Single Unit Rapid Charger
Contents
1. DC power supply from the ENDURA NCC0325 3 Turn the locking screw on the bottom of the charging pod counter clock wise several rotations The screw remains connected to the charging pod Lift the charging pod from the charging base 4 Insert the replacement charging pod into the charging base and secure with the locking screw Do not over tighten the screw 5 Inspect the charging contacts to ensure they are clean and unobstructed 6 Connect the AC to DC power supply to the ENDURA NCC0325 You are now ready to charge a battery compatible with the charging pod Charging A Battery 1 Confirm that the charging pod and battery are compatible 2 Connect the DC end of the power supply to the DC plug on the back of the charger then connect the AC adaptor to a wall outlet 120V AC 3 Place battery to be charged in the charging pod The battery may be charged while attached to the radio Note If the battery is attached to radio turn the radio off while in the charger 4 When a battery is placed in the charging pod the charge status LED will illuminate ORANGE for a short period while the charger performs a battery diagnostic Once completed the charge status LED will change to RED This indicates the battery is charging 5 While a battery is charging the charge status LED will illuminate RED with no flashing If the charge status LED is red and flashes a fault has been detected The flash pattern represents a specific fault2. ENDURA Single Unit Rapid Charger FOR RECHARGEABLE LMR BATTERIES h Model NCCO325 Introduction Thank you for purchasing an ENDURA NCC0325 Single Unit Rapid Charger This high quality product is designed for use with rechargeable LMR batteries With the appropriate charging pod installed it can charge batteries with Lithium ion Li lon nickel metal hydride NiMH or nickel cadmium NiCd chemistry Important 1 Read all Caution statements below and this User Manual before attempt ing to charge a battery 2 Check to make sure a charging pod compatible with your battery is prop erly installed on charger before placing battery in pod 3 Position charger away from TVs radios or other receivers to prevent the charger from interfering with these types of products 4 Always charge new batteries completely before initial use Recycle bat teries when they can no longer be used Do not discard unwanted batter ies in the trash or incinerate Batteries exposed to fire or excessive heat may explode 5 For best battery performance charge NiCd and NiMH batteries when they are fully discharged Caution 1 Never charge alkaline or dry cell batteries with this charger They may burst and cause damage or personal injury 2 Do not charge Li lon NiMH or NiCd batteries unless they are designed with overcharge protection 3 Use charger indoors only Do not expose the charger to rain any liquids or exc
3. charger supplier with radio then resume use of ENDURA NCC0325 Indicates over heat condition for a Li lon battery Battery temperature is over 43 C and charging has stopped Battery protection circuit may be defective Indicates battery contact is open and current is not pass ing through the and contacts on the battery Check charging pod to confirm compatibility with battery Indicates charging complete but battery is under charged Battery voltage is below minimum level required Warranty And Service During Warranty The ENDURA NCC0325 is made from high quality materials and designed to provide years of reliable service The following warranty applies Power Products Unlimited Inc PPU warrants this product to be free from defects in workmanship and materials for one year from date of purchase by the end user This warranty applies to the original purchaser and is void if the product has been altered misused damaged neglected purchased outside the United States or if repair is required because of normal wear and tear This is the only warranty made by PPU In no event will PPU its af filiates subsidiaries related entities or their respective directors officers or employees be liable for any damages beyond repair or replacement as described above including without limitation indirect incidental or con sequential damages For service under warranty return the product along with dated proof of p
4. condition See section Fault Conditionsfor details 6 When the battery is charged to 80 of capacity the charge status LED will change to GREEN and begin to flash It is recommended that the battery be charged to at least 80 capacity before use 7 The charge status LED will illuminate GREEN with no flashing when the battery is fully charged Note Remove battery from charger within 15 hours after charging is complete 8 After removing a fully charged battery the charge status LED may remain illuminated for a few seconds Allow the charge status LED to go off before placing another battery in the charging pod 9 The ENDURA NCCO325 is designed to operate at room temperatures be tween 15 C and 30 C Charging batteries at room temperatures outside this range may result in under charging of batteries Fault Conditions When the charge status LED flashes RED a fault condition exists There five different flash patterns each indicating a specific type of fault The flash patterns and fault conditions are as follows LED Flash Pattern Flashes 1 Time Flashes 2 Times Flashes 3 Times Flashes 4 Times Flashes 5 Times Fault Type Indicates over current condition caused by battery short circuit Check battery contacts Do not attempt charging the battery if short circuit exists Indicates battery diagnostic has timed out and cannot be completed due to excessively low battery voltage Charge battery with
5. essive moisture 4 Do not attempt to charge a battery without first installing the appropriate charging pod Use only charging pods designed for the ENDURA NCC0325 charger Disconnect charger from power supply before installing adjust ing or removing the charging pod 5 Make sure contacts in charging pod and battery are clean Do not allow wire or metal objects to touch contacts in charging pod or any internal part of the charger 6 Do not remove the charger s housing or make any modification to the charger 7 Use only the power supply provided with the ENDURA NCC0325 charger If a replacement power supply is required order part number NCC0325 Use of other power supplies may damage the charger or batteries you may be attempting to charge ENDURA NCCO325 Features 1 Power Supply 2 Endura NCCO325 Single Unit Rapid Charger 3 Removable Charging Pod Note Quick reference informa tion for charge status is 4 Charge Status LED located on pon of charger Replacing A Charging Pod The charging pod is made from quality materials and designed to provide years of service when properly used In most cases the charging pod will only be replaced when you want to use the charger with a different battery Follow these steps to change the charging pod 1 Obtain a charging pod made specifically for the ENDURA NCCO325 Confirm that the charging pod is compatible with the battery you want to charge 2 Unplug the AC to
6. urchase to the retailer where purchased or to Power Products If returning directly to Power Products follow these instructions 1 Send to Power Products Warranty Service Department 2170 Brandon Trail Alpharetta GA 30004 For your protection we recommend you ob tain proof of delivery for your shipment 2 Include with your product dated proof of purchase your name and day time teleohone number and return address street address only return shipments cannot be made to a PO Box 3 All items sent become the property of Power Products and will not be returned ENDURA NCC0325 Specifications Dimensions 115 x 136 x 66 mm 4 5 x 5 4 x 2 6 inches Weight Charger Only 275g 6lbs Compatible Chemistries NiCd NiMH Li Ion Operating Temperature 15 C 30 C Storage Temperature 0 C 65 C Power Supply Type AC to DC Power Supply Output 15V 18V DC 500mA 900mA Specifications subject to change without notice l 200 Commercial St Nevada City CA 95959 Toll Free 800 552 0707 Office 530 477 2590 Fax 530 478 9188 www 49ercommunications com
Download Pdf Manuals
Related Search