Home
Gotharman`s TubaZ
Contents
1. Mount TubaZ in your Eurorack case using screws Connecting With Other Modules The usual way og connecting TubaZ would be to connect an audio source to Audio In connecting Audio Out to another audio input and connecting modulation sources to the 4 CV inputs but this is modular so please feel free to experiment It is though not recommended to connect 2 or more outputs to each other The only output on TubaZ is the Audio Out All other connections are inputs Maximum ratings In case you connect your TubaZ to something outside your Eurorack system you should take care that these ratings are not exceeded Audio Input Should not exceed 12 volts CutOzzz CV 1 and 2 Max 30 volts total Rezo and Drive CV s Max 60 volts each Gotharman July 2014 www gotharman dk
2. Sotharmart s Tubaz 12 dB Tube Bandpass Filter Eurorack Module E Rezo TY 3 Sotharmar s se Ek NI Ch Mudio el CH t wt LJAer fYlanusal Thank you very much for purchasing consider to purchase my TubaZ eurorack module Please read this manual before setting up your TubaZ to avoid malfunction caused by wrong handling TubaZ are a 12 dB tube bandpass filter with the controls CutOzzz Rezonanz and Drive CV control are possible of all 3 parameters I designed it with the purpose of adding crunch edge and distortion to my eurorack system It is not an ideal bandpass filter that cuts off all frequencies above and below the center frequency Because of its high drive there are in most cases some bleedthrough of the harmonics that should have been cutted off You might consider calling it a Band Add filter The main purpose of it was to add edge not to be a perfect bandpass filter CutOzzz controls the center frequency of the filter Harmonics at frequencies above and below the cutozzz frequency are cutted off with a slope of 12 dB Because of the structure of this filter there might be some bleedthrough of frequencies that should have been cutted oft Rezonanz controls the sharpness of the filter Drive controls the input level of the audio signal going through the filter At higher settings this will cause the filter to distort depending on the level of the input signal Tube VCO mo
3. de When nothing is connected to the Audio input of TubaZ a feedback loop is formed that makes TubaZ act as a tube VCO This is not tuned to 1V oct or anything else but in can make some odd sounds CutOzzz controls the VCO frequency Rezonanz controls the sharpness of the sound Drive controls the harmonic contents of the sound Preparing TubaZ When you receive your TubaZ a strip of bubble wrap will be attached to it to protect the tube Remove this carefully by cutting it with a pair of scissors in one of the sides between the faceplate and the PCB and carefully lift it off e a Connecting The Power Cable TubaZ should be installed in a Eurorack case It requires 18 HP of space 12 volts DO NOT connect it to any other voltage than this as it might damage the tube 94 mA current Connections to other Eurorack modules using minijack cables The power connector of TubaZ at the upper right corner of the PCB is marked with 12V at m end of the connector facing upwards Zelt This is pin 1 and the 12 volt from your Eurorack power board should be connected to this pin If your TubaZ came with a multicoloured 16 cored flat cable the brown core should be placed at pin 1 If it came with a grey red cable the red core should be connected to pin 1 Mount the other end of the power cable to the powerboard of your Eurorack case Make sure that pin 1 is connected to 12 volt
Download Pdf Manuals
Related Search
Related Contents
Massive Table lamp 43227/43/10 Table des matières Samsung 920NW User Manual 着ぐるみ取扱説明書 - JCCCA 全国地球温暖化防止活動推進センター Targus TSS112EU en français - XL-Nord Community Area Profiles: User Guide Blaupunkt GTb 8200 A Dot-app User Guide Copyright © All rights reserved.
Failed to retrieve file