Quick Start Guide
Contents
1. lax testitire MULTI STIMULUS DETECTOR TESTER 5 Using the Menus Menu Navigation Keys Menu Key Status Key Using the UP and DOWN menu navigation keys I 1 you can move the cursor through the MAIN menu Press the ENTER key to select stimuli from the MAIN menu 6 Turning the Unit On To turn the unit on press and hold the red ON OFF key for 2 seconds 14 The Status LED will flash slowly green to indicate that the unit is in STANDBY mode Pressing the ESCAPE key amp goes back to the MAIN menu or when a test sequence has been programmed and the MAIN menu is displayed the ESCAPE key will cancel the programmed test sequence The first time the unit is powered on you will be prompted to select the operating language for your region Use the UP and DOWN keys to navigate and use the ENTER key to select your language 15 gt English Deutsch Espa ol Fran ais Enter Key Keypad A DOWN arrow w on the bottom right of the MAIN menu indicates more options are available below English Use the DOWN key on the keypad to move down through the menu 12 This will display a confirmation screen 16 Press the MENU key to confirm or the STATUS key to cancel The MAIN menu will be displayed Select Cancel The UP arrow on the MAIN menu2. Heat and Smoke can be combined as the first operation Menys Aat followed by a CO test Note you will need to lower the head unit between each test To delete a test setup use the ESCAPE key www testifire com Note It is very important that the detector under test is in the correct position 22 Ideally the bellows should seal against the ceiling surface Programme the tests Smoke 1 Heat 1 Raise Testifire over the detector t Smoke and Heat are tested at the same time as test 1 Lower Testifire from the detector The test is completed and ready to test another detector in the same way Programme the tests Smoke 1 Heat 2 COS Raise Testifire over the detector Smoke is tested as test 1 Lower for 2 10 seconds then raise Testifire again Heat is tested as test 2 Lower for 2 10 seconds then raise Testifire again CO is tested as test 3 Lower Testifire The test is completed and ready to test another detector in the same way Using these methods you can programme Testifire to combine tests and continue in sequence In this example Smoke and Heat are tested together as test 1 and then CO is tested as test 2 Note Clear clearing can also be selected in any of the above operations lax testifire Test Type LED Status L
3. D shows STANDBY mode testifire MULTI STIMULUS DETECTOR TESTER www testifire com Inner Clear Cup Platform Clear Cup Bellows RFID Antenna Infrared Beam Main Duct for Heat Smoke and CO Testifire 100 RFID Bluetooth Module Smoke Capsule TS3 10 CO Capsule TC3 1 USB Port on rear of unit 2 User Interface Display LCD 13 Test Type LED 14 Status LED 15 Smoke Capsule Access Cover 16 CO Capsule Access Cover 17 Adjustable Handle 18 Battery Baton 19 Infrared Remote Control Receivers oOnN OU DWN Depending on model specification Future option Replacement Capsules A Testifire Smoke Capsule TS3 B Testifire CO Capsule TC3 A User Interface Keypad C Menu Key D Status Key E Menu Navigation Keys F Enter Key G ON OFF Key H Escape Key testifire 25 Infrared Remote Control AA Operation Indicator LED BB Contol Button Infrared Remote Control Generation of test stimuli starts when Testifire is positioned over a detector and remote controls are not generally required Certain detectors such as those with virtual chambers have no physical features to cause stimuli generation to start The optional infrared remote control can be used to initiate the test procedure in such situations General Safety Information CAUTION Please refer to your User Manual and take clearnote of all warnings and cautions before using your T
4. ED gt Smoke Heat CO 2 Menu Status Menu Smoke Heat gt CO lt Menu Status gt Smoke 1 Heat 1 com v Menu Status Heat a CO gt Clear Menu Status www testifire com Blue Solid Smoke Test in progress Red Solid Heat Test in progress Green Solid CO Test in progress Red Blue Green Alternating Smoke Heat and CO test in progress at the same time Simultaneous Testing Blue Solid then Red Green Alternating Test in progress portion of Smoke then Heat amp CO combined testing Sequential Testing Not Illuminated Clearing mode in operation Green Slow Flashing STANDBY Mode Green Fast Flashing OPERATIONAL Mode test in progress Red Flashing slow red flashing in STANDBY mode or fast red flashing in operation Battery needs charging Testifire still operational Alternating Red Green Flashing TIME OUT Indication after 2 minutes of continuous testing on one stimulus or combination of stimuli Red Solid Error see message on display refer to User Manual for a complete list of Indicating LED Error Messages Green Solid CO Cooling Status LED blips red or green The next test will start when the capsule has cooled sufficiently Alternating Red and Green fast flashes with long gaps CO Cooling phase Indication after a CO test has been carried out Further CO test cannot be carried out until Status LE
5. d e g Smoke 23 flashing faster Raise the Testifire head unit up to the detector to be tested and place it centrally over the detector 2 Simultaneous Testing selected tests at the same time In this example Smoke and Heat are selected as a Smoke 1 simultaneous test 24 w Move the cursor to Smoke and press the ENTER key Menu Status 1 will be displayed alongside Smoke Move the cursor to Heat and press the ENTER key 2 will be displayed alongside Heat Press ENTER once more to display 1 alongside Heat Repeat the above as required for additional stimuli To delete a test setup use the ESCAPE key 3 Sequential Testing selected tests one after another In this example Smoke Heat and CO are selected as a w sequential test 25 cos o Move the cursor to Smoke and press the ENTER key MEE estes 1 will be displayed alongside Smoke Move the cursor to Heat and press the ENTER key 2 will be displayed alongside Heat Move the cursor to CO and press the ENTER key O will be displayed alongside CO To delete a test setup use the ESCAPE key 4 Combined Simultaneous and Sequential Testing In this example Smoke and Heat are combined as a Smoke 1 simultaneous test followed by CO 26 Heat 1 coe g
6. estifire Testifire has no user serviceable parts Do not disassemble Refer to the manual for Service and Support information cetectortesters C testing technology from No Climb No Climb Products Ltd Edison House 163 Dixons Hill Road Welham Green Hertfordshire AL9 7JE United Kingdom As our policy is one of continuous improvement details of products described within this publication are subject to change without notice All information provided here is believed to be correct at the time of going to press Every effort has been made to ensure the accuracy of information which is provided in good faith but nothing contained herein is intended to incorporate any representation or warranty either express or implied or to form the basis of any legal relations between the parties hereto additional to or in lieu of such as may be applicable to a contract of sale or purchase
7. indicates more options available above Use the UP key on the keypad to move up through the menu 13 Press the LEFT key on the keypad to go back one menu level gt CO Clear Menu Status Preparing for use Please wait After long periods of non use or when a Smoke Capsule has been replaced the unit will self prime at power on The Preparing for use Please wait message will be displayed for a short period 17 8 Testing High Profile Detectors When testing high profile detectors remove the inner clear cup Place your finger in the cut out and carefully lift out the inner cup 20 This will allow the detector to touch the platform 21 7 Adjusting the Head Angle Correct head angle adjustment is important The detector should touch the base of the inner clear cup 22 To adjust the head unit hold the body 18 and pulling gently against the spring angle the head unit away from the Battery Baton 19 The head unit will lock and remain in that position for testing www testifire com lax testitire MULTI STIMULUS DETECTOR TESTER How to Perform a Test To carry out a simple single stimuli As the detector enters Testifire the infrared beam STR test use the UP and DOWN keys is interrupted by the body of the detector and the on the keypad to highlight the stimulus chosen test will begin indicated by the Status LED Menu Status require
8. le into the capsule port Push it into position ensuring that the clips spring out positively on both sides of the capsule Close the access cover A securely To insert the Battery Baton hold the Testifire head unit by the handle and depress the upper spring button on the Battery Baton Align the button with the location hole in the handle and push the Battery Baton into the handle until the button springs up through the location hole 5 Insert the other end of the Battery Baton into the Solo access pole and depress the lower spring button Align it with the location hole and push the Battery Baton further into the pole until the button springs up through the hole 6 4 Removal amp Replacement of CO Capsules Testifire 2000 series only Spring Clips I EE Removal Only replace the CO capsule when it is empty Turn Testifire off for five minutes to allow the capsule to cool down before removing it Release the lower access cover D 9 by opening it from the right hand side Squeeze the spring clips E on each side and gently pull the capsule out Do not touch the tip of the CO capsule as it may be hot Replacement Remove the capsule from its carton and Anti Static bag Remove the tip protector F 10 Hold the capsule by the spring clips with the label uppermost Carefully insert into position ensuring that the clips spring out positively on both sides Close the access cover D securely
9. testifire Quick Start Guide Multi Detector Test U Apparatus Used to Verify a Detector s Functional Operation SIGNALING www testifire com Quick Start Guide to testifire MULTI STIMULUS DETECTOR TESTER Battery Charger for Solo Testifire Scorpion duct Code Solo 725 001 a mains power outlet or a 2 volt vehicle socket I When connected the red Power LED will illuminate Connect the Battery Baton to the charger and turn the locking ring 2 amp 3 The yellow Fast Charge LED will illuminate 4 Charge times vary but can be 75 90 minutes when charging a fully discharged Battery Baton When fully charged the charger will switch to Trickle Charge and the green LED will illuminate 4 Note Use only NiMH Battery Batons with Testifire 3 Removal amp Replacement of Smoke Capsules testifire 1000 amp 2000 series Spring Clip Protector Spring Clips www testifire com Removal Release the upper access cover A 7 on the body of the Testifire by opening it from the right hand side Note Testifire 1000 series units only have one access cover Squeeze the two clips B of the used capsule and gently pull the capsule out Replacement Remove the capsule from its outer carton and Anti Static bag Remove the spring clip protector cap from the new capsule C 8 Holding the capsule by the spring clips with the label on the underside carefully insert the new capsu
Download Pdf Manuals
Related Search