PRD Periodic Examination Guide Version
Contents
1. 0444404 I SAN III 77 777277 7777 AUT TI TTT 777 77272777 AUT TI II 7772 7 7 777 AUT 179 SSA 11117770 SY UVA AUN 111111 11111422 CTT 7777797 Soul QULLULUL TT DESCENT DEVICE PRD D ring Inspect the D ring connector for signs of damage excessive wear distortion corrosion or cracking Ensure that the descent line is not paid out of the device this would indicate that a descent has occurred Open backpack Open the backpack containing the descent device Inspect the general condition of the descent device for signs of damage or corrosion Ensure that the drum label is present and legible O Rope slack Inspect descent line for any slack between the drum and rack If line shows any sign of slack remove the PRD from service and refer to Latchways or authorised agent Release pin Inspect the release pin for signs of damage distortion corrosion or cracking Ensure that it has not been disengaged Ensure that the red release cord is positioned under the release pin and that the load line webbing is looped around the release pin Ensure that the green release pin clip is present and undamaged check for signs of damage distortion or cracking If damage is apparent remove the gt PRD from service and refer to Latchways or authorised agent Release cord Ensure that the release cord guide is undamaged Inspect the descent line load line and release cord for signs of2. 0 9 m 0 c 9 Fer G E G x LU Latchways Personal Rescue Device Periodic Examination Instructions Guide roo ar CHWAY S 62801 97UK_Issue 1000 FALL PROTECTION Guidance notes in the use of this periodic examination instructions manual Periodic examination instructions These are the detailed descent device and harness checks that should be carried out by a competent person at least once every twelve months however local state governmental and jurisdictional agencies may require more frequent or mandatory periodic examinations of which the user is required to comply Additionally environmental conditions may be such that more frequent periodic examinations may also be necessary The periodic examination should be recorded in the periodic examination log WARNING No repairs modifications or alterations are to be carried out on the Latchways Personal Rescue Device PRD Competency The PRD has been specifically designed as a user friendly device incorporating a range of features to aid pre use checks and on site periodic examination Therefore no disassembly or servicing is required However if during the examination defects or concerns are found the unit shall be removed from service and returned to Latchways or authorised agent Examination procedure X WARNIN Periodic examination should be carried out by an authorised Latchways technician only An authorised Latchways technician me
3. webbing through the hands whilst twisting lightly to check for surface defects or changes in the flexibility of the material Localised hardening of the webbing may indicate damage or excessive wear Rough areas present on the surface of the webbing may indicate abrasion of the webbing If any sections of webbing show damage remove the PRD from service and refer to Latchways or authorised agent x If the harness has been subjected to paint overspray it must not be P used and should be referred to Latchways or authorised agent Stitching inspection Check all stitching for signs of loosening pulling or cut thread There must be no evidence of damaged stitching on either side of the stitch pattern If any sections of stitching show damage x remove the PRD from service and refer to Latchways or authorised agent x bonos A 18 Metalwork inspection Check metal fittings for damage corrosion deformation or cracking Check edges of buckles and D rings for burring or sharp edges If any coatings on metallic components have worn ensure that the underlying metal surface does not show any corrosion If there are any signs of corrosion x remove the PRD from service and refer to Latchways or authorised agent Replace examination label C 0194 Remove examination date label from device atat sE mlalm lslalsiolnio drum as shown 1213 14 15 1617 18 19 20 Mark the new examinati
4. ans a person who is trained and approved by Latchways in identifying hazards or dangerous conditions of the PRD This manual is intended to serve as a reminder of the processes required for a full examination and not a comprehensive set of instructions Periodic examination log Dates and Details of examinations must be recorded in the Periodic Examination Log and the label located on the device drum Examination Date label Latchways part number 68200 42 must be updated accordingly Safety equipment Ensure that you carry out any service procedures in conjunction with local safety rules In addition ensure that you are wearing gloves Note This service guide must be reproduced or printed in colour to ensure correct guidance is followed Tools needed To carry out this periodic examination of the PRD you will require the following basic tool set Safety Gloves 1 x 3 mm Hexagonal Bit 1 x Torque Wrench capable of 1 3 Nm Loctite 2701 Thread Locker 1 x Hole Punch Never attempt to modify or disassemble any components within the PRD other than those stated in this guide WAR N l N Never attempt to modify or disassemble any components within the PRD other than those stated in this guide Part names and terminology 01 D Ring connector 02 Buckle 03 Backpack 04 Red Release Cord 05 Secondary Activation Point 06 Toolbag Attachment Point 07 Harness 10 08 Strap Sliders 09 Re
5. cuts abrasion fraying tears mould discolouration chemical attack or excessive build up of dirt Check the stitching for signs of loosening pulling or cut thread Excessive build up of dirt may prevent the descent line from pulling through the device If damage is apparent remove the PRD from service and refer to Latchways or authorised agent Open backpack and remove descent device Remove descent device from backpack Undo the seven M4 x 12 socket caphead bolts using a 3 mm hexagonal bit Carefully remove the back cover retaining the silicon gasket in the cavity Remove back case Once the back cover is removed inspect the general conditions for signs of water ingress corrosion contamination or damage If any damage is found remove x the PRD from service and refer to Latchways or authorised agent Check main gear and ratchet Rotate the ratchet clockwise Turn the main gear by hand in both directions to ensure that it is still free to rotate If the gear is not free to rotate remove the PRD from service and refer to Latchways or authorised agent UN Replace ratchet and main gear Ensuring no slack line on the drum rotate the gear clockwise as far as it will go Whilst holding the gear rotate the ratchet anti clockwise back into place then release the main gear The gear may rotate anti clockwise for one or two clicks this is acceptable Check that the ra
6. lease Pin 10 Load line Webbing 11 Descent Device 12 PRD Label 13 Green Release Pin Clip 14 Rack 15 Examination Label 16 Drum 17 Descent Line A TIT Replacement kits W Examination Date labels Back cover gasket Latchways part number 68200 42 68200 22 OOO E General inspection Inspect the general condition of the PRD harness and backpack for signs of damage contamination abrasion fraying tears burns mould discolouration or chemical attack If excessive signs of the above x are found remove the PRD from service and refer to Latchways or authorised agent LAMA AMADA UU AMIA AA IA Guvwanens ALFT FETT NOT TTT III ID NASE UELRERREDRBDDDD wer We AU DURE SS A LS Tuna 77177 ULA 777 7 7 8 y eS 1i 2727 SN Pee ey A r7 7277 QGGERERBREBBe eee 173 yee kas Wo a Ot a AE E CE OA i SSG EERE ERE eae ye UTE NAA lla ay u 17 Tr 7777777 ACTO TUTTI TIT TT TT SIS A TITTI T MA Pi iit ft AD SST UL 1222222 SECTII SOU ere Olla Sap OPW AEETI TI ARCU EU U U W A A 1177722 SOMA Re UU III A IT 11777777777 ECT III ONU AMAN PPP PP RER 88 OCCU IT O 979 WOU WOU AU AA s 000099 WAG GG PRP AUT PY SETE Ta OEOD AA itii TIEFER piriti SELI SSP eer fs SA sa MTE TELER OOIT ETETETT TU t i PERES SAA A 110111112222 ELSA AA 779999 SSA 1170000 SAID SSOSQQUHREEEEE Rea ee Pr AU IIA SSA II 11472 SOU AAA
7. ng inspection part 1 Check the legibility of the product markings on the harness Check all webbing for signs of cuts abrasion fraying tears burns mould discolouration or chemical attack If any sections of webbing show damage remove the PRD from service and refer to Latchways or authorised agent POLYESTER WEBBING SANGLE EN POLYESTER MATERIALE IN POLIESTERE POLY BE SAT CHWAYS A KG 130 LBS FALL PROTECTION As KG 310 LBS CINCHA DE POLI STER POLYESTER WEB WARNING READ INSTRUCTIONS BEFORE USE INSPECT BEFORE EACH USE AVERTISSEMENT LIRE LES CONSIGNES AVANT UTILISATION ET INSPECTER AVANT CHAQUE UTILISATION A ATTENZIONE LEGGERE LE ISTRUZIONI PRIMA DELL USO E CONTROLLARE PRIMA DI OGNI UTILIZZO WARNUNG ANWEISUNGEN VOR ae ANTES DET Us UND VOR JEDER NUTZUNG MEIER ADVERTENCIA LEA LAS INSTRUCCIO USO E INSPECCIONE ANTES DE CADA USO WAARSCHUWING LEES DE TANWUZNGEN VOO VOOR GEBAUK EN INSPECTEER ELKE KEER VOOR GERUK SS 1777000 Sy D ueanans ame IPPFFFeM OCCU 11111777777 wur WP anno MD j 1 777 a ADDI ES SS 1707 AAA SN 2277 UT TTTTUUT ALLEL 7 77 AUU IT 777 77777 N NN N H 0A 1 77 777 eer ON SUL 67117777 ya eee CN a oy un 2777 A D Reece 111117 777777997 OCCU OA SL aa ALD ye SOS SSA 1111177770 OCU ACUM es 10 Webbing inspection part 2 O Run
8. on date label with the date of the next due certification with the aid of ee a hole punch and place into the window in the SHOULD B main label as shown 12 Y Complete periodic examination log Complete the periodic examination log found in the user manual of the PRD including the date of inspection and date of next examination If the periodic examination log is missing or illegible contact Latchways for a replacement Providing every section of this service guide has been completed the PRD is now fully examined and can be returned to service Notes Latchways Personal Rescue Device is a registered trademark of Latchways plc are IHVVAYS Latchways plc Hopton Park Devizes Wiltshire SN10 2JP England Tel 44 0 1380 732700 Fax 44 0 1380 732701 Email info latchways com Website www latchways com 62801 9 7UK_Issue 1
9. tchet tip is fully engaged with the teeth in the main gear Inspect the back cover gasket checking for damage contamination degradation and ensure that it is fully seated and not twisted in the back cover cavity If damage is apparent to the gasket it must be replaced Latchways x part number 68200 22 or the PRD removed from service and referred to Latchways or authorised agent O y Replace back cover Apply Loctite 2701 threadlocker to the seven M4 x 12 socket caphead bolts Replace the back cover onto the unit and secure using the bolts torqueing to 1 5 Nm each It is good practice to tighten 2 bolts at opposite ends of the back cover T N o THREAD LOCKER Replace descent device into backpack Replace descent device into backpack After inspection close the zip on the backpack fully Open back side of backpack Unzip the back panel of the backpack and inspect the harness connector for signs of damage distortion corrosion or cracking Ensure that the fastening bolt is secure If damage is apparent remove the x PRD from service and refer to Latchways or authorised agent HARNESS NOTE If PRD is used with a harness not supplied by Latchways inspect the harness in accordance with the instructions provided with the harness in addition to the following instructions Note that in such cases labels and or metalwork may be in different locations to those pictured Webbi
Download Pdf Manuals
Related Search