RC702 (C) User Manual
Contents
1. gt Start Hyper Terminal software on management station and configure the interface property as below Port Settings Bits per second ISS Data bits fe y Parity None y Stop bits i Flow control Hardware zl Restore Defaults Cancel gt Configure RC702 management information Refer to RC702 Software Configuration Guide and RC702 Command Notebook for details 6 2 8 Applying power supply If using DC 48V power supply connect the ground pin to protecting ground PGND Before turning on the power supply connect 48V pin to the low voltage cord and BGND pin to the high voltage cord Firmly connected and ensure there is no short circuit then turn on the power supply If using AC 220V power supply directly use the power cord shipped with the device After connecting power supply PWR indicator shall be ON When SYS indicator on the front panel begins to flash the device has finished initialization Note 1 RC702 GE Ethernet interface fiber copper only supports 1000M full duplex mode If connected with another 10 100M device it will not be able to LINK and will not work Page 16 of 20 Appendix A Abbreviations STM 1 SDH GFP LAPS LACS EOS Synchronous Transport Module N Synchronous Digital Hierarchy Generic Framing Protocol Link Access Procedure SDH Link Capacity Adjustment Scheme Ethernet over SDH Page 17 of 20 Appendix B FAQ If you e2. Windows NT is a U S registered trademark of Microsoft Corporation Windows 2000 is a U S registered trademark of Microsoft Corporation Windows XP is a U S registered trademark of Microsoft Corporation Windows and MS Windows are U S registered trademarks of Microsoft Corporation Contact Information Technical Assistance Center The Raisecom TAC is available to all customers who need technical assistance with a Raisecom product technology or solution You can communicate with us through the following methods Add 1120 Haitai Tower 229 Fourth North Loop Middle Road Haidian District Beijing 100083 Tel 86 10 82884499 Ext 878 International Department Fax 86 10 82885200 86 10 82884411 World Wide Web Feedback You can access the most current Raisecom product information on the World Wide Web at the following URL http www raisecom com Comments and questions about how Raisecom equipment works are welcomed Please review the FAQ in the related manual and if your question is not covered send email by using the following web page http www raisecom com en xcontactus contactus htm If you have comments on Raisecom equipment and solutions instead of the web page above please send comments to export raisecom com We hope to hear from you CONTENTS 2EINVOVERVIEWE aan seed eel pecan Seege ut eis rn as oben save ee Buea fee Roady 7 2 2s MAIN FEATURES sti da dd belassen Bcn lt rah tied
3. 2 rear panel Page 13 of 20 Chapter 5 Function and Application 5 1 Basic Principle of RC702 The basic principle of RC702 is Ethernet interface received frames will be GFP LAPS encapsulated and mapped into corresponding VCG 1 VC4 N VC3 N VC12 and transmitted through SDH MSTP network to the other end At the other end RC702 will extract original Ethernet frames from GFP LAPS encapsulation and output them to Ethernet interface 5 2 Basic Applications RC702 basic application is depicted in Figure 5 1 SDH equipment Figure 5 1 RC702 typical application Page 14 of 20 Chapter 6 Installation and Inspection 6 1 Preparation First check the type and amount of the device with packing list and the appearance There must be drying process if the device is affected by damp environment To make sure the device will work normally please follow the steps Read the user manual carefully Prepare fiber optic and Ethernet cable Fix and install access device Connect fiber and cable Configure the device For configuring details refer to software configuration guide Vv VV VV WV Use normally 6 2 Installation Process 6 2 1 Preparing cables Necessary cables are listed below Interface Cable specifications EECHER Eo interface and SNMP 100BaseTX CATS UTP cable max 100m User prepares Console table Refer to Annex for console cable making One console cable is provided with accessory 155M SDH copper in
4. C702 1 SDH 155M interface optional fiber copper 1 Fast Ethernet interface optional fiber copper RC702 GE 1 SDH 155M interface optional fiber copper 1 Gigabit Ethernet interface optional fiber copper Power supply cards 220V AC or 48V DC dual power supply redundant V VV WV Management port console port and SNMP port 3 2 SDH Fiber Interface Specification Speed 155 52Mbps Line code NRZ Connector type SC Vv VV WV Refer to Table 2 1 for other parameters 3 3 SDH Copper Interface Specification gt Speed 155 52Mbps gt Line code CMI compliant to G 703 standard gt Connector type BNC 3 4 100M 1000M Ethernet Copper Interface Specification Fast Ethernet 10 100M auto negotiation Gigabit Ethernet 1000M full duplex Connector type RJ45 Compliant to IEEE802 3 standard Support VC4 VC3 and VC12 concatenation Support LCAS under VC3 and VC12 virtual concatenation WV VV VV Y Support GFP and LAPS encapsulation Note VC3 and VC12 concatenations are not implemented on this version 3 5 100M 1000M Ethernet Fiber Interface Specification gt Fast Ethernet 100M full duplex Gigabit Ethernet 1000M full duplex gt Connector type SC gt Refer to Table 2 1 for other parameters Page 9 of 20 Support VC4 VC3 and VC12 concatenation Support LCAS under VC3 and VC12 virtual concatenation Support GFP and LAPS encapsulation Yv V V WV Note VC3 and VC12 concatenations are not implemented on this
5. Co Matti dake gege tel co na ege 7 23 PRODUCT PART NUMBER INTRODUCTION 225006 4 20 22 da caddie Gina ees 7 ZA DIMENSION SHA eiii Baal deceo do de sed ad Dardo coda o ce el ea ease ell Do E iss 8 CHAPTER3 TECHNICAL SPECIFICATION zussesneoneneonennenesnenneneonennenesnennenesnennenesnennesennennenesnennenennennenesnennesesnennesennenne 3 6 CONSOLE PORT PROPERTIES 3ST SNMP PORT PROPERTIES ni 3 8 POWER SUPPLY 3 9 WORKING ENVIRONMENT CHAPTER 4 CONSTRUCTION AND INDICATORS s sesesesesesesesososososesosososososososososososososososososesosesosososesesosesesesese LI A INERONEPANB EE 4 2 REAR PANEL INTRODUCTION CHAPTER5 FUNCTION AND APPLICATION zussessessesesneneneonennenesnennenesnennenesnennenesnennenesnennenennennesennennenesnennenesnenneseenene LF 5 1 BASIC PRINCIPEE OF RC 7 02 cid es Co Sea ohh sk dae A it obte 14 5 2 B ASIC APPLICATIONS eh east a Bee cae NOSES se ef ee deed caves E cE 14 CHAPTER6 INSTALLATION AND INSPECTION cscsssssssssssssssessessssessessssessessssessessssessessssessessssessessssessessssessesssses LO ANAIS O A OOO NR Sege 15 EE NEE 15 6 2 1 Preparing Cables iii a A A eege deed ests 15 6 2 2 Connect 155M SDH fiber Interface 15 6 2 3 Connect 155M SDH copper interface sccccesccscssecsessessesseeseescesecssesecsseescsseescesecaeesecsaeseesaecseesecaaesecnaseeeeaseaeeaecateneeneeees 15 6 2 4 Connect Ethernet fiber interface ccccsccssssecssscssesecnseescsseesc
6. RA SECOM D www raisecom com z RC702 C User Manual June 2006 Legal Notices Warranty Raisecom Technology Co Ltd makes no warranty of any kind with regard to this manual including but not limited to the implied warranties of merchantability and fitness for a particular purpose Raisecom Technology Co Ltd shall not be held liable for errors contained herein or direct indirect special incidental or consequential damages in connection with the furnishing performance or use of this material A copy of the specific warranty terms applicable to your Raisecom product and replacement parts can be obtained from Service Office Restricted Rights Legend All rights are reserved No part of this document may be photocopied reproduced or translated to another language without the prior written consent of Raisecom Technology Co Ltd The information contained in this document is subject to change without notice Copyright Notices Copyright 2006 Raisecom All rights reserved No part of this publication may be excerpted reproduced translated or utilized in any form or by any means electronic or mechanical including photocopying and microfilm without permission in Writing from Raisecom Technology Co Ltd Trademark Notices RAISECOM is the trademark of Raisecom Technology Co Ltd Java is a U S trademark of Sun Microsystems Inc Microsoft is a U S registered trademark of Microsoft Corporation
7. a 100083 Phone 8610 82884499 WV T Ih Hh FR JA it RR E B BR a D Fax 8610 82885200 Http www raisecom com Email export raisecom com RAISECOM TECHNOLOGY CO LTD Technical Support 8610 82883305 Km S Page 20 of 20
8. bit s hierarchy G 825 The control of jitter and wander within digital networks which are based on the synchronous digital hierarchy SDH G 826 End to end error performance parameters and objectives for international constant bit rate digital paths and connections G 828 Error performance parameters and objectives for international constant bit rate synchronous digital paths G 829 Error performance events for SDH multiplex and regenerator sections G 831 Management capabilities of transport networks based on the synchronous digital hierarchy SDH G 841 Types and characteristics of SDH network protection architectures G 842 Interworking of SDH network protection architectures G 957 Optical interfaces for equipments and systems relating to the synchronous digital hierarchy G 691 Optical interfaces for single channel STM 64 and other SDH systems with optical amplifiers G 664 Optical safety procedures and requirements for optical transport systems 1 731 ATM Types and general characteristics of ATM equipment 1 732 ATM Functional characteristics of ATM equipment IEEE 802 1Q Virtual Local Area Networks LANs IEEE 802 1p Traffic Class Expediting and Dynamic Multicast Filtering IEEE 802 3 CSMA CD Access Method and Physical Layer Instruction Related Manuals RC702 C User Manual RC702 C Software Configuration Guide RC702 C Command Notebook RC702 EMS User Manual Chapter 2 Product Overview 2 1 Overview RC702 FE RC702 GE dev
9. e VC3 and VC12 concatenations are not implemented on this version 2 3 Product Part Number Introduction RC702 device is composed of main board expansion card and power supply card Expansion cards can be divided into SDH fiber interface card SDH copper interface card Fast Ethernet fiber interface card Fast Ethernet copper interface card Gigabit Ethernet fiber interface card and Gigabit Ethernet copper interface card 1 Part number RC702 X RC702 GE X Introduction RC702 stands for Raisecom EOS equipment series GE stands for Gigabit Ethernet interface Page 7 of 20 X stands for the power supply type Could be AC 220V or DC 48V 2 Expansion card part number introduction Part number Introduction RC702 SC OP X SDH fiber interface card providing 1 STM 1 SDH fiber interface X stands for fiber interface type could be M 1 52 53 13 15 5523 S25 Refer to Table 2 1 for details RC702 SC EP SDH copper interface card providing 1 STM 1 SDH copper interface BNC connector RC702 SC FE Fast Ethernet card providing 1 10 100M Ethernet copper interface RC702 SC FX X Fast Ethernet card providing 1 100M full duplex Ethernet fiber interface X stands for fiber interface type could be M 51 52 53 13 15 5523 525 Refer to Table 2 1 for details Gigabit Ethernet card providing 1 1000M full duplex Ethernet fiber interface SC200 GE X X stands for fiber interface typ
10. e could be M 51 52 53 13 15 5523 5525 Refer to Table 2 1 for details SC200 GE T Gigabit Ethernet card providing 1 1000M full duplex Ethernet copper interface 3 Power supply card part number introduction Part number Introduction RC 702 PWR AC AC 220V RC 702 PWR DC DC 48V Table 2 1 Fiber Interface Specification Data S Launch RX Extinction Minimum Estimated Ga SE speed IL En power sensitivity ratio Saturation TX distance p Mbps dBm dB dB dbm km M sc 15552 NRZ 1310 18 14 lt 29 38 2 gt 14 0 2 Multimode ei SE 155 52 NRZ 1310 ase ea 38 2 gt 8 0 25 52 ee 155 52 NRZ 1310 Sa lt 34 gt 8 2 gt 8 10 60 53 on 155 52 NRZ 1550 DFB 5 0 lt 36 gt 10 gt 10 15 120 SC Single 5513 strand single 155 52 NRZ A110 19 3 lt 30 gt 8 2 gt 8 0 25 RX 1550 mode SC single 5515 strand single 155 52 NRZ III 19 3 lt 30 3 2 gt 8 0 25 RX 1310 mode SC S ingle 5523 strand single 155 52 NRZ 1310 5 0 lt 32 38 2 gt 8 10 50 RX 1550 mode SC single 5525 strand single 155 52 NRZ e Bai lt 32 3 2 gt 8 10 50 mode Note Single strand devices must be deployed in pairs 2 4 Dimensions RC702 adopts standard 19 chassis in a compact metal enclosure Dimensions 440mm width x 43 6mm height x 235mm depth Page 8 of 20 Chapter 3 Technical Specification 3 1 Basic Configuration R
11. esecseesecasesecsseescsaeeseusecseesecsaescessecsesecaeesecuaeeeeaseseeaesaeesesneeees 15 6 2 5 Connect Ethernet copper interface ursuesuessesuenesnensernersensnenonnnesnensenonsersnnsonnnenensesnonsensansonsnenenennonsensansonsesnnesnonaen 16 6 2 0 TE 16 6 2 7 COMNECt CONSOLE port uti iii dc dia dilata 16 6 2 8 Applying power SUppLy coi tdi liinda dada adidas 16 APPENDIX C CONSOLE CABLE MAKING eseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseseses LD Revision Chapter 1 Preface This manual is for the latest RC702 Ethernet over SDH equipment Revision C About This Manual This manual introduces primary functions of the configuration management software for RC series products Who Should Read This Manual Compliance Sales and marketing engineers after service staff and telecommunication network design engineers could use this manual as a valuable reference If you want to get an overview on features applications architectures and specifications of Raisecom RC series integrated access devices you could find useful information in this manual as well The RC series products developed by Raisecom are strictly complied with the following standards as well as ITU T IEEE IETF and related standards from other international telecommunication standard organizations YD T900 1997 SDH Equipment Technical Requirements Clock YD T973 1998 SDH 155Mb s and 622Mb s Tec
12. hnical conditions of optical transmitter module and receiver module YD T1017 1999 Network node interface for the Synchronous Digital Hierarchy SDH YD T1022 1999 Requirement of synchronous digital hierarchy SDH equipment function YD T1078 2000 SDH Transmission Network Technique Requirements Interworking of Network Protection Architectures YD T1111 1 2001 Technical Requirements of SDH Optical Transmitter Optical Receiver Modules 2 488320 Gb s Optical Receiver Modules YD T1111 2 2001 Technical Requirements of SHD Optical Transmitter Optical Receiver Modules 2 488320 Gb s Optical Transmitter Modules YD T1179 2002 Technical Specification of Ethernet over SDH G 703 Physical electrical characteristics of hierarchical digital interfaces G704 Synchronous frame structures used at 1544 6312 2048 8448 and 44 736 kbit s hierarchical levels G 707 Network node interface for the synchronous digital hierarchy SDH G 774 Synchronous digital hierarchy SDH Management information model for the network element view G 781 Synchronization layer functions G 783 Characteristics of synchronous digital hierarchy SDH equipment functional blocks G 784 Synchronous digital hierarchy SDH management G 803 Architecture of transport networks based on the synchronous digital hierarchy SDH G 813 Timing characteristics of SDH equipment slave clocks SEC G 823 The control of jitter and wander within digital networks which are based on the 2048 k
13. ices are Raisecom self developed Ethernet over SDH equipment RC702 FE provides a 155M SDH interface either fiber or copper and a 100M Ethernet interface either fiber or copper RC702 GE provides a 155M SDH interface either fiber or copper and a 1000M Ethernet interface either fiber or copper Using RC702 Ethernet over SDH equipment Ethernet data frames are directly encapsulated into SDH payload and transmitted across the SDH infrastructure It adopts standardized encapsulation technology and is compliant to relevant SDH standards Its network manageability has enabled it to be managed conveniently and easily It has already been widely deployed in carriers networks 2 2 Main features Provide 1 STM 1 interface with optional fiber or copper interface Provide 1 100M or 1000M Ethernet interface with optional fiber or copper interface Support VC4 VC3 and VC12 concatenation flexibly allocating service bandwidth Support LCAS function under VC3 and VC12 concatenation Support GFP and LAPS Ethernet encapsulation Configurable local clock or following line clock compliant to G 813 standard Vv Vv VV VV Y Provide console port and SNMP interface and ECC embedded channel Support local and remote online software upgrade convenient for maintenance gt Provide complete alarm indication and performance monitoring gt Provide dependable dual power supplies Power consumption is less than 20 Watts gt Working temperature 5 50 C Not
14. ncounter problems during installation and deployment please try the following solutions However if problems persist please contact your local distributors or Raisecom for technical support 1 The green PWR indicator is OFF Answer the device is not properly connected with power supply or power supply fails 2 There is LOS alarm at SDH fiber copper interface Answer it indicates SDH fiber copper signal loss First check if fiber copper cable is properly connected second use fiber optic attenuator may be needed coaxial to loopback third change a new fiber optic copper If the problem persists it is likely that the device is faulty 3 Ethernet interface or SNMP port LNK ACT indicator is OFF Answer first check if the cable is disconnected Then check if Ethernet interface or SNMP port connected device is working properly speed matching Confirm if the wire order is correct Page 18 of 20 Appendix C Console Cable Making One end of console cable is RJ45 connector connected to RC702 device the other end is DB9 connector connected to management station The pin configuration is listed in below table means RJ45 pin is not connected DB9 pin that not listed is not connected RJ 45 pin number Definition DB9 pin number 1 NC 2 DSR 6 3 RxD 3 4 GND 5 5 GND 5 6 TxD 2 7 DTR 4 8 NC Page 19 of 20 E m IN Address 620 Haitai Tower Haidian District Beijing Chin
15. terface BNC connector 750hm coaxial cable and max 100m User prepares 155M SDH fiber interface and Ethernet fiber SC SC or SC FC connector single mode or multimode patch cord depending interface on user s requirement AC 200V 10A power cord DC 48V 48V 10A power cord Table 5 1 RC702 interface cable specification Power supply socket 6 2 2 Connect 155M SDH fiber interface gt Connect the prepared fiber patch cord to SDH interface gt LOS indicator shall be OFF if connecting correctly 6 2 3 Connect 155M SDH copper interface gt Connect the prepared 75Ohm coaxial cable to SDH interface gt LOS indicator shall be OFF if connecting correctly 6 2 4 Connect Ethernet fiber interface gt Connect prepared fiber patch cord to Ethernet fiber interface Page 15 of 20 gt LNK ACT indicator shall be ON if connecting correctly Note 1 6 2 5 Connect Ethernet copper interface One end of Ethernet cable shall be connected to Router or Ethernet Switch and the other end shall be connected to Ethernet copper interface LNK ACT indicator shall be ON if connecting correctly Note 1 6 2 6 Connect SNMP port Connect SNMP port and relevant management station with Ethernet cable LNK ACT indicator shall be ON if connecting correctly 6 2 7 Connect console port gt Connect the console cable s RJ45 head to the console port of RC702 gt Connect the console cable s DB8 head to the COM port of management station
16. version 3 6 Console Port Properties gt Connector type RJ45 gt Compliant to RS 232 standard gt Speed 9600bps 3 7 SNMP Port Properties Connector type RJ45 Compliant to IEEE802 3 standard 10 100M auto negotiation WV V V WV Host mode pin order supporting auto MDI MDIX 3 8 Power Supply gt Power voltage DC 48V tolerance 72 36V AC 220V tolerance 180 260V gt Power consumption less than 20W 3 9 Working Environment gt Temperature 5 50 C gt Relative humidity lt 90 35 C Page 10 of 20 Chapter 4 Construction and Indicators 4 1 Front Panel RAISECOM RC702 vena AN Ze P WM nd q om u COMBLE mas wi RAISECOM RCTO2 Low ALM Ge m m KT us ra IL wo par COMBLE MAS PAR RAISECOM RC102 ACT am te O Il Oc bd CE um a Cona ws mwa RAISECOM RC702 ACT am on LKE wa CONBLE Wa Wa m Dao HA SECOM RCi02 LACH KE WWW c m sm CONELE wes FU Page 11 of 20 Note RC702 and RC702 GE adopt the same hardware structure except for Ethernet expansion card DE gt UNKYACT so c Indicator Number Item color Description 1 5 mn carg Number 1 and 2 swappable power supply optional AC220V and DC 48V 8 SDH card slot SDH interface fiber copper interface optional RC702 optional fiber copper 100M interface card 15 ne RC702 GE optional fiber copper 1000M interface card 24 Power suppl
17. y Number 1 and 2 power supply buttons switch button Green ON power up OFF power down 3 6 7 22 PWR indicator 3 and 6 indicates power supply cards power up 7 indicates SDH interface card power up 22 indicates the whole device power up Ke Red ON SDH interface signal loss 3 LOS indicator OFF SDH interface normal D Red ON SDH interface frame loss Y LOF indicator OFF SDH interface normal 111214 Ia SSES Indicates corresponding working speed respectively uw indicator Note RC702 GE only supports 1000M full duplex 15 24 Ethernet LNK ACT Green ON Ethernet interface status up link normal indicator Flashing transmitting receiving data 16 SNMP port 100M Green ON SNMP port works at 100M indicator OFF SNMP port works at 10M 17 SNMP port Green ON SNMP port status up link normal LNK ACT indicator Flashing transmitting receiving data at SNMP port 18 SNMP SNMP Ethernet port 19 CONSOLE Local console port connecting to PC COM port 20 MAS Green ON Master station OFF Slave station 21 ALM Red General alarm indicator Any alarm will generate ALM indicator 23 SYS en System indicator Flashing indicates CPU normal 25 E Green Fast Ethernet fiber interface indicator ON indicates fiber interface is 5D indicator properly connected Table 4 1 RC702 RC702 GE front panel introduction 4 2 Rear Panel Introduction Ground Hole AC PS Socket 2 AC PS Socket 1 Page 12 of 20 Hole DC PS Socket 2 DE PS Socket 1 Figure 4 5 RC70
Download Pdf Manuals
Related Search