Be1 Auto Start Kit USER Manual
Contents
1. Enter the AUTO mode see 2 3 Push and hold for at least 5 seconds the AUTO pushbutton until the yellow LED will start blinking the engine will start automatically To stop the engine push the AUTO or one of the O pushbuttons Section 3 0 Display measurements The Be1 features a 4 Digit display and 4 pushbuttons as indicated below Display mode Display information Alarm acknowledge and horn indicators pushbutton silence pushbutton Left control display button __ Right control a display button Poa 6 F Fuer C vac Use and gt to select a function Use to display the name of the function The following table lists the functions of the display 4 digit DISPLAY Be 1 User Manual June 2015 page 4 Disblay Function Display Pushbuttons used Push to indicate the play indication to select the function name of the parameter Generator Voltage UXXX voLt Generator Frequency HXX X HErt Speed R P M XXXX lt or gt rPM Battery Voltage Vdc bXX X bAtt Charger Voltage Vdc cXX X cHAr Oil Pressure Bar PXX X bAr Oil Pressure Bar sensor not used P bAr Fuel Level 0 up to 99 F XX FUEL Fuel Level sensor not used F FUEL Coolant temperature C C 1 Oil Temperature C XXX C 2 Canopy Temperature C C 3 Coolant temperature not used t1 C 1 Oil Temperature not2. indicates the recent one G To display the code of the Event push the pushbutton see table 4 10 NOTE in case that the supply switch is not available consult your panel manufacturer
3. Be 1 User Manual June 2015 page 1 Be 1 User Manual GENERATOR AUTO START KIT The information in this document is subject to change without notice No part of this document may be copied or reproduced in any form or any means without the prior written consent of Bernini Design Company Bernini Design assumes no responsibility for any errors which may appear in this instruction manual Customer Support BERNINI DESIGN SRL ITALY e mail bernini bernini design com Mobile support 39 335 7077148 40 721 241361 Warranty Bernini Design SRL hereinafter BD warrants that Be 1 shall be free from defect in material or workmanship for a period of 3 years from the BD delivery date BD shall at its option repair or replace the product without charge BD shall return the Be 1 to the buyer with the Default parameters at no extra charge The buyer shall furnish sufficient information on any alleged defects in the product so as to enable BD to determine their cause and existence If the Be 1 is not defective or the product is defective for reason other than covered by this warranty the buyer will be charged accordingly This warranty shall not apply if the Be 1 has not been used in accordance with the User Manual and other operating instruction particularly if any defects are caused by misuse improper repair attempts negligence in use or handling The warranty does not include the membrane keyboard front panel in case of visible signs of misuse T
4. Push one of the I pushbuttons until the display indicates the message MAn and all LEDs illuminate release the button B Push one of the pushbuttons until engine starts The display indicates the message during the starting attempt and in case of pre glow When the engine is running the green LED START ON will illuminate C To stop the engine push one of the O pushbutton until the StOP message appears on the display If the engine has already stopped it is possible to cancel the STOP sequence by pressing the O pushbutton Push O when the engine is not running if you want to shutdown the panel Note if the display blinks indicating the message ALAr consult section 8 0 ALARM WARNINGS and SHUTDOWNS 2 3 AUTO mode Push AUTO until the yellow LED on the button will illuminate The engine starts when you activate the Remote Start and stops when you de activate the Remote Start input if provided by your panel manufacturer In AUTO mode the Be 1 will periodically test the engine if programmed by your panel supplier During this test the yellow LED AUTO will continue to blink Once the Be 1 isin AUTO mode push the AUTO pushbutton for a short time if you want to select the manual mode see 2 2 In case of alarms it is not possible to select the AUTO mode Note if the display blinks indicating the message ALAr consult section 8 0 ALARM WARNINGS and SHUTDOWNS 2 4 TEST mode
5. and provides A a general indication of alarm presence by means of the message ALAr on the display B 4 LEDs to indicate Oil pressure Temperature Fail to start and Over speed shutdown C display messages indicating warnings and shutdowns see Table 4 10A B D an ACK pushbutton to silence the Horn To silence the HORN if provided by you panel manufacturer push the ACK pushbutton To browse the alarm memory push the gt pushbutton To display the details of the alarm push the pushbutton To clear totally the alarm remove the cause and press the O pushbutton The tables 4 10A B in the section 4 0 indicate all possible alarms Section 8 1 Event History INSTRUCTIONS for QUALIFIED PERSONNEL ONLY The Be 1 features an Event History register able to record the last 100 shutdown events To read the contents of the memory follow the instructions A Turn OFF the DC power supply of Be 1 NOTE B Push and hold the pushbutton C Apply the power supply continue to hold the pushbutton D Release the pushbutton when the display turns on E The display will indicate the code of the last event E 01 Push the the pushbutton to display the name of the Event Alarm events have the same display message used for alarm indication see secion 4 10A B F You can select an event from E 01 to E100 using the lt and pushbuttons E100 indicates the oldest event E01
6. el Engine amp Generator parameters warnings and shut downs See figure 1 Figure 1 Front Panel Layout Pushbutton to Pushbutton for Alarm Acknowledge Symbols l display details lt to silence the horn see manual Left _ Arrow 7 Right 4 Digit fea Display ast Yellow LED _ mode AUTO bares ee eee Pushbutton mode AUTO Oil and Temperature i a Alarms Green LED for Engine Running V Battery Alarm Pushbutton to 2 START the Engine External Alarm or BERNINI 0o eih c Maintenance Fail to Start Overspeed Fuel and Mode selection Request Alarm Alarm Alarm Alarms Section 2 0 Mode selection The modes of operation are selected by pushbuttons Every time the power supply is switched on the Be1 enters the OFF mode unless the Be 1 was in TEST or AUTO prior to power down The following table indicates the available modes Mode Pushbutton LED indicators Section OFF O All turned Off dot on display 2 1 MANUAL 1 The yellow LED AUTO is OFF 2 2 AUTO AUTO The yellow LED AUTO is ON 2 3 TEST AUTO The yellow LED AUTO blinks 2 4 2 1 OFF mode Push one of the O pushbuttons to enter the OFF mode the Display and LEDs will turn off a dot on the display will blink slowly and the alarms will be cleared Be 1 User Manual June 2015 page 3 2 2 MANUAL mode To start and stop the engine follow the instructions A
7. his purchase is non refundable WARNING High voltage is present inside the Be 1 To avoid electric shock hazard operating personnel must not remove the protective cover Do not disconnect the grounding connection The Be 1 can start the engine at anytime Do not work on equipment which is controlled by the Be 1 When servicing the engine disconnect the battery and battery charger We recommend that warning signs be placed on equipment indicating the above 1 0 INEFOCUCTION ca ecccccenencecseneesecnereesensenteseneentnseneeres page 2 2 0 Mode of Operation S lCCtION ccccsseereee page 2 2 VOFF MOOG iiini acs avshscbibas sepals aasa iai page 2 2 2 MANUAL MODE ssisnsrssiriasriresbnnisni inanan page 3 25S AUTO MOIE riais akiai page 3 24 TEST MOE nesransnsuonani ara page 3 3 0 DISPLAY MeASUrCMENKS 11ccseecsserreeertessereees page 3 4 0 DISPLAY MCSSAQECS 1 scsecccseerccsseesssernsnensesneneees page 4 4 10 Alarm Messages eecceceeeeteeteetteeetenteeeetees page 4 4 20 Operating MOSSAGES cccccccsccceestetseteeetsees page 5 5 0 LED indicators and Test LEDS 2 ccccsss000 page 6 6 0 READING the parameter 1cccceeccseercssersseee page 6 8 0 Alarms Event History 111cccccseecccseeeeeeeseeenees page 6 Be 1 User Manual June 2015 page 2 Section 1 0 Introduction The Be 1 is a microcontroller based engine protection module It provides visual indication by means of LEDs and Display for Fuel Lev
8. ime before cranking r The Be 1 is performing the pre glow The measurement is out of range StoP The Be 1 is stopping the engine PO j P1_ Indicates that the engine is going to start or stop following according to the status of a Remote Switch consult your panel manufacturer Be 1 User Manual June 2015 page 6 Section 5 0 LED solid state lamps indicators and Test of the LEDs To test the LEDs and DISPLAY push and hold the and pushbuttons simultaneously in OFF or MANUAL mode The LEDs and DISPLAY remain energized as long as the pushbuttons are pressed and held together 6 0 Reading the parameters To read the setting of the parameters follow the instructions 1 Press one of the O pushbutton until the LEDs and display turn OFF 2 Push the lt or gt pushbutton to select a parameter 3 Push to display the setting of the parameter 4 Push the lt or pushbutton to select another parameter Consult your panel manufacturer for details NOTE if the pushbuttons remain inoperative for more than 2 minutes the Be 1 turns off the display Section 8 0 Alarms Warnings and Shutdowns I WARNING Always consult your supplier or the user manual of the engine A short description of the alarm follows below Recommendations for solving the problem are also indicated The Be 1 features shutdowns the engine stops and warnings the engine will continue to run
9. one bAtt Battery Voltage Warning High or Low Vdc indication C 1 High EngineTemperature shutdown C 2 High Oil Temperature shutdown C indication if C 3 High Canopy Temperature shutdown the sensor is not C 4 High Engine Temperature Warning me the seid C 5 High Oil Temperature Warning wi a the C 6 High Canopy Temperature Warning message S on FUEL Fuel level warning High or Low indication Er 06 Low Fuel Shutdown AL 01 AL 05 Programmable Alarm if provided by your panel none manufacturer Er 07 Failure of a Sensor Oil pressure Temperatures or Fuel Level InP 1 InP5 Er 08 Maintenance Service when this warning turns on you are not allowed to none enter the AUTO mode F StP Fail to Stop Alarm none F Str Fail to Start Alarm none Err Memory Failure none ALt Alternator Failure none nderspee pee U SPd Und d Speed O SPd Overspeed Shutdown i ver Frequency Shutdown requency Hi H Over F Shutd F Lo H Under Frequency Shutdown i ver Voltage Shutdown oltage ac Hi U Over Vol Shutd Vol Lo U Under Voltage Shutdown TABLE 4 20 Be 1 Operating messages Message Description Message Description rESt The Be 1 is counting the rest timing CooL It indicates the coolling down time the period of time between the starting engine runs off load before stopping attempts The Be 1 is starting the engine dEL Delay t
10. used t2 C 2 Canopy Temperature not used t3 C 3 Hours count up to 50 000 h Over 9999h the display indicates a dot on the XXXX Hour right Example 1234 will mean 12340h NOTE X indicates a numerical digit if the measurement is out of range the display will indicate Section 4 0 Display messages The Be indicates alarms messages table 4 10A B and operating messages table 4 20 1 WARNING Always consult your supplier or the user manual of the engine A short description of the alarm follows below Recommendations for solving the problem are also indicated Alarm messages The presence of an alarm in the memory is indicated by the message AIAr Push to display the alarm Push to search for other alarms Push ACK to acknowledge the alarm see also sect 8 0 Message TABLE 4 10A Description of the Alarm Button ALAr Indicates the presence of an alarm Push and to display the alarm see the list below OIL P Low Oil Pressure Warning Bar indication Er 01 Low Oil Pressure Shutdown bELt Engine Belt Break Shutdown It energizes if the Charger Alternator fails to Vdc indication work or if the belt is broken Be 1 User Manual June 2015 page 5 Message TABLE 4 10 B Description of the Alarm Button PicK The Be 1 detects a failure of the pick up N
Download Pdf Manuals
Related Search