either or followed by five digits numbers To set the counter to 0000 0 press F4 fol lowed by ENTER SETTING TIME DATE Hold CTRL and press D YYMMDDHHMMSSam ap pears on the screen Type in the correct time and date in this order year month day hour minutes seconds am pm a for AM and p for PM If you wish to quit simply hit the ENTER button and date and time entry line will dis appear Note that the clock mode is 12 hour i e 01 to 12 SAVING A PAGE To save a page to memory go to the page you wish to save by pressing ESC
10. at the SD recorder is working properly e Check that there is enough memory available on the SD card e Check whether the inserted SD card is formatted cor rectly e Check that the SD card hasn t been locked e Disconnect the main power source and contact the factory service department FOR ALL OTHER FUNCTIONS RELATIVE TO THE SD RECORDER OR MONITOR UNIT PLEASE CONSULT YOUR RECORDER OR MONITOR OWNER S MANUAL FOR MORE INFORMATION CONTACT THE DRAIN BRAINS AT General PIPE CLEANERS 412 771 6300 or 800 245 6200 www drainbrain com info drainbrain com Gen Eye SD Video Pipe Inspection Location System GENERAL S LIMITED WARRANTY General s Gen Eye SD video pipe inspection location system carries a two year warranty against defect in materials except as noted below Should any part break or fail to work properly in the two years following purchase it will be repaired or replaced at our discretion at no charge Damage due to negligence improper usage failure to follow instructions accidents or alteration from original design is not covered by this warranty In order to handle any adjustment with a minimum of delay please follow this procedure 1 Return the part to your wholesaler and have them notify us immediately with complete information on the problem 2 We must have the serial number the date of purchase and the name of the wholesaler from whom you tool was purchased To activate yo
11. ds gases or dust Power tools create sparks which may ignite the dust or fumes Keep bystanders children and visitors away while operating a power tool Distractions can cause you to lose control Electrical Safety l Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances Never remove the grounding prong or modify the plug in any way Do not use any adapter plugs Check with a quali fied electrician if you are in doubt as to whether the outlet is properly grounded If the tool should electrically malfunction or break down grounding provides a low resistance path to carry electricity away from the user Avoid body contact with grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is grounded Do not expose power tools to rain or wet condi tions Water entering a power tool will increase the risk of electric shock Do not abuse the cord Never use the cord to carry the tools or pull the plug from an outlet Keep cord away from heat oil sharp edges or moving parts Replace damaged cords immedi ately Damaged cords increase the risk of electric shock When operating a power tool outside use an out door extension cord marked W A or W These cords are rated for outdoor use and reduce the risk of electric shock Keep all electric connections dry and off the ground Re
12. duces the risk of electric shock Do not touch plugs or tools with wet hands Re duces the risk of electric shock Personal Safety 1 Stay alert watch what you are doing and use common sense when operating a power tool Do not use tool while tired or under the influence of drugs alcohol or medication A moment of inat tention while operating power tools may result in seri ous personal injury Dress properly Do not wear loose clothing or jewelry Contain long hair Keep your hair cloth ing and gloves away from moving parts Loose clothes jewelry or long hair can be caught in moving parts Gen Eye SD Video Pipe Inspection Location System Remove adjusting keys or switches before turn ing the tool on A wrench or key that is left attached to a rotating part of the tool may result in personal injury Do not overreach Keep proper footing and bal ance at all times Proper footing and balance en ables better control of the tool in unexpected situa tions Always wear safety glasses and rubber soled non slip shoes Dust mask non skid safety shoes hard hat or hearing protection must be used for ap propriate conditions Rubber glove inserts should be worn for health and safety reasons Sewer lines are unsanitary and may contain harmful bacteria Check to make sure pipes are not electrically hot In some cases ground circuits may be returned to cast iron pipes causing them to be electrically charged Care
13. em This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety mes sages that follow this symbol to avoid possible injury or death DANGER indicates a hazard with a high level of risk which if not avoided will result in death or serious injury WARNING indicates a hazard with a medium level of risk which if not avoided could result in death or serious injury CAUTION indicates a hazard with a low level of risk which if not avoided will result in minor or moderate injury Electric shock resulting in death can occur if you plug this machine into an improp erly wired outlet If the ground wire is electrified you can be electrocuted by just touching the machine even when the power switch is off A ground fault circuit interrupter will not pro tect you in this situation Use a UL approved tester to determine if the outlet is safe Do not operate power tools in explosive atmospheres such as in the presence of flamma ble liquids gases or dust Power tools create sparks which may ignite the dust or fumes Always wear safety glasses and rubber soled non slip shoes Use of this safety equip ment may prevent serious injury GENERAL SAFETY RULES Work Area 1 Keep work area clean and well lit Cluttered benches and dark areas invite accidents Do not operate power tools in explosive atmos pheres such as in the presence of flammable liq ui
14. em CAMERA LOCATION 1 Turn the Gen Eye SD power switch to ON 2 Switch the Locator ON and check that the battery indicator shows at least one bar Replace batteries as needed 3 Make sure the Locator is set for the same frequency as the transmitter by pressing the Frequency button FREQ until the desired frequency appears on the display 4 Press Antenna Select ANT SEL so that the indica tor arrow points to TWIN PEAK 5 Press the UP arrow so that the gain bar is at the maximum setting 6 Hold the Locator blade vertical and in line with the camera head handle of the Locator at 90 degrees to the camera head If you are not sure of the direction of the pipe hold the locator above the drain opening and rotate it until you obtain the maxi mum signal Note The camera must be stationary to be precisely pinpointed 7 Move the Locator forward and back ward and side to side along the camera path until you obtain a peak response on the display 8 If the display indicates a maximum signal of 100 re duce the gain by pressing the DOWN arrow to keep the display at approximately 50 70 9 Repeat step 7 and 8 as you narrow your search area 10 A small ghost signal may appear in front and behind the peak reading Lower the gain button until you receive only one signal 11 When you can only receive the signal in a small one foot square area you ve located the camera Mark the spot Tip I
15. lacing seals etc always ensure the cam era has first been cleaned and taken to a clean area for disassembly Take extra precaution to avoid dirt getting into the camera body and any mating compo nents such as the nosepiece main body and con nectors Gen Eye SD Command Module The SD Command Module Should not be used in wet lo cations or in the rain as mois ture may cause damage to the unit Fuses for line voltage camera and camera lights are located behind the LCD monitor panel Should replacement become necessary replace only with the same value and type as the original Never substitute fuses as damage may oc cur and may void your warranty However if the fuses continue to trip for no apparent reason please consult the factory and do not use the system until the problem has been determined Camera Transmitter 512HZ The standard camera system includes a 512 Hz transmit ter which is located safely in the spring behind the cam era When the Command Module is turned on the trans mitter will be automatically activated CARE SHOULD BE TAKEN WHEN USING THE TRANSMITTER IN THE SPRING AS EXCESSIVE BENDING AND TWISTING MORE THAN 180 DEGREES MAY DAMAGE THE UNIT Gen Eye SD Video Pipe Inspection Location System Pre Inspection Procedure On arrival to the job site and after checking for a properly grounded receptacle see Gen Eye SD Command Mod ule set the SD Command Module in an easily viewable positio
16. me control on the SD Command Mod ule is turned up too high AC Power Input Socket The supplied AC power cord is plugged into this socket for main power to the unit DO NOT PLUG IN BOTH AC AND DC CORDS AT THE SAME TIME Cable Reel Input Socket 10 Pin This is used to connect the interface cord from the cable reel to the SD Command Module Main Power Select Switch After selecting either the 120 volt AC power cord or the 12 volt DC power cord plug it in and turn this switch to the appropriate setting to power up the SD Command Module Camera Lights Variable Intensity Control Controls light output and intensity on camera light head Camera Test Terminal Use this connector to troubleshoot video or light problems 1 Disconnect the system from the power source 2 Remove camera from cable assembly and plug into Cam era Test Terminal 3 If the lights are still not working chances are that one or more of the lights will need replacement Contact General for service This will help isolate where camera video or light prob lems may be originating Example If the lights were not working when the camera was connected through the cable reel but they do work when you plug directly to the front panel this indicates a problem with the light wire somewhere in the cable reel Always check fuses first Fuses The SD Command Module contains three replaceable fuses located behind the front LCD panel one each for the ca
17. mera power 0 5 amp AC line 3 amp and cam era lights 0 25 amp These are rated at 250 volts and are approximately 1 4 diameter x 1 1 4 long IF THE FUSES CONTINUE TO TRIP DO NOT USE THE SYSTEM TRY TO DETERMINE THE CAUSE OR HAVE A QUALIFIED PERSON CHECK OUT THE PROBLEM Gen Eye SD Video Pipe Inspection Location System TROUBLESHOOTING COMMAND MODULE No Picture AND No Lights e Check to see if the Main Power switch is ON e Check that the SD Recorder power is ON e Check that Monitor Power is ON and SOURCE is set to the proper position e Check to make sure that the camera lens is not cov ered or looking at a surface that provides no detail therefore any image detail e Check all connections and connectors from the cam era back to the Command Module including the cable reel e Disconnect main power and contact the factory ser vice department Picture BUT No Lights e Check if Main Power switch is ON and in correct posi tion e Check to see if LIGHT power switch is ON and inten sity control is turned up e Check cable for possible breaks or intermittent open circuits by flexing the cable No Picture Lights OK e Check Monitor power switch is ON Check to make sure the power source is live for 120 volt AC or check to see if the light is lit on the cigarette lighter plug for 12 volt DC e Check to see if the CAMERA power fuse has tripped If so replace with same value
18. n where it will not interfere with the inspection For AC Voltage Operation Plug the socket end of the AC cord into the AC socket on the panel of the Command Module When using 120 volts AC care should be taken to ensure that it is plugged into a properly grounded receptacle to prevent damage to the unit For DC Voltage Operation Plug the socket end of the DC cord into the DC socket on the panel of the Command Module When using 12 volts DC the unit plugs into a vehicle s cigarette lighter For 12VDC the vehicle engine must be running to operate the camera system THE AC OR DC CORD SHOULD ALWAYS BE PLUGGED INTO THE SD COMMAND MODULE FIRST THEN INTO THE WALL OR 12VDC SOCKET NEVER PLUG INTO THE AC SOCKET OR DC 1 Check and make sure the LED Dimmer Control is set at the min position 2 Unwind the interface cord from the side of the reel and plug it into the Reel input connector on the panel of the SD Command Module Insure the connector is properly aligned and then tighten 3 Once all connections have been checked plug the other end of the AC cord or DC cord into the appro priate power source 120VAC or 12VDC 4 Set the power switch on the Command Module to either the 120 VAC or 12 VDC position Gen Eye SD Video Pipe Inspection Location System KEYBOARD COUNTER OPERATING INSTRUCTIONS FUNCTION Cursor ON OFF Clear screen and place cursor at home position i e top left corner
19. nnector on the camera assembly and the cable reel connector When aligned push the connectors together and re place the screws If the connectors do not align properly turn the camera body slowly while slightly pushing the two connectors together until you feel them align properly together DO NOT FORCE THE CONNECTORS TOGETHER DAMAGE MAY OCCUR TO THE CONNECTORS Gen Eye SD Video Pipe Inspection Location System CAMERA FOCUS All Gen Eye SD cameras are pre focused at the factory from approximately 3 to infinity and should not require any focus adjustments Should focus adjustments be re quired please call the factory CAMERA CONTROL UNIT FUNCTIONS AND CONTROLS The SD Command Module is designed to supply all oper ating voltages and functions to your camera system and should be treated with care Protecting the unit from ex cessive shock and jarring will prolong its life Separate AC and DC Power Cords are available The 3 prong AC plug on the AC cord and a cigarette lighter type plug on the 12 VDC cord Microphone ON OFF Switch Turn this switch to the ON position to record your voice Be sure you do not accidentally have the switch ON as it will record any audio in the vicinity of the SD Command Module Condenser Microphone This is the actual microphone that receives the audio for recording purposes If you hear audio feedback a screeching sound when trying to use the microphone it is because the volu
20. that may affect the tool s operation If damaged have the tool serviced before using Many accidents are caused by poorly maintained tools Only use accessories that are recommended by the manufacturer for your model Accessories that may be suitable for one tool may become hazardous when used on another tool Gen Eye SD Video Pipe Inspection Location System Service 1 Tool service must be performed only by qualified repair personnel Service or maintenance per formed by unqualified repair personnel could result in injury 2 When servicing a tool use only identical replace ment parts Follow instructions in the Mainte nance section of this manual Use of unauthorized parts or failure to follow Maintenance Instructions may create a risk of electric shock or injury a SAFETY RULES Do not use tool if switch does not turn it ON or OFF Any tool that cannot be controlled with the switch is dangerous and must be repaired 2 Be sure that the unit is plugged into a properly grounded receptacle If in doubt check receptacle before plugging in machine Check the power cord to see that there are no cuts or frays and that the grounding prong on the plug is still in place 3 If the power cord supplied with the machine is not long enough be sure to use a 16 gauge heavy duty extension cord no more than 50 feet long and in good condition Using lighter cords can result in severe power loss and motor overheating 4 Be caref
21. ts much easier to locate the camera when it s closer to the drain opening than when it s 100 feet away Push the camera five or ten feet into the line then do your first location Mark the spot and push the camera ahead another five or ten feet then repeat When you re done you ll have the whole line traced and marked An instructional video is available at www drainbrain com Locator Peak Signal Ghost nosi Signal eight tf enn Radiated iy yi Signal a a l y l A et Fl Camera DEPTH MEASUREMENT 1 Recheck the camera location using the steps outlined above 2 Rest the tip of Locator on the ground holding it verti cally above the pinpointed position of the camera head 3 Press the DEPTH button The LCD screen will indi cate the depth of the camera 4 You can select the unit of measurement feet inches meters centimeters by pressing the DEPTH button and the DOWN arrow at the same time Note An indication of four dashes on the display can be caused by too much or too little signal strength Adjust the gain and recheck the depth measurement See complete Locator instruction manual for more information An instructional video is available at www drainbrain com Gen Eye SD Video Pipe Inspection Location System MAINTENANCE CAMERA CLEANING After every use the camera should be cleaned and checked for possible damage that may have occurred during the inspection External scuffing of the
22. ul when cleaning drains where cleaning chemicals have been used Avoid direct contact with corrosive drain cleaners Drain cleaning chemi cals can cause serious burns as well as damage the cable Neutralize or remove corrosive drain cleaners in the drain before starting the job 5 Do not operate machine if operator or machine is standing in water Will increase risk of electrical shock 6 Wear safety glasses and rubber soled non slip shoes Use of this safety equipment may prevent serious injury 7 Protect against lightening For added protection for this product during a lightning storm or when it is left unattended and unused for long periods of time un plug it from the wall outlet This will prevent damage to the product due to lightning and power surges 8 Protect against excessive heat The product should be situated away from heat sources such as radia tors heat registers stoves or other products including amplifiers that produce heat FEATURES Voice Over Microphone amp Switch LED Dimmer Control Camera Connection 8 LCD Color Monitor Video Audio Out Jack Camera Test Jack Power Switch DC Power Inpu AC Power Input Full Keyboard w 8 Pages of Memory SD Card Reader Storage Compartment Padded Case Under Keyboard ABOI THE INSPECTION CAMERA The camera although manufactured for the harsh environments in which it will be used should be treated carefully as damage may occur
23. ur Gen Eye warranty your warranty card which has this information must be filled out and sent to us im mediately after your machine is purchased 3 We will then advise your wholesaler if the part should be returned to us and as sign a return goods authorization RGA number Ship freight prepaid and you will be compensated for these charges if it is determined that the part is defective If repairs are necessary due to conditions beyond our control or if the item is out of war ranty we will do the work at the lowest possible cost but a charge will be made This warranty is made in place of all other warranties express statutory or implied includ ing those of merchantability and of fitness for purpose General shall not be responsible for any incidental or consequential damages This warranty gives you specific legal rights and you may also have other rights which vary from state to state Some states do not allow the exclusion of limitation of incidental or con sequential damages so these limitations may not apply to you General Wire Spring Co 1101 Thompson Avenue McKees Rocks PA 15136 412 771 6300 www drainbrain com General Wire Spring Co 2009 C GESDOI 0709
Download Pdf Manuals
Related Search