9.7-INCH VALUE LED CCTV MONITOR
Contents
1. gt NEVER REMOVE THE BACK COVER Removal of the back cover should be carried out only by qualified personnel DO NOT USE IN HOSTILE ENVIRONMENTS To prevent shock or fire hazard do not expose the unit to rain or moisture This unit is designed to be used in the office or home Do not subject the unit to vibrations dust of corrosive gases gt KEEP IN A WELL VENTILATED PLACE Ventilation holes are provided on the cabinet to prevent the temperature from rising Do not cover the unit or place anything on the top of unit gt AVOID HEAT Avoid placing the unit in direct sunshine or near a heating appliance gt TO ELIMINATE EYE FATIGUE Do not use the unit against a bright back ground and where sunlight or other light sources will shine directly on the monitor gt BE CAREFUL OF HEAVY OBJECT Neither the monitor itself nor any other heavy object should rest on the power cord Damage to a power cord can cause fire or electrical shock 9 7 INCH VALUE LED CCTV MONITOR seeren 05 29 FCC RF INTERFERENCE STATEMENT NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interfer2. 127 9 7 INCH VALUE LED CCTV MONITOR _ BE MOUNTING GUIDE gt Wall mount Option 1 Using the 75 mm VESA holes 2 Using the VESA standard wall mount design and the 75mm hole pattern on the back side to install the LED monitor to the wall ei M4x10 screws X Attention You must use four M4x10 screws to assemble this monitor and the wall mount bracket 9 7 INCH VALUE LED CCTV MONITOR seese 13 D SUB CONNECTOR PIN ASSIGNMENTS gt PIN ASSIGNMENTS RED VIDEO GREEN VIDEO SIGNAL CABLE DETECT BLUE VIDEO GROUND GROUND SDA for DDC GROUND H SYNC or H V SYNC RED GROUND V SYNC GREEN GROUND CL for DDC BLUE GROUND D SUB gt ACCESSORY 1 Power adaptor 2 User s manual 3 Cable PC or HDMI 4 Trigger cable 5 Stereo cable Option 6 Wire Stand Option 7 Wall mount Option 14 MM 9 7 INCH VALUE LED CCTV MONITOR BEL Power MANAGEMENT Power Consumption Mode Power Consumption Turned On lt 8 2W Turned Off lt 0 5W gt LED Indicator The power management feature of the monitor is comprised of three stages Turned on Green No signal AV mode Green VGA mode Blinking green and Turned off LED off Mode LED Monitor Operation Turned On Green Normal Operation No Signal VGA PC mode Blinking green Not Operation Turned Off LED off Not Operation BIT SPECIFICAT
3. Product Waste Electrical amp Electronic Equipment Applicable in the European Union and other European countries with separate collection systems This marking shown on the product or its literature indicates that it should not be disposed with other household wastes at the end of its working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take this item for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract E This product should not be mixed with other commercial wastes for disposal Power switch should be in the ON position Check that the Brightness and or the contrast adjustments of the Display have not been turned down to minimum levels The video card should be completely seated in its slot L39ME0390 Rev 0
4. be a few seconds delay before the display appears 6 POWER LED Turned on with VGA or AV signals Green color Turned on with no signal 1 AV mode Green color 2 VGA PC mode Blinking green color Turned off LED off 9 7 INCH VALUE LED CCTV MONITOR 07 08 en 9 7 INCH VALUE LED CCTV MONITOR CONTROLS AND FUNCTIONS CONTROLS AND FUNCTIONS B BACK gt PC Menu Description All picture sound settings and setup for the monitor can be adjusted in the OSD menu 1 AUDIO IN On Screen Display O gt To adjust the OSD screen 2 VGA 1 Press the MENU button to enter the OSD menu 2 Press the A 4 v buttons to select the desired option The selected option is highlighted 3 HDMI 3 Press the INPUT button to enter the submenu for adjusting items 4 Change the value you wish to adjust by using the A 4 vw buttons 4 DC 12V O gt 5 Press the MENU button to exit the submenu for adjusting items 6 Press the MENU button to exit the OSD menu PC CONTRAST mu 50 BRIGHTNESS M 50 H POSITION mu 50 9 V POSITION N ooo CLOCK A 50 PHASE u 5 COLOR TEMP gt 4 gt Lr AUTO ADJUST gt SELECT I ADJUST MENU EXIT PC Only PC Mode CONTRAST Adjusts intensity of the image 0 100 BRIGHTNESS Adjusts brightness of the screen 0 100 H POSITION Move OSD horizontally on screen right or left 0 100 V POSITION Move OSD vertically on screen up or
5. IONS 9 7 INCH VALUE LED CCTV MONITOR seese 15 g LED Type 9 7 Diagonal AM TFT Active Matrix Pixel pitch mm 0 192 H x 0 192 V Brightness 350cd m Typical Contrast Ratio 600 1 Typical Response Time 35msec Typical RESOLUTION H x V 1024x768 60Hz FREQUENCY HORIZONTAL 31 48KHz VERTICAL 56 60Hz INPUT SIGNAL HDMI IN VGA RGB PC AUDIO IN ACTIVE DISPLAY AREA H x V 196 608mm x 147 456mm PACKING DIMENSIONS WxDxH 335mm x 280mm x 100mm 13 19 x 11 02 x 3 94 WEIGHT Net 1 24kg 2 73 Ibs Gross 2 4kg 5 29 Ibs ELECTRICAL RATINGS 12V 0 68A 100 240V 50 60Hz gt gt NOTE Technical specifications are subject to change without notice Uem 9 7 INCH VALUE LED CCTV MONITOR t Ld TROUBLESHOOTING GUIDE TROUBLE TROUBLESHOOTING TIP Check that power cord of the Monitor have been connected securely into wall outlet or grounded extension cable or strip No image on display screen and LED is it The signal cable should be completely NO SIGNAL connected to the video card computer message on screen and the computer is switched On Display image is not centered too small or too large in PC mode Push the down key in front side Vertical or Horizontal noise is present in the picture Adjust clock and Phase in the OSD WEEE Symbols Correct Disposal of This
6. USER MANUAL 9 7 INCH VALUE LED CCTV MONITOR anu o zie Please read this manual thoroughly before use and keep it handy for future reference ENG 9 7 INCH VALUE LED CCTV MONITOR eee BB SAFETY INSTRUCTION rer CAUTIONS ee rer ECC RF INTERFERENCE STATEMENT RI ere CONNECTING WITH EXTERNAL EQUIPMENT MH CONTROLS AND FUNCTIONS see mI n mI nmn eme nnne MOUNTING GUIDE sea a a D SUB CONNECTOR PIN ASSIGNMENTS Rm POWER MANAGEMENT s Im eI nere herein sens SPECIFICA IONS een TROUBLE SHOOTING GUIDE mmm This Monitor was Oc ui A U 12 13 14 15 16 Manufactured by ISO 9001 Certified Factory Uem 9 7 INCH VALUE LED CCTV MONITOR BI SAFETY INSTRUCTION oy ew IN Important Safety Instruction Read these instructions Keep these Instructions Heed all warnings Follow all instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturers instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat Do not defeat the safety purpose of the polarized or grounding type plug Apolarized plug has two blades with one wider than the other Agrounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided f
7. down 0 100 CLOCK Adjusts the vertical noise of screen image 0 100 PHASE Adjusts the number of horizontal picture elements 0 100 COLOR TEMP Select the color temp of picture See the table on Next page AUTO ADJUST Selects the type of auto adjustment 9 7 INCH VALUE LED CCTV MONITOR seese 09 B OB CONTROLS AND FUNCTIONS gt COLOR TEMP Menu Description 1 Press the MENU button to enter the OSD menu 2 Press the A 4 V buttons to select the desired option The selected option is highlighted 3 Press the INPUT button to enter the submenu for adjusting items 4 Change the value you wish to adjust by using the A 4 vw buttons 5 Press the MENU button to exit the submenu for adjusting items 6 Press the MENU button to exit the OSD menu COLOR TEMP USER R USER G USER B SELECT I ADJUST MENU NORMAL Gives the white color a neutral tint WARM Gives the white color a reddish tint COLD Gives the white color a bluish tint USER To manually adjust the color tones Red Green Blue 10 en 9 7 INCH VALUE LED CCTV MONITOR CONTROLS AND FUNCTIONS gt AUDIO Menu Description 1 Press the MENU button to enter the OSD menu 2 Press the A 4 v buttons to select the desired option The selected option is highlighted 3 Press the INPUT button to enter the submenu for adjusting items 4 Change the value you wish to adjust by using the A 4 vw bu
8. ence to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Only shielded interface cable should be used Finally any changes or modifications to the equipment by the user not expressly approved by the grantee or manufacturer could void the users authority to operate such equipment gt DOC COMPLIANCE NOTICE This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the radio interference regulation of Canadian Department of communications 06 M 9 7 INCH VALUE LED CCTV MONITOR CONNECTING WITH EXTERNAL EQUIPMENT J A FRONT 1 INPUT Selects AV or HDMI inputs Selects an option in the OSD 2 MENU Activates or exits the OSD Moves previous menu or status in the OSD 3 4 4 4 V gt Moves another option in the OSD 5 9 1 POWER ON OFF Turns the power on or off There will
9. or your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the bsolete outlet Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus Only use attachment accessories specified by the manufacturer Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use caution when moving the cart apparatus combination to avoid injury from tip over e Unplug this apparatus during lightning storms or when unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 9 7 INCH VALUE LED CCTV MONITOR seese 03 JE SAFETY INSTRUCTION The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids such as vases shall be placed no the apparatus Minimum distances e g 10cm around the apparatus for sufficient ventilation WARNING To reduce the risk of fire or electric shock do not expose the apparatus to rain or moisture The apparatus shall not be expo
10. sed to dripping or splashing and no objects filled with liquids such as vases shall be placed on the apparatus CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE REAR COVER NO USER SERVICEABLE PARTS INSIDE REFER TO QUALIFIED SERVICE PERSONNEL This symbol is intended to alert the user to the presence of uninsulated dangerous voltage with in the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons This symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance 04 nn 9 7 INCH VALUE LED CCTV MONITOR CAUTIONS CAUTION The power supply cord is used as the main disconnect device ensure that the socket outlet is located installed near the equipment and is easily accessible ATTENTIONN Le cordon d alimentation est utills comme interrupteur g n ral La prise de courant doit tre situ e ou install e proximit du mat riel et tre facile d acces CAUTION TO SERVICE PERSONNEL POWER SUPPLY CORD IS USED AS MAIN POWER DISCONNECT DEVICE IN THIS PRODUCT UNPLUG THIS PRODUCT FROM THE WALL OUTLET BEFORE REMOVING THE BACK COVER AND SERVICING EMISSION CHARACTERISTICS TESTED BY SEMKO THIS PRODUCT HAS BEEN TESTED AND HAS SHOWN COMPLIANCE WITH THE NATIONAL SPECIFICATONS SUCH AS SWEDISH MPR 1990 10 MPRII
11. ttons 5 Press the MENU button to exit the submenu for adjusting items 6 Press the MENU button to exit the OSD menu SOUND MODE STANDARD gt BASS 50 TREBLE uem 50 BALANCE m 50 AVC OFF gt SELECT I ADJUST MENU SOUND MODE Sets the sound mode STANDARD MOVIE MUSIC USER BASS Adjusts bass of the sound 0 100 TREBLE Adjusts treble of the sound 0 100 BALANCE Adjusts balance of the sound 0 100 AVC Set the Auto volume control ON OFF 9 7 INCH VALUE LED CCTV MONITOR seese 11 CONTROLS AND FUNCTIONS gt OSD Menu Description 1 Press the MENU button to enter the OSD menu 2 Press the A 4 V buttons to select the desired option The selected option is highlighted 3 Press the INPUT button to enter the submenu for adjusting items 4 Change the value you wish to adjust by using the A 4 vw buttons 5 Press the MENU button to exit the submenu for adjusting items 6 Press the MENU button to exit the OSD menu LANGUAGE ENGLISH H POSITION V POSITION DURATION HALFTONE MEMORY RECALL SELECT SS ADJUST MENU LANGUAGE Sets the language of the OSD menu E De i H POSITION Move OSD horizontally on screen right or left 0 100 V POSITION Move OSD vertically on screen up or down 0 100 DURATION Adjust OSD displaying time 0 100 HALFTONE Adjusts the halftone 0 100 MEMORY RECALL Resets the monitor settings to the factory default
Download Pdf Manuals
Related Search