T SWITCH TEMPO AUTOMATIC LIGHTS SWITCH USer MAnUAL
Contents
1.2. JAE T SWITCH TEMPO AUTOMATIC LIGHTS SWITCH USER MANUAL A WARNING Carefully read following instructions and technical specifica Green tions in this manual before installation The system must be installed and used n l N f f voltage which controls the low beam lights If you want to use the feature Coming only according to this manual The system is designed for vehicles with 12V H en oh i To kanie i power supply It has to be connected to 12V output and to the ground Neither NS a ene eee ee Ug ce ee Ser a a producer or seller of the system is responsible for damages caused by incor rect installation using or operating of this product Unprofessional operation or modification of the system can damage the system alone or the electric sys tem of the vehicle and leads to warranty loss For proper working of the system CONNECTOR CN2 White Violet TEMPO T SWITCH provides automatic lights switching low beam and parking after pressure sensor TEMPO T SWITCH turns on the parking lights and low beam right starting the vehicle lts advantages are simple construction maintenance free opera 2 after the start Responds to the input pulse we recommend the installation to be made by authorized service SYSTEM DESCRIPTION tion and easy installation into the vehicle It is parallel connected to the vehicle lights switch which remains in the off position when are the lights automatically turn on
3. TEMPO T SWITCH includes convenience function Coming Home Also includes input to ensure automatic turns off the low beam lights when beam lights are switched on bulb type H4 lights for 30 seconds to unlock lock the car connection with car alarm or central period the lights automatically turn off I SYSTEM INSTALLATION Remove plastic covers of car dashboard Find cables for T SWITCH connection Use function specific cable does have After choosing the right cables disconnect the car battery and connect the cable harness of T SWICHT to those cables according to the attached wiring schemes Solder and isolate all connections After finishing T SWITCH and the electrical installation of the car ignition directional lights Mount the plastic covers back on to the dashboard POSITION OF CONTROL UNIT Attach it using doublesided adhesive tape or cable ties ll WIRES CONNECTION CONNECTOR CN1 White light Wiring diagram parking lights input 12V low beam input 12V low beam output 12V CN2 brown parking lights Activating of the function white output Coming home input brown parking lights Sensing alternator purple output v input i grey parking lights P TU output skelet black orange beam headlights input ignition yellow red 12V input Input cable to control the parking lights For this wire bring voltage which
4. controls parking lights When the parking lights are controlled by a negative voltage can be used only gray wire of the connector CN2 as the output wire When the lights are controlled by positive voltage you can use all three outputs for parking Input to control the low beam lights On this wire must be bring the same is turned off Blue Relay output to control the low beam lights The polarity of this output is dependent on voltage on the green wire in the connector CN1 Input to the activation of Coming Home Input responds to pulse Connect to the output of the alternator G or the output signal from oil Black Connect to the GND of vehicle Yellow Connect to the ignition wire 12 V Red Connect to battery 12 V Orange If you need to turn the low beam off when beam lights are switched on l l connect the cable to the beam Responds to the input pulse If is 12V on this Coming home function This feature provides automatic turn on of low beam input output for low beam will be turned off Ma ddi ne _ Grey locking vehicle is necessary If you turn on the ignition before the expiration of this pendent on voltage on the white wire in the connector CN1 Connect to the control wires of the parking lights Brown ghts This output can be used only when the parking lights are controlled by a positi ve voltages If the parking lights are controlled by negative voltage use the gray a digital
5. multimeter to test the function of cables in vehicle even if you re sure which wire for control Relay output to control the parking lights The polarity of this output is de Output for parking lights Connect to the control wires of the parking li SETTING THE SWITCHING VOLTAGE ae TEMPO T Switch automatically turns on after starting the vehicle when the vehicle the installation of T SWITCH connect the car battery Test correct functionality of the electrical system voltage exceeds a preset value This value is factory set to13V Value can be set for each vehicle individually to the required switching voltage ac cording to schematic If during engine running and automatically turning lights on will voltage drop below the switching voltage TEMPO T SWITCH remains turned Place the control unit from the inner side of protection plastics of the car dashboard on until the ignition is turned off the yellow wire is needed to connect the ignition TECHNICAL PARAMETERS Power supply 12V 20 Operational temperature 40 C az 60 C Current comsuption stand by Max current load parking lights 3x10 A 12V Max current load low beam lights 30A 12V Connection of inputs and outputs relays for relays for low beam lights parking lights vehicle light switch Lights control using possitive voltage Oh low beam lights oy_oreen white 127V light switch dash board backlight
Download Pdf Manuals
Related Search