Energy meter demonstration kit based on the STPMC1 and STPMS1
Contents
1. Test points available are GND VCC stepper counter display connector CLK DAT VREG F N The STEVAL IPE011V1 should be plugged into the motherboard using the connector on the edge of the board Voltage inputs are pin F hot wire and N neutral wire Current input load wire should be passed through the current transformer placed on the non component side of the module Jumpers settings The on board jumpers JP1 and JP2 allow the setting of the STPMS1 device according to Table 3 and Table 4 below Table 3 Modes of operation JP1 MSO Description 1 VCC ampl 32 2 NCLK Reserved 3 GND ampl 8 4 CLK Reserved Table 4 Changing of band gap voltage reference JP2 MS1 Description 1 VCC TC 190 ppm C 2 NCLK TC 125 ppm C 3 GND TC 100 ppm C 4 CLK TC 170 ppm C Doc ID 15971 Rev 1 ky UMO746 Getting started 3 Getting started 3 1 Board assembly Assemble the board as illustrated in the figure below Figure 3 STEVAL IPE010V1 assembly ky Doc ID 15971 Rev 1 7 10 Getting started UMO746 3 2 Board connection Plug in the daughterboard as shown in the figure below Figure 4 STEVAL IPE010V1 assembly Use the connectors DAR DAS DAT DAN optional for 4 wire with tamper systems as shown in the figure below Figure 5 STEVAL IPE010V1 assembly WARNIN AAA A ate ot JPA i PR JPA AA A sgi2. wa UMO746 y User manual Energy meter demonstration kit based on the STPMC1 and STPMS1 Introduction The STEVAL IPE010V1 demonstration board is designed to provide the user with a ready to use energy meter application for the STPMC1 device while the STEVAL IPE011V1 is a demonstration board for its companion chip STPMS1 The package contains a STEVAL IPE010V1 motherboard and three STEVAL IPE011V1 daughterboards Additional daughterboards can be ordered if required The demonstration board can be used in two ways m For demonstration purposes by connecting the demonstration platform to an AC power source and setting the parameters through the GUI graphical user interface and the parallel hardware programmer reader m For user application evaluation and development Note The boards do not come programmed or calibrated Figure 1 STEVAL IPE010V1 motherboard Figure 2 STEVAL IPE011V1 daughterboard April 2010 Doc ID 15971 Rev 1 1 10 www st com Contents UMO746 Contents 1 Safety TINS io ica jc in nfm fh Si i Di a 0 pa a iS al 3 1 1 Operating conditions sara ds e a 3 1 2 Features i ee ee ee ee ee eee ee a eee 3 1 3 FIGIGIGNCES score iaa iS bee eeta eae a 4 1 4 Getting technical support ssas ewes be Ge Ne eeee weds bee ees bee ee 4 2 STEVAL IPE010V1 components 00 0c eee eee ee eee 5 2 1 Package CONICS cirios e a e a e de ed 5 22 STEVALIPEOIOV coses ici reporenos
3. RST 3 phase 3 wire RST_ 3 system RST_ tamper 3 phase 3 wire RST_ 2 system R_T_ Aron 2 phase 3 wire _STN 2 system _ST_ America 1 phase 2 wire __ TN 2 system _ST_ tamper 1 phase 2 wire __TN 1 system __T_ e 4LEDs showing Power No load condition Tamper detection Reverse current direction Embedded capacitive power supply Isolation of current channel Doc ID 15971 Rev 1 3 10 Safety rules UMO746 1 3 1 4 4 10 References This document describes how to use and set up a basic test session with a GUI Additional information can be found in the following documents STPMC1 datasheet STPMS1 datasheet STMicroelectronics application notes Schematic diagrams Getting technical support Technical assistance is available without charge to all customers For technical assistance documentation and information on product upgrades and services please refer to your local ST distributor office STmicroelectronics offers its customers a free technical support service with online support at www st com Before contacting us we advise you to confirm that you are using the latest version of the software firmware Upgrades are available without charge at http www st com metering Doc ID 15971 Rev 1 ky UMO746 STEVAL IPE010V1 components 2 STEVAL IPE010V1 components 2 1 Package contents The package contains a 1STEVAL IPE010V1 motherboard b 3STEVAL IPE011V1 daughterboard c 1 parallel progra
4. e ERDEI AER 5 23 STEVAL IPE011V1 sscepeeckad reia as da 6 2 3 1 Jumpers settings ooooooooo eee 6 3 Getting started ic a mrs em ml AAA ne am 7 3 1 Board assembly lt a sine tee ee eee Ke hee RRA ee eS Kee 7 3 2 Board connection ao rr pan dvs dene rede be ie 8 4 Revision history oia ic ao oS a 9 2 10 Doc ID 15971 Rev 1 ky UMO746 Safety rules 1 Safety rules This board can be connected to mains voltage 220 V 110 V In the case of improper use faulty installation or malfunction there is a danger of serious personal injury and damage to property All operations such as transport installation and commissioning as well as maintenance should only be carried out by skilled technical personnel applicable accident prevention rules must be observed Due to the risk of death when using this prototype on mains voltage 220 V 110 V only skilled technical personnel who are familiar with the installation mounting commissioning and operating of power electronic systems and have the relevant qualifications required to perform these functions may use this prototype 1 1 Operating conditions Table 1 Operating conditions Condition Value Unit Vuom 230 VRMS Inom CT Inom 1 Arms Imax CT Imax 30 Arms fLIN 50 60 10 Hz Top 40 85 eC 1 2 Features e Modularity Programmability e Supports 3 phase 4 wire RSTN 4 system RSTN tamper extra module is needed 3 phase 4 wire RSTN 3 system
5. other names are the property of their respective owners O 2010 STMicroelectronics All rights reserved STMicroelectronics group of companies Australia Belgium Brazil Canada China Czech Republic Finland France Germany Hong Kong India Israel Italy Japan Malaysia Malta Morocco Philippines Singapore Spain Sweden Switzerland United Kingdom United States of America www st com 10 10 Doc ID 15971 Rev 1 ki
6. ES a ae ee ee me MA de i lt alk ot oll ot ll at ok a Te i w amp dada 8 10 Doc ID 15971 Rev 1 UMO746 Revision history 4 Revision history Table 5 Document revision history Date Revision 06 Mar 2010 1 Initial release Changes Doc ID 15971 Rev 1 9 10 UMO746 Please Read Carefully Information in this document is provided solely in connection with ST products STMicroelectronics NV and its subsidiaries ST reserve the right to make changes corrections modifications or improvements to this document and the products and services described herein at any time without notice All ST products are sold pursuant to ST s terms and conditions of sale Purchasers are solely responsible for the choice selection and use of the ST products and services described herein and ST assumes no liability whatsoever relating to the choice selection or use of the ST products and services described herein No license express or implied by estoppel or otherwise to any intellectual property rights is granted under this document If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party product
7. mmer reader d Promotional CD 2 2 STEVAL IPE010V1 This is the motherboard which can accept up to 5 daughterboards An STPMC1 is mounted on the module and 4 LEDs indicate the status of the system The motherboard can be connected to a PC using the parallel programmer reader through the P1 connector The board can be supplied from an external DC source 3 3 to 5 V through the W34 connector Test points available are LED MOP MON stepper counter display connector GND CLK DAR DAS DAT DAN DAH For 3 phase 4 wire 3 wire systems only three daughterboards are needed for a complete measurement system Table 2 P1 connector pin description Pin Pin name Functional description 1 VOTP Power supply input of 15 0 V during permanent write to OTP cells 2 Not connected 3 GND Signal reference level O V and power supply return 4 SDA TD SPI interface data 5 SCS SPI interface enable 6 SCL NLC SPI interface clock 7 Not connected 8 SYN NP SPI interface signal 9 Not connected 10 VCC Power out of 3 3 or 5 V Doc ID 15971 Rev 1 5 10 STEVAL IPE010V1 components UMO746 2 3 2 3 1 6 10 STEVAL IPE011V1 This is the daughterboard Each module serves one single phase converting the voltage and current information multiplexing them and sending the stream to the STPMC1 Each of the boards must be connected to the voltage source of the relative phase and to the load
8. s or services or any intellectual property contained therein UNLESS OTHERWISE SET FORTH IN ST S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION OR INFRINGEMENT OF ANY PATENT COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE ST PRODUCTS ARE NOT RECOMMENDED AUTHORIZED OR WARRANTED FOR USE IN MILITARY AIR CRAFT SPACE LIFE SAVING OR LIFE SUSTAINING APPLICATIONS NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY DEATH OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ST PRODUCTS WHICH ARE NOT SPECIFIED AS AUTOMOTIVE GRADE MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER S OWN RISK Resale of ST products with provisions different from the statements and or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever any liability of ST ST and the ST logo are trademarks or registered trademarks of ST in various countries Information in this document supersedes and replaces all information previously supplied The ST logo is a registered trademark of STMicroelectronics All
Download Pdf Manuals
Related Search