Home

H1, H2 and H3 Operation Manual

1. 15 ILLUSTRATION 7 SOLID WOOD OVERLAY PANEL 16 ILLUSTRATION 8 GLASS WOOD OVERLAY PANEL 16 ILLUSTRATION 9 WOOD DRAWER OVERLAY nds 17 STORAGE CAPABILITES Ne Mu 16 17 WOODEN WINE RACK TRIM 18 ILLUSTRATION 10 WOODEN WINE RACK TRIM DESIGN 18 LOCK INSTALLATION ei eee eine eee menn 19 DRAWERS ABD 5 meere 19 ILLUSTRATION 11 DOOR LOCK INSTALLATION OPERATION ar MEME SINGLE DOOR FREEZER OPERATION 20 SINGLE DOOR REFRIGERATOR 20 SINGLE DOOR WINE COOLER OPERATION sel TWO DOOR FREEZER REFRIGERATOR OPERATION 22 TWO DOOR ALL REFRIGERATOR OPERATION 22 TWO DOOR ALL WINE COOLER 23 TWO DOOR MULTI ZONE WINE COOLER OPERATION 24 TWO DOOR REFRIGERATOR WINE COOLER OPERATION 25 THREE DOOR FREEZER REFRIGERATOR REFRIGERATOR OPERATION 2 die eere eere tee 26 THREE DOOR FREEZER REFRIGERATOR WINE COOLER OPERA TON ett entree tte ir 26 THREE DOOR ALL REFRIGERATOR OPERATION 27 THREE DOOR ALL WINE COOLER 28 THREE DOOR THREE ZONE WINE COOLER OPERATION 29 THREE DOOR TWO ZONE WINE COOLER OPERATION 30 THREE
2. Unit shown with door mounted on left hand side available from factory mounted either left or right exception is workboard units which only come mounted on left All doors can be changed by customer Remove TOP HINGE PIN Use caution with Tools Required REMOVAL OF DOOR Large Flat Head Screwdriver Regular Philips Head Screwdriver Small Philips Head Screwdriver STEP 1 STEP 5 FNA STEP 3 screwdriver so as not to STEP 1 After removal of HINGE PIN carefu ly tilt door out of BRACKET and lift away from BOTTOM HINGE PIN set door to the side STEP 5 STEP 2 Remove HOLE PLUGS on right side of unit Plugs fit very tightly into holes be careful not to scratch front surface of unit during removal Top and bottom plugs need to be removed DO NOT discard STEP 3 Remove top and bottom m HINGE BRACKETS from unit o Remove DOOR CLOSING INSERT and HINGE PIN from BOTTOM HINGE BRACKET of unit See detail view at bottom of page Remove BOTTOM HINGE BRACKET of door to allow removal of the DOOR CLOSING INSERT immediately replace BOTTOM HINGE BRACKET Remove TOP HINGE BRACKET from door to allow assembly of the DOOR CLOSING INSERT which was removed from the BOTTOM HINGE BRACKET to the door after adding the INSERT gt
3. Detail view of entire BOTTOM DOOR HINGE assembly DOOR HINGE BRACKET UNIT HINGE DOOR E 0 Q0SNG 11 INSERT EES PIN www bringperlickhome com 12 STEP 4 HOLE PLUGS to be inserted into vacant Left Hung door mounting holes DO NOT HIT WITHA HAMMER as it may damage unit face Instead use handle of hammer or block of wood to push plugs into holes STEP 5 Door bottom on the right mounted version was door top on left mounted version Before attempting to re mount door move into place to verify that The DOOR HANDLE will stay on the outside of the door swing The DOOR CLOSING INSERTS on both the door and the unit are on the bottom All screws are tight using hand tools over tightening with power tools may result in damage to the unit RE HANGING OF DOOR STEP 6 TOP HINGE PIN tobe inserted last DOOR must be gently lifted onto BOTTOM HINGE PIN then tilted into place before TOP PIN can be added to finish the Installation STEP 1 LOWER LEFT HINGE BRACKET rotates 180 and becomes UPPER RIGHT HINGE BRACKET STEP 2 TOP LEFT HINGE BRACKET rotates 180 and becomes BOTTOM RIGHT HINGE BRACKET STEP 3 BOTTOM HINGE PIN and DOOR CLOSER INSERT assemble to BOTTOM RIGHT HINGE BRACKET www bringperlickhome com 13
4. Turn hand valve counterclockwise on CO2 cylinder to the fully open position Turn regulator adjusting screw clockwise until desired pressure is reached approximately 12 15 Ibs Tighten stop nut on adjusting screw W Open shut off valve on bottom of regulator ORPORATION Form No 22259 Rev 1 17 05 www bringperlickhome com 46 Installation and Tapping Direct Draw Dispensers Self Contained CO2 Leak Test Dilute a small amount of liquid dishwashing soap and rub the soapy mixture around each connection If bubbles appear tighten connection Replacing CO2 Gas Cylinder Turn CO2 hand valve clockwise until seated and close shut off valve on regulator W Unscrew regulator from cylinder fitting Replace carbonic washer Part No 157F2P if needed and reattach regulator to filled cylinder Turn CO2 hand valve counterclockwise until fully open Turn regulator shut off valve to open position Adjust gas flow as required turning clockwise for higher pressure Failure to heed the warnings on this page could result in personal injury or death Beverage systems pressur ized with carbon dioxide or nitrogen must be equipped with two safety relief ae valves one at the cylinder H regulator and the other in the gas line upstream on the product tanks Temperature Proper CO2 Handling ALWAYS Connect a regulator reducing valve t
5. Wine Cooler Section 2 Wine Cooler Section 3 38 F 55 F H3RWW 38 F 55 F 65 F 55 F 65 F 55 65 45 55 65 www bringperlickhome com Range Range Range Range Range Range Range Range Range Range Range Range Range Range Range Range Range Range Range Range Range Range Range Range Range Range Range Range Range 5 F to 5 F 33 F to 43 F 44 F to 68 F 5 F to 5 F 33 F to 43 F 33 F to 43 F 44 F to 68 F 33 F to 43 F 50 F to 60 F 44 F to 56 F 54 F to 68 F 5 F to 5 F 33 F to 43 F 5 F to 5 F 36 F to 42 F 50 F to 60 F 33 F to 43 F 44 F to 68 F 33 F to 43 F 33 F to 43 F 50 F to 65 F 33 F to 43 F 45 F to 56 F 55 F to 68 F 44 F to 56 F 54 F to 68 F 44 F to 56 F 54 F to 68 F 44 F to 48 F 50 F to 58 F 60 F to 68 F 37 CHECKING PRODUCT TEMPERATURE To accurately check the temperature of the product stored in a refrigerated compartment insert an accurate thermometer into a plastic non breakable bottle partially filled with water Tighten the bottle cap securely Place the bottle in the desired area for 24 hours Refrain from opening the unit during the testing period After 24 hours check the temperature of the water Adjust the control settings if necessary and re test Your Perlick refrigerated ca
6. e 15 your condenser area clean www bringperlickhome com 40 The refrigerated compartment is warmer than usual Is your control set properly Is the light staying on Is your condenser area clean and free of obstructions Has the door been open for a long time or more frequent door openings occurred Are the internal louvers and fan guard openings obstructed Has warm product just been placed in the cabinet The refrigerated compartment is colder than usual e your control set properly e s your door closing and sealing properly e 15 the ambient temperature within the normal operating range The refrigeration system runs for long periods of time e Is the condenser area clean and free of obstructions e Have the doors been open for a long time or more frequent door openings occurred Have warm product just been placed in the cabinet e hot days and in warm room temperatures the system will run long Condensation forms inside the refrigerated compartments e This is normal during high humidity and frequent door openings e Are the doors closing and sealing properly Condensation forms on the outside of the unit During periods of high humidity some condensation might appear on outside surfaces The condensation will disappear when the humidity drops Meanwhile be sure doors are closing and sealing properly If condensation persists contact your Perlick Factory Authorized Service Center You
7. INTRODUCTION Congratulations on your purchase of a Perlick residential refrigeration product A pioneer in the commercial refrigeration field for nearly 60 years Perlick has decided to bring the ultimate in beauty high quality and innovative commercial products to the residential market The vast product offering available in both indoor and outdoor models gives you the opportunity to enjoy the functionality and user friendliness in just about any setting including home hospitality centers kitchens bedrooms and summer rooms in either a built in or freestanding model The all stainless interior and front face will provide beauty and durability for a lifetime of use This Installation and Use and Care Guide will answer your questions about the features operation and maintenance of your Refrigerated Cabinet model If you have questions that are not addressed here call 800 558 5592 IMPORTANT PLEASE READ all instructions completely before attempting to install or operate the unit First as you follow these Installation and Use and Care instructions take particular note of the CAUTION and WARNING symbols when they appear This information is important for the safe and efficient installation operation and care of your Perlick Refrigerated Cabinet CAUTION Signals a hazard where minor injury or product damage may occur if you do not follow instructions WARNING States a hazard may cause serious injury or death if pr
8. Plug the unit into the 15 amp grounded outlet located in the cabinet installation opening With power applied to the appliance check for lighting and cooling before going any further Once you are satisfied the unit is operating properly turn off the power to the wall outlet at the circuit breaker and proceed SHUT OFF POWER TO THE WALL OUTLET BEFORE INSTALLING INTO THE OPENING Check the surrounding cabinetry to ensure that the front face and interior opening is level and square Check to ensure the entire floor where the cabinet is to be installed is level Check that the countertop bottom front edge is level If all surfaces are level measure from the floor to the bottom of the front edge of the countertop Measure the rear of refrigerated cabinet from floor to top of cabinet at back corners Adjust rear corner leveling legs to achieve identical measurements as previously measured from floor to bottom edge of countertop Adjust legs by turning counterclockwise to raise the unit and clockwise to lower the unit using an adjustable wrench or pliers Once measurements are identical and if the cabinet has additional leveling legs on rear of cabinet adjust to proper height to support center of cabinet IMPORTANT NOTE Leveling legs should not be extend more than from bottom of the cabinet IMPORTANT NOTE The floor under the Perlick cabinet must be at the same level as the surrounding finished floor www bringperlickhom
9. DOOR OPTIONS Perlick Residential Refrigerated cabinets offer a variety of door panel design alternatives solid stainless steel solid wood overlay stainless steel glass and wood overlay glass This together with door swing choices result in a variety of possible combinations Solid stainless steel and stainless steel glass doors are shipped from the factory with decorative stainless steel panels and handles in place on the appliance ready for use Solid wood overlay and glass wood overlay doors are designed to accept a decorative front panel to match surrounding cabinetry and door handles This panel and door handle will be provided by the customer All Perlick Refrigerated cabinets accept of the above door configurations and are fully hinge reversible and interchangeable IMPORTANT NOTE DRAWERS CAN REPLACE ANY SECOND OR THIRD DOOR ON A MULTI DOOR CABINET WITH THE ADDITION OF A FACTORY INSTALLED MULLION IMPORTANT NOTE CABINETS WITH A FIRST DOOR FREEZER CAN ONLY UTILIZE A SOLID STAINLESS STEEL DOOR OR A SOLID WOOD OVERLAY DOOR STAINLESS STEEL GLASS OR WOOD OVERLAY GLASS DOORS WILL SWEAT IF INSTALLED ON A FREEZER SECTION IMPORTANT NOTE STAINLESS STEEL GLASS OR WOOD OVERLAY GLASS DOORS MAY SWEAT IN CONDITIONS WITH RELATIVE HUMIDITY OVER 75 INSTALLATION OF WOOD OVERLAYS Before beginning installation check for the correct components for the fit and finish desired All overlay doors require a trim panel
10. att 6 54 4 21812212 INGWINVGWOS MSG wowa 2 INGWISVdWOS MSQ Woldlosta 153418740402 vr E ve ve vs 5 19 A mut mi Pres mar A 1 TE TET Fi I E E tt B OR JR s PR m 8 p xov xov by oe i oe T Emi IHA 450 X8 N3v 40 1 40 img 3me IN3ALSVOAWOO NOLLVH39IH338 IN3ALISVdAODO NOILVSd9OIHd38 MOLOW Xnv SAO IGNS HOIHM OOMZH 9 OOu H AHL SI NOlld39X3 SYOLOW YO 5505335 SBHJTIOMINOO 1 007 014 3 LON OQ SI3NVd H3QIAIG O M STSQOW 3MOOQ L In IN3AISVdAOO 1918438 0 SOH V 3AVH 58124344 8000 15414 AINO SDH ON 3 VH 29 YIH S T30ON AINO NOILO3S 1431 350 YIH 51300 DILVNSHOS NIXIM SLONGOdd 19 4444 SNOH JUHM Ne xov se NI JUHM H a aS wy L W49 INSNLEVdNOO 3NIHOVN www bringperlickhome com 42 PERLICK HOME REFRIGERATION PRODUCTS LIMITED WARRANTY ENTIRE PRODUCT Full Two Year Warranty For two years from the date of original installation Perlick Corporat
11. wine coolers this button has been disabled LIGHT All controllers are equipped with a soft light button on the front of the controller panel This button has been disabled and will not turn on the light in the cabinet The lights have a manual switch located near each light which can manually turn on the light for displaying product behind glass doors The light is also equipped with a door switch that turns on the light upon a door opening Leaving the light on for extended periods of time may increase the cabinet temperature and in turn product temperature especially in close proximity to the light at the top and cause the refrigeration system to run longer ADJUSTING THE SET POINT The set point is the temperature at which when obtained will cause the controller to turn off the cooling system To adjust the set point simply press the soft SET button located on the front of the controller panel Upon pressing the current set point will be displayed Press the UP or DOWN arrow buttons located on the front of the controller panel to the new desired set point The controller will now memorize this new set point IMPORTANT NOTE Dependent on the model and configuration the controllers have been programmed to only allow a temperature adjustment within a specified range see chart below for the specified range allowed for your cabinet www bringperlickhome com 36 CHART 1 PRODUCT TEMPERATUR
12. If manual light switch is left on for an extended period of time it may increase the cabinet temperature especially in close proximity to the light at the top and cause the refrigeration system to run longer THREE DOOR FREEZER REFRIGERATOR WINE COOLER OPERATION The Perlick Three Door Freezer Refrigerator Wine Cooler H3FRW comes equipped with a state of the art refrigeration system The compressor is of a variable speed variety which automatically changes speeds based on system conditions and load The cabinet is equipped with three adjustable digital temperature controllers and LED displays The freezer controller can be adjusted through a range of 10 F to 10 F The freezer controller has been factory set to modulate from 3 F to 5 F The refrigerator controller can be adjusted through a range of 30 F to 42 F The refrigerator controller has www bringperlickhome com 28 been factory set to modulate from 37 F to 39 F The wine cooler controller can be adjusted through a range of 50 F to 60 F The refrigerator controller has been factory set to modulate from 54 F to 56 F To properly determine product temperature see CHECKING PRODUCT TEMPERATURE on page 44 IMPORTANT NOTE ALWAYS ALLOW CABINET TO RUN FOR A MINIMUM OF 24 HOURS TO ALLOW TEMPERATURE STABILIZATION AFTER START UP BEFORE STORING PERISHABLE ITEMS IMPORTANT NOTE PERLCK S MULTI ZONE UNITS ARE NOT DESIGNED FOR OUTDOOR APPL
13. OR DOORS AS STEPS OR TO SUPPORT MORE THAN THEY WERE DESIGNED TO SUPPORT CAUTION DO NOT LIFT UNIT BY DRAWER OR DOOR HANDLES FAILURE TO CLEAN THE CONDENSER EVERY THREE MONTHS CAN CAUSE THE UNIT TO MALFUNCTION THIS COULD VOID THE WARRANTY NEVER INSTALL THE UNIT BEHIND CLOSED DOORS BE SURE FRONT LOUVERED TOE PLATE IS FREE OF OBSTRUCTION OBSTRUCTING FREE AIRFLOW CAN CAUSE UNIT TO MALFUNCTION AND MAY VOID THE WARRANTY CAUTION USE ONLY GENUINE PERLICK REPLACEMENT PARTS IMITATION PARTS CAN DAMAGE THE UNIT AND MAY VOID THE WARRANTY INSTALLATION INSTRUCTIONS IMPORTANT NOTE The information in this installation guide applies to all product models unless noted www bringperlickhome com ILLUSTRATION 1 INSTALLATION SPECIFICATIONS Height 34 1 2 inches Depth 24 inches same across all units One door width 24 inches Two door width 48 inches Three door width 72 inches Finished rough opening requirements 34 3 32 NOTE All electrical instructions assume that outlet is located 4 10 inches from floor Floor must be level in area of installation leg levelers are meant as a means of fine tuning not recommended for making up differences in the floor surpassing 1 2 inch When moving the units into place take care to protect the floor as necessary with cardboard rugs etc Never attempt to move unit w
14. PRODUCT TEMPERATURE UNDER THESE CONDITIONS A 6 F OR 2 F AIR TEMPERATURE SWING IN THE REFRIGERATOR WINE COOLER COMPARTMENTS DOES NOT CHANGE THE ACTUAL PRODUCT TEMPERATURE PRODUCT TEMPERATURE REMAINS AT A VERY STABLE TEMPERATURE LIGHT SWITCH AND BULB Your Two Door Refrigerator Wine Cooler has two interior lights that are illuminated when each respective door is opened The cabinet also comes standard with manual light switches located next to each light for displaying your products through a glass door If manual light switch is left on for an extended period of time it may increase the cabinet temperature and in turn product temperature especially in close proximity to the light at the top and cause the refrigeration system to run longer OPERATION THREE DOOR e THREE DOOR FREEZER REFRIGERATOR REFRIGERATOR OPERATION The Perlick Three Door Freezer Refrigerator Refrigerator H3FRO comes equipped with a state of the art refrigeration system The compressor is of a variable speed variety which automatically changes speeds based on system conditions and load The cabinet is equipped with two adjustable digital temperature controllers and LED displays The freezer controller can be adjusted through a range of 10 F to 10 F The freezer controller has been factory set to www bringperlickhome com 27 modulate from 3 F to 5 F The refrigerator controller can be adjusted through a range of 30 F
15. from entering the bottle Do not block internal louvers or fan guard openings as this will decrease operating performance CONTROL SETTINGS The cabinet is shipped with the controllers turned ON To turn the refrigeration system OFF or ON press the blue soft button on the front face of the low temperature wine zone controller if the controller is turned off with power applied to the cabinet the LED display will read OFF when turned on it will read a temperature The low temperature wine zone controller is located on the top front face of the cabinet above the left door and is equipped with a tinted see through lens which opens by pulling out on the bottom of the lens and rotating upwards Always ensure lens cover is closed before closing door to avoid damage to the controller or lens The warm temperature wine zone controller appears identical except it controls this zones cooling system and is located above the right door The refrigerator zone electronic control comes preset for a product temperature of approximately 38 F with a product temperature adjustability range of 33 F to 43 F The wine cooler zone electronic control comes preset for a product temperature of approximately 55 F with a product temperature adjustability range of 50 F to 60 F To change temperature controller settings see section TEMPERATURE CONTROLLER ADJUSTMENTS on page 42 IMPORTANT NOTE THE LED DISPLAY IS READING ACTUAL AIR TEMPERATURE NOT
16. manual defrost soft button on the front panel signified by a melting snowflake which has been disabled for this model PROPER PRODUCT STORAGE This wine cooler will accommodate 42 bottles of wine Specially designed full extension wine racks allow for proper horizontal storage of the wine The cork remains moist which keeps air from entering the bottle Do not block internal louvers or fan guard openings as this will decrease operating performance CONTROL SETTINGS The cabinet is shipped with the controller turned ON To turn the cabinet OFF or ON press the blue soft button on the front face of the controller if the controller is turned off with power applied to the cabinet the LED display will read OFF when turned on it will read a temperature The controller is located on the top front face of the cabinet and is equipped with a tinted see through lens which opens by pulling out on the bottom of the lens and rotating upwards Always ensure lens cover is closed before closing door to avoid damage to the controller or lens The electronic control comes preset for a product temperature of approximately 55 F with www bringperlickhome com 22 a product temperature adjustability range of 42 F to 70 F To change temperature controller settings see section TEMPERATURE CONTROLLER ADJUSTMENTS on page 42 IMPORTANT NOTE THE LED DISPLAY IS READING ACTUAL AIR TEMPERATURE NOT PRODUCT TEMPERATURE UNDER T
17. 3 Connecting the 3 Adjusting Gas FloW 2 renes 3 618 24 RITE 4 Replacing CO2 Gas 4 Handing 09 dS iier ttr ttes 4 TEMPERATURE Beer 4 CLEANING Cleaning the Beer 5 Cleaning the Cabinet nee 5 GENERAL INFORMATION Troubleshootirig cci etit 6 6 How to Pour a Perfect Glass of 7 LOW Profle CoUpler onore ers 8 8300 West Good Hope Road Milwaukee WI 53223 Phone 414 353 7060 Fax 414 353 7069 Toll Free 800 558 5592 E Mail Perlick Perlick com www Perlick com Form No 22259 Rev 1 17 05 www bringperlickhome com 44 HOME TAPPED CABINET INSTALLING DISPENSING HEAD AND FAUCET BEFORE YOU BEGIN Wash tapping devices thoroughly Flush beer and faucet lines and tapping device keg coupler with fresh water Apply silicone around the base of the dispensing head to seal it to the top Align the dispensing head over the DISPENSING HEAD mounting holes on the cabinet top and secure using screws Wipe off excess silicone to complete the seal APPLY SILICONE TO 3 5 FAUCET LEAD BOTTOM PERIMETER 2 Attach faucet to dispensing head using spanner wrench to tigh
18. CAUSES Dirty glass Dirty faucet or beer line Frozen or nearly frozen beer Old beer Beer that has not been refrigerated for a long period of time Beer and CO2 Facts No of 1202 Servings 734 992 3 445 105 87 165 Quarter m Beer foam is 25 liquid beer and 75 CO2 gas Don t waste it W Most people prefer beer stored at 38 W Beer lines and faucets require regular cleaning see cleaning instructions on page 7 A fully charged 4 2 Ib CO2 cylinder will dispense approximately 512 to 6 half barrels m gas gives beer its sparkling effervescence It also gives beer its creamy head of foam No of Gallons No of No of Cases Full Keg Weight Perlick is committed to continuous improvement Therefore we reserve the right to change specifications without prior notice www bringperlickhome com 49 Pouring a Perfect Glass of Beer Direct Draw Dispensers STEP 1 Start with a clean glass Place the glass at a 45 angle one inch below faucet Do not let the glass touch the faucet Open the faucet all the way STEP 2 After the glass has reached half full gradually bring the glass to the upright position 41 STEP 3 Let the remaining beer run straight down the middle of the glass This ensures proper release of CO2 by producing 34 to 1 foam head STEP 4 Close the faucet quickly and co
19. DOOR REFRIGERATOR TWO ZONE WINE COOLER 31 TEMPERATURE renenn 32 TEMPERATURE CONTROLLER ADJUSTMENT S 32 CHART 1 PRODUCT TEMP SET POINTS AND RANGES 34 CHECKING PRODUCT 35 1 35 CLEANING cniinne aeee 35 LIGHT BULB 35 0 5 enna 36 GENERAL viens 36 WIRING 38 WARRANTY 39 www bringperlickhome com GENERAL PRECAUTIONS DANGER RISK OF CHILD ENTRAPMENT BEFORE YOU THROW AWAY YOUR OLD REFRIGERATOR OR FREEZER TAKE OFF THE DOORS AND LEAVE SHELVES IN PLACE SO THAT CHILDREN MAY NOT EASILY CLIMB INSIDE WARNING NEVER ATTEMPT TO REPAIR OR PERFORM MAINTENANCE ON THE UNIT UNTIL THE ELECTRICITY HAS BEEN DISCONNECTED ALTERING CUTTING OF THE POWER CORD OR REMOVAL OF THE POWER CORD REMOVAL OF POWER PLUG OR DIRECT WIRING CAN CAUSE SERIOUS INJURY FIRE AND OR LOSS OF PROPERTY AND OR LIFE AND WILL VOID THE WARRANTY THE ANTI TIP KIT MUST BE INSTALLED ON THIS UNIT BEFORE IT IS USED NEVER USE THE DRAWERS SHELVES
20. GROUNDING PRONG FROM THE PLUG e NEVER USE A TWO PRONG GROUNDING ADAPTER NEVER USE EXTENSION CORD TO CONNECT POWER TO THE UNIT WHERE A TWO PRONG WALL RECEPTACLE IS ENCOUNTERED OR A LONGER POWER CORD IS REQUIRED CONTACT A QUALIFIED ELECTRICIAN TO HAVE IT REPLACED IN ACCORDANCE WITH APPLICABLE ELECTRICAL CODES WARNING FAILURE TO COMPLY WITH THE ABOVE ELECTRICAL GUIDELINES MAY RESULT IN POSSIBLE INJURY DEATH FIRE OR LOSS OF PROPERTY www bringperlickhome com UNPACKING AND MOVING CAUTION DO NOT CUT CARDBOARD SLEEVE COVERING THE UNIT CUTTING MAY RESULT IN DAMAGE TO THE EXTERIOR OF THE CABINET Uncrate the unit outside on a flat level surface Remove the cardboard sleeve by removing the staples holding the sleeve to the wood shipping base Carefully lift the cardboard sleeve up over the top of the cabinet this should be done with a minimum of two people larger cabinets may require additional helpers Carefully cut the banding holding the cabinet to the wood shipping base Remove all packing materials from the interior of the cabinet and discard Remove door s drawers and all cantilever sliding or unfastened shelving from the cabinet To remove the door s remove the upper pivot pin using a standard straight blade screwdriver and turning the fastener counterclockwise always support the door when unfastening the upper pivot pin Once the upper pivot pin is loose pull the pin up and tip the door sl
21. SWITCH AND BULB Your Three Door Refrigerator Wine Cooler Wine Cooler has three interior lights that are illuminated when each respective door is opened The cabinet also comes standard with a manual light switches located next to each light for displaying your products through a glass door If manual light switch is left on for an extended period of time it may increase the cabinet temperature especially in close proximity to the light at the top and cause the refrigeration system to run longer www bringperlickhome com 34 TEMPERATURE CONTROLLER Front cover removed for clarity 63738 63699 Displays maximum stored temperature also used for navigating control codes and changing displayed values within the Turns on off the power to the unit various menu options Fast freezing Disabled cycle is started by holding button down for 3 Manually defrosts the unit by holding button down Displays minimum stored temperature also Displays and allows for modification of used for navigating control codes and target set point Used to select a changing displayed values within the parameter or confirm an operation in various menu options programming mode If held for 3 seconds while max or min temperature is displayed it will erase that temperature from memory L E D Alerts SYMBOL STATUS ALERT DEFINITION The compressor is running FLASHING Anti short cycle delay enabled Programming phase when f
22. additional black vinyl coated cantilever or pullout shelf can be used in this cabinet The second and third door wine cooler compartments each can hold 48 wine bottles THREE DOOR ALL WINE COOLER The three door all wine cooler H3WOO H3WOW H3WWO H3WWW comes standard with sixteen full extension black vinyl coated wine racks capable of storing 128 total wine bottles standard magnum or half size bottles An additional fixed storage rack is nestled into the lower step of the first door for storage of an additional 10 wine bottles standard magnum or half size bottles If the cabinet is a multi zone wine cooler the first door can hold 42 total wine bottles while the second door and third doors can each hold 48 total wine bottles www bringperlickhome com 18 ILLUSTRATION 10 WOODEN WINE RACK TRIM DESIGN 1 8 319 DEEP H l L d 1 2 L N 1 16 TO 1 8 18 5 16 RADIUS ALL UTSIDE EDGES WOODEN WINE RACK TRIM FINISHING The included unfinished faces can be finished and sealed many cases stains and or finishes have odors that may be objectionable in an enclosed area To remove the front wood face from the wine shelf simply pull out the wine shelf and remove the fasteners finish as desired and re install with fasteners All wine racks come with an unfinished solid hardwood face which can be removed and
23. also has a manual defrost soft button on the front panel signified by a melting snowflake which has been disabled on this model PROPER PRODUCT STORAGE The low temperature wine zone will accommodate 42 bottles of wine The high temperature wine zone will accommodate 48 bottles of wine Specially designed full extension wine racks allow for proper horizontal storage of the wine The cork remains moist which keeps air from entering the bottle Do not block internal louvers or fan guard openings as this will decrease operating performance CONTROL SETTINGS The cabinet is shipped with the controllers turned ON To turn the refrigeration system OFF or ON press the blue soft button on the front face of the low temperature wine zone controller if the controller is turned off with power applied to the cabinet the LED display will read OFF when turned on it will read a temperature The low temperature wine zone controller is located on the top front face of the cabinet above the left door and is equipped with a tinted see through lens which opens by pulling out on the bottom of the lens and rotating upwards Always ensure lens cover is closed before closing door to avoid damage to the controller or lens The warm temperature wine zone controller appears identical except it controls this zones cooling system and is located above the right door The low temperature wine zone electronic control comes preset for a product temperature of a
24. at least 3 4 thick The solid wood overlay panel should not weigh more than 20 pounds The glass wood overlay panel should not weigh more than 10 pounds The solid wood drawer overlay panels should not weigh more than 10 pounds each This section gives detailed instructions of how to install a solid wood overlay or glass wood overlay panel and handle to a Perlick Customizable door or drawer NOTE CONTACT THE FACTORY FOR FULL SIZED WOOD OVERLAY PANEL LAYOUTS See Illustration 7 for details for the design of a solid wood overlay panel See Illustration 8 for details for the design of a glass wood overlay panel See Illustration 9 for details for the design of a solid wood drawer overlay panel Inspect the wood door panel for the proper design specified in the previous illustrations The handle must be attached to the wood panel The handle must be attached to that first IMPORTANT NOTE HANDLE MOUNTING ON WOOD OVERLAY DOOR SHOULD ALWAYS BE MOUNTED ON WOOD OVERLAY ONLY TO AVOID DAMAGE TO FACTORY DOOR SEE PREVIOUS DESIGN ILLUSTRATIONS FOR ACCEPTABLE HANDLE MOUNTING HARDWARE PASSAGE THROUGH WOOD OVERLAY PORTION OF THE DOOR SO FASTENERS DO NOT INTERFERE To attach the door handle to wood overlay panel first decide which direction the door will be hinged Once decided mark rear of wood overlay panel with handle fastener location s Drill through wood overlay panel at marked handle fastening location s taking proper care t
25. different door hang options desired height at the 45 degree angle push in the hook to the back rail rotate toward wall and set front section on the wall hook To return shelf first push both extenders completely in then line up the shelf grooves and slide easily into the unit Wine Shelving See Full Extension shelving Note All shelving is inter changeable with all products Drawers To remove fully extend the drawers Hold on to both side and pull straight up and out To return drawers fully extend the extenders Line up the back slots first keep the extender completely out then set the back slots down into place Next easily set down the front Caution COMPLETELY EMPTY THE DRAWER BEFORE REMOVING www bringperlickhome com 20 OPERATION SINGLE DOOR e SINGLE DOOR FREEZER OPERATION The Perlick Single Door Freezer H1F comes equipped with a state of the art refrigeration system The compressor is of a variable speed variety which automatically changes speeds based on system conditions and load The cabinet is equipped with an adjustable digital temperature controller and LED display The controller can be adjusted through a range of 10 F to 10 F The controller has been factory set to modulate from 3 F to 5 F To properly determine product temperature see CHECKING PRODUCT TEMPERATURE on page 44 IMPORTANT NOTE ALWAYS ALLOW CABINET TO RUN FOR A MINIMUM OF 24 HOURS T
26. replaced with other wood to match your cabinetry See design illustration 10 below for wine rack face details www bringperlickhome com 19 LOCK INSTALLATION amp REVERSING A Door Lock Kit can be ordered as an opening kit To install or remove the lock remove the three fasteners holding the Lock Mechanism to the cabinet and the three fasteners holding the Lock Bracket to the door accessory Two kits are available a right hand opening and a left hand ILLUSTRATION 11 DOOR LOCK INSTALLATION LOCK MECHANISM gets screwed to the unit screws are hidden and protected when door is shut LOCK BRACKET is screwed to the door SHELVING AND DRAWERS Shelving Perlick has three different types of shelving All designed to easily be moved and adjusted Cantilever is stationary shelving It can be moved up and down for desired heights Pick up the shelving by pulling up and unhooking the back hooks from the railing Move to desired height then place the hooks in the railing and set down Full extension Shelving Pull the shelf out to its farthest point Locate the tabs in the middle on both sides of the extenders Press tabs and pull shelf out Move each extender separately Hold the Middle of one extender pull the front up then rotate to the inside of unit Once at a 45 degree angle pull up then pull out Place extender at Note Different Lock Mechanism and bracket are required for
27. to 42 F with an adjustable differential to optimize storage conditions The refrigerator controller has been factory set to modulate from 37 F to 39 F To properly determine product temperature see CHECKING PRODUCT TEMPERATURE on page 44 IMPORTANT NOTE ALWAYS ALLOW CABINET TO RUN FOR A MINIMUM OF 24 HOURS TO ALLOW TEMPERATURE STABILIZATION AFTER START UP BEFORE STORING PERISHABLE ITEMS IMPORTANT NOTE PERLCK S MULTI ZONE UNITS ARE NOT DESIGNED FOR OUTDOOR APPLICATIONS INSTALLING MULTI ZONE UNITS OUTDOORS WILL VOID THE WARRANTY This cabinet is a frost free model meaning the evaporator cooling coil automatically defrosts on demand at predetermined intervals The controller also has a manual defrost soft button on the front panel signified by a melting snowflake If depressed it will automatically put the system into a defrost cycle PROPER PRODUCT STORAGE Store product as desired Do not block internal louvers or fan guard openings as this will decrease operating performance CONTROL SETTINGS The cabinet is shipped with the controllers turned ON To turn the refrigeration system OFF or ON press the blue soft button on the front face of the freezer controller if the controller is turned off with power applied to the cabinet the LED display will read OFF when turned on it will read a temperature The freezer controller is on the top front face of the cabinet above the left door and is equipped with a tinted
28. ABINET TO RUN FOR A MINIMUM OF 24 HOURS TO ALLOW TEMPERATURE STABILIZATION AFTER START UP BEFORE STORING PERISHABLE ITEMS IMPORTANT NOTE PERLCK S MULTI ZONE UNITS ARE NOT DESIGNED FOR OUTDOOR APPLICATIONS INSTALLING MULTI ZONE UNITS OUTDOORS WILL VOID THE WARRANTY This cabinet is a frost free model meaning the evaporator cooling coil automatically defrosts during off cycles The controller also has a manual defrost soft button on the front panel signified by a melting snowflake which has been disabled on this model PROPER PRODUCT STORAGE This low temperature wine zone will accommodate 42 bottles of wine The medium temperature wine zone will accommodate 48 bottles of wine The high temperature wine zone will accommodate 48 bottles of wine Specially designed full extension wine racks allow for proper horizontal storage of the wine The cork remains moist which keeps air from entering the bottle Do not block internal louvers or fan guard openings as this will decrease operating performance www bringperlickhome com 31 CONTROL SETTINGS The cabinet is shipped with the controllers turned ON To turn the refrigeration system OFF or ON press the blue soft button on the front face of the low temperature wine zone controller if the controller is turned off with power applied to the cabinet the LED display will read OFF when turned on it will read a temperature The low temperature wine zone controller
29. AINS AT A VERY STABLE TEMPERATURE LIGHT SWITCH AND BULB Your Single Door Refrigerator has an interior light that is illuminated when the door is opened The cabinet also comes standard with a manual light switch located next to the light for displaying your products through a glass door Always ensure that the manual switch is in the off position before closing a solid wood or stainless steel door If manual light switch is left on for an extended period of time it may increase the cabinet temperature especially at the top and cause the refrigeration system to run longer e SINGLE DOOR WINE COOLER OPERATION The Perlick Single Door Wine Cooler H1W comes equipped with a state of the art refrigeration system The compressor is of a variable speed variety which automatically changes speeds based on system conditions and load The cabinet is equipped with an adjustable digital temperature controller and LED display The controller can be adjusted through a range of 40 F to 68 F The controller has been factory set to modulate from 53 F to 57 F To properly determine product temperature see CHECKING PRODUCT TEMPERATURE on page 44 IMPORTANT NOTE ALWAYS ALLOW CABINET TO RUN FOR A MINIMUM OF 24 HOURS TO ALLOW TEMPERATURE STABILIZATION AFTER START UP BEFORE STORING PERISHABLE ITEMS This cabinet is a frost free model meaning the evaporator cooling coil automatically defrosts during off cycles The controller also has a
30. ANEL MUST NOT EXCEED 20 POUNDS IN WEIGHT 14 5 8 CS p DEE a X 1 4 7 q i N p pow MT 7 i 1734 678 H NS HINGE HOLE DETAIL 678 33 8 1 it 934 lo 934 J 29 1164 gt 1 1 1 Ta ILLUSTRATION 8 GLASS WOOD OVERLAY PANEL WARNING GLASS WOOD OVERLAY PANEL MUST NOT EXCEED 10 POUNDS IN WEIGHT 2416 AI Lu SECTION FF T 1 ww l 117182 m 23 82 m E 1458 4 pe Lom p B 1 171322 4 LH 2 1 23192 1 17 32 678 E UY F F H mur 678 1 11 3 4 1 1z ue X 1 2 DEEP nisl 33g 2 un 214 i iu 1 338 93 4 zi 9 34 L 117 32 SECTION E E 29 17 64 1 2 HINGE HOLE DETAIL 13 32 m Ei NS R5 32 www bringperlickhome com 16 ILLUSTRATION 9 SOLID WOOD DRAWER OVERLAY PANEL WARNING THE SOLID WOOD DRAWER OVERLAY PANEL MUST NOT EXCEED 10 POUNDS IN WEIGHT 11 3 4 1 8 X 1 2 DEEP 33 8 23 1 2 3 p STORAGE CAPABILITES IMPORTANT NOTE I
31. ATURE NOT PRODUCT TEMPERATURE UNDER THESE CONDITIONS AN 8 F AIR TEMPERATURE SWING DOES NOT CHANGE THE ACTUAL PRODUCT TEMPERATURE PRODUCT TEMPERATURE REMAINS AT A VERY STABLE TEMPERATURE LIGHT SWITCH AND BULB Your Single Door Freezer has an interior light that is illuminated when the door is opened The cabinet also comes standard with a manual light switch located next to the light Always ensure that the manual switch is in the off position before closing the door If manual light switch is left on for an extended period of time it may increase the cabinet temperature especially at the top and cause the refrigeration system to run longer e SINGLE DOOR REFRIGERATOR OPERATION The Perlick Single Door Refrigerator H1R comes equipped with a state of the art refrigeration system The compressor is of a variable speed variety which automatically changes speeds based on system conditions and load The cabinet is equipped with an adjustable digital temperature controller and LED display The controller can be adjusted through a range of 30 F to 42 F The controller has been factory set to modulate from 34 F to 40 F To properly determine product temperature see CHECKING PRODUCT TEMPERATURE on page 44 IMPORTANT NOTE ALWAYS ALLOW CABINET TO RUN FOR A MINIMUM OF 24 HOURS TO ALLOW TEMPERATURE STABILIZATION AFTER START UP BEFORE STORING PERISHABLE ITEMS This cabinet is a frost free model meaning the evaporator coo
32. E SET POINTS AND RANGES Range Range Single Door Freezer H1F Single Door Refrigerator Single Door Wine Cooler H1W Two Door Freezer Refrigerator H2FR Freezer Section Refrigerator Section Two Door All Refrigeration H2RO Two Door All Wine Cooler H2WO Two Door Refrigerator Wine Cooler H2RW Refrigerator Section Wine Cooler Section Two Door All Wine Cooler H2WW Wine Cooler Section 1 Wine Cooler Section 2 H3FRO Freezer Section Three Door Freezer Refrigerator Refrigerator Section O F 38 F 55 F O F 38 F 38 F 55 F 38 F 55 F 55 F 65 F O F 38 F Three Door Freezer Refrigerator Wine Cooler H3FRW Freezer Section Refrigerator Section Wine Cooler Section Three Door All Refrigerator H3ROO Three Door Wine Cooler H3 WOO O F 38 F 55 F 38 F 55 F Three Door Refrigerators Refrigerator Wine Cooler H3ROW Refrigerator Section Wine Cooler Section 55 F 38 F Range 50 F to 65 F Three Door Refrigerator Wine Cooler Wine Cooler H3RWO Refrigerator Section Wine Cooler Section Three Door Refrigerator Wine Cooler Wine Cooler Refrigerator Section Wine Cooler Section Wine Cooler Section 2 Three Door Wine Cooler H3WOW Wine Cooler Section Wine Cooler Section 2 Three Door Wine Cooler H3WWO Wine Cooler Section 1 Wine Cooler Section 2 Three Door All Wine H3WWW Wine Cooler Section 1
33. ERATURE REMAINS AT A VERY STABLE TEMPERATURE LIGHT SWITCH AND BULB Your Three Door Multi Zone Wine Cooler has three interior lights that are illuminated when each respective door is opened The cabinet also comes standard with manual light switches located next to each light for displaying your products through a glass door If manual light switch is left on for an extended period of time it may increase the cabinet temperature and in turn product temperature especially in close proximity to the light at the top and cause the refrigeration system to run longer e THREE DOOR TWO ZONE WINE COOLER OPERATION The Perlick Three Door Two Zone Wine Cooler H3WOW H3WWO comes equipped with a state of the art refrigeration system The compressor is of a variable speed variety which automatically changes speeds based on system conditions and load The cabinet is equipped with two adjustable digital temperature controllers and LED displays The low temperature wine zone controller located above the left door can be adjusted through a range of 42 F to 53 F The low temperature wine zone controller has been factory set to modulate from 53 F to 57 F The high temperature wine zone controller located above the center or right door dependent on the model can be adjusted through a range of 52 F to 65 F The high temperature wine zone controller has been factory set to modulate from 64 F to 66 F To properly determine product tempe
34. HE LOUVERED Check interior door openings inside the cabinet to ensure the cabinet is level Re install all shelving and drawers Take extreme care to insert sliding shelving and sliding drawers squarely into slide brackets and proper slide bracket grooves When sliding shelving and drawers are installed properly a click should be heard from both slide bracket retaining clips and should slide smoothly in the tracks When sliding shelving or drawers are pulled out to full extension a stop is activated to prevent additional pull out CAUTION IMPROPER SHELVING OR DRAWER INSTALLATION MAY NOT ACTUATE SLIDE STOP MECHANISM TOE PLATE INSTALLATION When the unit is secured in place install the louvered toe plate Using included fasteners secure the louvered toe plate to the cabinet flush with the floor Refer to TOE PLATE INSTALLATION ILLUSTRATION below Large slot allows for adjusting TOEPLATE to be flush with floor after leg levelers are put into desired position SECTIONS OF THE TOE PLATE MUST NOT BE COVERED OR OBSTRUCTED SO AS TO PREVENT PROPER AIR CIRCULATION www bringperlickhome com DOOR REVERSING All Perlick Residential Refrigerated Cabinets come equipped with field reversible left or right hand opening door capabilities Refer to DOOR REVERSING ILLUSTRATIONS on pages 13 14 To reverse the opening of the door remove the top pivot pin from the upper cabinet hinge bracket Pull the top pivot pin out of
35. HESE CONDITIONS A 4 F AIR TEMPERATURE SWING DOES NOT CHANGE THE ACTUAL PRODUCT TEMPERATURE PRODUCT TEMPERATURE REMAINS AT A VERY STABLE TEMPERATURE LIGHT SWITCH AND BULB Your Single Door Wine Cooler has an interior light that is illuminated when the door is opened The cabinet also comes standard with a manual light switch located next to the light for displaying your products through a glass door If manual light switch is left on for an extended period of time it may increase the cabinet temperature and in turn product temperature especially in close proximity to the light at the top and cause the refrigeration system to run longer OPERATION TWO DOOR TWO DOOR FREEZER REFRIGERATOR OPERATION The Perlick Two Door Freezer Refrigerator H2FR comes equipped with a state of the art refrigeration system The compressor is of a variable speed variety which automatically changes speeds based on system conditions and load The cabinet is equipped with two adjustable digital temperature controllers and LED displays The freezer controller can be adjusted through a range of 10 F to 10 F The freezer controller has been factory set to modulate from 3 F to 5 F The refrigerator controller can be adjusted through a range of 30 F to 42 F The refrigerator controller has been factory set to modulate from 37 F to 39 F To properly determine product temperature see CHECKING PRODUCT TEMPERATURE page 44 I
36. ICATIONS INSTALLING MULTI ZONE UNITS OUTDOORS WILL VOID THE WARRANTY This cabinet is a frost free model meaning the evaporator cooling coil automatically defrosts on demand at predetermined intervals The controller also has a manual defrost soft button on the front panel signified by a melting snowflake If depressed it will automatically put the system into a defrost cycle PROPER PRODUCT STORAGE Store product as desired in the freezer and refrigerator The wine cooler zone will accommodate 48 bottles of wine Specially designed full extension wine racks allow for proper horizontal storage of the wine The cork remains moist which keeps air from entering the bottle Do not block internal louvers or fan guard openings as this will decrease operating performance CONTROL SETTINGS The cabinet is shipped with the controllers turned ON To turn the refrigeration system OFF or ON press the blue soft button on the front face of the freezer controller if the controller is turned off with power applied to the cabinet the LED display will read OFF when turned on it will read a temperature The freezer controller is on the top front face of the cabinet above the left door and is equipped with a tinted see through lens which opens by pulling out on the bottom of the lens and rotating upwards Always ensure lens cover is closed before closing door to avoid damage to the controller or lens The refrigerator control looks and responds i
37. MINIMUM OF 24 HOURS TO ALLOW TEMPERATURE STABILIZATION AFTER START UP BEFORE STORING PERISHABLE ITEMS IMPORTANT NOTE PERLCK S MULTI ZONE UNITS ARE NOT DESIGNED FOR OUTDOOR APPLICATIONS INSTALLING MULTI ZONE UNITS OUTDOORS WILL VOID THE WARRANTY www bringperlickhome com 33 This cabinet is a frost free model meaning the evaporator cooling coil automatically defrosts on demand at predetermined intervals The controller also has a manual defrost soft button on the front panel signified by a melting snowflake If depressed it will automatically put the system into a defrost cycle PROPER PRODUCT STORAGE Store product as desired in the refrigerator The low temperature wine cooler zone will accommodate 48 bottles of wine The high temperature wine cooler zone will accommodate 48 bottles of wine Specially designed full extension wine racks allow for proper horizontal storage of the wine The cork remains moist which keeps air from entering the bottle Do not block internal louvers or fan guard openings as this will decrease operating performance CONTROL SETTINGS The cabinet is shipped with the controllers turned ON To turn the refrigeration system OFF or ON press the blue soft button on the front face of the freezer controller if the controller is turned off with power applied to the cabinet the LED display will read OFF when turned on it will read a temperature The freezer controller is located on th
38. MPORTANT NOTE ALWAYS ALLOW CABINET TO RUN FOR A MINIMUM OF 24 HOURS TO ALLOW TEMPERATURE STABILIZATION AFTER START UP BEFORE STORING PERISHABLE ITEMS IMPORTANT NOTE PERLCK S MULTI ZONE UNITS ARE NOT DESIGNED FOR OUTDOOR APPLICATIONS INSTALLING MULTI ZONE UNITS OUTDOORS WILL VOID THE WARRANTY This cabinet is a frost free model meaning the evaporator cooling coil automatically defrosts on demand at predetermined intervals The controller also has a manual defrost soft button on the front panel signified by a melting snowflake If depressed it will automatically put the system into a defrost cycle PROPER PRODUCT STORAGE Store product as desired Do not block internal louvers or fan guard openings as this will decrease operating performance CONTROL SETTINGS The cabinet is shipped with the controllers turned ON To turn the refrigeration system OFF or ON press the blue soft button on the front face of the freezer controller if the controller is turned off with power applied to the cabinet the LED display will read OFF when turned on it will read a temperature The controller is located on the top front face of the cabinet above the left door and is equipped with a tinted see through lens which opens by pulling out on the bottom of the lens and rotating upwards Always ensure lens cover is closed before closing door to avoid damage to the controller or lens The refrigerator control looks and responds identical to the fre
39. NTERIOR LOUVER OPENINGS AND FAN GUARD OPENINGS SHOULD NEVER BE OBSTRUCTED TO ACHIEVE MAXIMUM PERFORMANCE Two types of shelving are available for freezer and refrigerator compartments cantilever and full extension pullout shelves The cantilever or full extension pullout wire formed shelving comes with a durable black vinyl coated finish impermeable to rust and corrosion with side rails to prevent container tip over The full extension allows for easy product loading removal as well as visual inspection One fixed storage bottom step wire formed shelf with the same durable finish comes standard with each cabinet One type of shelving is available for wine cooler compartments full extension wine racks The full extension wire formed wine racks come with the same durable black vinyl coated finish and allow for full extension for easy bottle loading removal and visual inspection The fixed storage wire formed wine rack is coated with the same durable black vinyl coated finish and is sized to hold any size of wine bottle All wine rack spacing has been designed to optimize flexibility in storage of various sized wine bottles SINGLE DOOR FREEZER amp SINGLE DOOR REFRIGERATOR The single door freezer H1F and the single door refrigerator H1R come standard with either a single black vinyl coated cantilever or full extension pullout shelf and a bottom step shelf One additional black vinyl coated cantilever or pullout shelf can be us
40. O ALLOW TEMPERATURE STABILIZATION AFTER START UP BEFORE STORING PERISHABLE ITEMS This cabinet is a frost free model meaning the evaporator cooling coil automatically defrosts on demand at predetermined intervals The controller also has a manual defrost soft button on the front panel signified by a melting snowflake If depressed it will automatically put the system into a defrost cycle PROPER PRODUCT STORAGE Install items as desired Do not block internal louvers or fan guard openings as this will decrease operating performance CONTROL SETTINGS The cabinet is shipped with the controller turned ON To turn the cabinet OFF or ON press the blue soft button on the front face of the controller if the controller is turned off with power applied to the cabinet the LED display will read OFF when turned on it will read a temperature The controller is located on the top front face of the cabinet and is equipped with a tinted see through lens which opens by pulling out on the bottom of the lens and rotating upwards Always ensure lens cover is closed before closing door to avoid damage to the controller or lens The electronic control comes preset for a product temperature of approximately O F with a product temperature adjustability range of 10 F to 5 F To change temperature controller settings see section TEMPERATURE CONTROLLER ADJUSTMENTS on page 42 IMPORTANT NOTE THE LED DISPLAY IS READING ACTUAL AIR TEMPER
41. OOR ALL REFRIGERATOR OPERATION The Perlick Two Door All Refrigerator H2RO comes equipped with a state of the art refrigeration system The compressor is of a variable speed variety which automatically changes speeds based on system conditions and load The cabinet is equipped with an adjustable digital temperature controller and LED display The controller can be adjusted through a range of 30 F to 42 F The refrigerator controller has been factory set to modulate from 34 F to 40 F To properly determine product temperature see CHECKING PRODUCT TEMPERATURE on page 44 IMPORTANT NOTE ALWAYS ALLOW CABINET TO RUN FOR A MINIMUM OF 24 HOURS TO ALLOW TEMPERATURE STABILIZATION AFTER START UP BEFORE STORING PERISHABLE ITEMS This cabinet is a frost free model meaning the evaporator cooling coil automatically defrosts during off cycles The controller also has a manual defrost soft button on the front panel signified by a melting snowflake which has been disabled on this model PROPER PRODUCT STORAGE Store product as desired Do not block internal louvers or fan guard openings as this will decrease operating performance CONTROL SETTINGS The cabinet is shipped with the controllers turned ON To turn the refrigeration system OFF or ON press the blue soft button on the front face of the controller if the controller is turned off with power applied to the cabinet the LED display will read OFF when turned on it wil
42. YOUT PART 63740 0 375 n 4 4 H1 1 2 20 7 8 23 9 16 15 16 7 16 1 15 16 22 3 4 22 3 16 SS DOOR 24 5 8 WOOD DOOR y I b J t www bringperlickhome com ILLUSTRATION 4 THREE DOOR ANTI TIP LAYOUT PART 63740 1 1 4 0 375 20 7 8 23 9 16 115 16 a 1 2 2i 2 MEE REN 71 14 7 16 1 Weng 1 ll hse 1 22 3 4 24 3 16 SS DOOR 24 5 8 WOOD DOOR e oes U INSTALLING WARNING IMPORTANT NOTE If installing on a concrete floor concrete fasteners are required and not included with the anti tip kit CAUTION ANY FINISHED FLOORING SHOULD BE PROTECTED WITH APPROPRIATE MATERIAL TO AVOID DAMAGE FROM MOVING THE UNIT IF FOR ANY REASON THE UNIT HAS BEEN LAID ON ITS BACK OR SIDES YOU MUST ALLOW THE UNIT TO STAND UPRIGHT FOR A MINIMUM OF 24 HOURS BEFORE CONNECTING POWER Re install the doors by removing the upper pivot pin completely sliding the door onto the lower pivot pin and re installing the upper pivot pin and fastening tightly Before moving the unit make sure the door is secured to the cabinet tape may be required to hold the doors closed
43. ad The cabinet is equipped with two adjustable digital temperature controllers and LED displays The refrigerator zone controller located above the left door can be adjusted through a range of 33 F to 48 F The refrigerator zone controller has been factory set to modulate from 34 F to 40 F The wine cooler zone controller located above the right door can be adjusted through a range of 50 F to 60 F The wine cooler zone controller has been factory set to modulate from 54 F to 56 F To properly determine product temperature see CHECKING PRODUCT TEMPERATURE on page 44 www bringperlickhome com 26 IMPORTANT NOTE ALWAYS ALLOW CABINET TO RUN FOR A MINIMUM OF 24 HOURS TO ALLOW TEMPERATURE STABILIZATION AFTER START UP BEFORE STORING PERISHABLE ITEMS IMPORTANT NOTE PERLCK S MULTI ZONE UNITS ARE NOT DESIGNED FOR OUTDOOR APPLICATIONS INSTALLING MULTI ZONE UNITS OUTDOORS WILL VOID THE WARRANTY This cabinet is a frost free model meaning the evaporator cooling coil automatically defrosts during off cycles The controller also has a manual defrost soft button on the front panel signified by a melting snowflake which has been disabled on this model PROPER PRODUCT STORAGE The refrigerator can be filled as desired The wine cooler zone will accommodate 48 bottles of wine Specially designed full extension wine racks allow for proper horizontal storage of the wine The cork remains moist which keeps air
44. arts are not returned for inspection if so required by the Perlick Corporation To receive parts and or service and the name of the nearest Perlick authorized service representative contact your Perlick dealer distributor or Perlick Corporation s Technical Service Department 8300 West Good Hope Road Milwaukee Wisconsin 53223 call 800 558 5592 E mail us at warrantyserv perlick com or visit our web www bringperlickhome com This limited warranty is in lieu of any other warranty expressed or implied including but not limited to any implied warranty of merchantability or fitness for a particular purpose provided however that to the extent required by law implied warranties are included but do not extend beyond the duration of the express warranty first set above Perlick s sole liability and your exclusive remedy under this warranty are set forth in the initial paragraph above Perlick Corporation shall have no liability whatsoever for any incidental consequential or special damages arising from the sale use or installation of the product or from any other causes whatsoever whether based on warranty expressed or implied or otherwise based on contract tort or any other theory of liability Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations may not apply to you This warranty gives you specific legal rights and you ma
45. binets are pre set in order to achieve the recommended temperature range when installed in a 70 F ambient room temperature Factors which affect the internal temperatures of the refrigerated cabinet include Temperature setting Room temperature where installed Number of times the door is opened and closed Length of time the door is left open Adjacent compartment temperatures Style of door installed Door gasket sealing and condition Amount of time the internal light is illuminated Installation in direct sun light or near a heat source 9 9 LIGHT BULB REPLACEMENT To replace a defective or burnt out light bulb simply remove the glass lens by pulling down unscrew the bulb counterclockwise and replace with an identical 25 Watt bulb or smaller Perlick Replacement Bulb Number 63716 1 MAINTENANCE CLEANING To clean stainless steel exterior or interior surfaces use a soft non abrasive stainless steel cleaner to wipe down the these surfaces If you have difficulty finding a good cleaner try Signature Polish from Signature Limited Laboratory P O Box 13436 Dayton Ohio 45413 0436 or call toll free at 877 376 5474 Glass door panels can be cleaned using any standard glass cleaner available on the market today To clean interior and exterior non metallic surfaces and removable parts wash with a mild solution of soap and lukewarm water with a little baking soda Rinse and dry thoroughly Av
46. cabinet door to operate properly the door must open a minimum of 100 Use a minimum 5 3 4 inch filler in corner installations to assure a 100 door opening Allow enough clearance in front of the unit for full door swing shelf pull out or drawer pull out IMPORTANT NOTE Make sure the floor under the unit is level with the surrounding finished floor Protect a finished floor with plywood cardboard or some other suitable material before moving the cabinet across it Failure to do this may result in damage to your flooring PREPARING ELECTRICAL CONNECTIONS 115 volt 60Hz 15 amp circuit breaker and electrical supply are required A separate circuit is required for each Perlick Refrigerated Cabinet installed Follow the National Electrical Code and local codes and ordinances when installing the receptacle All Perlick Refrigerated Cabinets come equipped with a NEMA 5 15P 90 plug with a minimum of 5 feet of cord extending beyond the rear of the cabinet Refer to Illustration 1 for exact power cord exit location of your particular model The electrical outlet must be flush with or recessed into the back wall IMPORTANT NOTE Never use an extension cord to extend the power cord to the electrical receptacle DANGER ELECTROCUTION HAZARD ELECTRICAL GROUNDING REQUIRED THIS APPLIANCE IS EQUIPPED WITH A THREE PRONG GROUNDING POLARIZED PLUG FOR YOUR PROTECTION AGAINST POSSIBLE SHOCK HAZARDS NEVER REMOVE THE ROUND
47. d of time it may increase the cabinet temperature especially in close proximity to the light at the top and cause the refrigeration system to run longer THREE DOOR ALL REFRIGERATOR OPERATION The Perlick Three Door All Refrigerator H3ROO comes equipped with a state of the art refrigeration system The compressor is of a variable speed variety which automatically changes speeds based on system conditions and load The cabinet is equipped with an www bringperlickhome com 29 adjustable digital temperature controller and LED display The controller can be adjusted through a range of 30 F to 42 F The refrigerator controller has been factory set to modulate from 34 F to 40 F To properly determine product temperature see CHECKING PRODUCT TEMPERATURE on page 44 IMPORTANT NOTE ALWAYS ALLOW CABINET TO RUN FOR A MINIMUM OF 24 HOURS TO ALLOW TEMPERATURE STABILIZATION AFTER START UP BEFORE STORING PERISHABLE ITEMS This cabinet is a frost free model meaning the evaporator cooling coil automatically defrosts during off cycles The controller also has a manual defrost soft button on the front panel signified by a melting snowflake which has been disabled on this model PROPER PRODUCT STORAGE Store product as desired Do not block internal louvers or fan guard openings as this will decrease operating performance CONTROL SETTINGS The cabinet is shipped with the controller turned ON To turn
48. dentical to the freezer control with the exception that it only controls the cooling system for the refrigerator zone and is located above the center door The freezer electronic control comes preset for a product temperature of approximately O F with a product temperature adjustability range of 5 F to 5 F The refrigerator electronic control comes preset for a product temperature of approximately 38 F with a product temperature adjustability range of 33 F to 42 F The wine cooler electronic control comes preset for a product temperature of approximately 55 F with a product temperature adjustability range of 50 F to 60 F To change temperature controller settings see section TEMPERATURE CONTROLLER ADJUSTMENTS on page 42 IMPORTANT NOTE THE LED DISPLAY IS READING ACTUAL AIR TEMPERATURE NOT PRODUCT TEMPERATURE UNDER THESE CONDITIONS AN 8 F AIR TEMPERATURE SWING IN THE FREEZER COMPARTMENT AND A 2 F AIR TEMPERATURE SWING IN THE REFRIGERATOR OR WINE COOLER COMPARTMENT DOES NOT CHANGE THE ACTUAL PRODUCT TEMPERATURE PRODUCT TEMPERATURE REMAINS AT A VERY STABLE TEMPERATURE LIGHT SWITCH AND BULB Your Three Door Freezer Refrigerator Wine Cooler has three interior lights that are illuminated when each respective door is opened The cabinet also comes standard with a manual light switches located next to each light for displaying your products through a glass door If manual light switch is left on for an extended perio
49. door hinge bracket and remove the door by tilting forward and lifting off bottom hinge pin Re install pivot pin in top hinge Remove cabinet hinge screw hole plugs 8 each top and bottom from new hinge location Do not discard Remove the bottom cabinet hinge bracket 3 screws Remove lower cabinet hinge bracket 3 screws Remove door closer insert from the lower cabinet hinge bracket and install on new bottom hinge bracket old top hinge bracket Install new bottom cabinet hinge bracket at new bottom hinge location Install new top cabinet hinge bracket at new top hinge location Remove upper and lower door hinge brackets from door screws each Remove door closer insert from lower door hinge bracket and install on new lower door hinge bracket old top door hinge bracket Rotate the door 180 so handle is on new opening side Old bottom of door is new top of door Install new lower door hinge bracket to bottom of door 3 screws Install new upper door hinge bracket to top of door 3 screws Remove top pivot pin from the upper cabinet hinge bracket To re install the door slide lower door hinge bracket onto lower pivot pin Tilt top of door into position aligned with top cabinet hinge bracket and install top pivot pin tighten securely Install cabinet hinge screw hole plugs removed earlier in open hinge holes 3 each top and bottom www bringperlickhome com 11 ILLUSTRATION 6 DOOR SWING REVERSAL PROCEDURE
50. e banding touches the cabinet WARNING A MINIMUM OF TWO PEOPLE SHOULD LIFT THE CABINET OFF THE WOOD BASE LARGER CABINETS MAY REQUIRE ADDITIONAL HELPERS TO REMOVE FROM THE WOOD SHIPPING BASE Carefully move cabinet to installation opening Place in front of opening ANTI TIP OVER INSTALLATION WARNING TO PREVENT THE UNIT FROM TIPPING FORWARD IF LOADED BOTTLE RACKS LOADED PULLOUT SHELVES OR DRAWERS ARE PULLED OUT AT ONE TIME AND TO PROVIDE A STABLE INSTALLATION THE UNIT MUST BE SECURED IN PLACE WITH AN ANTI TIP DEVICE A set of metal anti tip brackets and installation screws 10 X wood screw are supplied with the unit This device should be attached to the floor towards the back of the appliance each bracket located to catch each rear leveling leg when inserted into the opening The anti tip brackets must catch each of the feet to have a stable and safe installation Some installation sites might need to be modified to provide a secure surface for attaching the bracket Refer to Illustration 2 3 or 4 below for anti tip mounting bracket locations www bringperlickhome com ILLUSTRATION 2 SINGLE DOOR LAYOUT DIA 0 375 PART 63740 N 4e 4 REF 112 qp CABINET FRONT 7 16 1 DETAIL 22 3 4 24 3 16 SS DOOR 24 5 8 WOOD DOOR 23 7 8 ILLUSTRATION 3 TWO DOOR ANTI TIP LA
51. e com Slide the cabinet into position making sure the rear cabinet leveling legs slide under the anti tip devices Push the cabinet into the opening until the bottom front edge of the cabinet is flush with the surrounding cabinetry or the leveling legs are tight with the anti tip devices Refer to ANTI TIP ILLUSTRATIONS on pages 8 9 for details The rear cabinet leveling legs should be held between the anti tip device and the floor To finish the leveling of the cabinet shim the front of the cabinet so the front face of the cabinet is flush with the surrounding cabinetry Adjust the front leveling legs to support the cabinet at the shimmed height Adjust legs by turning counterclockwise to raise the unit and clockwise to lower the unit using an adjustable wrench or pliers Countertop should be resting on top of cabinet IMPORTANT NOTE If countertop is not resting on entire cabinet top shimming of the countertop should be performed to prevent damage to the countertop CAUTION CARE SHOULD BE TAKEN TO PREVENT DAMAGE TO THE REFRIGERATED CABINET AND COUNTERTOP BY NEVER PLACING HEAVY OBJECTS ON TOP OF THE COUNTERTOP DIRECTLY ABOVE THE APPLIANCE ILLUSTRATION 5 TOE PLATE INSTALLATION PAN HEAD screws secure TOE PLATE to the cabinet Lastrow of louvers removed from view for clarification CAUTION THE LOUVERED TOE PLATE MUST BE REMOVABLE FOR SERVICING THE FLOOR CANNOT INTERFERE WITH REMOVAL T
52. e date of your Perlick product and your dealer s name address and telephone number MODELNUMBER SERIAL NUMBER PURCHASE DATE DEALER NAME amp ADDRESS DEALER TELEPHONE www bringperlickhome com TABLE OF CONTENTS INTRODUCTIONS rote te 1 PLEASE RECORD YOUR MODEL S INFORMATION 1 WARRANTY REGISTRATION 1 TABLE OF CONTENT S eintreten hn ete ea Riera 2 GENERAL 8 00 3 INSTALLATION 4 15 ILLUSTRATION 1 INSTALLATION SPECIFICATIONS 4 PREPARING THE SPACE sese 5 PREPARING ELECTRICAL 8 5 UNPACKING AND 6 ANTI TIP OVER 6 ILLUSTRATION 2 SINGLE DOOR ANTI TIP LAYOUT 7 ILLUSTRATION 3 TWO DOOR ANTI TIP LAYOUT 7 ILLUSTRATION 4 THREE DOOR ANTI TIP LAYOUT 8 INSTALLING RE 9 PLATE 9 ILLUSTRATION 5 TOE PLATE INSTALLATION 10 DOOR ananpi ioia 12 ILLUSTRATION 6 DOOR SWING REVERSAL PROCEDURE 13 DOOR OPTIONS lial 14 INSTALLATION OF WOOD
53. e top front face of the cabinet above the left door and is equipped with a tinted see through lens which opens by pulling out on the bottom of the lens and rotating upwards Always ensure lens cover is closed before closing door to avoid damage to the controller or lens The refrigerator control looks and responds identical to the freezer control with the exception that it only controls the cooling system for the refrigerator zone and is located above the center door The refrigerator electronic control comes preset for a product temperature of approximately 38 F with a product temperature adjustability range of 33 F to 42 F The low temperature wine cooler electronic control comes preset for a product temperature of approximately 55 F with a product temperature adjustability range of 45 F to 56 F The high temperature wine cooler electronic control comes preset for a product temperature of approximately 65 F with a product temperature adjustability range of 55 F to 68 F To change temperature controller settings see section TEMPERATURE CONTROLLER ADJUSTMENTS on page 42 IMPORTANT NOTE THE LED DISPLAY 15 READING ACTUAL AIR TEMPERATURE NOT PRODUCT TEMPERATURE UNDER THESE CONDITIONS A 4 F AIR TEMPERATURE SWING IN THE REFRIGERATOR COMPARTMENT AND A 2 F AIR TEMPERATURE SWING IN THE WINE COOLER COMPARTMENT DOES NOT CHANGE THE ACTUAL PRODUCT TEMPERATURE PRODUCT TEMPERATURE REMAINS AT A VERY STABLE TEMPERATURE LIGHT
54. each light for displaying your products through a glass door If manual light switch is left on for an extended period of time it may increase the cabinet temperature and in turn product temperature especially in close proximity to the light at the top and cause the refrigeration system to run longer e THREE DOOR THREE ZONE WINE COOLER OPERATION The Perlick Three Door Multi Zone Wine Cooler H3WWW comes equipped with a state of the art refrigeration system The compressor is of a variable speed variety which automatically changes speeds based on system conditions and load The cabinet is equipped with three adjustable digital temperature controllers and LED displays The low temperature wine zone controller located above the left door can be adjusted through a range of 40 F to 46 F The low temperature wine zone controller has been factory set to modulate from 43 F to 47 F The medium temperature wine zone controller located above the center door can be adjusted through a range of 48 F to 58 F The medium temperature wine zone controller has been factory set to modulate from 54 F to 56 F The high temperature wine zone controller located above the right door can be adjusted through a range of 58 F to 65 F The high temperature wine zone controller has been factory set to modulate from 64 F to 66 F To properly determine product temperature see CHECKING PRODUCT TEMPERATURE on page 44 IMPORTANT NOTE ALWAYS ALLOW C
55. ecautions are not followed Once the unit is completely installed we suggest you keep this manual and purchasing documentation in a safe place for future reference Should problems occur refer to the troubleshooting section of this manual The information will help you quickly identify a problem and get it remedied In the event you require assistance please contact the dealer where you purchased your unit PLEASE RECORD YOUR MODEL S INFORMATION Whenever you call to request information or service you will need to know your model number and serial number You can find this information on the serial and identification plate located on the inside ceiling of your unit and on the warranty registration card WARRANTY REGISTRATION CARD The package containing this manual also includes your warranty registration information Warranty coverage begins on the date your Perlick Refrigerated Cabinet was originally purchased IMPORTANT NOTE Take a moment to read through the included warranty statement and complete and mail the Warranty Registration Card as soon as possible to validate the registration date An alternative method of completing the Warranty Registration can be accomplished online at www bringperlickhome com If you do not complete your Warranty Registration Card on line or return via U S mail Perlick will use the date of sale as the first date of warranty for your new Refrigerated Cabinet Please record the purchas
56. ed in these cabinets SINGLE DOOR WINE COOLER The single door wine cooler H1W comes standard with four full extension black vinyl coated wine racks capable of storing 32 total wine bottles standard magnum or half size bottles An additional fixed storage rack is nestled into the lower step for storage of an additional 10 wine bottles standard magnum or half size bottles www bringperlickhome com 17 TWO DOOR FREEZER REFRIGERATOR amp TWO DOOR ALL REFRIGERATOR The two door freezer refrigerator H2FR and the two door all refrigerator H2RO come standard with three black vinyl coated cantilever or pullout shelves and a bottom step shelf Up to two additional black vinyl coated cantilever or pullout shelves can be used in these cabinets TWO DOOR REFRIGERATOR WINE COOLER The two door refrigerator wine cooler H2RW comes standard with one black vinyl coated cantilever or pull out shelf a bottom step shelf and six full extension black vinyl coated wine racks capable of storing 48 total wine bottles standard magnum or half size bottles One additional black vinyl coated cantilever or pullout shelf can be used in this cabinet TWO DOOR ALL WINE COOLER The two door all wine cooler H2WW or H2WO comes standard with ten full extension black vinyl coated wine racks capable of storing 80 total wine bottles standard magnum or half size bottles An additional fixed storage rack is nestled into the
57. et temperature especially in close proximity to the light at the top and cause the refrigeration system to run longer THREE DOOR ALL WINE COOLER OPERATION The Perlick Three Door All Wine Cooler H3WOO comes equipped with a state of the art refrigeration system The compressor is of a variable speed variety which automatically changes speeds based on system conditions and load The cabinet is equipped with an adjustable digital temperature controller and LED display The controller can be adjusted through a range of 40 F to 65 F The wine cooler controller has been factory set to modulate from 53 F to 57 F To properly determine product temperature see CHECKING PRODUCT TEMPERATURE on page 44 IMPORTANT NOTE ALWAYS ALLOW CABINET TO RUN FOR A MINIMUM OF 24 HOURS TO ALLOW TEMPERATURE STABILIZATION AFTER START UP BEFORE STORING PERISHABLE ITEMS This cabinet is a frost free model meaning the evaporator cooling coil automatically defrosts during off cycles The controller also has a manual defrost soft button on the front panel signified by a melting snowflake which has been disabled on this model PROPER PRODUCT STORAGE This wine cooler will accommodate 138 bottles of wine Specially designed full extension wine racks allow for proper horizontal storage of the wine The cork remains moist which keeps air from entering the bottle Do not block internal louvers or fan guard openings as this will decrease operat
58. ezer control with the exception that it only controls the cooling system for the refrigerator zone and is located above the right door The freezer electronic control comes preset for a product temperature of approximately O F with a product temperature adjustability range of 10 F to 5 F The refrigerator electronic control comes preset for a product temperature of approximately 38 F with a product temperature adjustability range of 33 F to 42 F To change temperature controller settings see section TEMPERATURE CONTROLLER ADJUSTMENTS on page 42 www bringperlickhome com 23 IMPORTANT NOTE THE LED DISPLAY IS READING ACTUAL AIR TEMPERATURE NOT PRODUCT TEMPERATURE UNDER THESE CONDITIONS AN 8 F AIR TEMPERATURE SWING IN THE FREEZER COMPARTMENT AND A 2 F AIR TEMPERATURE SWING IN THE REFRIGERATOR COMPARTMENT DOES NOT CHANGE THE ACTUAL PRODUCT TEMPERATURE PRODUCT TEMPERATURE REMAINS AT A VERY STABLE TEMPERATURE LIGHT SWITCH AND BULB Your Two Door Freezer Refrigerator has two interior lights that are illuminated when the corresponding door is opened The cabinet also comes standard with manual light switches located next to each light for displaying your products through a glass door If manual light switch is left on for an extended period of time it may increase the cabinet temperature especially in close proximity to the light at the top and cause the refrigeration system to run longer TWO D
59. he Perlick Two Door All Wine Cooler H2WO comes equipped with a state of the art refrigeration system The compressor is of a variable speed variety which automatically changes speeds based on system conditions and load The cabinet is equipped with an adjustable digital temperature controller and LED display The controller can be adjusted through a range of 40 F to 65 F The refrigerator controller has been factory set to modulate from 53 F to 57 F To properly determine product temperature see CHECKING PRODUCT TEMPERATURE on page 44 IMPORTANT NOTE ALWAYS ALLOW CABINET TO RUN FOR A MINIMUM OF 24 HOURS TO ALLOW TEMPERATURE STABILIZATION AFTER START UP BEFORE STORING PERISHABLE ITEMS This cabinet is a frost free model meaning the evaporator cooling coil automatically defrosts during off cycles The controller also has a manual defrost soft button on the front panel signified by a melting snowflake which has been disabled on this model PROPER PRODUCT STORAGE This wine cooler will accommodate 90 bottles of wine Specially designed full extension wine racks allow for proper horizontal storage of the wine The cork remains moist which keeps air from entering the bottle Do not block internal louvers or fan guard openings as this will decrease operating performance CONTROL SETTINGS The cabinet is shipped with the controller turned ON To turn the refrigeration system OFF or ON press the blue soft button on the f
60. ightly away from the upper cabinet hinge Gently lift up on the door to remove the door from the lower pivot pin Set door aside in safe location to prevent damage Re install the upper pivot pin for safekeeping Refer to PROCEDURE FOR SWITCHING DIRECTION OF DOOR SWING pages 13 15 STEP 1 for Removal and Step 6 for Re hanging To remove cantilever shelving lift shelf upward and pull forward Set cantilever shelving aside for safekeeping To remove sliding shelving or sliding drawers pull shelf or drawer forward until completely extended Press on both release points on outside edge of shelf or drawer brackets and pull shelf or drawer completely out Continue until all shelving has been removed from the cabinet Set all drawers and shelving aside for safekeeping WARNING PULL ONLY ONE DRAWER OR SHELF OUT AT A TIME TO PREVENT POSSIBLE TIP OVER CAUTION SUPPORT SLIDING DRAWERS AND SLIDING SHELVING HORIZONTALLY AND PULL STRAIGHT OUT TO AVOID DAMAGE TO SLIDES Carefully lift cabinet off wood base and onto a hand truck s or dolly Ensure cabinet is balanced on transporting device Multi door cabinets have an offset center of gravity towards the left most door when facing the front of the cabinet due to the refrigeration system in and under the first door Secure the cabinet to the transporting device s using soft flexible strapping to prevent damage to exterior cabinet finish cover and protect cabinet with cloth material wher
61. ing performance www bringperlickhome com 30 CONTROL SETTINGS The cabinet is shipped with the controller turned ON To turn the refrigeration system OFF or ON press the blue soft button on the front face of the controller if the controller is turned off with power applied to the cabinet the LED display will read OFF when turned on it will read a temperature The controller is located on the top front face of the cabinet above the left door and is equipped with a tinted see through lens which opens by pulling out on the bottom of the lens and rotating upwards Always ensure lens cover is closed before closing door to avoid damage to the controller or lens The wine cooler electronic control comes preset for a product temperature of approximately 55 F with a product temperature adjustability range of 42 F to 68 F To change temperature controller settings see section TEMPERATURE CONTROLLER ADJUSTMENTS on page 42 IMPORTANT NOTE THE LED DISPLAY IS READING ACTUAL AIR TEMPERATURE NOT PRODUCT TEMPERATURE UNDER THESE CONDITIONS A 4 F AIR TEMPERATURE SWING IN THE WINE COOLER COMPARTMENT DOES NOT CHANGE THE ACTUAL PRODUCT TEMPERATURE PRODUCT TEMPERATURE REMAINS AT A VERY STABLE TEMPERATURE LIGHT SWITCH AND BULB Your Three Door All Wine Cooler has three interior lights that are illuminated when each respective door is opened The cabinet also comes standard with manual light switches located next to
62. ion s warranty covers all parts and labor to repair or replace any part of the product which proves to be defective in material and workmanship ADDITIONAL Third Through Sixth Year Limited Parts Only Warranty During the four years following expiration of the Two Year Warranty Perlick will supply replacement parts only for the hermetically sealed refrigeration system which consist of the compressor condenser drier connecting tubing evaporator and hot gas bypass valve TERMS The Perlick Warranty applies to products installed in the fifty United States the District of Columbia or the ten provinces of Canada All service provided by Perlick Corporation under the above warranty must be performed by authorized Perlick service representatives unless otherwise specified by Perlick Service will be provided in the home during normal business hours This warranty applies only to products installed for normal residential use it does not include adjusting the controls door reversal light bulb or cleaning the condenser This warranty is extended only to the original purchaser of the Perlick product The above warranty does not apply if e Failure of product was due to transportation Product was improperly installed misused abused operating with low voltage wiring not conforming electrical codes improperly maintained or modified e The original Bill of Sale delivery date or serial number cannot be verified e Defective p
63. is located on the top front face of the cabinet above the left door and is equipped with a tinted see through lens which opens by pulling out on the bottom of the lens and rotating upwards Always ensure lens cover is closed before closing door to avoid damage to the controller or lens The medium temperature wine zone controller appears identical except it controls this zones cooling system and is located above the center door The warm temperature wine zone controller appears identical except it controls this zones cooling system and is located above the right door The low temperature wine zone electronic control comes preset for a product temperature of approximately 45 F with a product temperature adjustability range of 44 F to 48 F The medium temperature wine zone electronic control comes preset for a product temperature of approximately 55 F with a product temperature adjustability range of 49 F to 56 F The high temperature wine zone electronic control comes preset for a product temperature of approximately 65 F with a product temperature adjustability range of 59 F to 66 F To change temperature controller settings see section TEMPERATURE CONTROLLER ADJUSTMENTS on page 42 IMPORTANT NOTE THE LED DISPLAY IS READING ACTUAL AIR TEMPERATURE NOT PRODUCT TEMPERATURE UNDER THESE CONDITIONS A 4 F OR 2 F AIR TEMPERATURE SWING IN THE WINE COOLER COMPARTMENT DOES NOT CHANGE THE ACTUAL PRODUCT TEMPERATURE PRODUCT TEMP
64. ithout at least one other person present Always secure doors shut prior to moving the unit _ 90 Area in which electrical outlet must be located 237 8 ie 13 1 16 same on both sides of unit 5 3 16 minimum clearance Top View sr Told 22 3 4 required if installing in a corner Single Door 5 3 4 for custom wood overlay door P minimum swing Max swing is 175 on single door and end cabinets on multi door units 25 Min Clearance for doo r swing 50 Area in which electrical outlet must be located 13 3 32 Same for Two and dd Three door units 1 View Two Door 50 Area in which electrical outlet must be located 71 7 8 View Three Door 9 150 swing 105 max swing on inner doors of for custom wood overlay a multi door unit doors www bringperlickhome com 47 7 8 PREPARING THE SPACE Make sure that the opening where the Perlick cabinet s is are to be installed is properly prepared Refer to Illustration 1 to ensure the space dimensions and electrical service are correct for the models to be installed CAUTION IF CABINET IS BEING INSTALLED UNDER A COUNTER TOP IT IS RECOMMENDED THAT THE COUNTER TOP BE SUPPORTED BY STRUCTURE OTHER THAN THE REFRIGERATED CABINET TO PREVENT DAMAGE TO THE COUNTER TOP IMPORTANT NOTE For a
65. k Corporation Customer Service Department 8300 W Good Hope Rd Milwaukee WI 53223 call 800 558 5592 or e mail us at warrantyserv perlick com www bringperlickhome com 41 380 MOSN3S LNANLYVdNOO QO31V439lHj3H 9 dSO YOLOW S3GIAG Z 40 IN3ALSVdWOO IN3ALMVdNOO HOLIMS LHO TIVONVA MS HOLIMS YOOd SOLON M3QIAIO 1H9 l1 MSO M3T10M1INOO W31SAS 33MH1 IN3AIEVdAOO 0 701MX 38O0Bd MOSN3S Z IN3AIMVdAOO QO31VH39lHj3M Z d 29 MOION AMVTIIXQv L NY MOION N3QIAIQ L W3G MSZ 1H9 1 2 1IN3AL1SVdAWO2 7Z LNSNLYVdNOO HOLIMS 1 911 TVnNVAA MS HOLIMS 8000 YOLOW 830110 1 0 50 M3110M1NO9 W31SAS OML IN3ALISVdWOO 20 101MX 3311081NO2 33183ANI 1V2l810313 MOSS3SdAOO L NI MOION 35530 02 1 42 GION31OS 1808430 SVD 10 59 38084 MOSN3S 1508430 d4Q 380Hd MOSN3S IN3ALINVdAOO Q31V939lHJ3H 1 459 YOLOW MOlVHOdVA3 1 53 LNSWLYVdNOO 1 LHOM HOLIMS IHON TWANVA 1 MS HOLIMS YOO YOLOW dVA3 ONY 1 9 1 50 S3TIOMINOO WALSAS NOILVM39IHA38 L0 7108MX ie b HMM ALHA y C LH9TT
66. l read a temperature The controller is located on the top front face of the cabinet above the left door and is equipped with a tinted see through lens which opens by pulling out on the bottom of the lens and rotating upwards Always ensure lens cover is closed before closing door to avoid damage to the controller or lens The refrigerator electronic control comes preset for a product temperature of approximately 38 F with a product temperature adjustability range of 33 F to 45 F To change temperature controller settings see section TEMPERATURE CONTROLLER ADJUSTMENTS on page 42 IMPORTANT NOTE THE LED DISPLAY IS READING ACTUAL AIR TEMPERATURE NOT PRODUCT TEMPERATURE UNDER THESE CONDITIONS A 6 F AIR TEMPERATURE SWING IN THE REFRIGERATOR COMPARTMENT DOES NOT CHANGE THE ACTUAL PRODUCT TEMPERATURE PRODUCT TEMPERATURE REMAINS AT A VERY STABLE TEMPERATURE LIGHT SWITCH AND BULB Your Two Door All Refrigerator has two interior lights that are illuminated when each corresponding door is opened The cabinet also comes standard with manual light switches located next to each light for displaying your products through a glass door If manual light switch is left on for an extended period of time it may increase the cabinet temperature especially in close proximity to the light at the top and cause the refrigeration system to run longer www bringperlickhome com 24 e TWO DOOR ALL WINE COOLER OPERATION T
67. lashing with FLASHING See above in parenthesis The defrost is enabled FLASHING Drip time in progress The fast freezing cycle is enabled Alarm signal Contact Service Representative immediately SE EER x x The light is on www bringperlickhome com 35 TEMPERATURE CONTROLLER ADJUSTMENTS POWER Each digital temperature controller and LED display comes equipped with a soft power button which turns the respective cooling system ON or OFF If when power is applied to the cabinet and the display reads OFF simply press the blue soft button once to turn the cooling system ON When the controller is ON it will display the current temperature reading DEFROST Controllers controlling a freezer section are programmed with an automatic defrosting cycle for the evaporator coil cooling coil During this cycle the display will read DEF Once the defrost cycle is complete it will return to a temperature reading in the display These controllers are also equipped with a soft defrost button on the front of the controller panel which is signified by a melting snowflake If depressed on a freezer section it will automatically put the system into a defrost cycle Upon completion of the cycle the controller will return to normal cooling mode Although this button is enabled it should not be necessary to use for additional defrost cycles Models which to do not require a programmed defrost cycle refrigerators and
68. ling coil automatically defrosts during off cycles The controller also has a manual defrost soft button on the front panel signified by a melting snowflake which is www bringperlickhome com 21 disabled for this model PROPER PRODUCT STORAGE Install items as desired Do not block internal louvers or fan guard openings as this will decrease operating performance CONTROL SETTINGS The cabinet is shipped with the controller turned ON To turn the cabinet OFF or ON press the blue soft button on the front face of the controller if the controller is turned off with power applied to the cabinet the LED display will read OFF when turned on it will read a temperature The controller is located on the top front face of the cabinet and is equipped with a tinted see through lens which opens by pulling out on the bottom of the lens and rotating upwards Always ensure lens cover is closed before closing door to avoid damage to the controller or lens The electronic control comes preset for a product temperature of approximately 38 F with a product temperature adjustability range of 33 F to 45 F To change temperature controller settings see section TEMPERATURE CONTROLLER ADJUSTMENTS on page 42 IMPORTANT NOTE THE LED DISPLAY IS READING ACTUAL AIR TEMPERATURE NOT PRODUCT TEMPERATURE UNDER THESE CONDITIONS A 6 F AIR TEMPERATURE SWING DOES NOT CHANGE THE ACTUAL PRODUCT TEMPERATURE PRODUCT TEMPERATURE REM
69. lower step of the first door for storage of an additional 10 wine bottles standard magnum or half size bottles If the cabinet is a multi zone wine cooler the first door can hold 42 total wine bottles while the second door can hold 48 total wine bottles THREE DOOR FREEZER REFRIGERATOR RE FRIGERATOR amp THREE DOOR ALL REFRIGERATOR The three door freezer refrigerator refrigerator H3FRO and the three door all refrigerator H3ROO come standard with five black vinyl coated cantilever or pullout shelves anda bottom step shelf Up to three additional black vinyl coated cantilever or pullout shelves can be used in these cabinets THREE DOOR REFRIGERATOR REFRIGERA TOR WINE COOLER The three door refrigerator refrigerator wine cooler HSROW comes standard with three black vinyl coated cantilever or pull out shelves a bottom step shelf and six full extension black vinyl coated wine racks capable of storing 48 total wine bottles standard magnum or half size bottles Up to two additional black coated cantilever or pullout shelves can be used in this cabinet THREE DOOR REFRIGERATOR WINE COOLER WINE COOLER The three door refrigerator wine cooler wine cooler HSRWO HSRWW comes standard with one black vinyl coated cantilever or pull out shelf a bottom step shelf and twelve full extension black vinyl coated wine racks capable of storing 96 total wine bottles standard magnum or half size bottles Up to one
70. mains in the beer from the fermentation process When the temperature of draft beer exceeds 50 a process of secondary fermentation may take place The beer faucet may exhibit a white colored substance yeast build up if not cleaned on a regular basis No 887 Perlick is committed to continuous improvement Therefore we reserve the right to change specifications without prior notice Beer Stone All beer contains calcium which is present from the grains used in the brewing process it is an important natural material in draft systems in that as it oxidizes it coats the internal parts of the beer lines and equipment This thin coat of beer stone helps prevent the beer from picking up strong metallic or plastic flavors as it flows through the system The beer stone will continue to build if the system is not cleaned properly or regularly and can cause drawing problems if it begins to flake off Beer stone is present if one can see a brownish color on the faucet or inner wall of the beer line or tobacco like flakes in the beer Cleaning the Cabinet Use a mild detergent and water to clean the inside and outside of the cabinet Dry thoroughly Never use a scouring pad or abrasive cleanser NOTE An industrial strength commercial cleaner can be used to clean the outside of painted cabinets Cleaning the Condenser Use a long handled stiff brush to clean the dirt from the front surface of the condenser Keeping the conden
71. mpletely Perlick is committed to continuous improvement Therefore we reserve the right to change specifications without prior notice CORPORATION Form No 22259 7 Rev 1 17 05 www bringperlickhome com 50 PURCHASE RECORD X CATALOG PATTERN NAME amp SIZE MATERIAL i i Oe TAG NOTED 43020A2 ROUGH WT PERLICK NO 40030 LOW PROFILE TAP To tap place bottom adapter in extended position align lug openings and insert into keg turning Clockwise to stop To open beer valve push down and turn Clockwise to second stop CAUTION UN DO NOT USE TO KEG Form 43020A2 REF REPLACES 43020A1 TOLERANCES UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES 2 DECIMAL DIMENSIONS 0625 PERLICK CORPORATION MILWAUKEE WI FULL SIZE MMS parr 8 TAG CHK D DATE FOR MK20 LOW PROFILE COUPLER NO 40030 MEI AME REV Baths THIS DOCUMENT PUBLICATION SOFTWARE DRAWING CONTAINS PROPRIETARY INFORMATION WHICH IS THE PROPERTY OF THE PERLICK CORP IT MAY NOT BE REPRODUCED OR TRANSMITTED IN ANY FORM 99 4 5 2 1 21 02 ELECTRONIC OR MECHANICAL INCLUDING PHOTOCOPYING RECORDING OR USED IN ANY INFORMATION PAD STORAGE TRANSMISSION OR RETRIEVAL SYSTEM WITHOUT WRITTEN PERMISSION FROM PERLICK CORP SHEET 2 OF 2 www bringperlickhome com 51
72. ned on it will read a temperature The low temperature wine zone controller is located on the top front face of the cabinet above the left door and is equipped with a tinted see through lens which opens by pulling out on the bottom of the lens and rotating upwards Always ensure lens cover is closed before closing door to avoid damage to the controller or lens The high temperature wine zone controller appears identical except it controls this zones cooling system and is located above the center or right door dependent on the model The low temperature wine zone electronic control comes preset for a product temperature of approximately 55 F with a product temperature adjustability range of 44 F to 56 F The high temperature wine zone electronic control comes preset for a product temperature of approximately 65 F with a product temperature adjustability range of 52 F to 68 F To change temperature controller settings see section TEMPERATURE CONTROLLER ADJUSTMENTS page 42 IMPORTANT NOTE THE LED DISPLAY IS READING ACTUAL AIR TEMPERATURE NOT PRODUCT TEMPERATURE UNDER THESE CONDITIONS A 4 F OR 2 F AIR TEMPERATURE SWING IN THE WINE COOLER COMPARTMENT DOES NOT CHANGE THE ACTUAL PRODUCT TEMPERATURE PRODUCT TEMPERATURE REMAINS AT A VERY STABLE TEMPERATURE LIGHT SWITCH AND BULB Your Three Door Two Zone Wine Cooler has three interior lights that are illuminated when each respective door is opened The cabinet also come
73. need product information e Contact your selling dealer e Inquire via the WEB at www bringperlickhome com e 800 558 5592 for factory assistance for information for planning installation or product information e Write to Perlick Corporation Customer Service Department 8300 W Good Hope Rd Milwaukee WI 53223 e or e mail us at warrantyserv perlick com You need product service e Check the model and serial number of your unit located on the label attached to the inside top of the cabinet Then call your Perlick Factory Authorized Service Center For the location of the Service Center in your area contact your dealer inquire via the WEB at www bringperlickhome com or write to Perlick Corporation Customer Service Department 8300 W Good Hope Rd Milwaukee WI 53223 call 800 558 5592 or e mail us at warrantyserv perlick com Mir need replacement parts or accessories Use only genuine Perlick replacement parts and accessories Genuine Perlick parts and accessories are designed to work correctly with Perlick products and offer superior service life The use of non Perlick parts can damage the unit and may void the warranty e Check the model and serial number of your unit located on the label attached to the inside top of the cabinet Then call your Perlick Factory Authorized Service Center For the location of the Service Center in your area contact your dealer inquire via the WEB at www bringperlickhome com or write to Perlic
74. nterior light e sthe bulb loose 5 the bulb burned out Light stays on when door is closed Manual ON OFF light switch is turned ON e 5 the door switch making contact with the door Noise during operation e Certain sounds are normal Soft sounds from the compressor fan motor and valves will be heard e During freezer defrost crackling is normal Controller display is flashing P1 e There is a thermostat probe failure Controller display is flashing P2 There is an evaporator probe failure Controller display is flashing HA The internal compartment temperature has exceeded the high temperature alarm preset value for over 30 minutes Check to ensure door is closed Check for door gasket seal Did you just install warm product Is the condenser clean Is the louvered toe plate obstructed Has the surrounding ambient temperature changed dramatically Is the interior light ON Controller display is flashing LA e internal compartment temperature has exceeded the low temperature alarm preset value for over 30 minutes e Check to ensure door is closed e Check for door gasket seal e Has the surrounding ambient temperature changed dramatically Controller display is flashing e The controller has a data or memory failure The refrigerated cabinet isn t running e 5 there electrical power to the unit e 15 your home circuit breaker or fuse on Is your ON OFF key pad
75. o CO2 oylinder W Secure oylinder in upright position whether in storage or in use Keep cylinder away from heat Rupture disc vents at 122 F maximum Ventilate room after high pressure gas leakage Check the last DOT test date on cylinder neck before filling If more than five years old the cylinder must be retested to DOT specifications Be sure CC2 cylinder outlet fitting is free of dust or dirt before attaching regulator Store CO2 cylinder and regulator assembly upright Allow only properly trained and experienced personnel to handle high pressure gas NEVER Connect cylinder directly to keg without regulator reducing valve Drop or throw regulator or CO2 cylinder Transport CO2 cylinder in a closed vehicle Apply oil to a regulator Shut off CO2 cylinder when not in use You will not save gas by doing so Allow untrained inexperienced personnel to handle high pressure gas One of the most common causes of dispensing problems is improper temperature Draft beer should be stored at a temperature between 32 and 38 At warmer temperatures beer will foam At temperatures lower than 30 F beer will freeze When beer freezes the alcohol in the beer may separate and cause the beer to be cloudy with an off taste HOW TEMPERATURE AFFECTS DRAFT BEER Zo o 28 30 32 34 Rev 1 17 05 Perlick is committed to continuous improvement Therefore we reserve
76. o not damage the wood overlay panel Countersink screw head s so when installed in the wood overlay panel the screw head s is are flush with the backside of the wood overlay panel CAUTION PROPER WOOD WORKING MATERIALS AND EQUIPMENT SHOULD BE USED TO AVOID DAMAGE OR ERRORS IN WORKMANSHIP Decorative wood panels should be attached to the factory supplied overlay doors using 10 X 1 wood screws passing through the doorframe from the rear into the overlay panel The factory supplied overlay doorframe is predrilled for ease of overlay panel installation IMPORTANT NOTE DO NOT OVER TIGHTEN WOOD OVERLAY ATTACHMENT SCREWS AS THIS MAY DAMAGE FACTORY SUPPLIED DOORFRAME With the cabinet secured in position open cabinet door and ensure wood overlay panel predrilled pilot fastening holes align with factory www bringperlickhome com 14 door frame predrilled holes Start inserting fasteners in four corners of the doorframe and fasten loosely Before proceeding with additional mounting fasteners check for overall wood overlay fit position and function Make minor adjustments as needed Upon satisfaction with appearance securely tighten existing screws Complete installation of wood overlay panel by installing the rest of the fasteners and completely tightening Check all screws for tightness www bringperlickhome com 15 ILLUSTRATION 7 SOLID WOOD OVERLAY PANEL WARNING SOLID WOOD OVERLAY P
77. oid getting water on lights controllers fan motors and unfinished wood wine rack faces CAUTION DO NOT USE ABRASIVE CLEANERS OR CLOTHS ON ANY OF THE INTERIOR OR EXTERIOR SURFACES OR REMOVABLE PARTS CONDENSER CLEANING WARNING FOR CLEANING THE CONDENSER AND OTHER ROUTINE MAINTENANCE SHUT OFF ELECTRICITY TO THE UNIT In all instances you should clean the condenser area every three months The condenser is located behind the louvered toe plate To clean the condenser remove the toe plate and use a soft bristle brush and vacuum to remove dust and lint Avoid damaging or crushing the condenser fins or tubing Upon completion re install the louvered toe plate CAUTION FAILURE TO CLEAN THE CONDENSER COULD RESULT IN TEMPERATURE LOSS OR MECHANICAL FAILURE OR DAMAGES CLEAN THIS AREA EVERY THREE MONTHS www bringperlickhome com 38 www bringperlickhome com 39 TROUBLESHOOTING BEFORE CALLING FOR SERVICE If the unit appears to be malfunctioning read through NORMAL OPERATION first If the problem persists check the TROUBLESHOOTING GUIDE Locate the problem in the guide and refer to the cause and its remedy before calling for service The problem could be something which can be solved without a service call GENERAL TROUBLESHOOTING DANGER ELECTROCUTION HAZARD NEVER ATTEMPT TO REPAIR OR PERFORM MAINTENANCE ON THE UNIT UNTIL THE MAIN ELECTRICAL POWER HAS BEEN DISCONNECTED No i
78. pproximately 55 F with a product temperature adjustability range of 40 F to 56 F The warm temperature wine zone electronic control comes preset for a product temperature of approximately 65 F with a product temperature adjustability range of 54 F to 68 F To change temperature controller settings see section TEMPERATURE CONTROLLER ADJUSTMENTS on page 42 IMPORTANT NOTE THE LED DISPLAY IS READING ACTUAL AIR TEMPERATURE NOT PRODUCT TEMPERATURE UNDER THESE CONDITIONS A 4 F AIR TEMPERATURE SWING IN THE WINE COOLER COMPARTMENT DOES NOT CHANGE THE ACTUAL PRODUCT TEMPERATURE PRODUCT TEMPERATURE REMAINS AT A VERY STABLE TEMPERATURE LIGHT SWITCH AND BULB Your Two Door Multi Zone Wine Cooler has two interior lights that are illuminated when each respective door is opened The cabinet also comes standard with manual light switches located next to each light for displaying your products through a glass door If manual light switch is left on for an extended period of time it may increase the cabinet temperature and in turn product temperature especially in close proximity to the light at the top and cause the refrigeration system to run longer e TWO DOOR REFRIGERATOR WINE COOLER OPERATION The Perlick Two Door Refrigerator Wine Cooler H2RW comes equipped with a state of the art refrigeration system The compressor is of a variable speed variety which automatically changes speeds based on system conditions and lo
79. rature see CHECKING PRODUCT TEMPERATURE page 44 IMPORTANT NOTE ALWAYS ALLOW CABINET TO RUN FOR A MINIMUM OF 24 HOURS TO ALLOW TEMPERATURE STABILIZATION AFTER START UP BEFORE STORING PERISHABLE ITEMS IMPORTANT NOTE PERLCK S MULTI ZONE UNITS ARE NOT DESIGNED FOR OUTDOOR APPLICATIONS INSTALLING MULTI ZONE UNITS OUTDOORS WILL VOID THE WARRANTY This cabinet is a frost free model meaning the evaporator cooling coil automatically defrosts during off cycles The controller also has a manual defrost soft button on the front panel signified by a melting snowflake which has been disabled on this model www bringperlickhome com 32 PROPER PRODUCT STORAGE The low temperature wine zone will accommodate 42 to 90 bottles of wine dependent on the model The high temperature wine zone will accommodate 48 to 96 bottles of wine dependent on the model Specially designed full extension wine racks allow for proper horizontal storage of the wine The cork remains moist which keeps air from entering the bottle Do not block internal louvers or fan guard openings as this will decrease operating performance CONTROL SETTINGS The cabinet is shipped with the controllers turned ON To turn the refrigeration system OFF or ON press the blue soft button on the front face of the low temperature wine zone controller if the controller is turned off with power applied to the cabinet the LED display will read OFF when tur
80. ront face of the controller if the controller is turned off with power applied to the cabinet the LED display will read OFF when turned on it will read a temperature The controller is located on the top front face of the cabinet above the left door and is equipped with a tinted see through lens which opens by pulling out on the bottom of the lens and rotating upwards Always ensure lens cover is closed before closing door to avoid damage to the controller or lens The wine cooler electronic control comes preset for a product temperature of approximately 55 F with a product temperature adjustability range of 40 F to 70 F To change temperature controller settings see section TEMPERATURE CONTROLLER ADJUSTMENTS on page 42 IMPORTANT NOTE THE LED DISPLAY IS READING ACTUAL AIR TEMPERATURE NOT PRODUCT TEMPERATURE UNDER THESE CONDITIONS A 4 F AIR TEMPERATURE SWING IN THE WINE COOLER COMPARTMENT DOES NOT CHANGE THE ACTUAL PRODUCT TEMPERATURE PRODUCT TEMPERATURE REMAINS AT A VERY STABLE TEMPERATURE LIGHT SWITCH AND BULB Your Two Door All Wine Cooler model has two interior lights that are illuminated when each door is opened The cabinet also comes standard with manual light switches located next to each light for displaying your products through glass door If manual light switch is left on for an extended period of time it may increase the cabinet temperature and in turn product temperature especially in close proximi
81. s standard with manual light switches located next to each light for displaying your products through a glass door If manual light switch is left on for an extended period of time it may increase the cabinet temperature and in turn product temperature especially in close proximity to the light at the top and cause the refrigeration system to run longer e THREE DOOR REFRIGERATOR WINE COOLER WINE COOLER OPERATION The Perlick Three Door Refrigerator Wine Cooler Wine Cooler HSRWW comes equipped with a state of the art refrigeration system The compressor is of a variable speed variety which automatically changes speeds based on system conditions and load The cabinet is equipped with three adjustable digital temperature controllers and LED displays The refrigerator controller can be adjusted through a range of 30 F to 42 F The refrigerator controller has been factory set to modulate from 34 F to 40 F The low temperature wine cooler controller can be adjusted through a range of 45 F to 56 F The low temperature wine cooler zone controller has been factory set to modulate from 54 F to 56 F The high temperature wine cooler controller can be adjusted through a range of 55 F to 68 F The high temperature wine cooler zone controller has been factory set to modulate from 64 F to 66 F To properly determine product temperature see CHECKING PRODUCT TEMPERATURE on page 44 IMPORTANT NOTE ALWAYS ALLOW CABINET TO RUN FOR A
82. see through lens which opens by pulling out on the bottom of the lens and rotating upwards Always ensure lens cover is closed before closing door to avoid damage to the controller or lens The refrigerator control looks and responds identical to the freezer control with the exception that it only controls the cooling system for the refrigerator zone and is located above the center door The freezer electronic control comes preset for a product temperature of approximately O F with a product temperature adjustability range of 5 F to 5 F The refrigerator electronic control comes preset for a product temperature of approximately 38 F with a product temperature adjustability range of 33 F to 42 F To change temperature controller settings see section TEMPERATURE CONTROLLER ADJUSTMENTS on page 42 IMPORTANT NOTE THE LED DISPLAY IS READING ACTUAL AIR TEMPERATURE NOT PRODUCT TEMPERATURE UNDER THESE CONDITIONS AN 8 F AIR TEMPERATURE SWING IN THE FREEZER COMPARTMENT AND A 2 F AIR TEMPERATURE SWING IN THE REFRIGERATOR COMPARTMENT DOES NOT CHANGE THE ACTUAL PRODUCT TEMPERATURE PRODUCT TEMPERATURE REMAINS AT A VERY STABLE TEMPERATURE LIGHT SWITCH AND BULB Your Three Door Freezer Refrigerator Refrigerator has three interior lights that are illuminated when each respective door is opened The cabinet also comes standard with a manual light switches located next to each light for displaying your products through a glass door
83. ser free from dust and dirt will ensure effi cient operation CAUTION Do not bend the fins while brushing the front of the condenser Form No 22259 Rev 1 17 05 www bringperlickhome com 48 Trouble Shooting Direct Draw Dispensers Self Contained Beer Service Problems Cloudy Beer Wild Beer Dispensed beer has either too much foam or is all foam CAUSES W Beer has been dispensed improperly Solution See pouring instructions on page 8 Regulator pressure is set too high Warm keg temperature Solution Keg must be colder than 40 Target temperature is between 36 and 38 W Cabinet door is opened and closed frequently and temperature is warmer than 38 F Solution Adjust temperature to between 36 and 387 W Kinks dents or obstructions in the line Using oddly shaped glasses Frosted waxed or styrofoam containers may cause foaming m Dispenser has been turned off for a long period of time W Faucet is bad dirty or in a worn condition Regulator malfunction Flat Beer Foamy head disappears quickly beer lacks brewery fresh flavor Causes Dirty glassware W CO pressure is too low due to leak or pressure setting CO2is turned off at night Cooler is too cold m leak or defective sticking check valve m Sluggish CO2 regulator CORPORATION Form No 22259 Rev 1 17 05 Beer in glass appears hazy not clear
84. ten coupling Attach faucet handle to the faucet AIR DISTRIBUTOR CO2 TANK 6 FLANGE SLEEVE REGULATOR BEER CONNECTION ALL HOSE CONNECTIONS USE WORM DRIVE HOSE CLAMPS View enlarged for clarity KEG KEG COUPLER DISTRIBUTOR IS ONLY ON MULTIPLE KEG UNITS EACH KEG IS CONNECTED TO A VALVE ON THE AIR DISTRIBUTOR SINGLE KEG IS CONNECTED DIRECTLY TO THE NOTE REGULATOR Image does not accurately reflect positions of the different elements within the unit Positions and hose lengths shown are to clearly illustrate proper connection methods only Perlick is committed to continuous improvement Therefore we reserve the right to change specifications without prior notice Form No 22259 Rev 1 17 05 2 www bringperlickhome com 45 Installation and Tapping Direct Draw Dispensers Self Contained Connecting the Keg Coupler when Supplied by Perlick Place one brown leather washer into black beer line connector hose on hex nut side Screw connector to stainless steel beverage line on faucet standard Tighten with a wrench but do not over tighten Make sure lever handle on the keg coupler is in the UP untapped position Place one brown leather washer into wing nut end of black beer line connector hose and thread onto top of keg coupler Hand tighten m Place clamp on one end of red air line Push end over air valve located inside cabinet Tighten clamp with screwdriver Turn sh
85. the refrigeration system OFF or ON press the blue soft button on the front face of the controller if the controller is turned off with power applied to the cabinet the LED display will read OFF when turned on it will read a temperature The controller is on the top front face of the cabinet above the left door and is equipped with a tinted see through lens which opens by pulling out on the bottom of the lens and rotating upwards Always ensure lens cover is closed before closing door to avoid damage to the controller or lens The refrigerator electronic control comes preset for a product temperature of approximately 38 F with a product temperature adjustability range of 33 F to 45 F To change temperature controller settings see section TEMPERATURE CONTROLLER ADJUSTMENTS on page 42 IMPORTANT NOTE THE LED DISPLAY IS READING ACTUAL AIR TEMPERATURE NOT PRODUCT TEMPERATURE UNDER THESE CONDITIONS A 6 F AIR TEMPERATURE SWING IN THE REFRIGERATOR COMPARTMENT DOES NOT CHANGE THE ACTUAL PRODUCT TEMPERATURE PRODUCT TEMPERATURE REMAINS AT A VERY STABLE TEMPERATURE LIGHT SWITCH AND BULB Your Three Door All Refrigerator has three interior lights that are illuminated when each respective door is opened The cabinet also comes standard with manual light switches located next to each light for displaying your products through a glass door If manual light switch is left on for an extended period of time it may increase the cabin
86. the right to change specifications without prior notice Foams 38 40 42 44 www bringperlickhome com 47 Cleaning the Beer System Direct Draw Dispensers Self Contained The entire beer system to include the faucet flexible beer line and tapping devices must be cleaned at regular intervals We recommend flushing the entire system with fresh water immediately after a keg has been emptied Once each month the system should be cleaned chemically It is recommended that you purchase Perlick s Pump Type Sterilizer as shown below It is equipped with an adapter that attaches directly to the faucet shank in lieu of the faucet It is also available with a slip coupling for those who choose to clean their faucets in place Part Nos Description 887 Gallon sterilizer w faucet coupling 887PSC Gallon sterilizer w slip coupling 330z Liquid alkaline cleaner Cleaning the draft beer system will help to eliminate the buildup of the following materials Bacteria Beer is an excellent food for bacteria none of which is harmful Proper conditions may begin the growth of bacteria in draft beer and on the beer faucet By regular cleaning we prevent this bacterial buildup and maintain the quality of the draft beer Greenish or yellowish colored material on the faucet may indicate bacterial growth Yeast All domestic draft beers contain a small amount of yeast which re
87. ty to the light at the top and cause the refrigeration system to run longer TWO DOOR MULTI ZONE WINE COOLER OPERATION The Perlick Two Door Multi Zone Wine Cooler H2WW comes equipped with a state of the art refrigeration system The compressor is of a variable speed variety which automatically changes speeds based on system conditions and load The cabinet is equipped with two adjustable digital temperature controllers and LED displays The low temperature wine zone controller located above the left door can be adjusted through a range of 40 F to 56 F The low temperature wine zone controller has been factory set to modulate from 53 F to 57 F The high temperature wine zone controller located above the right door can be adjusted through a range of 52 F to 65 F The high temperature wine zone controller has been factory set to modulate from 64 F to 66 F To properly determine product temperature see CHECKING PRODUCT TEMPERATURE on page 44 www bringperlickhome com 25 IMPORTANT NOTE ALWAYS ALLOW CABINET TO RUN FOR A MINIMUM OF 24 HOURS TO ALLOW TEMPERATURE STABILIZATION AFTER START UP BEFORE STORING PERISHABLE ITEMS IMPORTANT NOTE PERLCK S MULTI ZONE UNITS ARE NOT DESIGNED FOR OUTDOOR APPLICATIONS INSTALLING MULTI ZONE UNITS OUTDOORS WILL VOID THE WARRANTY This cabinet is a frost free model meaning the evaporator cooling coil automatically defrosts during off cycles The controller
88. ut off valve to OFF horizontal position Place clamp on the other end of red air line and push over tailpiece on coupler Tighten clamp with screwdriver CAUTION Do not use keg coupler as a handle to lift keg Tapping a Single Valve Keg Sankey W Be sure beer faucet is in closed position m Align keg lugs with lug openings on bottom of coupler m Turn clockwise 1 4 turn Pull handle out and down Keg is now tapped W Open shut off valve on air divider located inside of the cabinet Important Be sure to close this valve when untapping keg Perlick is committed to continuous improvement Therefore we reserve the right to change specifications without prior notice Connecting the Regulator to the CO2 Cylinder m Remove blue plug from regulator fitting Note Do not remove the carbonic washer W Screw regulator onto gas cylinder valve Tighten with wrench until vertically straight Be sure that shut off valve black lever on regulator is in the OFF horizontal position W Place a screw clamp over end of red air line and push onto regulator tailpiece Tighten clamp with a screwdriver REGULATOR FITTING co2 VALVE PRESSURE GAUGE co2 GAS DRUM FITTING FOR REDAIRHOSE REGULATOR ADJUSTING SHUT OFF VALVE SCREW BLACK LEVER IN CLOSED POSITION Adjusting the CO2 Gas Flow Turn regulator adjusting screw counterclockwise until it turns freely
89. y also have other rights which vary from state to state www bringperlickhome com 43 INSTALLATION AND OPERATION INSTRUCTIONS DIRECT DRAW DISPENSER SELF CONTAINED MODELS IMPORTANT INFORMATION Fill out the enclosed warranty card and mail to the Perlick Corporation to register the warranty If the card is not returned the warranty period will begin from the date the equipment is shipped from the factory This manual has been prepared to assist you in the installation of your Direct Draw Dispenser and to acquaint you with its operation and maintenance We dedicate considerable time to ensure that our products provide the highest level of customer satisfaction If service is required your dealer can provide you with a list of qualified service agents For your own protection never return merchandise for credit without our approval We thank you for selecting a Perlick product and assure you of our continuing interest in your satisfaction WARNING When lifting the full weight of the cabinet must be supported Lift from the cabinet base and not from the top Improper lifting can result severe damage to the cabinet 1C CORPORATION MODEL NOS H Series Table of Contents PREPARING THE CABINET FOR USE Installing Faucet and Standard 2 TAPPING Connecting the Keg Coupler 3 TAPPING ANS ooo

H1, H2 and H3 Operation Manual

Contents

Download Pdf Manuals

Related Search

Related Contents