USER`S MANUAL - Pdfstream.manualsonline.com
Contents
1. 7 SYMPTOM THE WATER IS NOT BEING CLEANED BY THE FILTER a Check to see if the filter is in place Clean the filter if it is dirty b Check the chemical balance of the water If the pH is incorrect the sanitizing agents will not function properly SYMPTOM THE WATER PULSATES OR THERE IS MINIMUM WATER FLOW a Adjust the water level This usually occurs only when the water level is low Add water until the filter and jets are covered b This problem is caused by excess air in the pump circulation system Check to see if the primer cap is fully tightened Prime the pump again and fully tighten the primer cap see PRIMING THE SPA JET UNIT on page 10 SYMPTOM THE SPA JET UNIT CAVITATES DURING USE a Adjust the water level This usually occurs only when the water level is low Add water until the filter and jets are covered b This problem is caused by excess air in the pump circulation system Check to see if the primer cap is fully tightened Prime the pump again and fully tighten the primer cap see PRIMING THE SPA JET UNIT on page 10 10 SYMPTOM THE SPA JET UNIT CONTINUES TO RUN AFTER IT HAS BEEN SHUT OFF 11 12 a When you press the on off button once the spa jet unit will run at low speed heating the water Press the button again and the spa jet unit will run at high speed filtering the water Press the button a third time and the spa jet unit will shut off The spa jet unit also features an a2. 1 4 Nut Heat Control Nut 5 16 Rubber Washer 5 16 Washer On Off Switch Bracket Key No Qty Banat a N saa NPBA AANA HAAN N AAG AAA AAA RO399A Description Rubber Damper Wire Harness Air Control Knob On Off Switch Assembly Thermostat Knob Primer Cap 8 x 1 2 Screw Console Overlay On Off Wire Harness 10 x 1 Screw 10 Nut Motor Mount Bracket Right Side Support Wire Ties Filter Cover 3 8 Compression Fittings Temperature Tube Trim Primer O ring Upper Heater Gasket 8 x 3 4 Screw 10 Washer Left Side Support Pressure Switch Heater Ground Wire Air Pump Key Warning Decal User s Manual Water Treatment Kit Water Test Strips Video Note indicates a non illustrated part Specifications are subject to change without notice
3. Ball and insert the ball plug through the mesh into the Support Ball The head of the ball plug will hold the Support Ball in place Note The Support Ball 4 is not a toy 7 T S Place the Spa Cover 11 over the Side Panels 1 2 and the Spa Jet Unit 13 Be sure that the Spa Cover is properly centered and that the straps on the Spa Cover line up with the straps extend ing from the slots in the Side Panels 1 2 Snap each of the six latches on the Spa Cover 11 into the buckles on the straps extending from the slots in the Side Panels 1 2 Latches and Buckles USING THE HYDROTHERAPY SPA The hydrotherapy spa is designed for up to four adults The six water jets can be regulated to provide a relaxing massage to sooth away stress and the strength of the water massage can be adjusted by the air control The hydrotherapy spa holds 300 gallons of water and offers an automatic programmable heating 70 F to 104 F and filtration system The guidelines below explain how to properly use the hydrotherapy spa Follow these guidelines to maintain the spa for your long term enjoyment PRIMING THE SPA JET UNIT The water pump in the spa jet unit must be primed before you use the hydrotherapy spa the first time You must also prime the pump before using the unit each time you re fill the hydrotherapy spa To prime the spa jet unit remove the primer cap from the console Fill the spa jet unit with at le
4. Liner with the hole in the Fabric Spa Surround and the Inflation Side Panel 2 Flip the flap on the Fabric Spa Surround 8 over the low section of the Inflatable Spa Liner 9 be visible in this hole 4 Remove the power cord from the Spa Jet Unit 13 With the help of a second person place the Spa Jet Unit 13 over the Side Panel 1 and the section of the Inflatable Spa Liner 9 which does not have the cushion Be extremely careful not to tear the Inflatable Spa Liner 9 as you slide the Spa Jet Unit into place 5 Before you fill the hydrotherapy spa be sure that it is in the position you want and that it can be easily serviced if needed Once the hydrotherapy spa is filled with water it will need to be drained to be moved Using a garden hose or other clean water source begin filling the hydrotherapy spa until the jet and filter openings on the Spa Jet Unit 13 are covered with water Do not fill the RENEW 800 more than 20 deep with water After the RENEW 800 is full you must prime the Spa Jet Unit 13 before using the hydrotherapy spa see PRIMING THE SPA JET UNIT on page 10 6 Insert the Support Ball 4 into the mesh pocket on the underside of the Spa Cover 11 See inset drawing A Insert the inflation tube into the hole in the Support Ball 4 Inflate the Support Ball See inset drawing B When the Support Ball 4 is inflated remove the inflation tube from the Support
5. con cerning the use of outdoor spas The location must be close to an electrical outlet Do not use an extension cord with the hydrotherapy spa The hydrotherapy spa should be close to a source of water We recommend that you place the hydrotherapy spa on a water and stain resistant non slip sur face Be sure that the location you choose is stable It must be able to support the weight of the hydrotherapy spa when it is filled with water plus the weight of the occupants The hydrotherapy spa weighs approximately 2400 pounds when filled with water Think about environmental factors such as rain wind shade sunlight and so forth You should be able to monitor the use of the hydrotherapy spa from your home to prevent unauthorized use by children Be sure that there is room around the hydrothera py spa to permit servicing of the unit The diame ter of the tub is 69 You should allow for this size plus the size of the spa jet unit when choosing the location Be sure to note any other considerations such as aesthetics or privacy concerns which may affect the safety or enjoyment of using the hydrotherapy spa ASSEMBLY Before beginning assembly carefully read the e Assembly requires the included air pump following information and instructions e Read each assembly step before you begin e Place all parts in a cleared area and remove the packing materials do not dispose of t
6. console control is explained below Primer This opening allows you to prime the spa jet unit before operation see PRIMING THE SPA JET UNIT on page 10 Air Control Determines the amount of air that is in the spa jet system during operation If the control is turned to the left the amount of air flowing through the jets will increase If the control is turned to the right the amount will decrease Thermostat Controls the temperature of the water The water heats at about 1 7 F an hour with the cover on The thermostat can be set to heat the water from SPA JET UNIT OPERATION The spa jet unit features three hydro therapy jets a whirlpool jet a suction vent and a filter housing The three hydro therapy jets A located on the front of the spa jet unit focus the water massage on your neck and back THERMOSTAT 70 F to 104 F Use a medical or other accurate ther mometer to check the temperature of the water On Off Turns the spa jet unit on and off When you first press the on off button the spa jet unit will run at low speed providing gentle hydrotherapy Press the button again and the jet unit will run at high speed providing more intense hydrotherapy Press the button a third time and the spa jet unit will shut off The spa jet unit also features an automatic mode which heats and filters the water when the spa is left unattended When the spa jet unit is first plugged in or if the buttons on th
7. minutes See the instructions with your test strips or pH test kit for addi tional information about testing and adjusting the pH SANITIZING THE HYDROTHERAPY SPA Please refer to your local pool and spa supplier for information concerning which chemicals you should use in your area to sanitize the spa The most common sanitizing agent is a solid bromine concentrate The amount required varies according to several factors such as user load temperature water conditions and so forth Proper water maintenance is a fairly complex process We recommend that you contact your local pool and spa supplier for information on how you should best accomplish this Most problems can be solved by following the simple steps below Find the symptom that applies and follow the steps listed If further assistance is needed call our Customer Service Department toll free at 1 800 999 3756 Monday through Friday 6 a m until 6 p m Mountain Time 1 SYMPTOM THE SPA WILL NOT OPERATE a Check the power cord The power cord must be plugged into a grounded outlet see PLUG GING IN THE HYDROTHERAPY SPA on page 10 b Check to see if the GFCI breaker is tripped or was not turned on Reset the GFCI breaker 2 SYMPTOM THE CIRCUIT BREAKER OR GFCI BREAKER TRIPS WHILE THE SPA IS OPERATING a Reset the circuit breaker If the circuit breaker trips again contact a qualified electrician for service 3 SYMPTOM THE PUMP HUMS a The filter ma
8. spa will increase the level of humidity in your home The location you choose should be well ventilated You may need to install a ventilation fan or use a dehumidifier The location must be close to an electrical outlet Do not use an extension cord with the hydrotherapy spa The hydrotherapy spa should be close to a source of water Do not use the hydrotherapy spa on carpet or other material that may be damaged by moisture We recommend that you place the hydrotherapy spa on a water and stain resistant non slip sur face with a floor drain for any water that may splash from the hydrotherapy spa Be sure that the location you choose is stable It must be able to support the weight of the hydrotherapy spa when it is filled with water plus the weight of the occupants The hydrotherapy spa weighs approximately 2400 pounds when filled with water Do not use the hydrotherapy spa above a finished living area due to the risk of water damage Be sure that there is room around the hydrothera py spa to permit servicing of the unit The diame ter of the tub is 69 You should allow for this size plus the size of the spa jet unit when choosing the location Be sure to note any other considerations such as aesthetics or privacy concerns that may affect the safety or enjoyment of using the hydrotherapy spa If you set up the hydrotherapy spa outside 1 You should check your local building codes
9. Model No IMHS80081 Serial No Write the serial number in the space above for reference Serial Number Decal QUESTIONS As a manufacturer we are com mitted to providing complete customer satisfaction If you have questions or find that there are missing or damaged parts we will guarantee complete satis faction through direct assistance from our factory TO AVOID UNNECESSARY DELAYS PLEASE CALL DIRECT TO OUR TOLL FREE CUSTOMER HOT LINE The trained techni cians on our customer hot line will provide immediate assis tance free of charge to you CUSTOMER HOT LINE 1 800 999 3756 Mon Fri 6 a m 6 p m MST CAUTION Read all precautions and instruc tions in this manual before using this equipment Save this manual for future reference USER S MANUAL TABLE OF CONTENTS EIMIT ED WARPING Y ara aaee cee acne tiated e a aa e a ceca ap altel a aa was asda tate E E aS a 2 IMPORTANT SAFETY INSTRUCTIONS 00000 eee 3 WARNING DECAL PLACEMENT 00 000 eee eae 5 BEFORE YOU BE GIN site tent Atte de Phila a a Ba Eh 8 O ON MN ed id tear oe ht 6 CHOOSING A LOCATION FOR THE HYDROTHERAPY SPA 00000 anaana naana 7 ASSEMBLY s Greya apiece erg dace ae tale th Ste Aa tap ie eee aie Sea oncaeid ee A eo ia aa eee Be 8 USING THE HYDROTHERAPY SPA 0 0 0 000 cee nae 10 MAINTENANCE oe fn oh oiek cen do pdt eet et ee Aine ee she nt A A ta eS Oe sce NS 13 TROUBLESHOOTING a 224 408 whan Ga d
10. W 800 The innovative RENEW 800 offers the features and quality of a traditional hot tub at an affordable price Best of all the RENEW 800 is fully portable so you can take it wherever there is an electrical outlet The RENEW 800 allows you to relax and unwind in the comfort of your own home For your benefit read this manual carefully before using the IMAGE RENEW 800 If you have addition al questions please call our Customer Service Spa Cover Locking Buckle Inflation Valve Department toll free at 1 800 999 3756 Monday through Friday 6 a m until 6 p m Mountain Time excluding holidays To help us assist you please note the product model number and serial number before calling The model number is IMHS80081 The serial number can be found on a decal attached to spa jet unit see the front cover of this manual Before reading further please familiarize yourself with the parts that are labeled in the drawing below Console Under Spa Cover Spa Jet Unit Power Cord Ground Fault Circuit Interrupter GFCI CHOOSING A LOCATION FOR THE HYDROTHERAPY SPA There are many factors to consider when choosing a location to set up the hydrotherapy spa These factors vary depending on whether you use the hydrotherapy spa inside or outside We have listed several factors you may wish to consider as you decide where you want to use the hydrotherapy spa If you set up the hydrotherapy spa inside 1 The hydrotherapy
11. a is intended for home use only Do not use the spa in any commer cial rental or institutional setting Use the hydrotherapy spa only on a level surface Do not use the spa on carpet or other materials that could be damaged by moisture Do not use the spa on rough or sharp surfaces such as gravel or wood chips The hydrotherapy spa will weigh approxi mately 2400 pounds when it is assembled and filled with water Be sure that the loca tion you select for the spa will support this weight plus the weight of the occupants Inspect and tighten all parts regularly Replace any worn parts immediately DANGER Risk of injury Do not remove or alter the covers on the suction fittings Never operate the hydrotherapy spa if the suction guard is missing or broken Keep hair and body away from the suction guard If you need to replace a suction fitting be sure that the flow rate of the replacement is compatible Do not bring any object into the hydrothera py spa that could puncture the liner Never insert any object into any opening Do not sit on the spa cover or place objects on it It is not designed to support weight Remove any water which may collect on the Spa cover Keep children and pets away from the hydrotherapy spa when it is not in use Keep all chemicals away from children and pets The pH and chemical balance of the water 15 16 17 18 19 20 21 must be maintained as explained in t
12. ast 64 oz of water Replace and tighten the primer cap IMPOR TANT The spa jet unit may be seriously damaged if the pump is not properly primed or if the primer cap is not replaced and fully tightened PRIMER PLUGGING IN THE HYDROTHERAPY SPA Once the hydrotherapy spa is filled with enough water to cover the water jets and the pump has been primed the power cord can be plugged in and the spa jet unit can be turned on Note The first time the power cord is plugged in the spa jet unit will turn on automatically 10 Grounded circuit capable of carrying 15 or more amps When connecting the power cord plug the power cord directly into a grounded circuit capable of carrying 15 or more amps No other appliance should be on the same circuit Replace the power cord immediately if it becomes damaged The power cord is equipped with a Ground Fault Circuit Interrupter GFCI located at the end of the power cord You should always test the GFCI before using the hydrotherapy spa First turn on the hydrotherapy spa by pressing the power button on the console Once the unit is run ning press the GFCI test button The hydrotherapy spa should shut off Press the reset button The hydrotherapy spa should resume normal operation If the hydrotherapy spa continues to run after the test button is pressed then the GFCI is damaged Do not use the hydrotherapy spa until the GFCI has been repaired or replaced by a q
13. ccurs then the liner may have an air leak Locate the leak and patch it using a pool patch kit that you can purchase at any pool and spa supply store ORDERING REPLACEMENT PARTS To order replacement parts simply call our Customer Service Department toll free at 1 800 999 3756 Monday through Friday 6 a m until 6 p m Mountain Time excluding holidays To help us assist you please be pre pared to give the following information when calling 1 The MODEL NUMBER of the product IMHS80081 2 The NAME of the product IMAGE RENEW 800 3 The SERIAL NUMBER of the product see the front cover of this manual 4 The KEY NUMBER and DESCRIPTION of the part s see the PART LIST EXPLODED DRAWING attached to the center of this manual Part No 154414 J00437AC RO499A Printed in USA 1999 ICON Health amp Fitness Inc PART LIST Model No IMHS80081 Key No Qty OONDARWNDN BR PR RA S G AH SHB BSB BSB eSB BSB eB as YO HH HaHeasBe RAH HSH ANY A AH SH HSH Description Side Panel Rubber Grommet Dual Temperature Probe Support Ball 8 x 5 8 Screw Removable Collar 1 4 x 1 1 2 Bolt Fabric Spa Surround Inflatable Spa Liner Fixed Jet Spa Cover Lower Heater Gasket Spa Jet Unit Heater 4 x 3 8 Screw Filter 10 x 1 1 4 Screw Suction Cover Suction Guard Pump Motor Heater Terminal Cover Heat Controller Heater Wire Harness 10 Keep Nut Electronic Control Primer Housing Headrest w Fasteners
14. consequential damages arising out of or in con nection with the use or performance of the product or damages with respect to any economic loss loss of property loss of revenues or profits loss of enjoyment or use costs of removal installation or other consequential damages of whatsoever nature Some states do not allow the exclusion or limitation of inci dental or consequential damages Accordingly the above limitation may not apply to you The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein Some states do not allow limitations on how long an implied warranty lasts Accordingly the above limitation may not apply to you This warranty gives you specific legal rights You may also have other rights which vary from state to state ICON HEALTH amp FITNESS INC 1500 S 1000 W LOGAN UT 84321 9813 IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of drowning electric shock or serious injury read the following important precautions before using the hydrotherapy spa READ AND FOLLOW ALL INSTRUCTIONS 10 11 12 13 14 It is the responsibility of the owner to ensure that all users of the hydrotherapy spa are adequately informed of all precautions Use the hydrotherapy spa only as described in this manual The hydrotherapy sp
15. containers closed tightly when not in use 6 Never add water to the chemicals always add the chemicals to the water as directed 7 Always store chemicals in a cool dry place MAINTAINING THE PROPER PH BALANCE The pH factor is a measure of relative acidity or alka linity in the water It is measured on a scale of 1 to 14 Pure water has a value of 7 which is neutral Any value above 7 is alkaline and any value below 7 is acidic You should maintain a slightly alkaline pH level between 7 2 and 7 8 in the hydrotherapy spa Severe problems can occur when the pH balance is not maintained within this range If the pH level exceeds 7 8 dissolved minerals can build up and clog the plumbing in the spa jet unit If the pH level falls below 7 2 the acid level in the water will begin to cor rode the metal parts in the spa jet unit Also the sani TROUBLE SHOOTING tation agents in the water will not be effective if the pH level is not properly maintained Damage caused by improper pH levels is not covered under the warranty To maintain the proper pH level you should test the pH of the water regularly To test the water you can either purchase additional test strips or purchase a pH test kit at a pool and spa supply store The pH reading should be between 7 2 and 7 8 If the level is too low add a pH increaser usually soda ash If the level is too high add a pH reducer usually sodium bisulfate Test the water again after five
16. d oe cd ne ead Dae eaten 14 ORDERING REPLACEMENT PARTS 0 00 0 anana Back Cover Note A PART LIST and an EXPLODED DRAWING are attached to the center of this manual Remove the PART LIST and EXPLODED DRAWING before beginning assembly IMAGE is a registered trademark of ICON Health amp Fitness Inc LIMITED WARRANTY ICON Health amp Fitness Inc ICON warrants this product to be free from defects in workmanship and material under normal use and service conditions for a period of ninety 90 days from the date of pur chase This warranty extends only to the original purchaser ICON s obligation under this warranty is lim ited to replacing or repairing at ICON s option the product at one of its authorized service centers All products for which warranty claim is made must be received by ICON at one of its authorized service cen ters with all freight and other transportation charges prepaid accompanied by sufficient proof of purchase All returns must be pre authorized by ICON This warranty does not extend to any product or damage to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage or repairs not provided by an ICON authorized service center products used for commercial or rental pur poses or products used as store display models No other warranty beyond that specifically set forth above is authorized by ICON ICON is not responsible or liable for indirect special or
17. e console have not been used for longer than twenty minutes the automatic mode will begin filtering or heating the water as needed Note to keep the filter and heat cycles from run ning the power cord must be unplugged The whirlpool jet B located on the left side of the spa jet unit directs the flow of the water to create a whirlpool action in the hydrotherapy spa The suction vent C located on the right side of the spa jet unit pulls the water into the spa unit in order to operate the system The suction cover should always be in place over the suction vent Never operate the spa without the suction cover in place Filter Cover The filter D is locat ed on the left side of the spa jet unit behind the filter cover The fil ter can be removed for cleaning and replace ment by removing the filter cover and the two filter cover screws and then pulling the filter from the spa jet unit The spa jet unit features an automatic filter cycle and freeze protection If the spa jet unit has not been oper ated for three hours the pump will begin circulating the water for twenty minutes to filter any impurities Also if the water temperature falls below 40 F the pump will begin circulating and heating the water to prevent the water from freezing DRAINING THE HYDROTHERAPY SPA To drain the hydrotherapy spa you must use a garden MAINTENANCE CLEANING THE INFLATABLE SPA LINER The liner shou
18. emove the spa jet unit from the side panels Be careful not to tear the inflatable spa liner Locate the pump inside the spa jet unit Remove the drain plug from the pump Tip the spa jet unit slightly until all the water has drained from the pump Replace the drain plug MAINTAINING THE SPA COVER The spa cover should be cleaned monthly Remove the support ball from the spa cover then hang the spa cover over a clothes line and spray it with a hose Leave the cover on the clothes line until it is fully dry WINTER USE AND CARE The hydrotherapy spa is designed for year round use If you decide to store the spa for the winter store it in a warm dry location See DRAINING THE HYDROTHERAPY SPA and DRAINING THE PUMP on this page WATER CHEMISTRY The hydrotherapy spa comes with a starter chemical pack for maintaining the water in the spa See TEST ING AND TREATING THE WATER on page 11 Additional chemicals can be purchased at a pool and spa supply store CAUTION The chemicals used to maintain the pH balance of the water and to sanitize the water can be dangerous Always follow these basic guide 13 lines when handling the chemicals 1 Always read and follow the directions on the label unless directed otherwise 2 Never mix different chemicals 3 Keep all chemicals out of the reach of chil dren and pets 4 Do not exceed the recommended amounts follow the directions on the label closely 5 Keep all
19. he packing During assembly make sure that all parts are ori materials until assembly is completed ented as shown in the drawings e Assembly requires two people 1 Before beginning assembly be sure that you have read and understand the information in the box above and on the previous page Unfold the pre assembled Fabric Spa Surround 8 and Side Panels 1 2 until the assembled unit is round Check the self attaching connections between the Fabric Spa Surround 8 and Side Panels 1 2 to be sure that all connections are firm Be sure that all six cover buckles are fully inserted through the slots in the Side Panels 1 2 2 Unfold the Inflatable Spa Liner 9 Attach the nozzle on the included air pump to the valve on the side of the Inflatable Spa Liner 9 Use Inflate here the air pump to fill the sides of the Inflatable Spa second Liner with air Attach the nozzle on the air pump to the valve on the floor of the Inflatable Spa Liner 9 Use the air pump to fill the bottom of the Inflatable Spa Liner with air Attach the nozzle on the air pump to the valve on top of the Inflatable Spa Liner 9 Use the air pump to fill the cushion on the top of the Inflatable Spa Liner with air 3 Be sure that the flap on the Fabric Spa Surround 8 is on the outside of the Fabric Spa Surround and Side Panels 1 2 Insert the Inflatable Spa Liner 9 into the Fabric Spa Surround Align the valve in the Inflatable Spa
20. his man ual see page 13 Failure to do so may cause injury to users or damage to the spa jet unit and will void the warranty The water pump in the spa jet unit must be primed before you use the hydrotherapy spa the first time You must also prime the pump before using the unit each time you re fill the spa The spa jet unit may be seriously dam aged if the pump is not properly primed see PRIMING THE SPA JET UNIT on page 10 DANGER When connecting the power cord see PLUGGING IN THE HYDROTHERAPY SPA on page 10 plug the power cord direct ly into a grounded circuit capable of carrying 15 or more amps No other appliance should be on the same circuit Replace the power cord immediately if damaged Do not use an extension cord with the hydrotherapy spa This could damage the motor and will void the warranty DANGER If you will be using the hydrother apy spa outside do not bury the power cord you should also keep the power cord away from lawn mowers hedge trimmers and other similar equipment WARNING The power cord is equipped with a Ground Fault Circuit Interrupter GFCI located at the end of the power cord The GFCI must be tested before each use To test the GFCI press the test button while the spa jet unit is running The spa jet unit should shut off Press the reset button The spa jet unit should resume normal oper ation If the spa jet unit continues to run after the test button is pre
21. ld be cleaned with a mild soap solution Do not use solvents The liner should always be clean and dry before being moved or stored CHECKING AND CLEANING THE FILTER The filter should be checked periodically for build up of dirt and oil If the filter needs to be cleaned follow the steps below 1 Turn off the power 2 Remove the two screws and cover from the spa jet Then pull the filter out of the unit 3 Check the filter for any dirt or debris If the fil ter needs to be cleaned rinse the filter with a hose If the filter still is dirty you will need to soak it in a cleaning solution which can be obtained from a pool and spa supply store 4 Inspect the filter for damage Replace the fil ter if there are any signs of damage 5 Re insert the cleaned filter and re attach the two screws and cover to the spa jet unit hose to siphon the water Place one end of the hose in the spa and hold it in front of a hydrotherapy jet until there is a flow of water coming out of the hose Turn off the spa unit and unplug the power cord The unit will be damaged if it is run without water cir culating Be sure the end of the hose in the spa is on the floor of the spa DRAINING THE PUMP After the hydrotherapy spa is drained see DRAINING THE HYDROTHERAPY SPA above the pump in the spa jet unit should also be drained if the spa will be stored for more than thirty days or if it may be exposed to freezing temperatures To drain the pump r
22. mperature should never exceed 104 F 40 C Temperatures between 100 F 38 C and 104 F 40 C are considered to be safe for healthy adults However if you plan to remain in the hydrotherapy spa for more than 10 to 15 minutes a lower temperature is recommended Lower temperatures are also recommended for children WARNING To reduce the risk of injury Always use an accurate thermometer to determine the water temperature before using the hydrotherapy spa WARNING To reduce the risk of injury Pregnant women should consult with their physician before using the hydrotherapy spa Pregnant women should not use the spa if the water temperature is above 100 F 38 C 28 29 30 31 32 33 the unborn child could be seriously harmed DANGER To reduce the risk of drowning Prolonged immersion in the hydrotherapy spa may cause hyperthermia a dangerous condition which occurs when the internal body temperature rises several degrees above the normal body temperature of 98 6 F The symptoms of hyperthermia are nausea dizziness drowsiness and fainting Effects include a lack of awareness inability to per ceive heat or danger and a greater risk of drowning due to a loss of consciousness Special note Individuals suffering from hyperthermia may be unable to realize that they must exit the spa and they also may be physically unable to do so WARNING To reduce the risk of drowning Heat from the wate
23. of the spa jet unit of the hydrotherapy spa Locate the labels and familiarize yourself with this information The label on the side of the spa jet unit is an adhesive decal If this decal is missing or if it is not legible please call our Customer Service Department toll free at 1 800 999 3756 Monday through Friday 6 a m until 6 p m Mountain Time to order a replacement decal Apply the decal in the location shown AVOID DROWNING RISK STAY OFF COVER WILL NOT SUPPORT WEIGHT KEEP CHILDREN AWAY CHILDREN OR OBJECTS CANNOT BE SEEN UNDER COVER REMOVE STANDING WATER CHILD CAN DROWN ON TOP OF COVER REMOVE COVER S COMPLETELY BEFORE ENTRY OF BATHERS ENTRAPMENT POSSIBLE NON SECURED OR IMPROPERLY SECURED COVERS ARE AHAZARD FAILURE TO FOLLOW ALL INSTRUCTIONS MAY RESULT IN INJURY OR DROWNING THIS IS NOT A SAFETY COVER AWARNING TO REDUCE RISK OF INJURY DROWNING OR ELECTROCUTION Read user s manual before using this spa Inspect reena and replace any worn parts immediately Supervise children at all times Reattach the spa cover after each use Spa heat may cause hyperthermia and unconsciousness If using alcohol drugs or medication spa heat may cause unconsciousness Keep all electrical appliances at least 5 feet away from spa Never place entire spa jet unit in water refer to user s manual for proper installation BEFORE YOU BEGIN Thank you for selecting the IMAGE RENE
24. r in conjunction with alco hol or drugs can cause unconsciousness Do not use the hydrotherapy spa if you are under the influence of drugs or alcohol WARNING To reduce the risk of injury or drowning Consult your physician about pos sible side effects of any medications you may be taking before using the hydrotherapy spa Heat from the water in conjunction with some medications may cause drowsiness and increase the risk of drowning Others can effect blood pressure heart rate and circula tion WARNING To reduce the risk of injury It is especially important for persons over the age of 35 or persons with pre existing health problems such as obesity heart disease high or low blood pressure circulatory prob lems or diabetes to consult your physician before using this product If you feel pain or dizziness at any time while using the hydrotherapy spa discontinue use and contact a physician WARNING The spa jets produce a stream of water with relatively high pressure Prolonged exposure of a localized area of the body may cause bruises to the skin WARNING Read all instructions before using the hydrotherapy spa ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product SAVE THESE INSTRUCTIONS WARNING LABEL IDENTIFICATION The warning labels shown below have been placed on the spa cover printed inside the inflatable spa liner and placed on the side
25. ssed then the GFCI is damaged Do not use the hydrotherapy spa until the GFCI has been repaired or replaced by a qualified electrician Keep all electrical appliances such as radios telephones televisions and lights at least five feet 1 52 meters away from the water A wire connector is provided on the pump 22 23 24 25 26 27 motor of this unit to connect a minimum No 8 AWG 804 mm solid copper conductor between this unit and any metal equipment electrical enclosure made of metal metal water pipes or conduit within five feet 1 52m of the unit DANGER Risk of electric shock Do not set up the hydrotherapy spa within five feet of any metal objects or surfaces As an alterna tive you may use the spa within five feet of metal objects if each metal object is perma nently connected to the wire connector on the pump motor of this unit by a minimum No 8 AWG 804 mm solid copper conductor see instruction 21 DANGER Risk of drowning Exercise extreme caution to prevent unauthorized and unsupervised use of the hydrotherapy spa by children Children must always be super vised DANGER To reduce the risk of drowning e Never use the spa alone Children should not use the spa unless they are supervised by an adult e Keep pets away from the spa at all times Always replace and lock the spa cover when the spa is not in use WARNING To reduce the risk of injury The water te
26. the spa Allow the water to circulate for five min utes You should now test the pH level of the water Use the included test strips to check the pH of the water Refer to the instructions on the test strip pack aging to see how to use the test strips 11 If the level is too low add half of one of the QUICK pHix It UP packets to the water Let the water circu late through the spa jet unit for five minutes Test the pH level again Repeat until the pH level is correct If the level is too high add half of one of the QUICK pHix It DOWN packets to the water Let the water cir culate through the spa jet unit for five minutes Test the pH level again Repeat until the pH level is cor rect Replace the spa cover and allow the water to contin ue to heat See WATER CHEMISTRY on page 13 for information concerning proper water maintenance SECURING THE SPA COVER The spa cover can be secured by snapping the latches on the spa cover into the buckles on the side panels The buckles can be locked by inserting the key and turning it clock wise a quarter turn To unlock the buckles insert the key and turn it counter clockwise a quarter turn Always keep the buckles locked when the spa is not in use Keep the keys in a safe place out of the reach of children DIAGRAM OF THE CONSOLE PRIMER AIR CONTROL a N IMPORTANT Ye USING THE CONSOLE Refer to the console diagram above The function of each
27. ualified electrician STARTING THE HYDROTHERAPY SPA Once you have tested the GFCI you should verify the water flow from the pumping unit Set the air control on the console to the lowest setting see USING THE CONSOLE on the next page The pumping unit will heat the water as it pumps Cover the hydrotherapy spa with the spa cover The spa cover must be tight The water will heat at about 1 7 F an hour with the cover on If you are using the hydrotherapy spa indoors and the room temperature is maintained at 70 F it will take approximately 20 to 28 hours for the water to reach the set temperature The temperature and water flow can be set or changed by the controls on the console see USING THE CONSOLE on the next page TESTING AND TREATING THE WATER The hydrotherapy spa comes with a starter chemical pack for maintaining the water in the spa Disregard the directions on the individual packages of QUICK pHix It DOWN and QUICK pHix It UP However the directions on the bottle of Non chlorine Shox and Bromine Base are correct Always keep the chemi cals away from children and pets The first time you use the spa you should test and treat the water Once you have verified that the spa jet unit is functioning properly and have allowed the water to circulate for a while you should remove the spa cover and add 1 3 of the Bromine Base bottle and 1 3 of the Non chlorine Shox bottle to the water in
28. utomatic mode which heats and filters the water when the spa is left unattended When the spa jet unit is first plugged in or if the buttons on the console have not been used for longer than twenty minutes the automatic mode will begin filtering or heating the water as needed To keep the filter and heat cycles from running the power cord must be unplugged Special Note If the unit is to be kept outdoors in cold weather you must allow the spa to maintain a safe temperature by running in automatic mode Allowing the spa jet unit to freeze will damage the unit If you do not want to use the spa during the winter store it in a warm dry location see WINTER USE AND CARE on page 13 SYMPTOM THE WATER LEVEL DROPS a b Some water loss due to evaporation is normal If rapid water loss occurs or if you notice wet ness on the floor around the hydrotherapy spa then the liner may have a leak Locate the leak and patch it using a pool patch kit that you can purchase at any pool and spa supply store Aclamp or seal inside the spa jet may be loose Check the floor around the spa jet unit for excess water and watch the spa jet unit while it is operating to see if water drips from the spa jet unit housing If you can identify the location of the leak inside the spa jet unit tight en the clamp or replace the damaged seal SYMPTOM THE INFLATABLE SPA LINER LOSES AIR a Over time some air loss is normal If rapid air loss o
29. y be dirty or damaged Remove the filter housing from the spa jet unit and clean or replace the filter b The pump may have a foreign object stuck in the impeller Contact our customer service department c The pump may have a loose wire connection Contact our customer service department 4 SYMPTOM THE PUMP HUMS BUT DOES NOT ROTATE a The pump may be jammed Contact our cus tomer service department 5 SYMPTOM THE PUMP IS NOISY WHILE OPERATING a There may be debris in the pump Contact our customer service department 14 b The pump may have a bad bearing Contact our customer service department 6 SYMPTOM THE WATER DOES NOT HEAT a The heater is attached to the pump in the spa jet unit If the pump is operating the water should heat Cover the hydrotherapy spa with the spa cover The spa cover must be tight Set the air control to low The water will heat at a rate of 1 7 F an hour If you are using the spa indoors and the room temperature is main tained at 70 F it will take approximately 20 to 28 hours for the water to reach the set temper ature b If you are using the hydrotherapy spa outdoors it may take longer for the water to heat See the chart below for the approximate heating time Air Temperature Heating Time 70 F 20 to 28 hours 50 F 70 F 1 to 2 days 30 F 50 F 2 to 3 days If the water still has not heated after three days contact our customer service department
Download Pdf Manuals
Related Search