Home

User`s Manual

1. CD R TAIYO YUDEN CO LTD Mitsui Chemicals Inc MITSUBISHI CHEMICAL CORPORATION RICOH Co Ltd Hitachi Maxell Ltd CD RW High Speed MITSUBISHI CHEMICAL CORPORATION Multi Speed RICOH Co Ltd DVD R DVD Specifications for Recordable Disc for General Version 2 0 TAIYO YUDEN CO LTD PIONEER VIDEO CORPORATION Matsushita Electric Industrial Co Ltd DVD R MITSUBISHI CHEMICAL CORPORATION RICOH Co Ltd DVD RW DVD Specifications for Rerecordable Disc for Version 1 1 VICTOR COMPANY OF JAPAN LIMITED TDK Corporation DVD RW MITSUBISHI CHEMICAL CORPORATION RICOH Co Ltd DVD RAM DVD Specifications for DVD RAM Disc for Version 2 0 or Version 2 1 Matsushita Electric Industrial Co Ltd 4 12 User s Manual Operating Basics If the disc is poor in quality dirty or damaged writing or rewriting errors may occur Be careful to check the disc for dirt or damage before you use it The actual number of rewrites to CD RW DVD RW or DVD RW is affected by the quality of the disc and the way it is used There are two types of DVD R discs authoring and general use discs Do not use authoring discs Only general use discs can be written to by a computer drive You can use DVD RAM discs that can be removed from a cartridge and DVD RAM discs designed without a cartridge You cannot use a disc with a 4 7 GB single sided capacity or 9 4 GB double sided capacity Other DVD ROM drives for computers or other DVD players may n
2. Soft key Key combinations that emulate keys on the IBM keyboard change some configuration options stop program execution and access the numeric keypad overlay software The set of programs procedures and related documentation associated with a computer system Specifically refers to computer programs that direct and control the computer system s activities See also hardware stop bit One or more bits of a byte that follow the transmitted character or group codes in asynchronous serial communications subpixel Three elements one red one green and blue RGB that make up a pixel on the color LCD The computer sets subpixels independently each may emit a different degree of brightness See also pixel synchronous Having a constant time interval between successive bits characters or events system disk A disk that has been formatted with an operating system For MS DOS the operating system is contained in two hidden files and the COMMAND COM file You can boot a computer using a System disk Also called an operating system disk Glossary 12 User s Manual Glossary T terminal A typewriter like keyboard and CRT display screen connected to the computer for data input output TFT display A liquid crystal display LCD made from an array of liquid crystal cells using active matrix technology with thin film transistor TFT to drive each cell TouchPad A pointing device integrated into the TOSHIBA computer pa
3. batch file A file that can be executed from the system prompt containing a sequence of operating system commands or executable files binary The base two number system composed of zeros and ones off or on used by most digital computers The right most digit of a binary number has a value of 1 the next a value of 2 then 4 8 16 and so on For example the binary number 101 has a value of 5 See also ASCII BIOS Basic Input Output System The firmware that controls data flow within the computer See also firmware bit Derived from binary digit the basic unit of information used by the computer It is either zero or one Eight bits is one byte See also byte board A circuit board An internal card containing electronic components called chips which perform a specific function or increase the capabilities of the system boot Short for bootstrap A program that starts or restarts the computer The program reads instructions from a storage device into the computer s memory bps Bits per second Typically used to describe the data transmission speed of a modem buffer The portion of the computer s memory where data is temporarily stored Buffers often compensate for differences in the rate of flow from one device to another bus An interface for transmission of signals data or electric power User s Manual Glossary 3 Glossary byte The representation of a single character A sequence of eight bits treat
4. l Sound mute Pressing Fn Esc in a Windows environment turns sound on or off When you press these hot keys the current setting will change and be displayed as an icon User s Manual 5 3 The Keyboard ape Instant security Press Fn F1 to blank the screen to prevent others from accessing your data To restore the screen and original settings press any key or press the Dual Pointing Device If a screensaver password is registered a dialog box will appear Enter the screensaver password and click OK If no password is set the screen will be restored when you press any key or press the Dual Pointing Device q s Power save mode Pressing Fn F2 changes the power save mode If you press Fn F2 in a Windows environment the Power Save Mode is displayed in a dialog box similar to the one below Continue holding down Fn and press F2 again to change the setting You can also change this setting through the profile item in TOSHIBA Power Saver EI e Standby When you press Fn F3 the computer enters Standby To avoid entering Standby unexpectedly a dialog box appears for verification However if you select the check box it will not appear in the future Du Hibernation When you press Fn F4 the computer enters Hibernation To avoid entering Hibernation unexpectedly a dialog box appears for verification However if you select the check box it will not appear in the future An Display selection Pres
5. 100 800 x 600 16M 16M 16M 16M 60 75 85 100 1024 x 768 16M 16M 16M 16M 60 75 85 100 1280 x 1024 16M 16M 16M 16M 60 75 85 100 1400 x 1050 16M 16M 16M 16M 60 1600 x 1200 16M 16M 16M 16M 60 Virtual 75 85 100 1920 x 1440 16M 16M 16M 16M 60 Virtual 75 2048 x 1536 16M 16M 16M 16M 60 Virtual 75 Some SVGA modes are not supported at LCD CRT simultaneous mode and LCD CRT Multi Monitor mode User s Manual B 9 Display Controller and Modes B 10 User s Manual TECRA M2 Appendix C AT Commands In most cases you will not need to type AT commands manually However there might be some occasions when you will need to do so This chapter describes AT commands for data mode Fax and voice commands are taken care of by application software The format for entering AT commands is ATXn where X is the AT command and n is the specific value for that command After you type in the command press Enter Any command issued is acknowledged with a response in either text or numeric values known as result codes All commands and command values accepted by the modem are described in this section any entry other than those listed results in an error Escape sequence The escape sequence allows the modem to exit data mode and enter on line command mode While in on line command mode you can communicate directly to your modem using AT commands Once you finish you can return to data mode usi
6. 11 Secure the modem board with two screws removed in step 9 12 Insert tabs on the front of the keyboard into corresponding notches on the computer and seat the keyboard 13 Two screws secure the keyboard 14 Seat the keyboard brace and press to secure latches 15 Install the battery pack User s Manual Internal Modem Guide Removing the internal modem To remove the internal modem follow the steps below noapoann 8 9 Save your data and turn off the computer Disconnect the AC adaptor and any other peripheral device Turn the computer upside down and remove the battery pack Perform the step from 4 to 9 of installation the internal modem Remove two screws and remove the modem board Disconnect the modem cable Insert tabs on the front of the keyboard into corresponding notches on the computer and seat the keyboard Two screws secure the keyboard Seat the keyboard brace and press to secure latches 10 Install the battery pack Refer to the installation procedures for details EES A02 0604JP F 2 User s Manual TECRA M2 Appendix G Wireless LAN Card Specifications Form Factor Mini PCI Typelll Compatibility W IEEE 802 11 Standard for Wireless LANS W Wi Fi Wireless Fidelity certified by the Wi Fi Alliance The Wi Fi CERTIFIED logo is a certification mark of the Wi Fi Alliance Network Operating Wi Microsoft Windows Networking System Media Access BW CSMA C
7. purchased a Install an additional memory module to Slot B for the computer with vacant Slot B b You can increase the memory amount by replacing the memory module in Slot A and or B with a memory module of larger memory amount when both Slot A and Slot B are occupied However replacing of memory module in Slot B is recommended because it is easier to replace the memory module in Slot B than A c Itis strongly recommended to leave the replacing of memory module preinstalled in Slot A to TOSHIBA dealer because the installing or replacing of memory module in Slot A needs skill E Place a mat beneath the computer to prevent making a scratch on the lid when replacing the memory module Avoid the mat that generates static electricity W When you remove a memory please do not touch other portions of a computer User s Manual 8 5 Optional Devices A i W Use only memory modules approved by TOSHIBA E Do not try to install or remove a memory module under the following conditions You can damage the computer and the module Also data will be lost a The computer is turned on b The computer was shut down using the Standby mode or Hibernation mode c Wake up on LAN is enabled If you install a memory module that is not compatible with the computer beep will sound when you turn on the power If the module is installed in slot A there will be a long beep 1 second followed by two short beeps 0 5 second eac
8. s Manual IMQ KEMA NEMKO SEMKO AC Power Cord and Connectors France UTE Switzerland SEV Germany VDE United Kingdom BSI In Europe power cords must be VDE type HO5VVH2 F and two conductor For the United States and Canada plug configuration must be a 2 15P 250 V or 1 15P 125 V as designated in the U S National Electrical code handbook and the Canadian Electrical Code Part Il The following illustrations show the plug shapes for the U S A and Canada the United Kingdom Australia and Europe USA and Canada United Kingdom UL approved CSA approved BS approved Australia Europe Approved by the AS approved appropriate agency H 2 User s Manual TECRA M2 Appendix Parts Numbers The computer configuration and parts numbers printed on a label on the bottom of the computer indicate the CPU LCD memory HDD and communication devices Configurations The following table shows the computer configuration indicated on a label Shaded areas indicate abbreviations used on the label The explanations are to the left of the shading Abbreviations are not limited to those in this chart They may change without notice CPU LCD Memory HDD Communication Pentium M 1 4G PM1 4 14 TFT XGA 14X 256 0MB 256M 30GB 30 802 11b without BT WLb antenna 1 5G PM1 5 14 TFT SXGA 14 256 256MB 512M 40GB 40 802 11b with BT antenna WLb B
9. 200 cece eee 2 12 USB floppy disk drive 20 0c eee 2 13 User s Manual Table of Contents Optical media drives 2 0 ccc nennen nn 2 14 Region codes for DVD drives and media 2 14 Writable dises i side eee ee kek ee cls hea eh haar an 2 14 CDS insu ne dete eb ctu cient Etat ed eee eee wk ke 2 14 DVDS PTS 2 15 Formats PT 2708 2000R beh ape nee bows d eE Onin aE 2 15 CD ROM drive 1 0 0 tees 2 15 DVD ROM drive ssssssseee e 2 15 CD RW DVD ROM drive 0 0 0 cece ee 2 15 DVD Multi drive 0 2 eee 2 16 DVD R RW drive DVD Dual drive 0 000008 2 16 AC adapton 4 zx ee pie eee eee 2 17 Chapter 3 Getting Started Setting up your work Space 0 cee eee 3 1 General conditions lt srs sseni erince cee eee nennen 3 2 Placement of the computer rennen 3 2 Seating and posture 20 0c esee 3 3 Lighting is ra ie bow ha Oe eee pate dus pus 3 3 Work Habits vain 2 24 0002 DE Rec LAUR a x La an ar 3 4 Connecting the AC adaptor 00 022 e eee eee 3 4 Opening the display 00 0c eee eee 3 5 Turning on the power Hua eee eee eee eee 3 6 Windows XP setup 2200 eee eee eee 3 7 Turning off the power 2000 eee eee 3 7 Shut Down mode Boot mode 0 00 cee eee 3 7 Hibernation mode gaii aeae ae then eee eee Rade 3 7 Standby mode ce szx chente hha yed ee Rn eee 3 9 Restarting the comp
10. Digital video cameras Hard disk drives MO drives CD RW drives F i LINK uses a four pin connector which does not carry electriccurrent 1 External devices will need their own power supply Precautions Make a back up of your data before transferring it to the computer There is a possibility that the original data will be damaged There is a particular risk that some frames will be deleted in the case of digital video transfer TOSHIBA assumes no liability for such loss of data Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise Data can be destroyed If you are transferring data through an IEEE1394 hub do not connect or disconnect other devices from the hub during data transfer There is a likelihood that data will be damaged Connect all devices to the hub before you turn on the computer s power You may not use any copyrighted video or music data copied from a video camera except for your personal enjoyment If you connect disconnect an i LINK device to from another i LINK device that is currently exchanging data with the computer data frames might be dropped Make sure data transfer has ended or turn off the computer before you Connect disconnect an i LINK device to from the computer Connect disconnect an i LINK device to from another i LINK device that is connected to the computer Connecting 1 2 Make sure the connectors are properly alig
11. Is the computer making any unusual noises Write down what you hear Record your observations so you can describe them to your dealer 9 2 User s Manual Troubleshooting Software Hardware The problems may be caused by your software or disk If you cannot load a software package the media may be damaged or the program might be corrupted Try loading another copy of the software If an error message appears while you are using a software package check the software documentation These documents usually include a problem solving section or a summary of error messages Next check any error messages in the OS documentation If you cannot find a software problem check your hardware First run through the items in the preliminary checklist above If you still cannot correct the problem try to identify the source The next section provides checklists for individual components and peripherals Hardware and system checklist This section discusses problems caused by your computer s hardware or attached peripherals Basic problems may occur in the following areas System start up Self test Power Password Keyboard LCD panel Hard disk drive DVD ROM drive CD RW DVD ROM drive DVD Multi drive DVD R RW drive DVD Dual drive floppy disk drive SD card System start up When the computer does not start properly check the following items B Self Test B Power Sources EM Power on Password PC card
12. Try changing the double click speed setting in the mouse control utility 1 Open the Control Panel select the Mouse icon and press Enter 2 Click the Buttons tab 3 Setthe double click speed as instructed and click OK Try changing the speed setting in the mouse control utility 1 Open the Control Panel select the Mouse icon and press Enter 2 Click the Pointer Options tab 3 Setthe speed as instructed and click OK The mouse might be dirty Refer to your mouse documentations for instructions on cleaning If problems persist contact your dealer Refer also to your USB device s documentation Problem USB device does not work Procedure Check for a firm cable connection between the USB ports on the computer and the USB device Make sure the USB device drivers are properly installed Refer to your Windows XP documentation for information on checking the drivers If problems persist contact your dealer User s Manual Troubleshooting Memory expansion Refer also to Chapter 8 Optional Devices for information on installing memory modules Problem Procedure Beep sounds Make sure the memory module installed in the Two beeps a dash expansion slot is compatible with the computer and a dot for a If an incompatible module has been installed defective memory follow the steps below module in slot A 1 Disconnect the AC adaptor and all peripheral Three beeps a dash devices and two d
13. User s Manual 6 17 Power and Power Up Modes Power up modes The computer has the following power up modes B Boot Computer shuts down without saving data Always save your work before you turn the computer off in boot mode B Hibernation Data in memory is saved to the hard disk E Standby Data is maintained in the computer s main memory Refer also to the sections Turning on the power and Turning off the power 1 in Chapter 3 Getting Started Windows utilities You can specify the setting in TOSHIBA Power Saver Hot keys You can use hot keys Fn F3 to enter Standby mode and Fn F4 to enter Hibernation See Chapter 5 The Keyboard for details Panel power on off You can set up your computer so that power turns off automatically when you close the display panel When you open the panel power turns on in Standby or Hibernation mode but not in boot mode gt If the panel power off function is enabled and you use Shut down 1 Windows do not close the display until the shut down function is completed System Auto Off This feature turns the system off automatically if it is not used for a set duration The system shuts down in Standby mode or Hibernation mode in Windows 6 18 User s Manual TECRA M2 Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer TOSHIBA HW Setup lets you configure settings for Display CPU Boot Priority Keyboard USB LAN G
14. W When the computer is shut down in standby mode the power indicator flashes orange E fyou are operating the computer on battery power you can lengthen the operating time by shutting down in hibernation mode Standby mode consumes more power Standby limitations Standby will not function under the following conditions W Power is turned back on immediately after shutting down B Memory circuits are exposed to static electricity or electrical noise Restarting the computer Certain conditions require that you reset the system For example if E You change certain computer settings Wi An error occurs and the computer does not respond to your keyboard commands Wi There are three ways to reset the computer system 1 Click start then click Turn off computer From the Turn off computer menu select Restart 2 Press Ctrl Alt Del to display the Windows Task Manager then select Shutdown and Restart 3 Select Restart from the Turn Off Computer window in the start menu 4 Press the power button and hold it down for five seconds Wait 10 to 15 seconds then turn the power on again by pressing the power button 3 10 User s Manual Getting Started Restoring the preinstalled software from the Product Recovery DVD ROM If preinstalled files are damaged use the Product Recovery DVD ROM to restore them To restore the operating system and all preinstalled software follow the steps below When you reinstall the W
15. When the CPU temperature falls to a normal range the fan is turned off and the CPU operation returns to standard speed If the CPU temperature reaches an unacceptably high level with either setting the system automatically shuts down to prevent damage Data in memory will be lost User s Manual 4 27 Operating Basics 4 28 User s Manual TECRA M2 Chapter 5 The Keyboard The computer s keyboard layouts are compatible with a 101 102 key enhanced keyboard By pressing some keys in combination allthe 101 102 key keyboard functions can be executed on the computer The number of keys on your keyboard depends on which country region s keyboard layout your computer is configured with Keyboards for numerous languages are available There are five types of keys typewriter keys keypad overlay function keys soft keys and cursor control keys Typewriter keys The typewriter keys produce the upper and lower case letters numbers punctuation marks and special symbols that appear on the screen There are some differences however between using a typewriter and using a computer keyboard E Letters and numbers produced in computer text vary in width Spaces which are created by a space character may also vary depending on line justification and other factors B The lowercase el and the number 1 one are not interchangeable on computers as they are on a typewriter E The uppercase O oh and the 0 ze
16. equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Wi Reorient or relocate the receiving antenna Wi Increase the separation between the equipment and receiver W Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Wi Consult the dealer or an experienced radio TV technician for help Only peripherals complying with the FCC class B limits may be attached to this equipment Operation with non compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception Shielded cables must be used between the external devices and the computer s external monitor port USB port parallel port IEEE1394 port and microphone jack Changes or modifications made to this equipment not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user s authority to operate the equipment FCC conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation User s Manual iii User s Manual Contact Address TOSHIBA America Information Systems Inc 9740 Irvine Boulevard Irvine California 92618 1697 Telephone 949 583 3
17. multi speed CD RW discs or high speed 4 to 10 speed discs The write speed of the ultra speed CD RW discs Ultra speed is CD RW DVD ROM drive only is maximum 24 speed 2 14 User s Manual The Grand Tour DVDs B DVD R discs can be written only once The recorded data cannot be erased orchanged B DVD RW discs can be recorded more than once B DVD RAM discs can be recorded more than once Formats The drives support the following formats B DVD ROM B DVD Video CD DA W CD Text Photo CD single multi session B CD ROM Mode 1 Mode 2 CD ROM XA Mode 2 Form1 W Enhanced CD CD EXTRA Form2 Wi Addressing Method 2 B CD G Audio CD only DVD ROM drive The full size DVD ROM drive module lets you record data to rewritable CDs as well as run either 12 cm 4 72 or 8 cm 3 15 CD DVDs without using an adaptor F The read speed is slower at the center of a disc and faster at the outer 1 edge DVD read 8 speed maximum CD read 24 speed maximum CD RW DVD ROM drive The full size CD RW DVD ROM drive module lets you record data to rewritable CDs as well as run either 12 cm 4 72 or 8 cm 3 15 CD DVDs without using an adaptor 1 The read speed is slower at the center of a disc and faster at the outer edge DVD read 8 speed maximum CD read 24 speed maximum CD R write 24 speed maximum CD RW write 24 speed maximum high speed media User s Manual 2 15 The Grand Tour DVD Multi drive The
18. partially charged or no charge No 2nd battery installed AC Main battery adaptor charge is above not low battery connected trigger point Main battery charge is below low battery trigger point Main battery charge is exhausted No main battery installed Power on Operates No charge LED 2nd Battery green DC IN 15V green Operates Charge LED 2nd battery orange DC IN 15V green Operates No charge LED 2nd battery off DC IN 15V green Operates LED Battery off DC IN 15V off Operates LED Battery flashes orange DC IN 15V off Computer shuts down e No operation LED Battery off DC IN 15V off Table 6 1 Power conditions continued Power off no operation No charge LED 2nd battery green DC IN 15V green Quick charge LED 2nd battery orange DC IN 15V green No charge LED 2nd Battery off DC IN 15V green 6 2 User s Manual Power and Power Up Modes Table 6 1 Power conditions continued Power on Power off no operation AC 2nd battery Operates adaptor charge is above ED 2nd battery off not low battery DC IN 15V off connected trigger point 2nd battery Operates charge is below LED 2nd battery low battery flashes orange trigger point DC IN 15V off 2nd battery Computer shuts down charge is exhausted No 2nd battery No operation 5 installed LED 2nd battery off DC IN 15V off
19. receive or transmit data operating system A group of programs that controls the basic operation of a computer Operating system functions include interpreting programs creating data files and controlling the transmission and receipt input output of data to and from memory and peripheral devices output The results of a computer operation Output commonly indicates data 1 printed on paper 2 displayed at a terminal 3 sent through the serial port of internal modem or 4 stored on some magnetic media Glossary 10 User s Manual Glossary P parallel interface Refers to a type of information exchange that transmits information one byte 8 bits at a time See also serial interface parity 1 The symmetrical relationship between two parameter values integers both of which are either on or off odd or even O or 1 2 In serial communications an error detection bit that is added to a group of data bits making the sum of the bits even or odd Parity can be set to none odd or even password A unique string of characters used to identify a specific user The computer provides various levels of password protection such as user supervisor and eject pel The smallest area of the display that can be addressed by software Equal in size to a pixel or group of pixels See pixel peripheral component interconnect An industry standard 32 bit bus peripheral device An I O device that is external to the central p
20. representative of the ASCII character marked on the key kilobyte KB A unit of data storage equal to 1024 bytes See also byte and megabyte L level 2 cache See cache Light Emitting Diode LED A semiconductor device that emits light when a current is applied Liquid Crystal Display LCD Liquid crystal sealed between two sheets of glass coated with transparent conducting material The viewing side coating is etched into character forming segments with leads that extend to the edge of the glass Applying a voltage between the glass sheets alters the brightness of the liquid crystal LSI Large Scale Integration 1 A technology that allows the inclusion of up to 100 000 simple logic gates on a single chip 2 An integrated circuit that uses large scale integration main board See motherboard megabyte MB A unit of data storage equal to 1024 kilobytes See also kilobyte megahertz A unit of wave frequency that equals 1 million cycles per second See also hertz menu A software interface that displays a list of options on the screen Also called a screen microprocessor A hardware component contained in a single integrated circuit that carries out instructions Also called the central processing unit CPU one of the main parts of the computer User s Manual Glossary 9 Glossary mode A method of operation for example the boot mode standby mode or the hibernation mode modem Derived from mo
21. the date and time it is sent and an identification of the business other entity or individual sending the message and the telephone number of the sending machine or such business other entity or individual In order to program this information into your fax modem you should complete the setup of your fax software before sending messages Instructions for IC CS 03 certified equipment A 1 The Industry Canada label identifies certified equipment This certification means that the equipment meets certain telecommunications network protective operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document s The Department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations Repairs to certified equipment should be coordinated by a representative designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that t
22. 000 e eee eee eee 8 19 User s Manual xvii Table of Contents Advanced Port Replicator Ill nnnsannn nenn 8 19 Parallel printer lille 8 20 Security lock i i a a a a XR E RR 8 21 Chapter 9 Troubleshooting Problem solving process lese RA 9 1 Preliminary checklist 2 2 sr 8 0800 ke oe nes 9 2 Analyzing the problem 2 2222er nennen nen 9 2 Hardware and system checklist 0 0 e eee eee eee 9 3 System Star Up ue xs ect Ha Hoke ste em ee di Xl E POR d eR 9 3 Selesi diegs eerie Sots Shoe Gearon enr a RO SU RC Vati Rus 9 4 POWER pP eee oe a a ne Ea ale HR 2 9 4 PASSWOrd un rai a ee 9 6 Keyboard PCM 9 7 EOD panelli zesn Sis Saki Phos Pak oe ane eee 9 7 Rand diSk driv aces tion en ie aw dew an ana Bee 9 7 DVD ROM drive ana nn esadi ee ee ee fs dE Pe aes 9 8 CD RW DVD ROM drive 1 2 0 cece 9 9 DYD Multi drive ars nto ea eek 9 10 DVD R RW drive DVD Dual drive 2 222222 ec rennen 9 11 floppy disk AVE sirg eh ears are sun ne ee en 9 12 SOCAN P TIT 9 13 PC Card iud eet versed bere eo Ret RE Er eee 9 13 Infrared POM 2 2 gcc rete RUE me x bed Ee Bog Ae oh et D na RO Re 9 13 TOSHIBA Dual Pointing Device 0 0 0 0 eee eee 9 14 Ulp EET 9 15 Memory expansion scis eig ee ee nenn nen 9 16 DOUNG SYSTEME sex zac Eu aha E ar RUE RO A ne OR as 9 16 MoriltOE i 22 en duas Ec a ee EU 9 17 i LINK JEEE1394 iii esed iR e amie
23. 1400 x 1050 1600 x 1200 1920 x 1440 2048 x 1536 LCD colors 256 256K 256 256K 256 256K 256 256K 256 256K 256 256K Virtual 256 256K Virtual 256 256K Virtual CRT colors 256 256K 256 256K 256 256K 256 256K 256 256K 256 256K 256 256K 256 256K Vertical frequency Hz 60 75 85 100 60 75 85 100 60 75 85 100 60 75 85 100 60 60 75 85 100 60 75 85 60 75 Some SVGA modes are not supported at LCD CRT simultaneous mode and LCD CRT Multi Monitor mode User s Manual B 7 Display Controller and Modes Table 3 Video modes SXGA continued Resolution 640 x 480 800 x 600 1024 x 768 1280 x 1024 1400 x 1050 1600 x 1200 1920 x 1440 2048 x 1536 LCD colors 64K 64K 64K 64K 64K 64K 64K 64K 64K 64K 64K 64K Virtual 64K 64K Virtual 64K 64K Virtual CRT colors 64K 64K 64K 64K 64K 64K 64K 64K 64K 64K 64K 64K 64K 64K 64K 64K Vertical frequency Hz 60 75 85 100 60 75 85 100 60 75 85 100 60 75 85 100 60 60 75 85 100 60 75 85 60 75 Some SVGA modes are not supported at LCD CRT simultaneous mode and LCD CRT Multi Monitor mode B 8 User s Manual Display Controller and Modes Table 3 Video modes SXGA continued Resolution LCD CRT Vertical colors colors frequency Hz 640 x 480 16M 16M 16M 16M 60 75 85
24. 222 n ss 4 12 Before writing or rewriting 00 0020 ee eee eee ee 4 12 When writing or rewriting 2l 4 14 Drag n Drop CD DVD 20000 le 4 14 Data Verification lille 4 15 Video DVD R RW RAM 2 22 22 u sense III 4 16 Video DVD R RWI RAM sssssee RII 4 16 Media care ios ae reer eee 4 17 ED DVDS icici ered er ee eee done RD SEHE ebene 4 17 floppy disks 00000 cece Is 4 17 Sound System ei ees ee wee eee ed eee a 4 18 Using the microphone 0002 cece eens 4 18 SoundMAX control panel 00200 002 eee eee eee 4 18 Audi EMG Ch ous Le ee Dear Ben abe 4 19 Modem eee eee eet RR eee eee be le ea air 4 19 Region selection 00 00 c eee eee 4 19 Properties menu 222m nasse nennen nennen nenn 4 20 SIUE TP 4 20 Connecting i 2222 24niileesklees3em 4 rear 4 21 Disconnecting 0 000 eee 4 21 Wireless communications eee BB 4 22 Wireless LAN sseeeseee RIA 4 22 Bluetooth wireless technology else 4 23 Worldwide operation liliis 4 23 Radio links ek Redon eR ee Sak ee RU sete etes 4 23 Sls 4 23 Wireless communication switch 2 22 2222 een eese 4 23 Wireless communication Indicator llle 4 24 ETT 4 24 LAN cable types ssslssllsesslles e 4 24 Connecting LAN cable 22 2 none nn 4 25 Disconnecting LAN cable 00002 0c e
25. 256K 16 of 256K 16 of 256K 16 of 256K 4 of 256K 2 of 256K Mono Mono Scanning frequency Vertical Hz 70 70 70 70 70 70 70 70 70 70 B 2 User s Manual Display Controller and Modes Table1 Video modes VGA continued Video Type Resolution Character LCD CRT Scanning mode matrix colors colors frequency pels Vertical Hz D VGA 320 x 200 8x8 16 of 256K 16 of 256K 70 Grph Pels E VGA 640 x 200 8x8 16 of 256K 16 of 256K 70 Grph Pels F VGA 640 x 350 8x 14 Mono Mono 70 Grph Pels 10 VGA 640 x 350 8x 14 16 of 256K 16 of 256K 70 Grph Pels 11 VGA 640 x 480 8 x 16 2 of 256K 2 of 256K 60 Grph Pels 12 VGA 640 x 480 8 x 16 16 of 256K 16 of 256K 60 Grph Pels 13 VGA 320 x 200 8x8 256 of 256K 256 of 256K 70 Grph Pels User s Manual B 3 Display Controller and Modes Table 2 Video modes XGA Resolution LCD CRT Vertical colors colors frequency Hz 640 x 480 256 256K 256 256K 60 75 85 100 800 x 600 256 256K 256 256K 60 75 85 100 1024 x 768 256 256K 256 256K 60 75 85 100 1280 x 1024 256 256K 256 256K 60 Virtual 75 85 100 1600 x 1200 256 256K 256 256K 60 Virtual 75 85 100 1920 x 1440 256 256K 256 256K 60 Virtual 75 85 2048 x 1536 256 256K 256 256K 60 Virtual 75 Some SVGA modes are not supported at LCD CRT simultaneous mode and LCD CRT Multi Monitor mode B 4 User s Manual Display Controller
26. 4 Never puncture the battery pack with a nail or other sharp object Never strike it with a hammer or other object Never step on it 5 Never try to charge the battery pack in any manner other than that described in the user s manual Never connect the battery pack to a plug socket or to an automobile s cigarette lighter socket It may rupture or ignite 6 Use only the battery pack supplied with the computer or other device or a battery pack approved by the computer or device s manufacturer Battery packs have different voltages and terminal polarities Use of an improper battery could cause smoke fire or rupture of the battery pack 7 Never subject a battery pack to heat such as storage near a heat Source Exposure to heat can cause the battery pack to ignite explode or leak caustic liquid and cause death or serious injury It could also fail or malfunction causing data loss User s Manual 6 7 Power and Power Up Modes 8 Never expose the battery pack to abnormal shock vibration or pressure The battery pack s internal protective device will fail causing itto overheat explode ignite or leak caustic liquids possibly resulting in death or serious injury Never let a battery pack become wet A wet battery pack will overheat ignite or rupture possibly resulting in death or serious injury Warning 1 Never allow caustic electrolyte fluid leaked from a battery pack to contact your eyes skin or clothing If caus
27. 4 2 User s Manual Operating Basics 1 To remove the AccuPoint cap firmly pinch the cap and pull it straight up Figure 4 2 Removing the AccuPoint cap 2 Position a new cap on the peg and press it into place Y The peg is square so be careful to align the cap s square hole with the peg Using the USB floppy disk drive A 3 1 2 floppy disk drive connects to the computer s USB port It accommodates 1 44 megabyte or 720 kilobyte floppy disks Refer to Chapter 2 The Grand Tour for more information Connecting 3 1 2 floppy disk drive To connect the drive plug the floppy disk drive connector into a USB port Refer to Figure 4 3 Make sure the connector is right side up and properly aligned with the socket Do not try to force the connection doing so can damage the connecting pins Q Figure 4 3 Connecting the USB floppy disk drive If you connect the floppy disk drive after turning on the computer it will 1 take about 10 seconds for the computer to recognize the drive Do not disconnect and reconnect before 10 seconds has elapsed User s Manual 4 3 Operating Basics Disconnecting 3 1 2 floppy disk drive AN When you have finished using the floppy disk drive follow the procedures below to disconnect it 1 Wait for the indicator light to go out to make sure all floppy disk activity has stopped If you disconnect the floppy disk drive or turn off the power while the computer is accessing
28. Australia Only V 90 is available in other regions The computer has built in support for Ethernet LAN 10 megabits per second 10BASE T Fast Ethernet LAN 100 megabits per second 100BASE Tx and Gigabit Ethernet LAN 1000 megabits per second 1000BASE T Some models are equipped with a Gigabit Ethernet LAN refor to the Parts Numbers section in Appendix I Some computers in this series are equipped with Bluetooth functions Bluetooth wireless technology eliminates the need for cables between electronic devices such as computers and printers Bluetooth provides fast reliable and secure wireless communication in a small space 1 8 User s Manual Introduction Wireless LAN Slim Select Bay Modules Slim Select Bay Weight Saver Some computers in this series are equipped with a Wireless LAN mini PCI card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802 11 Standard Revision A B or G and Turbo Mode B Automatic Transmit Rate Select mechanism in the transmit range of 54 48 36 24 18 12 9 and 6 Mbit s Revision A B B G A B G combo type E Automatic Transmit Rate Select mechanism in the transmit range of 11 5 5 2 and 1 Mbit s Revision B Wi Automatic Transmit Rate Select mechanism in the transmit range of 108 96 72 48 36 24 18 and 12 Mbit s Turbo Mode Revision
29. Battery indicator glows green E If you have extra battery packs rotate their use W If you will not be using the system for an extended period more than one month remove the battery pack W Disconnect the AC adaptor when the battery is fully charged Overcharging makes the battery hot and shortens life W f you are not going to use the computer for more than eight hours disconnect the AC adaptor E Store spare battery packs in a cool dry place out of direct sunlight 6 12 User s Manual Power and Power Up Modes Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one The life of the battery pack is generally about 500 recharges If the Battery indicator or Slim Select Bay indicator if a Slim Select Bay 2nd battery pack is installed flashes orange shortly after fully recharging the battery the battery pack needs to be replaced You might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source This section explains how to remove and install the battery pack For the details about removing installing the Slim Select Bay 2nd battery pack refer to Chapter 8 Optional Devices Removing the battery pack To replace a discharged battery follow the steps below A ONS When handling battery packs do not short circuit the terminals Also do not drop hit or otherwise apply impa
30. M Intel PRO Wireless Network Connection and Intel 855 Chipset Family Memory Slots Video RAM Power Battery pack RTC battery AC adaptor The slot accepts a 256 512 or 1 024 MB memory modules can be installed in the two memory slots for a maximum of 2 048MB system memory 32 or 64 MB of RAM is provided for video display The computer is powered by one rechargeable lithium ion battery pack The internal RTC battery backs up the Real Time Clock and calendar The universal AC adaptor provides power to the system and recharges the batteries when they are low It comes with a detachable power cord Because it is universal it can receive a range of AC voltage from 100 to 240 volts however the output current varies among different models Using the wrong model can damage your computer See the AC adaptor section in Chapter 2 The Grand Tour User s Manual 1 3 Introduction Disks Hard disk drive USB floppy disk drive Optional Available in four sizes 30 0 billion bytes 27 94 GB 40 0 billion bytes 37 26 GB 60 0 billion bytes 55 88 GB 80 0 billion bytes 74 52 GB Accommodates either 3 1 2 1 44 megabyte or 720 kilobyte floppy disks It connects to a USB port Computers in this series can be configured with an optical media drive installed in the Slim Select Bay The available optical media drives are described below DVD ROM drive Some models are equipped with a ful
31. Press Y key BIOS setup will terminate and the computer will be rebooted If you require any additional help using your computer or if you are having problems operating the computer you may need to contact TOSHIBA for additional technical assistance Before you call Some problems you experience may be related to software or the operating system it is important to investigate other sources of assistance first Before contacting TOSHIBA try the following B Review troubleshooting sections in the documentation for software and peripheral devices Wi ifa problem occurs when you are running software applications consult the software documentation for troubleshooting suggestions Call the software company s technical support for assistance W Consult the dealer you purchased your computer and or software from They are your best sources for current information and support 9 20 User s Manual Troubleshooting Where to write If you are still unable to solve the problem and suspect that it is hardware related write to TOSHIBA at the nearest location listed below Outside of Europe Australia TOSHIBA Australia Pty Ltd Information Systems Division 84 92 Talavera Road North Ryde N S W 2113 Sydney Canada TOSHIBA of Canada Ltd 191 McNabb Street Markham Ontario L3R 8H2 China TOSHIBA Computer Systems Shanghai Co Ltd Bldg 33 No 351 Jinzang Road Pudong New Area Shanghai P R China
32. RW R RW discs The following applications for writing are supplied on CD ROM Drag n Drop CD DVD licensed by Easy Systems Japan Ltd and DigiOn Inc InterVideo WinDVD Creator 2 Platinum which is a product of InterVideo Inc Important message DVD Multi drive Before you write or rewrite to CD R RW or DVD R RW RAM disc read and follow all setup and operating instructions in this section If you fail to do so the DVD Multi drive may not function properly and you may fail to write or rewrite lose data or incur other damage Important message DVD R RW drive Before you write or rewrite to CD R RW or DVD R RW R RW disc read and follow all setup and operating instructions in this section If you fail to do so the DVD R RW drive may not function properly and you may fail to write or rewrite lose data or incur other damage Disclaimer DVD Multi drive TOSHIBA does not bear responsibility for the following E Damage to any CD R RW or DVD R RW RAM disc that may be caused by writing or rewriting with this product W Any change or loss of the recorded contents of CD R RW or DVD R RW RAM disc that may be caused by writing or rewriting with this product or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents B Damage that may be caused by using third party equipment or software Given the technological limitations of current optical disc writing d
33. The modem will not recognize the backspace character if it is set to a value that is greater than 32 ASCII This character can be used to edit a command line When the echo command is enabled the modem echoes back to the local DTE the backspace character an ASCII space character and a second backspace character This means a total of three characters are transmitted each time the modem processes the backspace character Range 0 127 ASCII decimal Default 8 backspace Units ASCII S6 Wait before dialing This register sets the length of time in seconds that the modem must wait pause after going off hook before dialing the first digit of the telephone number The modem always pauses for a minimum of two seconds even if the value of S6 is less that two seconds The wait for dial tone call progress feature W dial modifier in the dial string will override the value in register S6 This operation however may be affected by some ATX options according to country region restrictions In some countries regions S6 will set dial tone detect time Range 3 255 Default 3 Units seconds S7 Connection completion time out This register sets the time in seconds that the modem must wait before hanging up because carrier is not detected The timer is started when the modem finishes dialing originate or goes off hook answer In originate mode the timer is reset upon detection of an answer tone if allowed by county restriction The
34. Using the wrong adaptor can damage your computer This jack lets you connect to a LAN The adaptor has built in support for Ethernet LAN 10 megabits per second 10BASE T Fast Ethernet LAN 100 megabits per second 100BASE Tx and Gigabit Ethernet LAN 1000 megabits per second 1000BASE T The LAN has two indicators See Chapter 4 Operating Basics for details This indicator glows green when the computer is connected to a LAN and the LAN is functioning properly This indicator glows orange when data is being exchanged between the computer and the LAN User s Manual 2 5 The Grand Tour Underside Figure 2 5 shows the underside of the computer Make sure the display is closed before turning over your computer Battery lock Battery pack Notches Battery za release latch eo s Slim Select Bay lock Docking Interface Slim Select Bay lock screw Memory module cover Slim Select Bay HDD pack cover screw Figure 2 5 The underside of the computer __n Battery lock Slide this lock to release the battery pack for removal Battery pack The battery pack powers the computer when the AC adaptor is not connected For detailed information on the battery pack refer to Chapter 6 Power and Power Up Modes Notches Notches on the computer engage hooks on the Advanced port Replicator III to hold the connection securely 3 Battery
35. a wake up signal from the LAN Enabled Enables Wake up on LAN Disabled Disables Wake up on LAN Default Do not install or remove an optional memory module while Wake up on LAN is enabled The Wake up on LAN function consumes power even when the system is off Leave the AC adaptor connected while using this feature User s Manual 7 7 HW Setup Built in LAN This feature enables or disables the Built in LAN Enabled Enables Built in LAN functions Default Disabled Disables Built in LAN functions USB USB KB Mouse Legacy Emulation Use this option to enable or disable USB KB Mouse Legacy Emulation If your operating system does not support USB you can still use a USB mouse and keyboard by setting the USB KB Mouse Legacy Emulation item to Enabled Enabled Enables the USB KB Mouse Legacy Emulation Default Disabled Disables the USB KB Mouse Legacy Emulation USB FDD Legacy Emulation Use this option to enable or disable USB FDD Legacy Emulation Enabled Enables the USB FDD Legacy Emulation Default Disabled Disables the USB FDD Legacy Emulation 7 8 User s Manual TECRA M2 Chapter 8 Optional Devices Optional devices can expand the computer s capabilities and its versatility This chapter describes connection or installation of the following devices which are available from your TOSHIBA dealer Cards memory B PC cards B SD cards B Memory expansion Power devices m Additional bat
36. a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions To avoid risk of lost data always make back up copies of data by periodically storing it on an external storage medium For optimum performance use your computer product only under recommended conditions Read additional restrictions under Environmental Conditions in your product Resource Guide Contact TOSHIBA Service and Support for more information cre gm D xxvi User s Manual TECRA M2 Chapter 1 Introduction This chapter provides an equipment checklist and it identifies the computer s features options and accessories AR Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA Equipment checklist Carefully unpack your computer Save the box and packing materials for future use Hardware Check to make sure you have all the following items User s Manual TECRA M2 Portable Personal Computer Universal AC adaptor and power cord USB floppy disk drive Provided with some models Spare AccuPoint pointing device caps Slim Select Bay weight saver module Introduction Software E The following software is preinstalled Microsoft amp Windows XP Professional Microsoft Internet Explorer Modem driver Display Drivers for Windows TOSHIBA Utilities Wireless LAN driver Bluetooth
37. al v Figure 5 2 The numeric keypad overlay User s Manual 5 7 The Keyboard Temporarily using normal keyboard overlay on While using the overlay you can temporarily access the normal keyboard without turning off the overlay 1 Hold Fn and press any other key All keys will operate as ifthe overlay were off 2 Type upper case characters by holding Fn Shift and pressing a character key 3 Release Fn to continue using the overlay Temporarily using overlay overlay off While using the normal keyboard you can temporarily use the keypad overlay without turning it on 1 Press and hold down Fn 2 Check the keyboard indicators Pressing Fn turns on the most recently used overlay Ifthe Numeric mode indicator lights you can use the overlay for numeric entry Ifthe Arrow mode indicator lights you can use the overlay for cursor and page control 3 Release Fn to return to normal keyboard operation Temporarily changing modes If the computer is in Numeric mode you can switch temporarily to Arrow mode by pressing a shift key If the computer is in Arrow mode you can switch temporarily to Numeric mode by pressing a shift key Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation But you can generate these characters using their ASCII codes With the overlay on 1 Hold down Alt 2 U
38. and Modes Table 2 Video modes XGA continued Resolution 640 x 480 800 x 600 1024 x 768 1280 x 1024 1600 x 1200 1920 x 1440 2048 x 1536 LCD colors 64K 64K 64K 64K 64K 64K 64K 64K Virtual 64K 64K Virtual 64K 64K Virtual 64K 64K Virtual CRT colors 64K 64K 64K 64K 64K 64K 64K 64K 64K 64K 64K 64K 64K 64K Vertical frequency Hz 60 75 85 100 60 75 85 100 60 75 85 100 60 75 85 100 60 75 85 100 60 75 85 60 75 Some SVGA modes are not supported at LCD CRT simultaneous mode and LCD CRT Multi Monitor mode User s Manual B 5 Display Controller and Modes Table 2 Video modes XGA continued Resolution 640 x 480 800 x 600 1024 x 768 1280 x 1024 1600 x 1200 1920 x 1440 2048 x 1536 LCD colors 16M 16M 16M 16M 16M 16M 16M 16M Virtual 16M 16M Virtual 16M 16M Virtual 16M 16M Virtual CRT colors 16M 16M 16M 16M 16M 16M 16M 16M 16M 16M 16M 16M 16M 16M Vertical frequency Hz 60 75 85 100 60 75 85 100 60 75 85 100 60 75 85 100 60 75 85 100 60 75 60 75 Some SVGA modes are not supported at LCD CRT simultaneous mode and LCD CRT Multi Monitor mode B 6 User s Manual Display Controller and Modes Table 3 Video modes SXGA Resolution 640 x 480 800 x 600 1024 x 768 1280 x 1024
39. check the configuration in Windows to make sure it is appropriate for your card Removing a PC card To remove the PC card follow the steps below 1 Open the Safety Remove Hardware icon on the system tray and disable the PC card 2 Press the PC card eject button to extend it 3 Press the extended eject button to pop the card out slightly 8 2 User s Manual Optional Devices 4 Pinch the PC card and draw it out Eject Button Figure 8 2 Removing the PC card SD cards i The computer is equipped with an SD card slot that can accommodate Secure Digital flash memory cards with various memory capacities SD cards let you easily transfer data from devices such as digital cameras and Personal Digital Assistants that use SD card flash memory The cards have a high level of security and copy protection features The slot cannot accommodate Multi Media cards Keep foreign objects out of the SD card slot A pin or similar object can damage the computer s circuitry SD memory cards comply with SDMI Secure Digital Music Initiative which is a technology adopted to prevent unlawful copy or playback of digital music For this reason you cannot copy or playback protected material on another computer or other device You may not use the reproduction of any copyrighted material except for your personal enjoyment Formatting an SD card SD memory cards are sold with format in conformity to the Standards of SD memory
40. circular direction around the CD DVD If necessary use a cloth dampened in water or a neutral cleaner Do not use benzine thinner or similar cleaner Floppy disks 1 Store your floppy disks in the container they came in to protect them and keep them clean If a floppy disk is dirty do not use cleaning fluid Clean it with a soft damp cloth Do not slide back the floppy disk s protective metal covering or touch the floppy disk s magnetic surface Fingerprints may prevent the floppy disk drive from reading data from the floppy disk Data may be lost if the floppy disk is twisted bent or exposed to direct sunlight extreme heat or cold Do not place heavy objects on your floppy disks Do not eat smoke or use erasers near your floppy disks Foreign particles inside the floppy disk s jacket can damage the magnetic surface Magnetic energy can destroy the data on your floppy disks Keep your floppy disks away from speakers radios television sets and other sources of magnetic fields User s Manual 4 17 Operating Basics Sound System Using the microphone Your computer has a built in microphone that can be used to record monaural sounds into your applications It can also be used to issue voice commands to applications that support such functions Since your computer has a built in microphone and speaker howling may be heard under certain conditions Howling occurs when sound from the speaker is picked u
41. dealer 9 12 User s Manual Troubleshooting SD card Refer also to Chapter 8 Optional Devices Problem Procedure SD card error occurs Reseat the SD card to make sure it is firmly connected Check the card s documentation You cannot write toan Make sure the card is not write protected SD card You cannot read a file Make sure the target file is on the SD Card inserted in the slot If problems persist contact your dealer PC card Refer also to Chapter 8 Optional Devices Problem Procedure PC card error occurs Reseat the PC card to make sure it is firmly connected Make sure the connection between the external device and the card is firm Check the card s documentation If problems persist contact your dealer Infrared port Refer also to the documentation for your IrDA compatible device and related software Problem Procedure Infrared devices do Make sure there is no obstruction blocking not work as expected communication between the computer and the target device If problems persist contact your dealer User s Manual 9 13 Troubleshooting TOSHIBA Dual Pointing Device If you are using a USB mouse also refer to the USB section in this chapter and to your mouse documentation Touch Pad AccuPoint Problem Either the Touch Pad or the AccuPoint does not work On screen pointer does not respond to Pad operation The mouse pointer moves too fast or too slow Doub
42. ee eee 6 7 Safety precautions 2 0 eee 6 7 Charging the batteries llli 6 9 Monitoring battery capacity 2222220 6 11 Maximizing battery operating time 005 6 11 Retaining data with power off 2 llle 6 12 Extending battery life llle 6 12 Replacing the battery pack llll sl 6 13 Removing the battery pack lesse 6 13 Installing the battery pack illis 6 14 TOSHIBA Password Utility 0 0 cee eee 6 15 User password iscir iarri cect eh 6 15 Supervisor password 1 0 0 0 cee ee 6 17 Starting the computer by password 0000 ee ee eee 6 17 xvi User s Manual Table of Contents Power up modes HH 2nn neun nun 6 18 Windows utilities lll BAR 6 18 Hot keys terieleWixmentuee e ge RP DEED Ede SE a 6 18 Panel power on off llllllllelleleeeeleeeen 6 18 System Auto Off occi secs el ak n eee ae ee 6 18 Chapter 7 HW Setup Accessing HW Setup 0 0 cece eee eee eee eee 7 1 HW Setup window sonen nennen nennen 7 1 Chapter 8 Optional Devices PC cards eros a Sead ala 8 2 Inserting a PC card 0 0 0 cc nenn 8 2 Removing a PCcard 2 222er cee ee eee 8 2 SD cards 2 wees ana a a a ee 8 3 Formatting an SD card 22220 n seen rennen nn 8 3 Installing an SD card 0 0000 cee 8 4 Removing an SD Card 0 00 eee 8 4 S
43. free environment for holding mutual communication via the Internet Protocol or Local Area Network Refer to the Sound system section in Chapter 4 Operating Basics for details This utility let you rotate the desktop by 0 and 180 easily it can rotate by clicking the icon in a taskbar In a multi monitor setup only the LCD of this function is effective You can add a number of options to make your computer even more powerful and convenient to use The following options are available Memory expansion Battery pack High Capacity Battery pack AC adaptor Battery charger A 256 512 or 1 024 MB memory module PC2100 PC2700 DDR can easily be installed in the computer An additional battery pack can be purchased from your TOSHIBA dealer Use it as a spare or replacement An additional battery pack can be purchased from your TOSHIBA dealer Use it as a spare or replacement If you use your computer at more than one site frequently it may be convenient to purchase an additional AC adaptor for each site so you will not have to carry the adaptor with you The battery charger lets you charge extra batteries outside the computer User s Manual Introduction Security lock USB floppy disk Kit Advanced Port Replicator Ill Hard disk drive Wireless LAN Kit Bluetooth Kit A slot is available to attach a security cable to the computer to deter theft A 3 1 2 floppy disk drive accommodates 1 44 me
44. is also impacted due to obstacles in the signal path of the radio that may either absorb or reflect the radio signal Supported Frequency Sub bands Subject to the radio regulations that apply in the countries regions your Wireless LAN card may support a different set of 5GHz 2 4GHz channels Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries regions Wireless IEEE 802 11 Channels Sets Revision B and G Frequency Range 2400 2483 5 MHz Channel ID 1 2412 2 2417 3 2422 4 2427 5 2432 6 2437 7 2442 8 2447 9 2452 G 2 User s Manual Wireless LAN 10 2457 1 11 2462 12 2467 2 13 2472 2 1 Factory set default channels 2 Refer to the sheet Approved Countries Regions for use for the countries regions that in which these channels can be used When installing Wireless LAN cards the channel configuration is managed as follows WB For wireless clients that operate in a Wireless LAN Infrastructure the Wireless LAN card will automatically start operation atthe channel identified by the Wireless LAN Access Point When roaming between different access points the station can dynamically switch to another channel if required W For Wireless LAN cards installed in Wireless clients that operating in a peer to peer mode the card will use the default channel 10 B n a Wireless LAN Access Point the Wireless LAN card will use the factory set
45. is payable where an assessment is based on reports against non Telecom New Zealand Specifications 112 50 is charged for each variation when submitted at the same time as the original An invoice for NZ1237 50 will be sent under separate cover Description on Laser specification The optical drive such as DVD ROM drive DVD CD RW drive and DVD Multi drive and DVD R RW drive that is used in this computer is equipped with laser The classification label with the following sentence is affixed to the surface of the drive CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE APPAREIL A LASER DE CLASSE 1 KLASS 1 LASER APPARAT The drive with the above label is certified by the manufacturer that the drive complies with the requirement for laser product on the date of manufacturing pursuant to article 21 of Code of Federal Regulations by the United States of America Department of Health amp Human Services Food and Drug Administration In other countries the drive is certified to comply with the requirement pursuant to IEC 825 and EN60825 on class 1 laser product This computer is equipped with the optical drive in the following list according to the model Manufacturer Type HITACHI GDR 8082N TEAC DW 224E Panasonic Communications UJDA750 HITACHI GCC 4241N Panasonic Communications UJ 811B TEAC DV W22bE Pioneer DVR K12D User s Manual Xi User s Manual xii User s Manual TECRA M2 Table of Contents P
46. meh rae Rd 9 17 Modem 4 55 pr Eee thie ERU Prisha eid Pes ee Ru o e 9 17 LAN Uo ee IPLA DER mU cua etn ee a RE 9 18 Wireless LAN nn aa Er RR CER etre nd tc Rl RSS een 9 19 BUCO o METER 9 19 Real Tire Clock wich deena ew eR eda eae oka ees 9 20 TOSHIBA support zu Heeres 9 20 Before you call ee en gen eee de een 9 20 Where to Write coes ac eee cee ansad ran DEC ee eee me Bul eae ae 9 21 xviii User s Manual Table of Contents Appendix A Specifications Appendix B Display Controller and Modes Appendix C AT Commands Appendix D S registers Appendix E V 90 Appendix F Internal Modem Guide Appendix G Wireless LAN Appendix H AC Power Cord and Connectors Appendix I Parts Numbers Glossary Index User s Manual xix Table of Contents XX User s Manual TECRA M2 Preface Congratulations on your purchase of the TECRA M2 computer This powerful notebook computer provides excellent expansion capability including multimedia devices and it is designed to provide years of reliable high performance computing This manual tells how to set up and begin using your TECRA M2 computer It also provides detailed information on configuring your computer basic operations and care using optional devices and troubleshooting If you are a new user of computers or if you re new to portable computing first read over the ntroduction and The Grand Tour chapters to familiarize yourself with the computer s features comp
47. number 13 Same as 10 I9 Returns region ID in English Result Codes OK n 0 3 9 ERROR Otherwise Monitor speaker volume This command sets speaker volume to low medium or high LO Low volume L1 Low volume Same as L0 L2 Medium volume default L3 High volume Result Codes OK n 0 1 2 3 ERROR Otherwise Monitor speaker mode This command turns the speaker on or off MO The speaker is off M1 The speaker is on until the modem detects the carrier signal default M2 The speaker is always on when modem is off hook M3 Speaker is on until the carrier is detected except when dialing Result Codes OK n 0 1 2 3 ERROR Otherwise User s Manual C 3 AT Commands Nn Modulation handshake This command controls whether or not the local modem performs a negotiated handshake at connection time with the remote modem when the communication speed of the two modems is different NO When originating or answering this is for handshake only at the communication standard specified by S37 and the ATB command N1 When originating or answering begin the handshake at the communication standard specified by S37 and the ATB command default During handshake a lower transmission speed may be selected Result Codes OK n 0 1 ERROR Otherwise On Return on line to data mode O0 Instructs the modem to exit on line command mode and return to data mode see AT escape sequence O1 This command issues a retr
48. ot go os Turn off the computer Insert one end of the cable into the computer s parallel port Tighten the screws that fasten the cable connector to the computer s parallel port Insert the other end of the cable into the printer s parallel connector Fasten the connector to the printer with the clips on the parallel port Turn on the printer Turn on the computer Start the HW Setup program Refer to Chapter 7 HW Setup Select the Parallel Printer tab from the HW Setup window Set the mode to ECP and press OK Choose Reboot for the change to take effect 8 20 User s Manual Optional Devices Security lock Security locks enable you to anchor your computer and optional Advanced Port Replicator III to a desk or other heavy object to help prevent unauthorized removal of the computer or Advanced Port Replicator III The computer has a security lock slot on the left side Attach one end of a cable to a desk and the other end to the security lock slot 1 Turn the computer so the right side faces you 2 Align the holes for the security lock and attach the lock Figure 8 25 Security lock User s Manual 8 21 Optional Devices 8 22 User s Manual TECRA M2 Chapter 9 Troubleshooting Problem User s Manual TOSHIBA designed the computer for durability However should problems occur following the procedures in this chapter can help to determine the cause All readers should become familia
49. processing memory input output functions and controlling other chips CMOS Complementary Metal Oxide Semiconductor An electronic circuit fabricated on a silicon wafer that requires very little power Integrated circuits implemented in CMOS technology can be tightly packaged and are highly reliable cold start Starting a computer that is currently off turning on the power COM COM2 COM3 and COM4 The names assigned to the serial and communication ports commands Instructions you enter at the terminal keyboard that direct the actions of the computer or its peripheral devices communications The means by which a computer transmits and receives data to and from another computer or device See parallel interface serial interface Glossary 4 User s Manual Glossary compatibility 1 The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred 2 the ability of one device to connect to or communicate with another system or component components Elements or parts of a system which make up the whole system computer program A set of instructions written for a computer that enable itto achieve a desired result computer system A combination of hardware software firmware and peripheral components assembled to process data into useful information configuration The specific components in your system s
50. release Slide and hold this latch to release the battery im i latch pack for removal For detailed information on removing the battery packs refer to Chapter 6 Power and Power Up Modes Docking interface This port enables connection of an optional Advanced port Replicator Ill described in Chapter 8 Optional Devices 2 6 User s Manual The Grand Tour x G oO amp tl Keep foreign objects out of the docking interface port A pin or similar object can damage the computer s circuitry A plastic shutter protects the connector Memory module This cover protects one memory module sockets cover one or no module is preinstalled Another memory module is under the keyboard Refer to the Memory expansion section in Chapter 8 Optional Devices Slim Select Bay lock Slide the lock to release or secure the Slim Select Bay ejector Be sure to lock the Slim Select Bay lock before you transport or carry the computer HDD pack cover One screw secures the HDD cover screw Slim Select Bay See the Right side section in this chapter for details Slim Select Bay lock One screw secures the Slim Select Bay lock screw User s Manual 2 7 The Grand Tour Front with the display open This section shows the computer with the display open Refer to the appropriate illustration for details Microphone Display hinge Display screen LCD Sensor switch Not shown Stereo speaker Left St
51. that can be displayed on screen Software written for a given video mode will run on any computer that supports the mode The computer s display controller supports all VGA and SVGA modes the most widely used industry standards Video modes The computer supports video modes defined in the tables below If your application offers a selection of mode numbers that do not match the numbers on the table select a mode based on mode type resolution character matrix number of colors and refresh rates Also if your software supports both graphics and text modes the screen display may appear to operate faster using a text mode User s Manual Display Controller and Modes Video mode 0 1 2 3 0 1 2 3 O 1 2 3 4 5 7 Table1 Video modes VGA Type Resolution Character VGA Text VGA Text VGA Text VGA Text VGA Text VGA Text VGA Grph VGA Grph VGA Text VGA Text 40 x 25 Characters 80 x 25 Characters 40 x 25 Characters 80 x 25 Characters 40 x 25 Characters 80 x 25 Characters 320 x 200 Pels 640 x 200 Pels 80 x 25 Characters 80 x 25 Characters matrix pels 8x8 8x8 8 x 14 8x14 9 x 16 9 x 16 8x8 8x8 9 x 14 9 x 16 LCD colors 16 of 256K 16 of 256K 16 of 256K 16 of 256K 16 of 256K 16 of 256K 4 of 256K 2 of 256K Mono Mono CRT colors 16 of 256K 16 of 256K 16 of
52. the Telecom line during electrical storms W When relocating the equipment always disconnect the Telecom line connection before the power connection and reconnect the power first W This equipment may not be compatible with Telecom Distinctive Alert cadences and services such as FaxAbility NOTE THAT FAULT CALLOUTS CAUSED BY ANY OF THE ABOVE CAUSES MAY INCUR A CHARGE FROM TELECOM General conditions As required by PTC 100 please ensure that this office is advised of any changes to the specifications of these products which might affect compliance with the relevant PTC Specifications The grant of this Telepermit is specific to the above products with the marketing description as stated on the Telepermit label artwork The Telepermit may not be assigned to other parties or other products without Telecom approval A Telepermit artwork for each device is included from which you may prepare any number of Telepermit labels subject to the general instructions on format size and colour on the attached sheet The Telepermit label must be displayed on the product at all times as proof to purchasers and service personnel that the product is able to be legitimately connected to the Telecom network User s Manual User s Manual The Telepermit label may also be shown on the packaging of the product and in the sales literature as required in PTC 100 The charge for a Telepermit assessment is 337 50 An additional charge of 337 50
53. the Profile item in TOSHIBA Power Saver This feature turns power to the computer off when the display panel is closed and turns it back on when the panel is opened You can specify the setting in the When I close the lid item of the Setup Action tab in TOSHIBA Power Saver When battery power is exhausted to the point that computer operation cannot be continued the system automatically enters Hibernation and shuts down You can specify the setting in the Setup Action tab in TOSHIBA Power Saver User s Manual Introduction Heat dispersal Hibernation Standby To protect from overheating the CPU has an internal temperature sensor Ifthe computer s internal temperature rises to a certain level the cooling fan is turned on or the processing speed is lowered Use the Fan item of the Basic Setup tab in TOSHIBA Power Saver B Maximum Turns on fan first Performance then if necessary lowers CPU processing speed B Performance Uses a combination of fan and lowering the CPU processing speed W Battery optimized Lowers the CPU processing speed first then if necessary turns on the fan This feature lets you turn off the power without exiting from your software The contents of main memory are saved to the hard disk when you turn on the power again you can continue working right where you left off Refer to the Turning off the power section in Chapter 3 Getting Started for details If you have to interrupt
54. the drive you may lose data or damage the floppy disk or the drive 2 Click the Safety Remove Hardware icon on the Task Bar 3 Click floppy disk drive 4 Pull the floppy disk drive connector out of the USB port Changing Slim Select Bay modules N i This section explains how to change modules in the Slim Select Bay The illustrations show replacement of the DVD ROM drive with the Slim Select Bay HDD adaptor Therefore the text refers to those modules However the procedures are the same for any of the modules DVD ROM drive CD RW DVD ROM drive DVD Multi drive DVD R RW drive HDD adaptor Slim Select Bay 2nd battery pack with separate tray or weight saver E To avoid injury do not put your hand into the Slim Select Bay slot W Before removing or inserting a second battery pack turn off the computer s power The TOSHIBA Mobile Extension is preinstalled to support hot swapping under Windows Refer to Chapter 1 Introduction for information on using this utility to change modules while the computer s power is on Removing a module AN Remove the DVD ROM drive as described below 1 Check all disk indicators to make sure no disks are operating 2 Turn the computer upside down Wait for all disk indicators to go out before you turn over the computer and do not lay the computer down gently Shock can damage the HDD or other components 3 Remove the screw near the icon securing the Slim Select Bay 4 Make sure
55. the priority for booting the computer Select from the following settings HDD gt FDD gt CD ROM gt LAN FDD HDD gt CD ROM gt LAN HDD gt CD ROM gt LAN gt FDD FDD gt CD ROM gt LAN HDD CD ROM LAN HDD gt FDD CD ROM gt LAN FDD gt HDD The computer looks for bootable files in the following order HDD floppy disk drive 1 CD ROM 2 and LAN Default The computer looks for bootable files in the following order floppy disk drive t HDD CD ROM 2 and LAN The computer looks for bootable files in the following order HDD CD ROM 2 LAN and floppy disk drive The computer looks for bootable files in the following order floppy disk drive CD ROM 2 LAN and HDD The computer looks for bootable files in the following order CD ROM 2 LAN HDD floppy disk drive The computer looks for bootable files in the following order CD ROM 2 LAN floppy disk drive t and HDD You can override the settings and manually select a boot device by pressing one of the following keys while the computer is booting U N 1 2 P C Selects the USB floppy disk drive Selects the Network Selects the primary HDD Selects the secondary HDD Selects the PC card HDD Selects the CD ROM FDD is looked for when the boot disk is contained in external FDD When SD memory card is set as the boot disk external FDD is looked for first Next SD memory card is lo
56. timer also specifies the wait for silence time for the dial modifier in seconds S7 is not associated with the W dial modifier Range 1 255 Default 50 Units seconds User s Manual D 3 S registers Comma pause time This register sets the time in seconds that the modem must pause when it encounters a comma in the dial command string In some countries regions S8 will set both wait before dialing and comma pause time Range 0 255 Default 2 Units seconds S11 DTMF dialing speed This register determines the dialing speed which is prefixed for each country region Range 50 255 Default 95 Units 001 seconds 12 Escape guard time This register sets the value in 20 millisecond increments for the required pause after the escape sequence Range 0 255 Default 50 Units 02 seconds D 4 User s Manual S registers S37 Dial line rate S37 0 default maximum modem speed S37 21 reserved 37 2 1200 75 bps 37 3 300 bps 37 4 reserved 37 5 1200 bps 37 6 2400 bps 37 7 4800 bps 37 8 7200 bps 37 9 9600 bps 37 10 12000 bps 37 11 14400 bps 37 12 16800 bps 37 13 19200 bps 37 14 21600 bps 37 15 24000 bps S37 16 26400 bps 37 17 28800 bps 37 18 31200 bps 37 19 33600 bps User s Manual D 5 S registers AT command set result codes The following table shows the result codes The result code summary Result Code Numeric OK 0
57. to use Dialing Properties Select this item to display the dialing properties If you are using the computer in Japan the Telecommunications Business Law requires that you select Japan region mode It is illegal to use the modem in Japan with any other selection 4 20 User s Manual Operating Basics Connecting To connect the modem cable follow the steps below The modular cable that comes with the computer must be used to connect a modem Connect the end ofthe modular cable with the core to the computer WN E ncase ofa lightning storm unplug the modem cable from the telephone jack W Do not connect the modem to a digital telephone line A digital line will damage the modem 1 Plug one end of the modular cable into the modem jack 2 Plug the other end of the modular cable into a telephone jack Figure 4 12 Connecting the internal modem AR Do not pull on the cable or move the computer while the cable is connected 7 If you use a storage device such as an optical drive or HDD connected to a 1 16 bit PC card you might experience the following modem problems W Modem speed is slow or communication is interrupted E Skips may occur in sound Disconnecting To disconnect the internal modem cable follow the steps below 1 Pinch the lever on the connector in the telephone jack and pull out the connector 2 Disconnect the cable from the computer in the same manner 3 In the same way pul
58. values amp F Recall factory setting as active configuration V 22bis guard tone control This command determines which guard tone if any to transmit while transmitting in the high band answer mode This command is only used in V 22 and V 22bis mode This option is not used in North America and is for international use only amp G0 Guard tone disabled default amp G1 Sets guard tone to 550 Hz amp G2 Sets guard tone to 1800 Hz Result Codes OK n 0 1 2 ERROR Otherwise Local flow control selection amp KO Disable flow control amp K3 Enable CTS RTS flow control default amp K4 Enable XON XOFF flow control Result Codes OK n 0 3 4 ERROR Otherwise Select Pulse Dial Make Break Ratio WW amp PO Selects 39 61 make break ratio at 10 pulses per second amp P1 Selects 33 67 make break ratio at 10 pulses per second amp P2 Selects 33 67 make break ratio at 20 pulses per second Result Codes OK n 0 1 2 ERROR Otherwise User s Manual C 7 AT Commands amp Tn Self test commands These tests can help to isolate problems if you experience periodic data loss or random errors amp TO Abort Stops any test in progress amp T1 Local analog loop This test verifies modem operation as well as the connection between the modem and computer Any data entered at the local DTE is modulated then demodulated and returned to the local DTE To work properly the modem must be off line
59. your work you can turn off the power without exiting from your software Data is maintained in the computer s main memory When you turn on the power again you can continue working right where you left off User s Manual Introduction Utilities This section describes preinstalled utilities and tells how to start them For details on operations refer to each utility s online manual help files or readme txt files TOSHIBA Power Saver HW Setup TOSHIBA Controls Fn esse DVD Video Player Bluetooth TOSHIBA Stack installed To access this power savings management program click the Control Panel and select the TOSHIBA Power Saver icon This program lets you customize your hardware settings according to the way you work with your computer and the peripherals you use To start the utility click the Windows Start button and click Control Panel In the Control Panel select the TOSHIBA HW Setup icon This utility have a section to let you do the following E Buttons Assign applications to the Internet button default setting is the browser and to the TOSHIBA Console button default setting is the TOSHIBA Console This Windows program lets you define your own shortcut keys to quickly launch applications and speed your work in Windows To start the utility click the Windows Start button point to All Programs point to TOSHIBA point to Utilities and click Fn esse The DVD Video Player is used to
60. 0 7200 9600 12000 14400 16800 19200 21600 24000 26400 28800 31200 3600 bp Data reception only with V 90 28000 29333 30666 32000 33333 34666 36000 37333 38666 40000 41333 42666 44000 45333 46666 48000 49333 50666 52000 53333 54666 56000 bps Fax 2400 4800 7200 9600 12000 14400 bps 10 dBm 10 to 40 dBm 600 ohms 30 MNP class 4 and ITU T V 42 MNP class 5 and ITU T V 42bis 3 3V supplied by computer User s Manual A 3 Specifications A 4 User s Manual TECRA M2 Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off The controller is an advanced Video Graphics Array VGA that provides Super VGA SVGA and Extended Graphics Array XGA Super Extended Graphics Array SXGA Super Extended Graphics Array plus SXGA support for the internal LCD and external monitors Two models are available W 14 1 XGA 1024 horizontal x 768 vertical pixels E 14 1 SXGA 1400 horizontal x 1050 vertical pixels Because of the LCD s increased resolution lines may appear broken in DOS mode IQ A high resolution external monitor connected to the computer can display up to 2048 horizontal and 1536 vertical pixels at up to 16M colors The display controller also controls the video mode which uses industry standard rules to govern the screen resolution and the maximum number of colors
61. 000 EU Declaration of Conformity TOSHIBA declares that the product PTM20 conforms to the following Standards Supplementary The product complies with the requirements of Information the Low Voltage Directive 73 23 EEC the EMC Directive 89 336 EEC and or the R amp TTE Directive 1999 05 EEC This product is carrying the CE Mark in accordance with the related European Directives Responsible for CE Marking is TOSHIBA Europe Hammfelddamm 8 41460 Neuss Germany VCCI Class B Information CORB FRUEREFERBFEB FH HER VCC DH I amp 22ABIBx EIC COREL KERRATA OTE ZENELTLIEFH CORESI TETLEY a VREET ASSOC REBELZIER TFLENBUETF BREITE CIEUUBUSRUEUCTFSU Modem warning notice Conformity Statement The equipment has been approved to Commission Decision CTR21 for pan European single terminal connection to the Public Switched Telephone Network PSTN However due to differences between the individual PSTNs provided in different countries regions the approval does not of itself give an unconditional assurance of successful operation on every PSTN network termination point In the event of problems you should contact your equipment supplier in the first instance User s Manual User s Manual Network Compatibility Statement This product is designed to work with and is compatible with the following networks It has been tested to and found to conform with the additional requirements conditional i
62. 2 mouse and PS 2 keyboard The Port Replicator connects directly to the docking interface on the bottom of the computer The AC adaptor connects the Port Replicator to a power source The computer must be configured properly before connecting to a LAN Logging onto a LAN using the computer s default settings could cause a malfunction in LAN operation Check with your LAN administrator regarding set up procedures E You must connect the AC adaptor before you connect to a Advanced Port Replicator III E Priority is given to DVI port over CRT if DVI and CRT are connected simultaneously User s Manual 8 19 Optional Devices The following ports and accessories are available on the Advanced Port Replicator III RJ45 LAN jack RJ11 Modem jack External monitor port Parallel port Serial port PS 2 mouse port PS 2 keyboard port DC IN 15V socket Security lock slot Audio line in line out jacks Universal Serial Bus four IEEE 1394 port DVI port Parallel printer You can connect any standard Centronics compatible parallel printer to your computer All you need is an IBM PC parallel printer cable Your dealer can supply one or you can purchase one at most computer stores The cable s connectors are designed so that it is impossible for you to connect them incorrectly You can also connect a parallel printer to an optional Advanced Port Replicator III To connect a printer follow these steps 1 2 3 DB
63. 201206 Singapore TOSHIBA Singapore Pte Ltd 438B Alexandra Road 06 01 Alexandra Technopark Singapore 119968 In Europe Germany amp Austria TOSHIBA Europe l E GmbH Gesch ftsbereich Deutschland sterreich Hammfelddamm 8 D 41460 Neuss Germany France TOSHIBA Systems France S A 7 Rue Ampere B P 131 92804 Puteaux Cedex Netherlands TOSHIBA Information Systems Benelux B V Rivium Boulevard 41 2909 LK Capelle a d IJssel Spain TOSHIBA Information Systems ESPANA Parque Empresarial San Fernando Edificio Europa I Planta Escalera A 28830 Madrid 9 21 Troubleshooting Outside of Europe United States of America TOSHIBA America Information Systems Inc 9740 Irvine Boulevard Irvine California 92618 USA In Europe United Kingdom TOSHIBA Information Systems U K Ltd TOSHIBA Court Weybridge Business Park Addlestone Road Weybridge Surrey KT15 2UL The Rest of Europe TOSHIBA Europe l E GmbH Gesch ftsbereich Deutschland sterreich Hammfelddamm 8 D 41460 Neuss Germany 9 22 User s Manual TECRA M2 Appendix A Specifications This appendix summarizes the computer s technical specifications Physical Dimensions Weight typical 2 26 kilograms configured with 14 XGA 256MB RAM 40GB HDD DVD ROM drive modem LAN 100M Bit Wireless LAN 6cell battery Weight will vary with other configurations Above weights are measured at a specific crite
64. 2nd battery indicator refers to the Slim Select Bay indicator when a D SS 1 secondary battery is installed 1 When the 2nd battery is not charging 2 When the main battery is not charging 3 For the computer to shut down in hibernation mode the hibernation feature must be enabled in two places in TOSHIBA Power Saver the Hibernate window and the Battery Alarm item of the Alarm window If a main battery and a 2nd battery are installed the computer does not shut down until the charge in both batteries is exhausted 4 When no 2nd battery is installed s When no main battery is installed When batteries are charged the main battery is charged first When it is l fully charged the 2nd battery is charged User s Manual 6 3 Power and Power Up Modes Power indicators As shown in the above table the Battery Slim Select Bay DC IN 15V and Power indicators on the system indicator alert you to the computer s operating capability and battery charge status Battery indicators Check the Battery indicator to determine the status of the main battery and the Slim Select Bay indicator to determine the status of the secondary battery The following indicator lights indicate the battery status Flashing orange The battery charge is low The AC adaptor must be connected to recharge the battery Orange Indicates the AC adaptor is connected and charging the battery Green Indicates the AC adaptor is connected and the batte
65. 6 display brightness 5 5 Fn F7 display brightness 5 5 Fn F8 wireless setting 5 5 Fn F9 Dual Pointing Device 5 5 Fn F10 arrow mode 5 3 Fn F11 numeric mode 5 3 Fn F12 ScrLock 5 3 Fn Space display resolution selection 5 6 Function keys 5 2 G Graphics controller 1 6 Hard disk drive 1 4 1 16 automatic power off 1 11 Installing 8 13 problems 9 7 Removing 8 12 Headphone jack See Sound system Heat dispersal 1 12 4 27 Hibernation 1 12 5 4 High Capacity Battery 1 15 6 6 Hot keys 1 10 display brightness decrease 5 5 display brightness increase 5 5 display selection 5 4 hibernation 5 4 instant security 5 4 power save mode 5 4 standby 5 4 wireless setting 5 5 sound mute 5 3 HW Setup 1 13 Index 2 User s Manual Index accessing 7 1 boot priority 7 4 CPU 7 3 device config 7 2 display 7 2 general 7 2 keyboard 7 7 LAN 7 7 parallel printer 7 2 USB 7 8 window 7 1 i LINK 1 7 2 2 8 19 connecting 8 18 disconnecting 8 19 precautions 8 18 problems 9 17 Indicators 2 10 6 4 Infrared port 1 7 location 2 1 problems 9 13 Instant security See Hot keys Interfaces See Ports K Keyboard 1 6 5 1 emulating enhanced key board 5 2 F1 F12 function keys 5 2 Fn Sticky key 5 6 hot keys 5 3 problems 9 7 typewriter keys 5 1 Windows special keys 5 6 Keypad overlay 1 11 5 7 arrow mode 5 7 numeric mode 5 7 temporarily using normal keyboard overlay on 5 8 te
66. A Collision Avoidance with Acknowledg ment ACK Protocol m 54 48 36 24 18 12 9 6 Mb s Revision A and G Revision A B B G A B G combo type m 11 5 5 2 1 Mb s Revision B m 108 96 72 48 36 24 18 12 Mb s Turbo Mode Revision A B G combo type Data Rate Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to E Country region where the product was purchased B Type of product Wireless communication is often subject to local radio regulations Although Wireless LAN wireless networking products have been designed for operation in the license free 2 4GHz and 5GHz band local radio regulations may impose a number of limitations to the use of wireless communication equipment Refer to the sheet Information to the User for regulatory information that may apply in your country region 1 User s Manual Wireless LAN R F Frequency W Band 5GHz 5150 5850 MHz Revision A Turbo Mode m Band2 4GHz 2400 2483 5 MHz Revision B G Modulation B DSSS CCK DSSS DQPSK DSSS DBPSK Technique Revision B BW OFDM BPSK OFDM QPSK OFDM 16QAM OFDM 64QAM Revision A G Turbo Mode The range of the wireless signal is related to the Transmit Rate of the wireless communication Communications at lower Transmit range may travel larger distances E The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high density materials W Range
67. A B G combo type W Frequency Channel Selection 5 GHz Revision A 2 4 GHz Revision B G B Roaming over multiple channels Card Power Management W Wired Equivalent Privacy WEP data encryption based on 152 bit encryption algorithm Revision B G A B G combo type Wired Equivalent Privacy WEP data encryption based on 128 bit encryption algorithm Revision A B combo B only type E Advanced Encryption Standard AES data encryption based on 256 bit encryption algorithm Revision B G A B G combotype Slim Select Bay is a single drive bay that accommodates a DVD ROM drive CD RW DVD ROM drive DVD Multi drive DVD R RW drive secondary hard disk drive or secondary battery pack The TOSHIBA Mobile Extension enables hot insertion of modules when you are using a plug and play operating system To reduce weight the Slim Select Bay module can be removed and a weight saver installed User s Manual 1 9 Introduction Security Security lock slot Slim Select Bay lock Software Operating System TOSHIBA Utilities Plug and Play Special features Connects an optional security lock to anchor the computer to a desk or other large object Slim Select Bay module can be secured by Slim Select Bay lock fixed with a lock screw in the lock position The lock screw is inserted in the unlock position when purchased Windows XP Professional operating system and TOSHIBA Utilities and drivers preinstalled on t
68. Byte compare 3 Click the OK button The Record and Verify function automatically checks whether data has been correctly recorded onto a CD DVD Byte compare compares the original data file with the data recorded on the CD DVD and checks that the data completely matches User s Manual 4 15 Operating Basics Video DVD R RW RAM As for InterVideo WinDVD Creater2 Platinum Only the model that can be written in to DVD is attached Note the following limitations when you write video to DVD When installing uninstalling or InterVideo WinDVD Creator 2 Platinum the computer should be set to system administrator or equivalent privilege When Drag n Drop or similar software is resident in the computer s memory the DVD Multi drive locks In this situation other software cannot be used to write data to the disc While you are editing DVD R RW RAM you can display previews However if an application other than WinDVD is running the preview might not display properly To ensure proper display of previews do not start other applications while you are editing DVD R RW RAM disc Do not change the resolution or the number of screen colors while InterVideo WinDVD Creator 2 Platinum is running Although the online manual and Help files indicate that JPEG files can be used in fact they cannot be used InterVideo WinDVD Creator 2 Platinum cannot make DVD Audio VideoCD and miniDVD DVD R RW discs cannot be written in VR form
69. CONNECT 1 RING 2 NO CARRIER 3 ERROR 4 CONNECT 1200 EC 5 NO DIAL TONE 6 BUSY 7 NO ANSWER 8 CONNECT 2400 EC 10 CONNECT 4800 EC 11 CONNECT 9600 EC 12 CONNECT 14400 EC 13 CONNECT 19200 EC 14 CONNECT 7200 EC 24 CONNECT 12000 EC 25 CONNECT 16800 EC 86 CONNECT 300 EC 40 CONNECT 21600 EC 55 CONNECT 24000 EC 56 CONNECT 26400 EC 57 CONNECT 28800 EC 58 CONNECT 31200 EC 59 Description Command executed Modem connected to line A ring signal has been detected Modem lost carrier signal or does not detect carrier signal or does not detect answer tone Invalid command Connection at 1200 bps No dial tone detected Busy signal detected No quiet answer Connection at 2400 bps Connection at 4800 bps Connection at 9600 bps Connection at 14400 bps Connection at 19200 bps Connection at 7200 bps Connection at 12000 bps Connection at 16800 bps Connection at 300 bps Connection at 21600 bps Connection at 24000 bps Connection at 26400 bps Connection at 28800 bps Connection at 31200 bps D 6 User s Manual S registers CONNECT 33600 EC 60 DELAYED 88 BLACKLISTED 89 BLACKLIST FULL 2 90 Connection at 33600 bps Delay is in effect for the dialed number Dialed number is blacklisted Blacklist is full 1 EC only appears when the Extended Result Codes configuration option is enabled EC is replaced by one of the following symbols depending upon the error control method used V 42bi
70. D R DVD RW CD ROM CD DA CD Text Photo CD single multi session CD ROM Mode 1 Mode 2 CD ROM XA Mode 2 Form1 Form2 Enhanced CD CD EXTRA CD G Audio CD only Addressing Method 2 Check the region code on the DVD It must match that on the DVD R RW drive Region codes are listed in the Optical media section in Chapter 2 The Grand Tour If you have trouble writing make sure you are observing the following precautions Wi Use only media recommended by TOSHIBA E Do not use the mouse or keyboard duringwriting E Use only the software supplied with the computer for recording E Do not run or start other software during writing E Do not jar the computer during writing W Do not connect disconnect external devices or install remove internal cards during writing If problems persist contact your dealer For more information refer to Chapter 4 Operating Basics Problem Drive does not operate Some programs run correctly but others do not You cannot access the external 3 1 2 floppy disk drive Procedure There may be a faulty cable connection Check the connection to the computer and to the drive The software or hardware configuration may be causing a problem Make sure the hardwareconfiguration matches your software needs Try another floppy disk If you can access the floppy disk the original floppy disk not the drive is probably causing the problem If problems persist contact your
71. Dic rd cAre oo spe h ee e hee en baie 8 5 Creation of a boot disk 2 0 0 eee ee 8 5 Memory expansion 0 0 cece eee eee 8 5 Installing memory module Main memory 22222222202 8 6 Removing memory module Main memory 8 9 Installing memory module 2nd memory 222222220 8 10 Removing memory module 2nd memory 8 11 Hard disk drive pack llllsllllslllllesles 8 12 Removing the HDD pack llllsllllellllsllles 8 12 Installing the HDD pack 0 0 0 2 cee ee 8 13 Additional battery pack 0 0 cee eee 8 13 Slim Select Bay 2nd battery pack 0 cee eee eee 8 14 Installing 4 22 deute ieie ra dea ba cite de bee 8 14 REMOVING iu uius ru ee ae Gee we ER Russ 8 14 Additional AC adaptor 200 eee eee eee 8 15 Battery charger cease ee eee a an 8 15 Slim Select Bay HDD adaptor Black sees 8 15 External monitor lseeseeeeeeeee nnn 8 16 IM hited aati eee dex n Ee RR RUE Re qe add reta dare ae 8 16 Using the TOSHIBA Console button 2222222 8 16 Changing the resolution 2 22 coneee nennen nenn 8 17 Displaying movies on a TV or CRT lesse 8 17 LLINK IEEE1394 lt poagn eed ee eben epee eet ee ez wales aa 8 18 Precautions s se aosi el Bare e ea ela eg seed ee 8 18 Connecting 2 22 4 canai cee eee ee p Te LETRA 8 18 Disconnecting 0
72. EIC T Figure 5 1 A 101 key enhanced keyboard layout The keyboard is designed to provide all the features of the 101 key enhanced keyboard shown in figure 5 1 The 101 102 key enhanced keyboard has a numeric keypad and scroll lock key It also has additional Enter and Ctrl keys to the right of the main keyboard Since the keyboard is smaller and has fewer keys some of the enhanced keyboard functions must be simulated using two keys instead of one on the larger keyboard Your software may require you to use keys that the keyboard does not have Pressing the Fn key and one of the following keys simulates the enhanced keyboard s functions 5 2 User s Manual The Keyboard ENEM EN Press Fn F10 or Fn F11 to access the integrated keypad When activated the keys with gray markings on the bottom edge become numeric keypad keys Fn F11 or cursor control keys Fn F10 Refer to the Keypad overlay section in this chapter for more information on how to operate these keys The power on default for both settings is off Ec Press Fn F12 ScrLock to lock the cursor on a specific line The power on default is off eI te Press Fn Enter to simulate Enter on the enhanced keyboard s numeric keypad Press Fn Ctrl to simulate the enhanced keyboard s right Ctrl key Hot keys Hot keys Fn a function or Esc key let you enable or disable certain features of the computers
73. HDD to the CD Do not use cut and paste The original data will be lost if there is a write error Do not perform any of the following actions Change users in the Windows XP operating system Operate the computer for any other function including use of a mouse or Touch Pad closing opening the LCD panel Start a communication application such as a modem Apply impact or vibration to the PC Install remove or connect external devices including the following PC card SD card USB devices external display i LINK devices optical digital devices Open the optical media drive If the media is poor in quality dirty or damaged writing or rewriting errors may occur Set the computer on a level surface and avoid places subject to vibration such as airplanes trains or cars Do not use an unstable surface such as a stand Keep mobile phones and other wireless communication devices away from the computer 4 10 User s Manual Operating Basics Writing CD DVDs on DVD Multi drive You can use the DVD Multi drive to write data to either CD R RW or DVD R RW RAM discs The following applications for writing are supplied on CD ROM Drag n Drop CD DVD licensed by Easy Systems Japan Ltd and DigiOn Inc InterVideo WinDVD Creator 2 Platinum which is a product of InterVideo Inc Writing CD DVDs on DVDXR RW drive DVD Dual drive You can use the DVD R RW drive to write data to either CD R RW or DVD R
74. If you suspect a problem with the battery check the DC IN 15V indicator as well as the Battery indicator For information on indicators and battery operation see Chapter 6 Power and Power Up Modes Problem Procedure Battery doesn t power The battery may be discharged Connect the AC the computer adaptor to charge the battery User s Manual 9 5 Troubleshooting Problem Battery doesn t charge when the AC adaptor is attached Battery or Slim Select bay indicator does not glow in orange Battery doesn t power the computer as long as expected Password Problem Cannot enter password Procedure If the battery is completely discharged it will not begin charging immediately Wait a few minutes If the battery still does not charge make sure the outlet of the AC adaptor is supplying power Test it by plugging in an appliance Check whether the battery is hot or cold to the touch If the battery is too hot or too cold it will not charge properly Let it reach room temperature Unplug the AC adaptor and remove the battery to make sure the terminals are clean If necessary wipe them with a soft dry cloth dipped in alcohol Connect the AC adaptor and replace the battery Make sure it is securely seated Check the Battery indicator If it does not glow let the computer charge the battery for at least 20 minutes If the Battery indicator glows after 20 minutes let the battery continue to charge at leas
75. Infrared port Dual Pointing device USB Memory expansion Sound system Monitor i LINK IEEE1394 Modem LAN Wireless LAN Bluetooth Real time clock RTC User s Manual 9 3 Troubleshooting Self test When the computer starts up the self test will be run automatically and the following will be displayed D In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds If the self test is successful the computer tries to load the operating system depending on how the Boot Priority is set in the TOSHIBA HW Setup program If any of the following conditions are present the self test failed B The computer stops and does not proceed to display information or messages except the TOSHIBA logo W Random characters appear on the screen and the system does not function normally Wi The screen displays an error message Turn off the computer and check all cable connections If the test fails again contact your dealer Power When the computer is not plugged into an AC outlet the battery pack is the primary power source However your computer has a number of other power resources including intelligent power supply Real Time Clock battery These resources are interrelated and any one could affect apparent power problems This section provides checklists for AC power and the battery If you cannot resolve a problem after following them the cause could lie with another power resour
76. Modes for details Figure 2 18 The AC adaptor N Use only the AC adaptor that came with the computer or an equivalent optional adaptor Use of the wrong adaptor could damage your computer TOSHIBA assumes no liability for any damage in such case Use only the AC adaptor supplied as an accessory Other AC adaptors have different voltage and terminal polarities and use of them may produce heat and smoke or even result in fire or rupture User s Manual 2 17 The Grand Tour 2 18 User s Manual TECRA M2 Chapter 3 Getting Started This chapter provides basic information to get you started using your computer It covers the following topics E Setting up your work space for your health and safety Be sure also to read Instruction Manual for Safety amp Comfort This guide which is included with the computer explains product liability pmi o Connecting the AC adaptor Opening the display Turning on the power Windows XP setup Turning off the power Restarting the computer Restoring the preinstalled software from the Product Recovery DVD ROM All users should be sure to read the section Windows XP setup Setting up your work space Establishing a comfortable work site is important for you and your computer A poor work environment or stressful work habits can result in discomfort or serious injury from repetitive strain to your hands wrists or other joints Proper ambient conditions shou
77. Power button LCD Sensor switch Press the power button to turn the computer s power on and off This switch senses when the LCD panel is closed or opened and activates the Panel Power Off On feature When you close the panel the computer enters Hibernation mode and shuts down When you open the panel the computer starts in Hibernation mode Use the TOSHIBA Power Saver Utility to enable or disable this feature The default is enabled Refer to the TOSHIBA Power Saver Utility and Panel Power Off On items in Chapter 1 Introduction for details on settings F Do not put a magnetic object close to the switch The computer will automatically enter Hibernation mode and shut down even if the Panel Power Off features is disabled System indicators LEDs beneath icons light when various computer operations are in progress ss OTL T SD card DC IN 15V Power SD card d DC IN 15V Battery Disk Slim Select Wirelles Bay communication Figure 2 7 System indicators The SD card indicator glows blue when the computer is accessing the SD card slot The DC IN 15V indicator glows in green when DC power is supplied from the AC power adaptor If the adaptor s output voltage is abnormal or if the power supply malfunctions this indicator flashes orange 2 10 User s Manual The Grand Tour Power Battery Disk Slim Select Bay O q e Wireless 9 commnication The Power indicator glows in gr
78. ROM operation When the computer is accessing a CD DVD ROM an indicator on the drive glows and the Slim Select Bay indicator glows Use the WinDVD 4 application to view DVD Video discs If you have a CD RW DVD ROM drive refer also to the Writing CDs on CD RW D VD ROM drive section for precautions on writing to CDs If you have a DVD Multi drive refer also to the Writing CD DVDs on DVD Multi drive section for precautions on writing to CDs If you have a DVD R RW drive refer also to the Writing CD DVDs on DVD R RW drive DVD Dual drive section for precautions on writing to CDs Loading discs To load CD DVDs follow the steps below and refer to figures 4 6 to 4 10 1 a When the power is on press the DVD ROM eject button to open the drawer slightly Eject Button Figure 4 6 Pressing the DVD ROM eject button 4 6 User s Manual Operating Basics b Pressing the eject button will not open the drawer when the DVD ROM drive s power is off If the power is off you can open the drawer by inserting a slender object about 15 mm such as a straightened paper clip into the eject hole just to the right of the eject button Figure 4 7 Manual release with the eject hole 2 Pinch the drawer gently and pull until it is fully opened Figure 4 8 Pulling the drawer open 3 Lay the CD DVD label side up in the drawer Figure 4 9 Inserting a CD DVD User s Manual 4 7 Operating Basics i A W
79. Result Codes OK n 0 CONNECT n 1 ERROR Otherwise amp V Display Current Configuration This command displays the current configuration of the modem If nonvolatile memory is supported the stored profiles are displayed as well amp V X View profiles amp W Store current configuration Saves the current active configuration profile including S Registers The current configuration comprises a list of storable parameters illustrated in the amp V command These settings are restored to the active configuration upon receiving a Zn command or at power up Refer to the amp V command amp W Stores the current configuration amp Znzx Store telephone number This command is used to store up to four dialing strings in the modem s nonvolatile memory for later dialing The format for the command is amp Zn stored number where n is the location 0 3 to which the number should be written The dial string may contain up to 34 characters The ATDS n command dials using the string stored in location n Result Codes OK n 0 1 2 3 ERROR Otherwise Nn Error control mode selection This command determines the type of error control used by the modem when sending or receiving data WO Buffer mode No error control 1 Direct mode 2 MNP or disconnect mode The modem attempts to connect using MNP2 4 error control procedures If this fails the modem disconnects This is also known as MNP reliable mode C 8 User s Manual AT Co
80. Such as a printer or mouse Dual Pointing Device Pointing device consisting of AccuPoint and Touch Pad Both of these device can function together or separately See AccuPoint and Touch Pad DVD RAM A Digital Versatile Disc Random Access Memory is a high capacity high performance disc that lets you store large volumes of data The DVD ROM drive uses a laser to read data from the disc DVD ROM A Digital Versatile Disc Read Only Memory is a high capacity high performance disc suitable for play back of video and other high density files The DVD ROM drive uses a laser to read data from the disc echo To send back a reflection of the transmitted data to the sending device You can display the information on the screen or output it to the printer or both When a computer receives back data it transmitted to a CRT or other peripheral device and then retransmits the data to printer the printer is said to echo the CRT erase See delete Glossary 6 User s Manual Glossary escape 1 A code ASCII code 27 signaling the computer that what follows are commands used with peripheral devices such as printers and modems 2 Ameans of aborting the task currently in progress escape guard time A time before and after an escape code is sent to the modem which distinguishes between escapes that are part of the transmitted data and escapes that are intended as a command to the modem execute To interpret and execute an ins
81. TA 1 6G PM1 6 256 512MB 768M 60GB 60 802 11a b combo without WLab BT antenna 1 7G PM1 7 25641024MB 1280M 80GB 80 802 11a b combo with BT WLab antenna BTA 512 0MB 512M 802 11g without BT WLg antenna 5124512MB 1024M 802 11g with BT antenna WLg BTA 512 1024MB 1536M 802 11a g combo without WLag BT antenna 1024 0MB 1024M 802 11a g combo with BT WLag antenna BTA 1024 1024MB 2048M 802 11b BT integrated WLb BT 802 11a b combo BT WLab BT integrated 802 11g BT integrated WLg BT 802 11a g combo BT WLag BT integrated Wireless LAN Antenna WLA BTA and BT Antenna only Figures indicate the CPU operating speed in megahertz For example PM 1 4 means Mobile Intel Pentium M processor 1 4GHz User s Manual Parts Numbers User s Manual 1 2 TECRA M2 Glossary The terms in this glossary cover topics related to this manual Alternate naming is included for reference Abbreviations AC alternating current AGP accelerated graphics port ANSI American National Standards Institute APM advanced power manager ASCII American Standard Code for Information Interchange BIOS basic input output system CD ROM Compact Disc Read Only Memory CD RW Compact Disc Read Write CMOS complementary metal oxide semiconductor CPU central processing unit CRT cathode ray tube DC direct current DDC display data channel DMA direct memory access DOS disk operating system DVD digital versatile disc ECP exte
82. TECRA M2 TOSHIBA TECRA M2 Portable Personal Computer User s Manual User s Manual Copyright 2004 by TOSHIBA Corporation All rights reserved Under the copyright laws this manual cannot be reproduced in any form without the prior written permission of TOSHIBA No patent liability is assumed with respect to the use of the information contained herein TOSHIBA TECRA M2 Portable Personal Computer User s Manual First edition January 2004 Copyright authority for music movies computer programs data bases and other intellectual property covered by copyright laws belongs to the author or to the copyright owner Copyrighted material can be reproduced only for personal use or use within the home Any other use beyond that stipulated above including conversion to digital format alteration transfer of copied material and distribution on a network without the permission of the copyright owner is a violation of copyright or author s rights and is subject to civil damages or criminal action Please comply with copyright laws in making any reproduction from this manual Disclaimer This manual has been validated and reviewed for accuracy The instructions and descriptions it contains are accurate for the TOSHIBA TECRA M2 Portable Personal Computer at the time of this manual s production However succeeding computers and manuals are subject to change without notice TOSHIBA assumes no liability for damages incurred directly
83. The computer or the module could be damaged Do not remove the battery pack while the computer is in standby mode unless the computer is connected to an AC power source Data in memory will be lost If you carry the computer on board an aircraft or into a hospital be sure to shut down the computer in hibernation mode or in shutdown mode to avoid radio signal interference Benefits of standby The standby feature provides the following benefits Restores the previous working environment more rapidly than does hibernation Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System Standby feature You can use the panel power off feature User s Manual 3 9 Getting Started Executing standby You can also enable Standby by pressing Fn F3 See Chapter 5 The Keyboard for details You can enter standby mode in one of three ways 1 Click Start click Turn Off Computer and click Stand by 2 Close the display panel This feature must be enabled Refer to the Setup Action tab in TOSHIBA Power Saver Utility described in the Control Panel Open Performance and Maintenance and open TOSHIBA Power Saver 3 Slide the power button This feature must be enabled Refer to the Setup Action tab in TOSHIBA Power Saver Utility described in the Control Panel When you turn the power back on you can continue where you left when you shut down the computer
84. Use only media recommended by TOSHIBA Do not use the mouse or keyboard during writing Use only the software supplied with the computer for recording Do not run or start other software during writing Do not jar the computer during writing Do not connect disconnect external devices or install remove internal cards during writing If problems persist contact your dealer DVDZ R RW drive DVD Dual drive For more information refer to Chapter 4 Operating Basics Problem Procedure You cannot access Make sure the drive s drawer is securely closed a CD DVD in the drive Press gently until it clicks into place Open the drawer and make sure the CD DVD isproperly seated It should lie flat with the label facing up A foreign object in the drawer could block laser light from reading the CD DVD Make sure there is no obstruction Remove any foreign object Check whether the CD DVD is dirty If it is wipe it with a clean cloth dipped in water or a neutral cleaner See the Media care section in Chapter 4 for details on cleaning Some CD run correctly The software or hardware configuration may but others do not becausing a problem Make sure the hardware configuration matches your software s needs Check the CD DVD s documentation User s Manual 9 11 Troubleshooting Cannot write correctly Floppy disk drive Check the type of CD DVD you are using The drive supports DVD ROM DVD ROM DVD Video DVD R DVD RW DV
85. W When you assign a PC card HDD top priority PC is not displayed However the PC card HDD takes the position of HDD in the Boot Priority Options list above B Some modules may not be displayed 7 6 User s Manual HW Setup 1 i Keyboard External Keyboard Fn key Use this option to set a key combination on an external keyboard to emulate the Fn key on the computer s internal keyboard Setting an Fn key equivalent will let you use Hot keys by pressing the set combination instead of the Fn key PS 2 keyboard only Disabled No Fn key equivalent Default Fn Equivalent Left Ctrl Left Alt Right Ctrl Right Alt Left Alt Left Shift Right Alt Right Shift Left Alt Caps Lock If you select Left Ctrl Left Alt or Right Ctrl Right Alt for this option you cannot use the selected keys to reboot the computer in combination with the Del key For example if you select Left Ctrl Left Alt you must use Right Ctrl Right Alt and Del to reboot the computer Left Ctrl Left Alt and Del cannot be used Wake up on Keyboard When this feature is enabled and the computer is in Standby mode you can turn on the computer by pressing any key It is effective only for the internal keyboard and only when the computer is in standby mode Enabled Enables the Wake up on Keyboard Disabled Disables the Wake up on Keyboard Default LAN Wake up on LAN This feature lets the computer s power be turned on when it receives
86. ain before returning to on line data mode O3 This command issues a rate renegotiation before returning to on line data mode Result Codes OK n 0 1 3 ERROR Otherwise P Select pulse dialing This command configures the modem for pulse non touch tone dialing Dialed digits are pulsed until a T command or dial modifier is received Tone dial is the default setting Qn Result code control Result codes are informational messages sent from the modem and displayed on your monitor Basic result codes are OK CONNECT RING NO CARRIER and ERROR The ATQ command allows the user to turn result codes on or off Qo Enables modem to send result codes to the computer default Q1 Disables modem from sending result codes to the computer Result Codes OK n 0 1 ERROR Otherwise C 4 User s Manual AT Commands Vn Xn Command X0 X1 X2 X3 X4 default X5 Select tone dialing This command instructs the modem to send DTMF tones while dialing Dialed digits are tone dialed until a P command or dial modifier is received This is the default setting DCE response format This command controls whether result codes including call progress and negotiation progress messages are displayed as words or their numeric equivalents vo Displays result codes as digits v1 Displays result codes as text default Result Codes OK n 0 1 ERROR Otherwise Result code selection call progress monitoring This comman
87. aining data with power off When you turn off your computer with fully charged batteries the batteries retain data for the following approximate time periods High capacity battery pack 8800mAh about 16 days Standby mode about 50 days Boot mode Battery pack 4400mAh about 8 days Standby mode about 25 days Boot mode 2nd battery pack about 6 days about 20 days RTC battery 30 days Extending battery life To maximize the life of your battery pack E Atleast once a month disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges Before doing so follow the steps below 1 Turn off the computer s power 2 Disconnect the AC adaptor and turn on the computer s power If it does not turn on go to step 4 3 Operate the computer on battery power for five minutes If the battery pack has at least five minutes of operating time continue operating until the battery pack is fully discharged If the Battery indicator flashes or there is some other warning to indicate a low battery go to step 4 4 Connect the AC adaptor to the computer and the power cord to a power outlet The DC IN 15V indicator should glow green and the Battery indicator should glow orange to indicate that the battery pack is being charged If the DC IN 15V indicator does not glow power is not being supplied Check the connections for the AC adaptor and power cord 5 Charge the battery pack until the
88. anual C 9 AT Commands Result Codes OK n 0 3 ERROR Otherwise C 10 User s Manual TECRA M2 Appendix D S registers S registers contain the settings that determine how a number of functions of the internal modem operate For example how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connection fails You can also customize certain AT commands such as the escape sequence and command line termination The contents of the registers are changed automatically when you modify corresponding settings in your communication software If you choose however you can display and edit the contents of the registers manually when the modem is in command mode If the value is out of the acceptable range then an error is generated This chapter describes the settings for each S register S register values The format for displaying the value of an S register is ATSn where n is the register number After you type in the register press Enter The format for modifying the value of an S register is ATSn r where n is the register number and r is the new register value After you type in the register and its new value press Enter Some registers vary from one country region to another pue SO Auto answer ring number This register determines the number of rings the modem will count before automatically answering a call Enter O zero if you do not want the modem to aut
89. ask alphanumeric Keyboard characters including letters numbers and other symbols such as punctuation marks or mathematical symbols alternating current AC Electric current that reverses its direction of flow at regular intervals analog signal A signal whose characteristics such as amplitude and frequency vary in proportion to are an analog of the value to be transmitted Voice communications are analog signals Glossary 2 User s Manual Glossary ANSI American National Standards Institute An organization established to adopt and define standards for a variety of technical disciplines For example ANSI defined the ASCII standard and other information processing requirements antistatic A material used to prevent the buildup of static electricity application A group of programs that together are used for a specific task such as accounting financial planning spreadsheets word processing and games ASCII American Standard Code for Information Interchange ASCII code is a set of 256 binary codes that represent the most commonly used letters numbers and symbols async Short for asynchronous asynchronous Lacking regular time relationship As applied to computer communications asynchronous refers to the method of transmitting data that does not require a steady stream of bits to be transmitted at regular time intervals backup A duplicate copy of files kept as a spare in case the original is destroyed
90. at It may take several hours for InterVideo WinDVD Creator 2 Platinum to convert video to MPEG format and several hours more to save the MPEG file to a DVD Multi drive In order to write to a DVD RW disc that has already been written to using InterVideo WinDVD Creator 2 Platinum you will first have to delete all of the data with Drag n Drop CD DVD or similar software You will need 2 GB of empty hard disk space for every hour to write to a DVD R RW disc You cannot edit DVD RAM video data that has copyright protection using InterVideo WinDVD Creator 2 Platinum 4 16 User s Manual Operating Basics Media care This section provides tips on protecting data stored on your CD DVDs and floppy disks Handle your media with care The following simple precautions will increase the lifetime of your media and protect the data stored on them CD DVDs 1 Store your CD DVDs in the container they came in to protect them and keep them clean Do not bend the CD DVD Do not write on apply a sticker to or otherwise mar the surface of the CD DVD that contains data Hold the CD DVD by its outside edge or the edge on the center hole Fingerprints on the surface can prevent the drive from properly reading data Do not expose to direct sunlight extreme heat or cold Do not place heavy objects on your CD DVDs If your CD DVDs become dusty or dirty wipe them with a clean dry cloth Wipe from the center out do not wipe in a
91. ation IrDA 1 1 standards It enables cableless 4 Mbps 1 152 Mbps 115 2 kbps 57 6 kbps 38 4 kbps 19 2 kbps or 9 6 kbps data transfer with IrDA 1 1 compatible external devices The PC card slot accommodates two 5 mm Type Il cards or one Type III card This slot lets you easily transfer data from devices such as digital cameras and Personal Digital Assistants that use SD card flash memory You can use memory module in this slot User s Manual 1 7 Introduction Multimedia Sound system Video out jack S Video Headphone jack Microphone jack Communications Modem LAN Bluetooth Windows sound system compatible sound system provides internal speakers and microphone as well as jacks for an external microphone and headphone The video out jack lets you transfer video data to external devices Data output depends on the type of device connected to the S Video cable This jack outputs analog audio signals A 3 5 mm mini microphone jack enables connection of a three conductor mini jack for monaural microphone input An internal modem provides capability for data and fax communication It supports V 90 V 92 Refer to V 90 section in Appendix E The speed of data transfer and fax depends on analog telephone line conditions It has a modem jack for connecting to a telephone line It is preinstalled as a standard device in some markets Both of V 90 and V 92 are supported only in USA Canada and
92. ble E 1 Result codes for a V 90 connection Result code CONNECT 32000 EC CONNECT 36000 EC CONNECT 40000 EC CONNECT 44000 EC CONNECT 48000 EC CONNECT 52000 EC CONNECT 56000 EC CONNECT 28000 EC CONNECT 29333 EC CONNECT 30666 EC CONNECT 33333 EC CONNECT 34666 EC CONNECT 37333 EC CONNECT 38666 EC CONNECT 41333 EC CONNECT 42666 EC CONNECT 45333 EC CONNECT 46666 EC CONNECT 49333 EC CONNECT 50666 EC CONNECT 53333 EC CONNECT 54666 EC Description Connection at 32000 bps Connection at 36000 bps Connection at 40000 bps Connection at 44000 bps Connection at 48000 bps Connection at 52000 bps Connection at 56000 bps Connection at 28000 bps Connection at 29333 bps Connection at 30666 bps Connection at 33333 bps Connection at 34666 bps Connection at 37333 bps Connection at 38666 bps Connection at 41333 bps Connection at 42666 bps Connection at 45333 bps Connection at 46666 bps Connection at 49333 bps Connection at 50666 bps Connection at 53333 bps Connection at 54666 bps E 2 User s Manual V 90 EC stands for the Error Control method which appears only when the extended result codes configuration option is enabled EC is replaced by one of the following symbols depending on the error control method used V42bis V42 NoEC AT Command V90 V90 0 V90 1 V 42 error control and V 42bis data compression V 42 error control only No error
93. board For example Enter identifies the Enter key xxii User s Manual Preface Key operation Some operations require you to simultaneously use two or more keys We identify such operations by the key top symbols separated by a plus sign For example Ctrl C means you must hold down Ctrl and at the same time press C If three keys are used hold down the first two and at the same time press the third ABC When procedures require an action such as clicking an icon or entering text the icon s name or the text you are to type in is represented in the type face you see to the left Display es Names of windows or icons or text generated by gt ABC the computer that appears on its display screen is presented in the type face you see to the left Messages Messages are used in this manual to bring important information to your attention Each type of message is identified as shown below AR Pay attention A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment a Please read A note is a hint or advice that helps you make best use of 1 your equipment User s Manual xxiii Preface xxiv User s Manual TECRA M2 General Precautions TOSHIBA computers are designed to optimize safety minimize strain and withstand the rigors of portability However certain precautions should be observed to further reduce the risk of personal inj
94. board brace 7 Remove two screws securing the keyboard SE ee DERE N Ss Ga gt lt gt a Figure 8 6 Removing the keybord brace and removing two screws Use a point size 0 Phillips screwdriver 8 Lift up the back of the keyboard rotate it toward you and lay in face down on the palm rest W When you move the keyboard forward do not touch the keys Doing so could cause misalignment Hold the keyboard by the sides and lay it gently on the palm rest Wi The keyboard is connected to the computer by a ribbon cable Be careful not to apply tension to this cable when you lift up the keyboard Do not try to disconnect this cable Figure 8 7 Rotate the keyboard User s Manual 8 7 Optional Devices 9 One screw of Metal brace which is pressing down the keyboard cable is removed Metal brace is removed Figure 8 8 Removing the metal brace Do not touch the connectors on the memory module or on the computer Debris on the connectors may cause memory access problems 10 Insert anew module in the socket and push it down so it lies flat and is secured by two latches on either side Figure 8 9 Installing the memory module 11 The keyboard cable is pressed down with Metal brace and one screw secures the metal brace 12 Insert tabs on the front of the keyboard into corresponding notches on the computer and seat the keyboard AR When seating the keyboard be sure to fit the flexible printed circuit boa
95. can increase the portability of the computer with additional battery packs If you re away from an AC power source and your battery runs low you can replace it with a freshly charged battery Refer to Chapter 6 Power and Power Up Modes User s Manual 8 13 Optional Devices Slim Select Bay 2nd battery pack You can insert a 2nd battery pack in the computer s Slim Select Bay The battery comes with an adaptor For details on using the adaptor follow the steps below For details on inserting modules in the Slim Select Bay refer to Chapter 4 Operating Basics Installing To install the 2nd battery pack in the adaptor follow the steps below 1 Fitthe side of the 2nd battery pack opposite the connector into the adaptor 2 Lay the battery into the adaptor The latch should close automatically to secure the 2nd battery pack Figure 8 18 Inserting the secondary battery pack in the adaptor Removing To remove the 2nd battery from the adaptor follow the steps below 1 Slide the latch in the direction of the arrow shown below 2 Push the 2nd battery pack up from the bottom and lift it out Figure 8 19 Removing the 2nd battery pack from the adaptor 8 14 User s Manual Optional Devices Additional AC adaptor If you frequently transport the computer between different sites such as your home and office purchasing an AC adaptor for each location will reduce the weight and bulk of your carrying load Battery cha
96. can remove it for servicing Also called fixed disk User s Manual Glossary 7 Glossary hard disk drive HDD An electromechanical device that reads and writes a hard disk See also hard disk hardware The physical electronic and mechanical components of a computer system typically the computer itself external disk drives etc See also software and firmware hertz A unit of wave frequency that equals one cycle per second hexadecimal The base 16 numbering system composed of the digits O through 9 and the letters A B C D E and F host computer The computer that controls regulates and transmits information to a device or another computer hot key The computer s feature in which certain keys in combination with the extended function key Fn can be used to set system parameters such as speaker volume HW Setup A TOSHIBA utility that lets you set the parameters for various hardware components icon A small graphic image displayed on the screen or in the indicator panel In Windows an icon represents an object that the user can manipulate i LINK IEEE1394 This port enables high speed data transfer directly from external devices such as digital video cameras infrared port A cableless communications port capable of using infrared signals to send serial data input The data or instructions you provide to a computer communication device or other peripheral device from the keyboard or external or
97. card If you format the SD card again be sure to format it with the utility of TOSHIBA SD memory card format not in the format defined as the Windows standard format In order to run TOSHIBA SD memory card format click windows start button point to All Programs point to TOSHIBA point to Utilities and click SD memory card Format TOSHIBA SD memory card format does not format the protected area of SD memory card When you format all area of the SD memory card including the protected area use the application that responds to the copy protection system User s Manual 8 3 Optional Devices Installing an SD card To insert an SD card follow the steps below 1 Insert the SD card 2 Press gently to ensure a firm connection SD card Figure 8 3 Inserting an SD card f N Make sure the SD card is oriented properly before you insert it Removing an SD card To remove an SD card follow the steps below 1 Open the Safely Remove Hardware icon on the system tray and disablethe SD card 2 Push in the card and release it to pop the card out slightly 3 Grasp the card and remove it SD card Figure 8 4 Removing an SD card AR W Make sure the SD card indicator is out before you remove the card or turn off the computer s power If you remove the card or turn off the power while the computer is accessing the card you may lose data or damage the card E Do not remove an SD card while the computer is i
98. ce In such case contact your dealer Overheating power down If the computer s internal temperature becomes too high the computer will automatically enter Hibernation or Resume mode and shut down Problem Procedure Computer shuts down Leave the computer off until the DC IN 15V and DC IN 15V indicator stops blinking indicator blinks orange It is recommended to leave the computer off until the its interior reaches room temperature even though the DC IN 15V indicator stops blinking If the computer has reached room temperature and still does not start or if it starts but shuts down quickly contact your dealer 9 4 User s Manual Troubleshooting Computer shuts down Indicates a problem with the heat dispersal and its DC IN 15V System Please contact your dealer indicator is flashing in green AC power If you have trouble turning on the computer with the AC adaptor connected check the DC IN 15V indicator Refer to Chapter 6 Power and Power Up Modes for more information Problem Procedure AC adaptor doesn t Check the connections Make sure the cord is power the computer firmly connected to the computer and a power DC IN 15V indicator outlet does not glow green Check the condition of the cord and terminals If the cord is frayed or damaged replace it If the terminals are soiled wipe them with cotton or a clean cloth If the AC adaptor still does not power the computer contact your dealer Battery
99. ces 6 Reinstall the cover of the memory module slot Fasten the screw you loosened in Step 4 1 Be sure that the cover is closed firmly Figure 8 13 Seating the memory module cover 7 Reinstall the battery pack T After installing a memory module turn the power of the computer on to see 1 a total memory size The system will calculate the total memory size Removing memory module 2nd memory To remove the memory module make sure the computer is in boot mode then 1 Save data shutdown Windows and turn the power off 2 Remove the AC adapter cable and other cables from the computer 3 Close the display panel and turn the computer over Remove the battery pack 4 Loosen a screw on the cover of the memory module slot 5 Push slightly outwards the latch tabs on both sides that secure the memory module with a pen tip or other tools and remove the memory module 1 When the memory module rises obliquely you can remove it from the slot Latches Figure 8 14 Removing the memory module User s Manual 8 11 Optional Devices 6 Reinstall the cover of the memory module slot Fasten the screw you loosened in Step 4 7 Reinstall the battery pack After installing a memory module turn the power of the computer on to see 1 a total memory size The system will calculate the total memory size Hard disk drive pack An extra HDD expands the flexibility of your system and lets you carry your data with
100. ck all cables Are they correctly and firmly attached Loose cables can cause signal errors E Inspect all connecting cables for loose wires and all connectors for loose pins Wi Check that your floppy disk or CD DVD ROM is correctly inserted and that the floppy disk s write protect tab is correctly set Make notes of your observations and keep them in a permanent error log This will help you describe your problems to your dealer If a problem recurs the log will help you identify the problem faster Analyzing the problem Sometimes the system gives clues that can help you identify why it is malfunctioning Keep the following questions in mind W Which part of the system is not operating properly keyboard floppy disk drives hard disk drive optical media drive display Each device produces different symptoms E ls the operating system configuration set properly Check the configuration options m What appears on the display screen Does it display any messages or random characters Print a copy of the screen if you have a printer attached Look up the messages in the software and operating system documentation Check that all connecting cables are correctly and firmly attached Loose cables can cause erroneous or intermittent signals E Doany indicators light Which ones What color are they Do they stay on or blink Write down what you see E Do you hear any beeps How many Are they long or short Are they high pitched or low
101. control protocol V 90 Dial Line Rate V90 sets the maximum V 90 downstream that the modem attempts to connect V 90 disabled V 90 enabled automatic speed selection maximum modem speed default User s Manual E 3 V 90 E 4 User s Manual TECRA M2 Appendix F Internal Modem Guide This appendix describes how to install and the remove the internal modem Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described Installing the internal modem rt The internal modem is preinstalled The following is for information only To install the internal modem follow the steps below 1 Save your data and turn off the computer 2 Disconnect the AC adaptor and other peripheral devices 3 Turn the computer upside down and remove the battery pack refer to Chapter 6 Power and Power Up Modes 4 One screw in the position which removed the battery pack is removed and turn it right side up 5 Slide the display latch on the front of the computer to the right and open the display panel 6 Insert a thin object under the rim of the keyboard brace and lift out the brace 7 Remove two screws securing the keyboard 8 Lift up the back of the keyboard rotate it toward you and lay in face down on the palm rest 9 Remove two screws which you use later to secure the modem board 10 Connect the modem board cable and seat the modem board
102. ct do not scratch or break the casing and do not twist or bend the battery pack Do not remove the battery pack while the computer is in Standby mode Data is stored in RAM so if the computer loses power it will be lost In Hibernation mode data will be lost if you remove the battery or disconnect the AC adaptor before the save is completed Wait for the Disk indicator to go out Do not touch the latch while holding the computer Or you may get injured by the dropped battery by unintentional release of the latch Save your work Turn the computer s power off Make sure the Power indicator is off Remove all cables connected to the computer Turn the computer upside down User s Manual Power and Power Up Modes 5 Slide and hold the battery release latch to free the battery pack for removal after switching the battery lock into unlock position to the direction of the left then slide out the battery pack Battery Battery Lock Battery Pack Release Latch Figure 6 1 Releasing the battery pack For environmental reasons do not throw away a spent battery pack Please return spent battery packs to your TOSHIBA dealer Installing the battery pack To install a battery follow the steps below AR MH The battery pack is a lithium ion battery which can explode if not properly replaced used handled or disposed of Dispose of the battery as required by local ordinances or regulations Use only batteries recommende
103. d High Speed CD ROM MITSUBISHI CHEMICAL CORPORATION RICOH Co Ltd Ultra Speed CD ROM MITSUBISHI CHEMICAL CORPORATION User s Manual 4 9 Operating Basics TOSHIBA has confirmed the operation of CD R and CD RW media of the manufacturers above Operation of other media cannot be guaranteed CD RW can generally be rewritten about 1 000 times However the actual number of rewrites is affected by the quality of the media and the way it is used Be sure to connect the AC adaptor when you write or rewrite Be sure to close all other software programs except the writing software Do not run software such as a screen saver which can put a heavy load on the CPU Operate the computer at full power Do not use power saving features Do not write while virus check software is running Wait for it to finish then disable virus detection programs including any software that checks files automatically in the background Do not use hard disk utilities including those intended to enhance HDD access speed They may cause unstable operation and damage data Write from the computer s HDD to the CD Do not try to write from shared devices such as a LAN server or any other network device Writing with software other than Drag n Drop CD DVD has not been confirmed Therefore operation with other software cannot be guaranteed When writing or rewriting Note the following when you write or rewrite a CD R or CD RW Always copy data from the
104. d by TOSHIBA as replacements Wi Do not touch the latch while holding the computer Or you may get injured by the dropped battery by unintentional release of the latch 1 Turn the computer s power off 2 Disconnect all cables connected to the computer 3 Insert the battery pack 6 14 User s Manual Power and Power Up Modes 4 Secure the battery pack lock Check the battery lock was changed to the lock position to the direction of the right Battery Lock Battery Pack Figure 6 2 Securing the battery cover TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security User and Supervisor Passwords set in TOSHIBA Password Utility are different from the 1 Windows password User password To start the utility point to or click the following items Start gt All Programs gt TOSHIBA gt Utilities gt Password Utility The user password dialog box contains two main fields User Password and User Token User s Manual 6 15 Power and Power Up Modes T User Password field E Set button Click this button to register a password of up to 50 characters After a password is set you will be prompted to enter it when you start the computer After you set the password a dialog box will be displayed asking whether you want to save it to a floppy disk or other media If you forget the password you can open the password file on another computer Be sure to keep t
105. d in the computer this option lets you set the priority for HDD detection If the first detected HDD has a boot command the system will boot from the HDD Built in HDD 2nd HDD PC Card Default 2nd HDD Built in HDD PC Card Built in HDD PC Card 2nd HDD 2nd HDD gt PC Card gt Built in HDD PC Card gt Built in HDD 2nd HDD PC Card 2nd HDD gt Built in HDD The computer will look for the Built in HDD first next the 2nd HDD and then the PC Card Default The computer will look for the 2nd HDD first next the Built in HDD and then the PC Card The computer will look for the Built in HDD first next PC Card and then the 2nd HDD The computer will look for the 2nd HDD first next the PC Card and then the Built in HDD The computer will look for the PC Card first next the Built in HDD and then the 2nd HDD The computer will look for the PC Card first next the 2nd HDD and then the Built in HDD 1 If a boot command is not found on the first detected HDD the system will not boot from the other HDD It will search the next device in the boot priority for a boot command Network Boot Protocol This feature sets the protocol to remotely boot from the network PXE Sets PXE as the protocol Default RPL Sets RPL as the protocol 1 W PC card HDD boot is supported only by the PC card slot on the computer Support is guaranteed only for TOSHIBA PC card HDDs
106. d on a flat horizontal T surface when in use Do not set the drive on an incline greater than 209 while it is operating W Do not set anything on top of the floppy disk drive User s Manual 2 13 The Grand Tour Optical media drives One of the following optical media drives is installed in the computer DVD ROM CD RW DVD ROM DVD Multi and DVD R RW drives An ATAPI interface controller is used for CD DVD ROM operation When the computer is accessing a CD DVD an indicator on the drive glows Region codes for DVD drives and media DVD ROM CD RW DVD ROM CD DVD Multi DVDXR RW drives and media are manufactured according to the specifications of six marketing regions When you purchase DVD Video make sure it matches your drive otherwise it will not play properly Code Region 1 Canada United States 2 Japan Europe South Africa Middle East 3 Southeast Asia East Asia 4 Australia New Zealand Pacific Islands Central America South America Caribbean 5 Russia Indian Subcontinent Africa North Korea Mongolia 6 China Writable discs CDs This section describes the types of writable CD DVD discs Check the specifications for your drive to for the type of discs it can write Use Drag n Drop CD DVD to write compact discs Refer to Chapter 4 Operating Basics Wi CD R discs can be written only once The recorded data cannot be erased or changed B CD RW discs can be recorded more than once Use either 1 2 or 4
107. d selects which result codes will be used by the modem Dial tone Busy Supported Result Code detect signal detect Disable Disable OK CONNECT RING NO CARRIER ERROR Disable Disable OK RING NO CARRIER ERROR CONNECT lt RATE gt Enable Disable OK RING NO CARRIER ERROR NODIALTONE CONNECT lt RATE gt Disable Enable OK RING NO CARRIER ERROR BUSY CONNECT lt RATE gt BLACKLISTED Enable Enable OK RING NO CARRIER ERROR NODIALTONE BUSY CONNECT lt RATE gt DELAYED BLACKLISTED REORDER WARBLE CALL WAITING DETECTED Enable Enable OK RING NO CARRIER ERROR NODIALTONE BUSY CONNECT lt RATE gt RRING NO BONGTONE DELAYED BLACKLISTED REORDER WARBLE CALL WAITING DETECTED User s Manual C 5 AT Commands Dial tone detect Disabled The modem dials a call regardless of whether it detects a dial tone Enabled The modem dials only upon detection of a dial tone and disconnects the call if the dial tone is not detected within 10 seconds Busy tone detect Disabled The modem ignores any busy tones it receives Enabled The modem monitors for busy tones Result Codes OK n 0 1 2 3 4 5 ERROR Otherwise Zn Recall stored profile The modem performs a soft reset and restores recalls the configuration profile according to the parameter supplied If no parameter is specified zero is assumed Either ZO or Z1 restores the profile Result Codes OK n 0 1 ERROR Otherwise amp Cn Data Ca
108. data with the LAN the LAN Active indicator glows orange When the computer is connected to a LAN hub but is not exchanging data the Link indicator glows green Disconnecting LAN cable To disconnect the LAN cable follow the steps below Make sure the LAN Active indicator orange LED is out before you disconnect the computer from the LAN 1 Pinch the lever on the connector in the computer s LAN jack and pull out the connector 2 Disconnect the cable from the LAN hub in the same manner Check with your LAN administrator before disconnecting from the hub User s Manual 4 25 Operating Basics Cleaning the computer To help ensure long trouble free operation keep the computer free of dust and use care with liquids around the computer Be careful not to spill liquids into the computer If the computer does get wet turn the power off immediately and let the computer dry completely before you turn it on again Clean the computer using a slightly damp with water cloth You can use glass cleaner on the display Spray a small amount of cleaner on a soft clean cloth and wipe the screen gently with the cloth AR Never spray cleaner directly onto the computer or let liquid run into any part of it Never use harsh or caustic chemical products to clean the computer Remove the dust from the cooling vents on the Left side of the computer regularly with vacuum cleaner See Chapter 2 Grand Tour Left side Moving the comput
109. default channel printed in bold unless the LAN Administrator selected a different channel when configuring the Wireless LAN Access Point device Wireless IEEE 802 11 Channels Sets Revision A Frequency Range 5150 5850 MHz Note Channel ID 36 5180 40 5200 44 5220 48 5240 52 5260 56 5280 60 5300 64 5320 149 5745 3 153 5765 3 User s Manual G 3 Wireless LAN 157 5785 3 161 5805 3 Wireless Channels Sets Turbo Mode Frequency Range 5150 5850 MHz Note Channel ID 42 5210 3 US only 50 5250 3 US only 58 5290 3 US only 152 5760 3 US only 160 5800 3 US only Available Area US USA CANADA only 3 These channels are available to A B G combo type only G 4 User s Manual TECRA M2 Appendix H AC Power Cord and Connectors The power cord s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country region in which it is used All cords must meet the following specifications Length Minimum 2 meters Wire size Minimum 0 75 mm Current rating Minimum 2 5 amperes Voltage rating 125 or 250 VAC depending on country region s power standards Certification agencies U S and Canada UL listed and CSA certified No 18 AWG Type SVT or SPT 2 two conductor Australia AS Japan DENANHO Europe Austria OVE Italy Belgium CEBEC The Netherlands Denmark DEMKO Norway Finland SETI Sweden User
110. driver TOSHIBA SD Memory Boot Utility Sound Driver for Windows DVD Video Player LAN Drivers Infrared Device Driver TOSHIBA Dual Pointing Device utility TOSHIBA Power Saver TOSHIBA Mobile Extension TOSHIBA Console TOSHIBA ConfigFree TOSHIBA Zooming Utility TOSHIBA PC Diagnostic Tool TOSHIBA Controls TOSHIBA IP PHONE TOSHIBA Audio Effect TOSHIBA Rotation Settings Utility Online manual B Documentation TECRA M2 User s Manual Microsoft Windows XP manual package Instruction Manual for Safety amp Comfort End User License Agreement W Product Recovery DVD ROM Features The computer uses TOSHIBA s advanced Large Scale Integration LSI Complementary Metal Oxide Semiconductor CMOS technology extensively to provide compact size minimum weight low power usage and high reliability This computer incorporates the following features and benefits User s Manual Introduction Processor Built in The computer is equipped with an Intel processor which incorporates a math co processor a 64 KB level 1 cache memory and a 1MB level 2 cache memory It also supports Enhanced Intel SpeedStep technology Intel amp Pentium amp M processor 1 4 GHz Intel amp Pentium amp M processor 1 5 GHz Intel amp Pentium amp M processor 1 6 GHz Intel Pentium M processor 1 7 GHz 1 Some models of the computers carry Intel Centrino technology which 1 is based on three separate technologies of Intel Pentium
111. ds a number of times during the day WB Frequently look away from the computer and focus your eyes on a distant object for several seconds for example 30 seconds every 15 minutes E Take frequent short breaks instead of one or two long breaks for example two or three minutes every half hour E Have your eyes examined regularly and visit a doctor promptly if you suspect you might be suffering from a repetitive strain injury A number of books are available on ergonomics and repetitive strain injury or repetitive stress syndrome For more information on these topics or for pointers on exercises for such stress points as hands and wrists please check with your library or book vendor Also refer to the computer s Instruction Manual for Safety amp Comfort Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power It is also the fastest way to get started because the battery pack will need to be charged before you can operate from battery power The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz For details on using the AC adaptor to charge the battery pack refer to Chapter 6 Power and Power Up Modes Use only the AC adaptor supplied as an accessory Other AC adaptors have different voltage and terminal polarities and use of them may produce heat and smoke or even result in fire or rupture 3 4 U
112. dulator demodulator a device that converts modulates digital data for transmission over telephone lines and then converts modulated data demodulates to digital format where received monitor A device that uses rows and columns of pixels to display alphanumeric characters or graphic images See also CRT motherboard A name sometimes used to refer to the main printed circuit board in processing equipment It usually contains integrated circuits that perform the processor s basic functions and provides connectors for adding other boards that perform special functions Sometimes called a main board MP3 An audio compression standard that enables high quality transmission and real time playback of sound files non system disk A formatted floppy disk floppy disk you can use to store programs and data but you cannot use to start the computer See system disk nonvolatile memory Memory usually read only ROM that is capable of permanently storing information Turning the computer s power off does not alter data stored in nonvolatile memory numeric keypad overlay A feature that allows you to use certain keys on the keyboard to perform numeric entry or to control cursor and page movement O OCR Optical Character Recognition reader A technique or device that uses laser or visible light to identify characters and input them into a storage device online state A functional state of a peripheral device when it is ready to
113. e icon with the primary mouse button to display a list of regions that the modem supports A sub menu for telephony location information will also be displayed A check will appear next to the currently selected region and telephony location 3 Select a region from the region menu or a telephony location from the sub menu When you click a region it becomes the modem s region selection and the New Location for telephony will be set automatically When you select a telephony location the corresponding region is automatically selected and it becomes the modem s current region setting Properties menu Click the icon with the secondary mouse button to display properties menu on the screen Setting You can enable or disable the following settings AutoRun Mode The Region Select utility starts automatically when you start up the operating system Open the Dialing Properties dialog box after selecting region The dialing properties dialog box will be displayed automatically after you select the region Location list for region selection A submenu appears displaying location information for telephony Open dialog box if the modem and Telephony Current Location region code do not match A warning dialog box is displayed if current settings for region code and telephony location are incorrect Modem Selection If the computer cannot recognize the internal modem a dialog box is displayed Select the COM port for your modem
114. e on the back of your thighs W Adjust the back of your chair so it supports the lower curve of your spine E Sit straight so that your knees hips and elbows form approximately 90 degree angles when you work Do not slump forward or lean back too far Lighting Proper lighting can improve legibility of the display and reduce eyestrain E Position the computer so that sunlight or bright indoor lighting does not reflect off the screen Use tinted windows shades or other screen to eliminate sun glare Wi Avoid placing the computer in front of bright light that could shine directly in your eyes m f possible use soft indirect lighting in your computer work area Use a lamp to illuminate your documents or desk but be sure to position the lamp so that it does not reflect off the display or shine in your eyes User s Manual 3 3 Getting Started Work habits A key to avoiding discomfort or injury from repetitive strain is to vary your activities If possible schedule a variety of tasks into your workday If you must spend long periods at the computer finding ways to break up the routine can reduce stress and improve your efficiency E Sit in a relaxed posture Good positioning of your chair and equipment as described earlier can reduce tension in your shoulders or neck and ease back strain Wi Vary your posture frequently Occasionally stand up and stretch or exercise briefly E Exercise and stretch your wrists and han
115. e power in hibernation mode the computer takes a moment to save current memory data to the hard disk During this time the Disk indicator will light After you turn off the computer and memory is saved to the hard disk turn off the power to any peripheral devices 3 8 User s Manual Getting Started Do not turn the computer or devices back on immediately Wait a moment to let all capacitors fully discharge Standby mode pie If you have to interrupt your work you can turn off the power without exiting from your software Data is maintained in the computer s main memory When you turn on the power again you can continue working right where you left off When the AC adaptor is connected the computer will go into Standby mode according to the settings in the TOSHIBA Power Saver utility To restore operation from Standby mode press the power button or press any key The latter action works only if Wake up on Keyboard is enabled in HW Setup If the computer automatically enters Standby mode while a network application is active the application might not be restored when the computer wakes up from Standby To prevent the computer from automatically entering Standby mode disable Standby in TOSHIBA Power Saver That action however will nullify the computer s Energy Star compliance Before entering Standby mode be sure to save your data Do not install or remove a memory module while the computer is in standby mode
116. e sure the computer s wireless Bluetooth device communication switch is set to on Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on Make sure no optional Bluetooth SD card 2 is installed in the computer The built in Bluetooth function and an optional Bluetooth SD card 2 cannot operate simultaneously If problems persist contact your dealer Bluetooth For more information on wireless communication refer to Chapter 4 Operating Basics Problem Procedure Cannot access Make sure the computer s wireless Bluetooth device communication switch is set to on Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on Make sure no optional Bluetooth PC card is installed in the computer The built in Bluetooth function and an optional Bluetooth PC card cannot operate simultaneously If problems persist contact your dealer User s Manual 9 19 Troubleshooting Real Time Clock Problem Procedure The following The battery for RTC is wearing Set the date and message is Displayed time in BIOS setup with the following steps on the LCD 1 RTC battery is low or CMOS checksum is inconsistent Press F1 key to set Date Time TOSHIBA support Press F1 key BIOS setup will boot up 2 Setthe date in System Date 3 4 Set the time in System Time Press Fn R keys End key function Confirmation message will appear
117. eakers 2 8 volume control 2 1 Standby 1 12 System automatic 1 11 setting 3 9 System indicators See indica tors T TOSHIBA Audio Effect 1 15 TOSHIBA Console 1 14 TOSHIBA Console button 1 10 TOSHIBA Controls 1 13 TOSHIBA CobfigFree 1 14 TOSHIBA Dual Pointing Device utility 1 15 TOSHIBA IP Phone 1 15 TOSHIBA Mobile extension 1 14 TOSHIBA PC Diagnostic Tool 1 14 TOSHIBA Power Saver 1 13 TOSHIBA Presentation button 1 10 TOSHIBA SD Memory Boot Util ity 1 14 TOSHIBA utilities 1 10 TOSHIBA Zooming Utility 1 14 Touch Pad See Dual Pointing Device Troubleshooting See Problems TV 8 16 U USB 1 7 location 2 3 problems 9 15 V Video modes Appendix B Video RAM 1 3 Volume control 2 1 W Wireless communication 4 22 indicators 2 11 4 24 switch 2 2 4 23 User s Manual Index 5 Index Wireless LAN 1 9 problems 9 19 using 4 22 Index 6 User s Manual
118. ed as a single unit also the smallest addressable unit within the system C cache memory High speed memory which stores data that increases processor speed and data transfer rate When the CPU reads data from main memory it stores a copy of this data in cache memory The next time the CPU needs that same data it looks for it in the cache memory rather than the main memory which saves time The computer has two cache levels Level one is incorporated into the processor and level two resides in external memory capacity The amount of data that can be stored on a magnetic storage device such as a floppy disk floppy disk or hard disk It is usually described in terms of kilobytes KB where one KB 1024 bytes and megabytes MB where one MB 1024 KB card Synonym for board See board CardBus An industry standard bus for 32 bit PC cards CD ROM A Compact Disc Read Only Memory is a high capacity disc that can be read from but not written to The CD ROM drive uses a laser rather than magnetic heads to read data from the disc CD R A Compact Disc Recordable disc can be written once and read many times See also CD ROM CD RW A Compact Disc Read Write disc can be rewritten many times See also CD ROM character Any letter number punctuation mark or symbol used by the computer Also synonymous with byte chassis The frame containing the computer chip A small semiconductor containing computer logic and circuitry for
119. ee eee eee 4 25 User s Manual XV Table of Contents Cleaning the computer Hua anne nn nen 4 26 Moving the computer 0 cece eee nenn 4 26 Heat dispersal 1 2 lll aa 4 27 Chapter 5 The Keyboard Typewriter keys lesser RR nenn 5 1 F1 F12 function keys 000 02 eee eese 5 2 Soft keys Fn key combinations eee e eens 5 2 Emulating keys on enhanced keyboard lusus 5 2 Hot keys ee ee cea he RERUM SUE Mas ER oes ate 5 3 En Sticky Key 2 osse sd 5 6 Windows special keys lslllllesleelslleeese 5 6 Keypad overlay lesse I nh 5 7 Turning on the overlays lise 5 7 Temporarily using normal keyboard overlay on 5 8 Temporarily using overlay overlay off 2 222222 seen 5 8 Temporarily changing modes 0 0 ce eee eee 5 8 Generating ASCII characters 00 02 e eee eee eee 5 8 Chapter 6 Power and Power Up Modes Power conditions oi u esce e en e Rp ee eee rx ened eee 6 1 Power indicators l l nnn 6 4 Battery indicators llli 6 4 DC IN 15V indicator BR 6 4 Power indicator llle 6 5 Battery tyDes uec ERE RR ee 6 5 Main battery 2 0 pad 422 Ree eem ELE QUERER ME 6 5 2nd battery option 0 060 6 6 High capacity battery llli 6 6 Real Time Clock battery 0 0 eee ee 6 6 Care and use of the battery pack 2000 eee
120. een when the computer is on If you select Standby from Shut Down Windows this indicator flashes orange one second on two seconds off while the computer shuts down The Battery indicator shows the condition of the battery s charge Green indicates full charge orange indicates battery charging and flashing orange indicates a low battery charge Refer to Chapter 6 Power and Power Up Modes The Disk indicator glows green when the computer is accessing the built in hard disk The Slim Select Bay indicator glows in green when the computer is accessing a DVD ROM drive CD RW DVD ROM drive DVD Multi drive and DVD R RW drive or Slim Select Bay HDD adaptor in the Slim Select Bay When the secondary battery is in the Slim Select Bay the Slim Select Bay indicator glows as follows green fully charged orange charging the battery The Wireless communication indicator glows when the Bluetooth and wireless LAN functions are turned on Some models are equipped with a Wireless communication User s Manual 2 11 The Grand Tour Keyboard indicators The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator When the F10 key indicator glows the keypad overlay lets you control the cursor When the F11 key indicator glows the keypad overlay lets you enter numbers Numeric Mode Indicator Arrow Mode Indicator Figure 2 8 Keypad overlay indicators When the Caps Lock indica
121. efault Pause during dialing Pause for time specified in Register S8 before processing the next character in the dial string Ww Wait for dial tone Modem waits for a second dial tone before processing the dial string Wait for quiet answer Wait for five seconds of silence after dialing the number If silence is not detected the modem sends a NO ANSWER result code back to the caller Hook flash Causes the modem to go on hook for 0 5 seconds and then return to off hook Return to command mode Causes the modem to return to command mode after dialing a number without disconnecting the call S n Dial a telephone number previously stored using the amp Zn X command See amp Zn X command for more information The range is 0 3 En Echo command This command controls whether or not the characters entered from your computer keyboard are displayed on your monitor echoed while the modem is in command mode EO Disables echo to the computer E1 Enables echo to the computer default C 2 User s Manual AT Commands Ln Result Codes OK n 0 1 ERROR Otherwise Hook control This command instructs the modem to go on hook to disconnect a call or off hook to make the phone line busy HO Modem goes on hook default H1 Modem goes off hook Result Codes OK n 0 1 ERROR Otherwise Request ID information This command displays product information about the modem 10 Returns modem identity string and driver version
122. elect a menu item or to manipulate text or graphics designated by the pointer Press the right button to display a menu or other function depending on the software you are using You can also tap the Touch Pad to perform functions similar to those ofthe left button Click Tap the Touch Pad once Double click Tap twice Drag and drop Tap to select the material you want to move Leave your finger on the Touch Pad after the second tap and move the material Using the AccuPoint To use the AccuPoint simply push it with your finger tip in the direction you want to move the on screen pointer Two buttons above the Touch Pad work in the same way with the AccuPoint as they do with the Touch Pad Refer to the Using the Touch Pad section for details AccuPoint precautions Certain conditions can affect the on screen pointer when using AccuPoint For example the pointer may travel contrary to AccuPoint operation or an error message may appear if Wi You touch the AccuPoint during power up E You apply constant soft pressure during power up E There is a sudden temperature change E Strong stress is applied to the AccuPoint If an error message appears reboot the computer If an error message does not appear wait a moment for the pointer to stop then continue operation Replacing the cap The AccuPoint cap is an expendable item that should be replaced after prolonged use One spare AccuPoint cap is supplied with the computer
123. ems AC power 9 5 analyzing symptoms 9 2 Battery 9 5 Bluetooth 9 19 CD RW DVD ROM drive 9 9 Diskette drive 9 12 Dual Pointing device 9 14 DVD Multi drive 9 10 DVD ROM drive 9 8 DVD R RW drive DVD Dual drive 9 11 hard disk drive 9 7 hardware and system checklist 9 3 i LINK 9 17 infrared port 9 13 keyboard 9 7 LAN 9 18 LCD panel 9 7 memory expansion 9 16 modem 9 17 monitor external 9 17 mouse USB 9 14 overheating power down 9 password 9 6 PC card 9 13 power 9 4 Real time clock 9 20 SD card 9 13 self test 9 4 sound system 9 16 support from TOSHIBA 9 20 system start up 9 3 Touch Pad Accupoint 9 14 USB 9 15 Wireless LAN 9 19 Processor 1 3 Index 4 User s Manual Index R Real time clock battery See bat tery Recovery DVD ROM 3 11 Restarting the computer 3 10 S Screen See Display Scrlock Fn F12 See Soft keys SD card 1 7 indicator 2 10 inserting removing 8 4 location of slot 2 2 problems 9 13 care 8 5 Security lock 1 16 attaching 8 21 location 2 2 Self test See Problems Slim Select Bay 2 3 charging modules 4 4 HDD adaptor 8 15 indicator 2 11 location of slot 2 3 modules 1 9 options 1 17 2nd battery pack 1 17 8 14 weight saver 1 9 Soft keys emulating enhanced key board 5 2 Enter 5 3 right Ctrl key 5 3 ScrLock 5 3 Sound system 4 18 headphone jack 1 8 2 3 microphone 4 18 microphone jack 1 8 2 3 mute hot keys 5 3 problems 9 16 sp
124. eneral Device Config and Parallel Printer Some models are not equipped with Parallel Printer tab and or CPU tab Accessing HW Setup To run HW Setup click start click Control Panel click Printers and Other Hardware and select TOSHIBA HW Setup HW Setup window The HW Setup window contains the following tabs General Device Config Parallel Printer Display CPU Boot Priority Keyboard USB and LAN There are also three buttons OK Cancel and Apply OK Accepts your changes and closes the HW Setup window Cancel Closes the window without accepting your changes Apply Accepts all your changes without closing the HW Setup window User s Manual HW Setup General This window displays the BIOS version and contains two buttons Default and About Default Return all HW Setup values to the factory settings About Display the HW Setup version Setup This field displays BIOS Version and date Device Config Device Configuration This option lets you set the device configuration All Devices BIOS sets all devices Setup by 0S Operating system sets devices that it can control Default Parallel Printer Some models are equipped with Parallel Printer tab This tab lets you set the Parallel Port Mode Use the Windows Device Manager to make settings for the Parallel port Parallel Port Mode The options in this tab are ECP and Standard Bi directional ECP Sets the port type to Extended Capabilities Por
125. eplace them Or you will get burnt if you touch any of them Wi Do not touch the connectors on the memory module or on the computer Debris on the connectors may cause memory access problems Figure 8 10 Removing the memory module 6 Rotate the keyboard back into place and secure the keyboard brace as described in the previous section 7 Turn the computer upside down and replace the battery pack User s Manual 8 9 Optional Devices Installing memory module 2nd memory Follow the steps below to install amemory module 1 2 3 1 a Save data shutdown Windows and turn the power off Remove the AC adapter cable and other cables from the computer Close the display panel and turn the computer over Remove the battery pack Loosen a screw on the cover of the memory module slot Z ww Figure 8 11 Removing the memory module cover Insert the memory module obliquely against the connector of the memory module slot Gently push the memory module until it is secured in place Align the grooves of the memory module with the locking tabs of the connector and insert the module into the connector firmly If you find it difficult to install the memory module try to adjust the tabs of the connector with a pen tip or other tools Make sure to hold the memory module with your fingers on the side edges sides with grooves EN Figure 8 12 Installing a module 8 10 User s Manual Optional Devi
126. er The computer is designed for rugged durability However a few simple precautions taken when moving the computer will help ensure trouble free operation Make sure all disk activity has ended before moving the computer Check the Disk and Slim Select Bay indicators on the computer If a CD DVD is in the drives remove it Also make sure the drawer is securely closed Turn off the power to the computer Disconnect the AC adaptor and all peripherals before moving the computer Close the display Do not pick up the computer by its display panel Close all port covers Use the carrying case when transporting the computer 4 26 User s Manual Operating Basics Heat dispersal 1 To protect from overheating the CPU has an internal temperature sensor If the computer s internal temperature rises to a certain level the cooling fan is turned on or the processing speed is lowered You can select whether to control the CPU temperature by turning on the fan first then if necessary lowering the CPU speed Or by lowering the CPU speed first then if necessary turning on the fan Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver Maximum Turns on the fan first then if necessary lowers the CPU Performance processing speed Performance Uses a combination of the fan and lowering the CPU processing speed Battery Lowers the CPU processing speed first then if necessary optimized turns on the fan
127. ereo speaker Power button TOSHIBA Console Button lt control buttons TOSHIBA Presentation Button AccuPoint Control Buttons Figure 2 6 The front of the Touch Pad model with the display open Figure 2 6 shows the front of the computer with the display open To open the display push the display latch on the front of the display and lift up Position the display at a comfortable viewing angle Display hinge The display hinge holds the display screen at easy to view angles Microphone A built in microphone lets you record sound into your applications Refer to the Using the microphone section in Chapter 4 Operating Basics Display screen The LCD displays high contrast text and graphics The computer s LCD consists of up to 1024 x 768 pixels or 1400 x 1050 pixels Refer to Display Controller and Modes section in Appendix B When the computer operates on the AC adaptor the display screen s image will be somewhat brighter than when it operates on battery power The lower brightness level is intended to save battery power Stereo speakers The speakers emit sound generated by your software as well as audio alarms such as low battery condition generated by the system 2 8 User s Manual The Grand Tour Touch Pad control buttons Touch Pad AccuPoint control buttons AccuPoint TOSHIBA LN Presentation button TOSHIBA Console e t button Control buttons below the Touch Pad let you select menu i
128. ertently magnetized Do not operate the computer in close proximity to a mobile phone Leave ample ventilation room for the fan Do not block the vents Placement of the computer Position the computer and peripheral devices to provide comfort and safety Set the computer on a flat surface at a comfortable height and distance The display should be no higher than eye level to avoid eyestrain Place the computer so that it is directly in front of you when you work and make sure you have adequate space to easily operate other devices Allow adequate space behind the computer to let you freely adjust the display The display should be angled to reduce glare and maximize visibility If you use a paper holder set it at about the same height and distance as the computer 3 2 User s Manual Getting Started Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain Refer to the following tips and to figure 3 1 Below eye level Foot rest Figure 3 1 Posture and positioning of the computer Wi Place your chair so that the keyboard is at or slightly below the level of your elbow You should be able to type comfortably with your shoulders relaxed Wi Your knees should be slightly higher than your hips If necessary use a foot rest to raise the level of your knees to ease pressur
129. eyboard functions including the keypad overlay and hot keys Chapter 6 Power and Power Up Modes gives details on the computer s power resources and battery save modes and how to set a password Chapter 7 HW Setup explains how to configure the computer using the HW Setup program Chapter 8 Optional Devices describes the optional hardware available Chapter 9 Troubleshooting provides helpful information on how to perform some diagnostic tests and suggests courses of action ifthe computer doesn t seem to be working properly The Appendixes provide technical information about your computer The Glossary defines general computer terminology and includes a list of acronyms used in the text The ndex quickly directs you to the information contained in this manual Conventions This manual uses the following formats to describe identify and highlight terms and operating procedures Abbreviations On first appearance and whenever necessary for clarity abbreviations are enclosed in parentheses following their definition For example Read Only Memory ROM Acronyms are also defined in the Glossary Icons Icons identify ports dials and other parts of your computer The indicator panel also uses icons to identify the components it is providing information on Keys The keyboard keys are used in the text to describe many computer operations A distinctive typeface identifies the key top symbols as they appear on the key
130. frared Data p Association IrDA 1 1 standards It enables cableless 4 Mbps 1 15 Mbps 115 2 kbps 57 6 kbps 38 4 kbps 19 2 kbps or 9 6 kbps data transfer with IrDA 1 1 compatible external devices User s Manual The Grand Tour Wireless Slide this switch to the left to turn off Wireless communication LAN and Bluetooth functions Slide it to the right Off On to turn on the functions Some models are not switch equipped wireless LAN Left side Figure 2 2 shows the computer s left side Cooling vents Parallel port i LINK IEEE1394 port Security lock SD card slot PC card slots Figure 2 2 The left side of the computer is used to connect a parallel printer or other parallel device This port supports Extended Capabilities Port ECP standard z Parallel port This Centronics compatible 25 pin parallel port Cooling vents Cooling vents help CPU keep from overheating JN Do not to block the cooling vents Also do not to keep foreign objects out of them A pin or similar object can damage the computer s circuitry i LINK IEEE1394 Connect an external device such as a digital B s400 port video camera to this port for high speed data IEEE1394 A nm transfer Some models are equipped with a i Link port m SD card slot SD cards are used in a wide variety of external Ss devices This slot lets you transfer data from the device to your co
131. full size DVD Multi drive module lets you record data to rewritable CD DVDs as well as run either 12 cm 4 72 or 8 cm 3 15 CD DVDs without using an adaptor The read speed is slower at the center of a disc and faster at the outer pmi o edge DVD read 8 speed maximum DVD R write 2 speed DVD RW write 1 speed DVD RAM write 2 speed CD read 24 speed maximum CD R write 16 speed maximum CD RW write 8 speed maximum high speed media DVD R RW drive DVD Dual drive The full size DVD R RW drive module lets you record data to rewritable CD DVDs as well as run either 12 cm 4 72 or 8 cm 3 15 CD DVDs without using an adaptor The read speed is slower at the center of a disc and faster at the outer pie edge DVD read 8 speed maximum DVD R write 2 speed maximum DVD RW write 2 speed maximum DVD R write 2 4 speed maximum DVD RW write 2 4 speed maximum CD read 24 speed maximum CD R write 16 speed maximum CD RW write 10 speed maximum high speed media 2 16 User s Manual The Grand Tour AC adaptor The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz enabling you to use the computer in almost any country region To recharge the battery simply connect the AC adaptor to a power source and the computer See Chapter 6 Power and Power Up
132. gabyte or 720 kilobyte floppy disk It connects to a USB port You cannot format 720 kilobyte floppy disks on Windows XP but you can use previously formatted disks The Advanced Port Replicator III provides the ports available on the computer in addition to separate PS 2 mouse and PS 2 keyboard ports a digital visual interface DVI port i LINKTM IEEE1394 port line in jack and line out jack External moniter port Universal Sirial Bus port USB2 0 x 4 LAN jack Modem jack You can increase your computer s data storage capacity with additional hard disk drives They are available in the following sizes 30 billion bytes 27 94 GB 40 billion bytes 37 26 GB 60 billion bytes 55 88 GB 80 billion bytes 74 52 GB This option enables wireless LAN functions in computers that do not have wireless preinstalled It is installed by dealers only This option enables Bluetooth wireless communications in computers that do not have Bluetooth preinstalled It is installed by dealers only User s Manual Introduction Slim Select Bay options The following modules can be installed in the Slim Select Bay All other modules are options DVD ROM Refer to the Features section for details CD RW DVD ROM Refer to the Features section for details DVD Multi Refer to the Features section for details DVD R RW Refer to the Features section for details DVD Dual drive Slim Select Bay HDD An adaptor lets you instal
133. ge to computer components or otherwise cause malfunctions User s Manual General Precautions PC card overheating Some PC cards can become hot with prolonged use Overheating ofa PC card can result in errors or instability in the PC card operation Also be careful when you remove a PC card that has been used for a long time Mobile phone Use of mobile phones can interfere with the audio system Computer operation is not impaired but is recommended that a distance of 30cm be maintained between the computer and a mo bile phone in use Central Processing Unit CPU Performance Disclaimer CPU Performance in your computer product may vary from specifications under the following conditions 1 use of certain peripheral products use of battery power instead of AC power use of certain multimedia games or videos with special effects use of standard telephone lines or low speed network connections use of complex modeling software such as high end computer aided design application use of computer in areas with low air pressure high altitude gt 1 000 meters or gt 3 280 feet above sea level 7 use of computer at temperatures outside the range of 5 C to 35 C 41 F to 95 F or gt 25 C 77 F at high altitude all temperature reference are approximate CPU Performance may also vary from specifications due to design configuration Under some conditions your computer product may automatically shut down This is
134. going into standby hibernation Writing is completed if you can open the CD RW DVD ROM DVD R RW or DVD Multi drive tray Set the computer on a level surface and avoid places subject to vibration such as airplanes trains or cars Do not use an unstable surface such as a stand Keep mobile phones and other wireless communication devices away from the computer Always copy data from the HDD to the DVD RAM Do not use cut and paste The original data will be lost if there is a write error Drag n Drop CD DVD Note the following limitations when you use Drag n Drop CD DVD DVD Video cannot be created using Drag n Drop CD DVD DVD Audio cannot be created using Drag n Drop CD DVD You cannot use Drag n Drop CD DVD s music CD function to record music to the DVD R RW or DVD R RW disc Do not use the DISC Backup function of Drag n Drop CD DVD to copy DVD Video and DVD ROM with copyright protection DVD RAM disc cannot be backed up with the DISC Backup function of Drag n Drop CD DVD You cannot backup a CD ROM or CD R RW to DVD R RW or DVD R RW using the DISC Backup function of Drag n Drop CD DVD 4 14 User s Manual Operating Basics E You cannot back up DVD ROM DVD Video or DVD R RW or DVD R RW to CD R RW using the DISC Backup function of Drag n Drop CD DVD B Drag n Drop CD DVD cannot record in packet format E You might not be able to use the DISC backup function of Drag n Drop CD DVD to back up a DVD R RW o
135. h If the memory module is in slot B there will be a long beep followed by four short beeps If the both memory modules in slot A and slot B are incompatible there will be a long beep followed by two short beeps and after a pause 1 second a long beep followed by four short beeps In this case shut down the power and remove the incompatible module s Be sure to install memory module to Slot A The computer does not boot when Slot A is vacant Use a size 0 Phillips screwdriver to remove and fasten screws Use of an incorrect screwdriver can damage the screw heads Installing memory module Main memory To install a memory module make sure the computer is in boot mode then 1 Turn the computer off in boot mode Refer to the Turning off the power section in Chapter 3 Getting Started 2 Remove all cables connected to the computer 3 Turn the computer upside down and remove the battery pack refer to Chapter 6 Power and Power Up Modes 4 One screw in the position which removed the battery pack is removed and turn it right side up Figure 8 5 Removing a one screw 8 6 User s Manual Optional Devices 1 5 Slide the display latch on the front ofthe computer to the right and open the display panel 6 Insert a thin object under the rim of the keyboard brace and lift out the brace Remove a keyboard brace after surely performing step 4 If step 4 is not performed there is a possibility of damaging a key
136. h to communicate with someone on your computer you can use a messenger application However with such an application you would hear your own voice returning to you as echo during the communication if you did not use a headset system or headphone TOSHIBA Audio Effect will reduce these echoes generated on your computer Form more information on using the TOSHIBA Audio Effect refer to its help This section describes how to connect and disconnect the internal modem to and from a telephone jack The internal modem does not support voice functions All data and fax functions are supported E n case ofa lightning storm unplug the modem cable from the telephone jack E Do not connect the modem to a digital telephone line A digital line will damage the modem Region selection i Telecommunication regulations vary from one region to another so you will need to make sure the internal modem s settings are correct for the region in which it will be used To select a region follow the steps below 1 Click start point to All Programs point to TOSHIBA Internal Modem and click Region Select Utility Do not use the Country Region Select function in the Modem setup utility in the Control Panel ifthe function is available If you change the Country Region in the Control Panel the change may not take effect User s Manual 4 19 Operating Basics 2 The Region Selection icon will appear in the Windows Task Bar Click th
137. he hard disk Refer to the Software section at the front of this chapter A number of utilities and drivers are preinstalled to make your computer more convenient to use Refer to the Utilities section in this chapter When you connect an external device to the computer or when you install a component Plug and Play capability enables the system to recognize the connection and make the necessary configurations automatically The following features are either unique to TOSHIBA computers or are advanced features which make the computer more convenient to use TOSHIBA Console button TOSHIBA Presentation button Hot keys Display automatic power off Press this button to launch an application automatically The default is TOSHIBA Console Press this button to change internal display external display simultaneous display or multi monitor display Key combinations let you quickly modify the system configuration directly from the keyboard without running a system configuration program This feature automatically cuts off power to the internal display when there is no keyboard input for a time specified Power is restored when any key is pressed You can specify the time in the Monitor power off item of the Basic Setup tab in TOSHIBA Power Saver User s Manual Introduction HDD automatic power off System automatic Standby Hibernation Keypad overlay Power on password Instant security Intelligent po
138. he battery has not been used for a long time E The battery has completely discharged and been left in the computer for a long time E A cool battery is installed in a warm computer In such case follow the steps below 1 Fully discharge the battery by leaving it in the computer with the power on until the power automatically shuts off 2 Plug in the AC adaptor 3 Charge the battery until the Battery indicator glows green Repeat these steps two or three times until the battery recovers normal capacity Leaving the AC adaptor connected will shorten battery life At least once a month run the computer on battery power until the battery is fully discharged then recharge the battery 6 10 User s Manual Power and Power Up Modes Monitoring battery capacity Remaining battery power can be monitored in TOSHIBA Power Saver W Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time The computer needs this time to check the battery s remaining capacity and to calculate the remaining operating time based on the current power consumption rate and remaining battery capacity The actual remaining operating time may differ slightly from the calculated time W With repeated discharges and recharges the battery s capacity will gradually decrease Therefore an often used older battery will not operate for as long as a new battery even when both are fully charged In
139. he electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas Users should not attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician as appropriate 2 The user manual of analog equipment must contain the equipment s Ringer Equivalence Number REN and an explanation notice similar to the following The Ringer Equivalence Number REN of the modem which can vary For the REN of your modem refer to your modems label User s Manual vii User s Manual i The Ringer Equivalence Number REN assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5 3 The standard connecting arrangement telephone jack type for this equipment is jack type s USOC RJ11C The IC registration number of the modem is shown below Canada 1353A LAAINT Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit This modem has been designed to specifica
140. he media in a safe place B Delete button Click this button to delete a registered password Before you can delete a password you must first enter the current password correctly or insert a proper token B Change button Click this button to change a registered password Before you can change a password you must first enter the current password correctly or insert a proper token W Owner String text box You can use this box to associate text with the password After you enter text click Apply or OK At the time of a startup of a computer this text is displayed when you can ask for the input of a password User Token field B6 Create button You can use an SD card token instead of entering the password After you have registered a password insert an SD card and click Create You can use an SD card of any capacity but it must be formatted correctly If an unformatted card or one with an incompatible format is inserted you will be prompted to format it with a tool named TOSHIBA SD Memory Card Format To start the format tool point to or click the following items Start gt All Programs gt TOSHIBA gt Utilities gt SD Memory Card Format When you format an SD Memory card all data will be deleted Be sure to save data on the card to other media before you format the card B Disable button Click this button to invalidate the token You cannot revalidate old tokens but you can use the same SD cards to create new
141. hen the drawer is fully opened the edge of the computer will extend slightly over the CD DVD tray Therefore you will need to turn the CD DVD at an angle when you place it in the tray After seating the CD DVD however make sure it lies flat as shown in figure 4 9 E Do not touch the laser lens Doing so could cause misalignment E Do not keep foreign matter from entering the drive Check the back edge of the tray to make sure it carries no debris before closing the drive 4 Press gently at the center of the CD DVD until you feel it click into place The CD DVD should lie below the top of the spindle flush with the spindle base 5 Push the center of the drawer to close it Press gently until it locks into place If the CD DVD is not seated properly when the drawer is closed the CD DVD might be damaged Also the drawer might not open fully when you press the eject button Figure 4 10 Closing the DVD ROM drawer Removing discs A A To remove the CD DVD follow the steps below and refer to figure 4 11 Do not press the eject button while the computer is accessing the DVD ROM drive Wait for the Slim Select Bay indicator to go out before you open the drawer Also if the CD DVD is spinning when you open the drawer wait for it to stop before you remove it 1 To pop the drawer partially open press the eject button Gently pull the drawer out until it is fully opened W When the drawer pops open slightly wait a mo
142. indows operating system the hard disk will be reformatted and all data will be lost 1 Load the Product Recovery DVD ROM in the optional optical media drive and turn off the computer s power 2 Hold down the F12 key and turn on the power When In Touch with Tomorrow TOSHIBA appears release the F12 key 3 Use the left or right cursor key to select the DVD ROM icon in the display menu For details refer to the Boot Priority section in Chapter 7 HW Setup 4 Follow the on screen instructions User s Manual 3 11 Getting Started 3 12 User s Manual TECRA M2 Chapter 4 Operating Basics This chapter gives information on basic operations including using the TOSHIBA Dual Pointing Devices USB floppy disk drive the microphone the internal modem wireless communication LAN and changing Slim Select Bay modules It also provides tips on caring for your computer floppy disks and CD DVDs TOSHIBA Dual Pointing Device The computer is equipped with a dual point system a Touch Pad and an AccuPoint pointing stick Touch Pad AccuPoint Touch Pad control buttons Figure 4 1 Touch Pad and Touch Pad control buttons User s Manual Operating Basics Using the Touch Pad To use the Touch Pad simply touch and move your fingertip across it in the direction you want the on screen pointer to go Two buttons below the Touch Pad are used like the buttons on a mouse pointer Press the left button to s
143. internal storage devices The data sent or output by the sending computer is input for the receiving computer instruction Statements or commands that specify how to perform a particular task interface 1 Hardware and or software components of a system used specifically to connect one system or device to another 2 To physically connect one system or device to another to exchange information 3 The point of contact between user the computer and the program for example the keyboard or a menu interrupt request A signal that gives a component access to the processor l O Input output Refers to acceptance and transfer of data to and from a computer VO devices Equipment used to communicate with the computer and transfer data to and from it IrDA 1 1 An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps Glossary 8 User s Manual Glossary J jumper A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit K K Taken from the Greek word kilo meaning 1000 often used as equivalent to 1024 or 2 raised to the 10th power See also byte and kilobyte KB See kilobyte keyboard An input device containing switches that are activated by manually pressing marked keys Each keystroke activates a switch that transmits a specific code to the computer For each key the transmitted code is in turn
144. ity 7 4 C Cache memory 1 3 CD RW DVD ROM drive 1 5 location 2 3 problems 9 9 using 4 6 writing 4 9 Cleaning the computer 4 26 Cooling vents 2 2 CPU See Processor DC IN 15V indicator 2 10 6 4 Disk indicator 2 11 Display 1 6 2 8 See also Video modes and Monitor external automatic power off 1 10 brightness decrease 5 5 brightness increase 5 5 controller 1 6 Appendix B hinge 2 8 opening 3 5 problems 9 7 Documentation list 1 2 Docking interface 2 6 Drag n Drop CD DVD 1 14 4 14 Dual Pointing Device 1 7 1 15 AccuPoint 1 7 2 9 Touch Pad 1 7 Touch Pad control buttons 2 9 User s Manual Index 1 Index Touch Pad location 2 8 problems 9 14 using 4 2 DVD Multi drive 1 5 location 2 3 problems 9 10 using 4 6 writing 4 11 DVD ROM drive 1 4 location 2 3 problems 9 8 using 4 6 DVD R RW drive DVD Dual drive 1 6 location 2 3 problems 9 11 using 4 6 writing 4 11 Environment 3 1 Equipment checklist 1 1 Equipment setup general conditions 3 2 placement 3 2 Ergonomics lighting 3 3 seating and posture 3 3 work habits 3 4 Expansion memory See Memo ry expansion F Floppy disk care 4 17 Floppy disk drive 1 4 using 4 3 problem 9 12 Fn Ctrl enhanced keyboard simulation 5 3 Fn Enter 5 3 Fn Esc sound mute 5 3 Fn esse 1 13 Fn F1 instant security 5 4 Fn F2 power save mode 5 4 Fn F3 standby 5 4 Fn F4 hibernation 5 4 Fn F5 display selection 5 4 Fn F
145. k disc is being accessed you can lose data or damage the disk disc 3 Click start then click Turn Off Computer From the Turn Off Computer menu select Turn Off 4 Turn off the power to any peripheral devices Do not turn the computer or devices back on immediately Wait a moment to let all capacitors fully discharge Hibernation mode A The hibernation feature saves the contents of memory to the hard disk when the computer is turned off The next time the computer is turned on the previous state is restored The hibernation feature does not save the status of peripheral devices E Save your data While entering hibernation mode the computer saves the contents of memory to the HDD However for safety sake it is best to save your data manually E Data will be lost if you remove the battery or disconnect the AC adaptor before the save is completed Wait for the Disk indicator to go out E Do not install or remove a memory module while the computer is in hibernation mode Data will be lost Benefits of hibernation The hibernation feature provides the following benefits Wi Saves data to the hard disk when the computer automatically shuts down because of a low battery User s Manual 3 7 Getting Started 7 For the computer to shut down in hibernation mode the hibernation feature 1 must be enabled in two places the Hibernate tab in Power Options and Setup Action tab in TOSHIBA Power Saver Otherwise the c
146. l an optional HDD adaptor Black described in Chapter 8 Optional Devices Hard disk drive You can increase your computer s data storage capacity with an additional 30 billion bytes 27 94 GB 40 billion bytes 37 26 GB 60 billion bytes 55 89 GB and 80 billion bytes 74 52 GB hard disk drive in the Slim Select Bay HDD adaptor Slim Select Bay The secondary battery increases your 2nd battery pack computer s battery power and operating time when a main battery is also installed User s Manual Introduction 1 18 User s Manual TECRA M2 Chapter 2 The Grand Tour This chapter identifies the various components of your computer Become familiar with each component before you operate the computer Front with the display closed Figure 2 1 shows the computer s front with its display panel in the closed position System Infrared port Display latch indicators pa Pd TIT o Gr mmososo mm Wireless communication switch Volume control Figure 2 1 Front of the computer with display closed System LEDs let you monitor the status of various indicators computer functions Details are given in the Indicators section Display latch This latch secures the LCD panel in its closed position Slide the latch to open the display Volume control Use this dial to adjust the volume of the stereo speakers and the stereo headphones e Infrared port This infrared port is compatible with In
147. l size DVD ROM drive module that lets you run either 12 cm 4 72 or 8 cm 3 15 CDs or 12cm 4 72 DVDs without using an adaptor It runs DVD ROMs at maximum 8 speed and CD ROMs at maximum 24 speed The drive supports the following formats DVD ROM DVD Video CD DA CD Text Photo CD single multi session CD ROM Mode 1 Mode 2 CD ROM XA Mode 2 Form1 Form2 Enhanced CD CD EXTRA CD G Audio CD only Addressing Method 2 User s Manual Introduction CD RW DVD ROM Some models are equipped with a full size CD drive RW DVD ROM drive module that lets you run CD DVDs without using an adaptor It reads DVD ROMs at maximum 8 speed and CD ROMs at maximum 24 speed It writes CD R at up to 24 speed and CD RW at up to 24 speed For reading this drive supports the same formats as the DVD ROM drive DVD ROM DVD Video CD DA CD Text Photo CD single multi session CD ROM Mode 1 Mode 2 CD ROM XA Mode 2 Form1 Form2 Enhanced CD CD EXTRA CD G Audio CD only Addressing Method 2 DVD Multi drive Some models are equipped with a full size DVD Multi drive module that lets you record data to rewritable CD DVDs as well as run either 12cm 4 72 or 8cm 3 15 CD DVDs without using an adaptor An ATAPI interface controller is used for CD DVD ROM operation The drive reads DVDs at maximum 8 speed and CDs at maximum 24 speed It writes DVD RW at maximum single speed DVD R and DVD RAM at maxi
148. l the cable s other connector out of the computer User s Manual 4 21 Operating Basics Wireless communications The computer s wireless communication function supports both wireless LAN and Bluetooth devices Wireless LAN The Wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum Orthogonal Frequency Division Multiplexing radio technology that complies with IEEE802 11 wireless LAN standard Revision A Bor G and Turbo Mode Automatic Transmit Rate Select mechanism in the transmit range of 54 48 36 24 18 12 9 and 6Mbit s Revision A and G Revision A B B G A B G combo type Automatic Transmit Rate Select mechanism in the transmit range of 11 5 5 2 and 1Mbit s Revision B Automatic Transmit Rate Select mechanism in the transmit range of 108 96 72 48 36 24 18 and 12Mbit s Turbo Mode Revision A B G combo type Frequency Channel Selection Revision A Turbo Mode 5GHz Revision B G 2 4GHz Roaming over multiple channels Card Power Management Wired Equivalent Privacy WEP data encryption based on the 152 bit encryption algorithm Revision B G A B G combo type Wired Equivalent Privacy WEP data encryption based on the 128 bit encryption algorithm Revision A B combo B only type Advanced Encryption Standard AES data encryption based on 256bit encryption algorithm Revision B G A B G combo type 1 Wake up on LAN does not function on a Wireless LAN Sec
149. ld also be maintained for the computer s operation This section discusses the following topics W General conditions Placement of the computer Seating and posture Lighting Work habits User s Manual Getting Started General conditions In general if you are comfortable so is your computer but read the following to make sure your work site provides a proper environment Make sure there is adequate space around the computer for proper ventilation Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible The temperature should be 5 to 35 degrees Centigrade 41 to 95 degrees Fahrenheit and the relative humidity should be 20 to 80 percent Avoid areas where rapid or extreme changes in temperature or humidity may occur Keep the computer free of dust moisture and exposure to direct sunlight Keep the computer away from heat sources such as electric heaters Do not use the computer near liquids or corrosive chemicals Do not place the computer near objects that create strong magnetic fields e g stereo speakers Some computers in the computer including data storage media can be damaged by magnets Do not place the computer near magnetic objects or bring magnetic objects close to the computer Be careful of objects such as stereo speakers that produce strong magnetic fields during operation Also be careful with metal objects such as bracelets which can be inadv
150. le tapping Touch Pad or double clicking AccuPoint does not work USB mouse Problem On screen pointer does not respond to mouse operation Procedure Check the Device Select settings Open the Mouse properties icon and click the Dual Point tab Then click the Detail Setting button and click the Device Select tab Check that the Touch Pad is not selected Pressing Fn F9 to enables TOSHIBA Dual Pointing Device The system might be busy If the pointer is shaped as an hourglass wait for it to resume its normal shape and try again to move it Try changing the speed setting in the mouse control utility 1 Open the Control Panel select the Mouse icon and press Enter 2 Click the Pointer Options tab 3 Setthe speed as instructed and click OK Try changing the double click speed setting in the mouse control utility 1 Open the Control Panel select the Mouse icon and press Enter 2 Click the Buttons tab 3 Set the double click speed as instructed and click OK If problems persist contact your dealer Procedure The system might be busy If the pointer is shaped as an hourglass wait for it to resume its normal shape and try again to move it Make sure the mouse is properly connected to the USB port 9 14 User s Manual Troubleshooting Problem Double clicking does not work The mouse pointer moves too fast or too slow The mouse pointer moves erratically USB Procedure
151. lly configure to ensure compliance with Austel standards when the country region selection is set to Australia The use of other country region setting while the modem is attached to the Australian PSTN would result in you modem being operated in a non compliant manner To verify that the country region is correctly set enter the command ATI which displays the currently active setting To set the country region permanently to Australia enter the following command sequence AT TE 1 ATS133 1 AT amp F AT amp W AT TE 0 ATZ Failure to set the modem to the Australia country region setting as shown above will result in the modem being operated in a non compliant manner Consequently there would be no permit in force for this equipment and the Telecoms Act 1991 prescribes a penalty of 12 000 for the connection of non permitted equipment viii User s Manual User s Manual Notes for use of this device in New Zealand Wi The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers Failure to operate should not be reported as a fault to Telecom In addition to satisfactory line conditions a modem can only work p
152. lm rest TTL Transistor transistor logic A logic circuit design that uses switching transistors for gates and storage U Universal Serial Bus This serial interface lets you communicate with several devices connected in a chain to a single port on the computer V VGA Video Graphics Array is an industry standard video adaptor that lets you run any popular software volatile memory Random access memory RAM that stores information as long as power is supplied to the computer W warm start Restarting or resetting a computer without turning it off window A portion of the screen that can display its own application document or dialog box Often used to mean a Microsoft Windows window write protection A method for protecting a floppy disk floppy disk from accidental erasure User s Manual Glossary 13 Glossary Glossary 14 User s Manual A AC adaptor 1 3 additional 1 15 8 15 connecting 3 4 DC IN 15V port 2 5 AccuPoint See Dual Pointing Device Advanced Port Replicator Ill 1 16 8 19 ASCII characters 5 8 Auto power on See Power Battery See also Battery pack charging 6 9 extending life 6 12 indicator 2 11 6 4 location 2 6 monitoring capacity 6 11 real time clock 1 3 6 6 safety precautions 6 7 save mode 1 11 2nd 6 6 types 6 5 Battery charger 1 15 8 15 Battery pack 1 3 2 6 additional 8 13 replacing 6 13 Bluetooth 1 8 4 23 problems 9 19 TOSHIBA Stack utility 1 13 Boot prior
153. ly or slamming it shut could damage the computer Display latch Figure 3 4 Opening the display Turning on the power This section describes how to turn on the power T After you turn on the power for the first time do not turn it off until you have 1 set up the operating system Refer to the section Windows XP setup 1 If the external floppy disk drive is connected make sure it is empty If a floppy disk is in the drive press the eject button and remove the floppy disk 2 Open the display 3 Press and hold the computer s power button for two or three seconds Power button Figure 3 5 Turning on the power 3 6 User s Manual Getting Started Windows XP setup When you first turn on the power the computer s initial screen is the Microsoft Windows XP Professional Startup Screen Logo Follow the on screen directions Turning off the power The power can be turned off in one of the following modes Shut down Boot Hibernation or Standby mode Shut Down mode Boot mode A ZX When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system s main screen 1 If you have entered data save it to the hard disk or to a floppy disk 2 Make sure all disk disc activity has stopped then remove the CD DVDS or floppy disk Make sure the Disk Slim Select Bay and Slim Select Bay s module indicators are off If you turn off the power while a dis
154. me equipment use TOSHIBA portable computers comply with Class B computing device regulations User s Manual Glossary 11 Glossary Random Access Memory RAM High speed memory within the computer circuitry that can be read or written to restart Resetting a computer without turning it off also called warm boot or soft reset See also boot RGB Red green and blue A device that uses three input signals each activating an electron gun for a primary additive color red green and blue or port for using such a device See also CRT RJ11 A modular telephone jack RJ45 A modular LAN jack ROM Read Only Memory A nonvolatile memory chip manufactured to contain information that controls the computer s basic operation You cannot access or change information stored in ROM S SCSI Small Computer System Interface is an industry standard interface for connection of a variety of peripheral devices SD cards Secure Digital cards are flash memory widely used in a variety of digital devices such as digital cameras and Personal Digital Assistants serial communications A communications technique that uses as few as two interconnecting wires to send bits one after another serial interface Refers to a type of information exchange that transmits information sequentially one bit at a time Contrast Parallel interface SIO Serial Input Output The electronic methodology used in serial data transmission
155. ment to make sure the CD DVD has stopped spinning before pulling the drawer fully open E Turn off the power before you use the eject hole If the CD DVD is spinning when you open the drawer the CD DVD could fly off the spindle and cause injury 4 8 User s Manual Operating Basics 2 The CD DVD extends slightly over the sides ofthe drawer so you can hold it Hold the CD DVD gently and lift it out Figure 4 11 Removing a CD DVD 3 Push the center of the drawer to close it Press gently until it locks into place Writing CDs on CD RW DVD ROM drive Depending on the type of drive installed you may be able to write CDs The CD RW DVD ROM drive lets you write as well as read CD ROMs Observe the precautions in this section to ensure the best performance for writing CDs For information on loading and unloading CDs refer to the Using optical media drive section F CD R discs can be written to only once CD RW discs can be rewritten 1 many times Before writing or rewriting Please observe the following points when you write or rewrite the data E We recommend the following manufacturers of CD R and CD RW media Media quality can affect write or rewrite success rates CD R TAIYO YUDEN CO LTD Mitsui Chemicals Inc MITSUBISHI CHEMICAL CORPORATION RICOH Co Ltd Hitachi Maxell Ltd CD RW MITSUBISHI CHEMICAL CORPORATION RICOH Co Ltd The following special media recommend the next manufacturers Multi Speed an
156. mmands N3 V 42 MNP or buffered default The modem attempts to connect in V 42 error control mode If this fails it attempts to connect in MNP mode If this fails it connects in buffer mode and continues operation This is also known as V 42 MNP auto reliable mode same as amp Q5 4 V 42 or disconnect The modem attempts to connect in V 42 error control mode If this fails the modem disconnects W5 V 42 MNP or buffered same as 3 7 V 42 MNP or buffered same as 3 Result Codes OK n 0 1 2 3 4 5 7 ERROR Otherwise Qn Local flow control selection Q0 Disable flow control Q1 XON XOFF software flow control Q3 CTS RTS to DTE default Result Codes OK n 0 1 3 ERROR Otherwise Wn Protocol result code WO Disable protocol result code appended to DCE speed W1 Enable protocol result code appended to DCE speed default Result Codes OK n 0 1 ERROR Otherwise B View numbers in blacklist If blacklisting is in effect this command displays the numbers for which the last call attempted in the past two hours failed The ERROR result code appears in regions that do not require blacklisting Cn Data compression control This command determines the operation of V 42bis and MNP class 5 data compression On line changes do not take effect until a disconnect occurs first C0 V 42bis MNP 5 disabled No data compression C3 V 42bis MNP 5 enabled Data compression enabled default User s M
157. move any foreign object Check whether the CD DVD is dirty If it is wipe it with a clean cloth dipped in water or a neutral cleaner See the Media care section in Chapter 4 for details on cleaning The software or hardware configuration may be causing a problem Make sure the hardware configuration matches your software s needs Check the CD DVD s documentation Check the type of CD DVD you are using The drive supports DVD ROM DVD ROM DVD Video CD ROM CD DA CD Text Photo CD single multi session CD ROM Mode 1 Mode 2 CD ROM XA Mode 2 Form1 Form2 Enhanced CD CD EXTRA CD G Audio CD only Addressing Method 2 Check the region code on the DVD It must match that on the DVD ROM drive Region codes are listed in the Optical media drives section in Chapter 2 The Grand Tour If problems persist contact your dealer 9 8 User s Manual Troubleshooting CD RW DVD ROM drive For more information refer to Chapter 4 Operating Basics Problem You cannot access a CD DVD in the drive Some CD DVDs run correctly but others do not Cannot write correctly Procedure Make sure the drive s drawer is securely closed Press gently until it clicks into place Open the drawer and make sure the CD DVD is properly seated It should lie flat with the label facing up A foreign object in the drawer could block laser light from reading the CD DVD Make sure there is no obstruction Remove any fo
158. mporarily using overlay overlay off 5 8 turning on the overlays 5 7 L LAN 1 8 cable types 4 24 connecting 4 25 disconnecting 4 25 jack 2 5 LAN active indicator 2 5 Link indicator 2 5 problems 9 18 LCD See Display Video modes and Monitor external Level 2 cache See Cache mem ory Lock security See Security lock Main battery See also Battery pack Media care CD DVDs 4 17 diskettes 4 17 SD card 8 5 Memory 1 3 expansion 1 15 8 5 installing 8 6 8 10 problems 9 16 removing 8 9 8 11 Microphone jack See Sound system Modem 1 8 4 19 connecting 4 21 disconnecting 4 21 jack 2 4 problems 9 17 properties menu 4 20 region selection 4 19 Monitor external 1 7 2 4 8 16 problems 9 17 Moving the computer 4 26 User s Manual Index 3 Index N Numeric keypad See Keypad overlay O Operating system See Win dows Overlay See Keypad overlay P Panel power on off See Power Password power on 1 11 problems 9 6 starting the computer by 6 17 Supervisor 6 17 user 6 15 PC card 1 7 inserting 8 2 removing 8 2 location of slot 2 2 problems 9 13 Ports Docking interface 1 7 external monitor 1 7 i LINK 1 7 infrared 1 7 Paralell 1 7 USB 1 7 Power button location 2 8 conditions 6 1 indicators 6 4 panel on off 1 11 6 18 problems 9 4 system auto off 6 18 turning off 3 7 hibernation mode 3 7 shut down mode boot mode 3 7 standby mode 3 9 turning on 3 6 Power up modes 6 18 Probl
159. mputer An indicator on the front side of the slot glows when a card is being accessed JN Keep foreign objects out of the SD card slot A pin or similar object can damage the computer s circuitry 2 2 User s Manual The Grand Tour 7 PC card slot A PC card slot can accommodate two 5 mm na Type II cards or one Type Ill card The slot 0 supports 16 bit PC cards and CardBus PC cards WN Keep foreign objects out of the PC card slot A pin or similar object can damage the computer s circuitry acc Security lock A security cable attaches to this slot The optional security cable anchors your computer to a desk or other large object to deter theft Right side Figure 2 3 shows the computer s right side Headphone jack Slim Select Bay Microphone jack External monitor port USB ports Figure 2 3 The right side of the computer Microphone jack A 3 5 mm mini microphone jack enables connection of a three conductor mini jack for U monaural microphone input O Headphone jack This jack outputs analog audio signals Slim Select Bay A DVD ROM drive CD RW DVD ROM drive DVD Multi drive DVD R RW drive Slim Select Bay HDD adaptor or Slim Select Bay 2nd battery pack can be installed in the Slim Select Bay A weight saver can be installed when there is no module User s Manual 2 3 The Grand Tour External monitor This 15 pin port lets you connect an external C port video displa
160. mum 2 speed CD R at maximum 16 speed and CD RW at maximum 8 speed High speed media The drive supports the following formats DVD ROM DVD Video DVD R DVD RW DVD RAM CD ROM CD EXTRA Photo CD Audio CD CD ROM XA CD DA CD I CD Text CD R CD RW User s Manual 1 5 Introduction DVD R RW drive DVD Dual drive Display Some models are equipped with a full size DVD R RW drive module that lets you record data to rewritable CD DVDs as well as run either 12cm 4 72 or 8cm 3 15 CD DVDs without using an adaptor It reads DVD ROMs at maximum 8 speed and CD ROMs at maximum 24 speed It writes CD R at up to 16 speed CD RW at up to 10 speed DVD R and DVD RW at maximum 2 speed DVD R and DVD RW at maximum 2 4 speed This drive supports the same formats as the DVD ROM drive DVD ROM DVD Video DVD R DVD RW DVD R DVD RW CD DA CD Text Photo CD single multi session CD ROM Mode 1 Mode 2 CD ROM XA Mode 2 Form1 Form2 Enhanced CD CD EXTRA CD G Audio CD only Addressing Method 2 The computer s LCD panel supports high resolution video graphics The Screen can be set at a wide range of viewing angles for maximum comfort and readability Built in Graphics controller Keyboard Built in 14 1 TFT screen 16 M colors with one of the following resolutions XGA 1024 horizontal x 768 vertical pixels SXGA 1400 horizontal x 1050 vertical pixels Graphics co
161. n EG 201 121 Germany ATAAB AN005 AN006 AN007 ANO009 AN010 and DE03 04 05 08 09 12 14 17 Greece ATAAB AN005 AN006 and GR01 02 03 04 Portugal ATAAB AN001 005 006 007 011 and P03 04 08 10 Spain ATAAB AN005 007 012 and ESO1 Switzerland ATAAB AN002 All other countries regions ATAAB AN003 004 Specific switch settings or software setup are required for each network please refer to the relevant sections of the user guide for more details The hookflash timed break register recall function is subject to separate national type approvals It has not been tested for conformity to national type regulations and no guarantee of successful operation of that specific function on specific national networks can be given Japan regulations Region selection If you are using the computer in Japan technical regulations described in the Telecommunications Business Law require that you select the Japan region mode It is illegal to use the modem in Japan with any other selection Redial Up to two redial attempts can be made If more than two redial attempts are made the modem will return Black Listed If you are experiencing problems with the Black Listed code set the interval between redials at one minute or longer Japan s Telecommunications Business Law permits up to two redials on analogue telephones but the redials must be made within a total of three minutes The internal modem is approved by Japan Approvals Institute for Telecomm
162. n Standby or Hibernation mode The computer could become unstable or data in the SD card could be lost 8 4 User s Manual Optional Devices SD card care Set the write protect switch to the lock position if you do not want to record data 1 2 3 7 8 Do not write to an SD card if the battery power is low Low power could affect writing accuracy Do not remove an SD card while read write is in progress The SD card is designed so that it can be inserted only one way Do not try to force the card into the slot Do not leave an SD card partially inserted in the slot Press the SD card until you hear it click into place Do not twist or bend SD cards Do not expose SD cards to liquids or store in humid areas or lay media close to containers of liquid After using an SD card return it to its case Do not touch the metal part or expose it to liquids or let it get dirty Creation of a boot disk In TOSHIBA SD Memory Boot Utility a boot disk can be created with SD memory card Refer to the Utilities of Chapter 1 Introduction for details Memory expansion This computer is equipped with two memory module sockets Slot A is beneath the keyboard and Slot B is in the underside of the computer You can increase the capacity of RAM to maximum of 2048MB by installing an additional memory or replacing default memories with additional memories J B Observe the following instructions according to the model you
163. n the drive Some CD DVDs run correctly but others do not Procedure Make sure the drive s drawer is securely closed Press gently until it clicks into place Open the drawer and make sure the CD DVD is properly seated It should lie flat with the label facing up A foreign object in the drawer could block laser light from reading the CD DVD Make sure there is no obstruction Remove any foreign object Check whether the CD DVD is dirty If it is wipe it with a clean cloth dipped in water or a neutral cleaner See the Media care section in Chapter 4 for details on cleaning The software or hardware configuration may be causing a problem Make sure the hardware configuration matches your software s needs Check the CD DVD s documentation Check the type of CD DVD you are using The drive supports DVD ROM DVD ROM DVD Video Recordable DVD DVD R DVD RW DVD RAM CD ROM CD DA CD Text Photo CD single multi session CD ROM Mode 1 Mode 2 CD ROM XA Mode 2 Form1 Form2 Enhanced CD CD EXTRA CD G Audio CD only Addressing Method 2 Recordable CD CD R CD RW Check the region code on the DVD It must match that on the CD RW DVD ROM drive Region codes are listed in the Optical media drives section in Chapter 2 The Grand Tour 9 10 User s Manual Troubleshooting Problem Procedure Cannot write correctly If you have trouble writing make sure you are observing the following precautions
164. nction computer and to the device Make sure the device s power is turned on Reinstall the drivers Open the Windows Control Panel and double click the Add Hardware icon Follow the on screen directions Restart Windows If problems persist contact your dealer Modem Refer to the online help files for Appendix C AT Commands and AppendixD S registers Problem Procedure Communication Make sure the computer s internal modem software can tinitialize settings are correct Refer to Phone and Modem modem Properties in the Control Panel You can hear a dial If the call is going through a PBX machine make tone but can t makea sure the communication application s tone dial call detection feature is disabled You can also use the ATX command Refer to the online help files for Appendix C AT Commands User s Manual 9 17 Troubleshooting LAN Problem You place a call but a connection can t be made After making a call you can t hear a ring Communication is cut off unexpectedly A CONNECT display is quickly replaced by NO CARRIER Character display becomes garbled during a communication You cannot receive an incoming call Problem Cannot access LAN Wake up on LAN does not work Procedure Make sure the settings are correct in your communications application Make sure the tone or pulse selection in your communications application is set correctly You can also use the ATD command Refer
165. nded capabilities port FDD floppy disk drive FIR fast infrared HDD hard disk drive IDE integrated drive electronics WO input output IrDA Infrared Data Association IRQ interrupt request KB kilobyte LCD liquid crystal display User s Manual Glossary 1 Glossary LED light emitting diode LSI large scale integration MS DOS Microsoft Disk Operating System OCR optical character recognition reader PCB printed circuit board PCI peripheral component interconnect RAM random access memory RGB red green and blue ROM read only memory RTC real time clock SCSI small computer system interface SIO serial input output SXGA super extended graphics array plus Abbreviations continued TFT thin film transistor UART universal asynchronous receiver transmitter USB Universal Serial Bus UXGA ultra extended graphics array VESA Video Electronic Standards Association VGA video graphics array VRT voltage reduction technology XGA extended graphics array A AccuPoint A pointing device integrated into the TOSHIBA computer keyboard adaptor A device that provides an interface between two dissimilar electronic devices For example the AC adaptor modifies the power from a wall outlet for use by the computer This term also refers to the add in circuit cards that control external devices such as video monitors and magnetic tape devices allocate To assign a space or function for a specific t
166. ned and plug the i LINK IEEE1394 cable into the computer Plug the other end of the cable into the device 8 18 User s Manual Optional Devices Note the following when you use i LINK E You may need to install drivers for your i LINK devices Wi Notall i LINK devices have been tested Therefore compatibility with all i LINK devices cannot be guaranteed W Use S100 S200 or S400 cables no longer than three meters Some devices might not support standby or automatic off functions W Do not connect or disconnect an i LINK device while it is using an application or when the computer is automatically shutting it down to save power Data might be destroyed W When multiple IEEE1394 devices are connected to a PC the devices may not correctly be identified This problem may occur when Windows XP is restarted while the devices are connected or when the power to the IEEE 1394 devices is turned on before the PC is turned on If it occurs disconnect the IEEE 1394 cables and then reconnect them Disconnecting i 1 Open the Safety Remove Hardware icon on the Task Bar 2 Point to i LINK IEEE1394 device and click 3 Disconnect the cable from the computer then from the i LINK device Refer also to the documentation that came with your i LINK device Advanced Port Replicator Ill A 1 In addition to the ports available on the computer the Advanced Port Replicator Ill provides Serial port and separate ports for PS
167. ng the ATO command A pause the length of which is set by Escape Guard Time S12 must be completed after an escape sequence is entered This pause prevents the modem from interpreting the escape sequence as data The value ofthe escape sequence character may be changed using register S2 A Repeat last command This command repeats the last command string entered Do not precede this command with an AT prefix or conclude it by pressing Enter A Answer command This command instructs the modem to go off hook and answer an incoming call User s Manual AT Commands Bn Communication standard setting This command determines the communication standard CCITT or Bell BO Selects CCITT V 22 mode when the modem is at 1200 bps B1 Selects Bell 212A when the modem is at 1200 bps default B15 Selects V 21 when the modem is at 300 bps B16 Selects Bell 103J when the modem is at 300 bps default Result Codes OK n 0 1 15 16 ERROR Otherwise Dn Dial This command instructs the modem to dial a telephone number Enter n the telephone number and any modifiers after the ATD command Any digit or symbol 0 9 A B C D may be dialed as touch tone digits Characters such as spaces hyphens and parentheses do not count They are ignored by the modem but you may want to include them to make the number and modifiers easier to read The following may be used as phone number modifiers P Pulse dialing T Touch tone dialing d
168. nt to Utilities and click Accessibility Windows special keys The keyboard provides two keys that have special functions in Windows Windows logo key activates the start menu and the other the application key has the same function as the secondary mouse button Au Hy This key activates the Windows start menu i This key has the same function as the secondary mouse button 5 6 User s Manual The Keyboard Keypad overlay Your computer s keyboard does not have an independent numeric keypad but its numeric keypad overlay functions like one The keys in the center of the keyboard with gray letters make up the numeric keypad overlay The overlay provides the same functions as the numeric keypad on the 101 102 key enhanced keyboard in figure 5 2 Turning on the overlays The numeric keypad overlay can be used for numeric data input or cursor and page control Arrow mode To turn on the Arrow mode press Fn F10 The Arrow mode F10 indicator lights Now try cursor and page control using the keys shown in figure 5 2 Press Fn F10 again to turn off the overlay Numeric mode To turn on the Numeric mode press Fn F11 The Numeric mode F11 indicator lights Now try numeric data entry using the keys in figure 5 2 Press Fn F11 again to turn off the overlay FF 29 Jr Jr Je Je n r de de de de Frrrr aaa
169. ntroller maximizes display performance Refer to Display Controller and Modes section in Appendix B for more information 85 keys or 86 keys compatible with IBM enhanced keyboard embedded numeric overlay dedicated cursor control ay and keys See Chapter 5 The Keyboard for details 1 6 User s Manual Introduction TOSHIBA Dual Pointing Device Built in Touch Pad Built in AccuPoint Ports Parallel External monitor Universal Serial Bus USB 2 0 Docking interface i LINK IEEE1394 Infrared Slots PC card SD card A Touch Pad and control buttons in the palm rest enable control of the on screen pointer and scrolling of windows This pointer control stick located in the center of the keyboard provides convenient control of the cursor Parallel printer or other parallel device ECP compatible 15 pin analog VGA port supports VESA DDC2B compatible functions The computer has two Universal Serial Bus ports that comply with the USB 2 0 standard which enables data transfer speeds 40 times faster than the USB 1 1 standard The ports also support USB 1 1 This port enables connection of an optional Advanced Port Replicator III described in the Options section This port enables high speed data transfer directly from external devices such as digital video cameras Some models are equipped with a i LINK port The serial infrared port is compatible with Infrared Data Associ
170. o automatically set proper microphone input volumes and ensure that your voice input s are working correctly As you speak into the microphone the Sound Meter indicates the audio signal that your PC is receiving The Noise Reduction enhancement helps to eliminate ambient noise from the voice input signal to provide a clean and clear signal to applications This feature can be used with any microphone The audio controller can be powered down when the audio function is idle To enable the Audio Power Management follow the steps below 1 Clicked the Power Management tab 2 Select the Normal Power Savings in the Power Mode pull down list If the No Power Savings is selected the audio controller always runs 4 18 User s Manual Operating Basics i If you want to a more effect for the power management you can select another mode the High Power Savings which can save the power than the Normal Power Savings To select it follow the steps below 1 Clicked the Power Management tab 2 Select the High Power Savings in the Power Mode pull down list 3 Input a time in Power Save Delay Seconds If the High Power Saving is selected you need to play an audio file once before you use a microphone or play an audio CD by the analog CD audio Audio Effect Modem i A TOSHIBA Audio Effect provides you with a hands free environment for holding mutual communication via the Internet Protocol or Local Area Network If you wis
171. oked for 2 n this computer CD ROM refers to the Slim Select Bay optical media drive 7 4 User s Manual HW Setup m B PC card HDD boot is supported only by slot 0 on the computer Support I is guaranteed only for TOSHIBA PC card HDDs W When you assign a PC card HDD top priority PC is not displayed However the PC card HDD takes the position of HDD in the Boot Priority Options list above To change the boot drive follow the steps below 1 Hold down F12 and boot the computer 2 The following menu will be displayed with the following icons Built in HDD Slim Select Bay HDD CD ROM FDD or SD memory card Network LAN PC ATA card boot Fi A bar will appear only under the selected device 3 Use the left right cursor keys to highlight the boot device you want and press Enter e F W fa supervisor password is set the menu above does not appear when 1 you use the user password to start the computer E The selection method above does not change the boot priority settings in HW Setup Wi f you press a key other than one of those above or if the selected device is not installed the system will boot according to the current setting in HW Setup W Support of PC ATA card boot is guaranteed only for TOSHIBA PC card HDDs m APC ATA card takes the position of HDD in the Boot Priority Options list User s Manual 7 5 HW Setup HDD Priority Options If more than one HDD is installe
172. omatically answer at all When disabled the modem can only answer with an ATA command Range 0 255 Default 0 Units rings User s Manual S registers S1 Ring counter This register is read only The value of S1 is incremented with each ring If no ring occurs over a six second interval this register is cleared Range 0 225 Default 0 Units rings S2 AT escape character user defined S3 This register determines the ASCII values used for an escape sequenzce The default is the character The escape sequence allows the modem to exit data mode and enter command mode when on line Values greater than 127 disable the escape sequence Range 0 255 ASCII decimal Default 43 Units ASCII Command line termination character user defined This register determines the ASCII values as the carriage return character This character is used to end command lines and result codes Range 0 127 ASCII decimal Default 13 carriage return Units ASCII S4 Response formatting character user defined This register determines the ASCII value used as the line feed character The modem uses a line feed character in command mode when it responds to the computer Range 0 127 ASCII decimal Default 10 line feed Units ASCII D 2 User s Manual S registers S5 Command line editing character user defined This register sets the character recognized as a backspace and pertains to asynchronous only
173. omputer will shut down in Standby mode If battery power becomes depleted data saved in Standby mode will be lost Wi You can return to your previous working environment immediately when you turn on the computer Wi Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System hibernate feature E You can use the panel power off feature Starting Hibernation J You can also enable Hibernation by pressing Fn F4 See Chapter 5 The Keyboard for details To enter Hibernation mode follow the steps below Click start Select Turn Off Computer Open the Turn Off Computer dialog box Hibernate is not displayed Press the Shift key The Standby item will change to Hibernate Select the Hibernate o BROWN Automatic Hibernation The computer will enter Hibernate mode automatically when you press the power button or close the lid First however make the appropriate settings according to the steps below 1 Open the Control Panel 2 Open Performance and Maintenance and open Power Options 3 Select the Hibernate window in the Power Options Properties select the Enable hibernation check box and click the Apply button 4 Open TOSHIBA Power Saver 5 Selectthe Setup Action window 6 Enable the desired Hibernation settings for When I slide the power button and When I close the lid 7 Click the OK button Data save in hibernation mode When you turn off th
174. on on PC and the test of built in devices can also be performed You can boot TOSHIBA PC Diagnostic Tool from the menu bar as follows m Start All Programs TOSHIBA Utilities PC Diagnostic Tool This utility enables hot insertion of Slim Select Bay modules that is you can remove insert Slim Select Bay modules while the computer is on To activate this utility select TOSHIBA Mobile Extension from TOSHIBA Console ConfigFree is a suite of utilities to allow easy control of communication device and network connections ConfigFree also allows you to find communication problems and create profiles for easy switching between location and communication networks You can boot ConfigFree from the menu bar as follows m Start All Programs TOSHIBA Networking ConfigFree User s Manual Introduction Options TOSHIBA Dual Pointing Device utility TOSHIBA IP Phone TOSHIBA Audio Effect TOSHIBA Rotation Settings Utility This utility has the following functions To disable enable TOSHIBA Dual Pointing Device with Fn F9 keys To customize the functions of TOSHIBA Dual Pointing Device easily TOSHIBA IP Phone lets you call an IP Phone use answering machine function send and receive text message while you re talking You can boot TOSHIBA IP Phone from the menu bar as follows E Start All Programs TOSHIBA RealtimeCommunication IPPhone This utility provides you with a hands
175. onal 2nd battery pack supply power to maintain data and program in memory If the battery pack s is completely discharged Standby mode does not function and the computer loses all data in memory W Do not have only High capacity battery when having connected High capacity battery with the computer Real Time Clock battery pmi o The Real Time Clock RTC battery provides power for the internal real time clock and calendar It also maintains the system configuration If the RTC battery becomes completely discharged the system loses this data and the real time clock and calendar stop working The following message appears when you turn on the power eS RTC battery is low or CMOS checksum is inconsistent Press F1 key to set Date Time The computer s RTC battery is a lithium ion battery and should be replaced only by your dealer or by a TOSHIBA service representative The battery can explode if not properly replaced used handled or disposed of Dispose of the battery as required by local ordinances or regulations You can change the setting of RTC by pressing F1 key Refer to Chapter 9 Troubleshooting for the detail 6 6 User s Manual Power and Power Up Modes Care and use of the battery pack The battery pack is a vital component of portable computing Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack Follow the instruction
176. onents and accessory devices Then read Getting Started for step by step instructions on setting up your computer If you are an experienced computer user please continue reading the preface to learn how this manual is organized then become acquainted with this manual by browsing through its pages Be sure to look over the Special features section of the Introduction to learn about features that are uncommon or unique to the computers and carefully read HW Setup If you are going to install PC cards or connect external devices such as a monitor be sure to read Chapter 8 Optional Devices Manual contents This manual is composed of the following nine chapters nine appendixes a glossary and an index Chapter 1 ntroduction is an overview of the computer s features capabilities and options Chapter 2 The Grand Tour identifies the components of the computer and briefly explains how they function Chapter 3 Getting Started provides a quick overview of how to begin operating your computer and gives tips on safety and designing your work area User s Manual Preface Chapter 4 Operating Basics includes instructions on using the following devices TOSHIBA Dual Pointing Device USB floppy disk drive Slim Select Bay modules optical media drives microphone modem Wireless communication features LAN It also provides tips on care of the computer floppy disks and CD DVDs Chapter 5 The Keyboard describes special k
177. ooth functions with the on off switch No transmissions are sent or received when the switch is off Slide the switch to the right to turn it on and to the left to turn it off N Set the switch to off in airplanes and hospitals Check the indicator It will stop glowing when the wireless communication function is off User s Manual 4 23 Operating Basics Wireless communication Indicator LAN AN i The wireless communication indicator indicates the status of the wireless communication functions Indicator status Indication Indicator off Wireless communication switch is set to off Automatic power down because of overheating Power malfunction Indicator glows Wireless communication switch is on Wireless LAN or Bluetooth is turned on by an applica tion If you used the Task Bar to disable W LAN restart the computer or follow the procedures below to enable the system to recognize W LAN Open or click the following start Control Panel System Hardware Device Manager Network adapters Atheros AR5001X Wireless Network Adaptor or Intel amp PRO Wireless LAN 2100 3B Mini PCI Adapter or Intel amp PRO Wireless 2100A LAN Mini PCI Adapter and enable The computer has built in support for Ethernet LAN 10 megabits per second 10BASE T Fast Ethernet LAN 100 megabits per second 100BASE Tx and Gigabit Ethernet LAN 1000 megabits per second 1000BASE T Some models are equipped with a Gigabit Ethrnet LAN This section de
178. optional TOSHIBA Battery charger to charge the battery pack Never attempt to charge the battery pack with any other charger User s Manual 6 9 Power and Power Up Modes 1 1 Time The following table shows the approximate time required to fully charge a discharged battery Charging time hours Battery type Power on Power off High capacity battery pack 8800mAh about 10 5 to 21 5 about 4 5 Main battery pack 4400mAh about 5 0 to 11 0 about 2 5 2nd battery pack about 4 5 to 9 5 about 3 RTC battery 8 Doesn t charge The charging time when the computer is on is affected by ambient temperature the temperature of the computer and how you use the computer If you make heavy use of external devices for example the battery might scarcely charge at all during operation Refer also to the section Maximizing battery operating time Battery charging notice The battery may not charge right away under the following conditions Wi The battery is extremely hot or cold If the battery is extremely hot it might not charge at all To ensure the battery charges to its full capacity charge the battery at room temperature of 10 to 30 C 50 to 88 F E The battery is nearly completely discharged Leave the AC adaptor connected for a few minutes and the battery should begin charging The Battery indicator may show a rapid decrease in battery operating time when you try to charge a battery under the following conditions E T
179. or indirectly from errors omissions or discrepancies between the computer and the manual Trademarks Intel Intel SpeedStep Pentium and Centrino are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries regions Windows and Microsoft are registered trademarks of Microsoft Corporation Photo CD is a trademark of Eastman Kodak Bluetooth is a trademark owned by its proprietor and used by TOSHIBA under license i LINK is trademark and registered trademark of Sony Corporration Other trademarks and registered trademarks not listed above may be used in this manual ii User s Manual User s Manual FCC information Product Name TECRA M2 Model number PTM20 FCC notice Declaration of Conformity Information This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 ofthe FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the
180. or or monochrome To change the display settings press Fn F5 If you disconnect the monitor before you turn the computer off be sure to press Fn F5 to switch to the internal display Refer to Chapter 5 The Keyboard for details on using hot keys to change the display setting You can connect a television set to the Video out jack on the computer Follow the steps below Using the TOSHIBA Console button 1 Connect the TV adaptor cable s S Video plug to the Video out jack on the computer 2 Connect the TV adaptor cable s S Video plug to the S Video jack on the TV 3 Press the TOSHIBA Console button You can use the hot keys Fn F5 to change the display device Refer to Chapter 5 The Keyboard 8 16 User s Manual Optional Devices When changing to TV OUT by TOSHIBA Console button it is TOSHIBA controls and it is necessary to set TV OUT as TOSHIBA Console button beforehand If a television is connected to the computer set the TV type in Display Properties Follow the steps below Wi Click start and click Control Panel W Double click the Display icon to open the Display Properties window W Click the Settings tab and click the Advanced button W Click the GeForce FX Go5200 32M 64M tab click Device Settings and click Select Output Device E Select Advanced and select TV in the Device Selection window Wi Select the Format box and select the format that your TV supports Changing the
181. ot boot from hard disk drive Slow performance Procedure Press hotkeys Fn F5 to change the display priority to make sure it is not set for an external monitor Refer to your software s documentation to determine if the software is causing the difficulty Run the diagnostic test Contact your dealer if the problems continue Procedure Check if a floppy disk is in the floppy disk drive If a floppy disk is inserted remove it and reboot There may be a problem with your operating system files Refer to your OS documentation Your files may be fragmented Run SCANDISK and defragmenter to check the condition of your files and disk Refer to your OS documentation or online HELP for information on running SCANDISK and the defragmenter As a last resort reformat the hard disk Then reload the operating system and other files If problems persist contact your dealer User s Manual 9 7 Troubleshooting DVD ROM drive For more information refer to Chapter 4 Operating Basics Problem You cannot access a CD DVD in the drive Some CD DVDs run correctly but others do not Procedure Make sure the drive s drawer is securely closed Press gently until it clicks into place Open the drawer and make sure the CD DVD is properly seated It should lie flat with the label facing up A foreign object in the drawer could block laser light from reading the CD DVD Make sure there is no obstruction Re
182. ot be able to read DVD R RW discs You cannot partially delete any data written to a CD RW DVD RW or DVD RW disc Data written to a CD R DVD R DVDH R disc cannot be deleted either in whole or in part Data deleted erased from a CD RW DVD RW and DVD RW disc cannot be recovered Check the content of the disc carefully before you delete it If multiple drives that can write data to discs are connected be careful not to delete data from the wrong drive In writing to a DVD R RW or DVD R RW disc some disc space is required for file management so you may not be able to write the full capacity of the disc Since the disc is based on the DVD standard it might be filled with dummy data if the written data is less than about 1 GB Even if you write only a small amount of data it might take time to fill in the dummy data DVD RAM formatted by FAT32 cannot be read in Windows 2000 without DVD RAM Driver Software When multiple drives that can write data to discs are connected be careful not to write to the wrong drive Be sure to connect the AC adaptor before you write or rewrite Before you enter standby hibernation mode be sure to finish DVD RAM writing Writing is finished if you can eject DVD RAM media Be sure to close all other software programs except the writing software Do not run software such as a screen saver which can put a heavy load on the CPU Operate the computer in the full power mode Do not use power saving featu
183. ots for slot B 2 Remove the battery er Bid posl ieu Remove the memory module ne an 4 Replace the battery and or connect the AC adaptor 5 Turn on the power defective If problems persist contact your dealer Sound system Refer also to documentation for your audio devices Problem Procedure No sound is heard Adjust the volume control dial Check the software volume settings Make sure the headphone connection is secure If problems persist contact your dealer Annoying sound You may be experiencing feedback Refer to is heard Using the microphone in Chapter 4 Operating Basics If problems persist contact your dealer 9 16 User s Manual Troubleshooting Monitor Refer also to Chapter 8 Optional Devices and to your monitor s documentation Problem Procedure Monitor does not turn Make sure that the external monitor s power on Switch is on Confirm that the external monitor s power cable is plugged into a working power outlet No display Try adjusting the contrast and brightness controls on the external monitor Press hot keys Fn F5 to change the display priority and make sure it is not set for the internal display Display error occurs Check that the cable connecting the external monitor to the computer is attached firmly If problems persist contact your dealer i LINK IEEE1394 Problem Procedure i LINK device does not Make sure the cable is securely connected to the fu
184. out carrying the computer 1 Use a point size 0 Phillips screwdriver Removing the HDD pack To remove the HDD pack follow the steps below and refer to figures 8 15 and 8 16 1 Setthe computer to boot mode and turn off the power 2 Disconnect the AC adaptor and all external cables connected to the computer 3 Remove the main battery and optional secondary battery when it is used 4 Turn the computer upside down and remove one screw securing the HDD cover 5 A small row of ridges mark latches securing the cover Press on these ridges until you hear a click 6 Press on the arrows and lift the cover up and out to remove it D Figure 8 15 Removing the HDD pack cover 7 Raise the HDD s plastic tab pinch it and slide the HDD pack to disconnect from the connector Be sure to slide the HDD pack first and confirm that the HDD pack has disconnected 8 12 User s Manual Optional Devices 8 Lift the HDD pack and remove it Figure 8 16 Removing the HDD pack Installing the HDD pack To install the hard disk drive follow the steps below 1 Place the HDD into the space for HDD Slide the HDD to connect to the connector 2 Fold over the plastic tab so that it goes into the HDD space Press the HDD to ensure a firm connection Figure 8 17 Installing the HDD pack 3 Seat the cover and press down until the latches click into place 4 Secure the cover with a screw Additional battery pack You
185. p in the microphone and amplified back to the speaker which amplifies it again to the microphone This howling occurs repeatedly and causes a very loud high pitched noise It is a common phenomenon that occurs in any sound system when the microphone input is output to the speaker throughput and the speaker volume is too loud or too close to the microphone You can control throughput by adjusting the volume of your speaker or through the Mute function To adjust the volume or activate Mute click start point to All Programs point to Accessories point to Entertainment and click Volume control In the Master volume panel you can use the side bars to adjust the volume level or click Mute at the bottom of the panel SoundMAX control panel 1 The SoundMAX control panel lets you control additional functions for the Microphone Enhancement and Audio Power Management To launch the SoundMAX Control Panel follow the steps below 1 Click Start and click Control Panel 2 If you are viewing the Control Panel in Category View click on Switch to Classic View 3 Double click the SoundMAX icon The Microphone Setup allows you to optimize the microphone input settings for your particular configuration Choose Standard Microphone if you have an ordinary desktop microphone Choose Headset if you have a wearable microphone that is positioned directly in front of your mouth You can launch the Setup Wizard from the Control Panel to help you t
186. play DVD Video It has an on screen interface and functions Click Start point to All Programs point to InterVideo WinDVD 4 then click InterVideo WinDVD 4 This software enables communication between remote Bluetooth devices 1 Bluetooth cannot be used in models that do not have a Bluetooth module User s Manual Introduction TOSHIBA SD Memory Boot Utility TOSHIBA Zooming Utility Drag n Drop CD DVD TOSHIBA Console TOSHIBA PC DiagnosticTool TOSHIBA Mobile Extension TOSHIBA ConfigFree The TOSHIBA SD memory boot utility is a utility which can create SD memory card to a boot disk You can boot TOSHIBA SD Memory Boot Utility from the menu bar as follows E Start All Programs TOSHIBA Utility SD Memory Boot Utility This utility allows you to enlarge or reduce the icon size on the desktop or the application widow This easy to use software lets you record CD DVDs with just a few mouse clicks You can create CD DVDs in several formats including audio CDs that can be played on a standard stereo CD player and data CDs to store the files and folders on your hard drive This software can be used on a model with CD RW DVD ROM drive DVD Multi drive and DVD R RW drive TOSHIBA Console is a graphical user interface that provides easy access to help and services It is the default function launched by the TOSHIBA Console button TOSHIBA PC Diagnostic Tool displays the basic informati
187. r DVD R RW disc that was made with other software on a different DVD R RW or DVD R RW recorder Wi f you add data to a DVD R disc that you have already recorded to you might not be able to read the added data under some circumstances It cannot be read in 16 bit operating systems such as Windows 98SE and Windows ME In Windows NT4 you will need Service Pack 6 or later to read added data In Windows 2000 you will need Service Pack 2 or later to read it Some DVD ROM and CD RW DVD ROM drives cannot read added data regardless of the operating system E Drag n Drop CD DVD does not support recording to DVD RAM discs To record to a DVD RAM use Explorer or other utility Wi f you try to back up a DVD disc to a DVD RW disc that was erased by the Quick erase option you might get an error message Use the Full erase option to clear the DVD RW disc and try again W When you back up a DVD disc be sure the source drive supports recording to DVD R RW or DVD R RW discs If the source drive does not support recording to DVD R RW or DVD R RW discs it might not be backed up correctly W When you back up a DVD R DVD RW DVD R or DVD RW be sure to use the same type of disc Data Verification To verify that data is written or rewritten correctly follow the steps below before you write or rewrite a Data CD DVD 1 Right click Data BOX and select Options to display the DATA DISC Option window 2 Mark the Record and Verify check box and select
188. r with this chapter Knowing what might go wrong can help prevent problems from occurring solving process Resolving problems will be much easier if you observe the following guidelines B Stop immediately when you recognize a problem exists Further action may result in data loss or damage You may destroy valuable problem related information that can help solve the problem E Observe what is happening Write down what the system is doing and what actions you performed immediately before the problem occurred If you have a printer attached print a copy of the screen using PrtSc The questions and procedures offered in this chapter are meant as a guide they are not definitive problem solving techniques Many problems can be solved simply but a few may require help from your dealer If you find you need to consult your dealer or others be prepared to describe the problem in as much detail as possible Troubleshooting Preliminary checklist Consider the simplest solution first The items in this checklist are easy to fix and yet can cause what appears to be a serious problem W Make sure you turn on all peripheral devices before you turn on the computer This includes your printer and any other external device you are using Wi Before you attach an external device turn the computer off When you turn the computer back on it recognizes the new device E Make sure all options are set properly in the setup program W Che
189. rd gt under the palm rest if the flat cable was pulled out while you were removing the keyboard 13 Two screws secure the keyboard AR Be sure to use alltwo screws removed in step 7 Make sure no screw was dropped into the computer Make sure all foreign matter such as the tape applied in step 10 is removed 14 Seat the keyboard brace and press to secure latches 15 Install the battery pack Refer to Replacing the battery pack section in Chapter 6 Power and Power up Modes for details 16 Turn the power on and make sure the added memory is recognized Open System Properties in the Control Panel and click the General tab 8 8 User s Manual Optional Devices Removing memory module Main memory To remove the memory module make sure the computer is in boot mode then 1 Turn the computer off and remove all cables connected to the computer 2 Turn the computer upside down and remove the battery pack refer to Chapter 6 Power and Power Up Modes 3 Follow steps 4 through 9 in Installing memory module to access the memory module 4 Push the latches to the outside to release the module A spring will force one end of the module up 5 Grasp the sides of the module and pull it out then replace the insulator AR E fyou use the computer for a long time the memory modules and the circuits locating close to the memory modules will become hot In this case let them cool to room temperature before you r
190. reface Manual contents scc xo Ru rk RR OR RU ee ao xxi Conventions nena n x RR ene male EUR D aS xxii Abbreviations E wa ku en e asia ke xxii IGONS E T oe 2a eRe ee eee es SEA ae xxii Keys cud er dx ra bu rado ER EE eo ER ie xxii Key operation 000000 e xxiii Display nase Eus se buo ieu Eu Dans E TER Qa E xxiii MESSAGES sd a ne REED DEER IUE RUE ara Run ds die xxiii General Precautions Stress INJURY us bec t ees EE ae Be hee E XXV HeatinJUryz sse droe bela Oa eee cnt E EE E E E XXV Pressure or impact damage n susanna anana XXV PC card overheating nnana anaana xxvi Mobile phone 2 2 eere Eee EE uxor ede rn xxvi Central Processing Unit CPU Performance Disclaimer xxvi Chapter 1 Introduction Equipment checklist lleeeeeeeeeeeeene 1 1 Hardware cincina eade woe En ERE nee 1 1 SUI cH 1 2 FEATURES T u Dem 1 2 Special feat res iios eer eR aa daw eae ee RS Rena RR Un 7 1 10 Utilities Ak 1 13 OPTIONS inansa namana nn nn een 1 15 Chapter 2 The Grand Tour Front with the display closed llsssusls ss 2 1 keft side PE 2 2 Right Side 2 s tie ur We et a a a ein 2 3 Backside nee ae EE ee Auen 2 4 Underside cerei punisar enpi eee ae aaa 2 6 Front with the display open 0000 cece eee eee eee 2 8 System indicators 2 ser eR rb nh ham 2 10 Keyboard indicators
191. reign object Check whether the CD DVD is dirty If it is wipe it with a clean cloth dipped in water or a neutral cleaner See the Media care section in Chapter 4 for details on cleaning The software or hardware configuration may be causing a problem Make sure the hardware configuration matches your software s needs Check the CD DVD s documentation Check the type of CD DVD you are using The drive supports DVD ROM DVD ROM DVD Video CD ROM CD DA CD Text Photo CD single multi session CD ROM Mode 1 Mode 2 CD ROM XA Mode 2 Form1 Form2 Enhanced CD CD EXTRA CD G Audio CD only Addressing Method 2 Recordable CD CD R CD RW Check the region code on the DVD It must match that on the CD RW DVD ROM drive Region codes are listed in the Optical media drives section in Chapter 2 The Grand Tour If you have trouble writing make sure you are observing the following precautions Use only media recommended by TOSHIBA Do not use the mouse or keyboard during writing Use only the software supplied with the computer for recording Do not run or start other software during writing Do not jar the computer during writing Do not connect disconnect external devices or install remove internal cards during writing If problems persist contact your dealer User s Manual 9 9 Troubleshooting DVD Multi drive For more information refer to Chapter 4 Operating Basics Problem You cannot access a CD DVD i
192. res Do not write while virus check software is running Wait for it to finish and then disable virus detection programs including any software that checks files automatically in the background Do not use hard disk utilities including those intended to enhance HDD access speed They may cause unstable operation and data damage User s Manual Operating Basics Write from the computer s HDD to the CD DVD Do not try to write from shared devices such as a LAN server or any other network device Writing with software other than Drag n Drop CD DVD is not recommended When writing or rewriting Please observe consider the following when you write or rewrite to a CD R RW DVD R RW RAM or DVD R RW disc Do not perform any of the following actions when writing or rewriting Change users in the Windows XP operating system e Operate the computer for any other function including using a mouse or Touch Pad or closing opening the LCD panel e Start a communication application such as a modem Apply impact or vibration to the computer Install remove or connect external devices including the following PC card SD card USB devices external display i LINK devices optical digital devices Usethe Audio Video control button to reproduce music or voice Open the CD RW DVD ROM DVD R RW or DVD Multi drive Do not use standby hibernation while writing or rewriting Make sure writing or rewriting is completed before
193. res If these changes might affect your service or the operation of your equipment the telephone company will give you notice in writing to allow you to make any changes necessary to maintain uninterrupted service If problems arise If any of your telephone equipment is not operating properly you should immediately remove it from your telephone line as it may cause harm to the telephone network If the telephone company notes a problem they may temporarily discontinue service When practical they will notify you in advance of this disconnection If advance notice is not feasible you will be notified as soon as possible When you are notified you will be given the opportunity to correct the problem and informed of your right to file a complaint with the FCC In the event repairs are ever needed on your modem they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation Disconnection If you should ever decide to permanently disconnect your modem from its present line please call the telephone company and let them know of this change vi User s Manual User s Manual Fax branding The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission
194. resolution If you want to change the resolution follow the steps below 1 OpenDisplay properties and select the Settings tab 2 Select Advanced 3 Select the Adapter tab then select List all modes 4 Select a resolution from the menu Displaying movies on a TV or CRT This section describes how to set up your system to display movies simultaneously on your computer s internal LCD and on an external TV or CRT monitor Follow the steps below 1 Open the Control Panel and click Appearance and Themes 2 Click Display 3 Select the Settings tab and click Advanced button 4 Select the GeForce FX Go5200 32M 64M tab a Click the GeForce FX Go5200 32M 64M button b Click Overlay Controls in the small menu c From the Full Screen Device drop down menu select Primary Device or Secondary Device to enable movie display on an external TV or CRT monitor Primary Device Movies will be displayed full screen on the computer s internal LCD and in a window on the TV or CRT monitor Secondary Device Movies will be displayed full screen on the TV or CRT monitor and in a window on the computer s internal LCD Disable Movies will not be displayed on a TV or CRT monitor d Click OK User s Manual Optional Devices e Click OK in the Display Properties screen i LINK IEEE1394 Some models are equipped with a i LINK i LINK IEEE1394 is used for high speed data transfer for a range of compatible devices such as
195. rger The battery charger provides a convenient way to charge battery packs without requiring the use of your computer The battery charger holds up to two lithium ion battery packs Slim Select Bay HDD adaptor Black You can increase your computer s data storage capacity by installing an additional 30 GB 27 94 billion bytes 40 GB 37 26 billion bytes 60 GB 55 89 billion bytes or 80 GB 74 51 billion bytes hard disk drive in the Slim Select Bay To install an HDD in the Slim Select Bay HDD adaptor follow the steps below 1 Slide the lock to the unlock position and open the lid Figure 8 20 Opening the lid 2 Insert the HDD and push forward to ensure a firm connection Figure 8 21 Inserting the HDD User s Manual 8 15 Optional Devices 3 Close the lid and slide the lock to the lock position Figure 8 22 Closing the lid For details on inserting the Slim Select Bay HDD adaptor in the Slim Select Bay refer to Chapter 4 Operating Basics External monitor TV An external analog monitor can be connected to the external monitor port on the computer The computer supports VGA and Super VGA video modes To connect a monitor follow the steps below 1 Turn the computer off 2 Connect the monitor to the external monitor port 3 Turn the monitor s power on 4 Turn the computer on When you turn on the power the computer automatically recognizes the monitor and determines whether it is col
196. ria They are not guaranteed as the maximum weight of the actual product Size 314 w x 260 d x 31 5 34 9 h millimeters not including parts that extend beyond the main body Environmental Requirements Conditions Ambient temperature Relative humidity Operating 5 C 41 F to 35 C 95 F 20 to 80 Non operating 20 C 4 F to 65 C 149 F 10 to 95 Thermal Gradient 20 C per hour maximum Wet bulb 26 C maximum temperature Conditions Altitude from sea level Operating 60 to 3 000 meters Non operating 60 to 10 000 meters maximum User s Manual Specifications Power Requirements AC adaptor 100 240 volts AC 50 or 60 hertz cycles per second Computer 15 VDC 5 0 amperes Built in Modem Network control unit NCU Type of NCU AA Type of line Telephone line analog only Type of dialing Pulse Tone Control command AT commands EIA 578 commands Monitor function Computer s speaker Communication specifications Communication Data Full duplex system Fax Half duplex Communication Data protocol ITU T Rec V 21 V 22 V 22bis V 32 Former CCITT IN 32bis V 34 V 90 Bell 103 212A Fax ITU T Rec V 17N 29 V 27ter Former CCITT V 21 ch2 A 2 User s Manual Specifications Network control unit NCU Communication speed Transmitting level Receiving level Input output impedance Error correcting Data compression Power supply Data transmission and reception 300 1200 2400 480
197. rives you may experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices Also it is a good idea to make two or more copies of important data in case of undesired change or loss of the recorded contents User s Manual 4 11 Operating Basics Disclaimer DVD R tRW drive TOSHIBA does not bear responsibility for the following Damage to any CD R RW or DVD R RW R RW disc that may be caused by writing or rewriting with this product Any change or loss of the recorded contents of CD R RW or DVD R RW R RW disc that may be caused by writing or rewriting with this product or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents Damage that may be caused by using third party equipment or Software Given the technological limitations of current optical disc writing drives you may experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices Also it is a good idea to make two or more copies of important data in case of undesired change or loss of the recorded contents Before writing or rewriting Based on TOSHIBA s limited compatibility testing we suggest the following manufacturers of CD R RW and DVD R R RW RW RAM disc However in no event does TOSHIBA guarantee the operation quality or performance of any disc Disc quality can affect write or rewrite success rates
198. ro are not interchangeable E The Caps Lock function key locks only the alphabetic characters in uppercase while the shift lock on a typewriter places all keys in the shifted position EB The Shift keys the Tab key and the BkSp backspace key perform the same function as their typewriter counterparts but also have special computer functions User s Manual The Keyboard F1 F12 function keys The function keys not to be confused with Fn are the 12 keys at the top of your keyboard These keys function differently from other keys F1 Ye E g JE e ro Jt re a e om 3 so vo ad Mi ae EJ F1 through F12 are called function keys because they execute programmed functions when pressed Used in combination with the Fn key keys marked with icons execute specific functions on the computer See the section Soft keys Fn key combinations in this chapter The function executed by individual keys depends on the software you are using Soft keys Fn key combinations The Fn function is unique to TOSHIBA computers and is used in combination with other keys to form soft keys Soft keys are key combinations that enable disable or configure specific features z Some software may disable or interfere with soft key operations Soft key 1 settings are not restored by the Standby feature Emulating keys on enhanced keyboard E HAAA CAAA CAAA EEE EIS 77A Soo CCILL TEE zus Sr p uc C LC CH C24
199. rocessor and or main memory such as a printer or a mouse pixel A picture element The smallest dot that can be made on a display or printer Also called a pel plug and play A capability with Windows that enables the system to automatically recognize connections of external devices and make the necessary configurations in the computer port The electrical connection through which the computer sends and receives data to and from devices or other computers Power Saver Utility A TOSHIBA utility that lets you set the parameters for various power saving functions printed circuit board PCB A hardware component of a processor to which integrated circuits and other components are attached The board itself is typically flat and rectangular and constructed of fiberglass to form the attachment surface program A set of instructions a computer can execute that enables it to achieve a desired result See also application prompt A message the computer provides indicating it is ready for or requires information or an action from you Radio frequency interference RFI shield A metal shield enclosing the printed circuit boards of the printer or computer to prevent radio and TV interference All computer equipment generates radio frequency signals The FCC regulates the amount of signals a computing device can allow past its shielding A Class A device is sufficient for office use Class B provides a more stringent classification for ho
200. roperly if W itis compatible with the modem at the other end of the call and W the application using the modem is compatible with the application at the other end of the call e g accessing the Internet requires suitable software in addition to a modem This equipment shall not be used in any manner which could constitute a nuisance to other Telecom customers Some parameters required for compliance with Telecom s PTC Specifications are dependent on the equipment PC associated with this modem The associated equipment shall be set to operate within the following limits for compliance with Telecom Specifications E There shall be no more than 10 call attempts to the same number within any 30 minute period for any single manual call initiation and W The equipment shall go on hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next B Automatic calls to different numbers shall be not less than 5 seconds apart Immediately disconnect this equipment should it become physically damaged and arrange for its disposal or repair The correct settings for use with this modem in New Zealand are as follows ATBO CCITT operation AT amp G2 1800 Hz guard tone AT amp P1 Decadic dialing make break ratio 33 67 ATSO 0 not auto answer ATS6 4 Blind dial delay ATS7 7less than 90 Time to wait to carrier after dialing ATS10 less than 150 loss of carrier to hangup delay factor
201. rrier Detect DCD control Data Carrier Detect is a signal from the modem to the computer indicating that a carrier signal is being received from a remote modem DCD normally turns off when the modem no longer detects the carrier signal amp C0 The state of the carrier from the remote modem is ignored DCD circuit is always on amp C1 DCD turns on when the remote modem s carrier signal is detected and off when the carrier signal is not detected default Result Codes OK n 0 1 ERROR Otherwise amp Dn DTR control This command interprets how the modem responds to the state of the DTR signal and changes to the DTR signal amp DO Ignore The modem ignores the true status of DTR and treats it as always on This should only be used if your communication software does not provide DTR to the modem amp D1 Ifthe DTR signal is not detected while in on line data mode the modem enters command mode issues an OK result code and remains connected C 6 User s Manual AT Commands amp D2 Ifthe DTR signal is not detected while in on line data mode the modem disconnects default amp D3 Reset on the on to off DTR transition Result Codes OK n 0 1 2 3 ERROR Otherwise amp FLoad factory settings amp Gn amp Kn amp Pn This command loads the configuration stored and programmed at the factory This operation replaces all of the command options and the S register settings in the active configuration with factory
202. ry is fully charged No light Under any other conditions the indicator does not light If the battery becomes too hot while it is being charged the charge will 1 stop and the battery indicator will go out When the battery s temperature falls to a normal range charge will resume This occurs whether the computer s power is on or off DC IN 15V indicator Check the DC IN 15V indicator to determine the power status with the AC adaptor connected Green Indicates the AC adaptor is connected and supplying proper power to the computer Flashing orange Indicates a problem with the power supply Plug the AC adaptor into another outlet If it still does not operate properly contact your dealer No light Under any other conditions the indicator does not light 6 4 User s Manual Power and Power Up Modes Power indicator Check the Power indicator to determine the power status Green Indicates power is being supplied to the computer and the computer is turned on Blinking orange Indicates power is being supplied to the computer while the computer is in Standby mode The indicator turns on for one second and off for two seconds No light Under any other conditions the indicator does not light Battery types The computer has three types of batteries Wi Battery packs Main 2nd option and High capacity option W Real Time Clock RTC battery Main battery When the AC adaptor is not connected the computer
203. s V 42 error control and V 42bis data compression V 42 V 42 error control only MNP 5 MNP class 4 error control and MNP class 5 data compression MNP 4 MNP class 4 error control only NoEC No error control protocol 2 In some countries regions these result codes may not appear User s Manual D 7 S registers D 8 User s Manual TECRA M2 Appendix E V 90 The TOSHIBA internal modem uses V 90 technology The modem is capable of downstream speeds of 56Kbps kilobits per second when connected to an Internet service provider that supports V 90 As with any modem the actual throughput speed of data transfer depends on analog telephone line conditions which can vary considerably Therefore many users will experience throughput in the range of 28 50Kbps under normal telephone line conditions Upstream data flows at the V 34 rate V 90 rates can be achieved only when one V 90 capable host modem is connected to another The TOSHIBA Internal modem will select automatically V 34 if the remote modem lacks V 90 capability or if a combination of network and or phone line conditions prevent V 90 pie connection V 90 mode Function Transmission speed Data V 90 From 56K maximum to 28Kbps minimum Reception only User s Manual V 90 No 70 72 74 76 78 80 82 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 Ta
204. s Fn F5 to change the active display device When you press these hot keys a dialog box appears Only selectable devices will be displayed Hold down Fn and press F5 again to change the device When you release Fn and F5 the selected device will change If you hold down these hot keys for five seconds the selection will return to LCD 5 4 User s Manual The Keyboard T 1 Fl ca LCD Display Brightness Pressing Fn F6 decreases the display brightness in decrements When you press these hot keys the current setting will be displayed for two seconds by an icon You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver E ca LCD Display Brightness Pressing Fn F7 increases the display brightness in increments When you press these hot keys the current setting will be displayed for two seconds by a pop up icon You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver m The brightness level is always set at the maximum value for about 18 seconds when the LCD turns on After 18 seconds the brightness level will appear at the Power Save Mode setting or you can change it manually m Display clarity increases with the brightness level Aes Wireless setting If your computer has both Bluetooth and wireless LAN functions you can press Fn F8 to select which type of wireless communication you want to
205. s in this section carefully to ensure safe operation and maximum performance Safety precautions Mishandling of batteries can cause death serious injury or property damage Carefully observe the following advisories Danger Indicates an imminently hazardous situation which could result in death or serious injury if you do not follow instructions Warning Indicates a potentially hazardous situation which could result in death or serious injury if you do not follow instructions Caution Indicates a potentially hazardous situation which if not avoided may result in moderate or minor injury or property damage Note Provides important information Danger 1 Never try to dispose of the battery pack by burning or expose it to a heating device such as a microwave oven The battery pack could explode and cause bodily injury 2 Never try to disassemble repair or otherwise tamper with a battery pack The battery pack will overheat and ignite Leakage of caustic alkaline solution or other electrolytic substances will cause fire or injury possibly resulting in death or serious injury 3 Never short circuit the battery pack by contacting the terminals with a metal object A short circuit can cause fire or otherwise damage the battery pack and possibly cause injury To avoid accidental short circuit always wrap the battery pack in plastic and cover the terminals with electrical tape when storing or disposing of the battery pack
206. s main power source is a removable lithium ion battery pack also referred to in this manual as the main battery You can purchase additional battery packs for extended use of the computer away from an AC power source Before you remove the battery pack set the computer to Hibernation mode or save your data and shut down the computer Do not change the battery pack while the AC adaptor is connected W The battery pack is a lithium ion battery which can explode if not properly replaced used handled or disposed of Dispose of the battery as required by local ordinances or regulations Use only batteries recommended by TOSHIBA as replacements E Do not remove the battery pack while the computer is in Standby mode Data is stored in RAM so if the computer loses power it will be lost When the computer is powered off in Standby mode and the AC adaptor is not connected the main battery pack and optional 2nd battery pack supply power to maintain data and program in memory If the battery pack s is completely discharged Standby mode does not function and the computer loses all data in memory To ensure that the battery pack maintains its maximum capacity operate the computer on battery power at least once a month until the battery pack is fully discharged Refer to Extending battery life in this chapter for procedures If the computer is continuously operated on AC power through an AC adaptor for an extended period more than a month the batter
207. scribes how to connect disconnect to a LAN Do not install or remove an optional memory module while Wake up on LAN is enabled The Wake up on LAN function consumes power even when the system is off Leave the AC adaptor connected while using this feature LAN cable types The computer must be configured properly before connecting to a LAN Logging onto a LAN using the computer s default settings could cause a malfunction in LAN operation Check with your LAN administrator regarding set up procedures If you are using Gigabit Ethernet LAN 1000 megabits per second 1000BASE T be sure to connect with a CAT5E cable or higher You cannot use a CAT3 or CAT5 cable If you are using Fast Ethernet LAN 100 megabits per second 100BASETX be sure to connect with a CAT5 cable or highter You cannot use a CAT3 cable 4 24 User s Manual Operating Basics If you are using Ethernet LAN 10 megabits per second 10BASE T you can connect with a CAT3 or highter Connecting LAN cable To connect the LAN cable follow the steps below 1 Turn off the power to the computer and to all external devices connected to the computer 2 Plug one end of the cable into the LAN jack Press gently until you hear the latch click into place Figure 4 13 Connecting the LAN cable 3 Plug the other end of the cable into a LAN hub connector Check with your LAN administrator before connecting to a hub 1 When the computer is exchanging
208. ser s Manual Getting Started AR E Use only the AC adaptor supplied with your computer or an equivalent adaptor that is compatible Use of any incompatible adaptor could damage your computer TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor BW When you connect the AC adaptor to the computer always follow the steps in the exact order as described in the User s Manual Connecting the power cable to a live electrical outlet should be the last step otherwise the adaptor DC output plug could hold an electrical change and cause an electrical shock or minor bodily injury when touched As a general safety precaution avoid touching any metal parts 1 Connect the power cord to the AC adaptor Figure 3 2 Connecting the power cord to the AC adaptor 2 Connect the AC adaptor s DC output plug to the DC IN 15V input port on the back of the computer DC IN 15V Figure 3 3 Connecting the adaptor to the computer 3 Plug the power cord into a live wall outlet The Battery and DC IN 15V indicators on the front of the computer should glow Opening the display The display panel can be rotated in a wide range of angles for optimal viewing 1 Slide the display latch on the front of the computer to the right 2 Liftthe panel up and adjust it to the best viewing angle for you User s Manual 3 5 Getting Started Use reasonable care when opening and closing the display panel Opening it vigorous
209. sing the overlay keys type the ASCII code 3 Release Alt and the ASCII character appears on the display screen With the overlay off 1 Hold down Alt Fn 2 Using the overlay keys type the ASCII code 3 Release Alt Fn and the ASCII character appears on the display Screen 5 8 User s Manual TECRA M2 Chapter 6 Power and Power Up Modes The computer s power resources include the AC adaptor and internal batteries This chapter gives details on making the most effective use of these resources including charging and changing batteries tips for saving battery power and power up modes Power conditions The computer s operating capability and battery charge status are affected by the power conditions whether an AC adaptor is connected whether a battery is installed and what the charge level is for the battery Table 6 1 Power conditions Power on Power off no operation AC Main Battery Operates No charge adaptor fully charged No charge LED Battery green connected LED Battery green DC IN 15V green DC IN 15V green Main Battery Operates e Quick charge Mabel Charge LED Battery orange no a LED Battery orange DC IN 15V green DC IN 15V green No Main battery Operates No charge installed No charge LED Battery off LED Battery off DC IN 15V green DC IN 15V green User s Manual Power and Power Up Modes AC 2nd battery fully adaptor charged connected 2nd Battery
210. t ECP For most printers the port should be set to ECP Default Standard This setting should be used with some other Bi directional parallel devices Display This tab lets you customize your computer s display settings for either the internal LCD screen or for an external monitor Power On Display Lets you use the display to be used when the computer is booted This setting is only available on Standard VGA mode and not available on Windows Desktop Auto Selected Selects an external monitor if one is connected Otherwise it selects the internal LCD Default LCD Analog RGB Selects both the internal LCD and external monitor for simultaneous display 7 2 User s Manual HW Setup CPU This function lets you set the CPU operating mode Dynamic CPU Frequency Mode This option lets you choose from the following settings Dynamically Switchable Always High Always Low CPU power consumption and clock speed automatic switching function is enabled When the computer is in use CPU operation is automatically switched when necessary Default CPU power consumption and clock speed automatic switching function is disabled The CPU always runs at its fastest speed CPU power consumption and clock speed automatic switching function is disabled The CPU always runs at low power consumption and low speed User s Manual 7 3 HW Setup Boot Priority Boot Priority Options This option sets
211. t The parameter value automatically selected by the system when you or the program do not provide instructions Also called a preset value User s Manual Glossary 5 Glossary delete To remove data from a disk or other data storage device Synonymous with erase device driver A program that controls communication between a specific peripheral device and the computer The CONFIG SYS file contains device drivers that MS DOS loads when you turn the computer on dialog box A window that accepts user input to make system settings or record other information disk drive The device that randomly accesses information on a disk and copies it to the computer s memory It also writes data from memory to the disk To accomplish these tasks the unit physically rotates the disk at high speed past a read write head disk storage Storing data on magnetic disk Data is arranged on concentric tracks much like a phonograph record display A CRT LCD or other image producing device used to view computer output documentation The set of manuals and or other instructions written for the users of a computer system or application Computer system documentation typically includes procedural and tutorial information as well as system functions DOS Disk Operating System See operating system driver A software program generally part of the operating system that controls a specific piece of hardware frequently a peripheral device
212. t another 20 minutes before turning on the computer If the indicator still does not glow the battery may be at the end of its operating life Replace it If you do not think the battery is at the end of its operating life see your dealer If you frequently recharge a partially charged battery the battery might not charge to its full potential Fully discharge the battery then try to charge it again Check the power consumption settings in Power Saver utility Consider using a power saving mode Procedure Refer to the TOSHIBA Password Utility section in Chapter 6 Power and Power Up Modes 9 6 User s Manual Troubleshooting Keyboard Keyboard problems can be caused by your setup configuration For more information refer to Chapter 5 The Keyboard Problem Some letter keys produce numbers Output to screen is garbled LCD panel Procedure Check that the numeric keypad overlay is not selected Press Fn F10 and try typing again Make sure the software you are using is not remapping the keyboard Remapping involves reassigning the meaning of each key See your software s documentation If you are still unable to use the keyboard consult your dealer Apparent LCD problems may be related to the computer s setup Refer to Chapter 7 HW Setup for more information Problem No display Problems above remain unresolved or other problems occur Hard disk drive Problem Computer does n
213. tal damage Cover the terminals with electrical tape to prevent short circuits which could cause the battery pack to ignite or rupture Use only battery packs recommended by TOSHIBA as replacements Always make sure the battery pack is installed correctly and securely Otherwise a battery pack could fall out and possibly cause injury Charge the battery pack only in an ambient temperature between 5 and 35 degrees Celsius Otherwise the electrolyte solution might leak battery pack performance might deteriorate and the battery life might be shortened 6 8 User s Manual Power and Power Up Modes 6 Be sure to monitor the remaining battery power Ifthe battery pack and real time clock battery discharge completely Standby and Suspend will not function and data in memory will be lost Also the computer might register an incorrect time and date In this case connect the AC adaptor to recharge the batteries 7 Never install or remove the battery pack without first turning off the power and disconnecting the AC adaptor Never remove the battery pack while the computer is in Suspend or Standby mode Data will be lost Note 1 Never remove the battery pack while the Wake up on LAN function is enabled Data will be lost Before you remove a battery pack disable the Wake up on LAN function 2 To ensure the battery pack maintains maximum capacity operate the computer on battery power once a week until the battery pack is full
214. tems or manipulate text and graphics designated by the on screen pointer A Touch Pad located in the center of the palm rest is used to control the on screen pointer Refer to the Using the Touch Pad section in Chapter 4 Operating Basics Control buttons below the keyboard let you select menu items or manipulate text and graphics designated by the on screen pointer A pointer control device located in the center of the keyboard is used to control the on screen pointer Refer to the Using the AccuPoint section in Chapter 4 Operating Basics Press this button to change internal display simultaneous display or multi monitor display The default setting is the simultaneous display on LCD and CRT with resolution of 1024 X 768 When you press this button twice the display mode returns to single display on LCD only Setting of multi monitor display in Windows XP PC changes its display mode to the multi monitor display on LCD and CRT You can also return to single display by pressing this button twice The setting of TOSHIBA Presentation button can be changed through the property of TOSHIBA Console Display mode is changed to the multi monitor display by selecting Different Image Windows XP only or to the simultaneous display on internal and external display by selecting Same Image Press this button to launch an application automatically The default is TOSHIBA Console User s Manual 2 9 The Grand Tour
215. tery pack E Slim Select Bay 2nd battery pack W Additional AC adaptor E Battery charger Peripheral devices Slim Select Bay HDD adaptor External monitor TV i LINK IEEE1394 Advanced Port Replicator III Other B Security lock User s Manual Optional Devices PC cards The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type Il card Any PC card that meets industry standards manufactured by TOSHIBA or other vendor can be installed The slot supports 16 bit PC cards including PC card 16 s multifunction card and CardBus PC cards CardBus supports the new standard of 32 bit PC cards The bus provides superior performance for the greater demands of multimedia data transmission Inserting a PC card T The PC card connector is located on the left side of the computer Windows hot install feature lets you insert PC cards while the computer s power is on W Do notinsert a PC card while the computer is in standby or hibernation mode Some cards might not work properly W An HDD or CD ROM connected to a 16 bit PC card might affect the performance of the computer s sound system and data transmission including slower transmission speeds and dialing errors To insert a PC card follow the steps below 1 Insert the PC card 2 Press gently to ensure a firm connection PC card Figure 8 1 Inserting the PC card After inserting the card refer to the card s documentation and
216. the screw in the Slim Select Bay lock is set in the hole for the unlock position 5 Slide the Slim Select Bay latch to the unlock position 4 4 User s Manual Operating Basics 6 Grasp the DVD ROM drive and slide it out NV The DVD ROM drive and other Slim Select Bay modules can become hot with use Be careful when removing the module Lock Screw Silm Select Silm Select Bay Bay Latch M odule AQ A Figure 4 4 Removing the Slim Select Bay HDD adaptor Inserting a module Insert the Slim Select Bay HDD adaptor as described below 1 Insert the Slim Select Bay HDD adaptor in the computer as shown below and press until the ejector clicks 2 If you want to lock the Slim Select Bay module set the Slim Select Bay lock screw in the hole for the lock position The lock screw is inserted in the unlock position at the time of purchasing Lock Screw Figure 4 5 Inserting the Slim Select Bay HDD adaptor Silm Select Bay Module User s Manual 4 5 Operating Basics Using optical media drives T The text and illustrations in this section refer primarily to the optional DVD ROM drive However operation is the same for other optical drive in the Slim Select Bay The full size drive provides high performance execution of CD DVD ROM based programs You can run either 12 cm 4 72 or 8 cm 3 15 CD DVDs without an adaptor An ATAPI interface controller is used for CD DVD
217. this case TOSHIBA Power Saver will indicate a 10096 charge for both the old and new battery but the displayed estimated time remaining will be shorter for the older battery Maximizing battery operating time A battery s usefulness depends on how long it can supply power on a single charge How long the charge lasts in a battery depends on B How you configure the computer for example whether you enable battery power saving options The computer provides a battery save mode which can be set in TOSHIBA Power Saver to conserve battery power This mode has the following options CPU Precessing speed Screen brightness Cooling Method System standby System Hibernation Monitor Power off HDD Power off W How often and how long you use the hard disk optical disc and the floppy disk drive B How much charge the battery contained to begin with W How you use optional devices such as a PC card to which the battery supplies power W Enabling Standby mode conserves battery power if you are frequently turning the computer off and on B Where you store your programs and data W Closing the display when you are not using the keyboard saves power E Operating time decreases at low temperatures W The condition of the battery terminals Make sure the battery terminals stay clean by wiping them with a clean dry cloth before installing the battery pack User s Manual 6 11 Power and Power Up Modes Ret
218. tic electrolyte fluid should contact your eyes immediately wash your eyes with large amounts of running water and seek medical attention to help prevent eye damage If electrolyte fluid should contact your skin immediately wash it under running water to prevent rash If it contacts your clothes promptly remove them to prevent the fluid from contacting your skin or eyes Immediately turn off the power disconnect the AC adaptor and remove the battery if any of the following events are observed in the battery pack offensive or unusual odor excessive heat discoloration or deformation Never use the computer again until it has been checked by a TOSHIBA service provider It might generate smoke or fire or the battery pack might rupture Make sure the battery is securely installed in the computer before attempting to charge the battery pack Improper installation could generate smoke or fire or cause the battery pack to rupture Keep the battery pack out of reach of infants and children It can cause injury Caution 1 Never continue to use a battery pack after its recharging capacity has become impaired or after the display of a warning message indicating that the battery pack s power is exhausted Continued use of an exhausted or impaired battery pack could cause the loss of data Never dispose of battery packs with normal trash Bring them to your TOSHIBA dealer or to another recycling center to save resources and prevent environmen
219. to the online help files for Appendix C AT Commands The computer will automatically cut off communication when connection with the carrier is not successful for a set time interval Try lengthening this time interval Check the error control setting in your communications application You can also use the AT N command Refer to the online help files for Appendix C AT Commands In data transmission make sure the parity bit and stop bit settings correspond with those of the remote computer Check the flow control and communication protocol Check the rings before auto answer setting in your communications application You can also use the ATSO command Refer to the online help files for Appendix D S registers If problems persist contact your dealer Procedure Check for a firm cable connection between the LAN jack and the LAN HUB Make sure the AC adaptor is connected The Wake up on LAN function consumes power even when the system is off If problems persist consult your LAN administrator 9 18 User s Manual Troubleshooting Wireless LAN If the following procedures do not restore LAN access consult your LAN administrator For more information on wireless communication refer to Chapter 4 Operating Basics Problem Procedure Cannot access Make sure the computer s wireless Wireless LAN communication switch is set to on If problems persist contact your LAN administrator Cannot access Mak
220. tokens 6 16 User s Manual Power and Power Up Modes Supervisor password If you set a supervisor password some functions might be restricted when a user logs on with the user password To set a supervisor password execute the file TOSUP EXE The file is located at C Program Files Toshiba Windows Utilities SVPWTool TOSUP EXE This utility lets you do the following W Register delete or change the supervisor password E Create or invalidate a supervisor password token This function in the TOSHIBA Password Utility lets you invalidate only I supervisor tokens or all tokens including user and supervisor tokens W Specify restrictions for general users Starting the computer by password If you registered a password there are two ways to start the computer Wi Insert a token before you turn on the computer The computer will start normally without displaying a password prompt E Enter the password manually oT The password is necessary only if the computer was shut down in boot 1 mode It is not needed in Hibernation or Standby mode To enter a password manually follow these steps 1 Turn on the power as described in Chapter 3 Getting Started The following message will appear in the LCD Password 2 Enter the Password 3 Press Enter 1 If you enter the password incorrectly three times in a row the computer shuts off In this case you must turn the computer back on to retry password entry
221. tor glows the keyboard is in all caps mode Caps Lock Indicator Figure 2 9 Caps Lock indicator Caps Lock This indicator glows green when the alphabet keys are locked in uppercase Arrow mode When the Arrow mode indicator lights green ty you can use the keypad overlay gray labeled keys as cursor keys Refer to the Keypad overlay section in Chapter 5 The Keyboard Numeric mode You can use the keypad overlay gray labeled A keys for numeric input when the Numeric mode indicator lights green Refer to the Keypad overlay section in Chapter 5 The Keyboard 2 12 User s Manual The Grand Tour USB floppy disk drive A 3 1 2 floppy disk drive accommodates 1 44 megabyte or 720 kilobyte floppy disks It connects to the USB port Disk In Use Indicator Floppy disk Eject button slot Figure 2 10 USB floppy disk drive Disk In Use This indicator lights when the floppy disk is being Indicator accessed Floppy disk slot Insert a floppy disk in this slot Eject button When a floppy disk is fully seated in the drive the eject button pops out To remove a floppy disk push in the eject button and the floppy disk pops out partially for removal AR Check the Disk In Use indicator when you use the floppy disk drive Do not press the eject button or turn off the computer while the light is glowing Doing so could destroy data and damage the floppy disk or the drive 2 W The external floppy disk drive should be place
222. truction Extended Capability Port An industry standard that provides a data buffer switchable forward and reverse data transmission and run length encoding RLE support F fast infrared An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps file A collection of related information a file can contain data programs or both firmware A set of instructions built into the hardware which controls and directs a microprocessor s activities floppy disk A removable disk that stores magnetically encoded data Also called a floppy disk floppy disk drive FDD An electromechanical device that reads and writes to floppy disks See also floppy disk Fn esse A TOSHIBA utility that lets you assign functions to hot keys folder An icon in Windows used to store documents or other folders format The process of readying a blank disk for its first use Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk function keys The keys labeled F1 through F12 that tell the computer to perform certain functions G gigabyte GB A unit of data storage equal to 1024 megabytes See also megabyte graphics Drawings pictures or other images such as charts or graphs to present information hard disk A non removable disk usually referred to as drive C The factory installs this disk and only a trained engineer
223. uch as the terminal printer and disk drives and the settings that define how your system works You use the HW Setup program to control your system configuration control keys A key or sequence of keys you enter from the keyboard to initiate a particular function within a program controller Built in hardware and software that controls the functions of a specific internal or peripheral device e g keyboard controller co processor A circuit built into the processor that is dedicated to intensive math calculations CPS Characters Per Second Typically used to indicate the transmission speed of a printer CPU Central Processing Unit The portion of the computer that interprets and executes instructions CRT Cathode Ray Tube A vacuum tube in which beams projected on a fluorescent screen producing luminous spots An example is the television set cursor A small blinking rectangle or line that indicates the current position on the display screen data Information that is factual measurable or statistical that a computer can process store or retrieve data bits A data communications parameter controlling the number of bits binary digits used to make up a byte If data bits 7 the computer can generate 128 unique characters If data bits 8 the computer can generate 256 unique characters DC Direct Current Electric current that flows in one direction This type of power is usually supplied by batteries defaul
224. unications Equipment Gress A02 0604JP T User s Manual User s Manual Pursuant to FCC CFR 47 Part 68 When you are ready to install or use the modem call your local telephone company and give them the following information E The telephone number of the line to which you will connect the modem W The registration number that is located on the device The FCC registration number of the modem will be found on either the device which is to be installed or if already installed on the bottom of the computer outside of the main system label W The Ringer Equivalence Number REN of the modem which can vary For the REN of your modem refer to your modems label The modem connects to the telephone line by means of a standard jack called the USOC RJ11C Type of service Your modem is designed to be used on standard device telephone lines Connection to telephone company provided coin service central office implemented systems is prohibited Connection to party lines service is subject to state tariffs If you have any questions about your telephone line such as how many pieces of equipment you can connect to it the telephone company will provide this information upon request Telephone company procedures The goal of the telephone company is to provide you with the best service it can In order to do this it may occasionally be necessary for them to make changes in their equipment operations or procedu
225. urity 1 Be sure to enable WEP encryption function Otherwise your computer will allow the illegal access by outsider through wireless LAN to cause illegal intrusion eavesdropping and loss or destruction of stored data TOSHIBA strongly recommend the customer to enable the WEP function TOSHIBA is not liable for the eavesdropping of data due to the use of wireless LAN and the damage thereof 4 22 User s Manual Operating Basics Bluetooth wireless technology Bluetooth wireless technology eliminates the need for cables between electronic devices such as desktop computers printers and mobile phones You cannot use the built in Bluetooth functions and an optional Bluetooth SD card 2 simultaneously Bluetooth wireless technology has the following features Worldwide operation The Bluetooth radio transmitter and receiver operate in the 2 4 GHz band which is license free and compatible with radio systems in most countries in the world Radio links You can easily establish links between two or more devices The link is maintained even if the devices are not within line of sight Security Two advanced security mechanisms ensure a high level of security Authentication prevents access to critical data and makes it impossible to falsify the origin of a message E Encryption prevents eavesdropping and maintains link privacy Wireless communication switch You can enable or disable wireless LAN and Bluet
226. ury or damage to the computer Be certain to read the general precautions below and to note the cautions included in the text ofthe manual Stress injury Carefully read the Instruction Manual for Safety amp Comfort It contains information on prevention of stress injuries to your hands and wrists than can be caused by extensive keyboard use Chapter 3 Getting Started also includes information on workspace design posture and lighting that can help reduce physical stress Heat injury E Avoid prolonged physical contact with the computer If the computer is used for long periods its surface can become very warm While the temperature will not feel hot to the touch if you maintain physical contact with the computer for a long time if you rest the computer on your lap or if you keep your hands on the palm rest for example your skin might suffer low heat injury E ifthe computer has been used for a long time avoid direct contact with the metal plate supporting the I O ports It can become hot Wi The surface of the AC adaptor can become hot when in use This condition does not indicate a malfunction If you need to transport the AC adaptor disconnect it and let it cool before moving it E Do not lay the AC adaptor on a material that is sensitive to heat The material could be damaged Pressure or impact damage Do not apply heavy pressure to the computer or subject it to strong impact Excessive pressure or impact can cause dama
227. use When you press these hot keys a dialog box will appear Continue holding down Fn and press F8 to change the setting If wireless communication is turned off Disabled Wireless Communication Switch will be displayed If no wireless communication device is installed no dialog box will appear aB Dual Pointing Device Pressing Fn F9 in a windows environment enables or disables the Dual Pointing Device function When you press these hot keys the current setting will change and be displayed as an icon User s Manual 5 5 The Keyboard f Space Display resolution selection Press Fn space keys to change the display resolution Each time when you press these hot keys the display resolution changes as follows From the current resolution the original resolution to 1024X768 from 1024X768 to 800X600 from 800X600 to the original resolution aga TOSHIBA Zooming Ulitity reduce To reduce the icon size on the desktop or the application window press the 1 key while holding down the Fn key aga TOSHIBA Zooming Ulitity enlarge To enlarge the icon size on the desktop or the application window press the 2 key while holding down the Fn key Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky that is you can press it once release it and then press an F number key To start the TOSHIBA Accessibility Utility click start point to All Programs point to TOSHIBA poi
228. uter 2000 eee eee eee eee 3 10 Restoring the preinstalled software from the Product Recovery DVD ROM llessssss 3 11 Chapter 4 Operating Basics TOSHIBA Dual Pointing Device leeseeeeeeeeeee 4 1 Using the Touch Pad 0 eee eee 4 2 Using the AccuPoint 1 0 0 0 e tees 4 2 AccuPoint precautions 0 llic eee 4 2 Replacing the cap 0 0 4 2 Using the USB floppy disk drive lesser 4 3 Connecting 3 1 2 floppy disk drive lle 4 3 Disconnecting 3 1 2 floppy disk drive llle 4 4 Changing Slim Select Bay modules Lees 4 4 Removing a module 0 00 c eee eee eee 4 4 Inserting a module 0 00000 eee 4 5 xiv User s Manual Table of Contents Using optical media drives 0 0 e rennen nun nen 4 6 Loading discs csse bl E Ep 4 6 Removing discs 4 8 Writing CDs on CD RW DVD ROM drive 00e eee eeeee 4 9 Before writing or rewriting 1 2 0 0 cee ee eee 4 9 When writing or rewriting 0 0 0 een 4 10 Writing CD DVDs on DVD Multi drive esses 4 11 Writing CD DVDs on DVD R RW drive DVD Dual drive 4 11 Important message DVD Multi drive 222222222 4 11 Important message DVD R RW drive 22 222222 nennen 4 11 Disclaimer DVD Multi drive 22 2222 c onen 00 nenn 4 11 Disclaimer DVD R RW drive 2 2
229. wer supply Battery save mode Panel power on off Low battery automatic hibernation This feature automatically cuts off power to the hard disk drive when it is not accessed for a time specified Power is restored when the hard disk is accessed You can specify the time in the HDD power off item of the Basic Setup tab in TOSHIBA Power Saver This feature automatically shuts down the system in standby mode or Hibernation mode when there is no input or hardware access for a time specified You can specify the time and select either System Standby or System hibernation in the System standby and System item of the Basic Setup tab in TOSHIBA Power Saver A ten key pad is integrated into the keyboard Refer to the Keypad overlay section in Chapter 5 The Keyboard for instructions on using the keypad overlay Two levels of password security supervisor and user are available to prevent unauthorized access to your computer A hot key function blanks the screen and disables the computer providing data security A microprocessor in the computer s intelligent power supply detects the battery s charge and calculates the remaining battery capacity It also protects electronic components from abnormal conditions such as voltage overload from an AC adaptor You can monitor remaining battery capacity Use the Battery remaining item in TOSHIBA Power Saver This feature lets you save battery power You can specify the Power Save Mode in
230. y Universal Two Universal Serial Bus ports are on the left e lt gt Serial Bus side The ports comply with the USB 2 0 standard which enables data transfer speeds 40 USB 2 0 ports times faster than the USB 1 1 standard The ports also support USB 1 1 AR Keep foreign objects out ofthe USB connectors A pin or similar object can damage the computer s circuitry Operation of all functions of all USB devices has not been confirmed 1 Some functions might not execute properly Backside Figure 2 4 shows the computer s back panel Video out jack DC IN 15V Modem jack LAN active Link indicator indicator orange green Figure 2 4 The backside of the computer LAN jack Video out jack Plug an S Video cable into this jack for video out S2 The S Video cable carries video signal Modem jack In areas where an internal modem is installed as standard equipment there is a modem jack that lets you use a modular cable to connect the modem directly to a telephone line AR E ncase of a lightning storm unplug the modem cable from the telephone jack W Do not connect the modem to a digital telephone line A digital line will damage the modem 2 4 User s Manual The Grand Tour oco DC IN 15V EJ DC IN 15V LAN jack Link indicator green LAN active indicator orange The AC adaptor connects to this socket Use only the model of AC adaptor that comes with the computer
231. y default of 15 recommended ATS11 90 DTMF dialing on off duration 90 ms ATX2 Dial tone detect but not U S A call progress detect User s Manual User s Manual B When used in the Auto Answer mode the SO register must be set with a value of 3 or 4 This ensures E aperson calling your modem will hear a short burst of ringing before the modem answers This confirms that the call has been successfully switched through the network W caller identification information which occurs between the first and second ring cadences is not destroyed W The preferred method of dialing is to use DTMF tones ATDT as this is faster and more reliable than pulse decadic dialing If for some reason you must use decadic dialing your communications program must be set up to record numbers using the following translation table as this modem does not implement the New Zealand Reverse Dialing standard Number to be dialed 0 123456789 Number to program into computer 0987654321 Note that where DTMF dialing is used the numbers should be entered normally W The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal Before reporting such occurrences as faults please check the line with a standard Telepermitted telephone and only report a fault if the phone performance is impaired E itis recommended that this equipment be disconnected from
232. y discharged Refer to the section Extending battery life in this chapter for procedures If the computer is continuously operated on AC power for an extended period more than a week the battery might fail to retain a charge It might not function efficiently over the expected life of the battery pack and the Battery indicator might not indicate a low battery condition 3 After the battery pack is charged avoid leaving the AC adaptor connected and the computer turned off for more than a few hours at a time Continuing to charge a fully charged battery pack can damage the battery Charging the batteries i A When the power in the battery pack becomes low the Battery indicator flashes orange indicating that only a few minutes of battery power remain If you continue to use the computer while the Battery indicator flashes the computer enables Hibernation mode so you don t lose data and automatically turns off The computer enters Hibernate mode only if Hibernation is enabled in two places the Hibernate tab in Power Options and Setup Action tab in TOSHIBA Power Saver You must recharge a battery pack when it becomes discharged Procedures To recharge a battery pack while it is installed in the computer connect the AC adaptor to the DC IN 15V socket and plug the other end into a working outlet The Battery indicator glows orange when the battery is being charged Use only the computer connected to an AC power source or the
233. y may fail to retain a charge It may not function efficiently over the expected life of the battery and the Battery indicator may not indicate a low battery condition User s Manual 6 5 Power and Power Up Modes 2nd battery option A An optional 2nd battery can be installed in the Slim Select Bay to increase your battery operating time Note the caution on Standby mode in the previous section Main battery The 2nd battery pack is a lithium ion battery which can explode if not properly replaced used handled or disposed of Dispose of the battery as required by local ordinances or regulations Use only batteries recommended by TOSHIBA as replacements High capacity battery An optional High capacity battery is installable instead of a main battery The capacity of High capacity battery is approximately double the capacity of main battery The connection method of High capacity battery is the same as that of main battery W The battery pack is a lithium ion battery which can explode if not properly replaced used handled or disposed of Dispose of the battery as required by local ordinances or regulations Use only batteries recommended by TOSHIBA as replacements E Do not remove the battery pack while the computer is in Standby mode Data is stored in RAM so if the computer loses power it will be lost When the computer is powered off in Standby mode and the AC adaptor is not connected the main battery pack and opti

User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents