BTX-700SW preliminary manual
Contents
1. 0 127 Index Ch17 255 Rotation Fast 194 Rotation Slow 190 193 Stop 189 Rotation Slow O 128 Rotation Fast 0 127 Index R Prism 8 255 0 7 Ch18 Frost Normal BRITEQ 27 BTX 700SW 29Channels Mode 3 Ch24 Ch25 Ch26 Ch27 Ch28 Ch29 255 0 248 255 Open 255 24027 Random 204 239 Siow close 132 167 Slow Gen 37 S s Open Blackout 0 Download update file if available from www briteq lighting com follow the user manual of our firmware updater not included order code 4319 to update the fixture 8 Update Software 9 Troubleshooting Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting The unit does not work no light and the fan does not work Check the connect power and main fuse Measure the mains voltage on the main connector Check the power on LED to see if it can be light up or not Not responding to DMX controller 1 DMXLED should be on If not check DMX connectors cables to see if they are linked properly 2 If the DMX LED is on and no response to the channel check the address settings and DMX polarity If you have intermittent DMX signal problems check the pins on connectors PCB of the unit or the previous one 4 Try to use another DMX controller 5 Check to see if the DMX cables run near or run alongside high voltage cables that may cause2. 021 026 016 020 011 015 006 010 000 005 06606000090 255 Rotation Fast 194 Rotation Slow 190 193 Stop 189 Rotation Slow 128 Rotation Fast 064 127 Color Mix 056 063 Blue 048 055 Green 040 047 Pink 032 039 5600K 024 031 3200K 016 023 Orange 008 015 Red 001 007 White 128 255 28 Prism Rotation Effects 8 127 Prism Effect 0 7 No Function BRITEQ 23 BTX 700SW BRITEQ 24 BTX 700SW Chi2 255 Rotation Fast Si 194 Rotation Slow 190 193 Stop 189 Rotation Slow 2 128 Rotation Fast 0 127 Index 17 2 0 22Channels Mode 2 Ch13 Ch14 Ch15 Ch18 255 0 0 0 Ch19 Ch20 Pan Tilt Speed 0 Slow Fast Ch21 8 255 Frost 0 7 Normal Ch16 Pan Ch22 250 255 Disable Flatb 240 249 Enable Flatb 230 239 Lamp Off 210 229 No Function 200 209 Reset 190 199 Iris Flatb Reset 180 189 Focus Zoom Prism Frost Reset 170 179 Shutter reset 160 169 Gobo1 Gobo2 Reset 150 159 Color CMY Reset 140 149 Pan Tilt reset 130 139 Lamp On 120 129 Disable Blackout while gobo change 110 119 Enable Blackout while gobo change 100 109 Disable Blackout while color change 090 099 Enable Blackout while color change 080 089 Disable Blackout while Pan Tilt Move 070 079 Enable Blackout while Pan Tilt Move 000 069 No Function 29 Channels mode Pan Tilt Macro 248 255Macro31 240 247Macro30 232 239Macro29 224 231Macro28 216 2
3. BTX 700SW Active Select Active press ENTER button to confirm use UP and DOWN button to select Yes wireless control available or No wireless control unavailable press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode Set wireless control to be available the power indicate LED will strobe Retransmit Select Retransmit press ENTER button to confirm use UP and DOWN button to select Yes or No press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode Reset Memory Select Reset Memory press ENTER button to confirm use UP and DOWN button to select Yes refuse wireless signal or No press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode Fixture Setting Enter menu mode select Fixture Setting press ENTER button to confirm use UP and DOWN button to select Pan Inverse Tile Inverse BL O P T Moving BL O Color Change or BL O Gobo Change Pan Inverse Select Pan Inverse press ENTER button to confirm present mode will blink on the display use UP and DOWN button to select No normal or Yes pan inverse press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode Tilt Inverse Select Tilt Inverse press ENTER button to confirm present mode will blink on the display use UP a
4. 700SW Easy calibration and maintenance by magnetic home positioning Module design for easy assembly and service Prism 3 facets prism with rotating effect Frost Variable separate effect Focus Focus effect Iris Motorized stepless Zoom Motorized linear zoom for smooth adjustment of beam size and beam sharpness Cool Fan cooled Protocols DMX 512 Date input output 3 5 Pin XLR socket Weight 23 2kgs Dimension 447x 369 597 mm Photometric diagram lux 35 6500 1600 700 440 lux 15 26800 6700 3000 1770 Distance m 5 10 15 20 Spot dia m 15 1 2 2 6 3 8 9 2 Spot dia m 35 3 0 6 0 9 0 12 BRITEQ 4 BTX 700SW DM Mode 1 Mode 2 Mode 3 Tilt Cyan Tilt Tilt Fine Magenta Tilt Fine Pan Tilt Speed Pan Tilt Speed Shutter Color Function Dimmer Gobo 1 Pan Tilt Macro X Channels 3 A 6 r E E 10 11 13 14 15 17 21 R Gobo 1 CMY Speed aX O Focus Frost R Prism 22 ig 11 Iris pom Focus J ES ELE Ee 4s Shutter Dimmer Fine N 4 2 01 AI O 1 Arm 2 Front panel 3 head 4 Tilt lock button Black 5 Tilt unlock button Gray 6 Pan lock 7 Handle 8 Base 9 Antenna optional The head be locked for transportation protection the tilt lock button 4 is pressed and BRITEQ 5 BTX 700SW the pan lock unlock lever 6 is in lock po
5. BTX 700SW BRITEQ 26 BTX 700SW Ch13 Ch14 234 255 Color11 13 233 Color10 192 212 Color9 171 191 Color8 149 170 Color7 128 148 Color6 107 127 Color5 086 106 Color4 064 085 Color3 043 063 Color2 022 042 Color1 000 021 White Ch19 Ch20 Ch21 Ch22 Ch23 255 Rotation Fast 194 Rotation Slow 190 193 Stop 189 Rotation Slow 128 Rotation Fast 118 127 Gobo2 8 Shaking 108 117 Gobo2 7 Shaking 098 107 Gobo2 6 Shaking 088 097 Gobo2 5 Shaking 078 087 Gobo2 4 Shaking 068 077 Gobo2 3 Shaking 058 067 Gobo2 2 Shaking 048 057 Gobo2 1 Shaking 042 047 037 041 032 036 027 031 021 026 016 020 011 015 006 010 000 005 066006090 128 255 29Channels Mode 3 Ch15 235 255Macro12 214 234Macro11 194 213Macro10 173 193 Macro9 153 172 Macro8 132 152 Macro 111 131 Macro6 091 110 Macro 5 070 090 Macro4 050 069 Macro3 029 049 Macro2 008 028 Macro 1 000 007 Open 28 Prism Rotation Effects Ch16 255 Rotation Fast 2 194 Rotation Slow 190 193 Stop 189 Rotation Slow 128 Rotation Fast 118 127 Gobo1 7 Shaking 108 117 Gobo1 6 Shaking 098 107 Gobo1 5 Shaking 088 097 Gobo1 4 Shaking 078 087 Gobo1 3 Shaking 068 077 Gobo1 2 Shaking 058 067 Gobo1 1 Shaking 050 057 043 049 036 042 029 035 022 028 015 021 008 014 000 007 255 Rotation Fast Ki 194 Rotation Slow 190 193 Stop 8 127 Prism Effect 0 7 No Function 189 Rotation Slow 128 Rotation Fast
6. Reset 140 149 Pan Tilt reset 130 139 Lamp On 120 129 Disable Blackout while gobo change 110 119 Enable Blackout while gobo change 100 109 Disable Blackout while color change 090 099 Enable Blackout while color change 080 089 Disable Blackout while Pan Tilt Move 070 079 Enable Blackout while Pan Tilt Move 000 069 No Function 22 Channels mode 2 22Channels Mode 2 h4 248 255 Open Random 240 247 Random Slow Open 204 239 Slow Gen Slow Close 168 203 Fast Open Slow en 132 167 Fast Close 223 16 131 lt lt 5 8 15 Open 0 7 Blackout 255 Rotation Fast 194 Rotation Slow 190 193 Stop 189 Rotation Slow 128 Rotation Fast 118 127 Gobo1 7 Shaking 108 117 Gobo1 6 Shaking 098 107 Gobo1 5 Shaking 088 097 Gobo1 4 Shaking 078 087 Gobo1 3 Shaking 068 077 Gobo1 2 Shaking 058 067 Gobo1 1 Shaking 050 057 043 049 036 042 029 035 022 028 015 021 008 014 000 007 0 90000 25577 100 0 0 0 0 255 Rotation Fast 2 194 Rotation Slow 190 193 Stop 189 Rotation Slow 5 128 Rotation Fast 0 127 Index 255 100 255 100 0 255 Rotation Fast 2 194 Rotation Slow 190 193 Stop 189 Rotation Slow 128 Rotation Fast 118 127 Gobo2 8 Shaking 108 117 Gobo2 7 Shaking 098 107 Gobo2 6 Shaking 088 097 Gobo2 5 Shaking 078 087 Gobo2 4 Shaking 068 077 Gobo2 3 Shaking 058 067 Gobo2 2 Shaking 048 057 Gobo2 1 Shaking 042 047 037 041 032 036 027 031
7. glass gobo 4 Remove the original gobo and inset a new one glazy side towards the lamp Insert the ring to secure it in the gobo holder 5 Install the gobo plate back into the gobo wheel Make sure the gobo plate is installed under the pressure plate Pressure plate A Ger Se 2 BRITEQ 7 BTX 700SW MSR MSD Gold 700 2 miniFastFit e Because of its high internal pressure there might be a risk that the Discharge lamp would explode during operation The lamp emits intense UV radiation which is harmful to the eyes and skin The high luminance of the arc can cause severe damage to the retina if you take a close look at the lamp e To protect the lamp always turn off the lamp first via control panel or DMX controller and let the unit run at least five minutes to cool down before switching off the mains supply Never handle the lamp or luminaries when it is hot e Do not touch the bulb with bare hands If this happens clean the lamp with denatured alcohol and wipe it with a lint free cloth before installation e The lamp generates UV radiation Never operate the lamp without appropriate shielding e When lighting up the lamp operates at high pressure and there is a slight risk of arc tube rupture The risk increases with age temperature and improper handling of the lamp Do not use the lamp longer than its lifespan e Make sure the lamp is located in the center of the reflector for the best projection Ch
8. 00V 240V 50 60 2 Power Consumption 881W 230V 919W 120V Fuse T15A Lamp Philips MSR Gold 700 2 mini FastFit Battery backup display Setting DMX address or other functions without connecting to mains power Battery for LCD display charges automatically when the fixtures connects to the mains power No need to change battery Wireless control for the unit with wireless receiver built in only Wirelessly controlled by W DMX option Each W DMX is sending out 512 channels of DMX License free band of 2 45 GHz Optical system High efficiency optical system delivering extremely powerful output High quality diachronic lenses Beam angle 15 35 Movement Pan 540 Tilt 270 Pan Tilt moving speed adjustable Automatic Pan Tilt correction Easy calibration and maintenance by magnetic home positioning Pan Tilt position lock for transporting protection Shutter Dimmer Blackout 0 100 smooth dimming independent shutter and various strobe effect Color wheel Color wheel 7 diachronic colors open Rainbow effect in both directions Easy calibration and maintenance by magnetic home positioning CMY CMY speed adjustable Optional multiple preset colors and macros available Gobo wheel Gobo size 026 8mm 24mm for image Gobo Wheel 1 7 rotating index able easily replaceable gobos open Gobo Wheel 2 8 metallic gobos open BRITEQ 3 BTX
9. 22 042 Color1 000 021 White Ch17 R Prism 255 Rotation Fast 194 Rotation Slow 190 193 Stop 189 Rotation Slow 128 Rotation Fast 0 127 Index 255 Rotation Fast 2 194 Rotation Slow 190 193 Stop 189 Rotation Slow 128 Rotation Fast 118 127 Gobo1 7 Shaking 108 117 Gobo1 6 Shaking 098 107 Gobo1 5 Shaking 088 097 Gobo1 4 Shaking 078 087 Gobo1 3 Shaking 068 077 Gobo1 2 Shaking 058 067 Gobo1 1 Shaking 050 057 043 049 036 042 029 035 022 028 015 021 008 014 000 007 Ch18 Ch19 Ch20 Ch21 255 Rotation Fast Pp 194 Rotation Slow 190 193 Stop 189 Rotation Slow E 128 Rotation Fast 0 127 Index 255 Rotation Fast 194 Rotation Slow 190 193 Stop 189 Rotation Slow 128 Rotation Fast 118 127 Gobo2 8 Shaking 108 117 Gobo2 7 Shaking 098 107 Gobo2 6 Shaking 088 097 Gobo2 5 Shaking 078 087 Gobo2 4 Shaking 068 077 Gobo2 3 Shaking 058 067 Gobo2 2 Shaking 048 057 Gobo2 1 Shaking 042 047 037 041 032 036 027 031 021 026 016 020 011 015 006 010 000 005 O6060000 128 255 28 Prism Rotation Effects 8 127 Prism Effect 0 7 No Function Ch22 0 255 255p 0 0 255r 8 2554 Frost 0 7 0 10 10096 0 2 0 250 255 Disable Flatb 240 249 Enable Flatb 230 239 Lamp Off 210 229 No Function 200 209 Reset All 190 199 Iris Flatb Reset 180 189 Focus Zoom Prism Frost Reset 170 179 Shutter reset 160 169 Gobo1 Gobo2 Reset 150 159 Color CMY
10. 23Macro27 208 215Macro26 200 207Macro25 192 199Macro24 184 191Macro23 176 183Macro22 168 175Macro21 160 167Macro20 152 159 19 144 151 18 136 143Macro17 128 135Macro16 120 127Macro15 112 119Macro14 104 111 13 096 103 12 088 095 11 080 08 7 10 072 079 9 064 07 1 8 056 063 7 048 055Macro6 040 047Macro 5 032 039Macro4 024 031Macro3 016 023Macro2 008 015 Macro1 000 007 Stop Pan Fine 29Channels Mode 3 255 Rotation Fast 194 Rotation Slow 190 193 Stop 189 Rotation Slow e 128 Rotation Fast 064 127 Color Mix 056 063 Blue 048 055 Green 040 047 Pink 032 039 5600K 024 031 3200K 016 023 Orange 008 015 Red 001 007 White 255 0 25 Pan Tilt Speed 5 255 0 Function 250 255 Disable Flatb 240 249 Enable Flatb 230 239 Lamp Off 210 229 No Function 200 209 Reset All 190 199 1 15 Reset 180 189 Focus Zoom Prism Frost Reset 170 179 Shutter reset 160 169 Gobo1 Gobo2 Reset 150 159 Color CMY Reset 140 149 Pan Tilt reset 130 139 Lamp On 120 129 Disable Blackout while gobo change 110 119 Enable Blackout while gobo change 100 109 Disable Blackout while color change 090 099 Enable Blackout while color change 080 089 Disable Blackout while Pan Tilt Move 070 079 Enable Blackout while Pan Tilt Move 000 069 No Function chit 2 100 25577 100 BRITEQ 25
11. ASSER L APPAREIL D barrassez vous de l appareil et des piles usag es de mani re cologique conform ment aux dispositions l gales de votre pays NL VERWIJDEREN VAN HET APPARAAT Verwijder het toestel en de gebruikte batterijen op een milieuvriendelijke manier conform de in uw land geldende voorschriften RECYCLE DU ENTSORGUNG DES GER TS Entsorgen Sie das Ger t und die Batterien auf umweltfreundliche Art und Weise gem den Vorschriften Ihres Landes ES DESHACERSE DEL APARATO Reciclar el aparato y pilas usadas de forma ecologica conforme a las disposiciones legales de su pais PT COMO DESFAZER SE DA UNIDADE Tente reciclar a unidade e as pilhas usadas respeitando o ambiente e em conformidade com as normas vigentes no seu pais 1 Safety Instruction A N Please read carefully the instruction manual which includes WARNING important information about the installation usage and maintenance Please keep this User Guide for future consultation If you sell the unit to another user be sure that they also receive this instruction manual Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems e Unpack and check carefully that there is no transportation damage before using the unit The unit is for indoor use only Use only in a dry location Do install and operate by qualified operator Do not allow childr
12. BIAS 200 Operation Manual WWW BRITEQ LIGHTING COM C cnyight 202 by BELEC WV Brile d n ot Bijga ium d Reproduction or publication of the content in any manner ere eres a of the publisher is prohibited Version 1 0 A O NT GYOT RESEARCH DANGER GEVAAR GEFAHR PELIGRO PERIGO WARNING DANGER never expose the lens to direct sunlight even for a short period This may damage the light effect or even cause fire ATTENTION DANGER n exposez jamais la lentille directement aux rayons de soleil m me pendant un bref instant Ceci peut endommager l int rieur de l appareil ou m me causer un incendie OPGELET GEVAAR stel de lens nooit bloot aan direct zonlicht zelfs gedurende een korte periode Dit kan het toestel beschadigen en zelfs brand veroorzaken WARNUNG GEFAHR Setzen sie die Linse niemals direkter Sonneneinstrahlung aus auch nicht f r eine kurze Zeit Die direkte Sonneneinstrahlung kann das Ger t zerst ren oder zum brennen bringen ADVERTENCIA jPELIGRO jnunca exponga la lente a la luz solar directa a n durante un per odo corto jEsto puede danar el efecto de luz o incluso causar el fuego AVISO PERIGO Nunca exponha as lentes directamente luz solar mesmo que por pouco tempo Isto pode danificar o efeito luminoso ou mesmo provocar um inc ndio EN DISPOSAL OF THE DEVICE Dispose of the unit and used batteries in an environment friendly manner according to your country FR D CL
13. Fail Dimmer Reset Fail Color Reset Fail Cyan Reset Fail Magenta Reset Fail Yellow Reset Fail Gobo1 Reset Fail R Gobo1 Reset Fail Gobo2 Reset Fail Iris Reset Fail Effect Reset Fail R Effect Reset Fail Frost Reset Fail Flatb Reset Fail Focus Reset Fail Zoom Reset Fail They may appear when turn on or reset the unit for some parts such as board P C are damaged Please contact the qualified maintenance BRITEQ 19 BTX 700SW 7 Control By Universal DMX Controller 7 1 Connection Unit 4 DMX controller Power Power Power Power COMMON DMX JN DMX INPUT DMX OUTPUT e DMX COMMON DMX 53 DMX 52 Not Used ATTENTION Termination reduces signal errors and to avoid signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 ohm 1 4W between pin2 DMX and pin3 DMX of the last 1 At last unit the DMX cable has to be terminated with a terminator Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last unit 2 Connect the unit together in a daisy chain by XLR plug cable from the output of the unit to the input of the next unit The cable cannot be branched or split to a Y cable DMX 512 is a very high speed signal Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 3 The DMX output and in
14. OWN button to offset the value from 128 to 127 press ENTER button to store Press MENU button to exit 1115 1115 home position adjust Enter offset mode Select Iris press ENTER button to confirm the present position will blink on the display use UP and DOWN button to offset the value from O to 255 press ENTER button to store Press MENU button to exit Prism Prism home position adjust Enter offset mode Select Prism press ENTER button to confirm the present position will blink on the display use UP and DOWN button to offset the value from O to 255 press ENTER button to store Press MENU button to exit BRITEQ 18 BTX 700SW R Prism Prism rotation home position adjust Enter offset mode Select R Prism press ENTER button to confirm the present position will blink on the display use UP and DOWN button to offset the value from 128 to 127 press ENTER button to store Press MENU button to exit Frost Frost home position adjust Enter offset mode Select Frost press ENTER button to confirm the present position will blink on the display use UP and DOWN button to offset the value from 0 to 255 press ENTER button to store Press MENU button to exit Flatb Flatb home position adjust Enter offset mode Select Flatb press ENTER button to confirm the present position will blink on the display use UP and DOWN button to offset the value from 0 to 255 press ENTER button to store Press MENU button to exit Focus F
15. P and DOWN button to select No normal while changing gobo or Yes blackout while changing gobo press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode Lamp Setting Attention The lamp will not be on unit detected temperature is lower than 45 C Enter menu mode select Fixture Setting press ENTER button to confirm use UP and DOWN button to select On Off State Power on Off Via DMX On if DMX on Off if DMX off Cooling Mode Ignition Delay or Low Power Delay On Off Turn on off the lamp Select On Off press ENTER button to confirm present mode will blink on the display use UP and DOWN button to select On lamp on or Off lamp off press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode State Power On Lamp state while power on Select State Power On press ENTER button to confirm present mode will blink on the display use UP and DOWN button to select On Lamp on while power on or Off Lamp off while power on press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode Off Via DMX Turn off the unit via DMX controller Select Off Via DMX press ENTER button to confirm present mode will blink on the display use UP and DOWN button to select Yes turn off the unit via DMX controller available or No turn off the unit via DMX controller
16. ange Lamp In case of replacement of the lamp or maintenance do not open the fixture within 15 minutes until the unit cools down after switching off WARNING 1 Turn off the power 2 Unscrew the two screws A open the lamp cover turn it to the position as the sketch shown below 3 Hold the base of the lamp anticlockwise turn until it is parallel to the groove 4 Inset a new lamp follow the groove turn it clockwise to fix the lamp 5 Tighten the screws A to fix the lamp cover 6 Turn the screws B to adjust the lamp position be sure it is located in the center of the reflector for the best projection Lamp cover Lamp base BRITEQ 8 BTX 700SW 6 How To Set The Unit 6 1 Power On Display Bl o Color Change o Lamp 30 C Present temperature of lamp is 30 Every time you turn on the unit it will run built in program to reset all motors to their home position the display will show as fig 4 you may hear some noises for about 20 seconds It will show warning sign if it goes wrong during resetting and you can press the MENU button to view the error information After that the unit will be ready to receive DMX signal and the display will show as fig 5 es DMXAddress Base 40 C Brile 001 A ELGE T RESEARCH Yes Ver x xx Md 1 22Ch Lamp 30 C Fig 4 Fig Explanation of fig 5 Lamp 40 C Present temperature of base CPU
17. built in program to reset iris and flatb to their home positions or No press ENTER button to store Press MENU button to exit All Reset All Select All press ENTER button to confirm use UP and DOWN button to select Yes the unit will run built in program to reset all motors to their home positions or No press ENTER button to store Press MENU button to exit Special Functions Enter menu mode select Special Functions press ENTER button to confirm use UP and DOWN button to select Fixture Maintenance or Factory Setting Fixture Maintenance Select Fixture Maintenance press ENTER button to confirm use UP and DOWN button to select Interval or Remain Time Interval Select Interval press ENTER button to confirm the interval time will show on BRITEQ 16 BTX 700SW the display Press MENU button to exit Remain Time Select Remain Time press ENTER button to confirm the remaining time will show on the display press ENTER button to confirm use UP and DOWN button to select Exit or Reset time press MENU button to exit Factory Setting Select Factory Setting press ENTER button to confirm the fixture will reset to factory settings and exit menu mode 6 3 Home Position Adjustment Press MENU button into menu mode then press ENTER button for about 3 seconds into offset mode to adjust the home position Select the function by ENTER button Use UP and DOWN button to choose the submenu press the ENTER button to stor
18. button to adjust the address from 0 to 512 press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode Please refer to the following diagram to address your DMX512 channel for the first 4 units Channel mode Unit 1 Unit 2 Unit 3 Unit 4 Address Address Address Address 1 6 17 22 channels 7 4 DMX 512 Configuration Please refer to below configurations to control the fixtures Attention 1 The unit will maintain the last condition until reset if you cut off the DMX signal 2 For the channel Function keep the value for about 5 seconds then the corresponding function will take into effect 22 Channels mode 1 SETS LE 1 Pan Tilt 540 270 255 Slow unze 240 247 Random 204 239 Ee 166 203 Slow 132 167 Fast Close 232 16 131 44 2 8 15 Open 7 Blackout Fast 0 Blackou 255 Rotation Fast 255 255 255 100 194 Rotation Slow 190 193 Stop 189 Rotation Slow 128 Rotation Fast 064 127 Color Mix 056 063 Blue 048 055 Green 040 047 Pink 032 039 5600K 024 031 3200K 016 023 Orange 008 015 Red k 001 007 White BRITEQ 21 BTX 700SW BRITEQ 22 BTX 700SW 22Channels Mode 1 Ch12 Ch13 Ch14 Ch15 Ch16 234 255 Color11 213 233 Color10 192 212 Color9 171 191 Color8 149 170 Color7 128 148 Color6 107 127 Color5 086 106 Color4 064 085 Color3 043 063 Color2 0
19. damage or interference to DMX interface circuit C One of the channels is not working well 1 The stepper motor might be damaged or the cable connected to the PCB is broken 2 he motor s drive IC on the PCB might be out of condition BRITEQ 28 BTX 700SW The lamp is cutting out intermittently The lamp is not working well Check the mains voltage either too high or too low 2 Internal temperature may be too high Check if replacement of fan is needed on the head E If The pan belt is broken 1 Turn off the mains power 2 Loosen the screws A open the cover B 3 Loosen the screws C 4 5 Unplug all the connect wires over the belt Change a new belt D put the belt around the axis gear and motor gear 6 Plug all the connect wires back upon the belt Tighten all the screws F If The tilt belt is broken 1 Turn off the mains power 2 Loosen all the screws A and open the right arm cover B 3 Loosen the screws C that fix the bridge 4 Change a new belt D Please adjust the tension of the belt properly Note do not fix the belt too tight as itis can easily rupture 5 Reverse the procedures from step 3 to 2 10 Maintenance and Cleaning Maintenance Ignitor Ballast Filter A As the pictures shown above please replace the cable or cable joints immediately once they ve turned yellow B Do maintain the fixtures every two months and make sure that all the screws and terminals hav
20. de select DMX Functions press ENTER button to confirm use UP and DOWN button to select DMX Address DMX Channel Mode View DMX Value or WDMX Setting DMX Address DMX512 address setting Select DMX Address press ENTER button to confirm the present address will blink on the display use UP and DOWN button to adjust the address from 0 to 512 press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode DMX Channel Mode channel mode Select DMX Channel Mode press ENTER button to confirm present channel mode will blink on the display use UP and DOWN button to select Mode1 22 channels mode or Mode 2 22 channels mode or Mode 3 29 channels mode press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode View DMX Value Select View DMX Value press ENTER button to confirm Channel function and its value will show on the display use UP and DOWN button to view other DMX value Press MENU button back to the last menu or let the unit idle one minute to exit menu mode WDMX Setting wireless control setting For the unit with wireless receiver built in only Select WDMX Setting press ENTER button to confirm Use UP and DOWN button to select Active Retransmit or Reset Memory press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode BRITEQ m
21. e and automatically return to the last menu Press MENU button to exit Pan H 128 127 Pan pan home position adjust Enter offset mode Select Pan press ENTER button to confirm the present position will blink on the display use UP and DOWN button to offset the value from 128 to 127 press ENTER button to store Press MENU button to exit Tilt Tilt home position adjust Enter offset mode Select Tilt press ENTER button to confirm the present position will blink on the display use UP and DOWN button to offset the value from 128 to 127 press ENTER button to store Press MENU button to exit BRITEQ 17 BTX 700SW Shutter Shutter home position adjust Enter offset mode Select Shutter press ENTER button to confirm the present position will blink on the display use UP and DOWN button to offset the value from O to 255 press ENTER button to store Press MENU button to exit Dimmer Dimmer home position adjust Enter offset mode Select Dimmer press ENTER button to confirm the present position will blink on the display use UP and DOWN button to offset the value from 0 to 255 press ENTER button to store Press MENU button to exit Color Color home position adjust Enter offset mode Select Color press ENTER button to confirm the present position will blink on the display use UP and DOWN button to offset the value from 128 to 127 press ENTER button to store Press MENU button to exit Cyan Cyan home position adjus
22. e been locked firmly to make sure the normal performance of the fixtures Negligence of maintenance would cause malfunction of the fixture Cleaning The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s optics Clean with soft cloth and use normal glass to clean fluid Always dry the parts carefully Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days BRITEQ 29 BTX 700SW
23. en to operate the fixture Use safety chain when fixing the unit Handle the unit by carrying its base instead of head only e The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slots are blocked otherwise the unit will be overheated Before operating ensure that the voltage and frequency of power supply match the power requirements of the unit e It s important to ground the yellow green conductor to earth in order to avoid electric shock e Maximum ambient temperature TA 40 C Don t operate it when the temperature is higher Don t connect the device to any dimmer pack During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective and it will decrease gradually within 15 minutes e sure there are no flammable materials close to the unit while operating to avoid fire hazard Examine the power wires carefully replace them immediately if there is any damage Unit s surface temperature may reach up to 850 Don t touch the housing bare handed during its operation and allow about 15 minutes for cooling the unit down before replacing bulb or maintenance as it could be very hot e Avoid any inflammable liquids water or metal objects entering the unit Once it happens cut off the mains power immediately e Do not operate in dirty or dusty environment do clean f
24. ess MENU button back to the last menu or let the unit idle one minute to exit menu mode Ignition Delay Delay time between power on and lamp on Select Ignition Delay press ENTER button to confirm present mode will blink on the display use UP and DOWN button to adjust the delay time from OS to 2555 press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode Low Power Delay Delay time between reduce lamp power and shutter off the unit Select Low Power Delay press ENTER button to confirm present mode will blink on the display use UP and DOWN button to adjust the delay time from OS to 2555 press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode If you set the low power delay time to 3S the lamp will run in half power 3 seconds after the unit shutter off Display Setting Enter menu mode select Display Setting press ENTER button to confirm use UP and DOWN button to select Display Inverse Backlight Auto Off Backlight Intensity or Temperature unit Display Inverse Select Display Inverse press ENTER button to confirm present mode will blink on the display use UP and DOWN button to select No normal display or Yes inverse display press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode Backlight Auto Off Select Backlight Auto Off pre
25. impracticable press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode When you operate the unit via DMX controller set the value of channel special function to lamp off waiting for 5 seconds then the lamp will be off if you choose yes mode On If DMX On Lamp turns on when DMX signal is detected Select On If DMX On press ENTER button to confirm present mode will blink on the display use UP and DOWN button to select Yes Lamp turns on when DMX signal is detected or No keep the present state press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode f the lamp is off via DMX signal you can reconnect the DMX controller to make the lamp on BRITEQ 13 BTX 700SW Off If DMX Off Lamp turns off when DMX signal is cut off Select Off If DMX Off press ENTER button to confirm present mode will blink on the display use UP and DOWN button to select Yes Lamp turns off when DMX signal is cut off press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode Cooling Mode Lamp turns off when DMX signal is cut off Select Cooling Mode press ENTER button to confirm present mode will blink on the display use UP and DOWN button to select Auto fans speed adjust automatically or High fans run in high speed press ENTER button to store Pr
26. irm the present channel will show on the display use Up and DOWN button to select channel press ENTER button to confirm then use UP and DOWN button to adjust the value press ENTER button to store the fixture will run as the channel value indicates Press MENU button back to the last menu or exit menu mode idling one minute All channels value will become 0 after exiting Manual Test menu Fixture Information Enter menu mode select Fixture Information press ENTER button to confirm use UP and DOWN button to select Fixture Use Time Lamp On Time or Firmware Version Fixture Use Time Select Fixture Use Time press ENTER button to confirm fixture use time will show on the display press MENU button back to exit Lamp On Time Select Lamp On Time press ENTER button to confirm lamp on time will show on the display press ENTER button to confirm use UP and DOWN button to select Exit or Reset Time press ENTER button to confirm Press MENU button back to the last menu or exit menu mode let the unit idle one minute Firmware Version Select Firmware Version press ENTER button to confirm firmware version will show on the display press MENU button back to exit Reset Functions Enter menu mode select Reset Function press ENTER button to confirm use UP and DOWN button to select Pan Tilt Color CMY Gobo Shutter Dimmer Focus Zoom Prism Frost lris Flatb All BRITEQ 15 BTX 700SW Pan Tilt Reset Pan Tilt Select Pa
27. is 40 001 Present start address Yes Md 1 22Ch Present channel mode is mode 1 22 channels mode Yes 2 Warning signal blinking direct resetting error Yes On Off e Pegel 6 2 Main Function OFF Turn on the unit press MENU button into menu mode press UP and DOWN button until the 1 State PowerOn required function is shown on the monitor Select the function by ENTER button Use UP SITE OffViaDmx and DOWN button to choose the submenu press the ENTER button to store and automatically return to the last menu Press MENU button or let the unit idle one minute to one Se In the event of disconnecting with mains power press UP button for one minute to enter into menu mode Press MENU button or let the unit idle one minute to exit Yes Auto t The main functions are shown below the grayed boxes are preset settings Ig Display Inverse es Backlight Auto Off BEIC ET 65 Backlight Intensity 1 10 Temperature Unit Auto Test Z n 00 Manual Test Fixture use time Exit Lamp On time eset lime Fireware Version BRITEQ 9 BTX 700SW BRITEQ 10 BTX 700SW No Pan Tilt Yes e Mace Color CMY R eset Functions Shutter Dimmer Yes No lris Flatb a Ges d All No Al No Fixture Maintenance 7 Special Functions Factory Setting es DMX Functions Enter menu mo
28. ixtures regularly e Do not touch any wire during operation as there might be a hazard of electric shock e Avoid power wires together twist other cables e he minimum distance between light output and the illuminated surface must be more than 2 5 meters e Disconnect mains power before fuse lamp replacement or servicing e Replace fuse lamp only with the same type e Inthe event of serious operating problem stop using the unit immediately e Never turn on and off the unit time after time e The housing the lenses or the ultraviolet filter must be replaced if they are visibly damaged BRITEQ 1 BTX 700SW e Do not open the unit as there are no user serviceable parts inside e Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center if needed e Disconnect the mains power if the fixture is has not been used for a long time e Do use the original packing materials before transporting it again Caution e prevent or reduce the risk of electrical shock or fire do not expose the unit to rain moisture e Hot lamp explosion hazard Do not open the unit within 15 minutes after switching off e Do replace the bulb once it is damaged deformed or life expired e Do not look directly at the light while the bulb is on e Never touch bulb with bare fingers as it is very hot after using Do not s
29. n Tilt press ENTER button to confirm use UP and DOWN button to select Yes the unit will run built in program to reset pan and tilt to their home positions or No press ENTER button to store Press MENU button to exit Color CMY Reset Color CMY Select Color CMY press ENTER button to confirm use UP and DOWN button to select Yes the unit will run built in program to reset color and CMY to their home positions or No press ENTER button to store Press MENU button to exit GOBO Reset GOBO Select GOBO press ENTER button to confirm use UP and DOWN button to select Yes the unit will run built in program to reset GOBO wheel to their home positions or No press ENTER button to store Press MENU button to exit Shutter Dimmer Reset Shutter Dimmer Select Shutter Dimmer press ENTER button to confirm use UP and DOWN button to select Yes the unit will run built in program to reset shutter and dimmer to their home positions or No press ENTER button to store Press MENU button to exit Focus Zoom Prism Frost Reset Focus Zoom Prism Frost Select Focus Zoom Prism Frost press ENTER button to confirm use UP and DOWN button to select Yes the unit will run built in program to reset focus zoom prism and frost to their home positions or No press ENTER button to store Press MENU button to exit lris Flatb Reset Iris Flatb Select Iris Flatb press ENTER button to confirm use UP and DOWN button to select Yes the unit will run
30. nd DOWN button to select No normal or Yes tilt inverse press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode P T Feedback pan tilt Feedback Select P T Feedback press ENTER button to confirm present mode will blink on the display press UP DOWN button to select No Pan or tilts position will not feedback while out of step or Yes Feedback while pan tilt out of step press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode BL O P T Moving Blackout while pan tilt moving Select BL O P T Moving press ENTER button to confirm present mode will blink on the display use UP and DOWN button to select No normal while pan tilt moving or Yes blackout while pan tilt moving press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode BL O Color Change Blackout while change color Select BL O Color Change press ENTER button to confirm present mode will blink BRITEQ 12 BTX 700SW the display use UP and DOWN button to select No normal while changing color or Yes blackout while change color Press MENU button back to the last menu or let the unit idle one minute to exit menu mode BL O Gobo Change Blackout while change gobo Select BL O Gobo Change press ENTER button to confirm present mode will blink on the display use U
31. ocus home position adjust Enter offset mode Select Focus press ENTER button to confirm the present position will blink on the display use UP and DOWN button to offset the value from 0 to 255 press ENTER button to store Press MENU button to exit Zoom Zoom home position adjust Enter offset mode Select Zoom press ENTER button to confirm the present position will blink on the display use UP and DOWN button to offset the value from O to 255 press ENTER button to store Press MENU button to exit 6 4 Error Information Lamp Startup Fail It appears when there is no lamp or some wires are damaged Temperature Sense Error It appears when temperature check board is damaged Lamp Too Hot Power Off It appears when temperature is detected higher than 110 C Check if the unit is properly ventilated or fans or temperature check board may is damaged Lamp Too Hot Low Power It appears when detected temperature is over 105 C the unit will run on a low power level Maintenance Fixture It appears when the maintenance remaining time becomes OS please enter menu mode and reset the time Lamp On Over 700 Hour It appears when the lamp has been on over 700 hours please turn off the lamp Memory Initial Fail It appears when the memory IC is damaged CPU B Error CPU C Error CPU D Error They appear when board P C or some wires are damaged Pan Reset Error Pan Encode Error Tilt Reset Error Tilt Encode Error Shutter Reset
32. put connectors are pass through to maintain the DMX circuit when one of the units power is disconnected 4 Each lighting unit needs to have a DMX address to receive the data by the controller The address number is between 0 511 usually O amp 1 are equal to 1 5 The end of the DMX 512 system should be terminated to reduce signal errors 6 3 pin XLR connectors are more popular than 5 pins XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal Pin4 Pin5 not used BRITEQ 20 BTX 700SW 7 2 Channel Mode Setting Enter menu mode select DMX Functions press ENTER button to confirm use UP and DOWN button to select DMX Channel Mode press ENTER button to confirm present channel mode will blink on the display use UP and DOWN button to select Mode1 22 channels mode or Mode 2 22 channels mode or Mode 3 29 channels mode press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode 7 3 Address Setting If you use a universal DMX controller to control the units you have to set DMX address from 1 to 512 so that the units can receive DMX signal Press MENU button to enter menu mode select DMX Functions press ENTER button to confirm use UP and DOWN button to select DMX Address press ENTER button to confirm the present address will blink on the display use UP and DOWN
33. sition To unlock the head press the tilt unlock button 5 and move the pan lock unlock lever 6 to unlock position Caution The head and arm must be unlocked before operation 4 2 Control Panel Front view Rear view O 1 Monitor Batter Back up display O 2 LED DMX On DMX input present O 3 Button MENU To enter into move backward or leave the menu A UP To go backward to move up in the menu V DOWN To move down in the menu ENTER To perform the desired functions O 4 Antenna optional Receive wireless signal from a wide range 5 DMX input output For DMX 512 operation use 3 5 pin XLR plug cable to link the units together O 6 Power Switch Turns On Off the power O 7 Power Cable To connect to the mains supply O 8 Fuse T 15 A Protect the unit from damage of over current BRITEQ 6 BTX 700SW WHEEL 1 replaceable GOBO WHEEL 2 DANGER Install the gobos with the device switched off only Unplug from mains before changing gobos CAUTION Never unscrew the screws of the rotating gobo as the ball bearing will otherwise be opened Please follow the steps below to insert change rotating gobos 1 Open the cover by loosening the fastening screws on the cover 2 Push the gobo plate follow the direction 1 and gently pull out the plate follow the direction 2 3 Take out the ring with an appropriate tool Do not touch the surface of the
34. ss ENTER button to confirm present mode will blink on the display use UP and DOWN button to select No display always on or Yes display goes off one minute after exiting menu mode press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode Backlight Intensity Select Backlight Intensity press ENTER button to confirm present mode will blink on the display use UP and DOWN button to adjust backlight intensity from 1 dark to 10 bright press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode BRITEQ 14 BTX 700SW Temperature Unit Select Temperature Unit press ENTER button to confirm present mode will blink on the display use UP and DOWN button to select C or F press ENTER button to store Press MENU button back to the last menu or let the unit idle one minute to exit menu mode Fixture Test Enter menu mode select Fixture Test press ENTER button to confirm use UP and DOWN button to select Auto Test or Manual Test Auto Test Select Auto Test press ENTER button to confirm the unit will run built in programs to automatically test pan tilt color CMY gobo gobo rotation shutter dimmer prism prism rotation frost zoom iris focus flatb and lamp on off Press MENU button back to the last menu or exit menu mode after auto test Manual Test Select Manual Test press ENTER button to conf
35. t Enter offset mode Select Cyan press ENTER button to confirm the present position will blink on the display use UP and DOWN button to offset the value from 0 to 255 press ENTER button to store Press MENU button to exit Magenta Magenta home position adjust Enter offset mode Select Magenta press ENTER button to confirm the present position will blink on the display use UP and DOWN button to offset the value from 0 to 255 press ENTER button to store Press MENU button to exit Yellow Yellow home position adjust Enter offset mode Select Yellow press ENTER button to confirm the present position will blink on the display use UP and DOWN button to offset the value from O to 255 press ENTER button to store Press MENU button to exit Gobo 1 Gobo 1 home position adjust Enter offset mode Select Gobo 1 press ENTER button to confirm the present position will blink on the display use UP and DOWN button to offset the value from 128 to 127 press ENTER button to store Press MENU button to exit R Gobo 1 Gobo 1 rotation home position adjust Enter offset mode Select R Gobo 1 press ENTER button to confirm the present position will blink on the display use UP and DOWN button to offset the value from 128 to 127 press ENTER button to store Press MENU button to exit Gobo 2 Gobo 2 home position adjust Enter offset mode Select Gobo 2 press ENTER button to confirm the present position will blink on the display use UP and D
36. tart on the unit without bulb enclosure or when housing is damaged Product Items e User manual e 2x Omega clamps 2 Installation Unpacking the fixture for flight case pack only 1 Stop the flight case via the brake sheet above the wheels 2 Unlock the lock modules 1 and open the cover board 3 Prop the cover board with lid bracket 4 Take out the fixture 5 Unlock the lock module 2 take out omega clamps Installation 1 Bolt each clamp 1 to the Omega holder with screw and lock nut through the hole in the holder 2 Fasten the omega holders 2 on the bottom of the base by inserting quick lock fasteners 3 into the holes of the base and tighten fully clockwise 3 Hang the fixture to the support 4 through clamp and fasten the screws 5 Fasten the safety cable 6 through the bottom of the base and over the support SS 1 Attention e Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit s weight BRITEQ 2 BTX 700SW Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating The equipment must be fixed by professionals And it must be fixed at a place where is out of the touch of people and has no one pass by or under it 3 Technical Specification Power supply 1
Download Pdf Manuals
Related Search