Quick Start Guide
Contents
1. Observe the SM audio level LEDs while speaking or singing into the microphone at the same voice level that will be used during the program While holding the AUDIO button press the Up or Down arrow buttons until the both the 20 and 10 LEDs glow green with the 20 LED oc casionally flickering red 0 dB to 10 dB range during peaks Note Setting the audio level too high reduces the dynamic range of the audio signal Setting the audio level too low may cause hiss and noise in the audio 5 Ifthe unit was set up in Standby Mode it will be necessary to power up the SM and adjust the remaining components of the audio system prior to use Locking or Unlocking the Control Panel 1 Ensure the SM setup is complete The Lock mode protects the transmitter from unLoc accidental changes to its settings 2 Simultaneously press both the Up and Down arrow buttons to start the Lock timer When the timer reaches zero Loc is displayed and the controls are locked Important The only ways to unlock a locked transmitter are to remove the battery or unlock it via the remote control It cannot be unlocked or powered off using the buttons The remote control will work only if the transmitter was previously configured to respond to the remote control The unit will always power up in unlocked mode www lectrosonics com 5 Battery Installation We recommend using lithium or high capacity rechargeable batteries for longe2. LECTROSONICS wy SM Series Transmitters SMA SMV SMQV RM a z 4 LECTROSONICS oc U S Patent 7 225 135 This guide is intended to assist with f initial setup and operation of your Serial Number Lectrosonics product For a detailed user manual down load the most current Purchase Date version at www lectrosonics com manuals 06 jun10 Controls and Functions LCD Screen Battery Compartment Cover Plate UP Arrow Antenna Battery Compartment Opener Patera TepoeC POWER RITON LOCK 100 n EE DOWN Arrow Modulation 20Q aupio FREQ 4 z LEDs PWR ourcx gt SANDBY RF OFF Audio _ A Input Jack PowerLED AUDIO Button FREQ Button Tuning LCD Screen Used to display the status of the selected function Power LED Indicates power status and battery strength Audio Input Jack Accommodates most lavaliere and dynamic microphones and line level signals Modulation LEDs Provides a visual indication of the audio input signal level either red or green to indicate modulation levels Audio Button Used to display the audio level setting 0 dB to 44 dB on the LCD and used with the Up and Down arrows to adjust the audio level input from the micro phone FREQ Button Used to set the operating frequency and toggle the LCD between the operating frequency in MHz and a two digit hexadecimal frequency code Up Down Arrows Used to adjust the selected function or parameter Ba
3. be set to 35 50 70 100 120 and 150 Hz 4 LECTROSONICS INC Attaching a Microphone and Adjusting Gain The front panel Modulation LEDs indicate limiter ac tivity See chart below Once set the transmitter s audio level setting should not be used to control the volume of your sound system or recorder levels Signal Level 20 LED 4oLep This gain adjustment matches the trans Less than 20 dB O oft Oott mitter gain with the microphone s output 20 dB to 10 dB Green O off level the user s voice level and the micro 10 dB to 0 dB Green Green phone s position The audio input level can 0 dB to 10 dB Red Green be set with the unit in Standby Mode or Greater than 10dB__ Red Red powered up for normal operation 1 2 3 4 Note Different voices will usually require different settings of the AUDIO control so check this adjustment for each person using the system If several different people will be using the transmitter and there is not time to make the adjustment for each individual adjust it for the loudest voice With the SM powered off insert the microphone plug into the Audio Input Jack aligning the pins and ensuring that the connector locks Place the SM in Standby Mode or if the unit is to be powered up and ad justed mute the main sound system prior to powering up the transmitter Position the microphone in the location where it will be used in actual operation
4. fect develop Lectrosonics Inc will at our option repair or replace any defective parts without charge for either parts or labor If Lectrosonics Inc cannot correct the defect in your equipment it will be replaced at no charge with a similar new item Lectrosonics Inc will pay for the cost of returning your equipment to you This warranty applies only to items returned to Lectrosonics Inc or an authorized dealer shipping costs prepaid within one year from the date of purchase This Limited Warranty is governed by the laws of the State of New Mexico It states the entire liablility of Lectrosonics Inc and the entire remedy of the purchaser for any breach of warranty as outlined above NEITHER LECTROSONICS INC NOR ANYONE INVOLVED IN THE PRODUCTION OR DELIVERY OF THE EQUIPMENT SHALL BE LIABLE FOR ANY INDIRECT SPECIAL PUNITIVE CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THIS EQUIPMENT EVEN IF LECTROSONICS INC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN NO EVENT SHALL THE LIABILITY OF LECTROSONICS INC EXCEED THE PURCHASE PRICE OF ANY DEFECTIVE EQUIPMENT This warranty gives you specific legal rights You may have additional legal rights which vary from state to state LECTROSONICS a Made in the USA by a Bunch of Fanatics 581 Laser Road NE e Rio Rancho NM 87124 USA www lectrosonics com 505 892 4501 800 821 1121 fax 505 892 6243 sales lectrosonics com
5. her in MHz or as a two digit hexadecimal num ber Pressing the FREQ button toggles between the two display modes The frequency can be set Frequency displayed with the unit in Standby Mode or while powered up in MHz for normal operation Note You must first find a clear frequency with the receiver then set the transmitter to match Frequency displayed as two digit hexadecimal To change the Operating Frequency of the SM number Series transmitter 1 Press the FREQ button to enter this screen Note The default display is in MHz Pressing the FREQ button again displays the operating frequency as a two digit hexadecimal number 2 While holding the FREQ button use the Up or Down arrow buttons to move the operating frequency up or down in 100 kHz increments from the current setting Holding the Up or Down arrows will cause rapid scrolling through the frequencies Note The operating frequency displayed on the LCD wraps as it reaches the upper or lower end of its range Thus if you intend to move the operating frequency from the lower end of the range to the upper end it may be faster to do this by using the Down arrow until the frequency wraps to the upper end Adjusting the Low Frequency Roll off Repeatedly press the AUDIO button until the LF roll off adjustment screen appears Then press and hold the AUDIO button while selecting the desired roll off frequency with the UP and DOWN arrows The roll off frequency can
6. ibility Modes Also the SM exits the Compatibility Mode screen to Standby Mode See Standby Mode this section Note The unit comes from the factory configured as a 400 Series transmitter 1 Set the receiver s audio controls to minimum 2 Power up the SM and observe the Boot Sequence If the Compatibility Mode for the SM does not match the corresponding receiver then power off the SM transmitter 3 From a power off condition press and hold the Up arrow then press the AUDIO and FREQ buttons simultaneously 4 The LCD will display the current Compatibility Mode Use the Up or Down arrow buttons to set the Compatibility Mode to match the corre sponding receiver www lectrosonics com 3 The following Compatibility Modes are selectable e 100 Series mode CP 100 e 200 Series mode CP 200 e Mode 3 Contact factory for details CP 3 e 400 Series mode CP 400 e IFB Series mode CP IFB e Mode 6 Contact factory for details CP 6 5 The Compatibility Mode selected in Step 4 will be the current Compatibili ty Mode until reset using this procedure Pressing AUDIO or FREQ exits into the Standby Mode To power off from the compatibility mode screen press AUDIO and FREQ together 6 Press either AUDIO or FREQ button to select power setting screen and use the up down arrows for your desired level of power 50 100 or 250mw Setting Transmitter Operating Frequency The Operating Frequency of the SM is displayed eit
7. microphone The longest usable range is about e Lock or Unlock modes 6 feet depending on the microphone and volume e Sleep mode ON OFF settings In the power saving sleep mode power consumption drops to 20 of normal Powering the RM On and Off Press the AUDIO and FREQ buttons together briefly Principles of Operation The RM user interface is organized into pages which are accessible via the AUDIO and FREQ buttons Once on a page settings can be adjusted with the UP and DOWN arrow buttons Only the specific function displayed is altered The AUDIO button cycles through 4 pages 1 Aud set transmitter s audio level 2 SLEEP unSLP cause transmitter to sleep or wake up 3 Loc unLoc lock or unlock transmitter s buttons 4 Loud adjust RM speaker volume press SEND button for a sample tone The FREQ button cycles through 3 pages 1 CH set transmitter s channel using block independent hex code 2 b select a block number optional uncovers page 3 3 000 000 set transmitter s frequency in MHz avail if a block is selected www lectrosonics com 7 LIMITED ONE YEAR WARRANTY The equipment is warranted for one year from date of purchase against defects in materials or workmanship provided it was purchased from an authorized dealer This warranty does not cover equipment which has been abused or damaged by careless handling or shipping This warranty does not apply to used or demonstrator equipment Should any de
8. rce through a battery eliminator Power Restore will return your transmitter to settings it had before it was powered off This eliminates the need to power on through the unit itself PLAC 1 Press and hold the Down Arrow Button then power on the transmitter by pressing the Audio and Freq buttons simultaneously Power Restore Screens 2 The LCD will display the status either rc ON or rc OFF Press AUDIO or FREQ key to scroll to the PbAc 0 setting and use arrow keys to turn to PbAc 1 for on 3 When power is restored the unit will turn on with previous settings 6 LECTROSONICS INC RM Remote Control Operating Instructions LCD Display UP Arrow Button Battery Cover SEND eno SSCTROSONICS Button Lanyard Attachment DOWN Arrow ak 2 Sleep 2 BLOCK ADJUST Button AUDIO putton O Goo m2 Gu aa Batre Battery Level Indicator 3 LOCK 3 FREQ 4 LOUD FREQ Button The RM gives you remote control of SM Series transmitters using an audible tone delivered to the transmitters microphone When the SEND button is pressed a dweedle tone will play from the RM speaker and the parameter on the transmitter will be set immediately The transmitter must be configured to accept commands from the RM see page 6 Adjustments can be made to set e Audio input gain Note The speaker should be uncovered and Frequency held within a few inches of the transmitter s
9. st life Note Standard zinc carbon batteries marked heavy duty or long lasting are not adequate The battery status circuitry is designed for the volt age drop over the life of lithium batteries To install new batteries 1 Turn the Battery Cover Plate Opener counter clockwise open the battery compartment and remove any old batteries 2 Insert the new battery or batteries into the housing positive terminal first Important On dual battery transmitters BOTH batteries go positive terminal first 3 Replace the Battery Cover Plate and tighten the Opener Configuring for Remote Control Use Some transmitter settings can be changed with the Lectrosonics RM Remote Control However you must first configure the SM Series transmitter to oneal accept commands from the RM 1 Press and hold the Down Arrow Button then power on the transmitter by pressing the Reinote Control Screens Audio and Freq buttons simultaneously 2 The LCD will display the status either rc ON or rc OFF To change the setting press the Up or Down arrow button 3 Power Off the transmitter by pressing the Audio and Freq buttons simulta neously The RC setting will persist when you Power Up the transmitter again Note SM Series transmitters with firmware version 1 6 and later are factory set to rc ON by default Configuring for Power Restore smvz smav omy When using external power sou
10. ttery Compartment Cover Plate and Opener Used to install or remove battery batteries 2 LECTROSONICS INC Operating Instructions Power On 1 Ensure that good batteries are installed 2 Simultaneously press and hold the AUDIO and FREQ buttons until the Power On Boot Initial Power On Sequence is initiated 3 seconds Timer Screen Power Off 1 Simultaneously press and hold the AUDIO and FREQ buttons while observing that the word Off appears in the LCD along with a counter 2 When the counter reaches 0 the unit turns off Initial Power Off Timer Screen Note If the AUDIO and FREQ buttons are released before the end of the countdown the unit will not turn off Standby Mode From the OFF position quickly press and release both the AUDIO and FREQ buttons simultaneously to enter and exit this mode Allows the user to verify or change the transmitters operating frequency or Standby Screen audio input level without transmitting any signals Selecting the Compatibility Mode and Power smv a smov on SM Series transmitters will work with all Digital Hybrid Wireless receivers in the native compand orless mode They are also capable of working with 200 Series 100 Series and IFB analog receivers 400 Series or Digital plus some other brands of analog wireless receiv Hybrid Wireless ers contact the factory for details Compatibility Mode Note RF transmission is prevented while selecting Compat
Download Pdf Manuals
Related Search