4970/5100/4973/5103 Manual
Contents
1. Tel 973 598 9400 Fax 973 598 9410 Toll Free 800 457 4950 Artisan Controls Corporation 111 Canfield Ave Bldg B15 18 Randolph New Jersey 07869 USA ARTIRAN Solid State Timers and Controllers Section 6 Alarming Configuration The 4970 and 5100 controllers provide the ability to create alarms in order to inform the operator the timing cycle is about to end The Alarm Notification AL and the Alarm Duration Ad options are used to configure the alarming parameters along with the Time Value The first step in configuring the alarming is to set the Alarm Notification option to a value other than ALO0 default This must be done firstin order to be able to change the Alarm Duration and Time Value 1 options Option AL01 uses the triple beep pattern of the beeper AL02 turns the beeper on continuously ALO3 again uses the triple beep pattern but adds LED display flashing and finally option ALO4 enables continuous beeper operation with LED display flashing Once the alarm pattern is set the next item to be set is for now long the controller alarms Press Start Stop to display the Ad value and use the Up and Down arrows to change the last two digits to the length of time in seconds you require the notification pattern to last For example setting this option to Ad10 will turn the alarming on for 10 seconds The final option to configure is when the alarming starts Press Start Stop again to access this time value The contr2. The internal alarm beeps 3 times per second for 5 seconds at the end of the timing cycle The output relay is on during the timing cycle The LED display is on continuously The controller will resume the timing cycle if power is interrupted during a timing cycle The controller does not alarm before the end of the timing cycle If setting the timing range is all that is required you can skip to Section 3 for details about the operation of the controller The firmware version of the controller can be displayed by pressing and holding both the up and down arrows then applying powering to the controller 2014 Artisan Controls Version 1 80 V I SIT OUR WEB SITE AT www artisancontrols com Corporation Notice Artisan Controls Corporation assumes no responsibility for customers applications or product design it is the customers responsibility to analyze their application and test the selected product to determine its suitability for use The information and data contained herein is the sole and exclusive property of Artisan Controls Corporation Any duplication misuse or conversion of this information without the express written consent of Artisan Controls Corporation is illegal and will result in damages including court costs and attorney fees being assessed against the party misusing this property Tel 973 598 9400 Fax 973 598 9410 Toll Free 800 457 4950 Artisan Controls Corporation 111 Canfield A
3. AdXX Alarm length in seconds 01 99 Alarm Time Not used default XXXX Alarm time for ALO1 through AL04 Notes 2014 Artisan Controls Corporation O Sl Solid State Timers and Controllers Section 8 Controller Operation Once the controller has been configured apply power with no buttons pressed to operate the controller normally The controller is now in idle mode ready for adjustment of the time if configured as such and running of timing cycles The first step is to set the cycle time Setting the Cycle Time The Up and Down arrows are used to set the time for the interval cycle Pressing either the Up or Down button once will change the time up or down by a single digit Pressing and holding these buttons will start continually changing the time the longer the button is held the faster the time will change If the time value is increased past the upper limit it will wrap around to the lower limit and continue increasing The same holds true for decreasing the time below the lower limit it will wrap around and start decreasing from the upper limit NOTE 5100 amp 5103 Only To save the current time as one of the preset times press and hold the A B or C button for two seconds until the controller chirps twice Running a Timing Cycle To run atiming cycle simply press and release the Start Stop button or remote switch for 4973 5103 The output contacts switch and the time sta
4. Solid State Timers and Controllers Lens s TIMING ENDED ARTISAN START _ STOP START STOP 4970 amp 5100 Configurable Controllers User s Manual including 4973 amp 5103 The 4970 and 5100 configurable controllers provide a level of flexibility previously unavailable with products in it s class These devices allows the OEM to configure the products to suit numerous applications by providing the ability to configure many operating parameters including time range user s adjustability within the time range style of beeping and LED display activity at the end of the timing cycle power conservation recovery from power loss during timing and alarming before the end of the timing cycle all in one controller The 4973 and 5103 models provide an input for a remote switch used to start pause stop the timing cycle all other configurations are identical 2014 Artisan Controls Version 1 80 V I SIT OUR WEB SITE AT www artisancontrols com Corporation Notice Artisan Controls Corporation assumes no responsibility for customers applications or product design it is the customers responsibility to analyze their application and test the selected product to determine its suitability for use The information and data contained herein is the sole and exclusive property of Artisan Controls Corporation Any duplication misuse or conversion of this information without the express written consent of Artisan Controls Corporati
5. Pressing the Start Stop button again will energize the output contacts and continue the timing cycle Pressing and holding the Start Stop button for at least 2 seconds will reset the display back to the beginning of a new timing cycle and put the controller into idle mode Pressing the Up or Down buttons while paused will adjust the current time up or down and set this time as the default cycle time NOTE The remote switch is used instead of the Start Stop switch on the 4973 amp 5103 models Alarming During a Timing Cycle If alarming has been enabled once the alarm sounds the operator can press either the Up or Down buttons to silence the alarm the controller continues counting down in the timing cycle Pressing the Start Stop button both silences the alarm and puts the controller into pause mode P 2014 Artisan Controls Version 1 80 VISIT OUR WEB SITE AT www artisancontrols com Corporation Notice Artisan Controls Corporation assumes no responsibility for customers applications or product design it is the customers responsibility to analyze their application and test the selected product to determine its suitability for use The information and data contained herein is the sole and exclusive property of Artisan Controls Corporation Any duplication misuse or conversion of this information without the express written consent of Artisan Controls Corporation is illegal and will result in damages including court costs and attorney fees
6. data contained herein is the sole and exclusive property of Artisan Controls Corporation Any duplication misuse or conversion of this information without the express written consent of Artisan Controls Corporation is illegal and will result in damages including court costs and attorney fees being assessed against the party misusing this property Tel 973 598 9400 Fax 973 598 9410 Toll Free 800 457 4950 Artisan Controls Corporation 111 Canfield Ave Bldg B15 18 Randolph New Jersey 07869 USA Solid State Timers and Controllers Section 5 Operation Configuration cont Recovery From Power Interruption When power is lost during a timing cycle proper operation of the controller upon restoration of power can be critical to many applications This factory default for this option is Pr0O which enables the controller to immediately return to the point in the timing cycle when power was lost The time on the display when the power was lost is restored and the output relay is energized allowing the controller to complete it s timing cycle The next option is to have the controller restore the last known time as per the above option but to be placed into the pause mode with the relay off thereby requiring the operator to press Start Stop to continue the interrupted timing cycle Set this option to Pr01 in order select this power recovery mode The final option is code Pr02 which forces the controller to reset to the beginning of a
7. end of the timing cycle for one second regardless of the setting of the CE and EL values Finally option Ot03 keeps the relay off always generally used to conserve power LED Display Power This option changes the operation of the LED display when the controller is left idle Setting this to LPOO leaves the display energized continuously as long as the controller has power applied default If this option is changed to LP0O1 the controller dims the display after 1 minute of no button activity when in the idle state The display will stay at full brightness when either actively running a timing cycle or when paused during a timing cycle It is only when the timing cycle is fully complete does the 1 minute countdown start Once the display dims pressing any button restores the display to full brightness and resets the 1 minute countdown Setting this option to LP02 will cause the display to turn off completely instead of dimming after the 1 minute countdown This can provide significant power savings when the unit is power by 12V DC thereby extend the life of battery and solar powered systems 2014 Artisan Controls Version 1 80 VISIT OUR WEB SITE AT www artisancontrols com Corporation Notice Artisan Controls Corporation assumes no responsibility for customers applications or product design it is the customers responsibility to analyze their application and test the selected product to determine its suitability for use The information and
8. use The information and data contained herein is the sole and exclusive property of Artisan Controls Corporation Any duplication misuse or conversion of this information without the express written consent of Artisan Controls Corporation is illegal and will result in damages including court costs and attorney fees being assessed against the party misusing this property Tel 973 598 9400 Fax 973 598 9410 Toll Free 800 457 4950 Artisan Controls Corporation 111 Canfield Ave Bldg B15 18 Randolph New Jersey 07869 USA Solid State Timers and Controllers Section 3 Timing Configuration Timing Cycle Range Options This is the primary option to be configured for any application Use the Start Stop button to display the rA option code Use the Up and Down buttons to set the timing range to rA00 for minutes and seconds up to 99 59 default rA01 for hours and minutes up to 99 59 rA02 for seconds up to 9999 rA03 for seconds up to 99 99 rA04 for minutes up to 9999 or rA05 for hours up to 9999 Cycle Time Adjustment If you need your users to have the ability to set any time within the full timing range you configured above leave this value at CA00 default With this value configured the following time values will display as indicating that they are not available for this configuration If your application requires limiting the users time range use the Up or Down button to set this option to CA01 the press Start Stop t
9. 2014 Artisan Controls Version 1 80 VISIT OUR WEB SITE AT www artisancontrols com Corporation Notice Artisan Controls Corporation assumes no responsibility for customers applications or product design it is the customers responsibility to analyze their application and test the selected product to determine its suitability for use The information and data contained herein is the sole and exclusive property of Artisan Controls Corporation Any duplication misuse or conversion of this information without the express written consent of Artisan Controls Corporation is illegal and will result in damages including court costs and attorney fees being assessed against the party misusing this property Tel 973 598 9400 Fax 973 598 9410 Toll Free 800 457 4950 Artisan Controls Corporation 111 Canfield Ave Bldg B15 18 Randolph New Jersey 07869 USA Controller Configuration Timing Cycle Range VY Value rA00 Minutes Seconds 00 01 to 99 59 rA01 Hours Minutes 00 01 to 99 59 rA02 Seconds 1 to 9999 default rA03 Seconds 0 01 to 99 99 rA04 Minutes 1 to 9999 rA05 Hours 1 to 9999 Cycle Time Adjustment CAOO Full time range available default CA01 Adjustable from Time Value 2 to Time Value 3 CA02 Timing fixed at Time Value 2 Timing Increment tIXX Timing change increment tl01 default Lower Limit or Fixed Time Not used default XXXX Lower Time Limit for CA01 or Fixed
10. Q D WIRING FOR 4970 amp 5100 Operating Voltage no polarity for DC All terminals are 0 25 Q D REMOTE START SWITCH WIRING FOR 4973 amp 5103 Output Relay Contacts NC Operating Voltage no polarity for DC 2014 Artisan Controls Version 1 80 VISIT OUR WEB SITE AT www artisancontrols com Corporation Notice Artisan Controls Corporation assumes no responsibility for customers applications or product design it is the customers responsibility to analyze their application and test the selected product to determine its suitability for use The information and data contained herein is the sole and exclusive property of Artisan Controls Corporation Any duplication misuse or conversion of this information without the express written consent of Artisan Controls Corporation is illegal and will result in damages including court costs and attorney fees being assessed against the party misusing this property Tel 973 598 9400 Fax 973 598 9410 Toll Free 800 457 4950 Artisan Controls Corporation 111 Canfield Ave Bldg B15 18 Randolph New Jersey 07869 USA
11. Time for CA02 Upper Limit Not used default XXXX Upper Time Limit for CA01 Cycle End Notification CE00 Triple beep for End Length default CE01 Triple beep until key pressed CE02 Continuous tone for End Length CE03 Continuous tone until key pressed CE04 Triple beep for End Length LED display flashing CE05 Triple beep until key pressed LED display flashing CE06 Continuous tone for End Length LED display flashing CE07 Continuous tone until key pressed LED display flashing End Notification Length ELXX Notification cycle end in seconds EL05 default Output Relay Type otoo Relay on during timing cycle default Ot01 Relay on for Cycle End Notification length Ot02 Relay on for 1 second at end of timing cycle Oto3 Relay always OFF LED Display Power LPOO LED display always on default LP01 Display dims after 1 minute in idle mode LP02 Display OFF after 1 minute in idle mode Recovery from Power Interruption Proo Return to last time output on continue timing default Pr01 Return to last time output off in pause mode Pr02 Return to full cycle time ready for new cycle Alarming Notification ALOO Alarming disabled default ALO1 Triple beeping AL02 Continuous tone AL03 Triple beeping with LED display flashing AL04 Continuous tone with LED display flashing Alarm Duration Ad00 Alarming disabled default
12. being assessed against the party misusing this property Tel 973 598 9400 Fax 973 598 9410 Toll Free 800 457 4950 Artisan Controls Corporation 111 Canfield Ave Bldg B15 18 Randolph New Jersey 07869 USA O i Solid State Timers and Controllers Section 9 Installation TIMING ENDED wnwixew spunod youl 0 4921q Buunow u zyl L A 093R Max 2 63 Square Minimum Panel Cutout Required 2014 Artisan Controls Version 1 80 VISIT OUR WEB SITE AT www artisancontrols com Corporation Notice Artisan Controls Corporation assumes no responsibility for customers applications or product design it is the customers responsibility to analyze their application and test the selected product to determine its suitability for use The information and data contained herein is the sole and exclusive property of Artisan Controls Corporation Any duplication misuse or conversion of this information without the express written consent of Artisan Controls Corporation is illegal and will result in damages including court costs and attorney fees being assessed against the party misusing this property Tel 973 598 9400 Fax 973 598 9410 Toll Free 800 457 4950 Artisan Controls Corporation 111 Canfield Ave Bldg B15 18 Randolph New Jersey 07869 USA O Sl Solid State Timers and Controllers Section 10 Wiring All terminals are 0 25
13. e end of the timing cycle The beeper can be configured to either emit triple beeps once per second default or to turn on continuously The LED display can be set to stay fully lit default or to Length Display flash twice per second Key Triple Cont Cont Flash See the table to the right for details on configuring this option Press the Up and Down buttons to change this option to the desired value If the pattern selected uses the End Length press Start Stop again to access the EL code then use the Up and Down arrows to configure the number of seconds the end notification is to last up to 99 seconds setting this value to 00 turns the Cycle End Notification off EL End Length configured for EL code Section 5 Operation Configuration Output Relay Type The output relay of the 4970 can be configured to operate in several different modes The default mode Ot00 is for the relay to be energized during the timing cycle for standard countdown timer operation The next two options allow the relay to be off during timing and to energize at the end of the cycle this is typically used to trigger other means of indicating that the timing cycle is ended Option Ot01 turns the relay on for the duration of the Cycle End Notification Depending on the CE and EL configurations this can be either the time defined in the EL parameter or until the operator presses a key Option Ot02 turns the relay on at the
14. est and configuration reset The controller displays until the Up button is released after which it displays UP Press the Up button and it displays dn now press the Down button The unit then displays SS press the Start Stop button After this button test the controller display scrolls through the digits 0 through 9 illuminating the LED above the display every other value The output relay is closed for 2 second then the configuration memory is tested and reset back to the default values above Finally the controller resets and displays 0 05 This feature can also be used as a basic controller test DEFAULT FACTORY CONFIGURATION Description Timing in minutes seconds Time adjustable over full range Time increments by 1 No time limiting or fixed timing No time limiting Triple beeps for EL secs end of cycle Length of annunciation 5 sec Output relay on during timing LED display on continuously Continues timing cycle if power interrupted Alarming disabled Alarming disabled Alarming disabled Configuration check code 2014 Artisan Controls Version 1 80 VISIT OUR WEB SITE AT www artisancontrols com Corporation Notice Artisan Controls Corporation assumes no responsibility for customers applications or product design it is the customers responsibility to analyze their application and test the selected product to determine its suitability for
15. new timing cycle when power returns needing Start Stop to be pressed for a new timing cycle This would be used for applications which requires full timing cycles with no interruptions for proper operation Output Type Ot 00 Output relay on during timing Ot 01 Relay on for end notification length Ot 02 Relay on for 1 second end Ot 03 Relay always off LED Display Power LP 00 LED display always on LP 01 Display dims after 1 minute in idle mode LP 02 Display OFF after 1 minute in idle mode Recovery from Power Interruption Pr 00 Return to last time output on continue timing Pr 01 Return to last time output off in pause mode Pr 02 Return to full cycle time ready for new cycle 2014 Artisan Controls Version 1 80 VISIT OUR WEB SITE AT www artisancontrols com Corporation Notice Artisan Controls Corporation assumes no responsibility for customers applications or product design it is the customers responsibility to analyze their application and test the selected product to determine its suitability for use The information and data contained herein is the sole and exclusive property of Artisan Controls Corporation Any duplication misuse or conversion of this information without the express written consent of Artisan Controls Corporation is illegal and will result in damages including court costs and attorney fees being assessed against the party misusing this property
16. o access the first time value Use the Up and Down buttons to set this to the minimum time then press Start Stop again and use the Up and Down buttons to set the next value to the maximum time Note Be sure to set the first time less than second time Finally you can prevent any time adjustments by the operator by setting this option to CA02 With this option the first time is set for the fixed cycle time value the second time value will display as indicating that it is not used Timing Increment This value is the amount that the time displayed changes when using the Up and Down arrows The default value is tl01 and can be set to any value up to 199 Setting the value to tl15 will cause the time to change in 15 second increments The controller will always round off the current value to increments of this value for example if the lower limit is set to 1 10 by using the CA codes and the time increment is 15 the will not allow times lower than 1 15 to be set Timing Cycle Range Time Adjustment Increment rA 00 Minutes Seconds 00 01 to 99 59 Time increment value default 1 rA 01 Hours Minutes 00 01 to 99 59 ar 3 z rA 02 Seconds 1 to 9999 rA 03 Seconds 0 01 to 99 99 OE i ODO ocean eee rA 04 Minutes 1 to 9999 XXXX Displays Lower Time Limit for CA 01 rA 05 Hours 1 to 9999 XXXX Displays Fixed Time for CA 02 arate Cycle Time Adjustment Upper Limit Time Disabled by code CA 00 or CA 02 XXXX Displays Upper Time Limit fo
17. oller now displays the value which indicates at what time before the end of the cycle the alarming should start This value is based on the timing range selected For example setting this value to 1 00 when in range 01 mm ss indicates that the alarming starts one minute before the end of the cycle but if you are in timing range 02 hh mm you would have to set it to 0 01 to start the alarming pattern at 1 minute Alarming Notification AL 00 No alarming enabled AL 01 Triple beeping AL 02 Continuous tone AL 03 Triple beeping with display flash AL 04 Continuous tone with display flash Alarm Duration Ad 00 Disabled by code AL 00 Ad XX Alarm length in seconds 01 99 Alarm Time Disabled by code AL 00 XXXX Displays alarm time for AL 01 AL 04 P P 2014 Artisan Controls Version 1 80 VISIT OUR WEB SITE AT www artisancontrols com Corporation Notice Artisan Controls Corporation assumes no responsibility for customers applications or product design it is the customers responsibility to analyze their application and test the selected product to determine its suitability for use The information and data contained herein is the sole and exclusive property of Artisan Controls Corporation Any duplication misuse or conversion of this information without the express written consent of Artisan Controls Corporation is illegal and will result in damages including court costs and atto
18. on is illegal and will result in damages including court costs and attorney fees being assessed against the party misusing this property Tel 973 598 9400 Fax 973 598 9410 Toll Free 800 457 4950 Artisan Controls Corporation 111 Canfield Ave Bldg B15 18 Randolph New Jersey 07869 USA O i Solid State Timers and Controllers Table of Contents Section 1 Basic Configuration Select the time range backwards compatable with previous versions Section 2 Advanced Configuration Instructions for setting the other options in the controller Section 3 Timing Configuration Setting the time range used and the adjustability within the range Section 4 Notification Configuration Set how the controller announces the end of the timing cycle Section 5 Operation Configuration Set the functioning of the output relay recovery from power interruption and LED display power saving options Section 6 Alarming Configuration Alarm before the end of the timing cycle Section 7 Configuration Example amp Form Worksheet for documenting your configuration Section 8 Controller Operation Using the controller after configuration Section 9 Installation Section 10 Wiring 2014 Artisan Controls Version 1 80 VISIT OUR WEB SITE AT www artisancontrols com Corporation Notice Artisan Controls Corporation assumes no responsibility for customers applications or product design it is the customers respon
19. r CA 01 CA 00 Full time range available CA 01 Adjustable between limits CA 02 Timing fixed 2014 Artisan Controls Version 1 80 VISIT OUR WEB SITE AT www artisancontrols com Corporation Notice Artisan Controls Corporation assumes no responsibility for customers applications or product design it is the customers responsibility to analyze their application and test the selected product to determine its suitability for use The information and data contained herein is the sole and exclusive property of Artisan Controls Corporation Any duplication misuse or conversion of this information without the express written consent of Artisan Controls Corporation is illegal and will result in damages including court costs and attorney fees being assessed against the party misusing this property Tel 973 598 9400 Fax 973 598 9410 Toll Free 800 457 4950 Artisan Controls Corporation 111 Canfield Ave Bldg B15 18 Randolph New Jersey 07869 USA O i Solid State Timers and Controllers Section 4 Notification Configuration Cycle End Notification and End Length This option configures the length and type of the audible and visual indication thst the timing cycle is complete The selected pattern can be set to end automatically after the configured End Length default or to continue until the operator presses any of the three keys thereby acknowledging th
20. rney fees being assessed against the party misusing this property Tel 973 598 9400 Fax 973 598 9410 Toll Free 800 457 4950 Artisan Controls Corporation 111 Canfield Ave Bldg B15 18 Randolph New Jersey 07869 USA O i Solid State Timers and Controllers Section 7 Configuration Example and Form Configuration Example The desired operation for this example is 1 the timing range is minutes and seconds mm ss 2 cycle times to be adjustable from 15 to 25 minutes in 15 second increments 3 continuous tone with LED display flashing at the end of the cycle until the operator to presses a key 4 the output relay turns on until the operator presses a key 5 the LED will dim after 1 minute of inactivity 6 interrupted timing cycles must be manually continued for safety 7 alarming is enabled triple beeps for 10 seconds and finally 8 the alarming starts 30 seconds before the end of the timing cycle These are the configuration options to be set to meet these requirements Code Description Timing in minutes seconds Time adjustable between limits Time adjustable in 15 second increments Minimum adjustable time value Maximum adjustable time value Continous tone with LED flash until key press LED displays goes dim after 1 minute Recovers to interrupted cycle time in pause mode Triple beep alarming Alarming for 10 seconds maximum Alarming starts 30 seconds before end
21. rts counting down on the LED display The LED above the display will start alternating on and off and the colon will also alternate on the time display if you are in the minutes seconds or hours minutes time ranges the colon is not used when in either of the seconds ranges Once the display counts down to 0 the output contacts switch back to the off position the LED above the time display turns on continuously and the beeper and or LED display will start the end of cycle alarming pattern selected If the length of the end of cycle notification was configured to use the EL value after that configured time all of the beeper amp display activity will stop and the display will change from 0 back to the initial cycle time and the LED turns off the controller is back in idle mode Pressing any buton during this time will also stop the notification and return to the preset cycle time If the length of the end of cycle notification was set to wait for a key press the beeper and display activity will continue until any of the buttons are pressed at that time the display agains returns to the initial cycle time and the beeper and LED above the display turns off Pausing a Timing Cycle When the controller is running a cycle pressing the Up or Down buttons will have no affect on its operation Pressing the Start Stop button will imdediately stop the time display at the current value and turn the output contacts off The controller is now in the pause mode
22. sibility to analyze their application and test the selected product to determine its suitability for use The information and data contained herein is the sole and exclusive property of Artisan Controls Corporation Any duplication misuse or conversion of this information without the express written consent of Artisan Controls Corporation is illegal and will result in damages including court costs and attorney fees being assessed against the party misusing this property Tel 973 598 9400 Fax 973 598 9410 Toll Free 800 457 4950 Artisan Controls Corporation 111 Canfield Ave Bldg B15 18 Randolph New Jersey 07869 USA ARTIN Solid State Timers and Controllers Section 1 Basic Configuration The basic configuration for these controllers is to select the time range this maintains backwards compatability with previous versions of these controllers To access the basic controller configuration hold the Down button apply power and release the button The controller displays a single digit indicating the time range Code Timing Range 0 Seconds 0 01 to 99 99 Minutes Seconds 00 01 to 99 59 Seconds 1 to 9999 Hours Minutes 00 01 to 99 59 Use the up and down buttons to change to the desired range then turn the controller off The other default operating parameters shown below can be modified using the Advanced Configuration option in the next section Timing is adjustable over the whole timing range
23. ve Bldg B15 18 Randolph New Jersey 07869 USA O i Solid State Timers and Controllers Section 2 Advanced Configuration To access the advanced controller configuration press and hold the Start Stop button apply power and release the button The unit then displays the first configuration item which is the timing range showing rA on the left side of the display Pressing and releaseing the Start Stop button again move to the next configuration item which is the cycle adjustment type full partial single value indicated by the CA on the display Use the Start Stop button to cycle through all the configuration items and use the Up and Down arrow buttons to change the value of each configuration item as required The last item on the listis a configuration check code which is calculated based on all the values of the configuration items and can be used to verify the proper setting of the controller configuration The three time values are shown as which indicates that they are not used the options which enable their use are disabled The time values are adjusted just like the time setting in normal operation the Up and Down buttons change the value holding them down scrolls the value All time values will wrap around at either end of their range and are in the units selected for the time range To reset the controller to its default values as shown below press and hold the Up button while applying power to access the self t
Download Pdf Manuals
Related Search