SMS8 Alarm Control Panel
Contents
1. Plug pack 16 Volts AC 12 Volt DC Siren AS Tamper Switch Strobe Light N O O N gt D OG O C E O OD H O O O Be oc SMS8 Series 11 2 2 The Main Control Panel Mounting The control panel or main box should be located in a hidden position away from normal sight e g Linen press There should be a power point nearby to where the plug pack may be pushed This will supply power to the control panel The mounting position should be located close to a phone socket so that the telephone wire from the control panel can plug into the telephone socket This is required for the dialler to be operational to send SMS messages and back to base via the PSTN Public Switched Telephone Network Itis also helpful when the panel is located in a central position to make the wires to each detector shorter lengths This also gives added protection and security GSM MODEL The GSM model should be mounted in a high position so that the antenna can transmit and receive the best possible signal The minimum requirement for mounting this model is 1 2m above ground level Higher is better vy Wiring 2 2 1 Power Please see section Turning on the System 2 2 2 Back up battery Please see section Turning on the System RhinoCo Technology 2002 12 SMS8 Series 2 3 The Keypad EJ Description The2. Press Press enter to save the new Enter number for Phone 1 6 Press e Enter RhinoCo Technology O 2002 SMS8 Series 65 4 3 6 3 Phone Number 2 7 m Enter the new phone number for j daisi Phone 2 S Press LT repeatedly to exit and disregard any changes This number is sent on SMS messages and used as identification if multiple panels are reporting back to one number If using back to base monitoring this number must be allocated by the monitoring company or control room Panic Press w 0 Move the cursor back one space Medical Press k t0 move the cursor forward one space O H Ar Press to delete the digit on the cursor Press Press enter to save the new Enter number for Phone 2 8 Press Enter RhinoCo Technology O 2002 66 SMS8 Series 4 3 6 4 SMS Network Phone Number d SMS_NetPh i e m Enter the new phone number for the Cancel SMS Network Press repeatedly to exit and disregard any changes CAUTION You should leave this number 125 107 The 018018767 number is being phased out Do not change this to any other number if the panel is being used in Australia Panic Press w IO Move the cursor back one space a Medical Press ke t0 move the cursor forward one space HAm Press to delete the digit on the cursor Press Press enter to save the new Enter number for the SMS Network 10 Ca Rhin
3. EE 4 1 General eer Ee 4 1 1 Quick Programming Guide icsesnsionscuesracneteaeveneureidesennepahacnaausioteretemmrecnaionses 9 T 4 2 End User e ee E 4 2 1 How To Enter User EE j RhinoCo Technology 2002 A SMS8 Series 4 2 1 1 Changing Veras DD 4 2 1 2 Change the SMS Phone Number seekrreeggureerreekererer kee keggeeetzeec 40 4 3 Installer et L 4 3 1 How To Enter Installer Mode cccssscssssrsscsssscsssnrsesssscscesseccsessnes I 4 3 2 Option 1 Installer Code and User Code Programming 43 4 3 2 1 Changing The Master Code uaamesmrsanssrnmdednnnnnmnen 13 4 3 2 2 Changing User Codes 44 2 Option 2 ZONES eee AD 3 3 1 Zone Type 45 3 3 2 E 3 EE 33 A RE 3 3 5 Siren Type Ea ZOOM ISOCAM E 3 3 7 Ee 3 3 8 Zone Response Time aar 3 3 9 Pulse eee A POLEN fe JU 4 3 4 Option 3 Emergency Keys essens dnne DL TT NL 4 34 2 Medical Si CM eee 434 3 Fire EE NEEE EEE a EEE EEEE SNORRE ESAE SERS 4 3 5 Option 4 Timers Control ssssessesssessesesssersseseessresseseessersssreessreesseseesee TEN ED ae ATT DTS DN 33 0 AC Timer Deer 3 3 x Battery ONS 3 5 8 Battery Period DEE EN ENEE 33 10 E SLR Terre 3 3 12 Dial Enabl eee 3 3 A3 ee EE 4 Ph l E Bookmark fi 3 5 14 Phone Remote GSM only Error Bookmark not defined PA OT ee 4 3 6 Option 5 Devra OJ M Account ND E OO 3 6 2 Phone Number E 3 0 3 Phone Number eee OO 3 6 4 SMS Network P
4. SMS8 Alarm Control Panel 8 Zone Alarm Control Panel with LCD Keypad Inbuilt Dialler for Back to Base Monitoring and SMS Messaging LG Easy Operation G Daller GJ SMS Messaging A N517 Model Available Code Description SMS8 Alarm with PSTN dialler standard model Document SMS8v2 2 doc Release 31 July 2009 TM Ma pw www watchguardalarms com au 2 SMS8 Series This page intentionally blank RhinoCo Technology 2002 SMS8 Series 3 Contents CERES once um autos EE ER Pet 916 10 6 ER EE te etre Caner ort tr EE 6 IE PSCC e Ee AE ege Te WD What Eeer deer RE TT EG EEE sans O EEO DNL 2 2 The M in C ntrol Panel EEE EE IL Te Pla 24 Te Outside Sire NK 2 5 WEEN E LA SG Rn 21 The Backup Bauer eege SE EA E ie A 3 0 How To Arm The System Ee 3 1 How To Quick Arm The System geet edeteteten deeg eege 3 2 How To Home Arm the System GGIAY nn 24 3 3 How To Egeter eeh TONN 3 4 0 How to Arm via Mobile Phone GSM model only 20 3 4 1 How to Disarm via Mobile Phone GSM model only 20 3 4 2 How to Check Status via Mobile Phone GSM model only 27 3 4 3 Phone Messages E vr TESE 3 6 H w To Entet Test M de seres EE KE 3 5 2 Siren amp Strobe Teie DN 39A Battery TES EE ER o 3 7 How To Enter Service Mode Lupsuranuukninsteeismnimktaniits gd 3 8 Resetting EN EE sD VENT
5. with Phone 1 is unsuccessful Phone 2 will be dialed SMS8 Version only Press Press enter to save the new Enter setting and move to the next feature Press 16 Enter Press Enter to move forward to the next feature RhinoCo Technology O 2002 70 SMS8 Series 4 3 6 8 Dialer Test Reports eg Press w to change the dialer test setting A detailed list of the settings is shown below Yes This will enable automatic dialer test reports Not This will disable automatic dialer test reports Press Press enter to save the new setting Enter and move to the next Event Reports menu 18 Press Press Enter Cancel to go to the Repeatedly to go back to the ready next Event screen Report menu RhinoCo Technology 2002 SMS8 Series 4 3 7 Option 6 Event Reports 71 1 Once you enter option 6 from installers mode or from the previous menu the display will show the following eier Menu Press eier N Enter Y Menu to go Cas to the installer options 2 Press Enter Press Enter to select the Report menu 3 4 3 7 1 Zone Reports Zone Fn Press Fn N Enter Y Menu to to the next Events menu Press Menu to skip to the next Events menu Press Enter Press Enter to select the Report menu RhinoCo Technology O 2002 72 SMS8 Series 4 3 7 1 1 Alarm Reporti
6. 4 Defaulting The System 1 Remove all power from the SMS8 panel 2 Place a short on the default pads on the main board 7 ZS dt e Ee 5 ai ee Os 3 Power up the panel by either connecting the AC plugpack or the backup battery 4 Remove the short on the two default pads 5 The panel is now defaulted and the shaded values in the section Installers Programming now apply RhinoCo Technology O 2002 SMS8 Series 81 5 Warranty 5 1 Warning Limitations amp Warranty While this system is an advanced security system it does not offer guaranteed protection against burglary or any other emergency Any alarm system whether commercial or residential is subject to compromise or failure to warn for a variety of reasons For example e Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm or disconnect an alarm warning device e Intrusion detectors e g microwave detectors and many other sensing devices will not work without power Battery operated devices will not work without batteries with dead batteries or if the batteries are not put in properly Devices powered solely by AC will not work if their AC power supply is cut off for any reason however briefly e Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver Even if the signal path has been recently checked during a weekly test block
7. 4 0 How to Arm via Mobile Phone GSM model onl To Arm the alarm through Phone Operations be sure Phone Remote is enabled in programming option 4 Send a text message as shown below to the mobile number assigned to the alarm system When the system receives the message it will Arm 1234A NOTE Replace 1234 with your assigned Master Code To receive a confirmation that your system is armed ensure that Closing reports are programmed in option 6 The confirmation message will be sent to the SMS receiver number programmed into the system If programmed you will receive a close message to confirm the system is armed A closing message will look similar to what is shown below by user 1 End Account No 9991 Close RhinoCo Technology 2002 26 SMS8 Series 3 4 1 How to Disarm via Mobile Phone GSM model onl To Disarm the alarm through Phone Operations be sure Phone Remote is enabled in programming option 4 Send a text message as shown below to the mobile number assigned to the alarm system When the system receives the message it will Disarm 1234D NOTE Replace 1234 with your assigned Master Code To receive a confirmation that your system is disarmed ensure that Opening reports are programmed in option 6 The confirmation message will be sent to the SMS receiver number programmed into the system If programmed you will receive a open message to confirm the system is disarmed A open
8. E No Press mm to change the setting A detailed list of the settings is shown below No will enable the zone to activate in home mode Yes will disable the zone in home mode Press Press enter to save the Enter setting and move forward to the next feature 1 5 Press 8 ER Press Enter to move forward to the next feature RhinoCo Technology O 2002 SMS8 Series 49 1 6 Response 1 D 500 Msec 4 3 3 8 Zone Response Time Menu Press kl to change the setting A detailed list of the settings is shown below 20 Msec The zone must be open for 20 milli seconds before it will be trigger and register as an alarm 250 Msec The zone must be open for 250 milli seconds before it will be trigger and register as an alarm 500 Msec The zone must be open for 500 milli seconds before it will be trigger and register as an alarm This setting suits most sensors Press Press enter to save the Enter setting and move forward to the next feature 17 Press Enter Press Enter to move forward to the next feature 1 Q Double Hit 1 e No 4 3 3 9 Pulse Count Menu Press IO change the setting A detailed list of the settings is shown below No Will enable the zone to trigger the alarm after the zone opens once Yes Will only allow an alarm trigger after it has opened the zone twice Press Press enter to save the Enter s
9. RJ11 jack from the panel as this may prevent the premise telephones from operating If the telephone system returns to normal operation after the removal of the panel from the line the control panel has a problem and should be returned for repair All faulty equipment whether under warranty or out must be returned to RhinoCo Pty Ltd or it s authorized service agents for repairs RhinoCo Technology 2002 36 SMS8 Series 4 Programming 4 1 General Programming mene Cancel d y x Throughout programming 3 common keys are used MENU ENTER and CANCEL keys are used to navigate through the various programmable options Their functions are outlined below This key is used for cycling through either a menu or options Pressing this button will display the next menu or next option This is for selecting a menu option or saving a selection or setting This key is for moving back up a step and will not save any changes to the current selection If held down for approximately 3 seconds it will exit programming mode Where a cursor is displayed for example when programming phone numbers this key will move the cursor back one position Where a cursor is displayed for example when programming phone numbers this key will move the cursor forward one position Where a cursor is displayed for example when programming phone numbers this key will delete the number above the cursor Rh
10. RhinoCo Technology O 2002 56 SMS8 Series Dem Dial Offset SCH ee f Menu Press t0 change the Dialer Offset setting A detailed list of the settings is shown below The times are in hours This feature allows the user to select what time of the day the panel will perform a dialer test The dial test will be performed after the chosen amount of hours once you exit programming mode eg If you choose 2h then the dialer test will be performed 2 hours after you exit programming mode 0 1h 2h 22h 23h increments up by 1 hour wll Press Press enter to save the new Enter setting and move to the next feature Press Press Enter to move forward Enter to the next feature 4 3 5 5 Dial Period Dial Period al Menu Press rn to change the Dial Period setting A detailed list of the settings is shown below N gt 3 This feature allows the user to select what the time between test reports 24h 24 hours between test reports 7d 7 days between test reports 30d 30 days between test reports Press Press enter to save the new Enter setting and move to the next feature Press Enter Press Enter to move forward to the next feature RhinoCo Technology O 2002 SMS8 Series 57 Q Ac Timer Delay e 15m 4 3 5 6 AC Timer Delay Menu Press vd to change the AC Timer Delay setting A detailed li
11. enter to save the new Enter setting and move to the next feature 22 Press Enter Press Enter to move forward to the next feature I 4 3 5 13 RF Remote No Press vd to change the RF Remote setting A detailed list of the settings is shown below RF version only This feature when enabled allows the SMS8 RX to remotely arm disarm the system No This will not allow the SMS8RX receiver to work with the SMS8 alarm panel Yes This will enable the SMS8RX receiver to work with the SMS8 alarm panel Press Press enter to save the new Enter setting and move to the next feature RhinoCo Technology 2002 62 SMS8 Series 4 3 5 15 Open Override E No Press to change the Open Override setting A detailed list of the settings is shown below Only applicable when using the CID or GSM CID formats When enabled this will allow the panel to send an open report only after an alarm has occurred you must also disable open and close reports No Disables open override Yes Enables open override Press Press enter to save the new Enter setting and move to the next dialer menu 27 Press Press Enter Cancel to go to the Repeatedly to go back to the next dialer ready screen menu RhinoCo Technology 2002 SMS8 Series 63 4 3 6 Option 5 Dialer Once you enter option 5 from installers mode o
12. general operation features 3 Tamper Switch A tamper switch for the main control panel is supplied along with a bracket to which it mounts When attached 1 A to the sys 4 Accessories End of Line Resistors EOLR are supplied with the a ae system to provide a high degree of security to the wiring 1 z m a 3 of the system These are used on the wiring of each zone Pi 5 Phone Lead A telephone lead is supplied to connect the security 1 d system to an existing telephone line socket RhinoCo Technology 2002 SMS8 Series 2 Installation 2 1 Overview general overview of the components that may be installed with the alarm system is shown below in the diagram This also includes an example only of the wires that must be routed through the roof of the building C1 Control Panel K1 Keypad nt NI Screamer OG STN s Smoke Sensor 2 e Main Siren Box A list of the type of wires that should be run is shown below Minimum requirement Keypad 4 Core cable Screamer Figure 8 cable 2 cores Passive Infrared sensor 4 core security cable Reed Switch Figure 8 cable 2 cores Smoke Detector 4 core security cable RhinoCo Technology 2002 P1 Passive Infrared Sensor P2 Passive Infrared Sensor 2 RI Reed Switch 1 R2 Reed Switch 2 SMS8 Series 10 2 1 1 Wiring Summar Operation LED To PSTN Phone Socket
13. go back to the previous user code This will not save any changes to the current user code Cancel 2 S Press Lu repeatedly to exit user programming Press Menu ene to go back to the Installer PIN menu OR Press Cancel Repeatedly to go back to the ready screen RhinoCo Technology 2002 SMS8 Series 45 4 3 3 Option 2 Zones Once you enter option 2 from installer s mode the display will show the following EE Press Press Menu to select the next li bas zone This will cycle through Display for GSM version Set Zones 1 Menu N Enter Y the zones Zi Press Press Enter to select the zone shown on the display Zone Type 1 Delay 4 3 3 1 Zone Type Menu Press IO change the setting A detailed list of the settings is shown below Disable will de activate the zone Select this when the zone is not being used Delay will give the user time to disarm the system before generating an alarm if this particular zone is triggered on entry Interior will not generate an alarm on entry if a delay zone is triggered first It will generate an alarm if a delay zone has not been triggered first Instant will generate an alarm instantly once armed 24h Zone will generate an alarm instantly whether the system is armed or disarmed Default settings Zone Delay Zone 2 3 amp 4 Interior Zones 5 6 amp 7 Instant
14. menu This will not save any changes to the SMS phone number Cancel Press LYE repeatedly to go back and exit user programming or until the Ready screen is displayed Press Menu to go back to the select user menu OR Press Cancel Repeatedly to go back to the ready screen RhinoCo Technology 2002 SMS8 Series 41 4 3 Installer Programming This area is generally used when the system is first installed into the premises or when changing system components adding removing detectors and sensors after defaulting the system 4 3 1 How To Enter Installer Mode Ensure the keypad is displaying Ready 3 Press Press the Menu Key Menu a X 3 three times from the ready screen 3 game The display will show Menuen Enter Y the following Brow 4 Press Press the Enter key to Enter select program mode 5 See The display will show Wat EntoraY the following Gren 6 Press Press the Menu key to H Me pa select Install mode An example of a service Install Mode amo Menu N Enter Y message is shown here RhinoCo Technology 2002 42 SMS8 Series Press the Enter key to select Install mode The display will show amo Code foll i Enter the ollow1ng rowe Enter the Installers code Default is 012345 The display will show the following 12 Press DT for installer code and
15. save the new Enter setting and move to the next feature Press Enter to move forward to the next feature Press 6 Enter 4 3 7 2 3 Panic Reporting 7 Yes Press to change the Panic Reporting setting A detailed list of the settings is shown below ze This refers to the key if held for 2 seconds on your keypad Yes Will enable the dialer when a panic event occurs No Will disable the dialer when a panic event occurs Press Press enter to save the new Enter setting and move to the next feature Press Enter to move forward to the next feature RhinoCo Technology 2002 SMS8 Series 77 4 3 7 2 4 Medical Reporting Menu 9 e Press to change the Medical Reporting setting A detailed list of the settings is shown below This refers to the Le key if held for 2 seconds on your keypad Yes Will enable the dialer when a medical event occurs No Will disable the dialer when a medical event occurs Press Press enter to save the new Enter Enter setting and move to the next feature Press Enter Press Enter to move forward to the next feature 4 3 7 2 5 Fire Reporting Menu 1 1 5 Press vd to change the Fire Reporting setting A detailed list of the settings is shown below 0 Fi This refers to the ups key if held for 2 seconds on your keypad Yes Will enable the d
16. the keypad is displaying Ready GA Ready 3 Dress Press the Menu Key three e Menu X 3 times from the ready screen The display will show the MenucN Enter V following 4 Press Press the Enter key to e Enter select program mode The display will show the hoe ey following 6 Press Press the Enter key to LU Enter select User mode An example of a service eer Put MasterlD ae message is shown here g Cal ai la Enter the valid master code default is 1234 RhinoCo Technology O 2002 SMS8 Series 39 4 2 1 1 Changing User Codes 9 PRS m Press This will allow you to change user codes I to Menu N Enter Y Enter 16 User I is the Master Code Change User 1 Code 1234 Enter the new 4 digit code for the displayed user Enter Press to save the new user code and to select the next user Cancel Press LL to go back to the previous user code This will not save any changes to the current user code Press repeatedly to exit user programming until the Ready screen is displayed RhinoCo Technology 2002 A0 SMS8 Series 4 2 1 2 Change the SMS Phone Number 1 1 Program SMS Press This will allow you to change the SMS phone e Menu N Enter Y Enter number Enter Ph No 0416036583 Enter the new mobile phone number Enter Press IS to save the new phone number Cancel Press Kn to go back to the Program SMS
17. user code programming OR Press J for zone programming OR Press ior emergency key programming OR Press GEE for timers control programming OR Press S for dialer programming OR Press for event report programming RhinoCo Technology O 2002 SMS8 Series 43 4 3 2 Option 1 Installer Code and User Code Programmin This menu will enable you to change the installer code master code and any user code The panel can store up to 16 user codes Once you enter option 1 from installers mode the display will show the following Ee PIN Enter the new 6 digit installer code gesent e e Press LZ repeatedly to exit and disregard any changes Press Press enter to save the new Enter installer code I J Press 2 e Menu ee 4 3 2 1 Changing The Master Code Master PIN 3 CODE 1234 m Enter the new 4 digit Master a Code Press LZ repeatedly to exit and disregard any changes Press Enter Press enter to save the new installer code l d re dem RhinoCo Technology 2002 44 SMS8 Series 4 3 2 2 Changing User Codes 5 Select a user 2 16 S Press LEE repeatedly to exit and disregard any changes User No i e GEES 2 The display will show the following example only Enter the new 4 digit code for the displayed user Enter Press se to save the new user code and to select the next user Cancel 1 Press Lu to
18. 3 7 2 4 Medical R a af Te TR SPOT E 77 4 3 7 2 6 Duress ROR Rs eege dE 78 4 3 7 2 7 AC Loss E 78 4 3 7 2 8 Low Backup Battery Reporting ssrorornnrrvnrennnnvennrrvernnrnnsennrnvernnn 79 4 3 7 2 9 Receiver Supervision Reporting seseseesssrssesrssseresssresseresssee 79 4 4 Defaulting The System E 80 5 Warranty RE ENE TE 81 5 1 Warning Limitations amp Warranty sieegbenrebegeugdetegagdetegegeleree eben ER fane 81 RhinoCo Technology 2002 6 SMS8 Series 1 Introduction Thank you and congratulations on the purchase of the SMS38 security control panel With all the latest technology and ideas the RhinoCo ranges of control panels are unique in simplicity in programming and in use The SMS8 offers eight zones a siren and a strobe output auxiliary and switched power terminals for peripherals and depending on the model purchased a dialler or dialer and a GSM backup unit All programming is via an alphanumeric LCD keypad and all programming options are menu driven The end user options are well laid out and a breeze to operate This instruction manual has been designed for ease of reading and also as a quick reference for any questions you may have about the product Proudly Designed in Australia Warning The manufacturer and or its agents take no responsibility for any damage injury or financial loss to any property equipment or persons resulting from correct or incorrect use of the RhinoCo range
19. Keypad should be installed at the entrance of the premises to allow for easy arming and disarming when leaving entering the door The keypad is where you are able to control all functions of the alarm system and perform any necessary programming E Mounting Use four x 6 Gauge counter sunk screws not supplied to mount the back plate of the keypad to the wall The hole in the centre of this back plate is where the wire will go through then into the wall and back to the main control panel MAKE SURE YOU HAVE THE KEYPAD WIRES FROM THE CONTROL PANEL HANGING OUT FROM THE WALL AND THROUGH THE HOLE IN THE CENTRE OF THE KEYPAD BACK PLATE Keypad Back Plate t V n How to clip the keypad onto the back plate RhinoCo Technology 2002 SMS8 Series vy Wiring x a x COMM BUS BUS 13 Using 4 core cable preferably Connect the terminals on the keypad to the respective terminal on the main control panel NOTE A maximum of four keypads can be connected If more than one keypad is connected the other keypads have to be addressed Use JP1 amp JP2 for the addressing of the keypad Vy Keypad Assignment Lerend Jumper OFF Jumper ON If only one keypad is being installed the jumpers do not need to be moved If more than one keypad is being installed then each keypad must be assigned individually and no additional k
20. RRANTY Cornick Pty Ltd ABN 74 001 621 610 Seller warrants its products to be in conformance with its own plans and specifications and to be free from defects in materials and workmanship under normal use and service for twelve months from the date of original purchase Sellers obligation shall be limited to repairing or replacing at its option free of charge for materials or labor any part which is proved not in compliance with Sellers specifications or proves defective in materials or workmanship under normal use and service Seller shall have no obligation under this Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than Seller For warranty service return transportation prepaid to 9 Hannabus Place McGraths Hill NSW 2756 Seller has no obligation to attend the buyer s location to retrieve the goods or make repairs onsite There are no warranties expressed or implied of merchant ability or fitness for a particular purpose or otherwise which extend beyond the description on the face hereof In no case shall seller be liable to anyone for any consequential or incidental damages for breach of this or any other warranty express or implied or upon any other basis of liability whatsoever even the loss or damage is caused by its own negligence or fault Seller does not represent that the products it sells may not be compromised or circumvented that the products will prevent any perso
21. Zone 8 24h Zone Press Press enter to save the new Enter setting and move to the next feature 4 Press Enter Press Enter to move forward to the next feature I RhinoCo Technology O 2002 46 SMS8 Series Chime 1 No 4 3 3 2 Chime Menu Press to change the setting A detailed list of the settings is shown below No will disable chime Yes will sound the keypad buzzer when a zone is triggered when the system is in the disarmed state Press Press enter to save the Enter setting and move forward to the next feature Press 6 Tr Press Enter to move forward to the next feature 4 3 3 3 RF Zone 7 R ges 1 Wee Press kl to change the setting A detailed list of the settings is shown below No will disable the zone from being used as a wireless zone Yes For use with the RhinoCo Wireless receiver and sensors Product Code SMS8RX PIRW amp WREED etc NOTE This mode should be set to disabled if none of these devices are being used Press Press enter to save the Enter setting and move forward to the next feature Press Enter to move forward to the next feature RhinoCo Technology 2002 SMS8 Series 47 4 3 3 4 Zone Restore S On Disarm Press IO change the setting A detailed list of the settings is shown below On Disarm Once the time out period has finished that zo
22. a message every 24 hours if the battery is flat 7d Sends a message every 7 days if the battery is flat 30d Sends a message every 30 days if the battery is flat Press Press enter to save the new Enter setting and move to the next feature Press Enter to move forward to the next feature 14 Ce RhinoCo Technology 2002 SMS8 Series 59 4 3 5 9 Line Delay z Disable Press rn to change the Line Delay setting A detailed list of the settings is shown below This is the maximum time allowed for the Telephone line to be disconnected from the panel or for the wrong line voltage being detected before the LINE DELAY message is generated and sent via SMS message to the programmed number Disabl Does not send any message for telephone line faults 15min Sends a message if the phone line is not working for more than 15 minutes 30min Sends a message if the phone line is not working for more than 30 minutes 45min Sends a message if the phone line is not working for more than 45 minutes Press Press enter to save the new Enter setting and move to the next feature Press 16 Enter Press Enter to move forward to the next feature RhinoCo Technology O 2002 60 SMS8 Series 4 3 5 10 Bell Reverse Press kd to change the Bell Reverse setting A detailed list of the settings is shown below Bell Reverse will enable the BELL
23. ady screen RhinoCo Technology 2002 34 SMS8 Series 3 7 How To Enter Service Mode If the keypad is showing a SERVICE message enter the SERVICE MESSAGE menu by following these steps 1 Press Press the Menu Key four Menu X 4 times from the ready screen 2 gene The display will show the Service M Menu N Enter Y following Brown 3 Press Press the Enter key to weg select the service message menu An example of a service geg TampAlarm h h Zone 3 Lounge message IS Shown nere ad Brown S Dress Press the Enter key to e Enter cycle through any additional service messages 6 Press Press the cancel button S Cancel repeatedly to exit back to Repeatedly the ready screen RhinoCo Technology 2002 SMS8 Series 35 3 8 Resetting The Alarm If a violation of a zone has occurred while the system was armed this will be shown on the display follow these steps to clear the memory 1 Press Press the Menu Key five e M Gr X 5 times from the ready screen 2 genee The display will show the Menu N Enter Y following Brower 3 Press Press the Enter key The Enter memory will be cleared and the display will return to the ready screen This clears the SERVICE message as well 3 9 Telephone Line Faults In the case of line problems with the telephone system disconnect the RhinoCo panel from the line do not disconnect from the
24. age can occur if a metal object is moved into the path e Microwave Detectors can only detect intrusion within the designed ranges as set out in their installation manual e Alarm warning devices such as sirens bells or horns may not alert people or wake up sleepers who are located on the other side of closed or partly open doors Even persons who are awake may not hear the warning if the alarm is muffled by noise from a stereo radio air conditioner or other appliances or by passing traffic Finally alarm warning devices however loud may not warn hearing impaired people or waken deep sleepers e This equipment like other electrical devices is subject to component failure Even though this equipment is designed to last as long as 10 years the electronic components could fail at any time e The most common cause of an alarm system not functioning when an intrusion occurs is inadequate maintenance This alarm system should be tested weekly to make sure all devices are working properly e Installing an alarm system may make one eligible for lower insurance rates but an alarm system is not a substitute for insurance Owners should continue to act prudently in protecting themselves and continue to insure their property We continue to develop new and improved protection devices Users of alarm systems owe it to themselves and their loved ones to learn about these developments RhinoCo Technology 2002 82 SMS8 Series LIMITED WA
25. amer types available include Flush mount screamer Top hat screamer Py Mounting Screamer s are generally mounted on the ceiling It can be located almost anywhere you like It is advised that you place it in a position that is central where the sound travels evenly through the house Since its main purpose is to make the sound unbearable to any would be intruder you may choose the most appropriate position to best suit the building to which it is installed Example mounting a top hat screamer 1 Drill a hole 15mm diameter into the ceiling where you want to mount the screamer This where the wire from the screamer will pass through Pick a position where there is no stud framework above the ceiling preferably in a central position such as a corridor or hallway 2 Feed the wire coming from the screamer up through the 15mm hole into the ceiling where it will join to the wire going to the control panel 3 Push the screamer on to the ceiling aligning the hole with the wire coming out of the screamer 4 Place the self tapping screws into the mounting holes on the screamer RhinoCo Technology 2002 SMS8 Series 19 then screw them into the ceiling vy Wiring ER tnat A ei e E re gt ag Control Panel The screamer is wired to the BELL and COMM terminals on the control panel in parallel with the DC Siren RhinoCo Technology O 2002 20 SMS8 Se
26. chnology 2002 SMS8 Series 79 4 3 7 2 8 Low Backup Battery Reporting 17 Sys batt Yes Menu Press vd to change the Low Backup Battery Reporting setting A detailed list of the settings is shown below Will enable the dialer to send low battery notification messages when the back up battery is low Yes Will enable the dialer when a Low Backup Battery has been detected No Will disable the dialer when a Low Backup Battery has been detected Press Press enter to save the new Enter setting and move to the next feature 18 Press Enter Press Enter to move forward to the next feature 4 3 7 2 9 Receiver Supervision de 19 f T Menu m to change the Receiver Supervision Reporting setting A detailed list of the settings is shown below Yes Will enable the dialer when the panel detects that the SMS8RX receiver is not communicating with the panel No Will disable the dialer when the panel detects that the SMS8RX receiver is not communicating with the panel Press Press enter to save the new Enter setting and go back to the installers option menu 20 Press to go back to the installers menu Press Enter to go back to the installers option menu or Cancel press LE repeatedly to exit back to the ready screen 21 Installers option menu RhinoCo Technology O 2002 80 SMS8 Series 4
27. e Steady The display will show the following Press Menu to select one of the options E Press a to keep the current setting or press c repeatedly to exit below back to the previous menu Disable Disables panic from triggering the siren Steady Enables the siren to sound steady when panic is triggered Pulsing Enables the siren to turn on then back off every second when panic is triggered is triggered Just Keypad Enables only the keypad to buzz when panic Press Enter Press Enter to save your choice and move to the next menu Press Enter to move forward to the next feature RhinoCo Technology O 2002 52 SMS8 Series 4 3 4 2 Medical Siren 5 pale Press D Menu N Enter Y Press Enter to select the a SE ater panic option The display will show the following Press Enter Press LS to keep the Menu 8 current setting or press to select one c e of the options L repeatedly to exit below back to the previous menu Disable Disables panic from triggering the siren Steady Enables the siren to sound steady when panic is triggered Pulsing Enables the siren to turn on then back off every second when panic is triggered Just Keypad Enables only the keypad to buzz when panic is triggered Press Press Enter to save your Enter choice and move to the next menu Press 6 Menu Press Enter t
28. e display will cycle GA Ready Bypass through each isolated zone NG for 6 seconds before moving to the next Groven RhinoCo Technology O 2002 SMS8 Series 31 3 6 How To Enter Test Mode The TEST MENU will allow the installer to perform a WALK TEST of the Zones a SIREN amp STROBE TEST DIALLER TEST and a BATTERY TEST 1 Press Press the Menu Key twice e M enu X D from the ready screen The display will show the no 2 Deeg following P Brow 3 Press Press the Enter key to e Enter select the Test Menu 3 5 1 Walk Test 4 Zone Test Press Each time a zone is triggered the zone number e Menu N Enter Y m Enter willbe displayed for one second and the keypad will beep Walk Test R Zone 4 Lounge Zone 4 triggered Then each zone triggered will be displayed for 6 seconds each If you press the a button it will scroll forward displaying each zone that has been triggered up to the most recent zone triggered Cancel Press Lu to exit this mode Press Menu RhinoCo Technology 2002 32 SMS8 Series Di i 6 Siren Stb Menu N Enter Y Press Menu m 3 5 2 Siren amp Strobe Test Press This will allow the installer to test the SIREN Enter and the STROBE The siren and strobe will activate for 3 seconds If the siren and strobe are not wired you will not be able to perform this test Press repea
29. e exit back to the ready screen same set of features above for the next zone up to zone 8 number on top right side of the display 15 Press Press Enter to move forward Enter to the next Events menu to move forward to the Cancel Press L repeatedly to Events Menu exit back to the ready screen RhinoCo Technology O 2002 SMS8 Series 75 1 4 3 7 2 Events Menu e Events Press Cancel 1 Menu N Enter Y Mens Press LIE repeatedly to in exit back to the ready screen to go back to the Zone Report menu Press 2 Enter Press Enter to select the Report menu 4 3 7 2 1 Open Reporting 3 ar i i i i Press to change the Open Reporting setting A detailed list of the settings is shown below Yes Will enable the dialer when an open or disarming event occurs No Will disable the dialer when an open or disarming event occurs Press Press enter to save the new Enter setting and move to the next feature Press Enter to move forward to the next feature 4 Press Enter RhinoCo Technology O 2002 76 SMS8 Series 4 3 7 2 2 Close Reporting i ZS Press nm to change the Close Reporting setting A detailed list of the settings is shown below Yes Will enable the dialer when an close or arming event occurs No Will disable the dialer when an open or arming event occurs Press Press enter to
30. e intentionally blank RhinoCo Technology 2002
31. etting and move forward to the next feature 19 Press Enter Press Enter to move forward to the next feature RhinoCo Technology O 2002 50 SMS8 Series 4 3 3 10 Zone Name 0 Zone Name 1 f e None Menu Press kd to change the setting A detailed list of the settings is shown below The name that you choose for the particular zone will be shown on the keypad and on SMS messages None M Bedroom Reception Show Room FrontDoor Bedroom 2 Office 1 Hallway BackDoor Bedroom 3 Office 2 Panic Kitchen Fire Office 3 Tamper Lounge Garage Workshop Dining Basement StoreRoom Press Press enter to save the Enter setting and move to the first feature on the next zone Press Enter to go back to first feature of the next zone OR Press Cancel Repeatedly to go back to the ready screen RhinoCo Technology 2002 SMS8 Series 4 3 4 Option 3 Emergency Keys 51 Once you enter option 3 from installers mode the display will show the following dt Press dt N Enter Y Press Menu to move to the Timer amp Control options or Cancel press LTE repeatedly to exit back to the ready screen A 3 Press Enter Press Enter to select the Emergency options 4 3 4 1 Panic Siren Panic 3 Menu N Enter Y a Press 1 Enter Press Enter to select the panic option Siren Typ
32. eypad may set up the same Way WARNING DO NOT PLACE A JUMPER IN THE JP3 Jumper 3 POSITION JP1 JP2 JP3 Keypad 1 i Jumper 1 ON only JP1 JP2 JP3 Keypad 2 H Jumper 2 ON only JP1 JP2 JP3 Keypad 3 a il Jumpers I amp 2 ON only JP1 JP2 JP3 Keypad 4 No Jumpers installed default RhinoCo Technology 2002 14 SMS8 Series KPWR BUS BUS RhinoCo Technology 2002 SMS8 Series 2 4 The Outside Siren Description The outside siren performs the following important functions 1 Provides an alarm sound when the system is triggered lets anyone nearby know that an alarm has occurred 2 Provides visual deterrent to any would be thieves Provides visual alert when the alarm has been triggered Go 4 A tamper switch protects it so that no thief is able to remove it without the alarm being triggered Py Mounting Mount the Outside Siren and Strobe at the front or front side of the building The mounting position should be under an eave or out of direct contact with rain or other water sources The position should allow line of sight viewing from both the street for visual deterrent and from your main point of entry for visual confirmation of arming disarming optional Example Assemble the Siren Box esu Insert the Siren Tamper Switch and Strobe into the Siren Box RhinoCo Technol
33. hone Number OG 3 6 5 Receiver I Format Type D D D D ree ee eee eee eee eee eee eee eee eee eee eee eee ee ee eee rer eee rere rere rec ere rere rere errr l RARRARARAA D D D D D D D D Ch Ch Ch Ch Li LN Lin Lin LN Lin LD LN LD WR WM ka bah Ei CH M Di zl zl Ch Ch Ans BWW D D D D AN I RhinoCo Technology O 2002 SMS8 Series 5 4 3 6 6 Receiver 2 Format ENEE ege 68 4 3 6 7 FNS 69 25608 Dialer Test Reports steiere dE 70 4 3 7 Option 6 Event Repotts ssessesesesesseeessseesseressseessreesssresseresssresseresssressees 71 6 iON REPOL EE 71 4 3 7 1 1 Alarm Reporting EE 72 EE RE Reporting sericea sceese sas persenan idesi eini esssnia s irasra nErinn 72 4 3 7 1 3 Isolation Reporting asc esis eege 73 4 3 7 1 4 RF Battery Eu E 73 ee RF Loss REDON UND so tanacuensnvuauenssheadenvuunsiedaranuersevanuctdcaadsrercenannd 74 4 3 T2 NU 75 eer Open EE riede Aire is EAE 75 4 3 7 2 2 E e EE 76 EE Panie E 76 4
34. ialer when a Fire event occurs No Will disable the dialer when a Fire event occurs Press Press enter to save the new Enter Enter setting and move to the next feature Press 6 7 Enter Press Enter to move forward to the next feature RhinoCo Technology O 2002 78 SMS8 Series 4 3 7 2 6 Duress Reporting Menu 13 Press vd to change the Duress Reporting setting A detailed list of the settings is shown below A Duress is triggered by the User code 8 being entered Yes Will enable the dialer when a Duress event occurs No Will disable the dialer when a Duress event occurs Press Press enter to save the new Enter setting and move to the next feature 14 Ce Press Enter to move forward to the next feature 4 3 7 2 7 AC Loss Reporting 15 Sen Menu e Press to change the AC loss Reporting setting A detailed list of the settings is shown below AC OK will be sent as soon as the AC Power is reconnected to the system AC LOSS will be sent as soon as AC Power is removed from the system and the AC timer is up Yes Will enable the dialer when an AC loss event occurs No Will disable the dialer when an AC loss event occurs Press Press enter to save the new Enter setting and move to the next feature 16 e Press Enter to move forward to the next feature RhinoCo Te
35. ing and move to the next feature Press 10 Enter Press Enter to move forward to the next feature 4 3 7 1 4 RF Battery Reporting 1 1 RF batt 1 eg 2 No Press vd to change the RF Battery Reporting setting A detailed list of the settings is shown below An RF Battery event occurs when the battery on one of the wireless detectors has a low battery This is only compatible with the SMS8RX receiver Yes Will enable the dialer when a RF low battery event occurs No Will disable the dialer when a RF low battery event occurs Press Press enter to save the new Enter setting and move to the next feature Press 12 Enter Press Enter to move forward to the next feature RhinoCo Technology O 2002 74 SMS8 Series 4 3 7 1 5 RF Loss Reporting Menu 13 Press vd to change the RF Loss Reporting setting A detailed list of the settings is shown below An RF Loss event occurs when one or more of the Wireless sensors has been missing from the system for more than 24 hours This is only compatible with the SMS8RX receiver and compatible sensors Yes Will enable the dialer when a RF loss event occurs No Will disable the dialer when a RF loss event occurs Press Press enter to save the new Enter setting and move to the same 14 set of features for the next zone Press Cancel Enter Press LEE repeatedly to to move to th
36. ing message will look similar to what is shown below Account No 9991 Open by user 1 End RhinoCo Technology 2002 SMS8 Series 27 3 4 2 How to Check Status via Mobile Phone GSM model onl To Check the Status of the alarm through Phone Operations be sure Phone Remote is enabled in programming option 4 Send a text message as shown below to the mobile number assigned to the alarm system When the system receives the message it will report back to the SMS number programmed into the system 1234ST 1234ST nl NOTE Replace 1234 with your assigned Master Code The status report you will receive will look similar to what is shown below Sys Disarmed Isolated None Ac supply ON Sys batt is Ok End RhinoCo Technology O 2002 28 SMS8 Series 3 4 3 Phone Messages SMS Some examples of SMS messages that may be sent to you from the alarm system are as follows RETTET You will receive this message when your alarm has Alarm Back door been triggered by the back door End PEART You will receive this message when your alarm has Restr Back door restored the back door zone End PTT You will receive this message when your alarm has Panic On been triggered by the Panic button End Account No 9991 You will receive this message when your alarm has Panic Off disarmed after a Panic activation End ETATEN You will receive this message when your alarm has Ac lost lost mains powe
37. inoCo Technology 2002 SMS8 Series 4 1 1 Quick Programming Guide Programming End User Programming Installer Programming 37 User Codes SMS Phone Number Option 1 Option 2 Option 3 Option 4 Option 5 Option 6 Installer Zone Emerge Control Dial Rpt PIN code Programming Emergency Timers Menu Menu User Reports PIN codes Master Zone Type Panic Siren Entry delay Account Zone Rpt Events Code Number User Codes Zone Chime Medical Siren Exit delay Phone 1 Alarm Open RF Zone Fire Siren Siren Time Phone 2 Restore Close Zone Restore Dial Offset SMS_ NetPh Isolation Panic 125107 Siren Type Dial Period Rec1 Form RF Battery Medical Zone Isolation AC timer Rec2 Form RF Lost Fire delay Home Mode Battery Routine Duress offset Rec Zone Response Battery Dial Test AC Lost Period Pulse Count Line Delay Sys batt Zone Name Bell Reverse Remote RF Tamper lh Dial Enable RF Remote Open Override RhinoCo Technology 2002 38 SMS8 Series 4 2 End User Programming This area is for the changing of the user PIN numbers and the SMS phone number that the system will send messages to in the event of the alarm being activated 4 2 1 How To Enter User Mode Ensure
38. nal injury or property loss by burglary robbery fire or otherwise or that the ao will in all cases provide adequate warning or E Customer understands that a properly installed and maintained alarm system may only reduce the risk of a burglary robbery or fire without warning but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result Consequently seller shall have no liability for any personal injury property damage or other loss based on a claim the product failed to give any warning However if seller is held liable whether directly or indirectly for any loss or damage arising under this limited warranty or otherwise regard less of cause or origin seller s maximum liability shall not in any case exceed the purchase price of the product which shall be the complete and exclusive remedy against seller This warranty replaces any previous warranties and is the only warranty made by Seller on this product No increase or alteration written or verbal of the obligations of this Limited Warranty is authorised NOTE In addition to the warranty conditions warranty will not be given where a product has been immersed in water under any circumstances or where damage has been caused by hosing the unit without all due care taken by the owner to protect the unit by covering with some sort of plastic sheeting RhinoCo Technology 2002 SMS8 Series 83 This pag
39. ne cannot be re triggered until the alarm is disarmed and then re armed On Seal means the zone will restore as soon as the time out siren period is finished It can then be re triggered Press Press enter to save the Enter setting and move forward to the next feature Press 10 Enter Press Enter to move forward to the next feature 4 3 3 5 Siren Type Steady Press IO change the setting A detailed list of the settings is shown below Disable The siren will not sound for the chosen zone Steady means the siren will constantly sound when the chosen zone is triggered Pulsing means the siren will turn on then off every second Just Keypad means the keypad buzzer will sound only Press Press enter to save the Enter setting and move forward to the next feature Press 12 Enter Press Enter to move forward to the next feature RhinoCo Technology O 2002 48 SMS8 Series 4 3 3 6 Zone Isolation 1 3 Isolation 1 f e Yes Menu i i l Press kl to change the setting A detailed list of the settings is shown below No will disable the zone from being isolated Yes will enable the zone to be isolated Press Press enter to save the Enter setting and move forward to the next feature Press 12 Enter Press Enter to move forward to the next feature 4 3 3 7 Home Mode 14 Home mode 1 ES
40. ng 5 258 i i i i Press vd to change the Alarm Reporting setting A detailed list of the settings is shown below Note the zone number on the top right hand side of the display After pressing Enter repeatedly to scroll through the first set of features the same features will be displayed for the next zone Yes Will enable the dialer when an alarm event occurs No Will disable the dialer when an alarm event occurs Press Press enter to save the new Enter setting and move to the next feature Press Enter to move forward Press 6 Enter to the next feature 4 3 7 1 2 Restore Reporting Menu Press kd t0 change the Restore Reporting setting A detailed list of the settings is shown below 7 Restore 1 e Yes Yes Will enable the dialer when a restore event occurs No Will disable the dialer when a restore event occurs Press Press enter to save the new Enter setting and move to the next feature Press Enter to move forward to the next feature RhinoCo Technology 2002 SMS8 Series 73 4 3 7 1 3 Isolation Reporting 9 i i i i Press to change the Isolation Reporting setting A detailed list of the settings is shown below Yes Will enable the dialer when an isolation event occurs No Will disable the dialer when an isolation event occurs Press Press enter to save the new Enter sett
41. o move forward to the next feature RhinoCo Technology 2002 SMS8 Series 53 7 Fire e Menu N Enter Y 4 3 4 3 Fire Siren Press Enter Press Enter to select the panic option Siren Type Pulsing The display will show the following Press Menu to select one of the options E Press ST to keep the current setting or press Cancel LE repeatedly to exit below back to the previous menu Disable Disables panic from triggering the siren Steady Enables the siren to sound steady when panic is triggered Pulsing Enables the siren to turn on then back off every second when panic is triggered Just Keypad is triggered Enables only the keypad to buzz when panic Press Enter Press Enter to save your choice and move to the next menu 8 Press Enter to go to the next menu l Press Cancel SS Repeatedly to go back to the ready screen RhinoCo Technology 2002 54 4 3 SMS8 Series 5 Option 4 Timers Control 1 Once you enter option 4 from installers mode or from the previous menu the display will show the following Benn mer N Enter Y Press Press Menu to select the next Cancel menu or press repeatedly to exit back to the ready screen Zi Press Enter Press Enter to select the Cntrl Timers menu 3 Entry Delay D 10s 4 3 5 1 Entry Dela
42. oCo Technology 2002 SMS8 Series 67 4 3 6 5 Receiver 1 Format Type ep Press kd to change the format of Receiver 1 Phone A detailed list of the settings is shown below CID Contact ID for Back To Base monitoring via fixed line SMS Short Message Services for text messages to your mobile phone via fixed line Press Press enter to save the new Enter setting and move to the next feature Press 12 Enter Press Enter to move forward to the next feature RhinoCo Technology 2002 SMS8 Series 4 3 6 6 Receiver 2 Format Type 1 3 Rec2 Form e CID Menu Press kl to change the format of Receiver 2 Phone A detailed list of the settings is shown below CID Contact ID for Back To Base monitoring SMS Short Message Services for text messages to your mobile phone GSM Not in use Press Press enter to save the new Enter setting and move to the next feature Press Enter to move forward to the next feature RhinoCo Technology 2002 SMS8 Series 69 4 3 6 7 Report Routing Routine 1 Menu 5 m Press kl to change the route setting A detailed list of the settings is shown below Rec1 Only The alarm will only dial Phone 1 Rec2 Only The alarm will only dial Phone 2 SMS8 Version only Rec 1 amp 2 The alarm will dial Phone 1 and Phone 2 Rec 2 Back The alarm will dial Phone 1 If connection
43. of control panels or its peripherals The purchaser assumes all responsibility in the use of any RhinoCo control panel and its peripherals RhinoCo Technology 2002 SMS8 Series 7 1 1 Specifications v supported SMS8 SMS8GS X not supported Stand M ard Extend ed 8 Zones Maximum of 8 User Codes One Installer Code Siren Output rating 700mA Strobe Output rating 700mA Auxiliary Power rating 700mA Switched Auxiliary rating 200mA Maximum of 4 Keypads Dialler Contact ID and SMS Protocols Short Circuit protection all outputs Backup to GSM Pure GSM SR RR H RR RR 1 1 1 Approvals This panel meets the following safety and technical standards set by the Australian Communication Authority Applies to both SMS8 amp SMS8GSM A tick C tick a N11156 N11156 RhinoCo Technology O 2002 8 SMS8 Series 1 2 What You Get Below is a list of parts included with system Item Description Quantity Image 1 Control Panel This All In One unit incorporates the brain of the system This include the built in telephone dialer for 1 when something goes wrong and for back to base reporting functions It also includes the metal case 2 Keypad This keypad has a large 2 line LCD display screen and os additional LED indicators that show the alarms current 1 e state armed or disarmed It is used to arm disarm the system and other
44. ogy 2002 16 SMS8 Series Example Siren Box Mounting 1 Drill mounting holes 7mm diameter 25mm minimum in depth into the chosen wall Use a green star plug Press each one into the 4 main mounting holes Make a hole push the wires through the wall and up into the ceiling Screw the top 2 screws half way in Place the unit to support itself from the top 2 screws through the key shape holes at the top of the main unit Screw in and tighten the bottom two mounting screws then tighten the top two screws RhinoCo Technology 2002 SMS8 Series 17 Vy Wiring Control Panel 2k2 Resistor DC Siren Strobe Tamper Outside Siren Box Note The DC Siren Strobe Tamper Screamer and Outside Siren box are sold separately Generally the positive wire from each component such as the strobe and siren is red in colour or contains a red trace The negative wire from each component is generally black or contains a black trace General Rule RED Positive BLACK Negative RhinoCo Technology 2002 Rhine 18 SMS8 Series 2 5 The Screamer EG gt B Description Please note A screamer is not generally supplied with this alarm panel but may be included with special bundled packages Screamers are available and sold separately if one hasn t been included with your package Standard scre
45. output to rest at 12V and go open circuit when triggered No Does not send any message for telephone line faults Yes Sends a message if the phone line is not working for more than 15 minutes Press Press enter to save the new Enter Enter setting and move to the next feature Press Press Enter to move forward to the next feature S Enter 4 3 5 11 RF Tamper Bl Press to change the RF Tamper setting A detailed list of the settings is shown below RF version only This is to enable the tamper switch on the RHINOCO Wireless devices to set the alarm off whether the system is in the arm or disarm state No This will disable tamper on wireless detectors connected through an SMS8RX receiver Yes This will enable tamper on wireless detectors connected through an SMS8RX receiver Press Press enter to save the new Enter Enter setting and move to the next feature Press S Enter Press Enter to move forward to the next feature RhinoCo Technology 2002 SMS8 Series 61 2 1 Dial Enable e No 4 3 5 12 Dial Enable Menu Press to change the Dial Enable setting A detailed list of the settings is shown below This feature enables the panel to dial phone numbers in case of an alarm No This will disable the dial from sending any messages Yes This will enable the dialer to send messages Press Press
46. r End You will receive this message when the alarm has AC Account No 9991 Ac Ok power restored End RhinoCo Technology O 2002 SMS8 Series 3 5 How To Isolate Zones 1 Ready 29 Ensure the keypad is displaying Ready vONEer AUST HAL rowe 3 Dress Press the Menu Key e Menu ka 3 The display will show the G Isolate Zone Menu N Enter Y following times out in 10 seconds Press Enter Press the Enter Key to select isolate zones The display will show the following Enter the master user code Press the Enter Key The display will show the following RhinoCo Technology O 2002 20 SMS8 Series 9 Press Press the zone number you 3 Cameo wish to isolate Pressing 3 will isolate zone 3 Kg This is an example only The display will show the oo Zone NO 3 following Not Isolate P Brows 10 1 1 Press Press the menu key to e Menu toggle between not You may change isolate and isolate the isolation setting for multiple zones 1 3 Dress i e Enter move to the next zone and save any change Press the Enter key to Press the L button to go back one zone 1 3 Hold for 2 seconds Press the cancel button for e Cancel 2 seconds to exit back to the ready screen NOTE ISOLATED ZONES Isolated zones will be displayed as shown below from the ready screen Th
47. r from the previous menu the display will show the 1 following m Press Press Menu to select the next 8 8 Meng Event Report menu or press A a repeatedly to exit back to the ready screen 3 Press Enter Press Enter to select the Cntrl Timers menu 3 Account e 000001 4 3 6 1 Account Number Enter the new 6 digit account Cancel number Press LYE repeatedly to exit and disregard any If you have a 4 digit account changes number then use two leading zero s eg 003234 This number is sent on SMS messages and used as an identification if multiple panels are reporting back to one number If using back to base monitoring this number must be allocated by the monitoring company or control room Press Press enter to save the new Enter account number 4 Press e Enter RhinoCo Technology O 2002 64 SMS8 Series 4 3 6 2 Phone Number 1 Phone e 5 01234567 m Enter the new phone number for Cancel Phone 1 Press L repeatedly to exit and disregard any changes This number is sent on SMS messages and used as identification if multiple panels are reporting back to one number If using back to base monitoring this number must be allocated by the monitoring company or control room Panic Press w IO Move the cursor back one space a Medical Press L t0 move the cursor forward one space on Arm Press to delete the digit on the cursor
48. ries 2 6 The Sensors gt g Description Other optional accessories may include Passive Infrared Sensors Reed Switches Panic buttons Smoke sensors Other various sensors are also available Py Mounting Refer to the instructions supplied separately with each sensor you include with or add to the system Vy Wiring Refer to the instructions supplied separately with each sensor you include with or add to the system Generally each zone could contain multiple sensors wired in series but the number of sensors on each zone should be kept to a minimum Each sensor is powered from the two terminals on the control panel labelled as SWAUX and COMM these terminals are side by side Together these terminals supply a 12 Volt DC supply to the sensors No more than 800mA of electrical current should be drawn from these terminals ZONE INPUTS Connect the sensors to the terminal labelled Zx and C Where X is a spare available zone terminal on the panel RhinoCo Technology 2002 SMS8 Series 21 2 7 The Backup Battery You should only connect the backup battery once the wiring has been completed The back up battery should be connect FIRST before connecting the Mains AC Adaptor This panel has been specifically designed to only use a 12 Volt 7 Ampere hour 12 V 7AH Sealed Lead Acid Battery Connect the red wire from the alarm panel to the positive terminal of the backup bat
49. st of the settings is shown below The times are in minutes This is the maximum time allowed for the AC power to be off from the panel before the AC FAIL message is generated if programmed 15m 30 m 45m 60 m Press Press enter to save the new Enter setting and move to the next feature 10 Press Enter Press Enter to move forward to the next feature 1 1 Batt Offset e 0 4 3 5 7 Battery Offset Menu Press to change the Battery Offset setting A detailed list of the settings is shown below The times are in hours This feature allows the user to select what time of the day the panel will perform a battery test This will be performed the chosen number of hours after you exit programming mode eg If you choose 2h then the battery test will be performed 2 hours after you exit programming mode This will also assign what time of the day the panel will dial out if it is programmed in option 6 Program Event Reports 0 1h 2h 22h 23h increments up by 1 hour Press Press enter to save the new Enter setting and move to the next feature 12 Press Enter l y Press Enter to move forward to the next feature RhinoCo Technology 2002 58 SMS8 Series 4 3 5 8 Battery Period 1 3 S ms Press to change the Battery Offset setting A detailed list of the settings is shown below Description 24h Sends
50. tedly until the Ready screen is displayed Dial Test Menu N Enter Y Press Menu e 3 5 3 Dial Test Press Enter A test message will be sent to the control room s and or the mobile phone s as programmed Make sure that the DIALLER is enabled in the TIMER CONTROL option 4 Also make sure the correct TELEPHONE NUMBER and COMMUNICATION FORMAT are selected Upon successful completion of the test report the unit will respond with TEST PASSED Press DI to exit the menu An SMS message will appear as shown if programmed ACC N0001 Test DIALLER TEST MUST is enabled for this test to work refer to Installer Programming Dialler Programming NOTE If 3 beeps are heard while attempting to complete a dial test The DIALLER ENABLED option has not been turned on RhinoCo Technology O 2002 SMS8 Series 33 3 5 4 nual Test S ED Test NES ED N Enter Y Enter The battery test performs a dynamic test of the battery under load by disconnecting the AC supply from the charger this test will take approximately 2 minutes and upon completion of the test and depending on the condition of the battery the unit will respond with TEST PASSED or TEST FAIL Cancel Press the er button to go back to the test menu or press the LU button repeatedly to go back to the ready screen Press Menu to go back to the zone test menu OR Press Cancel Repeatedly to go back to the re
51. tery and the black wire to the negative terminal of the backup battery 2 8 AC Power Mains power is supplied from a 1 6VAC 25 VA plug pack transformer Connect the plug pack or transformer to the terminals labelled AC The Green or Green Yellow wire from an Australian plug pack is generally the Earth Wire and should be connected to the earth point on the panel The other 2 AC Wires can be connected to the AC terminals The AC wires may be placed either way to the AC terminals They are not polarity conscious due to the nature of the AC power signal RhinoCo Technology 2002 22 3 Operation SMS8 Series 3 0 How To Arm The System Before arming the system the system in any mode the keypad must display READY If it is not ready then it is due to a zone being open or triggered This may mean that a window has been left open a door is still open or there is movement within the building bh P Browne The keypad must display Ready before you are able to arm the system Enter a valid user code default is 1234 Press the ENTER key During the exit delay the keypad will display Exit now The keypad will display Armed when the system is fully armed and the armed light will turn on The strobe will flash for 1 5 seconds RhinoCo Technology O 2002 SMS8 Series 23 3 1 How To Quick Arm The System Use this to arm the system witho
52. ut having to enter a user code The keypad must display Ready before you are able to arm the system Press the Q H Arm button to arm the system without having to enter a user code During the exit delay the keypad will display Exit 99 now The keypad will display Armed The strobe will flash for 1 5 seconds and the Armed light will turn on RhinoCo Technology 2002 24 SMS8 Series 3 2 How To Home Arm the System STAY NOTE If no zones are programmed to be activated when in HOME mode Home arm is automatically disabled This mode is used when protecting your home or office while you are there The keypad must display Ready before you are able to arm the system 3 Press for 2 seconds f e O H Arm Hold the Q H Arm button to home arm the system without having to enter a user code During the exit delay the keypad will display Exit now Ow HomeARM e Groven The keypad will display Home ARM and the ARMED light will turn on 3 3 How To Disarm The System 1 GE Jes L Enter a valid user code default is 1234 3 Press D Enter Press the ENTER key then the system will disarm The keypad will display Ready The strobe light will flash for 4 seconds and the armed light will turn off RhinoCo Technology 2002 SMS8 Series 25 3 4 Phone Operations 3
53. y Menu Press vd to change the Entry Delay setting A detailed list of the settings is shown below The times are in seconds This feature determines the amount of time the user has to enter and disarm the system before an alarm is generated 5s 30s 75s 10s 45s 90s 20s 60s Press Press enter to save the new Enter setting and move to the next feature 4 Press Enter Press Enter to move forward to the next feature RhinoCo Technology 2002 SMS8 Series 55 3 Exit Delay D 10s 4 3 5 2 Exit Delay Menu Press IO change the Exit Delay setting A detailed list of the settings is shown below The times are in seconds This feature determines the amount of time that the user s has to exit the premises 5s 30 s 75s 10s 45s 90s 20s 60s Press Press enter to save the new Enter setting and move to the next feature i 4 Press Enter Press Enter to move forward to the next feature 5 Siren Time e 2m 4 3 5 3 Siren Time Menu Press d to change the Siren Time setting A detailed list of the settings is shown below The times are in minutes This is the duration that the siren will be on for when in alarm 2m 5m 7m 10m Press Press enter to save the new Enter setting and move to the next feature Press Enter Press Enter to move forward to the next feature
Download Pdf Manuals
Related Search